OWNER'S MANUAL
ATSC TV/DVD COMBO
TCR13-A
TCR20-A
TCF20-A
POWER
TV/DTV
TV/AV
TV/DVD OPEN/CLOSE
Q.VIEW
INFO
MUTE
1
5
2
6
0
3
4
7
-
8
CC
9
SAP
P.MODE
CH+
VOL
_
MENU
VOL
+
OK
S.MODE
CH-
STOP
REV
SETUP PAUSE/STEP SUBTITLE
FWD
PREV
NEXT
A-B
D.MENU
REPEAT
PLAY/ENTER
SLOW
ANGLE
TITLE/PBC SEARCH
AUDIO PROGRAM ZOOM
D.CALL
GUIDE
10+
EXIT
ARC
CH.LIST FAV.LIST
Before operating the unit, please read this manual thoroughly.
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFEGUARDS
The lightning flash with arrowhead symbol, within an
equilateral triangle is intended to alert the user to the
presence of uninsulated dangerous voltage within the
product’s enclosure that may be of sufficient magnitude
to constitute a risk of electric shock.
CAUTION
RISK ELECTRIC SHOCK
DO NOT OPEN
!
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
!
the literature accompanying the appliance.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO
RAIN OR MOISTURE.
CAUTION: TO PREVENT ELECTRIC SHOCK DO NOT USE THIS POLARIZED PLUG WITH AN
EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES
CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.
CAUTION: These servicing instructions are for use by qualified service personnel
only. To reduce the risk of electric shock, do not perform any servicing other than
that contained inthe operating instructionsunless you arequalified to doso.
CAUTION: USE OF ANY CONTROLS, ADJUSTMENTS, ORPROCEDURES OTHER
THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION
EXPOSURE.
Important Safety Instructions
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the manufacturer's
instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. Apolarized plug
has two blades with one wider than the other. Agrounding type plug has two blades and a
third grounding prong. The wide blade or the third prong are provided for your safety. If the
provided plug does not fit into your outlet, consult an electrician for replacement of the
obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
11) Only use attachments/accessories specified by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table specified by
the manufacturer, or sold with the apparatus. When a cart is used,
use caution when moving the cart/Apparatus combination to avoid
injury from tip-over.
13) Unplug this apparatus during lightning storms or when unused for long periods of time.
14) Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is damaged,
liquid has been spilled or objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has been dropped.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Important safety Instructions
15) The apparatus shall notbe exposed todripping or splashingand that noobjects filled with
liquids, such asvases, shall beplaced on theapparatus.
16) The mains plug orappliance inlet isused as thedisconnect device, remainit readily
operable during theapparatus normal use.
17) POWER LINES
An outsideantenna system shouldnot be locatedin the vicinityof overhead powerlines or
other electric lightor power circuits, or where itcan fall ontoor against suchpower lines or
circuits. When installingan outside antennasystem, extreme careshould be takento keep
from touching suchpower lines orcircuits, as contactwith them mightbe fatal.
18) OVERLOADING
Do not overloadwall outlets andextension cords, asthis can resultin a riskof fire orelectric
shock.
19) OBJECT ANDLIQUID ENTRY
Do not pushobjects through anyopenings in thisunit, as theymay touch dangerousvoltage
points or shortout parts thatcould result infire or electricshock. Never spillor spray any
type of liquidinto the unit.
20) OUTDOORANTENNA GROUNDING
If an outsideantenna or cablesystem is connectedto the unit, be sure theantenna or cable
system is groundedto provide someprotection against voltagesurges and built-upstatic
charges, Section 810of the NationalElectrical Code (NEC), ANSI/NFPA70, provides
information with respectto proper groundingof the mastand supporting structure,
grounding of thelead-in wire toan antenna dischargeunit, size ofgrounding conductors,
location of antennadischarge unit, connectionto grounding electrodes, and requirements
for the groundingelectrode.
21) SERVICING
Do not attemptto service thisunit yourself asopening or removingcovers may exposeyou
to dangerous voltageor other hazards. Refer all servicingto qualified servicepersonnel.
22) DAMAGE REQUIRINGSERVICE
Unplug this unitfrom the walloutlet and referservicing to qualifiedservice personnel under
the following conditions:
a. When thepower-supply cord orplug is damaged.
b. If liquidhas been spilled, or objects havefallen into theunit.
c. If theunit has beenexposed to rainor water.
d. If theunit does notoperate normally byfollowing the operatinginstructions. Adjust
only those controlsthat are coveredby the operatinginstructions, as animproper
adjustment of othercontrols may resultin damage and will often requireextensive
work by aqualified technician torestore the unitto its normaloperation.
e. If theunit has beendropped or thecabinet has beendamaged.
f. When theunit exhibits adistinct change inperformance, this indicatesa need for
service.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Important safety Instructions
23) REPLACEMENT PARTS
When replacement parts are required, be sure the service technician uses replacement parts
specified by the manufacturer or those that have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock or other hazards.
24) SAFETY CHECK
Upon completion of any service or repairs to this unit, ask the service technician to perform
safety checks to determine that the unit is in proper operating condition.
25) HEAT
The product should be situated away from heat sources such as radiators, heat registers,
stoves, or other products (including amplifiers) that produce heat.
26)DISC SLOT
Keep your fingers well clear of the disc slot as it is closing. It may cause serious personal
injury.
27) CONNECTING
When you connect the product to other equipment, turn off the power and unplug all of the
equipment from the wall outlet. Failure to do so may cause an electric shock and serious
personal injury. Read the owner's manual of the other equipment carefully and follow the
instructions when making any connections.
28) SOUND VOLUME
Reduce the volume to the minimum level before you turn on the product. Otherwise, sudden
high volume sound may cause hearing or speaker damage.
29) SOUND DISTORTION
Do not allow the product output distorted sound for a longtime. It may cause speaker
overheating and fire.
30) LASER BEAM
Do not look into the opening of the disc slot or ventilation opening of the product to see the
source of the laser beam. It may cause sight damage.
31) DISC
Do not use a cracked, deformed, or repaired disc. These discs are easily broken and may
cause serious personal injury and product malfunction.
32) NOTE TO CABLE TV SYSTEM INSTALLER
This reminder is provided to call the Cable TV system installer's attention to Article 820-40 of
the NEC that provides guidelines for proper grounding and, in particular, specifies that the
cable ground shall be connected to the grounding system of the building, as close to the point
of cable entry as practical.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Antenna connection
If the picture is not clear or is snowy, it is recommended that an External Aerial
is used, this is usually mounted outside.
300 twin-lead cable
Antenna adapter
(Not supplied)
Aerial input
75 standard
coaxial type
75 coaxial cable
Plug
(Not supplied)
AC power socket
Note:
* It is recommended that a 75 ohm coaxial antenna is used to avoid
interference.
*To avoid interference from electrical signals, do not bind the antenna
cable together with any mains lead.
Preparation for the remote control
Battery installation
Remove the battery cover.
Insert two size AA batteries matching
the +/-polarities of the battery to the +/-
marks inside the battery compartment.
Tips for remote operation
When the remote control will not be used for a long period of time or when the
batteries are worn out, remove the batteries to prevent leakage.
Do not throw the batteries into fire. Dispose of used batteries in the specified
manner.
Do not drop, dampen or disassemble the remote control.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts and functions
Front panel the TV set
POWER
Power Indicator
Signal Receiver
Power Switch
The DVD Player
TCR13-A
Play
the DVD
Channel Position
up/down
Menu
Video
R/L
Audio
TV/AV/DVD
Switching
Stop
the DVD
Open/close
the DVD
Volume up/ down
TCR20-A
TCF20-A
Video
R/L
Audio
Earphone
Rear panel of the TV set
COMPONENT
Cb
Cr
Video Y input terminal
Video output terminal
Y
Video Cb inputterminal
Video Cr inputterminal
Antenna input socket
OUT
Audio right channeloutput terminal
Audio left channeloutput
terminal
IN
Audio right channelinput terminal
Audio left channelinput terminal
VIDEO1
L
R
Video 1
AUDIO1
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Remote Control
Buttons on the remote control
Power Switch
Open/close DVD Tray
POWER
TV/DTV
TV/AV
TV/DVD OPEN/CLOSE
TV / AV Mode Selection
TV / DTV Mode Selection( The function is not available)
TV / DVD Mode Selection
Mute Sound
Q.VIEW
INFO
MUTE
Q.VIEW button: Return to Previous Channel
On Screen Display
1
5
2
6
0
3
4
Channel / Track Selection
SAP button: Second Audio Program
7
-
8
CC
CC Mode Selection: Closed captioning (selects mode).
- button: select additional channels being broadcasted.
For example, to select channel “54-3”, press “54”, “-”, “3”,
and then press “OK”.
9
SAP
P.MODE
CH+
P.MODE (picture mode):Adjust Picture Mode
Volume/Channel Adjusting
Go to TV Menu
VOL
_
MENU
VOL
+
Exit On Screen Display
OK
SLEEP
GUIDE
TV Sleep button
CH-
CH.LIST (channel list)
CH.LIST FAV.LIST
SIZE
GUIDE reference (may not operate using some systems)
FAV.LIST (favorite list) Enter
SIZE: Aspect Ratio Control under 16:9 digital signal input
DVD STOP Playback
PAUSE/STEP SUBTITLE
SETUP
FWD
STOP
REV
PREV
NEXT
A-B
DVD SETUP
DVD FAST REVERSE
D.MENU
REPEAT
DVD CAPTION (SUBTITLE) Selection
DVD PAUSE/STEP
SLOW
PLAY/ENTER
DVD PREVIOUS Chapter / Track
DVD FAST FORWARD
TITLE/PBC SEARCH
ANGLE
DVD NEXT Chapter / Track
DVD MENU
AUDIO PROGRAM ZOOM
D.CALL
DVD A-B REPEAT
DVD Playback / Confirm Menu Selection
UP
DVD REPEAT Mode
10+
CLR
LEFT
RIGHT
DVD Cursor Move button
DVD SLOW
DOWN
DVD ANGLE Change
DVD SEARCH
DVD TITLE
DVD AUDIO Mode
DVD INFORMATION
DVD PROGRAM
Zoom Function
10+
CLR: clear
7
Download from Www.Somanuals.com. All Manuals Search And Download.
The other video and audio equipment Connections
You can connect the DVD,VCR and stereo system to the output to enjoy a
higher quality of picture and sound effect.
ANT IN
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Antenna connections
Ifyouareusinganindoororoutdoorantenna,followtheinstructionsbelowthatcorrespondtoyourantenna
system. If you are using a cable TV service (CABLE), see the Cable TV connections.
Combination VHF/UHF antenna (Single 75 ohm cable or 300 ohm twin-lead wire)
Connect the 75 ohm cable from the combination
VHF/UHF antenna to the RF IN jack.
RF IN
jack
RF IN
jack
If using aflat UHF 300ohm twin-lead wire,
connect these flatwires to anoptional 75/300
ohm matching transformer/adapter(available
at many retailers), and then connectthe
adapter to the'RF' IN connectoron the back
of the television.
75 ohm
coaxial
cable
300-75 ohm
matching
transformer
Combination VHF/UHF antenna (Separate VHF and UHF 300 ohm twin-lead wires)
Connect the UHF 300 ohm twin-lead wire to the
combiner (not supplied). Connect the VHF 300
300-75 ohm
matching
transformer
RF IN
jack
ohm twin-lead wire to the 300-75 ohm matching
transformer. Attachthetransformertothecombiner,
then attach the combiner to the RF IN jack.
Combiner
UHF 300 ohm
VHF 300 ohm
Separate VHF/UHF antennas (75 ohm VHF cable and 300 ohm UHF twin-lead wires)
Connect the VHF 75 ohm cable and UHF 300 ohm
twin-lead wire to the combiner. Attach the combiner
to the RF IN jack.
RF IN
jack
VHF 75 ohm
Combiner
UHF 300 ohm
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Cable TV connections
This unit has an extended tuning range and can tune most cable channels without using a CableTV
Converter box. Some cable companies offer "premium pay channels" in which the signal is
scrambled. Descrambling these signals for normal viewing requires the use of a descrambler device
which is generally provided by the cable company.
FOR SUBSCRIBERS TO BASIC CABLE TV SERVICE
For basic cable service not requiring a Converter/Descrambler
RF IN
box, connect the 75 ohm Coaxial Cable directly to the RF IN
jack
Jack on the back of the unit.
75 ohm
coaxial cable
FOR SUBSCRIBERS TO SCRAMBLED CABLE TV SERVICE
If you subscribe to a cable TV service which requires the use of a converter/descrambler box, connect the
incoming 75 ohm coaxial cable to the converter/descrambler box. Using another 75 ohm coaxial cable, connect
the output jack of the converter/descrambler box to the RF IN jack on the unit. Follow the connections shown
below. Set the unit to the output channel of the converter/descrambler box (usually channel 3 or 4) and use the
converter/descrambler box to select channels.
Incoming
75 ohm
cable TV cable
RF IN
jack
75 ohm cable to
unit
Converter/
descrambler
FOR SUBSCRIBERS TO UNSCRAMBLED BASIC CABLE TV SERVICE WITH
SCRAMBLED PREMIUM CHANNELS
If you subscribe to a cable TV service in which basic channels are unscrambled and premium channels require the
use of a converter/descrambler box, you may wish to use a signal splitter and an A/B switch box (available from the
cable company or an electronics supply store). Follow the connections shown below. With the switch in the "B"
position, you can directly tune any nonscrambled channels on your unit. With the switch in the "A" position, tune your
unit to the output of the converter/descrambler box (usually channel 3 or 4) and use the converter/descrambler box
to tune scrambled channels.
Incoming
75 ohm
cable TV cable
Converter/
descrambler
RF IN
jack
75 ohm cable
to unit
A
Splitter
A/B switch
B
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections for other equipment
Using the audio/video inputs
If you connect the TV to a camcorder or Video Game, you can select different modes by pressing
TV/AV.
Press TV/AV repeatedly to select the desired mode.
"AV1", "AV2" ,"COMPONENT","DVD" or TV channel will display on the screen for 4 seconds, No signal
will be displayed on the screen when there is no signal input.
AV 1
AV1
AV2
COMPONENT DVD
TV Channel
To connect the TV to a camcorder
To playback from the camcorder, connect the camcorder to the unit as shown.
Camcorder
Front of TV
VIDEO IN
To Audio/Video OUT
AUDIO IN (R)
AUDIO IN (L)
Audio/Video cord (not supplied)
To connect the TV to a Video Game
The TV can also be used as a display device for many video games. However, due to the wide variety
of formats, they have not all been included in the suggested connection diagram. Youl need to consult
each component's Owner's Manual for additional information.
Front of TV
VIDEO IN
Video Game
AUDIO IN (R)
To Audio/Video OUT
AUDIO IN (L)
Audio/Video cord (not supplied)
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the language and blue screen
You can choose from three different
languages (English, French and
Spanish) for the on-screen displays.
SETTING THE LANGUAGE
1 Press POWER ( ) toturn on the TV.
FUNCTION
POWER
TV/DTV
TV/AV
TV/DVD OPEN/CLOSE
LANGUAGE
ENGLISH
ON
CC1
BLUE SCREEN
NTSC CAPTION
DTV CAPTION
Q.VIEW
INFO
MUTE
2 Press MENU, and then
1
5
2
6
0
3
4
press VOL+/- button to
select FUNCTION menu,
then press CH- button to
enter.
PARENTAL LOCK
7
-
8
CC
9
SAP
P.MODE
CH+
VOL
_
MENU
VOL
+
OK
SLEEP
GUIDE
CH-
3 Press CH+/- button to select the LANGUAGE option,
then press VOL+/- to select the desired language:
English, Spanish orFrench.
CH.LIST FAV.LIST
SIZE
SETUP PAUSE/STEP SUBTITLE
STOP
REV
PREV
FWD
NEXT
4 Press MENU until the MENU screen disappears.
D.MENU
A-B
REPEAT
SLOW
PLAY/ENTER
ANGLE
TITLE/PBC
SEARCH
D.CALL
AUDIO PROGRAM ZOOM
SETTING THE BLUE SCREEN
10+
CLR
1 Press MENU, and then
press VOL+/- button to
FUNCTION
LANGUAGE
ENGLISH
ON
CC1
select FUNCTION menu,
then press CH- button to
enter.
BLUE SCREEN
NTSC CAPTION
DTV CAPTION
PARENTAL LOCK
2 Press CH+/- button to select the BLUE SCREEN option,
then press VOL+/- to select OFF or ON.
3 Press MENU until the MENU screen disappears.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Channel menu
This describes the case for searching and memorizing channels for DTV/ATV.
AUTO SCAN (DTV/ATV)
(When using antenna)
The channels broadcasted in DTV and ATV are
automatically scanned and memorized. Only the
receivable channels in the area where this TV is
used will be memorized.
POWER
TV/DTV
TV/AV
TV/DVD OPEN/CLOSE
Q.VIEW
INFO
MUTE
1
5
2
6
0
3
4
AUTO SCAN (CATV)
(When using basic cable)
The channels broadcasted in CATV are automatically
scanned and memorized.
7
-
8
CC
9
SAP
P.MODE
CH+
NOTE:
Be sure thatantenna or cableis connected properlybefore plugging the
power cord.
VOL
_
MENU
VOL
+
OK
SLEEP
GUIDE
CH-
CH.LIST FAV.LIST
SIZE
1 Press MENU, and then press VOL+/- button to select
CHANNEL menu, then press CH- button to enter.
SETUP PAUSE/STEP SUBTITLE
STOP
REV
PREV
FWD
NEXT
2 Press CH+/- button to
select the RECEPTION
option.
CHANNEL
D.MENU
A-B
REPEAT
CHANNEL NO .
TUNER
SKIP
2.1
ANTENNA
OFF
SLOW
PLAY/ENTER
ANGLE
TITLE/PBC
SEARCH
D.CALL
AUTO SCAN
AUDIO PROGRAM ZOOM
3 Press VOL +/- button
to select AIR/ CABLE.
10+
CLR
4 Press CH +/- button
to select AUTO SCAN option.
5 Press VOL+ button to start scanning.
When you press VOL+ on the remote control,
scanning the channels in both analog and digital
modes will automatically start.
When scanning is completed, the memorized
smallest channel will be displayed.
When you press the MENU button while scanning, the
scanning is interrupted and the lowest memorized
channel is displayed.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Channel menu
SETTING SKIP
After the programs are preset, you can skip some
programs to select your favorite channels only.
1 Press MENU, and then
CHANNEL
press VOL+/- button to
select CHANNEL menu, CHANNEL NO .
2.1
ANTENNA
OFF
POWER
TV/DTV
TV/AV
TV/DVD OPEN/CLOSE
TUNER
SKIP
AUTO SCAN
then press CH- button to
enter.
Q.VIEW
INFO
MUTE
1
5
2
6
0
3
4
2 Press CH+/- button to
select the SKIP option,
then press VOL+/- button
to select ON or OFF.
7
-
8
CC
9
SAP
P.MODE
CH+
VOL
_
MENU
VOL
+
NOTE: When tuning DTV channels and no signal is present,
the SKIP-over option will be available.
OK
SLEEP
GUIDE
CH-
CH.LIST FAV.LIST
SIZE
SETUP PAUSE/STEP SUBTITLE
If you wantto recover the skipped channel
STOP
REV
PREV
FWD
NEXT
1. Use Direct-digit Choosing button to select the number
of the channel to be recovered.
2. Do the above steps again.
D.MENU
A-B
REPEAT
SLOW
PLAY/ENTER
3. Press VOL+/- button to set SKIP as Off.
ANGLE
TITLE/PBC
SEARCH
D.CALL
AUDIO PROGRAM ZOOM
10+
CLR
SETTING COLOR SYSTEM(only in ATV mode)
1 Press MENU, and then
CHANNEL
press VOL+/- button to
CHANNEL NO .
TUNER
SKIP
2.1
ANTENNA
OFF
select CHANNEL menu,
then press CH- button to
enter.
AUTO SCAN
2 Press CH+/- button to
select the COLOR
SYSTEM option, then
press VOL+/- button
to select AUTO or NTSC.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Channel selection
You can select the channel by using either CH +/- button
or Channel number buttons. How to select the channel
in each way is shown below.
1 Using CH +/- button
TV/DVD OPEN/CLOSE
POWER
TV/DTV
TV/AV
Using CH +/- button on the remotecontrol, change thechannel.
Same operation isavailable with CH +/- button on the frontpanel
of the mainunit.
Q.VIEW
INFO
MUTE
1
5
2
6
0
3
4
Press the Direct Channel selection buttons to select the channel.
2
7
-
8
CC
Antenna Mode Direct Channel Selection
When the Antenna/Cable menu option is in the Antennaposition, all channels
can be instantly selected by using
9
SAP
P.MODE
digits button. For example:
CH+
2-9: Press 2-9 as needed.
Example, to select channel 2, press"2".
10-69: Press the 2 digits inorder. If you select the channel higherthan 69,
the channel will not change, becauseit is not available.
VOL
_
MENU
VOL
+
OK
SLEEP
GUIDE
CH-
CH.LIST FAV.LIST
SIZE
CABLE Mode Direct Channel Selection
When the Antenna/Cable menu option is in the Cable position, channels
can be selected as follows:
SETUP PAUSE/STEP SUBTITLE
STOP
REV
PREV
FWD
NEXT
1-9: Press 1-9 asneeded. Example, to selectchannel 2,
press "2".
D.MENU
A-B
REPEAT
10-99: Press the 2digits in order. Example, to select channel 32,
press "3" then "2".
100-125: Press the digital1 button, the "1--"will appear
on the screen, thenpress the 2 digitsof remain in order.
SLOW
PLAY/ENTER
ANGLE
TITLE/PBC
SEARCH
D.CALL
CABLE
TV
AUDIO PROGRAM ZOOM
VHF
2-13
VHF
2-13
10+
CLR
UHF
14-69
STD/HRC/IRC
14-36
(A) (W)
37-59
(AA) (WW)
60-85
(AAA) (ZZZ)
86-94
(86) (94)
95-99
(A-5) (A-1)
100-125
(100) (125)
01
(5A)
NOTE:
In the DTV broadcasting, one channel sometimes broadcasts
multiple programs depending on the air time. In this case, the
main channel is called major channel and the sub channel is
called minor channel.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Volume adjustment
This section describes how to adjust the volume when
viewing TV. The MUTE function, which is useful when
you have a visitor or a phone call, will be also described.
1 Using VOL +/- button
You can adjust theaudio volume withVOL +/- button on
the remote control.
POWER
TV/DTV
TV/AV
TV/DVD OPEN/CLOSE
Q.VIEW
INFO
MUTE
The volume bar is displayed at the bottom of the screen
when adjusting the volume.
Same operation isavailable with VOL +/- on the front
panel of themain unit.
1
5
2
6
0
3
4
7
-
8
CC
9
SAP
P.MODE
CH+
2 Using MUTE button
Press MUTE button on the remote control to mute the
sound.
The MUTE sign is displayed on the screen while muting.
VOL
_
MENU
VOL
+
OK
SLEEP
GUIDE
CH-
CH.LIST FAV.LIST
SIZE
SETUP PAUSE/STEP SUBTITLE
STOP
REV
To release theMUTE status, press MUTE button again
or press VOL+ button.
PREV
FWD
NEXT
MUTE will displayedcontinuously when CCis OFF, MUTE
will disappear 5 seconds later when CC is ON.
D.MENU
A-B
REPEAT
SLOW
PLAY/ENTER
ANGLE
TITLE/PBC
SEARCH
D.CALL
SWITCHING AUDIO
This section describes how to switch the audio language
in the digital mode.
AUDIO PROGRAM ZOOM
10+
CLR
2 Switch the audio language.
When you pressSAP button on the remote control, the
currently selected language and the number of received
languages will be displayed on the screen.
Every time you press SAP button on the remote control,
the language will be switched.
Languages you can switch differ depending on the
receiving broadcast.
NOTE:
Pressing the SAPbutton works only with some TV channels,
and does not work with external equipment such as DVD players.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Screen information
You can display the currently selected channel number or
other information such as the audio mode on the screen
for checking.
In the analog mode, the currently selected channel
number and the audio mode are displayed.
1 Display the channel number and the audio mode.
Press INFO button on the remote control.
The currently selected channel number and the audio
mode are displayed at the top right of the screen.
POWER
TV/DTV
TV/AV
TV/DVD OPEN/CLOSE
Q.VIEW
INFO
MUTE
1
5
2
6
0
3
4
13
AUTO
7
-
8
CC
9
SAP
P.MODE
CH+
To clear thedisplay, press INFO button again.
VOL
_
MENU
VOL
+
In the digitalmode, the detailedinformation for the
currently selected channel such as the program
GUIDE is displayed.
OK
SLEEP
GUIDE
CH-
CH.LIST FAV.LIST
SIZE
SETUP PAUSE/STEP SUBTITLE
STOP
REV
Display the detailed information for the channel.
Every time you press INFO button, the display mode
will be switched as below.
PREV
FWD
NEXT
D.MENU
A-B
REPEAT
SLOW
PLAY/ENTER
14.1
DTV-AIR
5
11-1
MBC DTV
NO PROGRAM INFO
NO CC INFORMATION UNKNOWN
NO RATING 07:19-09:56
[1920*1080]
6
7
8
9
10
1
2
3
4
ANGLE
TITLE/PBC
SEARCH
D.CALL
16:9
AUDIO PROGRAM ZOOM
NO PROGRAM INFORMATION
IS AVAILABLE
10+
CLR
The following information is displayedin the INFOmode.
(1) Channel title
(6) Resolution
(7) Zoom
(8) Audio language
(9) Program air time
(10) Program content
(2) Program content
(3) Closed caption
(4) Channel title
(5) Channel number
NOTES:
When the program guide is displayed in more than 6 lines, useVOL+/-
button and scroll for reading.
"No description provided" is displayed when the program guide is not
provided.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Video menu
SETTING VIDEO
1 Press MENU button. The main menu screen will appear.
2 Press VOL+/- button to
select VIDEO Option,
then press CH- button
to enter.
VIDEO
POWER
TV/DTV
TV/AV
TV/DVD OPEN/CLOSE
CONTRAST
BRIGHTNESS
SHARPNESS
COLOR
80
80
50
50
Q.VIEW
INFO
MUTE
1
5
2
6
0
3
4
TINT
+00
7
-
8
CC
9
SAP
P.MODE
3 Press CH+/- to select the desired option, then press
VOL+/- to adjust.
CH+
VOL
_
MENU
VOL
+
OK
SLEEP
GUIDE
CH-
CH.LIST FAV.LIST
SIZE
Contrast
This will adjustthe intensity ofbright parts inthe picture butkeep
the dark partsunchanged.
SETUP PAUSE/STEP SUBTITLE
STOP
REV
PREV
FWD
NEXT
D.MENU
A-B
REPEAT
Brightness
This will adjustthe light outputof the completepicture, which will
mainly affect the darker areasof the picture.
SLOW
PLAY/ENTER
ANGLE
TITLE/PBC
SEARCH
D.CALL
Color
This will adjustthe saturation levelof the colorsto suit your
personal preference.
AUDIO PROGRAM ZOOM
10+
CLR
Sharpness
This will adjustthe sharpness offine details inthe picture.
Tint
Allows you toselect the colormix (Tint) of the picture.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Audio menu
SETTING AUDIO
1 Press MENU button. The main menu screen will appear.
2 Press VOL+/- button to
AUDIO
select AUDIO Option,
POWER
TV/DTV
TV/AV
TV/DVD OPEN/CLOSE
then press CH- button
to enter.
VOLUME
BALANCE
80
+00
Q.VIEW
INFO
MUTE
1
5
2
6
0
3
4
7
-
8
CC
9
SAP
3 Press CH+/- to select
the desired option, then
press VOL+/- to adjust.
P.MODE
CH+
VOL
_
MENU
VOL
+
OK
SLEEP
GUIDE
Volume
This will adjustthe sound outputlevel.
CH-
CH.LIST FAV.LIST
SIZE
SETUP PAUSE/STEP SUBTITLE
STOP
REV
PREV
FWD
NEXT
Balance
This will adjustthe sound outputbalance.
D.MENU
A-B
REPEAT
SLOW
PLAY/ENTER
ANGLE
TITLE/PBC
SEARCH
D.CALL
AUDIO PROGRAM ZOOM
10+
CLR
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Manual time setting
EXAMPLE: Setting the time to "8:30AM"
You must set the time manually
for ON/OFF Timer.
TO SET TIME
1 Press MENU. The main menu screen will appear.
2 Press VOL+/- button to
select TIME option,
then press CH- button
to enter the submenu.
TIME
POWER
TV/DTV
TV/AV
TV/DVD OPEN/CLOSE
TIME
--:-- AM
--:-- AM
--:--AM
ON
Q.VIEW
INFO
MUTE
TIMER ON
TIMER OFF
DAYLIGHT SAVING
TIME ZONE
1
5
2
6
0
3
4
CENTRAL
7
-
8
CC
3 Press CH+/- button to
select TIME, then press
CH+/- button to select
"--:--","AM";
press VOL+/- button to
set the value & AM &PM.
9
SAP
P.MODE
CH+
VOL
_
MENU
VOL
+
OK
SLEEP
GUIDE
CH-
CH.LIST FAV.LIST
SIZE
SETUP PAUSE/STEP SUBTITLE
STOP
REV
4 Press MENU until the MENU screen disappears.
PREV
FWD
NEXT
D.MENU
A-B
REPEAT
SLOW
PLAY/ENTER
ANGLE
TITLE/PBC
SEARCH
D.CALL
AUDIO PROGRAM ZOOM
10+
CLR
NOTE:
After apower failure ordisconnection of thepower, the
time will getlost. In thiscase, reset thepreset time.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the ON/OFF timer
This feature allows you to have the
SETTING THE TIMER ON
TV automatically turn on/off at a
predetermined time. If you program
1 Press MENU. The main menu screen will appear.
the ON/OFF TIMER, the TV will turn
on/off at the time your predetermined
time.
2 Press VOL+/- button to
select TIME option,
then press CH- button
to enter the submenu.
TIME
POWER
TV/DTV
TV/AV
TV/DVD OPEN/CLOSE
TIME
--:-- AM
--:-- AM
--:-- AM
ON
Q.VIEW
INFO
MUTE
TIMER ON
TIMER OFF
DAYLIGHT SAVING
TIME ZONE
1
5
2
6
0
3
4
3 Press CH+/- button to
select TIME ON, then
press CH+/- button to
select "--:--","AM";
press VOL+/- button to
set the value.
CENTRAL
7
-
8
CC
9
SAP
P.MODE
CH+
VOL
_
MENU
VOL
+
OK
SLEEP
GUIDE
CH-
4 Press MENU until the MENU screen disappears.
CH.LIST FAV.LIST
SIZE
SETUP PAUSE/STEP SUBTITLE
STOP
REV
PREV
FWD
NEXT
D.MENU
A-B
REPEAT
SETTING THE TIMER OFF
SLOW
PLAY/ENTER
1 Press MENU. The main menu screen will appear.
ANGLE
TITLE/PBC
SEARCH
D.CALL
AUDIO PROGRAM ZOOM
2 Press VOL+/- button to
select TIME option,
10+
TIME
CLR
then press CH- button
to enter the submenu.
TIME
--:-- AM
--:-- AM
--:-- AM
ON
TIMER ON
TIMER OFF
DAYLIGHT SAVING
TIME ZONE
CENTRAL
3 Press CH+/- button to
select TIME OFF, then
press CH+/- button to
select "--:--","AM";
press VOL+/- button to
set the value.
4 Press MENU until the MENU screen disappears.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Function menu
SETTING THE NTSC CAPTION
This allows you to configure the way you choose to view
the captioning.
1. Press the MENU button and thenuse VOL+/- button to selectthe
FUNCTION menu.
POWER
TV/DTV
TV/AV
TV/DVD OPEN/CLOSE
Q.VIEW
INFO
MUTE
2. Press CH- button to enter,
then press CH+/- button
to select NTSC CAPTION.
FUNCTION
1
5
2
6
0
3
4
LANGUAGE
ENGLISH
ON
CC1
7
-
8
CC
BLUE SCREEN
NTSC CAPTION
DTV CAPTION
PARENTAL LOCK
3.Then use VOL+/- button to
select caption: OFF,C1, C2,
C MUTE,TEXT1, TEXT2.
9
SAP
P.MODE
CH+
You can also pressCC
button on theremote
control to selectthe
desired caption.
VOL
_
MENU
VOL
+
OK
SLEEP
GUIDE
CH-
CH.LIST FAV.LIST
SIZE
SETUP PAUSE/STEP SUBTITLE
STOP
REV
4. When you are satisfied with
your choice, press MENU
button to return to the
previous menu.
PREV
FWD
NEXT
D.MENU
A-B
REPEAT
SLOW
PLAY/ENTER
TITLE/PBC
SEARCH
D.CALL
CAPTION
ANGLE
The term for the words that scroll across the bottom of the TV
screen; usually the audio portion of the program provided for
the hearing impaired.
AUDIO PROGRAM ZOOM
10+
CLR
TEXT
The term forthe words thatappear in alarge black frameand
almost cover theentire screen; usuallymessages provided by
the broadcaster.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Function menu
An age limitation can be set to
forbid children to see and hear
violent scenes or pictures for
TO REGISTER PASSWORD
1 Press MENU. The main menu screen will appear.
adults, etc. The TV Corresponds
to "TV RATING" and "MOVIE RATING".
to use theparental control function,
you must register a password.
2 Press VOL+/- to
FUNCTION
select FUNCTION,
then press CH- to
enter the submenu.
LANGUAGE
ENGLISH
ON
CC1
POWER
TV/DTV
TV/AV
TV/DVD OPEN/CLOSE
BLUE SCREEN
NTSC CAPTION
DTV CAPTION
PARENTAL LOCK
Q.VIEW
INFO
MUTE
1
5
2
6
0
3
4
7
-
8
CC
3 Press CH+ to select
PARENTAL LOCK,
then press VOL+ to
enter the submenu.
9
SAP
P.MODE
CH+
PLEASE ENTER PASSWORD
VOL
_
MENU
VOL
+
OK
SLEEP
GUIDE
CH-
CH.LIST FAV.LIST
SIZE
4 Enter the password (4
digits) using thenumber
buttons(0-9).
SETUP PAUSE/STEP SUBTITLE
STOP
REV
PREV
FWD
NEXT
The TV is set up with the
initial password 0000.
D.MENU
A-B
REPEAT
PARENTAL LOCK
SLOW
PLAY/ENTER
MPAARATING
TITLE/PBC
SEARCH
D.CALL
ANGLE
PARENTAL GUIDE
CA ENG RATING
CA FREN RATING
DOWN LOAD RATING
PARENTAL LOCK
AUDIO PROGRAM ZOOM
5 After inputting password
accurately, Press CH+/-
to select thedesired item.
10+
CLR
ON
CHANGE PASSWORD
NOTES:
If you forget the password, you cannot set the Parent Control.
To avoid forgetting thepassword, write itdown and keepit in a
safe place.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Function menu
TO CHANGE PASSWORD
1 Press MENU. The main menu screen will appear.
2 Press VOL+/- to select
FUNCTION, then press
CH- to enter the submenu.
FUNCTION
LANGUAGE
ENGLISH
ON
CC1
POWER
TV/DTV
TV/AV
TV/DVD OPEN/CLOSE
BLUE SCREEN
NTSC CAPTION
DTV CAPTION
Q.VIEW
INFO
MUTE
3 Press CH+ to select
PARENTAL LOCK
PARENTAL LOCK,
then press VOL+ to
enter the submenu.
1
5
2
6
0
3
4
7
-
8
CC
9
SAP
P.MODE
PLEASE ENTER PASSWORD
CH+
4 Enter the password (4
digits) using the number
buttons(0-9).
----
VOL
_
MENU
VOL
+
OK
SLEEP
GUIDE
CH-
CH.LIST FAV.LIST
SIZE
SETUP PAUSE/STEP SUBTITLE
STOP
REV
4 Press CH+ to select
CHANGE PASSWORD,
then press VOL+ to
enter the submenu.
PREV
FWD
NEXT
PARENTAL LOCK
D.MENU
A-B
MPAARATING
REPEAT
PARENTAL GUIDE
CA ENG RATING
CA FREN RATING
DOWN LOAD RATING
PARENTAL LOCK
CHANGE PASSWORD
SLOW
PLAY/ENTER
SEARCH
D.CALL
ANGLE
TITLE/PBC
ON
AUDIO PROGRAM ZOOM
5 Enter the new password using
the number buttons(0-9).
10+
CLR
NEW PASSWORD
0000
6 Enter again the new password.
NOTES:
If you forget the password, you
cannot set the Parent Control.
To avoid forgetting the password,
write it down and keep it in a safe
place.
7 Press MENU until the MENU screen disappears.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Function menu
TO SET PARENTAL CONTROL ON/OFF
1 Enter the PARENT CONTROL menu.
2 Press CH+/- button to
PARENTAL LOCK
select PARENTAL LOCK,
press VOL+/- button to
set ON or OFF.
POWER
TV/DTV
TV/AV
TV/DVD OPEN/CLOSE
MPAARATING
PARENTAL GUIDE
CA ENG RATING
CA FREN RATING
DOWN LOAD RATING
PARENTAL LOCK
CHANGE PASSWORD
Q.VIEW
INFO
MUTE
3 When you are satisfied
with your choice, press
MENU button to returnto
the previous menu.
1
5
2
6
0
3
4
ON
7
-
8
CC
9
SAP
P.MODE
CH+
TO SET PARENTAL GUIDE
VOL
_
MENU
VOL
+
1 Enter the PARENT CONTROL menu.
OK
SLEEP
GUIDE
CH-
2 Press CH+/- button to
PARENTAL LOCK
CH.LIST FAV.LIST
SIZE
select PARENTAL GUIDE,
press VOL+ button to
enter the submenu.
MPAARATING
SETUP PAUSE/STEP SUBTITLE
STOP
REV
PARENTAL GUIDE
CA ENG RATING
CA FREN RATING
DOWN LOAD RATING
PARENTAL LOCK
CHANGE PASSWORD
PREV
FWD
NEXT
D.MENU
A-B
REPEAT
3 Press CH+/-/VOL+/- button
to set the desired ratings.
ON
SLOW
PLAY/ENTER
ANGLE
TITLE/PBC
SEARCH
D.CALL
4 When you are satisfied
with your choice, press
MENU button to returnto
the previous menu.
PARENTAL GUIDE
AUDIO PROGRAM ZOOM
ALL FV
D
L
S
V
10+
CLR
NONE
TV-Y
TV-Y7
TV-G
Ratings for Television programs
including made-for-TV movies: TV-PG
TV-Y (Allchildren)
TV-14
TV-Y7 (Children7 years older)
TV-G (Generalaudience)
TV-MA
TV-PG (Parentalguidance suggested)
TV-14 (Parentsstrongly cautioned)
TV-MA (Mature audience only)
To use the TV after Parent Control is
activated.
TV Rating Children:
ALL (Age) (applies to TV-Y,TV-Y7)
When the program applied to theParental
Control setting is received, enter the
password. When the password is entered
correctly the protection will be temporarily
overridden.
FV (Fantasy Violence)(applies to TV-Y7)
TV Rating General:
ALL (Age)
(applies to TV-G, TV-PG,TV-14, TV-MA)
D (Dialogue - sexual dialogue) (applies to TV-PG,TV-14)
NOTE:
The Parental Control function is activated only on
programs and tapes that support the rating.
L (Language -adult language) (applies toTV-PG, TV-14, TV-MA)
S (Sex - sexual situations)
V (Violence)
(applies toTV-PG, TV-14, TV-MA)
(appliesto TV-PG,TV-14, TV-MA)
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Function menu
TO SET THE MPAARATING
1 Enter the PARENT CONTROL menu.
PARENTAL LOCK
2 Press CH+/- button to
select MPAA RATING,
then press VOL+ button
to enter the submenu.
MPAARATING
PARENTAL GUIDE
CA ENG RATING
CA FREN RATING
DOWN LOAD RATING
PARENTAL LOCK
CHANGE PASSWORD
POWER
TV/DTV
TV/AV
TV/DVD OPEN/CLOSE
Q.VIEW
INFO
MUTE
ON
1
5
2
6
0
3
4
7
-
8
CC
3 Press CH+/- button to select
the desired rating.
9
SAP
P.MODE
CH+
Rating for Moviespreviously shown intheaters:
VOL
_
MENU
VOL
+
Movie Rating
NR
G
(Permits all programs)
(General audience)
OK
MPAA RATING
SLEEP
GUIDE
CH-
N/A
G
PG
PG-13
R
PG
(Parental guidance suggested)
CH.LIST FAV.LIST
SIZE
PG-13 (Parents strongly cautioned)
(Restricted)
NC-17 (No one 17 and under admitted)
(Adult only)
SETUP PAUSE/STEP SUBTITLE
STOP
REV
R
PREV
FWD
NEXT
X
NC-17
X
D.MENU
A-B
REPEAT
If you setPG-13 : Gand PG movies
will be available , PG-13, R, NC-17
and X will be blocked.
SLOW
PLAY/ENTER
ANGLE
TITLE/PBC
SEARCH
D.CALL
AUDIO PROGRAM ZOOM
10+
CLR
4 Press VOL+/- button to select delete or
.
5 Press MENU until the MENU screen disappears.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Closed caption
WHAT IS CLOSED CAPTIONING?
This television has the capability to decode and display closed captioned television programs. Closed captioning
will display text on the screen for hearing impaired viewers or it will translate and display text in another language.
Captions: This closed caption mode will display text on the
screen in English or another language (depending on the set-
ting of the closed captions).
POWER
TV/DTV
TV/AV
TV/DVD OPEN/CLOSE
Generally, closed captions in English are transmitted on captions
CC 1 and closed captions in other languages are transmitted on
Captions CC 2.
Q.VIEW
INFO
MUTE
1
5
2
6
0
3
4
Text: The text closed caption mode will usually fill the screen
with a programming schedule or other information.
7
-
8
CC
After selecting a closed caption mode, it will stay in effect until it
is changed, even if the channel is changed.
9
SAP
P.MODE
If the captions signal is lost due to a commercial or a break in
the signal, the captions will reappear when the signal is received
again. If the channels are changed, the captions will be delayed
approximately 10 seconds. The captions will appear in places
on the screen where they will least interfere with the picture,
usually on the bottom of the screen. News programs will usually
show three-line closed captions which scroll onto the screen.
Most other shows provide two or three lined captions placed
near the character who is speaking so the viewer can follow the
dialogue. Words in italics or underlined describe titles, words in
foreign languages or words requiring emphasis. Words that are
sung usually appear enclosed by musical notes.
CH+
VOL
_
MENU
VOL
+
OK
SLEEP
GUIDE
CH-
CH.LIST FAV.LIST
SIZE
SETUP PAUSE/STEP SUBTITLE
STOP
REV
PREV
FWD
NEXT
D.MENU
A-B
REPEAT
For television programs broadcasting with closed captions, look
in your TV GUIDE for the closed captions symbol (CC).
SLOW
PLAY/ENTER
ANGLE
TITLE/PBC
SEARCH
D.CALL
AUDIO PROGRAM ZOOM
10+
CLR
NOTES:
When selecting closed captions, the captioning will be delayed approximately 10 seconds.
If no caption signal is received, no captions will appear, but the television will remain in the caption mode.
Misspellings or unusual characters may occasionally appear during closed captioning. This is normal with
closed captioning, especially with live programs. This is becauseduring live programs, captions are also
entered live. These transmissions do not allow time for editing.
When captions are being displayed, on-screendisplays, such as volume and mutemay be hidden. If the OSD
display appears, the closed caption willdisappear, When the OSDdisappears, the Closed Caption will appearagain.
Some cable systemsand copy protectionsystems may interferewith the closedcaptioned signal.
If using anindoor antenna orif TV receptionis very poor, the closedcaption decoder maynot appear or
may appear with strange characters or misspelled words. In this case, adjust the antenna for better reception
or use an outdoor antenna.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
DTV setup menu
SETTING CLOSED CAPTION MODE
In DTV mode
1 Press MENU. The main menu screen will appear.
2 Press VOL+/- button to
select FUNCTION
then press CH- button
to enter the submenu.
POWER
TV/DTV
TV/AV
TV/DVD OPEN/CLOSE
FUNCTION
Q.VIEW
INFO
MUTE
LANGUAGE
BLUE SCREEN
NTSC CAPTION
DTV CAPTION
PARENTAL LOCK
ENGLISH
ON
CC1
1
5
2
6
0
3
4
7
-
8
CC
3 Press CH+/- button to
select DTV CAPTION.
9
SAP
P.MODE
CH+
DTV CAPTION
4 Press VOL+ button and
then press CH+/- button
to select CLOSED CAPTION.
CLOSED CAPTION
STYLE
SIZE
TEXT COLOR
TEXT OPACITY
BG COLOR
BG OPACITY
EDGE TYPE
EDGE COLOR
RESET
OFF
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
GREEN
VOL
_
MENU
VOL
+
OK
SLEEP
GUIDE
CH-
CH.LIST FAV.LIST
SIZE
5 Press VOL+ button and
then press VOL+/- button
to set the CLOSED
SETUP PAUSE/STEP SUBTITLE
STOP
REV
PREV
FWD
NEXT
CAPTION:CC1,CC2,
TEXT1,TEXT2,OFF,
SERVICE1,SERVICE2,
D.MENU
A-B
REPEAT
SLOW
PLAY/ENTER
SERVICE3,SERVICE4,SERVICE5,SERVICE6
ANGLE
TITLE/PBC
SEARCH
D.CALL
When setting on, the DTV CC option will be available.
AUDIO PROGRAM ZOOM
6 Press CH+/- button to
select DTV CC and press
VOL+/- button to set
10+
CLR
the desired service.
SETTING DTV CC
This allows youto configure theway you chooseto view the
digital captioning.
Select one ofthe digital servicechannels made availableby
the caption provider.
There are 6standard services. Service1 is designatedas the
Primary Caption Service. This service containsthe verbatim,
or near-verbatim captions for theprimary language being
spoken in theaccompanying program audio.
Service 2 isdesignated as theSecondary Language Service.
This service containscaptions in asecondary language which
are translations ofthe captions inthe primary CaptionService.
The other servicesubchannels are notpre-assigned. It isup
to the discretionof the individualcaption provider toutilize
the remaining servicechannels.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
DTV setup menu
SETTING THE DTV CAPTION STYLE
When "USER SETTING" is set to CUSTOM, you can set
the following items.
POWER
TV/DTV
TV/AV
TV/DVD OPEN/CLOSE
1 Press CH+/- button to
select DTV CAPTION
STYLE.
0101
Q.VIEW
INFO
MUTE
DTV SETUP
1
5
2
6
0
3
4
CAPTION MODE
USER SETTING
DTV CAPTION STYLE
7
-
8
CC
BROADCAST
2 Press VOL+ button to
enter the submenu.
9
SAP
P.MODE
CH+
VOL
_
MENU
VOL
+
3 Press CH+/- button to
select the desired option.
OK
SLEEP
GUIDE
0101
CH-
CH.LIST FAV.LIST
SIZE
DTV SETUP
STYLE2
SETUP PAUSE/STEP SUBTITLE
STOP
REV
4 Press VOL+/- button to
adjust the option.
STYLE
SIZE
LARGE
WHITE
SOLID
NONE
PREV
FWD
NEXT
TEXT COLOR
TEXT OPACITY
EDGE TYPE
D.MENU
A-B
REPEAT
SLOW
PLAY/ENTER
The DTV caption style function lets you change the caption
size and font style.
ANGLE
TITLE/PBC
SEARCH
D.CALL
AUDIO PROGRAM ZOOM
10+
CLR
29
Download from Www.Somanuals.com. All Manuals Search And Download.
DTV setup menu
SETTING THE DTV CAPTION STYLE(continue)
Style
Select this optionto select thefont style ofcaption display
according to yourown preference.
Press the VOL+/- button to selectStyle1, Style2, Style3,
Style4,Style5, Style6, Style7, Style8.
POWER
TV/DTV
TV/AV
TV/DVD OPEN/CLOSE
Q.VIEW
INFO
MUTE
Size
Select this optionto select thesize of captiondisplay according
to your ownpreference.
Press the VOL+/- button to selectSmall, Standard or Large ,
1
5
2
6
0
3
4
7
-
8
CC
9
SAP
P.MODE
Text color
CH+
Select this option to select the text color or the opacity of the text
box of caption display according to your own preference.
Select a color and one of the opacity options.
VOL
_
MENU
VOL
+
OK
SLEEP
GUIDE
CH-
Text Opacity: Specify theopacity for thetext color.
BG (Background) Color: Select abackground color.
CH.LIST FAV.LIST
SIZE
SETUP PAUSE/STEP SUBTITLE
STOP
REV
PREV
BG (Background) Opacity: Select theopacity for the
background color.
EDGE TYPE: Specify theopacity for thetext color.
FWD
NEXT
D.MENU
A-B
REPEAT
SLOW
PLAY/ENTER
EDGE COLOR: Select abackground color.
ANGLE
TITLE/PBC
SEARCH
D.CALL
AUDIO PROGRAM ZOOM
10+
CLR
30
Download from Www.Somanuals.com. All Manuals Search And Download.
DTV setup menu
SETTING THE DAYLIGHT SAVING
Daylight saving timeis automatically setby specially
broadcasted signals.
This menu itemallows you todisable the automatic
setting of daylightsaving time. Thisis useful ifyou live
in an areaor state wheredaylight saving isnot applied,
but you receivechannels from otherareas where daylight
saving signals arebroadcasted.
POWER
TV/DTV
TV/AV
TV/DVD OPEN/CLOSE
Q.VIEW
INFO
MUTE
1 Press MENU. The main menu screen will appear.
1
5
2
6
0
3
4
7
-
8
CC
2 Press VOL+/- button to
select TIME option,
TIME
9
SAP
P.MODE
then press CH- button
to enter.
TIME
--:-- AM
--:-- AM
--:--AM
ON
CH+
TIMER ON
TIMER OFF
DAYLIGHT SAVING
TIME ZONE
VOL
_
MENU
VOL
+
CENTRAL
3 Press CH+/- button to
OK
SLEEP
GUIDE
select DAYLIGHT SAVING,
then press VOL+/- button
to select ON for automatic
clock correction for daylight
saving time, based on
CH-
CH.LIST FAV.LIST
SIZE
SETUP PAUSE/STEP SUBTITLE
STOP
REV
PREV
FWD
NEXT
specially broadcasted signals.
Select OFF to disable automatic
clock correction based on the
specially broadcasted signals.
D.MENU
A-B
REPEAT
SLOW
PLAY/ENTER
ANGLE
TITLE/PBC
SEARCH
D.CALL
SETTING THE TIME ZONE
AUDIO PROGRAM ZOOM
This function allowsyou to selectyour local timezone.
Broadcasted time informationwill correct theclock display
for your localtime.
10+
CLR
1 Press MENU. The main menu screen will appear.
2 Press VOL+/- button to
select TIME option,
TIME
then press CH- button
to enter.
TIME
--:-- AM
--:-- AM
--:-- AM
ON
TIMER ON
TIMER OFF
DAYLIGHT SAVING
TIME ZONE
3 Press CH+/- button to
select TIME ZONE option.
CENTRAL
4 Press VOL+/- button to
select your viewing area
time zone: NEWFOUNDLAND,
ATLANTIC, EASTERN, CENTRAL,
MOUNTAIN, PACIFIC, ALASKA,
HAWAII, or SAMOA
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Functions
GUIDE
- This activates some, butnot all, electronicprogram guides
(EPG data) whenit is usedand transmitted bysome DTV station
providers. It isonly supported whenreceiving DTV channels.
GUIDE
1/3 >>
POWER
TV/DTV
TV/AV
TV/DVD OPEN/CLOSE
03:00 ---04:00
Q.VIEW
INFO
MUTE
Moving picture 480i 4:3
1
5
2
6
0
3
4
04:00 ---05:00
Moving picture 480i 4:3
7
-
8
CC
9
SAP
P.MODE
CH+
1. Press theGUIDE button to switchon GUIDE.
2. Press theCH+/- or VOL+/-button to selectdesired program,
then press theOK button to displaythe selected program.
3. Press theGUIDE or EXIT button again toswitch off GUIDE and
return to TV viewing.
VOL
_
MENU
VOL
+
OK
SLEEP
GUIDE
CH-
CH.LIST FAV.LIST
SIZE
SETUP PAUSE/STEP SUBTITLE
STOP
REV
PREV
FWD
NEXT
D.MENU
A-B
REPEAT
SLOW
PLAY/ENTER
FAVORITE CHANNELS LIST
TITLE/PBC
SEARCH
D.CALL
ANGLE
You can create your own Favorite List. Use the “FAV.LIST”
button on the remote control when a channel is highlighted
and then you can add or delete the channel to/from the
Favorite List.
AUDIO PROGRAM ZOOM
10+
CLR
FAVORITE CHANNELS
1
2
3
4
5
6
7
8
-
-
-
-
-
-
-
-
-------
-------
-------
-------
-------
-------
-------
-------
Press the FAV.LIST button open the favorite channel
list, press CH+/-button to select the channel andpress
VOL+/- button to select to add or delete. Press the OK button
to confirm.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Functions
QUICKLY VIEW
This function enablesquick swap tothe last watchedprogram.
1 Suppose the channelnumber you used
just now is8 and thechannel number
you are usingis 18 (asshown in thefigure).
POWER
TV/DTV
TV/AV
TV/DVD OPEN/CLOSE
Q.VIEW
INFO
MUTE
2 If you wantto return tothe last watched
program channel 8, you can simplypress
the Q.VIEW button.
1
5
2
6
0
3
4
7
-
8
CC
3 If you wantto return tochannel 18, press
the button again. Use this functionto easily
change between thechannel you are
using and thechannel you lastused.
9
SAP
P.MODE
CH+
VOL
_
MENU
VOL
+
OK
SLEEP
GUIDE
CH-
CH.LIST FAV.LIST
SIZE
SLEEP TIMER
SETUP PAUSE/STEP SUBTITLE
STOP
REV
To set the TV to turn off after a preset amount of time, press SLEEP
button repeatedly to select
PREV
FWD
NEXT
D.MENU
A-B
REPEAT
the number of minutes. First the
OFF option appears on the screen,
followed by the following sleep
SLOW
PLAY/ENTER
ANGLE
TITLE/PBC
SEARCH
D.CALL
timer options:
(5 MINUTE,10 MINUTE, 15 MINUTE,
30 MINUTE,45 MINUTE, 60 MINUTE,
AUDIO PROGRAM ZOOM
SLEEP OFF
10+
CLR
90 MINUTE,120 MINUTE,
180 MINUTE, 240MINUTE,OFF)
To confirm the sleeptimer setting,
press SLEEP and the remaining
time will be displayed for a few
seconds. To cancel thesleep timer,
Press SLEEP repeatedly until the
display turns toOFF.
PICTURE MODE
Press the P.MODE button to switch
desired picture quality mode.
Four kinds of picture modes
(i.e., "MILD","STANDARD","VIVID" ,
"CUSTOM", ) can be selected in turn.
MILD
33
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD Features
Basic Playback
Preparations
Stop playback
1. Press STOP
button to go to stop mode, the TV
Press the DVD/TV button on the remote control or
the TV to enter the DVD status.
screen will show the start logo. For some discs the
player can recall the location where stopped, such
as DVDs and audio CDs.
Basic playback
2. Press PLAY/ENTER to playback to resume play-
back from the location where playback is stopped
or from the beginning of the disc.
1. Press OPEN/CLOSE to open the disc tray,
place a disc in the disc tray.
3. Press STOP twice to stop completely.
There are two different disc sizes. Place the
disc in the correct GUIDE on the disc tray. If the
disc is out of the GUIDE, it may damage the disc
and cause the DVD player to malfunction.
Do not place a disc that is unplayable in this
DVD player.
Previous and Next
During Playing, pressing the PREV
key will
restart the current chapter and skip chapters
backwards with each subsequent press until the
start of thedisc is reached.
Each press of NEXT key duringplaying will
skip the current chapter and play the next one.
2. Press OPEN/CLOSE to close the disc tray, the
playback will automatically start.
Some discs do not start automatically. Press
PLAY/ENTER tostart playback.
3. Some discs may start playback with a menu. Use
the cursor buttons on the remote control to select
menu options and press PLAY/ENTER to start. You
may also press the digit buttons to select a menu
option directly. Many DVDs will not allow this during
start-up.
Fast forward and Fast reverse
1. Press FWD
to fast forward through the disc.
button is pressed, the
Each time the FWD
fast forward motion speed changes.
2. Press PLAY/ENTER to resume normal playback.
Pause playback
3. Press REV
to fast reverse through the disc.
button is pressed, the
Each time the REV
1. Press PAUSE/STEP to pause playback (still mode).
The sound will be muted during still mode.
fast reverse motion speed changes.
4. Press PLAY/ENTER to resume normal playback.
2. Press PLAY/ENTER to resume normal playback.
Single step playback
1. When paused, press PAUSE/STEP continuous
to single step forward tothe next frame in the
video.
2. Press PLAY/ENTERto resume normal playback.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD Features(Continued)
Advanced Playback
IMPORTANT NOTE:
All described functionsare for DVDdiscs. If youplay other formatdiscs, the operation
and on screendisplay will bedifferent.
PROGRAM
SUBTITLE
Press "SUBTITLE ", the screen will display "SUBTI-
TLE 01/XX XXXXX", "01" indicates the original
number of this language; "XX" indicates total number
of language; "XXXXXX" indicates the language of
country. (the number of language depends on disc).
This function can select up to 32 languages display-
ed on screen.
When playing discs, press "PROGRAM" to enter
program mode. Press the digit buttons to select the
program number that you want. When finished move
the cursor to select "START" . This will start the
program playback.
SEARCH
REPEAT
Press "SEARCH" once to display the search
menu. Press the button again to select. Press
the program number buttons to input the item
you require. Press PLAY/ENTER to confirm.
Press " REPEAT " and Chapter repeat will be
displayed on screen, the second press will display
Title repeat, the third press will display All repeat,
the fourth press will cancel this function.
SLOW
A-B
Press SLOW to play a disc in slow forward. Each
time the SLOW button is pressed, the slow
motion speed changes.
Press " A-B " to begin start-point, press again
to set an end point and complete setting. The
selected section A-B will be repeated. The third
press will cancel this function.
Press PLAY/ENTER to resume normal playback;
Note: This function does not work for CD and MP3.
ANGLE
TITLE/PBC
When enjoying sports, concert or theatre, press this
key to watch same actions in different angles. (Valid
for discs possessing this function. Using a disc
recorded in multi-angle you can view the scene from
different angles,for example,front, side, whole view
and exterior scene).
With some DVD discs pressing this key will display
the title menu. You can then use the digit buttons
to select the item you prefer.
AUDIO
D.MENU
Press this key to change the mode of audio.
such as: Audio 1/2: AC 3 2 CH English
Audio 2/2: AC 3 5.1 CH English
Press this key to display root menu,select item
according to your preference. (This function will work
with a DVD having a multi-layer menu.)
Press this button to cycle between Mono Left, Mono
Right, Mix-Mono and Stereo.
Note: When press this button continuously, you must
above 3 seconds interval.
D.CALL
Pressing this key will cycle through "Title Elapsed",
"Title Remain", "Chapter Elapsed", "Chapter Remain"
and "Display off ".
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Special Playback Functions
JPEG DISC PLAYBACK
When a disc containing standard JPEG picture files is inserted into the player, a
navigation menu will be displayed automatically. Use the UP and DOWN cursor
buttons to select a file then press PLAY/ENTER. The slide show will commence.
Press PREVIOUS or NEXT to move between pictures. Press pause to stop on the
current picture. Press PLAY/ENTER to resume normal playing.
A JPEG disc contains JPEG (.jpg) format picture information that can be decoded
by a micro-computer software and displayed through the video output interface or on
the television screen.
This function has many applications. For example one can save files from a scanner
or digital camera in the JPEG format, record these on a CD-R disc and present them
to an audience through this player.
The JPEG format is a convenient method to store images in a small amount of
memory space, and is ideal for archiving information.
MP3 PLAYBACK
When playing anMP3 disc, anavigation menu willbe displayed automatically. In themenu, use UP
or DOWN cursorbuttons to choosethe folder, then press PLAY/ENTER to enterthe folder. Use the
UP and DOWNcursor buttons toselect the fileand press PLAY/ENTER. Pressing theLEFT cursor
button will takeyou to theprevious screen/menu.
SCREEN SAVER FUNCTION
This unit employs a screen savermode to helpprotect the tubeduring static videopictures. This can
be turned offon the GENERALSETUP PAGE.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD System Setup
DVD System Setup
General Setup Process
1.Press the SETUP button, the
General Setup Page,Preference
Page will be displayed in turn.
SETUP
..General Setup Page..
.
3:Ps
.
3:Lb
TV Display
Angle Mark
OSD Lang
Caption
LB
On
4
4
2.Press to select, the
or
item, then press to enter the
submenu.
ENG
On
16
9
Screen Saver Off
PLAY/ENTER
or
3.Press to select then
press PLAY/ENTER to confirm.
4.Press EXIT key or press SETUP
repeatedly to exit the set-up
menus.
..Preference Page..
Parental
Password
Default
1 Kid Saf
2 G
3 Pg
4 Pg 13
5 Pgr
6 R
7 Nc17
8 Adult
General Setup Page
ASPECT RATIO DESCRIPTION
When using the DVD with the internal TV,
select 4 3/LB.
..General Setup Page..
The following information applies only
when the DVD output is connected to an
external TV.
.
3:Ps
.
3:Lb
TV Display
Angle Mark
OSD Lang
Caption
LB
On
4
4
ENG
On
16
9
SETUP
Screen Saver Off
4:3/PS (PS = Pan and Scan)
You may select if you have a normal aspect
ratio (4:3) TV, although the NORMAL/LB
(letter box) is a more common choice. In PS
mode, widescreen material will fill the screen, but at the expense of chopping
off extreme left and right edges of the original film picture. For this feature to
work, the disc must be specially coded. Such discs are uncommon.
4:3/LB (LB = Letter Box)
PLAY/ENTER
You may select this if you have a normal aspect ratio (4:3) TV. Widescreen
material will be shown in pure unaltered form, allowing the entire picture area
of the original film to be viewed without any side cropping. Black bars will
appear above and below the picture.
16:9
You may select this if you have a widescreen (16:9) TV. Back bars may still
appear above and below the picture even if using a widescreen TV. This is
because some film directors prefer to use ultra widescreen aspect ratios e.g.
2.35:1. This will normally be indicated on the DVD packaging.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD System Setup(Continued)
DVD System Setup
General Setup Page
..General Setup Page..
ANGLE MARK: Users can select a particular
.
camera angle when playing a DVD which offers
TV Display
Angle Mark
OSD Lang
Captions
LB
On
On
Off
ENG
On
multiple angles.
This item allows you to set Angle Mark ON or OFF.
Screen Saver Off
On Screen Display (OSD) Language: Users
can select on-screen display language.
..General Setup Page..
TV Display
Angle Mark
OSD Lang
Caption
LB
On
ENG
On
English
Spanish
Screen Saver Off
..General Setup Page..
CAPTIONS: This function allows you to display or
hide the caption.
TV Display
Angle Mark
LB
On
OSD Lang
Captions
ENG
On
Screen Saver Off
On
Off
SCREEN SAVER: If the screen saver is on, then
there will be an animated picture of DVD on the
screen whenever the DVD player is idle for more
than 3 minutes .
..General Setup Page..
TV Display
Angle Mark
LB
On
OSD Lang
Caption
ENG
On
Screen Saver Off
On
Off
38
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD System Setup(Continued)
DVD System Setup
Preference Page
The Preference Page is only available when there is no disc
in the player. These settings are applied consistently to all
discswhichareinsertedandplayed.
SETUP
PARENTAL: The parental
control function works in
..Preference Page..
1 Kid Saf
2 G
3 Pg
4 Pg 13
5 Pgr
6 R
7 Nc17
8 Adult
Parental
conjunction with the
different censorship classes
assigned to DVDs. These
classes help to control the
types of DVDs that the family
watches. There are up to 8
censorship classes for DVDs.
Password
Default
PLAY/ENTER
Note:
1 To change this setting you must enter your password.
(Initial password is 0000)
2 When set to OFF, all discs may be viewed.
PASSWORD CHANGE:
You can change your password by
SETUP
..Preference Page..
Parental
entering 4 digits. You must confirm
the 4 digits before the new password
can be accepted.
Password
Default
Change
PLAY/ENTER
Old Password
New Password
Confirm PWD
NOTE:If you forgetyour password
or a password is accidentally set
enter 2881 as the password. This
will enable you to regain control.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD System Setup(Continued)
DVD System Setup
DEFAULT: Resets all settings
SETUP
..Preference Page..
(except password and parental
lock status) for this DVD player
back to the manufacturers
original settings. Press ENTER
to perform the reset.
Parental
Password
Default
Reset
PLAY/ENTER
Note:
Some functions may not be available depending on the type of disc.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Playable Discs
The following discs can be played:
You cannot play discs other than those listed above.
You cannot play non-standardized discs, even if they may be labelled as above.
The performance of CD-R or CD-RW disc depends on the way the disc was burned. In a few cases,
their performance may not be consistant or may not even operate at all.
This DVD Playeris designed andmanufactured according tothe Region Management
Information that isrecorded on aDVD disc. Ifthe Region numberdescribed on theDVD disc
does not correspondto the Regionnumber of thisDVD Player, this DVD playerwill not play
that disc.
This Region numberof this DVDPlayer is .
1
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Disc Protection and DVD Characteristics
Compare DVD disc with other discs:
DVD
LD
SVCD
VCD
CD
Digital/
MPEG I
Encode
method
Digital/MPEG
Digital
Digital
Analog
Single- Double Single- Double-
side
-side
side
side
single- single double- double-
650MB
650MB
650MB
Capacity
layer
4.7G
-layer layer
8.5G
layer
17G
9.4G
Single-side
60 minutes
double-side
120 minutes
133
242
266
484
minutes minutes minutes minutes
45 minutes 74 minutes 74 minutes
Playing Time
Disc diameter
12cm/8cm
30cm/20cm
12cm
12cm
12cm/8cm
No more than
430 line
Horizontal
resolution
No more than No more than
350 line
More than 500 line
250 line
Picture
proportion
One kind
One kind
Multiple kinds
32 kinds
One kind
16 kinds
at most
Subtitle
4 kinds
4 kinds
at most
4 kinds
at most
Language
2 kinds
2 kinds
8 kinds
48KHz, 96KHz/
6, 20, 24bit
44.1KHz/
16bit
44.1KHz/
16bit
44.1KHz/
16bit
44.1KHz/
16bit
Sound quality
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting guide
To assist in location possible faults use help guide below.
BREAKDOWN PHENOMENON
CHECKING
SOUND
PICTURE
The aerial direction and connection
Picture with snow
Noise
This is called "ghosting" and can be minimized with
an outside aerial, and good quality cable and
terminations. Altering the aerial direction can also
minimize this effect.
Double or Triple Image
Normal
Electrical interference which can be caused by cars,
motorbikes etc, Fluorescent lamps and dirty
insulators on overhead power cables.
Noise
Disturb
Volume Sound mute
Normal
No Picture
No color
No sound
Ensure that the power supply is connected to
the TV setand turned on. Also ensure that the
TV set is not in "Listen Mode" or that the
brightness and contrast are not turned down.
No sound
Adjust color control
Adjust channel again
Normal volume
Normal or Weak Volume
Scramble
Color Purity isa fault thatcan be causedby moving the
TV set, placingmagnets near theTV screen orturning
on/off house holdappliances such asvacuum cleaners
near the TVset. Turnthe TV off with themain power
switch for 15minutes. When thepower is turnedon
again the TVset will automaticallydegauss the picture.
In severe casesleave the TVset turned offover night.
Color Spot
Normal volume
Note:
1.If the fault can not be corrected using the above guide consult with your local authorized service
center.
2.The TV set must only be repaired by a qualified registered service person. Never attempt to
remove the back cover as TV set has dangerous voltages inside that may cause a fatality or fire.
3. The cabinet may produce the occasional "snapping sound" This is normal and caused by the
materials in the cabinet expanding with room temperature changes.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
The specifications offered you here are for reference only. With product improvement
there may be some differences between the description and the final product.
TCR20-A
TCF20-A
TCR13 -A
ATSC
13
20
80
85
90
TCR13-A
TCR20-A
368 mm x 378mm x 371mm
503 mm x 472 mm x 500mm
503 mm x 472 mm x 500mm
TCF20-A
NOTE
Design and specifications are subject to change without notice.
Dimensions quoted in this manual are approximate.
The registered logos shown in this manual, such as those on the page showing playable discs
contents, are those of the license holders and the associated trademarks holders. They are
shown for informational purposes only and do not indicate content or capability in all software,
nor with all hardware.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty
Responsibility of Haierto the purchaserwith
respect to theproduct, and shall
This Haier brandproduct, when shippedin
its original packaging, will be freefrom
defective workmanship andmaterials, and
agrees that itwill, at itsoption, either repair
the defect orreplace the defectiveproduct
with a newor re-manufactured equivalentat
no charge tothe purchaser, for parts or
labor for theperiods set forthbelow:
constitute full satisfactionof all claims,
whether based oncontract, negligence, strict
duality or otherwise. In no eventshall Haier
be liable, orin any wayresponsible for any
damages or defectsin the productwhich
were caused byrepairs or attemptedrepairs
performed by anyoneother than an
authorized service centeror dealer; norshall
Haier be liable, or in anyway responsible
for incidental orconsequential economic or
property damage. Somestates do notallow
the exclusion ofincidental or consequential
damages, so thatabove exclusion maynot
apply to you.
This warranty doesnot apply tothe
appearance of theproduct or theexterior of
the product, whichhas been damagedor
defaced, altered ormodified in designor
construction. It doesnot apply tothe
additional excluded itemsset forth below:
The warranty commenceson the datethe
item was purchasedand the original
purchase receipt mustbe presented tothe
authorized service centerbefore warranty
repairs are rendered.
THIS WARRANTYGIVES YOU
SPECIFIC LEGAL RIGHTS. YOU MAY
ALSO HAVE OTHER RIGHTSWHICH
VARY FROM STATE TO STATE.
Warranty period for this product: 90 day labor
and one yearparts.
The limited warrantydescribed herein isin
addition to whateverimplied warranties may
be granted topurchasers by law. ALL
IMPLIED WARRANTIES INCLUDING THE
WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR USEARE LIMITEDTO THE
PERIOD(s) FROM THE DATE OF PURCHASE
SET FORTH BELOW. Somestates do not
allow limitations onhow long animplied
warranty lasts, sothe above limitationmay
not apply toyou.
Additional items excludedfrom warranty
coverage: non-rechargeable batteries.
Where to obtainservice: For thelocation of
the nearest Haierauthorized service centeror
to obtain productliterature, accessories,
supplies or customerassistance,
please call 1-877-337-3639.
What to doto obtain service:ship or carryin
your product toan authorized servicedealer
or center .Besure to haveproof of purchase.
If you shipthe product, besure it is
packaged carefully.
Haier America
New York, NY 10018
Neither the salespersonnel of theseller nor
any other personis authorized tomake any
warranties other thanthose described herein,
or to extendthe duration ofany warranties
beyond the timeperiod described hereinon
behalf of Haier.
The warranties describedherein shall bethe
sole and exclusivewarranties granted by
Haier and shallbe the soleand exclusive
remedy available tothe purchaser. Correction
of defects inthe manner andfor the period
of time describedherein, shall constitute
complete fulfillment ofall abilities and
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
TCR13-A
TCR20-A
TCF20-A
Download from Www.Somanuals.com. All Manuals Search And Download.
COMISIÓN FEDERAL DE COMUNICACIONES,
ADVERTENCIA: Este equipo puede generar o
usar energía de radio frecuencia. Los cambios o
las modificaciones a este equipo pueden provocar
interferencia perjudicial a menos que las
PRECAUCIÓN: CUALQUIER
OPERACIÓN REALIZADAAQUÍ
CONLLEVARIESGO
DE EXPOSICIÓNA UNARADIACIÓN
PELIGROSA.
PRECAUCIÓN: RADIACIÓN LÁSER
VISIBLE E INVISIBLECUANDO SEABRE Y
SE ANULAEL INTERRUPTORDE
BLOQUEO. NO MIREDIRECTAMENTE EL
HAZ.
modificaciones hayan sido aprobadas
expresamente en el manual de instrucciones. El
usuario puede perder la autoridad para usar este
equipo si se realizan cambios o modificaciones no
autorizadas.
SEGURIDAD EN RELACIÓN CON EL LÁSER
Esta unidad utiliza un láser. Sólo una persona de
reparaciones calificada puede quitar la cubierta o
intentar reparar este dispositivo, debido a las
posibles lesiones a la vista que puede provocar.
UBICACIÓN: EN ELINTERIOR, CERCA
DEL MECANISMO DE LA BANDEJA.
32
34
36
37
41
42
43
44
45
Download from Www.Somanuals.com. All Manuals Search And Download.
El símbolo derayo con puntade flecha dentrode
un triángulo equiláterose utiliza paraadvertir al
usuario acerca dela presencia dealto voltaje no
aislado dentro dela caja del equipo, de magnitud
suficiente como paraconstituir un riesgode
descarga eléctrica paralas personas.
ADVERTENCIA
RIESGO DE DESCARGA
ELÉCTRICA . NOABRIR
!
El signo deadmiración dentro deun triángulo
equilátero tiene comoobjetivo advertir alusuario
acerca de laexistencia de instrucciones
importantes de funcionamientoy mantenimiento
(reparación) en ladocumentación que acompaña
a este electrodoméstico.
ADVERTENCIA: NO ABRALA CUBIERTA SUPERIOR.
NO HAYPIEZAS REEMPLAZABLES
POR EL USUARIOEN EL INTERIOR.
DEJE TODAS LASREPARACIONES
EN MANOS DE PERSONALDE
MANTENIMIENTO CUALIFICADO.
!
ADVERTENCIA: PARAPREVENIR INCENDIOS ODESCARGAS, NO EXPONGA
ESTE ELECTRODOMÉSTICOA LALLUVIA OHUMEDAD.
PRECAUCIÓN: PARAPREVENIR UNADESCARGA ELÉCTRICANO UTILICE ESTE
ENCHUFE POLARIZADO CONUN CABLE PROLONGADOR,
RECEPTÁCULO U OTRATOMA DE CORRIENTEA NOSER QUE LAS
PUNTAS SE PUEDAN INTRODUCIRPOR COMPLETO PARA
PREVENIR QUE QUEDANDESCUBIERTAS.
PRECAUCIÓN: Estas instrucciones de mantenimiento están indicadas
solamente para personal de mantenimiento cualificado. Para reducir el
riesgo de descargas eléctricas, no realice ninguna operación de
mantenimiento que no esté indicada en estas instrucciones de
funcionamiento a no ser que esté cualificado para hacerlo.
PRECAUCIÓN: CUALQUIER OPERACIÓN REALIZADAAQUÍ CONLLEVA
RIESGO DE EXPOSICIÓN A UNARADIACIÓN PELIGROSA.
INSTRUCCIONES DE SEGURIDAD IMPORTANTES
1) Lea estas instrucciones.
2) Conserve estas instrucciones.
3) Tenga en cuenta todas las advertencias.
4) Siga todas las instrucciones.
5) No utilice esta unidad cerca del agua.
6) Límpiela sólo con un paño seco.
7) No obstruya las aberturas para ventilación. Instale la unidad según las
instrucciones del fabricante.
8) No instale este producto cerca de ninguna fuente de calor, como por ejemplo,
radiadores, reguladores de calor, estufas u otros dispositivos (incluidos
amplificadores) que produzcan calor.
9) No haga caso omiso a la medida de seguridad del enchufe polarizado o con
descarga a tierra. El enchufe polarizado tiene dos patas y una de ellas es
más ancha que la otra. El enchufe con descarga a tierra tiene dos puntas y
una tercera clavija para la descarga a tierra. La punta más ancha y la tercera
clavija están puestas para su seguridad. Si el enchufe suministrado no
coincide con su tomacorriente, consulte con un electricista para reemplazar
el tomacorriente obsoleto.
10) Evite pisar o apretar el cable de alimentación, especialmente en los enchufes,
tomacorrientes y en el punto por donde salen del artefacto.
11) Utilice sólo los complementos y accesorios especificados por el fabricante.
Download from Www.Somanuals.com. All Manuals Search And Download.
12) Utilice la unidad sólo con el carro, soporte, trípode, repisa o mesa recomendados
por el fabricante o que se venda junto con el producto.
Cuando se usa un carro, tenga cuidado al mover el
carro junto conel aparato paraevitar caídas.
13) Desenchufe esteartefacto durante lastormentas
eléctricas o cuandono se loutilice durante
períodos prolongados.
14) Derive todaslas reparaciones apersonal de reparacionescalificado. Es
necesario reparar el artefacto cuando está dañado de alguna manera, por
ejemplo, cuando elcable de suministrode energía oel enchufe estándañados,
cuando se derrama líquido sobre la unidad o caen objetos dentro de la misma,
cuando el producto ha estado expuesto a la lluvia o a la humedad, cuando no
funciona con normalidad o cuando se ha caído.
15) No debe exponerse el artefacto a goteos o salpicaduras, y no se deben
colocar objetos llenos de líquido, tales como floreros, sobre el mismo.
16) El enchufe principalo la entradadel electrodoméstico seutiliza como
dispositivo de desconexión, manténgalo en un lugar manejable durante el
funcionamiento normal del aparato.
17) LÍNEAS DE ENERGÍA
Los sistemas de antena exteriores no deben colocarse cerca de líneas de energía
aéreas u otros circuitos de luz eléctrica o energía, o en lugares donde pueda caer
sobre dichas líneas de energía o circuitos. Al instalar un sistema de antena exterior,
debe tener especial cuidado de no tocar los circuitos o líneas de energía, ya que el
contacto podría ser fatal.
18) SOBRECARGA
No sobrecargue los tomacorrientes de la pared o los cables de prolongación, ya que
esto puede provocar riesgo de incendio o descarga eléctrica.
19) ENTRADA DE OBJETOS Y LÍQUIDOS
No ponga objetos dentro del producto a través de las aberturas, ya que pueden tocar
puntos con voltaje peligroso o poner en cortocircuito partes que podrían ocasionar
incendio o descarga eléctrica. No derrame ni vaporice nunca ningún tipo de líquido en
la unidad.
20) DESCARGA ATIERRA DE LAANTENA EXTERIOR
Si se conecta una antena exterior o sistema de cable a la unidad, asegúrese de que
estén conectados a tierra de manera tal de proveer algún tipo de protección contra las
sobretensiones y las cargas estáticas intensificadas. La Sección 810 del Código
Eléctrico Nacional de los Estados Unidos (NEC), ANSI/NFPA 70 brinda información
acerca de la conexión a tierra adecuada del mástil y de la estructura de soporte, la
conexión a tierra del cable conductor a la unidad de descarga de la antena, la
conexión de los electrodos de tierra y los requisitos para estos electrodos.
EJEMPLO DE DESCARGA A
ANTENA
TIERRA DE LA ANTENA
Cable de acometida
ABRAZADERA DE LA
CONEXIÓN A TIERRA
ANTENA
UNIDAD DE DESCARGA
EQUIPO DE SERVICIO
ELÉCTRICO
CONDUCTORES A TIERRA
ABRAZADERAS DE LA CONEXIÓN A TIERRA
SISTEMA DE ELECTRODOS PARA LA DESCARGA A
TIERRA DEL SERVICIO DE ENERGÍA
Download from Www.Somanuals.com. All Manuals Search And Download.
21) REPARACIONES
No intente reparar esta unidad usted mismo, ya que puede exponerse a voltaje peligroso u otros
peligros si abre el aparato o quita cubiertas. Derive todas las reparaciones a personal de
reparaciones calificado.
22) DAÑOS QUE REQUIEREN REPARACIÓN
Desenchufe esta unidad del tomacorriente de la pared y derive la reparación a personal de
reparaciones calificado en las siguientes circunstancias:
a. Cuando el cable de suministro de energía o el enchufe estén dañados.
b. Si se ha derramado líquido o si han caído objetos dentro de la unidad.
c. Si la unidad ha estado expuesta a la lluvia o al agua.
d. Si la unidad no funciona con normalidad aunque se sigan las instrucciones de
funcionamiento. Ajuste sólo los controles a los que se refieren las instrucciones de
funcionamiento, ya que el ajuste incorrecto de otros controles puede resultar en daños y
por lo general requerirá mucho trabajo de un técnico calificado reparar la unidad para que
vuelva a funcionar con normalidad.
e. Si la unidad se ha caído o si el gabinete resultó dañado.
f. Cuando la unidad presenta un cambio notable en el rendimiento, esto indica
necesidad de reparación.
23) REPUESTOS
Cuando se necesitan repuestos, asegúrese de que el técnico de reparaciones use los repuestos
especificados por el fabricante o los que tengan las mismas características que la pieza original.
Las sustituciones no autorizadas pueden ocasionar fuego, descarga eléctrica u otros riesgos.
24) REVISIÓN DE SEGURIDAD
Cuando se finalicen las reparaciones correspondientes a esta unidad, pídale al técnico de
reparaciones que realice revisiones de seguridad para determinar si la unidad está en
condiciones de funcionamiento adecuadas.
25) CALOR
El producto debe ubicarse lejos de fuentes de calor tales como radiadores, rejillas de entrada de
calor, estufas u otros productos (incluso amplificadores) que produzcan calor.
26) RANURA PARA EL DISCO
Mantenga sus dedos lejos de la ranura para los discos cuando ésta se cierra. Puede
provocar lesiones personales serias.
27) CONEXIÓN
Cuando conecte el producto a otro equipo, apáguelo y desenchufe todo el equipo del
tomacorriente de la pared. Si no lo hace, se pueden ocasionar descargas eléctricas y lesiones
personales graves. Lea el manual del usuario del otro equipo con atención y siga las
instrucciones cuando realice las conexiones.
28) VOLUMEN DE SONIDO
Baje el volumen al nivel mínimo antes de encender el producto. De lo contrario, el volumen de
sonido alto y repentino le puede provocar lesiones auditivas o daños a los parlantes.
29) DISTORSIÓN DEL SONIDO
No permita que el producto emita sonido distorsionado durante un tiempo prolongado.
Puede provocar el sobrecalentamiento del parlante e incendio.
30) RAYO LÁSER
No mire hacia adentro de la abertura de la ranura para el disco o la abertura para ventilación del
producto para ver la fuente del rayo láser. Puede ocasionarle daños en la vista.
31) DISCO
No utilice un disco rajado, deformado o reparado. Estos discos se rompen fácilmente y pueden
provocar lesiones personales serias y mal funcionamiento del producto.
32) NOTAPARAEL INSTALADOR DELSISTEMA DE CABLE
Este llamado de atención se proporciona para que el instalador del sistema de televisión por
cable recuerde el Artículo 820-40 del Código Eléctrico Nacional de los Estados Unidos, que
proporciona pautas para la descarga a tierra adecuada y, en particular, especifica que el cable a
tierra debe estar conectado con el sistema de descarga a tierra del edificio, tan cerca del punto
de entrada del cable como sea posible.
Download from Www.Somanuals.com. All Manuals Search And Download.
Si la imagen no es clara o aparece con lluvia, se recomienda el uso de una
antena externa aérea, que por lo general se instala afuera.
Nota:
* Se recomienda el uso de una antena coaxial de 75 ohm para evitar interferencias.
* Para evitar la interferencia de las señales eléctricas, no una el cable de la antena al cable
conductor de corriente.
Instalación de las pilas
Quite la tapa de las pilas.
Introduzca dos pilas AAA haciendo coincidir las
polaridades +/- de las pilas con las marcas +/- que
se encuentran dentro del compartimiento de las
pilas.
Consejos para el funcionamiento
del control remoto
Cuando no se utilice el control remoto durante un período prolongado, o cuando las pilas se
gastaron, quite las pilas para prevenir pérdidas.
No arroje las pilas al fuego. Disponga de las pilas usadas de la manera especificada.
No deje caer el control remoto, ni lo humedezca o desarme.
Download from Www.Somanuals.com. All Manuals Search And Download.
TCR13-A
TCR20-A/TCF20-A
Download from Www.Somanuals.com. All Manuals Search And Download.
(Para ajustar el equilibrio de salida
del sonido.)
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Conexión con la antena
Si está usando una antena interior o exterior, siga las instrucciones a continuación que le
correspondan a su sistema de antena. Si está utilizando un servicio de televisión por cable
(CABLE), consulte las conexiones de televisión por cable.
Combinación de antena VHF/UHF (cable único de 75 ohm o 300 ohm con
cable conductor doble)
Conecte el cable de 75 ohm de la antena con
combinación VHF/UHF al enchufe de entrada
RF.
Enchufe de
entrada RF
Enchufe de
entrada RF
Si utiliza un cable conductor doble de 300
ohm plano UHF, conecte estos cables planos
a un transformador/adaptador que coincida de
75/300 ohm opcional (disponible en muchos
comercios) y luego conecte el adaptador al
conector de entrada RF en la parte de atrás
del televisor.
cable coaxial
de 75 ohm
Transformador para
300-75 ohm
Combinación de antena VHF/UHF (cables conductores de 300 ohm VHF y
UHF individuales)
Conecte el cable conductor doble UHF de 300
ohm con el combinador (no se suministra)
Conecte el cable conductor doble VHF de 300
ohm con el transformador de 300-75 ohm.
Una el transformador con el combinador,
Enchufe de
entrada RF
Transformador
para 300-75 ohm
luego conecte el combinador al tomacorriente
de entrada RF.
Combinador
UHF de 300
VHF 300 ohm
Antenas VHF/UHF individuales (cable VHF de 75 ohm y cables conductores
dobles de 300 ohm UHF)
Enchufe de
entrada RF
Conecte el cable VHF de 75 ohm y el cable
conductor doble de 300 ohm UHF con el
combinador. Una el combinador con el
enchufe de entrada RF.
VHF 75 ohm
Combinador
UHF de 300
Download from Www.Somanuals.com. All Manuals Search And Download.
Conexiones para televisión por cable
Esta unidad tiene un rango de sintonización extendido y puede sintonizar la mayoría de los canales de cable sin
utilizar la caja de conversión de televisión por cable. Algunas empresas de cable ofrecen “canales pagos
premium", en los cuales se encripta la señal. Para desencriptar estas señales para que la visualización sea
normal es necesario el uso de un dispositivo desencriptador que por lo general lo suministra la empresa de
PARA LOS SUSCRIPTORES AL SERVICIO BÁSICO DE TELEVISIÓN POR CABLE
Para el servicio básico de cable que no requiere una caja para
conversión o desencriptador, conecte el cable coaxial de 75 ohm
directamente en la entrada RF en la parte de atrás de la unidad.
Entrada RF
jack
Cable coaxial
de 75 ohm
PARALOS SUSCRIPTORES AL SERVICIO DE TELEVISIÓN POR CABLE
ENCRIPTADA
Si se suscribe a un servicio de televisión por cable que requiere el uso de una caja para conversión o
desencriptador, conecte el cable coaxial de entrada de 75 ohm a la caja para conversión o desencriptador. Con
otro cable coaxial de 75 ohm, conecte el enchufe de salida de la caja para conversión o desencriptador con el
enchufe de entrada RF de la unidad. Siga las conexiones como se muestra a continuación. Configure la unidad
con el canal de salida de la caja para conversión o desencriptador (por lo general, canal 3 o 4) y utilice la caja
para conversión o desencriptador para seleccionar los canales.
Enchufe de
entrada RF
Cable de entrada de 75 ohm
para la televisión por cable
Cable de 75 ohm al
unit
Convertidor/
Desencriptador
PARALOS SUSCRIPTORES AL SERVICIO BÁSICO DE TELEVISIÓN POR
CABLE SIN ENCRIPTAR CON CANALES PREMIUM ENCRIPTADOS
Si se suscribe a un servicio de televisión por cable en el cual los canales básicos no están encriptados y los
canales premium requieren el uso de una caja para conversión o desencriptador, probablemente desee utilizar
un divisor de señal y una caja de distribución A//B (disponible en la empresa de cable o en una tienda de
productos electrónicos). Siga las conexiones como se muestra a continuación. Con el interruptor en la posición
“B”, puede sintonizar directamente los canales sin encriptar de su unidad. Con el interruptor en la posición “A”,
sintonice su unidad según la salida de la caja para conversión o desencriptador (por lo general, canal 3 o 4) y
utilice la caja para conversión o desencriptador para sintonizar los canales encriptados.
Cable de entrada de
75 ohm para la
Convertidor/Desencriptador
televisión por cable
Cable de 75 ohm a la
unidad
Divisor
Interruptor A/B
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Configuración del idioma y de la pantalla azul
Puede elegir entre tres idiomas diferentes
(inglés, francés y español) para las
representaciones en pantalla.
1 Presione POWER ( ) (Encendido) para
encender el televisor.
2 Presione MENU y
luego presione el
botón VOL+/- para
seleccionar el menú
Funciones, luego
presione el botón CH-
para entrar.
FUNCIÓN
LENGUAJE
PANTALLA AZUL
NTSC SUBTÍTULOS C C1
DTV SUBTÍTULOS
CONTROL DE LOS PADRES
ESPANñOL
ENC.
3 Presione el botón CH -para seleccionar la opción
IDIOMA, luego presione VOL+/- para seleccionar el
idioma deseado: Inglés, francés o español
4 Presione MENU hasta que el menú desaparezca.
CONFIGURACIÓN DE LA PANTALLAAZUL
1 Presione MENU y
luego presione el
botón VOL+/- para
seleccionar el menú
Funciones, luego
presione el botón
CH- para entrar.
FUNCIÓN
LENGUAJE
PANTALLA AZUL
NTSC SUBTÍTULOS C C1
DTV SUBTÍTULOS
CONTROL DE LOS PADRES
ESPANñOL
ENC.
2 Presione el botón CH+/- para seleccionar la opción
PANTALLA AZUL, luego presione VOL+/- para
seleccionar Encendido o Apagado.
3 Presione MENU hasta que el menú desaparezca.
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLORACIÓN AUTOMÁTICA(DTV/ATV)
(Cuando se utiliza antena)
Los canales emitidos en DTV y ATV se exploran y
memorizan automáticamente. Sólo se memorizarán
los canales que se reciben en el área donde se utiliza
el televisor.
EXPLORACIÓN AUTOMÁTICA(CATV)
(Cuando se utiliza el servicio básico de cable)
Los canales emitidos en CATV se exploran y
memorizan automáticamente.
NOTA:
Asegúrese de que la antena o el cable estén conectados
correctamente antes de enchufar el cable de alimentación.
1 Presione MENU y luego presione el botón VOL+/-
para seleccionar el menú CANALES, luego presione
el botón CH- para entrar.
2 Presione el botón
CANAL
CH+/- para
seleccionar la
opción
CANAL No
SINTONIZADOR
SALTAR
29
ANTENA
APAG
BÚSQUEDA AUTO
RECEPCIÓN.
3 Presione el botón VOL+/- para seleccionar AIRE/CABLE.
4 Presione el botón CH +/-
para seleccionar la opción
B SQUEDA MANUAL.
5 Presione el botón VOL+ para comenzar la
exploración.
Cuando presiona VOL+ en el control remoto,
comenzará automáticamente la exploración de
canales, tanto en el modo analógico como digital.
Cuando se completa la exploración, aparecerá el
canal memorizado menor.
Cuando presione el botón MENU cuando se está
realizando la exploración, se interrumpe la
exploración y aparece el canal memorizado menor.
Download from Www.Somanuals.com. All Manuals Search And Download.
CONFIGURACIÓN DE LA OPCIÓN SALTEAR
Después de establecer previamente los programas,
puede saltear algunos programas para seleccionar sólo
sus canales favoritos.
1. Presione MENU y
CANAL
luego presione el botón
CANAL No
SINTONIZADOR
SALTAR
29
ANTENA
APAG
VOL+/- para seleccionar
el menú CANAL, luego
presione el botón CH-
para entrar.
BÚSQUEDA AUTO
2.Presione el botón
CH+/- para seleccionar
la opción SALTEAR,
luego presione VOL+/-
para seleccionar
Encendido o Apagado.
NOTA: Cuando sintonice canales de DTV y no haya señal,
estará disponible la opción SALTEAR y pasar al siguiente.
Si desea recuperar el canal que salteó
1. Use los botones con los dígitos correspondientes para
seleccionar el número de canal que desea recuperar.
2. Realice los pasos anteriores nuevamente.
3. Presione el botón VOL +/- para fijar SALTEAR como
Apagado.
CONFIGURACIÓN DEL SISTEMA DE COLOR
(sólo en modo ATV)
CANAL
CANAL No
SINTONIZADOR
SALTAR
BÚSQUEDA AUTO
1 Presione MENU y luego
29
ANTENA
APAG
presione el botón VOL+/-
para seleccionar el menú
CANAL, luego presione el
botón CH- para entrar.
Download from Www.Somanuals.com. All Manuals Search And Download.
Puede seleccionar el canal utilizando el botón CH +/- o los
botones con los números de los canales. A continuación se
muestra cómo se debe seleccionar el canal de cada una de
estas maneras.
1 Utilizando el botón CH +/-
- Utilizando el botón CH +/- del control remoto, cambie el canal.
- Puede realizarse la misma operación con el botón CH +/- del
panel de adelante de la unidad principal.
2
Presione los botones para la selección directa de canales para
seleccionar el canal.
Modo de Antena Selección directa de canales
Cuando la opción del menú de Antena/Cable está en la posición Antena,
todos los canales pueden seleccionarse instantáneamente utilizando los
botones con los números. Ejemplo:
2-9: Presione 2-9 según sea necesario.
Por ejemplo, para seleccionar canal 2, presione “2”.
10-69: Presione los dos dígitos en orden. Si selecciona un canal superior a
69, no se cambiará el canal, ya que no está disponible.
Modo de CABLE Selección directa de canales
Cuando la opción del menú Antena/Cable está en la posición Cable, los
canales pueden seleccionarse de la siguiente manera:
1-9: Presione 1-9 según sea necesario. Por ejemplo, para seleccionar el
canal 2, presione "2".
10-99: Presione los 2 dígitos en orden Por ejemplo, para elegir el canal 32,
presione “3” y después “2”.
100-125: Presione el botón con el dígito 1, en la pantalla aparecerá "1- ",
luego presione los dos dígitos restantes en orden.
CABLE
TV
VHF
2-13
VHF
2-13
UHF
14-69
STD/HRC/IRC
14-36
(A) (W)
37-59
(AA) (WW)
60-85
(AAA) (ZZZ)
86-94
(86) (94)
95-99
(A-5) (A-1)
100-125
(100) (125)
01
(5A)
NOTA:
En la emisión de DTV, un mismo canal algunas veces emite varios
programas, según el tiempo de aire. En este caso, el canal principal
se llama “canal principal” y el subcanal se llama “canal secundario”.
Download from Www.Somanuals.com. All Manuals Search And Download.
Esta sección describe cómo debe ajustarse el volumen cuando se
mira televisión. También se describirá la función SIN SONIDO,
que es útil cuando tiene visitas o una llamada telefónica.
1
Utilizando el botón VOL +/-
- Puede ajustar el volumen del audio con el botón VOL +/-del
control remoto.
- Aparece la barra del volumen en la parte inferior de la pantalla
cuando ajusta el volumen.
- Puede realizarse la misma operación con el botón VOL +/- del
panel de adelante de la unidad principal.
2 Uso del botón MUTE (SIN SONIDO
- Presione el botón MUTE (SIN SONIDO) del control remoto para
detener el sonido.
La barra coloreada de volumen aparece en la pantalla mientras el
televisor está en el modo sin sonido.
- Para salir del estado SIN SONIDO, presione el botón MUTE
nuevamente o presione el botón VOL+.
Se mostrará de manera continua SIN SONIDO cuando los
subtítulos ocultos están apagados, SIN SONIDO desaparecerá
después de 5 segundos cuando los subtítulos ocultos están
encendidos.
CAMBIOS EN EL AUDIO
Esta sección describe cómo cambiar el idioma del audio en el
modo digital.
2 Cambio del idioma de audio.
- Cuando presiona el botón SAP (Programa de audio secundario)
del control remoto, en la pantalla aparecerán el idioma
seleccionado en ese momento y la cantidad de idiomas recibidos.
- Cada vez que presione el botón SAP (Programa de audio
secundario) en el control remoto, se cambiará el idioma.
- Los idiomas entre los que puede elegir varían según la emisión
recibida.
NOTA:
La función del botón SAP sólo funciona con algunos canales de
televisión y no funciona con equipos externos, tales como
reproductores de DVD.
Download from Www.Somanuals.com. All Manuals Search And Download.
Información en pantalla
Puede desplegar en la pantalla el número de canal
seleccionado en un momento determinado u otra información,
como el modo de audio, para su control.
En el modo analógico, se muestran el número de canal
seleccionado y el modo de audio.
1 Despliegue el número de canal y el modo de audio.
- Presione el botón INFO en el control remoto. En la parte
superior derecha de la pantalla aparecen el número de canal
y el modo de audio seleccionados.
- Para limpiar la pantalla, presione el botón INFO nuevamente.
En el modo digital, se muestra la información detallada del
canal seleccionado en ese momento, como la GUÍA de
programas.
Información detallada del canal.
- Cada vez que presiona el botón INFO, se cambiará el modo
de lo que aparece en pantalla como se muestra a continuación.
INFORMACIÓN
5
6
11-1
[1920*1080]
1
MBC DTV
2
3
4
NO PROGRAM INFO
SIN CC INFO
SIN CLASIFICACION
16:9
DESCONOCIDO
07:19-09:56
7
8
SIN INFORMACION DEL PROGRAM
9
NOTAS:
Cuando la guía de programas que se despliega es de más de 6 líneas,
utilice el botón VOL+/- y recorra la lista para poder leerla.
Cuando no se proporciona la guía de programas, aparece "no se
proporciona descripción".
Download from Www.Somanuals.com. All Manuals Search And Download.
CONFIGURACIÓN DE VIDEO
1. Presione el botón MENU. Aparecerá la pantalla
con el menú principal.
2. Presione el botón
IMAGEN
VOL+/- para seleccionar
la opción IMAGEN, luego
presione el botón CH-
BRIGHTNESS
para entrar.
CONTRAST
80
80
50
50
SHARPNESS
COLOR
TINT
+00
3. Presione el botón CH +/- para seleccionar la opción deseada
y luego presione el botón VOL +/- para ajustar.
Contraste
Esta opción le permite ajustar la intensidad de las partes
brillosas de la imagen, pero deja las partes oscuras sin
cambios.
Brillo
Esta opción ajusta la salida de luz de toda la imagen, lo que
afecta principalmente las áreas más oscuras de la imagen.
Color
Esta opción ajusta el nivel de saturación de los colores para
que coincida con sus preferencias personales.
Nitidez
Esta opción ajusta la nitidez de los detalles finos de la imagen.
Tinte
Le permite seleccionar la mezcla de colores (Tinte) de la
imagen.
Download from Www.Somanuals.com. All Manuals Search And Download.
CONFIGURACIÓN DEL AUDIO
1 Presione el botón MENU. Aparecerá la pantalla con el
menú principal.
SONIDO
2 Presione el botón
VOL+/- para seleccionar la
VOLUMEN
BALANCE
80
+00
opción SONDIO, luego
presione el botón CH- para
entrar.
3 Presione el botón CH +/- para seleccionar una opción y
luego presione el botón VOL +/- para ajustar.
Volumen
Para ajustar el nivel de salida del sonido.
Equilibrio
Para ajustar el equilibrio de salida del sonido.
Download from Www.Somanuals.com. All Manuals Search And Download.
EJEMPLO: Configuración de la hora "8:30 AM”
Para utilizar el temporizador de
encendido/apagado, debe configurar
Manualmente la hora.
PARACONFIGURAR LA HORA
1 Presione MENU. Aparecerá la pantalla con el menú principal.
HORA
2 Presione el botón
VOL+/- para
HORA
--:-- AM
--:-- AM
--:--AM
ENC
seleccionar la opción
HORA, luego presione
el botón CH- para
ENCENDER
APAGAR
HORARIO VERANO
ZONA
entrar al submenú.
ALASKA
3 Presione el botón CH+/- para seleccionar HORA, luego
presione el botón CH+/- para seleccionar "--:--","AM";
presione el botón VOL+/- para configurar el valor AM o PM.
4 Presione MENU hasta que el menú desaparezca.
NOTA:
Después de un corte del suministro de energía o después de
que se desconecta la energía, se pierde la hora configurada. En
tal caso, vuelva a configurar la hora.
Download from Www.Somanuals.com. All Manuals Search And Download.
Esta función le permite que el televisor se
encienda o se apague automáticamente a una
hora predeterminada. Si programa el
temporizador de encendido/apagado,
el televisor se encenderá o se apagará
a la hora que predeterminó.
CONFIGURACIÓN PARAENCENDIDO DEL
TEMPORIZADOR
1 Presione MENU. Aparecerá la pantalla con el menú
principal.
HORA
2 Presione el botón
VOL+/- para seleccionar
HORA
--:-- AM
la opción HORA, luego
presione el botón CH-
para entrar al submenú.
ENCENDER
APAGAR
--:-- AM
--:--AM
ENC
HORARIO VERANO
ZONA
ALASKA
3 Presione el botón CH+/- para seleccionar HORA de
APAGAR, luego presione el botón CH+/- para seleccionar
"--:--","AM"; presione el botón VOL+/- para configurar la
hora.
4 Presione MENU hasta que el menú desaparezca.
CONFIGURACIÓN PARAAPAGADO DEL
TEMPORIZADOR
1 Presione MENU. Aparecerá la pantalla con el menú
principal.
2 Presione el botón
HORA
VOL+/- para seleccionar
la opción HORA, luego
presione el botón CH-
para entrar al submenú.
HORA
--:-- AM
--:-- AM
--:-- AM
ENC
ENCENDER
APAGAR
HORARIO VERANO
ZONA
ALASKA
3 Presione el botón CH+/- para seleccionar HORA de
ENCENDER, luego presione el botón CH+/- para
seleccionar "--:--","AM"; presione el botón VOL+/- para fijar
el valor.
4 Presione MENU hasta que el menú desaparezca.
Download from Www.Somanuals.com. All Manuals Search And Download.
CONFIGURACIÓN DEL SUBTITULADO EN NTSC
Esto le permite configurar la manera en que elije
visualizar el subtitulado.
1. Presione el botón MENU y luego utilice el botón VOL +/-
para seleccionar el menú FUNCIÓN.
2. Presione el botón CH-
FUNCIÓN
para entrar, luego
LENGUAJE
PANTALLA AZUL
NTSC SUBTÍTULOS C C1
DTV SUBTÍTULOS
ESPANñOL
ENC.
presione el botón
CH+/- para seleccionar
NTSC TÍTULO.
CONTROL DE LOS PADRES
3. Luego use el botón VOL+/-para seleccionar subtitulado:
APAGADO, C1, C2, SUBTITULADO SIN SONIDO,
TEXTO1, TEXTO2.
También puede presionar el botón CC (subtítulos ocultos)
del control remoto para seleccionar el modo de subtitulado
que desea.
4. Cuando esté satisfecho con su elección, presione el
botón MENU para volver al menú anterior.
SUBTITULADO
Se utiliza para referirse a las palabras que se
reproducen en la parte inferior de la pantalla del
televisor; por lo general, se trata de la parte de audio
del programa que se proporciona para los
discapacitados auditivos.
TEXTO
Término para designar las palabras que aparecen en un
marco negro grande y cubren casi toda la pantalla, por lo
general son los mensajes que proporciona la emisora.
Download from Www.Somanuals.com. All Manuals Search And Download.
P u e d e configurarse una limitación
de la edad para prohibir a los niños ver
y oír escenas violentas o imágenes
para adultos, etc. El televisor se remite
a “CLASIFICACIÓN PARA
TELEVISIÓN" y “CLASIFICACIÓN DE
PELÍCULAS”. Para utilizar la función de
control infantil, debe registrar un código.
PARAREGISTRAR UN CÓDIGO
1 Presione MENU. Aparecerá la pantalla con el menú principal.
2 Presione el botón VOL+/-
para seleccionar la opción
FUNCIÓN, luego presione
el botón CH- para entrar al
submenú.
FUNCIÓN
LENGUAJE
PANTALLA AZUL
NTSC SUBTÍTULOS C C1
DTV SUBTÍTULOS
ESPANñOL
ENC.
CONTROL DE LOS PADRES
3 Presione el botón CH+
para seleccionar la opción
SEGUR.DEL PADRES,
luego presione el botón
VOL+ para entrar al
submenú.
INGRESE CLAVEDE ACCESO
----
4 Introduzca el código (de
4 dígitos) utilizando los
botones con los números
(0-9). El televisor se
configura con el código
inicial 0000.
CONTROL DE LOS PADRES
CLAS MPAA.
GUÍA DE PADRES
CLAS CA ENG
CLAS CA FRAN
CLASIF DIGITAL
5 Después de introducir el
código correctamente,
presione CH+/- para
seleccionar el elemento
deseado.
CLASIF DIGITAL
CONTROL DE LOS PADRAPAG
CHANGE CONTRASEÑA
NOTAS:
Si olvida el código, no podrá configurar el Control infantil. Para
evitar olvidarse el código, escríbalo y guárdelo en un lugar
seguro.
Download from Www.Somanuals.com. All Manuals Search And Download.
PARACAMBIAR EL CÓDIGO
1 Presione MENU. Aparecerá la pantallacon el menú
principal.
FUNCIÓN
2 Presione elbotón VOL+/-
LENGUAJE
PANTALLA AZUL
NTSC SUBTÍTULOS C C1
DTV SUBTÍTULOS
CONTROL DE LOS PADRES
ESPANñOL
ENC.
para seleccionar laopción
FUNCIÓN, luego presioneel
botón CH- paraentrar al
submenú.
3 Presione elbotón CH+
para seleccionar laopción
SEGUR.DEL PADRES,
luego presione elbotón
VOL+ para entrar al
submenú.
INGRESE CLAVEDE ACCESO
----
4 Introduzca elcódigo (de 4
dígitos) utilizando los
botones con losnúmeros (0-
9).
CONTROL DE LOS PADRES
CLAS MPAA.
GUÍA DE PADRES
CLAS CA ENG
CLAS CA FRAN
CLASIF DIGITAL
CLASIF DIGITAL
5 Presione CH+ para
seleccionar CAMBIO DE
CÓDIGO, luego presione
VOL+ para entrar al
submenú.
CONTROL DE LOS PADRAPAG
CHANGE CONTRASEÑA
6 Introduzca elcódigo nuevo
utilizando los botones con
los números (0-9).
NUEUA CONTRASEÑA
0000
7 Introduzca nuevamenteel código nuevo.
NOTAS:
Si olvida el código, no podrá
configurar el Control infantil.
Para evitar olvidarse el código,
escríbalo y guárdelo en un lugar
seguro.
8 Presione MENU hasta que elmenú desaparezca.
Download from Www.Somanuals.com. All Manuals Search And Download.
PARAENCENDER O APAGAR EL CONTROL
INFANTIL
1 Entre al menú CONTROL INFANTIL.
CONTROL DE LOS PADRES
CLAS MPAA.
GUÍA DE PADRES
CLAS CA ENG
CLAS CA FRAN
2 Presione el botón CH+/-
para seleccionar
SEGUR.DEL PADRES,
luego presione VOL+/- para
seleccionar Encendido o
Apagado.
CLASIF DIGITAL
CLASIF DIGITAL
CONTROL DE LOS PADRAPAG
CHANGE CONTRASEÑA
3 Cuando esté satisfecho con su elección, presione el botón
MENU (MENÚ) para volver al menú anterior.
PARACONFIGURAR LA GUÍA PARA PADRES
1 Entre al menú CONTROL INFANTIL.
2 Presione el botón CH+/-
para seleccionar la opción
GUÍA DE PADRES, luego
presione el botón VOL+/-
para entrar al submenú.
CONTROL DE LOS PADRES
CLAS MPAA.
GUÍA DE PADRES
CLAS CA ENG
CLAS CA FRAN
CLASIF DIGITAL
CLASIF DIGITAL
CONTROL DE LOS PADRAPAG
CHANGE CONTRASEÑA
3 Presione los botones CH+/-
/VOL+/- para elegir las
clasificaciones deseadas.
PARENTAL GUIDE
4 Cuando esté satisfecho con
su elección, presione el
botón MENU para volver al
menú anterior.
ALL FV
D
L
S
V
NONE
TV-Y
TV-Y7
TV-G
TV-PG
TV-14
TV-MA
Clasificación de programas de televisión incluyendo las películas hechas para
televisión:
TV-Y
TV-Y7 (Niños mayores de 7 años)
TV-G (Audiencia general)
TV-PG (Se recomienda el acompañamiento de un adulto)
TV-14 (Advertencia importante para los padres)
(Todos los niños)
TV-MA (Audiencia adulta solamente)
Cómo utilizar el televisor cuando se ha
activado el Control infantil.
Clasificación de la televisión para los niños:
ALL (Todas las edades) (se aplica aTV-Y, TV-Y7)
FV (Violencia fantástica) (se aplica a TV-Y7)
Cuando se recibe el programa que se aplica
a la configuración Control infantil, introduzca
el código. Cuando se introduce el código
correctamente, se suspende la protección
de forma temporal.
Clasificación de la televisión en general
ALL (Todas las edades)
(se aplica a TV-G, TV-PG, TV-14, TV-MA)
D (Diálogo, diálogo sexual)
L (Lenguaje, lenguaje adulto)
(se aplica a TV-PG, TV-14)
(se aplica a TV-PG, TV-14, TV-MA)
NOTA:
La función de Control infantil se activa sólo con los
programas y las cintas que son compatibles con la
clasificación.
S (Sexo, situaciones sexuales) (se aplica a TV-PG, TV-14, TV-MA)
V (Violencia) (se aplica a TV-PG,TV-14, TV-MA)
Download from Www.Somanuals.com. All Manuals Search And Download.
CÓMO CONFIGURAR LA CLASIFICACIÓN MPAA
1 Entre al menú CONTROL INFANTIL.
2 Presione el botón CH+/-
para seleccionar
CONTROL DE LOS PADRES
CLAS MPAA.
GUÍA DE PADRES
CLAS CA ENG
CLAS CA FRAN
CLASIF DIGITAL
CLASIFICACIÓN MPAA,
luego presione el botón
VOL+ para entrar al
submenú.
CLASIF DIGITAL
CONTROL DE LOS PADRAPAG
CHANGE CONTRASEÑA
3 Presione el botón CH+/-
para seleccionar la
clasificación deseada.
Clasificación de películas previamente emitidas en cines:
Clasificación de películas
NR
G
(Permite todos los programas)
(Audiencia general)
PG
(Se recomienda el
CLAS.MPAA
N/A
G
PG
PG-13
R
acompañamiento de un adulto)
PG-13 (Advertencia importante para los
padres)
R
(Restringida)
NC-17 (Prohibida para menores de 17)
(Sólo para adultos)
X
NC-17
X
Si configura PG-13, están disponibles las
películas G y PG; las películas PG-13, R,
NC-17 y X estarán bloqueadas.
4 Presione el botón VOL+/- para seleccionar borrar o v.
5 Presione MENU hasta que el menú desaparezca.
Download from Www.Somanuals.com. All Manuals Search And Download.
Subtítulos: Este modo de subtítulos ocultos muestra el
texto en la pantalla en inglés o en otro idioma (según la
configuración de los subtítulos ocultos).
Por lo general, los subtítulos ocultos en inglés se
transmiten en los subtítulos CC 2.
Texto: El modo de subtítulos ocultos de texto por lo
general llena la pantalla con los horarios de programación
u otra información. Después de seleccionar un modo de
subtítulos ocultos, éste seguirá en efecto hasta que se lo
cambie, aunque se cambie de canal. Si se pierde la señal
de los subtítulos a causa de las publicidades o una
interrupción de la señal, volverán a aparecer los subtítulos
cuando se reciba nuevamente la señal. Si se cambian los
canales, los subtítulos se retrasarán aproximadamente 10
segundos. Los subtítulos aparecen en lugares de la
pantalla donde interfieran menos con la imagen, por lo
general en la parte inferior de la pantalla. Los programas
de noticias por lo general cuentan con subtítulos de tres
líneas que se desplazan por la pantalla. La mayoría de los
demás programas proporcionan subtítulos de dos o tres
líneas ubicados cerca del personaje que habla, así el
televidente puede seguir el diálogo. Las palabras en
cursiva o subrayadas se utilizan para los títulos, las
palabras en idiomas extranjeros o las palabras que
requieren énfasis. Las palabras cantadas por lo general
aparecen entre notas musicales. Para conocer la emisión
con subtítulos ocultos de programas de televisión, busque
en la GUÍA DE TELEVISIÓN el símbolo de los subtítulos
ocultos (CC).
NOTAS:
Cuando seleccione los subtítulos ocultos, el subtitulado tendrá un retraso de aproximadamente 10
segundos.
Si no se recibe señal de subtítulos, no aparecerán los subtítulos, pero el televisor seguirá en el modo
subtítulos.
Durante la reproducción de los subtítulos ocultos, pueden aparecer ocasionalmente palabras mal
escritas o caracteres inusuales. Esto es normal para el subtitulado oculto, especialmente con los
programas en vivo. Esto sucede porque durante los programas en vivo, los subtítulos también se
introducen en vivo. Estas transmisiones no dan tiempo a la edición.
Cuando se muestran los subtítulos, las representaciones en pantalla, como por ejemplo el volumen y
el modo sin sonido pueden estar ocultas. Si aparece la representación en pantalla, desaparecen los
subtítulos ocultos, cuando desaparece la representación en pantalla, los subtítulos ocultos aparecen
nuevamente.
Algunos sistemas de cable y sistemas de protección contra copias pueden interferir con la señal de
subtítulos ocultos.
Si utiliza una antena interior o si la recepción del televisor es deficiente, el decodificador de subtítulos
ocultos puede no aparecer o puede aparecer con caracteres extraños o palabras mal escritas. En tal
caso, ajuste la antena para que la recepción sea mejor o utilice una antena
Download from Www.Somanuals.com. All Manuals Search And Download.
CONFIGURACIÓN DEL MODO DE SUBTÍTULOS OCULTOS
En modo DTV
1 Presione MENU. Aparecerá la pantalla con el menú
principal.
2 Presione el botón
FUNCIÓN
VOL+/- para
LENGUAJE
PANTALLA AZUL
NTSC SUBTÍTULOS C C1
DTV SUBTÍTULOS
CONTROL DE LOS PADRES
ESPANñOL
ENC.
seleccionar DTV
SETUP luego
presione CH- para
entrar al submenú.
3 Presione el botón
CH+/- para
seleccionar DTV
CC.
DTV SUBTÍTULO
SUBTÍTULO
ESTILO
TAMAO
COLOR DE TEXTO
OPACIDAD DETEXTO AUTO
COLOR DE FONDO
OPACIDAD DOUNDO
TIPO DE BORDE
COLOR DE BORDES
RE INICLAR
APAG
4 Presione el botón
VOL+ y luego presione
el botón CH+/- para
seleccionar el MODO
DEL SUBTÍTULADO.
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
5 Presione el botón
VOL+ y luego presione
el botón VOL+/-para
seleccionar subtítulos
ocultos “Apagados” o
“Encendidos”.
Durante la configuración,
la opción DTVCC
(Subtítulos ocultos en
DTV) estará disponible.
6 Presione el botón
CH+/- para seleccionar
DTV CC y presione
VOL+/- para configurar
el servicio deseado.
CONFIGURACIÓN DE DTV CC (SUBTÍTULOS OCULTOS EN DTV)
Esto le permiteconfigurar la maneraen que elije visualizar el subtituladodigital.
Seleccione uno delos canales deservicio digital quepone a disposiciónel proveedor de
subtitulados.
Existen 6 serviciosestándar. Elservicio 1 sedenomina Servicio de
Subtitulado Primario. Esteservicio contiene lossubtítulos palabra porpalabra, o casi, del
idioma original quese habla enel audio que acompaña al programa.
El servicio 2se denomina Serviciode Subtitulado Secundario.
Este servicio contienesubtitulados en unsegundo idioma, queson la traducciónde un
subtitulado en elServicio de Subtituladoprimario.
Los demás subcanalesde servicio noestán asignados previamente. La utilización delos
canales de serviciorestantes depende dela discreción delproveedor.
Download from Www.Somanuals.com. All Manuals Search And Download.
Menú de configuración de DTV
CONFIGURACIÓN DEL MODO DE USUARIO
CON SUBTÍTULOS OCULTOS (CC)
1 Presione MENU. Aparecerá la pantalla con el menú
principal.
2 Presione el botón
VOL+/- para
DTV SUBTÍTULO
SUBTÍTULO
ESTILO
TAMAO
COLOR DE TEXTO
APAG
AUTO
AUTO
AUTO
seleccionar
CONFIGURACIÓN DE
DTV luego presione
CH- para entrar al
submenú.
3 Presione el botón
CH+/- para
seleccionar DTV CC
(Subtítulos ocultos en
DTV).
OPACIDAD DETEXTO AUTO
COLOR DE FONDO
OPACIDAD DOUNDO
TIPO DE BORDE
COLOR DE BORDES
RE INICLAR
AUTO
AUTO
AUTO
AUTO
AUTO
4 Presione el botón VOL+ y luego presione el botón CH+/-
para seleccionar CONFIGURACIÓN DEL USUARIO.
5 Presione el botón VOL+/- para configurar "EMISIÓN" o
“PERSONAL".
Download from Www.Somanuals.com. All Manuals Search And Download.
CONFIGURACIÓN DEL ESTILO DE SUBTITULADO
EN DTV (continuación)
Estilo
Seleccione esta opción para elegir el estilo de la fuente de los
subtítulos que aparecen en pantalla según sus preferencias.
Presione el botón VOL+/- para seleccionar Estilo1, Estilo2, Estilo3,
Estilo4, Estilo5, Estilo6, Estilo7, Estilo8.
Tamaño
Seleccione esta opción para elegir la fuente de los subtítulos que
aparecen en pantalla según sus preferencias.
Presione el botón VOL+/-para seleccionar Pequeño, Normal o
Grande,
Color del texto
Seleccione esta opción para elegir el color del texto o la opacidad
del cuadro con los subtítulos según sus preferencias. Seleccione un
color y una de las opciones de opacidad.
Opacidad del texto: Especifique la opacidad del color del texto.
Color del fondo: Para seleccionar el color del fondo.
Opacidad del fondo: Especifique la opacidad del color del fondo.
Download from Www.Somanuals.com. All Manuals Search And Download.
Menú de configuración de DTV
CONFIGURACIÓN PARAEL AHORRO DE ENERGÍA
La hora para el ahorro de energía se fija
automáticamente con señales emitidas especialmente.
Este elemento del menú le permite desactivar la
configuración automática de tiempo de ahorro de energía.
Esto es útil si vive en una zona o estado donde no se aplica
el ahorro de energía, pero recibe canales de otras áreas
donde se emiten señales de ahorro de energía.
1 Presione MENU. Aparecerá la pantalla con el menú
principal.
HORA
2 Presione el botón
VOL+/- para seleccionar
HORA
--:-- AM
--:-- AM
--:--AM
ENC
la opción HORA, luego
presione el botón CH-
para entrar.
ENCENDER
APAGAR
HORARIO VERANO
ZONA
ALASKA
3 Presione el botón CH+/-
para seleccionar
AHORRO DE ENERGÍA, luego presione el botón VOL+/-
para seleccionar ENCENDIDO para la corrección
automática del reloj para el ahorro de energía, basada en
señales especialmente emitidas. Seleccione Apagado
para deshabilitar la corrección automática del reloj
basada en señales especialmente emitidas.
CONFIGURACIÓN DE LA ZONA HORARIA
Esta función le permite seleccionar la zona horaria en la que
se encuentra. La información de hora emitida corregirá el
reloj según su hora local.
1 Presione MENU.
Aparecerá la pantalla
con el menú principal.
2 Presione el botón
VOL+/- para
seleccionar la opción
HORA, luego presione el
botón CH- para entrar.
HORA
HORA
--:-- AM
--:-- AM
--:--AM
ENC
ENCENDER
APAGAR
HORARIO VERANO
ZONA
ALASKA
3 Presione el botón CH +/- para elegir la opción ZONA
HORARIA.
4 Presione el botón VOL+/- para seleccionar la zona horaria
del área donde vive: NEWFOUNDLAND, ATLÁNTICO,
ESTÁNDAR, CENTRAL, MONTAÑA, PACÍFICO,
ALASKA, HAWAII, o SAMOA
Download from Www.Somanuals.com. All Manuals Search And Download.
Otras funciones
GUÍA
- Activa algunas, aunque no todas, guías electrónicas de
programas cuando las utilizan y transmiten algunos
proveedores de estaciones de DTV. Sólo es compatible con
la recepción de canales DTV.
GUÍA
1/3 >>
03:00 ---04:00
Imagen en movimiento
480i 4:3
04:00 ---05:00
Imagen en movimiento
480i 4:3
1. Presione el botón GUIDE (GUÍA) para encender la guía.
2. Presione el botón CH+/- o VOL+/-para seleccionar el
programa deseado, luego presione el botón OK (Aceptar)
para que se muestre el programa seleccionado.
3. Presione el botón GUIDE (GUÍA) o EXIT (SALIR)
nuevamente para apagar la guía y volver a la
visualización de la televisión.
LISTADE CANALES FAVORITOS
Usted puede crear su propia Lista de Favoritos. Utilice el
botón FAV.LIST (LISTA DE FAVORITOS) del control remoto
cuando un canal esté resaltado y entonces podrá agregar o
borrar el canal de la Lista de Favoritos.
LISTA DE CANAL
14.3
ATSC-3
[TECLA ACEPTAR] AGREGAR CANAL ACTUAL
A LA LISTA DE FAVORITOS
Presione el botón FAV.LIST para abrir la lista de
canales favoritos, presione el botón CH+/- para
seleccionar el canal y presione el botón OK (Aceptar)
para confirmar.
Download from Www.Somanuals.com. All Manuals Search And Download.
VISUALIZACIÓN RÁPIDA
Esta función le permite ir rápidamente al último programa
que se miró.
1 Por ejemplo, el número de canal que
usó último es el 8 y el canal que está
usando es el 18 (como se muestra en
la figura).
2 Si desea volver al canal 8, que es el
último programa que se miró,
simplemente presione el botón Q.View
(Visualización rápida).
3 Si desea volver al canal 18, presione
el botón nuevamente. Con el uso de
esta función, puede cambiar
fácilmente del canal que está
utilizando al canal que miró antes.
TEMPORIZADOR DE DESCONEXIÓN AUTOMÁTICA
Para configurar el televisor para que se apague después de
una cantidad de tiempo prefijada, presione el botón SLEEP
(DESCONEXIÓN AUTOMÁTICA) varias veces para
seleccionar
la cantidad de minutos.
En primer lugar, aparece la
opción APAGADO en la
pantalla, seguida de las
siguientes opciones para el
temporizador de desconexión
Automática:
DORMIR:APAG
(5 MIN, 10 MIN, 15 MIN, 30 MIN, 45 MIN, 60 MIN,90 MIN,
120 MIN, 180 MIN, 240 MIN, APAGADO)
Para confirmar la configuración del temporizador de
desconexión automática, presione SLEEP (DESCONEXIÓN
AUTOMÁTICA). Se mostrará el tiempo restante durante
unos pocos segundos. Para cancelar el temporizador de
desconexión automática, presione SLEEP (DESCONEXIÓN
AUTOMÁTICA) varias veces hasta que se apague.
MODO DE LA IMAGEN
Cada vez que presiona el botón
P.MODE (MODO DE LA IMAGEN),
se cambia el modo de calidad de
la imagen deseado. Hay cuatros
modos de imagen (“SUAVE”,
“ERTÁNDAR”, “INTENSO”,
SUAVE
“PERSONALIZAR”) que pueden
seleccionarse de a uno.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
TCR13-A
TCR20-A
TCF20-A
TCR13-A
TCR20-A
TCF20-A
Download from Www.Somanuals.com. All Manuals Search And Download.
Garantía
Los productos de marca Haier, cuando son
enviados en su embalaje original, no deben
tener mano de obra o materiales defectuosos,
y Haier asume que, según sea su decisión,
reparará el defecto o reemplazará el producto
defectuoso con uno nuevo o un equivalente
vuelto a fabricar sin gastos para el comprador
por las piezas o la mano de obra, durante los
períodos establecidos a continuación.
Haier con el comprador en relación con el
producto, y constituirá el resarcimiento completo
de todos los reclamos, ya sean basados en
contrato, negligencia, responsabilidad estricta u
otros. En ningún caso será responsable Haier, de
ninguna manera, por los daños o defectos en el
producto que fueron provocados por
reparaciones o intentos de reparaciones
realizadas por personas que no sean un centro
de reparaciones autorizado o vendedor. Tampoco
será responsable Haier, de ninguna manera, por
los daños fortuitos o económicos consecuentes,
ni por los daños a los bienes. Algunos estados
no permiten la exclusión de los daños
Esta garantía no se aplica a la apariencia del
producto ni al exterior del mismo, que haya
sido dañado, estropeado, alterado o
modificado en el diseño o la construcción. No
se aplica a los elementos adicionales
excluidos establecidos a continuación.
consecuentes o fortuitos, de modo que la
limitación anterior puede no aplicarse en su
caso.
Esta garantía comienza el día de la compra
del artículo. Se le debe presentar al
representante de reparaciones autorizado el
recibo original de la compra antes de
realizarse las reparaciones cubiertas por la
garantía.
ESTAGARANTÍA LE CONCEDE
DERECHOS LEGALES ESPECÍFICOS.
TAMBIÉN PUEDE TENER OTROS DERECHOS,
QUE VARÍAN DE UN ESTADO A OTRO.
Período de garantía de este producto: 90 días
para la mano de obra y un año para las piezas.
Elementos adicionales excluidos de la
cobertura de la garantía: pilas no recargables.
Lugares donde obtener servicio: Para conocer la
ubicación del centro de reparaciones Haier más
cercano o para obtener información impresa
sobre productos, accesorios, suministros o
asistencia al cliente, llame al 1-877-337-3639.
Qué debe hacer para obtener servicio de
reparaciones: envíe o lleve su producto a un
proveedor o centro autorizado de reparaciones.
Asegúrese de contar con el comprobante de
compra.
Esta garantía limitada descrita en el presente
se suma a las garantías implícitas que puedan
otorgarse a los compradores por ley. TODAS
LAS GARANTÍAS IMPLÍCITAS INCLUYENDO
LAS GARANTÍAS DE COMERCIABILIDAD E
IDONEIDAD PARAEL USO SE LIMITANAL
PERÍODO O A LOS PERÍODOS QUE SE
CUENTANA PARTIR DE LA FECHADE
COMPRA ESTABLECIDOS A
CONTINUACIÓN. Algunos estados no
permiten limitaciones en cuanto a la duración
de la garantía, de modo que las limitaciones
mencionadas anteriormente pueden no
aplicarse a su caso.
Si envía el producto, asegúrese de que esté
cuidadosamente embalado.
Haier America
Nueva York, NY10018
Ni el personal de ventas del vendedor ni
ninguna otra persona está autorizada a
otorgar garantías que no sean las descritas en
el presente, ni a prolongar la duración de las
garantías con posterioridad al período descrito
en el presente en nombre de Haier.
Las garantías descritas en el presente serán
las garantías únicas y exclusivas otorgadas
por Haier y representarán el recurso único y
exclusivo disponible al comprador. La
corrección de defectos de la manera y por el
tiempo descrito en el presente constituirá el
cumplimiento completo de todas las
obligaciones y responsabilidades de
Download from Www.Somanuals.com. All Manuals Search And Download.
0090500177F
6
Download from Www.Somanuals.com. All Manuals Search And Download.
|