DUPLEX RABBET &
FILLISTER PLANE
90310
ASSEMBLY AND OPERATING INSTRUCTIONS
3491 Mission Oaks Blvd., Camarillo, CA 93011
Copyright © 2003 by Harbor Freight Tools®. All rights reserved. No portion of
this manual or any artwork contained herein may be reproduced in any shape
or form without the express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353
Download from Www.Somanuals.com. All Manuals Search And Download.
9.
Maintain tools with care. Keep tools sharp and clean for better and safer
performance. Follow instructions for lubricating and changing accessories. The
handle must be kept clean, dry, and free from oil and grease at all times.
10. Stay alert. Watch what you are doing, use common sense. Do not operate any tool
when you are tired.
11. Take caution as some woods contain preservatives such as copper chromium
arsenate (CCA) which can be toxic. When cutting these materials extra care should
be taken to avoid inhalation and minimize skin contact.
12. Check for damaged parts. Before using any tool, any part that appears damaged
should be carefully checked to determine that it will operate properly and perform its
intended function. Check for any broken parts or mounting fixtures; and any other
condition that may affect proper operation. Any part that is damaged should be
properly repaired or replaced by a qualified technician.
13. Replacement parts and accessories. When servicing, use only identical
replacement parts. Use of any other parts will void the warranty. Only use accessories
intended for use with this tool. Approved accessories are available from Harbor
Freight Tools.
14. Do not operate tool if under the influence of alcohol or drugs. Read warning
labels if taking prescription medicine to determine if your judgment or reflexes are
impaired while taking drugs. If there is any doubt, do not operate the tool.
15. Maintenance. During periods of storage, coat the bare metal surfaces with light oil to
inhibit rust.
Warning: The warnings, cautions, and instructions discussed in this instruction
manual cannot cover all possible conditions and situations that may occur. It must be
understood by the operator that common sense and caution are factors which cannot
be built into this product, but must be supplied by the operator.
Unpacking
When unpacking, check to make sure the parts shown on page 5 are included. If any parts
are missing or broken, please call Harbor Freight Tools at the number on the cover of this
manual as soon as possible.
Warning! Do not let the blades come in contact with your hands while planing or changing
the blades. They are extremely sharp and will cause severe injury if contacted.
SKU 90310
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Refer to the Assembly Drawing on page 5 and FIGURE 1 below.
Note: The front blade (fillister) is stationary and the rear blade is movable and replaceable.
1. To change or replace Blades, turn the Blade Removal Knob (see below) counterclockwise
and lift off the blade holder (see below). Set the Blade in so that it fits over the set screw and
is properly aligned. Replace the Blade Holder and tighten the Blade Removal Knob.
2. Adjust the amount of blade you want to contact the workpiece by pressing the Blade
Adjustment lever side to side (see Assembly Drawing on page 5).
FIGURE 1
Blade Removal Knob
Blade Holder
Blade
Set Screw
3. There are two fences. To adjust the Depth Gauge Fence, loosen the Lock Screw and move
the Fence up or down to determine the depth you cut into the wood (see Assembly Drawing
on page 5). To assemble the Fence located on the left side of the tool, first thread on the Steel
Rod into the left side of tool’s housing. The Fence slides over the end of the Steel Rod and is
locked in place by the Fence Adjustment knob. To adjust this Fence (determines width of
cutting area), loosen the Fence Adjuster knob and move the Fence either closer or further
from the body of the Planer. With the Fence in the desired position, secure it in place by
tightening the Fence Adjuster knob.
4. Make sure the workpiece is securely fastened down.
Note: If you are using the front blade for bullnosing (See Assembly Drawing on page 5), make
sure the rear blade is adjusted up so it doesn’t contact the workpiece.
5. Do not force the Plane or press down on it. Move it forward, taking off a little wood at a
time. If the Plane does not move forward easily, retract the Blade more as explained in step
2 above.
SKU 90310
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly Drawing
Handle
Blade Adjustment
Lever #8
Blade #1
Blade Removal
Knob #7
Fence #4
Fence Adjustment
Lock Screw #6
Steel Rod #3
Lock Screw #5
Note: This Plane includes two blades
and two fences.
Depth Gauge Fence #2
Front Blade
REPLACEMENT PARTS
#1
#2
#3
#4
#5
#6
#7
#8
Blade
Depth Gauge Fence
Steel Rod
Fence
Lock Screw
Fence Adjustment Lock Screw
Blade Removal Knob
Blade Adjustment Lever
Maintenance
1. Keep the Blades sharp and clean.
2. Do not allow wood residue to build up on the blades.
3. Wipe the Plane down with a lint free cloth regularly.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS
MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBU-
TOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE
OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS
QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER
AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS
SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE
BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER
REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING
OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
NOTE: Some parts are listed and shown for illustration purposes only and are not available
individually as replacement parts.
SKU 90310
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
|