4403000000_20090423_v1
ALL CLEAR
UNIT SELECTION
ODO1 SETTING (Bike1)
ODO2 SETTING (Bike2) T-TM SETTING CIRCUMFERENCE SETTING (Bike1) END SETTING
1.
3s
151640 Halfords 12 Function Computer
LCD
SEGMENTS
2s
+1
c.
BATTERY
CHANGE
+
AUTO TEST
LCD
Display
ODO1 (ODO 2)
T-TM
T-ODO
CLOCK
AVG
DST
TM
MAX
DST/D
1/2
SET
2.
1.5V
battery
LR44
MODE
Stop Status Only
Riding Status
INDEX:
2s
N
Means press button
than 2 seconds
N
more
quickly.
POPULAR TIRES CIRCUMFERENCE
REFERENCE TABLE
Circumference
5.
BIKE 1, BIKE 2 SELECTION
CLOCK SETTING
3.
4.
b.
Tire Size
N
Means press button
N
Nunber
N
=KEY NUMBER:
18 Inch
20x1.75
20 Inch
22 Inch
1436 mm
1564
1596
1759
1888
1916
1942
1995
2030
2045
2073
2099 mm
2117
2092
2124
2136
2155
2164
2174
2193
2234
2281
[•:Mode Button, : Set Button,
„
2s
2s
…
:Bike1/Bike2 Selection Button]
+1
+1
...
OK!
ATB 24x1.75
24 Inch
24x 13/8
ATB 26x1.40
ATB 26x1.50
ATB 26x1.75
26Inch (650A)
ATB26x2.0(650B)
700C TUBULAR
700x20C
a.
WHEEL CIRCUMFERENCE
BIKE 1, BIKE 2 (CIRCUMFERENCE SETTING )
6.
RESET OPERATION (AVG=0, DST=0, TM=0, MAX=0)
700x25C
700x28C
2s
2s
27 Inch(700x32c)
700x35C
700x38C
27.5 Inch
1st
28 Inch (700B)
28.6 Inch
2nd
BATTERY CHANGE (Fig. c)
1. When the brightness of the LCD display is dim, it means that the battery is nearly exhausted.
2. Replace a new LR44 (Cross reference type A76, AG13 or V13GA) battery in the compartment on the back
of the computer with the positive (+) pole toward the battery cap.
EEnngligshlish
FUNCTIONS
BUTTON AND OPERATIONS
: Current Speed
0.0–199.9Km/h (120.0 Mile/h), 0.1Km/h (Mile/h), +/- 1%
INDEX:
MODE BUTTON
•
The current speed is always displayed on the upper set when riding. It displays current speed up
to 199.9 Km/h or 120.0 Mile/h (for wheel diameters over 24 inches).
Quickly press this button to move in a loop sequence from one function screen to another. (Fig. 2)
N
2s
N
MEANS PRESS BUTTON N MORE THEN 2 SECONDS.
MEANS PRESS BUTTON N QUICKLY
{N=KEYNUMBER: •MODE Button.
SET BUTTON
„
TROUBLE SHOOTING
ODO1, ODO2: Bike1 odometer, Bike2 odometer 0.0–99999.9 Km (Miles), 0.1Km (Mile), +/- 0.1%
1. The odometer cumulates the total distance as long as the bike is running.
2. This computer design has 2 wheel circumference memories to calculate data for 2 bikes. The
odometer is separated for each bike.
SET Button. …1/2 Button.}
Press this button to get in or out the setting screens when you want to reset to bike1, bike2
„
Check the following before taking unit in for repairs.
circumference, or the current time of the
.
PROBLEM
No display
CHECK ITEM
REMEDY
MAIN UNIT SETUP (Fig.1)
INITIATE THE COMPUTER (ALL CLEAR)
1 / 2 BIKE SELECTION BUTTON …
1. Replace the battery.
1. Is the battery dead?
3. It displays one ODO data only when the bike is selected in the current status.
1. This computer design has 2 sets of circumference memory to calculate 2 bikes’ data separately.
2. Be sure that the positive pole of the
battery is facing the battery cap.
2. Is there incorrect battery installation?
1. A battery is already loaded in the main unit when purchased.
2. Hold down the MODE button •and 1/2 button …simultaneously for more than 3
seconds to initiate the computer and clear all data.
IMPORTANT: Be sure to initiate the computer before it is be used, otherwise the
computer may run errors.
3. The LCD segments will be tested automatically after the unit is initiated.
4. Press MODE button •to stop LCD test, then the flickering "Km/h".
2. Press 1/2 BIKE SELECTION button to switch between bike1 and bike 2. (Fig. 3)
T-TM: Total Riding Time
0H00M-9999H59M, 1 Minute, +/- 0.003%
1. Is it at the recalibrating or clock setting
screen?
2. Are the contacts between the
main unit and the bracket poor?
3. Are the relative positions and gap
of sensor and magnet correct?
4. Is the wire broken?
No current
Speed or
incorrect
data
1. Refer to the adjusting procedure
and complete the adjustment.
2. Wipe contacts clean.
3. Refer to Installarions (Fig.B3~B4) and
readjust data correctly.
4. Repair or replace wire.
5. Refer to "CALIBRATION" and enter
correct value.
The T-TM accumulates total riding time while riding the bike1 and bike2.
BIKE1 or BIKE2 WHEEL CIRCUMFERENCE (Cmm) RE-SETTING
1. Press the 1/2 button …to select either bike1 or bike 2. (Fig. 4)
T-ODO: Total Odometer
0.0–99999.9 Km (Miles), 0.1Km (Mile), +/- 0.1%
The T-ODO is the sum of the ODO1 plus ODO2.
2. Press the MODE button
3. Press the SET button
4. Adjusting the data as the data setting procedures.
to change to the ODO display.
enter the circumference setting screen.
•
„
: 12HR or 24HR Clock 1H00M00S–12H59M59S or 0H00M00S–23H59M59S, 1 Second, +/- 0.003%
It can display the current time either in 12HR or 24HR clock.
5. Is the circumference correct?
AVG: Average Speed
0.0–199.9 Km/h (120.0 Mile/h), 0.1Km/h (Mile/h), +/- 0.1%
CLOCK SETTING
UNIT SELECTION
Irregular
display
Refer to the "MAIN UNIT SETUP" and initiate
the computer again.
1. It is calculated from the DST divided by the TM. The average data counted is from the last
RESET to current point.
1. Change the LCD display to
screen. (Fig. 5)
Press MODE button •to choose Km/h or Mile/h. Then press the SET button
to store
„
2. Press the SET button
3. A quick press of the MODE button
to enter the clock adjusting screen to setting the clock.
„
selection.
Did you leave main unit under direct sunlight
when not riding the bike for a long time?
LCD is black
Place main unit in the shade to return to
normal state.No adverse effect on data.
2. It will display "0.0" when TM is less than 4 seconds.
to select 12HR or 24HR.
•
ODO1, ODO2 and T-TM DATA SETTING
3. It is updated about one second when TM is over 4 seconds.
4. It displays an "Err" symbol when either the TM is over 100 hours or the DST is over 1,000 km
(or miles). Reset the unit in order to restart.
4. Adjust the clock data as the data setting procedures.
Display is slow
Is the temperature below 0°C (32°F)?
Unit will return to normal state when the
temperature rises.
1. The function is designed to re-key in former data of ODO1, ODO2 and T-TM when battery is
replaced.
Assuming the current time is 13:17:15, adjusting the clock value as 13:18: --.When the current
time advances to 13:18:00, for instance, press the SET button
synchronize it with the current time. (The undisplayed Second value is restarted at 0).
to store the setting value and
„
PRECAUTIONS
2. A new user does not need to set this data. Each press of the SET button
setting data process.
skips one
„
DST: Trip Distance
0.00–999.99 Km (Miles), 0.01Km (Mile), +/- 0.01%
1. This computer can be used in the rain but should not be used under water.
2. Don’t leave the main unit exposed to direct sunlight when not riding the bike.
3. Don’t disassemble the main unit or it’s accessories.
The DST function accumulates the distance data from the last RESET operation as long as the
bike is being ridden.
RESET OPERATION
3. Data setting process:
1. Hold down the MODE button
reset AVG, DST, TM and MAX data from stored values to zero. (Fig. 6)
2. It cannot reset ODO, T-TM, T-ODO,
till the LCD digit is blanked, then release it. The computer will
•
A). The data is adjusted each digit separately. The setting digit is flickering.
4. Check relative position and gap of sensor and magnet periodically.
TM: Riding Time 0M00.0S-59M59.9S, 0.1 Second, 1H00M00S-99H59M59S, 1 Second, +/- 0.003%
1. The TM totals the riding time from the last RESET operation.
2. It will automatically begin counting upon
ding, and continue to count 2 seconds to confirm that no more wheel sensing signal is sent
when riding is stopped.
But this computer revises back the overcounted 4 seconds automatically.
3. It displays in 0.1 second increments when TM is less than 1 hour and changes to 1 second
increments after 1 hour. It will restart from zero after 100 hours.
B). Quickly press the MODE button •to increase the digital value by 1.
5. Clean the contacts of the bracket and the bottom of the main unit periodically.
6. Don’t use thinner, alcohol or benzine to clean the main unit or its accessories when they become dirty.
7. Remember to pay attention to the road while riding.
, DST/D.
C). To change the setting digit by hold down the MODE button •for more than 2 seconds.
D). Press the SET button
operation.
to store the data then change to the next setting or the normal
AUTOMATIC START/STOP
1. The computer will automatically begin counting data upon riding and stop counting data
„
Sensor: No Contact Magnetic Sensor.
Battery Type: 1.5V Battery X 1.(Typical No. LR44 / A76 / AG13 / V13GA.)
Battery Operating Life: About 2 years. (The original factory-attached battery may be shorter
than this period due to shipping and storage time.)
when riding is stopped.
WHEEL CIRCUMFERENCE
2. The flickering symbol "
" indicates that the computer is at start status.
1. Roll the wheel until the valve stem at its lowest point close to the ground, then mark this first
point on the ground. (Fig. a)
POWER AUTO ON/OFF
2. Get on the bike and have a helper push you until the valve stem returns to its lowest point.
Mark the second point on the ground. (Sitting on the bike achieves a more accurate reading
since the weight of the rider slightly changes the wheel circumference).
3. Measure the distance between the marks in milimeters. Enter this value to set the wheel
circumference.
Option: Get a suitable circumference value from the table. (Fig. b)
4. Adjust the wheel circumference as the data setting process.
5. Unit will change to the normal operation after this circumference setting.
To preserve battery, this computer will automatically switch off and just displays the "
it has not been used for about 4 minutes. The power will be turned on automatically by riding the
bike or by pressing the button.
" data when
Dimensions/Weight: 44.5 x 50.0 x 18mm / 25g
Wheel Circumference Setting: 1mm - 3999mm (1mm increment)
Operation Temperature: 0°C ~ 50°C (32°F ~ 122°F)
MAX: Maximum Speed
0.0–199.9Km/h (120.0 Mile/h), 0.1Km/h (Mile/h), +/- 1%
It shows the highest speed from the last RESET operation
DST/D: Distance Today
0.00–999.99Km (Miles), 0.01Km (Mile), +/- 0.01%
Storage Temperature: -10°C ~ 60°C (14°F ~ 140°F)
The DST/D function accumulates the distance data for one day rode. The data will be cleared at
AM 12:00:00 (0:00:00) automatically.
LOW BATTERY INDICATOR
1. The symbol "
" will appear to indicate the battery is nearly exhausted.
2. Replace battery with a new one within a few days after the symbol was appeared, otherwise the
stored data may be lost when the battery voltage is too low.
/
: Speed Pacer
It flashes the " " speed pacer arrow while the current speed is higher than the average speed
and flashes the " " conversely as long as the bike is being ridden.
Download from Www.Somanuals.com. All Manuals Search And Download.
|