HUNTING SHELTER
Model 96529
ASSEMbLy INSTRUcTIoNS
Diagrams within this manual may not be drawn proportionally.
Due to continuing improvements, actual product may differ slightly from the product described herein.
®
Distributed exclusively by Harbor Freight Tools .
3491 Mission Oaks Blvd., Camarillo, CA 93011
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
©
®
Copyright 2007 by Harbor Freight Tools . All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions or replacement parts, please call 1-800-444-3353.
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETy RULES
1.
Dress Properly. Do not wear loose clothing or jewelry. They can be caught in
moving parts.
2.
3.
4.
Wear ANSi-approved safety goggles when assembling this product.
Only use on a sturdy tree capable of supporting the weight of the Shelter.
Fire hazard! This product IS NOT flame retardant. Do not smoke near or
introduce flames near this product.
5.
This product cannot support the weight of people or any objects. Do not sit or
stand on this product. Do not place any objects on this product.
6.
7.
8.
9.
Do not use in windy conditions.
Do not allow water or debris to accumulate on top of the Shelter.
Do not allow children to play with this product.
Avoid a dangerous environment. Do not use this product near high voltage elec-
trical lines.
10.
11.
When servicing use only identical replacement parts.
Use the right equipment. Do not use this product except for that which it is in-
tended.
12.
13.
Store idle equipment indoors. When not in use, this product should be stored
indoors in a clean, dry, safe location out of reach of children.
Check for damaged parts. Before each use, this product should be carefully
checked to determine that it will operate properly and perform its intended func-
tion. Check for alignment of parts, binding of parts, breakage of parts, mounting,
and any other condition that may affect its operation.
14.
15.
Maintain labels and nameplates on this product. These carry important safety
information. if unreadable or missing, contact Harbor Freight Tools for a replace-
ment.
The warnings, precautions, and instructions discussed in this instruction manual
cannot cover all possible conditions and situations that may occur. it must be
understood by the operator that common sense and caution are factors which
cannot be built into this product, but must be supplied by the operator.
SAVE THESE INSTRUcTIoNS.
SKU 96529
For technical questions, please call 1-800-444-3353.
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
SpEcIFIcATIoNS
Formed steel tubing / Camouflage polyester with dark olive
green draw strings and hook and loop closures.
Material
Main Tube Dimensions 5/8” O.D. x 58-11/16” Long
Recommended Tree
9-4/5” to 15-11/16”
Trunk Diameter
Rear Tree Support
18-1/2” Wide x 6” L x 3/16” Thick
Bar Dimensions
Cross Tube
5/8” O.D. x 24” Long
Dimensions
Arm Tube Dimensions 5/8” O.D. x 22-1/2” Long
Side Tube Dimensions 5/8” O.D. x 14-1/8” Wide x 48-1/2” Long
60” Long x 48” Wide x 81-1/2” High
Overall Dimensions
(includes roof and side walls fully assembled)
Net Weight
16 lb.
UNpAckING
When unpacking, check to make sure that the item is intact and undamaged. if
any parts are missing or broken, please call Harbor Freight Tools at the number shown
on the cover of this manual as soon as possible.
SET Up INSTRUcTIoNS
Read the ENTIRE IMpoRTANT SAFETy INSTRUcTIoNS section at the
beginning of this manual including all text under subheadings therein
before set up or use of this product.
Note:
For additional information regarding the parts listed in the following pages, refer
to the Assembly Diagram on page 7 of this manual.
1.
2.
Set the Main Support Frame (3) and the two pieces of Side Frame (2) on a dry,
flat, level surface. (See Assy. Diagram.)
Unfold the two Hinging Braces (4) on the Main Support Frame. Then attach the
Support Brace (5) to the Main Support Frame using two Bolts (9), two Flat Wash-
ers (15), and two Lock Nuts (16). (See Assy. Diagram.)
3.
4.
insert the two Side Frames (2) into the Main Support Frame (3), and fasten the
two Side Frames to the Main Support Frame using two Bolts (14), two Flat Wash-
ers (15), and two Lock Nuts (16). (See Assy. Diagram.)
Affix the Strips of the Fabric Cover (1) around the edges of the Main Support
Frame (3) and Side Frames (2) with the Draw Strings and Hook and Loop Clo-
sures. (See Assy. Diagram.)
ReV 09a
SKU 96529
For technical questions, please call 1-800-444-3353.
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
5.
6.
7.
Use the remaining Draw Strings to secure the rest of the Fabric Cover (1) to the
Main Support Frame (3) and Side Frames (2). (See Assy. Diagram.)
Remove the Bolt (11), Flat Washer (7), and Wing Nut (10) from one end of the
Rear Cross Bar (12). (See Figure A and Assy. Diagram.)
With assistance, position the Hunting Shelter against the trunk of a tree. Adjust
the Rear Cross Bar (12) to fit firmly against the tree trunk. Then secure the Hunt-
ing Shelter to the tree trunk by re-installing the Bolt (11), Flat Washer (7), and
Wing Nut (10) on the Rear Cross Bar. (See Figure A and Assy. Diagram.)
8.
9.
NoTE: Make sure both Bolts (11), Flat Washers (7), and Wing Nuts (10) on the
Rear Cross Bar are firmly tightened.(See Figure A and Assy. Diagram.)
Attach the Side Cover (18) to the Side Frame (2) using the 8 Hooks (17). See
diagram on page 7.
FIGURE A
REAR cRoSS bAR (12)
boLT (11)
FLAT WASHER (7)
WING NUT (10)
10.
11.
Adjust the height of the shelter so the Side Cover touch the ground. See cover
page photo.
Attach the bottom of the Side Cover (18) to the ground using the U-Shaped land-
scape Staples (19). See Parts List and Assembly Diagram on page 6 and 7.
ReV 08e
SKU 96529
For technical questions, please call 1-800-444-3353.
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANcE AND SERVIcING
Damaged equipment can fail, causing serious personal
injury. Do not use damaged equipment. If a problem occurs,
have the problem corrected before further use.
WARNING
Inspection, maintenance, and cleaning
1.
bEFoRE EAcH USE, inspect the general condition of the Hunting Shelter.
Check for loose screws, misalignment or binding of parts, cracked or broken
parts, damaged fabric, and any other condition that may affect its safe operation.
2.
3.
REGULARLy, clear off any debris or water that may accumulate on the Shelter
during use.
AFTER USE, clean the Hunting Shelter with a clean, moist cloth and mild deter-
gent. Then dry. Do not use solvents.
Troubleshooting
problem
possible causes
probable Solutions
Hunting Shelter not
properly positioned
against tree.
1. Too much slack in Rear Cross Bar. 1. Adjust Rear Cross Bar for tighter fit
against tree.
pLEASE READ THE FoLLoWING cAREFULLy
THe MANUFACTUReR AND/OR DiSTRiBUTOR HAS PROViDeD THe PARTS LiST AND ASSeMBLy
DiAgRAM iN THiS MANUAL AS A ReFeReNCe TOOL ONLy. NeiTHeR THe MANUFACTUReR OR
DiSTRiBUTOR MAKeS ANy RePReSeNTATiON OR WARRANTy OF ANy KiND TO THe BUyeR THAT
He OR SHe iS qUALiFieD TO MAKe ANy RePAiRS TO THe PRODUCT, OR THAT He OR SHe iS
qUALiFieD TO RePLACe ANy PARTS OF THe PRODUCT. iN FACT, THe MANUFACTUReR AND/OR
DiSTRiBUTOR exPReSSLy STATeS THAT ALL RePAiRS AND PARTS RePLACeMeNTS SHOULD
Be UNDeRTAKeN By CeRTiFieD AND LiCeNSeD TeCHNiCiANS, AND NOT By THe BUyeR. THe
BUyeR ASSUMeS ALL RiSK AND LiABiLiTy ARiSiNg OUT OF HiS OR HeR RePAiRS TO THe
ORigiNAL PRODUCT OR RePLACeMeNT PARTS THeReTO, OR ARiSiNg OUT OF HiS OR HeR
iNSTALLATiON OF RePLACeMeNT PARTS THeReTO.
pARTS LIST
ReV 08e
SKU 96529
For technical questions, please call 1-800-444-3353.
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
pARTS LIST
part
1
Description
Fabric Cover
Q’ty
part
11
Description
Bolt (M8x35)
Q’ty
2
1
2
1
2
1
2
4
2
6
2
2
Side Frame
12
Rear Cross Bar
Support Frame
Bolt (M5x25)
1
3
Main Support Frame
Hinging Brace
Support Brace
Bolt (M8x40)
13
2
4
14
4
5
15
Flat Washer (#5)
Lock Nut (M5)
Hooks
10
10
8
6
16
7
Flat Washer (#8)
Lock Nut (M8)
Bolt (M5x40)
17
8
18
Side Cover
1
9
19
U-Shaped Landscape Staple
8
10
Wing Nut (M8)
SKU 96529
For technical questions, please call 1-800-444-3353.
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMbLy DIAGRAM
ReV 08e
SKU 96529
For technical questions, please call 1-800-444-3353.
Page 8
Download from Www.Somanuals.com. All Manuals Search And Download.
|