3/4" HEAVY DUTY AIR IMPACT
WRENCH
ASSEMBLY and OPERATING INSTRUCTIONS
®
3491 Mission Oaks Blvd. / Camarillo, CA 93011
Copyright © 1997 by Harbor Freight Tools. All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in any
shape or form without the express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353.
Download from Www.Somanuals.com. All Manuals Search And Download.
Wear a full face shield if you are producing metal filings or wood chips. Wear an ANSI
approved dust mask or respirator when working around metal, wood, and chemical dusts
and mists.
9. DO NOT ABUSE THE POWER CORD. Do not yank compressor’s cord to disconnect it
from the receptacle. Do not carry tools by the cord.
10. DO NOT OVERREACH. Keep proper footing and balance at all times. Do not reach over or
across running machines.
11. MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better and safer
performance. Follow instructions for lubricating and changing accessories. Inspect
compressor’s cord periodically and, if damaged, have them repaired by an authorized
technician. Inspect all hoses for leaks prior to use. The handles must be kept clean, dry, and
free from oil and grease at all times.
12. REMOVE ADJUSTING KEYS AND WRENCHES. Make it a habit to check that keys and
adjusting wrenches are removed from the tool or machine work surface before plugging it
in.
13. AVOID UNINTENTIONAL STARTING. Do not carry any tool with your finger on the trigger,
whether it is connected to the compressor or not.
14. STAY ALERT. Watch what you are doing, use common sense. Do not operate any tool
when you are tired.
15. CHECK DAMAGED PARTS. Before using any tool, any part that appears damaged should
be carefully checked to determine that it will operate properly and perform its intended
function. Check for alignment and binding of moving parts; any broken parts or mounting
fixtures; and any other condition that may affect proper operation. Any part that is damaged
should be properly repaired or replaced by a qualified technician. Do not use the tool if any
switch does not turn on and off properly.
16. REPLACEMENT PARTS AND ACCESSORIES. When servicing, use only identical
replacement parts. Use of any other parts will void the warranty. Only use accessories
intended for use with this tool. Approved accessories are available from Harbor Freight
Tools.
17. DO NOT OPERATE TOOL IF UNDER THE INFLUENCE OF ALCOHOL OR DRUGS.
Read warning labels on prescriptions to determine if your judgment or reflexes are impaired
while taking drugs. If there is any doubt, do not operate the tool.
18. DRAIN COMPRESSOR EVERY DAY. Do not allow moisture to build up inside the
compressor. Do not allow compressor to sit pressurized for longer than one hour.
19. MAKE SURE ALL EQUIPMENT IS RATED TO THE APPROPRIATE CAPACITY. Make
sure that regulator is set at least 10 PSI lower than the lowest rated piece of equipment you
are using.
SKU 32871
Page 3
For technical questions, please call 1-800-444-3353.
Download from Www.Somanuals.com. All Manuals Search And Download.
UNPACKING
Your Impact Wrench comes completely assembled.
If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover
of this manual.
GENERAL
This Impact Wrench develops a maximum of 535 ft/lbs. of torque. The amount of torque can be
increased or decreased using the AIR REGULATOR (#46). When the Air Regulator is
completely screwed in it is at it’s lowest setting. Air pressure increases as you loosen the Air
Regulator.
SKU 32871
Page 4
For technical questions, please call 1-800-444-3353.
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
Setup
Frequent, but not excessive, lubrication is required for best performance. Oil added through the
airline connection will lubricate internal parts. An automatic airline oiler is recommended but oil
may be added manually before every operation or after about 1 hour of continuous use. Only 4
to 5 drops of oil at a time are necessary. Too much oil will collect inside the tool and be blown
out during the exhaust cycle. ONLY USE PNEUMATIC TOOL OIL. Do not use detergent oil or
additives as these lubricants will cause accelerated wear to the seals in the tool.
Dirt and water in the air supply are major causes of pneumatic tool wear. Use a filter/oiler for
better performance and longer life. The filter must have adequate flow capacity for the specific
application. Consult the manufacturer’s instructions for proper maintenance of your filter.
The connector on the tool must not hold pressure when the air supply is disconnected. If the
wrong fitting is used, the tool can remain charged with air after being disconnected and still be able
to drive a fastener. See Figure 1 for the recommended accessories and connection order.
Impact
Wrench
Figure 1 — Airline Oiler
SKU 32871
Page 5
For technical questions, please call 1-800-444-3353.
Download from Www.Somanuals.com. All Manuals Search And Download.
Use
Step 1: Set the compressor’s pressure regulator to a maximum of 90 PSI. 90 PSI is
satisfactory without harming this tool.
Step 2: You will need to purchase a union fitting (sold separately) before you can connect the
Impact Wrench to your air compressor. You may also wish to purchase an Air Coupler
as this allows quick-coupling action when using multiple tools with one compressor.
Step 3: Determine the socket size necessary for the job you need to do. Attach the appropriate
3/4" drive socket to the Impact Wrench as shown in Figure 2.
3/4“ Drive Socket
Air Coupler
Figure 2 — Attaching the Air Coupler and Socket
Step 4: Connect the Impact Wrench to the air compressor’s hose. If leaking is detected,
disconnect the air hose and repair before use.
SKU 32871
Page 6
For technical questions, please call 1-800-444-3353.
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 5: Select the power setting for Loosening by adjusting the AIR REGULATOR (#46) located
on the bottom of the Impact Wrench as shown
CAUTION
in Figure 3. When the Air Regulator is
Use the Setting Appropriate for the
completely screwed in it is at it’s lowest setting.
Job. Do Not Set the Power Setting
Air pressure increases as you loosen
Higher Than Needed. Damage to
theAir Regulator.
Parts Could Result.
Air Regulator
(#46)
Figure 3 — Adjusting the Reverse Power Setting
Step 6: Select the direction of the Wrench (forward or reverse) by pushing the REVERSE
VALVE (#48) located on the handle of the Impact Wrench as shown in Figure 4.
R
Valve in Forward Position.
Push in to Reverse
Reverse Valve
(#48)
Figure 4 — Selecting Reverse Direction
SKU 32871
Page 7
For technical questions, please call 1-800-444-3353.
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 7: Press the TRIGGER (#38) to test the Impact Wrench. The Impact Wrench should spin
freely as shown if Figure 5
R
Trigger
(#38)
Figure 5 — Pressing Trigger
Loosening
Step 1: Verify that the power level is correct for your needs and that the REVERSE VALVE (#48)
has been shifted (pressed) completely to the right. If not, refer to Steps 5 through 9
under Use before proceeding.
Step 2: Place your work in as clear a location as possible. Make sure the air hose will reach as
far as needed without stressing any connections.
Step 3: With the correct socket attached to the Impact Wrench, slide the socket over the nut or
bolt.
Step 4: Grip the Impact Wrench with both hands, especially with higher power settings. Make
sure you are in a stable position and spread your feet shoulder-width apart.
Step 5: Press the TRIGGER (#38) to loosen the bolt.
WARNING
The Impact Wrench May Kick Back
During Operation. If This
Happens, Release the TRIGGER
Step 6: If the bolt will not loosen, and you are on a low
power setting for Loosening, try increasing the
power setting and attempt again.
IMMEDIATELY!
Step 7: If the bolt will not loosen with the Impact Wrench on a higher power setting, do not
repeat attempts to loosen. You may snap the bolt or strip the threads of the stud or nut.
Try another method to loosen the bolt or nut.
SKU 32871
Page 8
For technical questions, please call 1-800-444-3353.
Download from Www.Somanuals.com. All Manuals Search And Download.
Tightening
Step 1: Verify that the power level is correct for your needs and that the REVERSE VALVE (#48)
has been shifted (pressed) completely to the left. If not, refer to Steps 5 through 9
under Use before proceeding.
Step 2: Place your work in as clear a location as possible. Make sure the air hose will reach as
far as needed without stressing any connections.
Step 3: Thread the nut or bolt on as far as possible by hand. This is to prevent cross-threading.
Step 4: If you have torque specs for the nut or bolt you are working on, refer to them. If a low
torque setting is given, it is recommended that you use a socket wrench or a manual
torque wrench to tighten as the Impact Wrench may provide too much torque, even in
the lowest power setting.
Step 5: Place the socket onto the nut or bolt.
Step 6: Grip the Impact Wrench with both hands, especially with higher power settings. Make
sure you are in a stable position and spread your feet shoulder-width apart.
Step 7: Press the TRIGGER to tighten the bolt.
Step 8: When the bolt is tight, release the TRIGGER. DO NOT OVER TIGHTEN!
MAINTENANCE
There are no user-serviceable parts in your Impact Wrench. Attempts to repair or make
adjustments on your tool are prohibited and will VOID your warranty.
Refer to OPERATIONS Setup for information on maintaining your tool.
Wipe down your tool after every use and store it in a drawer or other safe place
SKU 32871
Page 9
For technical questions, please call 1-800-444-3353.
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
Item# Description
Parts#
Item# Description
Parts#
HY160-36
HY161-19
HY161-25
HY161-26
HY161-27
HY161-44
HY161-43
HY161-16
HY161-32
HY160-32
HY160-31
HY160-16
HY160-30
HY161-33
HY161-42
HY160-43
HY160-06
HY161-46
HY160-09
HY160-10
HY161-36
HY161-38
HY161-01-1
HY161-35
1
Housing
HY161-01
HY160-45
HY161-02
HY161-03
HY161-04
HY161-05
HY161-06
HY161-07
HY161-11
HY161-12
HY161-13
HY161-08
HY161-09
HY161-10
HY161-14
HY161-15
HY161-16
HY161-17
HY161-18
HY161-12
NY161-20
NY161-21
HY161-22
HY161-24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
Spring Washer
Cylinder Screw
Spring Washer
Cap Screw
Rubber
Protector, Rubber
Oil Seal
Tapping Screw
Exhaust Deflector
Pin
Spring
Set Screw
Spring Pin
Trigger
Spring Pin
2
3
4
Set Screw
Anvil Bushing
Washer
5
6
Anvil Collar
O-Ring
7
Anvil
8
9
Hammer Cage
Bearing
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Oil Seal
O-Ring
Hammer Pin
Hammer Dog
Drive Cam
Front End Plate
Rotor Blade
Rotor
Cylinder
Rear End Plate
Oil Seal
Bushing
Valve Stem
Air Control Bushing
Spring
HoseAdapter
O-Ring
Air Regulator
Air Pipe
Reverse Valve
Bearing
Rear Gasket
Rear Cover
O-Ring
WARRANTY
LIMITED 1 YEAR
WARRANTY
Harbor FreightTools Co. makes every effort to assure that its products meet high quality and durability standards,
and warrants to the original purchaser that this product is free from defects in materials and workmanship for
the period of one year from the date of purchase. This warranty does not apply to damage due directly or
indirectly to misuse, abuse, negligence or accidents; repairs or alterations outside our facilities; or to lack of
maintenance.We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent,
special or consequential damages arising from the use of our product. Some states do not allow the exclusion
or limitation of incidental or consequential damages, so the above limitation of exclusion may not apply to
you.THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges
prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise. If our
inspection verifies the defect, we will either repair or replace the product at our election or we may elect to
refund the purchase price if we cannot readily and quickly provide you with a replacement. We will return
repaired products at our expense, but if we determine there is no defect, or that the defect resulted from
causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
3491 Mission Oaks Blvd.
•
PO Box 6009
•
Camarillo, CA 93011
•
(800) 444-3353
SKU 32871
Page 10
For technical questions, please call 1-800-444-3353.
REV 04/06
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY DIAGRAM
SKU 32871
Page 11
For technical questions, please call 1-800-444-3353.
Download from Www.Somanuals.com. All Manuals Search And Download.
|