Model C100/110 Owner’s Guide
®
HEWLETT
PACKARD
HP Part No. A4200-90014
Edition E0995
Printed in U.S.A.
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Contents
Preface xvii
1 System Overview
Product Description 3
System Unit Front Panel Controls and LEDs5
System Power Switch
6
Power LED
6
System LEDs
6
Audio Controls
7
Removable Storage Devices
7
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
System Unit Rear Panel Connectors
8
Security Loop
9
Audio Connectors 10
Keyboard Connectors 12
HP Parallel I/O Connector 12
802.3 Network Connectors 12
Serial I/O Connectors 12
SCSI Connectors 13
TOC Button 14
Power Cord Connector 14
Monitors 15
Keyboards 16
Keyboard Differences 16
Pointing Devices 19
Operating System Overview 20
Important Information You Need to Note 21
LANIC ID 21
SCSI ID and Device File Information for HP-UX 9.05 23
SCSI ID and Device File Information for HP-UX 10.0 23
Networking Overview 25
Mail 25
telnet 25
rlogin 26
ftp 26
rcp 26
NFS 26
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
2 Setting Up Your Printer
Gathering Printer Information 29
Setting Up a Local Printer Using SAM 30
Setting Up Your Printer for Network Printing 35
Printing a File 37
Solving Printer Problems 38
3 Using Your CD-ROM Drive
CD-ROM Drive and CD-ROM Media Descriptions 41
CD-ROM Drive 41
CD-ROM Media 44
Operating the CD-ROM Drive 45
Loading and Unloading a CD-ROM in the Disc Tray 45
Verifying the CD-ROM Drive Operation 51
Using Device Files 53
Mounting and Unmounting a CD-ROM Disc 54
Mounting a CD-ROM Disc Using SAM 54
Unmounting a CD-ROM Disc Using SAM 57
Reading the Busy Light 59
Troubleshooting 61
v
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
4 Using Your Digital Data Storage (DDS) Tape Drive
DDS Tape Drive and Data Cassette Descriptions 65
DDS Drive 65
Data Cassettes 68
Setting the Write-Protect Tab on a Data Cassette 69
Operating the DDS Tape Drive 71
Loading and Unloading a Data Cassette 71
Verifying the DDS Tape Drive Operation 72
Using Device Files 73
Archiving Data in Compressed and Noncompressed Mode 74
Writing to a Data Cassette 74
Restoring Files from a Data Cassette to Your System 75
Listing the Files on a Data Cassette 75
Further Command Information 76
Media Interchangeability Restrictions 76
Troubleshooting 77
Ordering Information 78
vi
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
5 Using Your 3.5-Inch Floppy Disk Drive
Using the Floppy Diskette 81
Setting the Write-Protect Tab on a Diskette 81
Inserting and Removing a Diskette 82
Operating the Floppy Drive 83
Verifying the Floppy Drive Configuration 83
Using Device Files 84
Formatting a New Diskette 85
Transferring Data To and From a Floppy Diskette 86
Saving Files to a Floppy Diskette 86
Restoring Files from a Floppy Diskette to Your System 87
Listing the Files on a Floppy Diskette 88
For More Information 89
Configuring the Floppy Driver 90
Troubleshooting 91
Ordering Information 91
vii
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
6 Solving Problems
Common Problems and Solutions 95
Problems with Powering Up the System 95
Problems Loading and Booting the Operating System 96
Problems with the 802.3 Network 96
Problems Using a Hard Disk Drive 97
Problems Using the CD-ROM Drive 98
Problems Using the DDS Tape Drive 99
Problems Using the Floppy Disk Drive 100
Dealing with a Boot Failure 101
Running System Verification Tests 102
A Safety and Regulatory Statements
Emissions Regulations 107
Federal Communications Commission (FCC) 107
VCCI Class 2 ITE 108
108
Emissions Regulations Compliance 108
Acoustics 108
Regulation On Noise Declaration For Machines -3. GSGV 108
Electrostatic Discharge (ESD) Precautions 109
Safety Statement 110
Laser Safety Statement (U.S.A. Only) 111
Warnings and Cautions 112
viii
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
B Changing Your Workstation’s Hardware Configuration
Checking the SCSI IDs 115
Preparing Your Workstation 117
Installing Storage Devices 119
Preparing to Install Your Storage Device 120
Installing a CD-ROM or a DDS-Format Tape Drive 125
Installing a Floppy Drive 127
Installing a Hard Disk Drive in Position 1 129
Installing a Hard Disk Drive in Position 3 or Position 4 131
Replacing the Storage Tray 134
Configuring a Hard Disk Drive 136
Removing the Main Tray Assembly 139
Replacing the Main Tray Assembly 141
Installing Additional memory 143
Installing an EISA or GSC Option Board 147
Graphics Paths 148
Installing the Option Board 149
Replacing the Battery 154
Changing Your Monitor Type 155
Setting the Monitor Type from the Boot Console Interface 155
Setting the Monitor Type at Power On 155
ix
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
C SCSI Connections
SCSI Bus Differences 159
SCSI Restrictions 161
Cables 161
Connectors and Terminators 162
SCSI Configuration Constraints 162
Determining SCSI Bus Length 165
Single-Ended SCSI-2 Bus Length 165
Fast, Wide Differential SCSI Bus Length 167
Assigning SCSI Device IDs 168
Single-Ended Standard System SCSI Device IDs 170
Fast, Wide Differential SCSI IDs 172
Connecting to the SCSI Ports 173
System SCSI Port Connection 173
D The Boot Console Interface
Boot Console Interface Features 177
Accessing the Boot Console Interface 180
Booting Your Workstation 181
Searching for Bootable Media 183
Resetting Your Workstation 184
Displaying and Setting Paths 185
Displaying and Setting the Monitor Type 187
x
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
The Monitor Command 187
Displaying the Current Monitor Configuration 188
Setting the Monitor Type 189
Setting the Monitor Type at Power On 193
Displaying the Current Memory Configuration 194
Sample Output 1 195
Sample Output 2 196
Displaying the Status of the EISA Slots 197
Setting the Auto Boot and Auto Search Flags 198
Displaying and Setting the Fastboot Mode 200
Displaying the LAN Station Address 201
Displaying System Information 202
Displaying PIM Information 203
xi
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Figures
System Unit Front Panel Controls 5
System Unit Rear Panel Connectors 9
Opening the Toolbox Subpanel 30
Opening the General Toolbox 30
Opening the System_Admin Toolbox 31
Executing the SAM Icon 31
CD-ROM Drive Controls and Features 42
CD-ROM Disc Tray 45
Placing a CD-ROM Disc in a Horizontally Mounted Drive 46
Removing a CD-ROM Disc From a Horizontally Mounted Drive 47
Releasing the Disc Holder Retainers 48
Placing a CD-ROM Disc in a Vertically Mounted Drive 49
Removing a CD-ROM Disc From a Vertically Mounted Drive 50
DDS Drive Controls and Indicators 65
DDS Tape Drive LED Display Codes 67
Setting the Write-Protect Tab on a DDS Tape 70
Loading and Unloading a Data Cassette 71
Setting the Write-Protect Tab on a Floppy Diskette 81
xii
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Figures
Inserting and Removing a Floppy Diskette 82
Removing the Floor Stand 118
Disk Tray Positions 121
Mounting the Storage Device Slides 122
Mounting the Disk Shield 123
Removing the Storage Tray 124
Removing a Disk Filler Panel 125
Installing a CD-ROM or DDS Tape 126
Removing a Disk Filler Panel 127
Installing a Floppy Drive 128
Removing a Disk Filler Panel 129
Installing a Hard Disk Drive in Position 1 130
Removing the Disk Interconnect Board 131
Installing a Hard Disk Drive 132
Installing the Disk Interconnect Board 133
Installing the Storage Tray Assembly 134
Removing Main Tray Assembly 139
Replacing the Main Tray Assembly 141
xiii
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Memory Module Location 145
Installing Memory Cards 146
EISA/GSC Slots from Outside the System Unit 147
Rotating the Fan 149
Removing the EISA Retainer 149
Removing the EISA Slider and Blank Plate 150
Installing an Option Board 151
Installing the EISA Retainer and EISA Slider 152
Securing the Fan 153
Removing the Battery 154
Rear Panel SCSI Connectors without Terminators 173
xiv
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Tables
Audio Electrical Specifications 11
Serial I/O Pins 13
PS2 Keyboard and ITF Keyboard Equivalent Keys 17
Sample LANSCAN COMMAND TABLE 22
CD-ROM Drive Operating Controls and Features 43
Power Up Problems 95
Problems Loading and Booting the Operating System 96
Problems with the 802.3 Network 96
Problems Using a Hard Disk Drive 97
Problems Using the CD-ROM Drive 98
Problems Using the DDS Tape Drive 99
Problems Using the Floppy Disk Drive 100
Default SCSI IDs 120
Storage Configurations 121
C100/C110 Memory Configurations 144
SCSI Bus Differences 159
SCSI Bus Addresses, ID Numbers, and Arbitration Priorities 160
Single-Ended SCSI-2 Bus Configuration Constraints 163
xv
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Tables
Fast, Wide Differential SCSI Bus Configuration Constraints 164
Bus Length Worksheet for Single-Ended SCSI Bus 166
Fats, Wide SCSI Bus Length Worksheet for Fast, Wide Differential SCSI Bus 167
Single-Ended SCSI Device IDs 171
Fast, Wide Differential SCSI Device Drives and Device ID 172
System Paths 185
Mnemonic Style Notation 185
Graphics Configurations 192
xvi
Download from Www.Somanuals.com. All Manuals Search And Download.
1
System Overview
1
Download from Www.Somanuals.com. All Manuals Search And Download.
System Overview
This chapter introduces the HP 9000 C100/C110 workstation. Its purpose is
to familiarize you with your workstation and its controls and indicators. The
information is presented in the following sections:
•
•
•
•
•
•
•
•
•
Product Description
System unit front panel controls and LEDs
System unit rear panel connectors
Monitors
Keyboards
Pointing devices
Operating system overview
Important information you need to note
Networking overview
NOTICE:
The instructions in this chapter assume you are using HP-UX
version 9.05 or greater operating system with HP VUE version 3.0
interface.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
System Overview
Product Description
Product Description
This workstation has the following key features:
•
•
•
•
Processor Performance C100, 100 Mhz; C110, 120 Mhz
Operating System
User Interface
Compatibility
Native HP-UX (version 9.05 or greater)
HP VUE version 3.0 graphical user interface
Source and binary code compatible with the Series
700 product family
•
Optional Graphics:
Fast 2D color graphics; choice of 2 or 3 head
HCRX-8Z Fast 8-plane or 24-plane graphics
HP VISUALIZE-8\24 Accelerated 8-plane or 24-plane 3D graphics
HP VISUALIZE-48 24/24 image planes, 8 overlay planes, 24-bit Z buffer
3D graphics
•
Main Memory
32 MB to 512 MB in pairs of 16 MB or 64 MB modules.
Four pairs maximum
3
Download from Www.Somanuals.com. All Manuals Search And Download.
System Overview
Product Description
•
Internal Storage Devices:
Fast, Wide SCSI Hard Disk Drives:
1-inch Low Profile (up to three)
1.6-inch Full Height (one)
Single-Ended SCSI Removable Media:
CD-ROM Drive
or
2.0/4.0 GB, 4-mm DDS-Format Tape Drive
3.5-inch Floppy Disk Drive (not a SCSI Device)
•
•
Standard Network
Standard I/O
Ethernet IEEE 802.3 AUI
RJ45, UTP Twisted Pair
One Single-Ended, 8-bit (for removable devices)
5 MB/sec synchronous 1.5 MB/sec asynchronous
50-pin, high density SCSI connector
One Fast, Wide SCSI (for hard disk drives)
20 MB/sec synchronous 68-pin, high-density connector
Two Serial Interfaces RS232C, 9-pin male
One Parallel Interface, Centronics, BUSY handshake
25 pin female
Audio Line-in, Line-out, Mic, and Headphone
One HP-HIL connector
Two PS/2 ports
•
•
EISA/GSC
Keyboards
4 slots total; 3 EISA or GSC and 1 GSC only
PS/2 Keyboard (mouse)
or
ITF Keyboard (also known as HP HIL) (HP HIL mouse)
4
Download from Www.Somanuals.com. All Manuals Search And Download.
System Overview
System Unit Front Panel Controls and LEDs
System Unit Front Panel Controls and LEDs
Before powering on your system, you should become familiar with the
system unit controls.
Figure 1 shows the system unit front panel controls.
Removable
Storage Devices
Power Switch
Power LED
System LEDs
Mute
Volume
Headset
Mic
Figure 1
System Unit Front Panel Controls
5
Download from Www.Somanuals.com. All Manuals Search And Download.
System Overview
System Unit Front Panel Controls and LEDs
System Power Switch
Use the Power switch to power the system unit on and off.
NOTICE:
There is no need to manually shut down the HP-UX operating system on
your workstation before powering it off. When you turn off the power
switch, your workstation automatically shuts down the operating system
before terminating the power.
Power LED
The Power LED lights when the system unit power is on.
System LEDs
The system LEDs indicate the status of your workstation. In the event of a
system problem, the LEDs are lighted in different patterns to indicate error
codes. See Chapter 6 for a complete list of the system LED error codes.
LED 4 - System Heartbeat
LED 3 - SCSI Bus Activity
LED 2 - Network Transmit
LED 1 - Network Receive
6
Download from Www.Somanuals.com. All Manuals Search And Download.
System Overview
System Unit Front Panel Controls and LEDs
Audio Controls
Next to the system LEDs are the following audio controls:
Headset Jack
Volume Control
Mic Jack
Accommodates mini-headphones with a 3.5-mm diameter
miniature stereo plug.
Adjusts the audio output volume to the headset jack or line
out.
Accommodates microphones with a 3.5-mm diameter min-
iature stereo plug.
Mute Button
Turns off the audio output to line out and speaker only.
NOTICE:
The volume Control, Headphone Jack, and Microphone Jack Features of
the CD-ROM are supported through applications only
For more information on the features and electrical specifications, see
“Audio Connectors” later in this chapter.
Removable Storage Devices
The model C100/110 supports the following removable storage devices:
•
•
CD-ROM Disc Drive or DDS-Format Tape Drive
Floppy Diskette Drive
NOTICES:
Due to space limitations, a DDS-format tape drive and a CD-ROM drive
cannot both be mounted in the system at the same time.
A description of each drive’s controls and indicators is in the chapter
describing that device, later in this book.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
System Overview
System Unit Rear Panel Connectors
System Unit Rear Panel Connectors
This section describes the following connectors on the system unit’s rear
panel:
•
•
•
•
•
•
•
•
•
•
•
•
Security Loop
Audio Line IN and Line OUT connectors
PS/2 keyboard and mouse connectors
HP parallel Centronics I/O connector
802.3 AUI LAN connector
802.3 TP (Twisted Pair) LAN connector
Serial I/O connectors
HP HIL connectors (keyboard, mouse, optional HIL devices)
Monitor connector
SCSI connectors (including fast, wide SCSI and single-ended SCSI)
TOC button (Transfer of Control)
Power cord connector
NOTICE:
To maintain electro-magnetic and radio frequency emissions compliance,
verify that all cables are fully seated and properly fastened.
Figure 2 shows the locations of the connectors on the system unit’s rear
panel.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
System Overview
System Unit Rear Panel Connectors
Power
TOC
LAN-AUI
LAN-TP
Serial 1
Serial 2
PS/2 Mouse
Monitor
PS/2 Keyboard
HP Parallel
HP HIL
Single-ended SCSI
Fast, Wide SCSI
Audio Line Out
Audio Line In
Security Loop
Figure 2
System Unit Rear Panel Connectors
Security Loop
The security loop provides a means of locking the storage tray, with a pad-
lock or other locking device, to prevent unauthorized removal from the sys-
tem.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
System Overview
System Unit Rear Panel Connectors
Audio Connectors
Your workstation has audio input and output capability through external
input and output connectors on the rear panel and through an internal
speaker. The rear panel contains the Audio IN (stereo line-in) and Audio
OUT (stereo line-out) connectors.
The audio connectors are standard stereo audio mini-jacks. Hewlett-Packard
recommends using gold-plated plugs available through audio retailers for
best quality recording and playback through the external connectors. The
following is a summary of the workstation audio features:
•
Audio Features
Programmable sample rates:
8kHz, 16kHz, 32kHz, 48kHz, 11.025kHz,
22.05kHz, and 44.1kHz.
Programmable output attenuation:
0 to -96dB in -1.5dB steps
Programmable input gain:
0 to 22.5dB in 1.5dB steps
Input monitoring:
16-bit linear, 8-bit u-law, or A-law coding
Line-in
•
Audio Inputs
Mono microphone (on the front panel) compatible with 1.5V
phantom supply (bias voltage supplied by the system).
CD-ROM audio (if internal CD-ROM is installed.
Line-out
•
•
Audio Outputs
Audio CODEC
Headphone (on the front panel)
Built-in mono speaker
Crystal CS4215
10
Download from Www.Somanuals.com. All Manuals Search And Download.
System Overview
System Unit Rear Panel Connectors
The audio electrical specification for this workstation are summarized in
Table 1.
Table 1
Audio Electrical Specifications
Frequency Response
Input Sensitivity/Impedance
Line In
25-20,000 Hz
2.0Vpk/47k ohm
22mVpk/1k ohm
Microphone
Max Output Level/Impedance
Line Out
2.8Vpp/47k ohm
2.75Vpp/50 ohm
5.88Vpp/48 ohm
Headphone
Speaker (internal)
Output Impedance
Line Out
619 ohm
118 ohm
Headphone
Signal to Noise*
Line Out
65 dB
61 dB
63 dB
61 dB
57 dB
Headphone
Speaker
Line In
Microphone
THD (w nominal load)
Line Out
-73 dB
-70 dB
-68 dB
-75 dB
-73 dB
Headphone
Speaker
Line In
Microphone
*To convert from dB to number of significant bits, use the formula:
dB
[20log10]
dB
6
-------------------------- ------
'n=
≈
For example, for 61dB S/N then n=61/6 or approx. 10 significant bits, or in other
words, about 6 bits of noise.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
System Overview
System Unit Rear Panel Connectors
Keyboard Connectors
PS/2 Keyboard and Mouse Connectors
The PS/2 connectors provide an interface for a keyboard and a mouse to the
system. Consult the documentation that accompanies each input device for
specific information concerning its use.
HP-HIL Keyboard Connector
The HP HIL connector provides an interface for the ITF Keyboard and its
mouse to the system. Consult the documentation that accompanies each
input device for specific information concerning its use.
HP Parallel I/O Connector
The 25-pin HP Parallel I/O interface uses Centronics interface protocols to
support peripheral devices such as printers and plotters. Consult the docu-
mentation that accompanies each peripheral device for specific information
concerning its use.
802.3 Network Connectors
Your workstation has built-in ThickNet LAN-AUI and LAN-TP (Twisted
Pair) connectors for the 802.3 (ETHERNET) network. Connections to Thin-
LAN networks require an external transceiver. Your workstation will autose-
lect the correct network setting.
Serial I/O Connectors
You can attach a variety of pointing devices (such as a mouse or trackball),
or peripheral devices to the Serial Input/Output (SIO) ports on the C100/
C110 workstation. Peripheral devices include printers, plotters, modems,
and scanners. Consult the documentation that accompanies each pointing or
peripheral device for specific information concerning its use.
The SIO ports are programmable. You can set functions such as bit rate,
character length, parity, and stop bits. The SIO Ports are used as an interface
for serial asynchronous devices to the CPU. The ports operate at up to a
460.8K baud rate.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
System Overview
System Unit Rear Panel Connectors
Table 2 shows the SIO connector pin listings. The serial connectors are 9-pin
D-sub connectors. Signal names are those specified in the EIA RS-232 stan-
dard.
Table 2
Serial I/O Pins
Pin No.
Signal
Description
1
2
3
4
5
6
7
8
9
DCD
RXD
TXD
DTR
GND
DSR
RTS
CTS
RI
Data Carrier Detect
Receive Data
Transmit Data
Data Terminal Ready
Ground
Data Set Ready
Request To Send
Clear To Send
Ring Indicator
SCSI Connectors
Use the single-ended and fast, wide connectors to connect external SCSI
devices such as DDS-format tape drives and CD-ROM drives. Consult the
documentation that accompanies each SCSI device for specific information
concerning its use. Refer to Appendix C for information about connecting
SCSI devices to your workstation.
NOTICE:
When attaching external SCSI devices, be sure to terminate the last device
on the external SCSI bus.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
System Overview
System Unit Rear Panel Connectors
TOC Button
The TOC button resets the system and transfers control from the default
device to an auxiliary device.
Power Cord Connector
Plug the workstation’s power cord into the power cord connector to provide
ac power to the system.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
System Overview
Monitors
Monitors
You can use one of two HP monitors with your workstation:
•
•
17-inch, 1280x1024 color monitor (A4032A)
20-inch, 1280x1024 color monitor (A4033A)
Before using your monitor you should become familiar with its controls,
connectors, and indicators. For this information, consult the documentation
that was packaged with your monitor, or see the HP A4032/A4033 Color
Monitor CE Handbook (A4033-90099).
15
Download from Www.Somanuals.com. All Manuals Search And Download.
System Overview
Keyboards
Keyboards
There are two types of Hewlett-Packard keyboards available for use with
your workstation.
•
•
PS/2 Keyboard (P/S2 interface)
ITF Keyboard (HP-HIL interface)
CAUTION:
Only connect devices that conform to the HP-HIL specification with
Hewlett-Packard HIL ports. Devices that are not HP-HIL compatible but
have similar connectors may appear to be compatible, but will damage
your system.
Keyboard Differences
Aside from the obvious difference in the appearance of the PS/2 and ITF
keyboards due to the arrangement of the keys, there is also a difference in
the keys and their output codes. For example, some keys on one keyboard
may not exist on the other keyboard. These keys generate codes that may not
exist as output from the other keyboard (or may be generated by a different
key). Codes that are generated when a key is pressed are called keycodes.
Some applications expect to use keycodes generated by keys existing on one
of the keyboards (the ITF keyboard for example). Since the keys do not exist
on the other keyboard (the PS/2 keyboard for example), an accommodation
must be made if the PS/2 keyboard is to be used. In most cases, it is still pos-
sible to use some other key that is equivalent (generates the same keycode
from a different keycap). To do this, it is necessary to know which keys are
equivalent on the two keyboards. Table 3 compares the equivalent keys of
the ITF and PS/2 keyboards.
NOTICE:
Keyboard keys not mentioned inTable 3 are the same on both keyboards.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
System Overview
Keyboards
Table 3
PS2 Keyboard and ITF Keyboard Equivalent Keys
PS/2 Keycap Symbol ITF Keycap Symbol
F9
blank1 (left)
blank2
F10
F11
blank3
F12
blank4 (right)
Menu
PrintScreen / SysReq
Scroll Lock
Pause / Break
Page Up
Stop
Break / Reset
Prev
Num Lock
End
System / User
Select
Page Down
Enter
Next
Return
Alt (left)
Extend Char (left)
Extend Char (right)
Clear Line
Clear Display
Insert Line
Delete Line
Print / Enter
, (number pad)
Tab (number pad)
Esc / Del
Alt (right)
No Equivalent
No Equivalent
No Equivalent
No Equivalent
No Equivalent
No Equivalent
No Equivalent
Esc
Insert
Insert Char
17
Download from Www.Somanuals.com. All Manuals Search And Download.
System Overview
Keyboards
Table 3
PS2 Keyboard and ITF Keyboard Equivalent Keys
PS/2 Keycap Symbol ITF Keycap Symbol
Home
Delete
Delete Char
Caps
Caps Lock
Esc Shifted
Esc / Del Shifted
Pause / Break Shifted Break / Reset Shifted
Num Lock Shifted
0 / Ins (number pad)
1 / End (number pad)
System / User Shifted
0 (number pad)
1 (number pad)
2 (number pad)
2 /
(number pad)
3 / Pg Dn
3 (number pad)
(number pad)
4 (number pad)
6 (number pad)
7 (number pad)
4 /
6 /
(number pad)
(number pad)
7 / Home
(number pad)
8 /
(number pad)
8 (number pad)
9 (number pad)
9 / Pg Up
(number pad)
. / Del (number pad)
Ctrl (left)
. (number pad)
Ctrl
Ctrl (right)
No Equivalent
18
Download from Www.Somanuals.com. All Manuals Search And Download.
System Overview
Pointing Devices
Pointing Devices
You can use an HP three-button mouse, a trackball, or other options as point-
ing devices using the PS/2 connector, the HIL port, or the Serial ports. For
instructions on using your particular pointing device, see the manual that
came with it.
For general information on using three-button mice and on the various cur-
sor shapes associated with different areas of HP VUE while using a mouse,
see Using Your HP Workstation.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
System Overview
Operating System Overview
Operating System Overview
Your workstation uses the HP-UX operating system, version 9.05 or greater.
Instant Ignition systems, (systems with preloaded software), have X-win-
dows and Hewlett-Packard’s graphical user interface, HP VUE version 3.0,
installed and configured.
Please refer to the “Instant Ignition System Configuration Information”
sheet that shipped with your system for details on configuration.
If you have any questions about Instant Ignition, refer to Using Your HP
Workstation for more information.
NOTICE:
When you power on your workstation, a selftest program runs before the
system boots.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
System Overview
Important Information You Need to Note
Important Information You Need to Note
Before you begin using your workstation, take a moment to gather the fol-
lowing important information and note it in the appropriate subsection for
future use:
•
•
•
•
•
LANIC ID
SCSI device ID
Device file used for each SCSI device
Internet Protocol (IP) address
Subnetwork mask
NOTICE:
For help with these, refer to Using your HP Workstation.
LANIC ID
Locate the contents label that comes with the workstation shipping carton.
Find the LANIC ID listed there and write it down in the space provided:
LANIC ID ____________________________________________
You can also get your LANIC ID by using the lanscan command in a termi-
nal window. To do this, follow these steps:
1
2
Turn your workstation and monitor on, if you have not already done so. Figure 1
of this chapter shows the location of the power switch on the workstation. See the
documentation that came with your monitor for the location of the monitor power
switch.
Move the mouse cursor to the Terminal Control on the Front Panel of your Work-
space and click the left mouse button.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
System Overview
Important Information You Need to Note
Terminal Control
A terminal window opens.
3
4
Move the mouse cursor into the terminal window and single-click the left mouse
button.
If you are using HP-UX 9.05, enter the following at the prompt:
/etc/lanscan
If you are using HP-UX 10.0, enter the following at the prompt:
/usr/sbin/lanscan
You will see a table similar to Table 4.
Table 4
Sample LANSCAN COMMAND TABLE
Hardware Station
Dev Hard Net-Interface
ware
NetMgt Encapsulation
Path
Address
lu
State NameUnit State ID
UP lan0 UP
Methods
2.0.2
0x0800091595EE 0
4
ETHER IEEE8023
The LANIC ID in this example is 0800091595EE.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
System Overview
Important Information You Need to Note
SCSI ID and Device File Information for HP-UX 9.05
Default device file names for your drives are listed below. The underlined
number in the device file name indicates the SCSI ID number:
Device
Device File Name
/dev/dsk/c201d2s0
/dev/rmt/3m
CD-ROM drive
DDS-format tape drive
These device file names assume the SCSI ID of your drive is set to the fac-
tory default. If you change the factory-set value, you must create a new
device file and substitute the pathname of your device file for the pathname
above. See the System Administration Tasks manual for information on how
to create a device file.
SCSI ID and Device File Information for HP-UX 10.0
Default device file names for your drives are listed below.
Device
Device File Name
CD-ROM drive
/dev/[r]dsk/c#t#d#
c# identifies the bus address of the SCSI interface card.
t# identifies the target address of the SCSI disk.
d# identifies the SCSI lun address (0, except for disk arrays).
The device file should have its protections set to read and write for owner
and group.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
System Overview
Important Information You Need to Note
Device file names for DDS drives at HP-UX 10.0 depend on the naming
conventions of the system on which you are installing them.
For installation on a system permitting long file names:
/dev/rmt/c#t#d#BEST
/dev/rmt/c#t#d#BESTb
/dev/rmt/c#t#d#BESTn
/dev/rmt/c#t#d#BESTnb
AT&T style, best available density,
character entry.
Berkeley style, best available density
character entry.
AT&T style, no rewind, best available
density, character entry.
Berkeley style, no rewind, best available
density, character entry.
For installation on a system requiring short file names:
/dev/rmt/c#t#d#f0
/dev/rmt/c#t#d#f0b
/dev/rmt/c#t#d#f0n
/dev/rmt/c#t#d##f0nb
AT&T style, best available density,
character entry.
Berkeley style, best available density
character entry.
AT&T style, no rewind, best available density
character entry.
Berkeley style, no rewind, best available
density, character entry.
IP Address and Subnetwork Mask Information
Get the IP address and the subnet mask information for your workstation
from either your System Administrator or your Network Administrator and
note them here:
IP address ____________________________________________________
subnet mask __________________________________________________
24
Download from Www.Somanuals.com. All Manuals Search And Download.
System Overview
Networking Overview
Networking Overview
Your workstation is capable of many more tasks than are described in this
owner’s guide. This section gives an overview of some of the networking
capabilities of your system and directs you to the appropriate source for
more information.
Mail
Electronic mail allows you to send and receive mail messages on your work-
station. For information on setting up and using electronic mail on your
workstation, contact your system administrator and also see the Using Your
HP Workstation manual that came with your workstation.
telnet
The telnet application uses the TELNET protocol to communicate with
another computer system on the network. The telnet application allows you
to log on to the remote system from your workstation. If your system has
manpages installed, you may read the online telnet man page by entering the
following at a command-line prompt:
man telnet
25
Download from Www.Somanuals.com. All Manuals Search And Download.
System Overview
Networking Overview
rlogin
The rlogin application also allows you to log on to another computer system
on the network from your workstation. For more information on rlogin, see
the Using Your HP Workstation manual that came with your workstation and
read the online man page by entering the following at a command-line
prompt:
man rlogin
ftp
The ftp application is a user interface to the File Transfer Protocol. Use ftp to
copy files between your workstation and another computer system on the
network. For more information, see the Using Your HP Workstation manual
that came with your workstation and read the online man page by entering
the following at a command-line prompt:
man ftp
rcp
The rcp application allows you to remotely copy files from another computer
system on a network to your workstation. For more information, see the
Using Your HP Workstation manual that came with your workstation and
read the online man page by entering the following at a command-line
prompt:
man rcp
NFS
The Network File System (NFS) allows your workstation to access files on
remote computer systems as if they were on your local system. The file sys-
tem on the remote computer system does not have to be compatible with
your workstation’s file system. For more information, see Installing and
Administering NFS Servers and HP-UX System Administration Tasks manu-
als.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Setting Up Your Printer
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Up Your Printer
This chapter describes how to configure your workstation to use a printer
that you have physically attached to either the parallel connector or the serial
(RS-232C) connector on the rear of your workstation.
This chapter is divided into the following sections:
•
•
•
•
•
Gathering printer information
Setting up a local printer using SAM
Setting up your printer for network printing
Printing a file
Solving printing problems
The instructions in this chapter assume you are using HP-UX version 9.05 or
10.0 operating system with HP VUE version 3.0 or later interface.
NOTICES:
Make sure you have installed the printer as described in the manufacturer’s instruc-
tions before following the instructions in this chapter. Also ensure that the printer is
powered on, connected to your workstation, has paper loaded, and is online.
Some procedures in this chapter require you to log in as root. If you cannot
log in as root, contact your system administrator.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Up Your Printer
Gathering Printer Information
Gathering Printer Information
Before you start, fill in the following list with the requested information and
refer to it during the printer setup procedure:
•
Printer Interface (check one):
❒ Parallel
❒ Serial (RS232C) Port 1
❒ Serial (RS232C) Port 2
•
•
Printer Name ____________________________________________________
(The printer name is a name the system uses to identify the printer. The printer
name can be any name that you wish.)
Printer Model Number_____________________________________________
(On Hewlett-Packard printers the model number is located on a label on the back
of the printer.)
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Up Your Printer
Setting Up a Local Printer Using SAM
Setting Up a Local Printer Using SAM
Follow the instructions in this section to set up a printer that is physically
attached to your workstation.
The procedures in this section require you to log in as root. If you cannot log
in as root, contact your system administrator.
If your workstation is running HP VUE, follow these instructions to set up
your printer using SAM.
1
Log in as root. If you need information on logging in or setting up a user account,
see Using Your HP Workstation.
2
Move the mouse pointer to the up arrow above the Toolbox control and click the
left mouse button. (This is called a single click, or simply a click.)
Figure 3
Opening the Toolbox Subpanel
3
The Toolbox subpanel opens. Click on the General toolbox icon, shown below.
Figure 4
Opening the General Toolbox
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Up Your Printer
Setting Up a Local Printer Using SAM
4
A file manager window appears with a number of icons in it. Double-click on the
System_Admin toolbox icon.
Figure 5
Opening the System_Admin Toolbox
5
Move the mouse cursor to the SAM icon shown below (your icon can look like
either of these) and double-click the left mouse button.
Figure 6
Executing the SAM Icon
6
The System Administration Manager window opens. Double-click on Printers
and Plotters ->.
7
The Printers and Plotters window opens. Double-click on Printers/Plotters.
If your workstation doesn’t have any printers set up, a message window opens.
Click on OK to remove it.
8
9
From the Actions menu, click on Add Local Printer/Plotter.
Another menu opens. If your printer is connected to the parallel port on your
workstation, click on Add a Parallel Printer/Plotter.
If your printer is connected to one of the serial connectors on your workstation,
click on Add Serial (RS-232C) Printer/Plotter.
A window opens displaying the available parallel or serial interfaces.
10 If you chose Add Parallel Printer/Plotter in the previous step, only one parallel
interface will be listed. Place the mouse cursor on the listed parallel interface and
click the left mouse button.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Up Your Printer
Setting Up a Local Printer Using SAM
If you chose Add Serial (RS-232C) Printer/Plotter in the previous step, more
than one serial interface may be listed. The serial interfaces are listed in ascend-
ing order. The lowest numbered serial interface corresponds to the lowest num-
bered serial connector on your workstation. Choose the serial interface that
corresponds to the connector to which you have connected your printer. Place
the mouse cursor on the selected serial interface and click the left mouse button.
11 Click on OK.
12 A window opens. Click on the Printer Name box. Then enter the printer’s name
and press Enter.
13 Click on Printer/Model Interface.
14 A window opens. Move the mouse cursor onto the scroll bar slider at the side of
the new window. Press and hold the left mouse button while moving the mouse.
When the model name of your printer appears, release the left mouse button.
15 Move the mouse cursor to your printer’s model name and click the left mouse
button.
16 Click on OK.
The window closes and the Add Local Printer/Plotter window becomes visible
again.
17 If you want your printer to be set as the system default printer, move the mouse
cursor to the small box labeled Make this the system default printer and click
the left mouse button.
18 Click on OK.
19 A small window opens with a message that asks if you want to add your printer
to the “Printers” subpanel. Click on Yes.
20 Another small window opens with a message that asks if you want to restart the
workspace manager. With the left mouse button, click on OK.
21 If the print spooler was not previously running, a window will open with the fol-
lowing question:
Do you want to start the print spooler now?
Click on Yes.
22 A window appears asking if your printer is powered on, has paper, is connected
to your workstation, and is online. Check your printer to make sure it meets these
requirements.
Click on OK.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Up Your Printer
Setting Up a Local Printer Using SAM
23 Click on OK at the bottom of the Messages window.
The Printer/Plotter Manager window now lists your printer.
24 Move the cursor to the word List at the top of the Printer/Plotter Manager win-
dow and click the left mouse button.
25 A menu opens below the word List. Click on Exit.
The main SAM window becomes visible again.
26 In the main SAM window, click on Exit SAM.
The SAM window closes.
27 Double-click on the window menu button in the upper-left corner of the Toolbox
window. The window closes.
28 To test the printer, first create a terminal window by clicking the Terminal Con-
trol on the Front Panel as shown. Refer to Using Your HP Workstation for the
placement if the Terminal Control if you are using VUE Lite.
Terminal Control
A terminal window opens.
29 Move the mouse cursor into the terminal window and click the left mouse button.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Up Your Printer
Setting Up a Local Printer Using SAM
30 If you made your printer the default system printer, enter the following command
to test your printer:
lp .vueprofile
If your printer isn’t the default system printer, enter the following command to
test your printer:
lp -dprintername .vueprofile
where printername is the name you chose when setting up your printer.
The lp command sends files to a printer.
The file named .vueprofile prints out on the printer.
If the file doesn’t print, see the section titled “Printing Problems,” later in this
chapter.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Up Your Printer
Setting Up Your Printer for Network Printing
Setting Up Your Printer for Network Printing
If you have a printer physically attached to your workstation, you can set it
up to receive print requests from other computers on your network. To do
this, you must start up the remote line printer daemon.
Follow the instructions in this section to set up your workstation to accept
print requests from other computers on your network.
1
Log in as root. If you need information on logging in or setting up a user account,
see Using Your HP Workstation.
2
If you are using HP-UX 9.05, using a text editor such as vi or Text Editor, edit
the following file:
/etc/inetd.conf
If you are using HP-UX 10.0, using a text editor such as vi or Text Editor, edit
the following file:
/usr/sbin/inetd.conf
3
Find the following section in the file:
##
#
# Other HP-UX network services
#
##
4
The following line should be directly below Other HP-UX network services:
# printer stream tcp nowait root /usr/lib/rlpdaemon rlpdaemon -i
If the line is present, delete the pound sign (#) from the beginning. If the line is
not there, add it without the pound sign (#) at the beginning.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Up Your Printer
Setting Up Your Printer for Network Printing
The line should look like the following:
printer stream tcp nowait root /usr/lib/rlpdaemon rlpdaemon -i
5
6
Save the file and close it.
Click on the Terminal Control on the Front Panel of your Workspace.
A terminal window opens.
7
8
Move the mouse cursor into the terminal window and click the left mouse button.
If you are using HP-UX 9.05, enter the following command line to reboot your
workstation:
/etc/reboot
If you are using HP-UX 10.0, enter the following command line to reboot your
workstation:
/usr/sbin/reboot
Your workstation shuts itself down and then reboots automatically. This may
take a few minutes. When the login prompt returns, your system is ready to
accept printer requests from other computers on your network.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Up Your Printer
Printing a File
Printing a File
To print a file, use one of the following command lines in a terminal window
lp filename
or
lp -dprintername filename
where filename is the name of the file that you want to print, and
printername is the name of the printer on which you wish to print the file.
The lp command sends files to a printer.
1
Click on the Terminal Control on the Front Panel of your Workspace.
A terminal window opens.
2
3
Move the mouse cursor into the terminal window and click the left mouse button.
Enter the lp command as described above.
For more information on the lp command, enter the following:
man lp
Also see the manual Using Your HP Workstation for information on printing
files by dragging and dropping the file icon onto the printer tool.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Up Your Printer
Solving Printer Problems
Solving Printer Problems
If you have problems printing, check the following:
•
•
•
•
•
•
•
Printer’s power cord is plugged in.
Printer is powered on.
Printer is online.
Printer has paper loaded.
Printer is set up for the correct interface type.
Printer cable is connected to the correct interface port on your printer.
Printer cable is connected to the correct interface port on your workstation.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Using Your CD-ROM Drive
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your CD-ROM Drive
This chapter describes how to use your CD-ROM drive. It is divided into the
following sections:
•
•
•
•
CD-ROM drive and CD-ROM media descriptions
Operating the CD-ROM Drive
Mounting and unmounting a CD-ROM disc
Troubleshooting
NOTICE
Be sure you read and understand the information on mounting and
unmounting CD-ROM discs before you begin using your CD-ROM disc
drive.
This chapter provides an overview of the optional CD-ROM drive and
media, and describes how to use the CD-ROM drive. We assume the CD-
ROM drive is set to the factory default address of SCSI ID 2.
The instructions in this chapter assume you are using HP-UX version 9.05 or
later operating system with HP VUE version 3.0 or later interface.
NOTICE
Some procedures in this chapter require you to log in as root. If you cannot
log in as root, contact your system administrator.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your CD-ROM Drive
CD-ROM Drive and CD-ROM Media Descriptions
CD-ROM Drive and CD-ROM Media Descriptions
This section describes basic information needed for using the CD-ROM
drive and CD-ROM discs.
CD-ROM Drive
The CD-ROM drive is a random access read-only mass storage device that
uses removable CD-ROM discs. The drive supports the ISO 9660 and High
Sierra format standards. You can access information from the drive like any
other disk drive, except that you cannot write to the drive. The drive contains
a semiconductor laser for reading data optically, and includes an embedded
controller with a SCSI interface.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your CD-ROM Drive
CD-ROM Drive and CD-ROM Media Descriptions
Controls and Features
Figure 7 shows and Table 5 describes the operating controls and features of
the CD-ROM drives.
Emergency
Busy
Indicator
Eject Hole
Headset
Jack
Volume
Control
Eject
Button
Thumbwheel
Figure 7
CD-ROM Drive Controls and Features
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your CD-ROM Drive
CD-ROM Drive and CD-ROM Media Descriptions
Table 5
CD-ROM Drive Operating Controls and Features
Control/Feature
Purpose
Headset Jack
You can plug mini-headphones with a 3.5-mm diameter
miniature stereo plug into this jack.
Volume Control
Busy Indicator
Use the volume control to adjust the audio output volume to
the headset jack.
The Busy Indicator lights during a data access operation and
blinks during a data transfer. The indicator blinks initially
and then stays lit when there is one of the following:
•
•
•
A defective disc
A disc insertion error (for example, an upside-down disc)
No disc present
Eject Button
Press the Eject Button to open the Disc Tray and insert or
remove a disc. When the drive is in use, you must press the
eject button for more than one second to open the Disc Tray.
Emergency Eject
By removing the Phillips type screw and inserting the end of
a paper clip, you can open the Disc Tray when the
workstation does not have power.
NOTICE
The Volume Control, Headset Jack, and Audio Jack features of the CD-
ROM drive are supported through applications only.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your CD-ROM Drive
CD-ROM Drive and CD-ROM Media Descriptions
CD-ROM Media
CD-ROM discs are 120 mm (4.7 in.) in diameter, and use one data surface
with a capacity of approximately 600 megabytes. The data surface contains
pits and flat spots arranged in a continuous spiral track, which is read at a
constant speed. You may access files and data stored on a CD-ROM disc, but
you may not write files or data to a CD-ROM disc.
CD-ROM data discs are identical to audio compact discs (CDs) except that
they store computer data and information.
CAUTION:
Handle CD-ROM discs by the edges only. Always be sure a CD-ROM disc is either
in the CD-ROM drive or its protective case when not in use. This will lessen the
chance of exposing the disc surface to dust. Over time, dust reduces the reliability of
the read head in the CD-ROM drive.
Caring for CD-ROM Discs
Observe the following guidelines to help prevent data loss and prolong the
life of your CD-ROM discs and drive:
•
•
•
Use CD-ROM discs in a clean environment to prevent dust particles from
scratching disc surfaces.
Store CD-ROM discs in a cool, dry place to prevent moisture and heat
damage.
Don’t try to clean the surface of a CD-ROM disc with cleaning solvents,
as some cleaning solvents may damage the disc.
NOTICE:
You must mount the disc after loading it into the drive. Refer to the section
“Mounting and Unmounting a CD-ROM Disc,” later in this chapter, for
instructions about mounting a disc.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your CD-ROM Drive
Operating the CD-ROM Drive
Operating the CD-ROM Drive
This section describes how to perform tasks with your CD-ROM drive.
Loading and Unloading a CD-ROM in the Disc Tray
This subsection describes how to load or unload a CD-ROM disc in the CD-
ROM drive.
Disc Tray Description
This CD-ROM is designed to be used in either the horizontal or vertical
position, depending on whether your system unit is horizontal or vertical (in
the floor stand). The disc tray has three spring-loaded disc holders that hold
the disc in place when the CD-ROM drive is in the vertical position. When
the drive is in the horizontal position, the disc holders are not used and are
held out of the way by three disc holder retainers. Figure 8 shows the CD-
ROM disc tray, and disc holders.
Disc
Holder
Disc
Holder
Disc
Holder
Figure 8
CD-ROM Disc Tray
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your CD-ROM Drive
Operating the CD-ROM Drive
Loading a CD-ROM Disc in a Horizontally Mounted Drive
This CD-ROM drive has an automatic loading/ejecting feature. To load a
disc in the CD-ROM drive, follow these steps:
Figure 9
Placing a CD-ROM Disc in a Horizontally Mounted Drive
1
2
Check that the workstation is powered on.
To open the disc tray, press and release the load/eject button on the CD-ROM
drive.
3
4
Be sure the disc holders are held away from the disc by the disc holder retainers.
Hold the disc by the edges with the label side up and place it in the disc tray as
shown in Figure 8.
5
To close the disc tray, push the front of the disc tray gently towards the drive until
it closes by itself.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your CD-ROM Drive
Operating the CD-ROM Drive
Unloading a CD-ROM Disc in a Horizontally Mounted Drive
Perform the following steps to unload a disc from the CD-ROM drive:
Figure 10
Removing a CD-ROM Disc From a Horizontally Mounted Drive
1
Press the eject button to eject the disc tray from the drive. If the drive is in use,
you must press the eject button form more than one second to eject the disc tray.
The emergency eject feature allows you to eject the disc tray if the normal proce-
dure fails. See Table 5.
NOTICE:
You must unmount the disc before eject it from the drive. Refer to the
subsection, “Unmounting a CD-ROM Disc Using SAM,” for instruction on
unmounting a disc.
2
3
Wait until the drive has fully ejected the disc tray, then remove the disc from the
tray as shown in Figure 11. Be careful to touch only the edges of the disc.
To close the Disc Tray, push the front of the disc tray gently towards the drive
until it closes by itself.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your CD-ROM Drive
Operating the CD-ROM Drive
Loading a CD-ROM Disc in a Vertically Mounted Drive
To load a disc in the CD-ROM drive, follow these steps:
Disc
Holder C
Disc
Holder A
Disc
Holder B
Figure 11
Releasing the Disc Holder Retainers
1
Make sure the three disc holders are disengaged from the disc holder retainers, as
shown in Figure 11.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your CD-ROM Drive
Operating the CD-ROM Drive
2
Hold the disc with the label side to the left and place the edge of the disc onto disc
holders A and B as shown in
Figure 12
Placing a CD-ROM Disc in a Vertically Mounted Drive
3
Press down gently against the spring tension of disc holders A and B, and swing
the top of the disc in until it is held by disc holder C.
4
To close the disc tray, push the front of the disc tray gently towards the drive until
it closes by itself.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your CD-ROM Drive
Operating the CD-ROM Drive
Unloading a CD-ROM Disc in a Vertically Mounted Drive
Perform the following steps to unload a disc from the CD-ROM drive:
Figure 13
Removing a CD-ROM Disc From a Vertically Mounted Drive
1
Press the eject button to eject the disc tray from the drive. If the drive is in use,
you must press the eject button for more than one second to eject the disc tray.
The emergency eject feature allows you to eject the disc tray if the normal proce-
dure fails. See Table 5.
NOTICE:
You must unmount the disc before eject it from the drive. Refer to the
subsection, “Unmounting a CD-ROM Disc Using SAM,” for instruction on
unmounting a disc.
2
Press down gently against the spring tension of disc holders A and B and swing
the top of the disc away from disc holder C as shown in Figure 13.
3
4
Remove the disc from disc holders A and B.
To close the Disc Tray, push the front of the disc tray gently towards the drive
until it closes by itself.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your CD-ROM Drive
Operating the CD-ROM Drive
Verifying the CD-ROM Drive Operation
To verify that your workstation can communicate with the CD-ROM drive,
follow these steps:
1 Click on the Terminal Control on the Front Panel of your Workspace.
Terminal Control
A terminal window opens.
2 Move the mouse cursor into the terminal window and click the left mouse
button.
3 If you are using HP-UX 9.05, enter the following at the prompt:
/etc/ioscan -d scsi
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your CD-ROM Drive
Operating the CD-ROM Drive
After a few moments the ioscan utility lists all of the SCSI I/O devices it could
find. If there is a SCSI CD-ROM drive in the list, that listing appears similar to
the following:
H/W Path
Description
Status
=======================================
2.0.1.2.0 cd-rom_drive ok(nnnnnnnn)
If you are using HP-UX 10.0, enter the following at the prompt:
/usr/sbin/ioscan -d sdisk
After a few moments the ioscan utility lists all of the SCSI I/O devices it could
find. The list appears similar to the following:
H/W Path
Class
Description
============================================
bc
8
bc
ext_bus
I/O Adapter
8/12
GSC built-in Fast/Wide SCSI Interface
8/12.0
8/12.0.0
8/12.5
8/12.5.0
8/12.6
8/12.6.0
8/16
target
disk
QUANTUM LPS1080WD
target
disk
DEC
DSP3210SW
target
disk
DEC
DSP3210SW
ba
Core I/O Adapter
Built-in SCSI
8/16/5
8/16/5.2
ext_bus
target
8/16/5.2.0 disk
TOSHIBA CD-ROM XM-4101TA
SEAGATE ST3600N
8/16/5.4
target
8/16/5.4.0 disk
8/16/5.6
target
8/16/5.6.0 disk
MICROP 2112
10
bc
I/O Adapter
10/12
10/12.4
ext_bus
target
GSC add-on Fast/Wide SCSI Interface
10/12.4.0 disk
SEAGATE ST31200W
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your CD-ROM Drive
Operating the CD-ROM Drive
If ioscan does not see your CD-ROM drive it returns the following message:
ioscan: No hardware found
If you receive this message, go to Chapter 6, “Solving Problems.”
Using Device Files
Device files are special files that tell your system which pathway to use
through the system hardware when communicating with a specific device,
and tell what kind of device it is.
The examples in this section assume that the SCSI ID of your CD-ROM
drive is set to the factory default of SCSI ID 2, using the device file
/dev/dsk/c201d2s0. (The underlined 2 indicates the SCSI ID number.)
NOTICE:
The device file name used in these examples is appropriate only for
systems running HP-UX 9.05. If you are using HP-UX 10.0, the device file
names will depend on the naming conventions of your particular system.
See “SCSI ID and Device File Information for HP-UX 10.0” in Chapter 1
of this book.
If you set the SCSI address of your CD-ROM drive to a value other than 2,
you must create a device file for it, then substitute the pathname of your
device file in the examples that follow. Refer to the System Administration
Tasks manual for information on how to create a device file.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your CD-ROM Drive
Mounting and Unmounting a CD-ROM Disc
Mounting and Unmounting a CD-ROM Disc
To access information on a CD-ROM disc, you must first mount the disc.
This applies to file system information only. If you wish to load a music CD,
for example, you would not need to mount the disc. Mounting a disc with
file system information on it gives the disc a pathname that allows your
workstation to communicate electronically with it. You must unmount the
CD-ROM disc before removing it from the drive.
CAUTION:
To use a CD-ROM disc as a mounted file system, you must mount the CD-ROM disc
every time you load it into the drive. You must also unmount the CD-ROM disc
every time you unload it from the drive. Failure to mount or unmount a disc can cause
a system error condition that can require rebooting the system.
If your workstation is running HP VUE, follow these instructions to mount
and unmount a CD-ROM disc as a file system. If you’re using something
other than HP VUE, use the instructions for mounting and unmounting a
CD-ROM disc that come with that product. For more information on config-
uring your CD-ROM drive, see the System Administration Tasks manual or
online help.
The procedures in this chapter require you to log in as root. If you cannot
log in as root, contact your system administrator.
Mounting a CD-ROM Disc Using SAM
Use the following procedure to mount a CD-ROM disc:
1 Log in as root. If you need information on logging in or setting up a user
account, see Using Your HP Workstation.
2 Load the CD-ROM disc into the disc tray and gently push the tray into the
drive.
3 Move the mouse pointer to the arrow above the Toolbox control and click
the left mouse button once.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your CD-ROM Drive
Mounting and Unmounting a CD-ROM Disc
Toolbox Arrow
4 The Toolboxes subpanel opens. Click on the General toolbox icon,
shown below.
5 A file manager window appears with a number of icons in it. Double-click
on the System_Admin toolbox icon.
6 Move the mouse cursor to the SAM icon shown below (your icon can look
like either of these) and double-click the left mouse button.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your CD-ROM Drive
Mounting and Unmounting a CD-ROM Disc
7 The System Administration Manager window opens. Double-click on
Peripheral Devices ->.
8 The Peripheral Devices window opens. Double-click on Disks and File
Systems ->.
9 The Disks and File Systems window opens. Double-click on CD-ROM,
Floppy, and Hard Disks.
The following screen message appears:
Scanning the system’s hardware...
The CD-ROM, Floppy, and Hard Disks window opens containing a list of
drives currently configured on this system. Disks that are unmounted will have
the word “unused” in the Use column.
10 From the Actions menu, click on Add a Hard Disk Drive
11 The Select a Disk to Add... window opens with a list of unused disks. Highlight
the CD-ROM disc you want to mount.
12 Click on OK.
13 The Set Disk Usage and Options... window opens. Select File System
and click on OK.
14 The following screen messages appear:
Task started.
Creating the device file...
Mounting file system...
Modifying “/etc/checklist”...
Task completed.
Click on OK.
Now you can access the CD-ROM disc as you would any other mounted file
system.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your CD-ROM Drive
Mounting and Unmounting a CD-ROM Disc
Unmounting a CD-ROM Disc Using SAM
Use the following procedure to unmount a CD-ROM disc:
NOTICE:
Before you unmount a CD-ROM disc, make sure that your working
directory (the directory in which a relative path name search begins)
is set to some directory other than the one under which the disc was
mounted.
CAUTION:
If you wish to use a CD-ROM disc as a mounted file system, you must mount
the CD-ROM disc every time you load it into the drive. You must also
unmount the CD-ROM disc every time you unload it from the drive. Failure
to mount or unmount a disc may cause a system error condition that may
require rebooting the system.
1 Log in as root. If you need information on logging in or setting up a user
account, see Using Your HP Workstation.
2 Move the mouse pointer to the Toolbox control and click on the arrow
with the left mouse button.
Toolbox Arrow
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your CD-ROM Drive
Mounting and Unmounting a CD-ROM Disc
3 The Toolbox subpanel opens. Place the mouse cursor on the General
toolbox icon, shown below, and click the left mouse button.
4 A file manager window appears with a number of icons in it. Double-click
on the System_Admin toolbox icon.
5 Move the mouse cursor to the SAM icon shown below (your icon can look
like either of these) and double-click the left mouse button.
6 The System Administration Manager window opens. Double-click on
Peripheral Devices ->.
7 The Peripheral Devices window opens. Double-click on Disks and File
Systems ->.
8 The Disks and File Systems window opens. Double-click on CD-ROM,
Floppy, and Hard Disks.
The following screen message appears:
Scanning the system’s hardware...
The CD-ROM, Floppy, and Hard Disks window opens containing a list of
drives currently configured on this system.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your CD-ROM Drive
Mounting and Unmounting a CD-ROM Disc
9 Highlight the disc you want to unmount and click on Remove a Hard
Disk Drive from the Actions menu.
10 A window with the following message opens:
Do you want to remove the disk?
Click on Yes.
11 Press the eject button on the CD-ROM drive and remove the CD-ROM
disc from the disc tray.
Reading the Busy Light
The CD-ROM busy light shows the status of the drive during the self test
and during activity with the host system.
The CD-ROM drive performs the self test when one of the following hap-
pens:
•
•
You load a disc and close the Disc Tray.
You turn on the workstation with a disc already loaded in the CD-ROM
drive.
For the self test, the busy light operates in the following sequence:
1 Light On - The busy light goes on when the disc loads into the
drive.
2 Light Flashing - The light flashes six times while a read test is per-
formed on the disc.
3 Light Off - The light goes off when the self test is complete.
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your CD-ROM Drive
Mounting and Unmounting a CD-ROM Disc
The busy light stays on after the self test when one of the following condi-
tions exist:
•
•
•
A defective disc
A disc insertion error (for example, an upside-down disc)
No disc present
The busy light goes off when one of the following conditions exist:
•
•
A CD-ROM drive power failure exists.
The drive is idle on the SCSI bus.
The busy light flashes during normal activity with the system.
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your CD-ROM Drive
Troubleshooting
Troubleshooting
If you have trouble with any of these procedures for using your CD-ROM
drive, see Chapter 6 of this book, “Solving Problems.”
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your CD-ROM Drive
Troubleshooting
62
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Using Your Digital Data Storage (DDS)
Tape Drive
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your Digital Data Storage (DDS) Tape Drive
This chapter describes how to perform tasks that archive to and transfer data
from the optional Digital Data Storage (DDS) tape drive. It also describes
how to maintain and care for the drive. We assume the DDS tape drive is set
to the factory default address of SCSI ID 3.
The instructions in this chapter assume you are using HP-UX version 9.05 or
later operating system with HP VUE version 3.0 or later interface.
This chapter provides information on the following:
•
•
•
•
DDS tape drive and data cassette descriptions
Operating the DDS Tape Drive
Troubleshooting
Ordering information
CAUTION:
Use only data cassettes labeled DDS cassettes. Never use audio cassettes labeled
DAT (Digital Audio Tape) in your DDS-format drive.
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your Digital Data Storage (DDS) Tape Drive
DDS Tape Drive and Data Cassette Descriptions
DDS Tape Drive and Data Cassette Descriptions
This section describes basic information needed for using your DDS tape
drive and data cassettes. Note that this drive is also referred to as a DDS-DC
drive, the DC standing for Data Compression.
DDS Drive
Your DDS tape drive is a 3.5-inch form factor DDS tape drive with data
compression and a SCSI interface. It conforms to the DDS format standard
for storing computer data, and incorporates a data compression capability.
It’s a high-capacity, high transfer-rate device for data storage on tape.
Controls and Indicators
Figure 14 shows the LEDs, power on/off button, and eject button of the DDS
drive.
Cassette LED
Drive LED
Eject Button
Figure 14
DDS Drive Controls and Indicators
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your Digital Data Storage (DDS) Tape Drive
DDS Tape Drive and Data Cassette Descriptions
LEDs
This section describes the LED codes that are displayed.
LEDs (light emitting diodes) indicate different activities or problems that
occur with your workstation DDS drive.
The front panel has two colored LEDs: Cassette and Drive. A green light
indicates normal operation, and an amber light indicates a warning condi-
tion. Pulsing shows activity between the drive and the SCSI bus.
If the Cassette Light (left LED) shows steady amber, it means that the cas-
sette is write-protected. If the Drive Light (right LED) shows steady amber,
this indicates a fault condition. Figure 15 lists the LED codes and their
meanings.
66
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your Digital Data Storage (DDS) Tape Drive
DDS Tape Drive and Data Cassette Descriptions
Key
Cassette
Drive
Meaning
OFF
Read/Write States
Write-Protect States
Error States
Cassette (un)loading
Green
Amber
Cassette loaded/online
Cassette loaded/activity
Pulsing Green
Cassette loaded/offline
Pulsing Amber
Pulsing Green
and Amber
Cassette (un)loading
Cassette loaded/online
Cassette loaded/activity
Cassette loaded/offline
Media wear (caution)
High humidity
Self-test (normal)
Self-test (failure)
Figure 15
DDS Tape Drive LED Display Codes
LED Warning Conditions
The following sections describe actions to take if the LEDs indicate a warn-
ing condition.
High Humidity If the LEDs display the high humidity signal, the humidity is
too high. The drive does not perform any operations until the humidity
drops.
Self-Test (Failure) If the LEDs display the self-test (failure) signal, a fault
was diagnosed during the self tests. Note the pattern of the pulses and con-
tact your local service representative.
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your Digital Data Storage (DDS) Tape Drive
DDS Tape Drive and Data Cassette Descriptions
Media Wear (Caution) Hewlett-Packard DDS drives continually monitor the
number of errors they have to correct when reading and writing to a tape to
determine tape wear and tape head cleanliness. If excessive tape wear or
dirty tape heads are suspected, the drive warns you by displaying the Media
Wear (Caution) signal on the LED indicators.
If the LED indicators on your DDS-format drive display the Media Wear
(Caution) condition, follow this procedure:
1
2
3
Check the system console for any tape error messages. A hard error during a read
or write operation may have occurred.
Clean the heads with a cleaning cassette (HP92283K) as described in the “Clean-
ing the Tape Heads” section, later in this chapter.
Repeat the operation you performed when the Media Wear (Caution) signal dis-
played. If the Media Wear (Caution) signal still displays, then the data cassette
should be replaced.
4
5
If you are performing a backup from disk to tape, discard the data cassette and
back up your files using a new data cassette.
If you are performing a restore from tape to disk, complete the restore, back up
the files to a new data cassette, then discard the data cassette
Data Cassettes
Media Life
HP DDS data cassettes are currently specified to 2000 passes over any part
of the tape under optimal environmental conditions (50% relative humidity,
22 degrees C). During a tape operation, any one area of the tape may have
multiple passes over the heads. This translates into approximately 200 to
300 backups or restores.
Under certain conditions, the life of your data cassette is less. Replace your
data cassettes after 100 backups or restores if your operating conditions meet
any of the following criteria:
•
The relative humidity in your operating environment is consistently less than
50%.
•
You know that the backup software you are using makes multiple passes over sec-
68
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your Digital Data Storage (DDS) Tape Drive
DDS Tape Drive and Data Cassette Descriptions
tions of the tape during backups or restores.
•
You notice that when you do backups and restores the tape stops and starts fre-
quently.
Cleaning the Tape Heads
Clean the heads of your tape drive after every 25 hours of tape drive use or if
the Media Wear (Caution) signal is displayed on the LED.
NOTICE:
Only use HP Cleaning Cassettes (HP92283K) to clean the tape heads. Do
not use swabs or other means of cleaning the tape heads.
Follow this procedure to clean the tape heads:
1
Insert the cleaning cassette into the drive. The tape automatically loads the cas-
sette and cleans the heads. At the end of the cleaning cycle, the drive ejects the
cassette.
2
Write the current date on the label on the cleaning cassette so that you know how
many times you have used it. Discard the cleaning cassette after you have used it
25 times.
Media Restrictions
If you interchange media between other HP workstation DDS tape drives,
note that data cassettes with compressed data can only be read by tape drives
that have data compression capabilities. This includes data cassettes that
contain both compressed and noncompressed data.
Setting the Write-Protect Tab on a Data Cassette
You can only store or change information on a data cassette when the write-
protect tab is in the write position. So, before trying to write to the data cas-
sette, make sure that the write-protect tab is in the write position, as shown
in Figure 16.
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your Digital Data Storage (DDS) Tape Drive
DDS Tape Drive and Data Cassette Descriptions
Push tab right
for write.
Push tab
left for
write-protect.
Figure 16
Setting the Write-Protect Tab on a DDS Tape
To protect information on a data cassette from being overwritten, set the
write-protect tab to the write-protect position, as shown in Figure 16.
NOTICE:
The write-protect tab should always be in the write position for transferring
data to a cassette.
70
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your Digital Data Storage (DDS) Tape Drive
Operating the DDS Tape Drive
Operating the DDS Tape Drive
This section describes how to perform tasks with your DDS tape drive.
Loading and Unloading a Data Cassette
Follow these steps to load and unload a data cassette from the DDS tape
drive:
1
2
Turn on power to the tape drive.
Insert the data cassette into the drive, as shown in Figure 17.
Eject Button
Figure 17
Loading and Unloading a Data Cassette
3
Push the data cassette about three quarters of the way into the drive. The drive
automatically pulls the data cassette the rest of the way in. When the LEDs on the
front of the drive stop flashing, the drive has loaded the data cassette.
4
To remove the data cassette, press and release the eject button on the front of the
drive, as shown in Figure 17. The LEDs on the drive flash on and off. Ten to twen-
ty seconds later, the data cassette slides partway out of the drive. Remove the cas-
sette from the drive.
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your Digital Data Storage (DDS) Tape Drive
Operating the DDS Tape Drive
Verifying the DDS Tape Drive Operation
To verify that your workstation can communicate with the DDS-format tape
drive, if you are using HP-UX 9.05, enter the following:
/etc/ioscan -d scsi
After a few moments the ioscan utility returns a message similar to the fol-
lowing:
H/W Path Description Status
======================================
2.0.1.3.0 tape_drive ok(nnnnnnnnn)
If you are using HP-UX 10.0, enter the following:
/usr/sbin/ioscan -d stape
After a few moments the ioscan utility returns a message similar to the fol-
lowing:
H/W Path
Class
Description
============================================
bc
8
bc
I/O Adapter
8/16
ba
Core I/O Adapter
Built-in SCSI
8/16/5
8/16/5.3
ext_bus
target
8/16/5.3.0 tape
HP HP35480A
If ioscan does not see your tape drive it will return the following message:
ioscan: No hardware found
If you receive this message, go to Chapter 6, “Solving Problems.”
72
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your Digital Data Storage (DDS) Tape Drive
Operating the DDS Tape Drive
Using Device Files
Your system has four default device files for use with your tape drive: two
device files for noncompressed mode and two device files for compressed
mode. If you use these device files, you do not need to create any device
files.
Device files are special files that tell your system which system hardware
pathway to use when communicating with a specific device and what kind of
device it is.
If the SCSI address of your tape drive is not set to the factory default of
SCSI ID 3, you must create a device file, then substitute the pathname of
your device file in the examples that follow. Refer to the System Administra-
tion Tasks manual for information on how to create a device file.
NOTICE:
The device file names used in these examples are appropriate only for
systems running HP-UX 9.05. If you are using HP-UX 10.0, the device file
names will depend on the naming conventions of your particular system.
See “SCSI ID and Device File Information for HP-UX 10.0” in Chapter 1
of this book.
Device Files — No Data Compression
Your system has two device files for using your tape drive with data com-
pression turned off. The device files are named /dev/rmt/3m and /dev/rmt/
3mn, and are set for SCSI ID 3.
If you use the /dev/rmt/3m device file, the tape drive rewinds the data cas-
sette every time the system releases the drive from its control.
If you use the /dev/rmt/3mn device file, the drive does not rewind the data
cassette. The tape stays where it was after the last operation.
If you use these device files, you do not need to create any device files.
Device Files — Data Compression
If you wish to use the data compression feature, use the device files /dev/
rmt/3hc and /dev/rmt/3hcn, which are set for SCSI ID 3.
If you use the /dev/rmt/3hc device file, the tape drive compresses the data
and rewinds the data cassette every time the system releases the drive from
its control.
73
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your Digital Data Storage (DDS) Tape Drive
Operating the DDS Tape Drive
If you use the /dev/rmt/3hcn device file, the drive compresses the data, but
does not rewind the data cassette. The tape stays where it was left after the
last operation.
If you use these device files, you do not need to create any device files.
Archiving Data in Compressed and Noncompressed Mode
This section describes how to transfer data to and from a DDS- format data
cassette (saving and restoring) using the HP-UX tar command and your tape
drive’s device file.
NOTICE:
Before using your DDS-format tape drive to back up your file system,
make sure you read the “Media Interchangeability Restrictions” section
later in this chapter.
The tar (tape file archiver) command allows you to save files to a data cas-
sette, restore files from a data cassette to your system, or list the files on your
data cassette.
The examples in this chapter use the device file /dev/rmt/3m, which
archives the data in noncompressed mode and causes the drive to rewind the
data cassette. To use data compression, substitute
/dev/rmt/3hc for /dev/rmt/3m. If you named your device files differently,
substitute the correct file name where appropriate.
NOTICE:
A DDS-format tape drive with data compression capability is labeled
DCLZ on its front panel.
Writing to a Data Cassette
Use the following instructions to save files to a data cassette:
1
2
3
Check that the write-protect tab on the data cassette is in the write position.
Load the data cassette into the tape drive.
Click on the Terminal Control on the Front Panel of your Workspace.
A terminal window opens.
74
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your Digital Data Storage (DDS) Tape Drive
Operating the DDS Tape Drive
4
5
Move the mouse cursor into the terminal window and click the left mouse button.
Enter the following command line to write to the tape:
tar -cvf /dev/rmt/3m pathname
where pathname is the pathname of the file or directory containing files that you
want to write to the tape. To use the data compression mode, substitute /dev/
rmt/3hc for /dev/rmt/3m.
Restoring Files from a Data Cassette to Your System
Use the following instructions to restore files from a data cassette to your
system:
1
2
Load the data cassette into the tape drive.
Click on the Terminal Control on the Front Panel of your Workspace.
A terminal window opens.
3
4
5
Move the mouse cursor into the terminal window and click the left mouse button.
Use cd to change to the directory you want the files to reside in.
Enter the following command line to restore data:
tar -xvf /dev/rmt/3m pathname
where pathname is the pathname of the file or directory containing files that you
want to restore from the tape. If pathname is not specified, everything on the
data cassette is restored. To use the data compression mode, substitute /dev/rmt/
3hc for /dev/rmt/3m.
Listing the Files on a Data Cassette
Use the following instructions to list the files on a data cassette:
1
2
Load the data cassette into the tape drive.
Click on the Terminal Control on the Front Panel of your Workspace.
A terminal window opens.
3
Move the mouse cursor into the terminal window and click the left mouse button.
75
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your Digital Data Storage (DDS) Tape Drive
Operating the DDS Tape Drive
4
Enter the following command line to receive a file listing of the data cassette:
tar -tvf /dev/rmt/3m
To use the data compression mode, substitute /dev/rmt/3hc for /dev/rmt/3m.
Further Command Information
For additional information on using tar and a complete list of the command
arguments, refer to the tar man page by typing the following:
man tar
The man utility looks up man pages on the system.
You may also communicate with the tape drive with the cpio, ftio, mt, and
fbackup commands. For more information on these commands, enter the
following in a terminal window:
man command
Media Interchangeability Restrictions
If you interchange media between DDS-format tape drives, the following
two restrictions apply to the media:
•
Data cassettes with compressed data can only be read by tape drives which have
data compression capabilities, such as the tape drive (part number C1504-67201)
found in Kit A2275A #AHS. This includes data cassettes that contain both com-
pressed and noncompressed data.
•
Use 90-meter data cassettes only in the 3.5-inch form factor DDS-format tape
drives found in Kit A2274A #AHS (part number C1503-67201) and Kit A2275A
#AHS (part number C1504-67201). The full height (5 1/4-in) DDS-format tape
drives cannot read or write to 90-meter data cassettes.
76
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your Digital Data Storage (DDS) Tape Drive
Troubleshooting
Troubleshooting
If you have trouble with any of these procedures for using your DDS tape
drive, see Chapter 7 of this book, “Solving Problems.”
77
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your Digital Data Storage (DDS) Tape Drive
Ordering Information
Ordering Information
To order Hewlett-Packard data cassettes and cleaning cassettes for use in
your DDS tape drive, use the following order numbers:
•
•
•
HP92283A Box of five 60-meter DDS data cassettes
HP92283B Box of five 90-meter DDS data cassettes
HP92283K Package of two cleaning cassettes
CAUTION:
Use only data cassettes labeled as DDS cassettes. Never use audio cassettes labeled
DAT (Digital Audio Tape) in your DDS-format drive.
78
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Using Your 3.5-Inch Floppy Disk Drive
79
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your 3.5-Inch Floppy Disk Drive
This chapter describes how to perform tasks that allow you to archive to or
transfer data from the optional 3.5-inch floppy disk drive. The information is
organized into the following sections:
•
•
•
•
Using the floppy diskette
Operating the floppy drive
Troubleshooting
Ordering information
The instructions in this chapter assume you are using HP-UX version 9.05 or
later operating system with HP VUE version 3.0 or later interface.
NOTICES:
When examples of user input are given in this chapter, enter them at the
command-line prompt in an HP VUE terminal window or HP-UX shell.
Some procedures in this chapter require you to log in as root. If you cannot
log in as root, contact your system administrator.
80
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your 3.5-Inch Floppy Disk Drive
Using the Floppy Diskette
Using the Floppy Diskette
This section describes basic information needed for using your floppy dis-
kettes.
Setting the Write-Protect Tab on a Diskette
You can only store or change information on a diskette when the write-pro-
tect tab is in the write position. So, before trying to write to the diskette,
make sure that the write-protect tab is in the write position, as shown in Fig-
ure 18.
Push tab up
for write.
Push tab
down for
write-protect
Figure 18
Setting the Write-Protect Tab on a Floppy Diskette
To protect files on a diskette from being overwritten, set the write-protect tab
to the write-protect position, as shown in Figure 18.
NOTICE:
The write-protect tab should always be in the write position for formatting
a new diskette and transferring data to a diskette.
81
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your 3.5-Inch Floppy Disk Drive
Using the Floppy Diskette
Inserting and Removing a Diskette
Follow these steps to insert and remove a diskette from the floppy disk drive:
1
Insert the diskette into the drive, as shown in Figure 19.
Eject Button
Figure 19
Inserting and Removing a Floppy Diskette
2
Push the diskette into the floppy drive until it clicks into place.
3
To remove the diskette, push the eject button (Figure 19), then take out the dis-
kette.
82
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your 3.5-Inch Floppy Disk Drive
Operating the Floppy Drive
Operating the Floppy Drive
This section describes how to perform tasks with your 3.5-inch floppy disk
drive.
Verifying the Floppy Drive Configuration
To verify that your workstation can communicate with the floppy drive, use
the ioscan command in a terminal window to see which devices are cur-
rently in use on your system. The following are examples of using ioscan for
version 9.05 and version 10.0:
1
Click on the Terminal Control on the Front Panel of your Workspace.
Terminal Control
A terminal window opens.
2
3
Move the mouse cursor into the terminal window and click the left mouse button.
Enter the following at the prompt:
/etc/ioscan (for 9.05)
ioscan (for 10.0)
83
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your 3.5-Inch Floppy Disk Drive
Operating the Floppy Drive
After a few moments the ioscan utility lists all of the I/O devices it could
find. If there is a floppy drive in the list, that listing appears similar to the
following:
Example of version 9.05 output:
H/W Path
Description Status
========================================
2.0.10
floppy
disk
ok(nnnnnn)
ok(nnnnnn)
2.0.10.1.0
2.0.10 floppy is the floppy controller. 2.0.10.1.0 disk is the floppy drive.
Example of version 10.0 output:
H/W Path
Class
Description
============================================
8
bc
I/O Adapter
8/0
graphics
unknown
Graphics
8/16/10
Built-in Floppy Drive
Using Device Files
Device files are special files that tell your system which pathway to use
through the system hardware when communicating with a specific device
and what tell kind of device it is.
Your workstation uses the following device file to communicate with the
floppy drive:
/dev/rfloppy/c20Ad1s0
84
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your 3.5-Inch Floppy Disk Drive
Operating the Floppy Drive
Formatting a New Diskette
You must always format a new floppy diskette with the mediainit utility
before using it. To format a new floppy diskette follow these steps:
1
2
Log in as root.
Make sure that the write-protect tab on the floppy diskette is in the write position,
as shown in Figure 18.
3
4
Insert the diskette into the floppy disk drive.
Click on the Terminal Control on the Front Panel of your Workspace.
Terminal Control
A terminal window opens.
5
6
Move the mouse cursor into the terminal window and click the left mouse button.
Execute mediainit with an interleave of 2 by entering the following:
mediainit -i 2 /dev/rfloppy/c20Ad1s0
85
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your 3.5-Inch Floppy Disk Drive
Operating the Floppy Drive
Transferring Data To and From a Floppy Diskette
This section describes how to transfer data to and from your floppy diskette
(saving and restoring) using the HP-UX tar command with your floppy
drive’s device file.
The tar (tape file archiver) command saves files to a floppy diskette, restores
files from a floppy diskette, or lists files on a floppy diskette.
You need to set the write protect tab to the write position to transfer data to
the diskette. The write-protect tab can be in either position when restoring
data from a diskette or listing the files on a diskette.
Saving Files to a Floppy Diskette
Use the following instructions to save files to a floppy diskette:
1
2
3
Check that the write-protect tab on the floppy diskette is in the write position.
Load the formatted floppy diskette into the disk drive.
Click on the Terminal Control on the Front Panel of your Workspace.
Terminal Control
A terminal window opens.
4
Move the mouse cursor into the terminal window and click the left mouse button.
86
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your 3.5-Inch Floppy Disk Drive
Operating the Floppy Drive
5
Enter the following command line to write to the diskette:
tar -cvf /dev/rfloppy/c20Ad1s0 pathname
where pathname is the pathname of the file or directory containing files that you
want to write to the diskette.
Restoring Files from a Floppy Diskette to Your System
Use the following instructions to restore files from a floppy diskette to your
system:
1
2
Load the floppy diskette into the disk drive.
Click on the Terminal Control on the Front Panel of your Workspace.
Terminal Control
A terminal window opens.
3
4
Move the mouse cursor into the terminal window and click the left mouse button.
Use the cd command to change to the directory you want the files to reside in:
cd directory_path
where directory_path is the pathname of the directory.
87
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your 3.5-Inch Floppy Disk Drive
Operating the Floppy Drive
5
Enter the following command line:
tar -xvf /dev/rfloppy/c20Ad1s0 pathname
where pathname is the pathname of the file or directory containing files that you
want to restore from the diskette. If you don’t specify pathname, everything on
the floppy diskette is restored.
Listing the Files on a Floppy Diskette
Use the following instructions to list the files on a floppy diskette:
1
2
Load the floppy diskette into the disk drive.
Click on the Terminal Control on the Front Panel of your Workspace.
Terminal Control
A terminal window opens.
3
4
Move the mouse cursor into the terminal window and click the left mouse button.
Enter the following command line:
tar -tvf /dev/rfloppy/c20Ad1s0
All files on the floppy diskette are listed.
88
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your 3.5-Inch Floppy Disk Drive
Operating the Floppy Drive
For More Information
For more information on using tar and a complete list of the command argu-
ments, refer to the tar man page by typing the following in a terminal win-
dow:
man tar
The man utility looks up man pages on the system.
You can mount the floppy drive as a file system using the SAM utility. Be
sure to unmount the drive before removing it as a file system. For more
information about how to mount and unmount the floppy drive, see the man-
ual Using HP-UX (B2910-90001).
For more information on copying data to or from your system to other
media, including your floppy diskette, refer to the cpio man page by typing
the following in a terminal window:
man cpio
For more information on copying to or from DOS files, refer to the doscp
man page by typing the following in a terminal window:
man doscp
For more information on listing the contents of DOS directories, refer to the
dosls man page by typing the following in a terminal window:
man dosls
For more information on using your floppy disk drive and floppy diskettes,
refer to the floppy man page by typing the following in a terminal window:
man floppy
For more information on using the mediainit command, refer to the medi-
ainit man page by typing the following in a terminal window:
man mediainit
89
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your 3.5-Inch Floppy Disk Drive
Operating the Floppy Drive
Configuring the Floppy Driver
If you reload software or rebuild the Instant Ignition system on your work-
station, you need to reconfigure the HP-UX Kernel to add the floppy driver.
Use the SAM utility to add the flexible disk driver and build a new HP-UX
kernel.
For more information about how to reconfigure the kernel using SAM, see
the following manuals:
•
•
System Administration Tasks HP 9000 Series 700 Computers (B2355-90040)
Using HP-UX (B2910-90001)
90
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your 3.5-Inch Floppy Disk Drive
Troubleshooting
Troubleshooting
If you have trouble with any of these procedures for using your floppy disk
drive, see Chapter 6 of this book, “Solving Problems.”
Ordering Information
To order Hewlett-Packard micro flexible diskettes for use in your 3.5-inch
floppy disk drive, use the following order number:
HP-92192X
High-Density Micro Flexible Disks
(1.44MB Formatted Capacity) - box of ten diskettes
91
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your 3.5-Inch Floppy Disk Drive
Ordering Information
92
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Solving Problems
93
Download from Www.Somanuals.com. All Manuals Search And Download.
Solving Problems
This chapter contains information to help you determine what’s wrong with
your system when you have problems. If you have a problem that isn’t listed
in this chapter, or if your problem persists, contact your designated service
representative. When calling for service, always have your system’s model
number and serial number ready.
This chapter is divided into the following sections
•
•
•
Common problems and solutions
Dealing with a boot failure
Running system verification tests
The instructions in this chapter assume you are using HP-UX version 9.05 or
later operating system with HP VUE version 3.0 or later interface.
94
Download from Www.Somanuals.com. All Manuals Search And Download.
Solving Problems
Common Problems and Solutions
Common Problems and Solutions
The tables in this section list common problems you may encounter with
your workstation. The tables also tell you what to do to help solve the prob-
lems.
Problems with Powering Up the System
Table 6 describes possible problems you may encounter when powering up
the system and offers solutions.
Table 6
Power Up Problems
Problem
Solution
The power LED does not Make sure all AC power cables are connected securely to
light.
the system.
Make sure the power cord is plugged into a working AC
outlet.
Make sure the power switch is set to the ON position.
The power LED lights,
Press the brightness control on the monitor to adjust it. If
but the screen is blank or the screen is still blank, turn off the system and monitor
flickers.
power switches. When the system is completely powered
off, check the video cable connections.
Go to the section "Changing Your Monitor Type" in Appen-
dix B for information about displaying and setting your
workstation’s monitor configuration.
If the problem persists, contact your system administrator or call your designated service
representative.
95
Download from Www.Somanuals.com. All Manuals Search And Download.
Solving Problems
Common Problems and Solutions
Problems Loading and Booting the Operating System
Table 7 describes possible problems you may encounter when loading and
booting the operating system and offers solutions.
Table 7
Problems Loading and Booting the Operating System
Problem
Solution
The power LED is lit,
and text appears on the
screen, but more than two
minutes have passed with
no sign of system activ-
ity.
Make sure that all SCSI devices are set to the proper SCSI
ID. (See Appendix C for default SCSI ID settings.)
Check that all SCSI devices are correctly cabled. Check that
the SCSI bus is correctly terminated. (See Appendix C for
information on SCSI cabling and termination).
The system stops or
hangs while booting.
Follow the instructions in "Dealing With a Boot Failure" in
this chapter.
If problem persists, contact your system administrator or call your designated service
representative.
Problems with the 802.3 Network
Table 8 describes possible problems you may encounter with the 802.3 net-
work and offers solutions.
Table 8
Problems with the 802.3 Network
Problem
Solution
Cannot reach other sys-
tems on the network.
Applications that rely on
the network will not run.
Check the network connector on the back of the system unit.
Make sure that the network cable or transceiver is fastened
securely to the connector.
If problem persists, contact your system administrator or call your designated service
representative.
96
Download from Www.Somanuals.com. All Manuals Search And Download.
Solving Problems
Common Problems and Solutions
Problems Using a Hard Disk Drive
Table 9 describes possible problems you may encounter using the hard disk
drive and offers solutions.
Table 9
Problems Using a Hard Disk Drive
Problem
Solution
The disk drive is not
accessible or does not
respond.
Make sure that all the SCSI devices are set to the proper
SCSI ID. (See Appendix C for default SCSI ID settings.)
Check that all SCSI devices are correctly cabled. Check that
the SCSI bus is correctly terminated. (See Appendix C for
information on SCSI cabling and termination.)
Make sure that the system can communicate with the drive
as described in "Checking the SCSI IDs" in Appendix B.
Follow the instructions in "Dealing With a Boot Failure" in
this chapter.
If problems persist, contact your system administrator or call your designated service
representative.
97
Download from Www.Somanuals.com. All Manuals Search And Download.
Solving Problems
Common Problems and Solutions
Problems Using the CD-ROM Drive
Table 10 describes a possible problem you may encounter when you use the
CD-ROM drive and offers a solution.
Table 10
Problems Using the CD-ROM Drive
Problem
Solution
The CD-ROM drive
does not respond to com-
mands.
Re-enter the commands and make sure that you have typed
them correctly.
Make sure that the system can communicate with the drive
as described in "Checking the SCSI IDs" in Appendix B.
Follow the instructions in the section "Running the System
Verificatin Tests" in this chapter to verify that the CD-ROM
drive is functioning properly.
If problems persist, contact your system administrator or call your designated service
representative
98
Download from Www.Somanuals.com. All Manuals Search And Download.
Solving Problems
Common Problems and Solutions
Problems Using the DDS Tape Drive
Table 11 describes a possible problem you may encounter using the DDS
tape drive and offers solutions.
Table 11
Problems Using the DDS Tape Drive
Problem
Solution
The DDS tape drive does Re-enter the commands and make sure that you have typed
not respond to com-
mands.
them correctly.
Make sure that you specified the correct device file name for
commands that require a device file name.
Make sure the write-protect tab is set to write if you are try-
ing to copy data to a data cassette.
Make sure that the system can communicate with the drive
as described in "Checking the SCSI IDs" in Appendix B.
Follow the instructions in the section "Running the System
Verification Tests" in this chapter to verify that the tape
drive is functioning properly.
If the problem persists, contact your system administrator or call your designated service
representative.
99
Download from Www.Somanuals.com. All Manuals Search And Download.
Solving Problems
Common Problems and Solutions
Problems Using the Floppy Disk Drive
Table 12 describes a possible problem you may encounter using the floppy
disk drive and offers a solution.
Table 12
Problems Using the Floppy Disk Drive
Problem
Solution
The floppy drive does not Re-enter the commands and make sure that you have typed
respond to commands.
them correctly.
Make sure that you specified the device file
/dev/rfloppy/c301d0s0 for commands that require a device
file name.
Make sure that the write-protect tab is set to write if you are
trying to copy data to a floppy diskette.
Follow the instructions in the section "Running the System
Verification Tests" in this chapter to verify that the floppy
drive is functioning properly.
If the problem persists, contact your system administrator or call your designated service
representative.
100
Download from Www.Somanuals.com. All Manuals Search And Download.
Solving Problems
Dealing with a Boot Failure
Dealing with a Boot Failure
If your usual boot device (typically a disk) is not responding as it should,
you must try to boot from the disk (or another boot device) by selecting it
manually.
To boot a device manually, follow these steps:
1
Follow the directions in “Accessing the Boot Console Interface,” in Appendix D
of this book.
NOTICE:
Your workstation automatically shuts down the operating system
before it terminates the power.
2
At the Main Menu prompt, type the following:
Main Menu: Enter a command or a menu > search ipl
This causes your workstation to search exhaustively for bootable media.
The search command looks for bootable media on your workstation.
3
4
Boot from one of the listed devices by typing the following at the prompt:
Main Menu: Enter a command or a menu > boot device
where device is the hardware path to the device, specified in mnemonic style
notation, such as scsi.5.0
If your workstation still fails to boot, there is either something wrong with the file
system or with the hardware. If you suspect a file system failure, see the manual
Using HP-UX for help on dealing with file system failures. If you think that some-
thing is wrong with the hardware, continue reading this chapter for more trouble-
shooting information.
101
Download from Www.Somanuals.com. All Manuals Search And Download.
Solving Problems
Running System Verification Tests
Running System Verification Tests
HP-UX uses a diagnostics product called SupportWave. SupportWave con-
tains the Support Tools Manager so that you can verify your system opera-
tion.
You can access the Support Tools Manager in a terminal window. If you are
using HP VUE as your interface, you can also access the Support Tools
Manager through the sys_admin directory.
Three interfaces are available with the Support Tools Manager: a command
line interface (accessed through the cstm command), a menu-driven inter-
face (accessed through the mstm command), and the graphical user interface
(accessed through the xstm command).
For more information on SupportWave user interfaces, see the on-line man
pages by entering the following at a command line prompt:
man cstm
man mstm
man xstm
102
Download from Www.Somanuals.com. All Manuals Search And Download.
Solving Problems
Running System Verification Tests
To run SupportWave from either HP VUE or the HP-UX command line
shell, perform the following steps:
1
Click on the Terminal Control on the Front Panel of your Workspace.
Terminal Control
A terminal window opens.
2
3
Move the mouse cursor into the terminal window and click the left mouse button.
Enter the following at the prompt:
cstm
The following screen appears:
************************************************************
******
******
******
******
******
******
******
******
******
******
******
******
******
******
******
******
******
******
******
******
******
******
******
******
SUPPORT TOOLS MANAGER
Command Line Interface
Version x.xx.xx
Part Number xxxxx-xxxxx
(C) Copyright Hewlett Packard Co. xxxx
All Rights Reserved
************************************************************
Please Wait. System mapping in progress . . .
Please type HELP or ? to list available commands.
CSTM>
4
At the CSTM>prompt, you can enter several commands. To see what commands
are available, type the help command.
103
Download from Www.Somanuals.com. All Manuals Search And Download.
Solving Problems
Running System Verification Tests
5
To verify the system operation, type the following at the CSTM> prompt:
CSTM> verify all
The following messages appear:
Verification has started on device (CPU).
Verification has started on device (FPU).
Verification has started on device (0/0/0).
Verification has started on device (2/0/1.0.0).
Verification has started on device (2/0/1.5.0).
Verification has started on device (2/0/1.6.0).
Verification has started on device (2/0/2).
CSTM>Message from (0/0/0):
This graphics test displays a number of graphics images on the
screen of the graphics device being tested. If an X server is
not currently running on that display, X Windows will be started
and run for the duration of the test. The Starbase shared li-
brary (/usr/lib/libsbisl) should be present to run this test.
CAUTION: This test will fail if any portion of the test window
is modified or overlaid in any way.
NOTE: If a VUE login screen is currently displayed on the mon-
itor, the test will wait until someone logs in the HP VUE on the
graphics monitor to release the lock. The test stops if the
Screen Saver times out, it runs again once the Screen is acti-
vated.
WARNING: Do not run this exercise with any other option.
(Type ’R’ for Ready, Type ’S’ for Skip) [R] >>
6
When you see the >> prompt shown above, enter r
The following messages and a graphics test window appear:
Verification of (2/0/1.0.0) has completed. Result status - (Success)
Verification of (2/0/1.5.0) has completed. Result status - (Success)
Verification of (2/0/1.6.0) has completed. Result status - (Success)
Verification of (CPU) has completed. Result status - (Success)
Verification of (FPU) has completed. Result status - (Success)
Verification of (2/0/2) has completed. Result status - (Success)
Verification of (0/0/0) has completed. Result status - (Success).
7
8
Press Enter to return to the CSTM>prompt after all test results are reported.
To exit the Support Tools Manager, enter the following:
CSTM> exit
If any tests failed, further diagnosis is necessary by qualified service personnel.
Contact your designated service representative.
104
Download from Www.Somanuals.com. All Manuals Search And Download.
A
Safety and Regulatory Statements
105
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety and Regulatory Statements
This appendix contains safety and regulatory statements pertaining to your
C100/C110 workstation. It provides information on the following topics:
•
•
•
•
•
•
•
•
Emissions regulations
Emissions regulations compliance
Datacom users statement
Acoustics
Electrostatic discharge (ESD) precautions
Safety statements
Laser safety statements
Warnings and cautions
106
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety and Regulatory Statements
Emissions Regulations
Emissions Regulations
Federal Communications Commission (FCC)
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules and the Cana-
dian Department of Communications. These limits are designed to provide
reasonable protection against harmful interference in a residential installa-
tion. This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guaran-
tee that interference will not occur in a particular installation. If this equip-
ment does cause harmful interference to radio or television reception
(determined by turning the equipment off and on), you can correct the inter-
ference by one or more of the following measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•
Ask the dealer or an experienced radio/television technician for help.
Hewlett-Packard’s system certification tests were conducted with HP-sup-
ported peripheral devices and HP shielded cables, such as those you receive
with your computer. Changes or modifications not expressly approved by
Hewlett-Packard could void the user’s authority to operate the equipment.
Operation of this device is subject to the following conditions:
•
•
This device may not cause harmful interference.
This device must accept interference received, including interference that may
cause undesired operation.
•
Cables used with this device must be properly shielded to comply with the re-
quirements of the FCC.
107
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety and Regulatory Statements
Emissions Regulations Compliance
VCCI Class 2 ITE
Emissions Regulations Compliance
Any third-party I/O device installed in HP system(s) must be in accordance
with the requirements set forth in the preceding Emissions Regulations state-
ments. In the event that a third-party noncompliant I/O device is installed,
the customer assumes all responsibility and liability arising therefrom.
Acoustics
Regulation On Noise Declaration For Machines -3. GSGV
Lpa <70dB
Lpa<70dB
operator position
normal operation
per ISO 7779
am Arbeitsplatz
normaler Betrieb
nach DIN 45635 T.19
108
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety and Regulatory Statements
Electrostatic Discharge (ESD) Precautions
Electrostatic Discharge (ESD) Precautions
Electrostatic charges can damage the integrated circuits on printed circuit
boards. To prevent such damage from occurring, observe the following pre-
cautions during board unpacking and installation:
•
•
Stand on a static-free mat.
Wear a static strap to ensure that any accumulated electrostatic charge is dis-
charged from your body to ground.
•
Connect all equipment together, including the static-free mat, static strap, routing
nodes, and peripheral units.
•
•
Keep uninstalled printed circuit boards in their protective antistatic bags.
Handle printed circuit boards by their edges, once you have removed them from
their protective antistatic bags.
109
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety and Regulatory Statements
Safety Statement
Safety Statement
This equipment conforms to the following safety standards:
•
•
•
•
UL 1950
CSA 950
IEC 950
EN 60950
110
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety and Regulatory Statements
Laser Safety Statement (U.S.A. Only)
Laser Safety Statement (U.S.A. Only)
The CD ROM mass-storage system is certified as a Class-1 laser product
under the U.S. Department of Health and Human Services (DHHS) Radia-
tion Performance Standard according to the Radiation Control for Health
and Safety Act of 1968.
This means that the mass-storage system does not produce hazardous laser
radiation. Because laser light emitted inside the mass-storage system is com-
pletely confined within protective housings and external covers, the laser
beam cannot escape from the machine during any phase of user operation.
111
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety and Regulatory Statements
Warnings and Cautions
Warnings and Cautions
112
Download from Www.Somanuals.com. All Manuals Search And Download.
B
Changing Your Workstation’s
Hardware Configuration
113
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing Your Workstation’s Hardware Configuration
This appendix describes the procedures to change your workstation’s hard-
ware configuration. It presents the information in the following sections:
•
•
•
•
•
•
•
•
Checking the SCSI IDs
Preparing your workstation
Installing storage devices
Removing the main tray assembly
Replacing the main tray assembly
Installing additional memory
Installing an EISA or GSC option board
Changing your monitor type
The instructions in this chapter assume you are using HP-UX version 9.05 or
later operating system with HP VUE version 3.0 or later interface.
NOTICE:
Your workstation shipped with a package of extra disk slides. Keep the
slides in a safe place, you will need them when you add new devices to the
storage tray.
CAUTION:
Always wear a properly grounded wrist strap when reconfiguring your
workstation.
Use the following tools to remove or replace hardware parts when changing
your configuration:
•
•
Light-duty flat blade screwdriver with 150 mm (6 in.) blade
Needlenose pliers
Also, read the ESD Precautions in Appendix A of this guide.
114
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing Your Workstation’s Hardware Configuration
Checking the SCSI IDs
Checking the SCSI IDs
To determine which SCSI IDs are currently in use on your system, use the
ioscan command in a terminal window:
1
Click on the Terminal Control on the Front Panel of your Workspace.
A terminal window opens.
2
3
Move the mouse cursor into the terminal window and single-click the left mouse
button.
If you are using HP-UX 9.05 or greater, enter the following at the prompt:
/etc/ioscan -d scsi
After a few moments the ioscan utility lists all of the SCSI I/O devices it could
find. The list should appear similar to the following:
H/W Path
=============================================
2.0.1.2.0 cd-rom_drive ok(nnnnnnnn)
Description
Status
If you are using HP-UX 10.0, enter the following at the prompt:
/usr/sbin/ioscan -f
115
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing Your Workstation’s Hardware Configuration
Checking the SCSI IDs
After a few moments the ioscan utility lists all of the SCSI I/O devices it could
find. The list appears similar to the following:
Class
I
H/W Path
Driver
S/W State H/W Type
Description
=============================================================================================
bc
bc
0
1
0
root
ccio
c720
CLAIMED
CLAIMED
CLAIMED
BUS_NEXUS
8
8/0
BUS_NEXUS I/O Adapter
INTERFACE GSC built-in Fast/Wide SCSI
ext_bus
Interface
target
disk
0
3
1
2
2
0
0
2
0
0
1
3
1
4
0
5
10
6
5
0
0
2
3
7
6
2
1
0
1
2
4
8
9
10
0
0
8/0.0
tgt
CLAIMED
CLAIMED
CLAIMED
CLAIMED
CLAIMED
CLAIMED
DEVICE
8/0.0.0
8/0.5
sdisk
tgt
DEVICE
DEVICE
DEVICE
DEVICE
DEVICE
QUANTUM LPS1080WD
target
disk
8/0.5.0
8/0.6
sdisk
tgt
DEC
DEC
DSP3210SW
DSP3210SW
target
disk
8/0.6.0
8/16
sdisk
ba
bus_adapterCLAIMED
BUS_NEXUS Core I/O Adapter
INTERFACE Built-in Parallel Interface
INTERFACE Built-in Audio
INTERFACE Built-in RS-232C
INTERFACE Built-in SCSI
DEVICE
DEVICE
DEVICE
DEVICE
DEVICE
DEVICE
DEVICE
DEVICE
INTERFACE Built-in LAN
INTERFACE Built-in Keyboard/Mouse
BUS_NEXUS I/O Adapter
INTERFACE GSC Fast/WideSCSI Interface
DEVICE
DEVICE
ext_bus
audio
tty
8/16/0
CentIf
audio
asio0
c700
tgt
CLAIMED
CLAIMED
CLAIMED
CLAIMED
CLAIMED
CLAIMED
CLAIMED
CLAIMED
CLAIMED
CLAIMED
CLAIMED
CLAIMED
CLAIMED
CLAIMED
CLAIMED
CLAIMED
CLAIMED
CLAIMED
CLAIMED
8/16/1
8/16/4
ext_bus
target
disk
8/16/5
8/16/5.2
8/16/5.2.0
8/16/5.3
8/16/5.3.0
8/16/5.4
8/16/5.4.0
8/16/5.6
8/16/5.6.0
8/16/6
sdisk
tgt
TOSHIBA CD-ROM XM-4101TA
target
tape
stape
tgt
HP HP35480A
target
disk
sdisk
tgt
SEAGATE ST3600N
MICROP 2112
target
disk
sdisk
lan2
ps2
lan
ps2
8/16/7
bc
10
ccio
c720
tgt
sdisk
graph3
bus_adapterCLAIMED
hil
ext_bus
target
disk
10/12
10/12.4
10/12.4.0
10/16
SEAGATE ST31200W
graphics
ba
INTERFACE Graphics
BUS_NEXUS Core I/O Adapter
INTERFACE Built-in HIL
INTERFACE Built-in RS-232C
BUS_NEXUS EISA Bus Adapter
INTERFACE EISA card HWP0C70
DEVICE
8/20
hil
8/20/1
CLAIMED
CLAIMED
CLAIMED
CLAIMED
CLAIMED
CLAIMED
CLAIMED
tty
8/20/2
asio0
eisa
hshpib
tgt
tgt
tgt
ba
8/20/5
ext_bus
target
target
target
processor
memory
8/20/5/3
8/20/5/3.0
8/20/5/3.1
8/20/5/3.2
32
DEVICE
DEVICE
processor CLAIMED
memory
PROCESSOR Processor
49
CLAIMED
MEMORY
Memory
4
If you are using HP-UX 9.05 or greater, you can find out the SCSI IDs currently
in use by looking under the H/W Path heading. The listing 2.0.1 scsi is the built-
in SCSI bus controller. For devices connected to the built-in SCSI bus, such as
disks, the fourth number is the SCSI ID for that device. For example, the listing
2.0.1.6.0 in the sample device list tells you that there is a SCSI device (a disk)
currently using ID 6 on the SCSI bus.
Although the information is presented in a different format if you are using HP-
UX 10.0, you also look under the H/W Path heading.
NOTICE:
Never use SCSI address 7 for any device. Address 7 is reserved for the
SCSI controller.
116
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing Your Workstation’s Hardware Configuration
Preparing Your Workstation
Preparing Your Workstation
This section describes how to prepare your workstation for changing its con-
figuration. Use the following procedure to prepare your workstation:
1
Power off your workstation by pressing the power button on the front panel.
When you press the power button, the workstation automatically shuts down the
operating system before it powers off the system.
2
3
When the workstation has completed shutting down and powering off, power off
the monitor, and any peripheral devices connected to the workstation.
Unplug the power cord of the system unit, the monitor, and any peripheral devic-
es from ac wall outlets.
4
5
Unplug the power cord from the back of the system unit.
Remove the floor stand from the system unit, as shown in Figure 20.
117
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing Your Workstation’s Hardware Configuration
Preparing Your Workstation
Figure 20
Removing the Floor Stand
6
7
Lay the system unit on a flat surface, such as a table top.
Attach a static-grounding wrist strap to bare metal on the back of the system unit.
118
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing Your Workstation’s Hardware Configuration
Installing Storage Devices
Installing Storage Devices
This section describes how to install storage devices in your workstation.
Before installing a new storage device, perform the following procedures as
described earlier in this chapter:
•
•
Checking the SCSI IDs
Preparing Your Workstation
CAUTION:
NOTICE:
All storage devices are susceptible to mechanical and electrostatic shock. When
handling the devices, always wear the static-grounding wrist strap that came in the
storage device kit. Always handle the drive carefully.
Do not use SCSI ID 7 for any of your storage devices’ SCSI addresses. The
host SCSI controllers use SCSI ID 7.
119
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing Your Workstation’s Hardware Configuration
Installing Storage Devices
Preparing to Install Your Storage Device
This section describes information that you need to consider and procedures
that you need to perform before installing any storage device.
Configuring your Storage Device
Table 13 lists the recommended SCSI IDs for internal storage devices. If an
existing device already uses one of the suggested IDs, select an alternate ID.
Table 13
Default SCSI IDs
Fast/Wide Differential SCSI Devices
SCSI ID
1st Hard Disk Drive
2nd Hard Disk Drive
3rd Hard Disk Drive
6
5
4
Single-Ended SCSI-2 Devices
SCSI ID
CD-ROM Drive
2
3
DDS-Format Tape Drive
NOTE: The floppy drive is not a SCSI device.
Set the jumpers and SCSI IDs according to the installation instructions that
came with your device.
Determining Your Storage Devices Position
Each storage device is restricted as to where in the storage tray it may be
installed. Before installing a storage device, use Figure 21 and Table 14 to
determine which disk tray position is correct for your device.
Figure 21 shows the storage device positions in the disk tray. Table 14 lists
what devices are supported in the different disk tray positions. The numbers
in the table’s left column refer to the position numbers in Figure 21.
120
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing Your Workstation’s Hardware Configuration
Installing Storage Devices
Figure 21
Table 14
Disk Tray Positions
Storage Configurations
Disk
Tray
Supported Devices
Conditions
Position
1
Floppy Drive
1-inch Low Profile
Disk Drive
2
3
CD-ROM
DDS-Tape
1-inch Low Profile
Disk Drive
If a CD-ROM drive is installed, install
a 1.6-inch full height disk drive in this
position.
1.6-inch Full Height
Disk Drive
4
1-inch Low Profile
Disk Drive
This is the preferred position for a
1.6-inch full height disk drive.
1.6-inch Full Height
Disk Drive
If a CD-ROM drive is installed, a 1.6-
inch full height disk drive cannot be
installed in this position.
All hard disk drives are fast, wide SCSI devices. The CD-ROM drive and the
DDS tape drive are single-ended SCSI devices. The floppy drive is not a SCSI
device.
121
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing Your Workstation’s Hardware Configuration
Installing Storage Devices
Mounting the Storage Device Slides
From the accessory hardware kit which came with your workstation, locate
two plastic storage device slides. Using the screws that came with the stor-
age device, mount the slides on the new storage device so that the locking
tabs are at the connector end of the drive, as shown in Figure 22.
Locking Tab
Figure 22
Mounting the Storage Device Slides
CAUTION:
When mounting the storage device slides, only use the screws that shipped
with the storage device. Use of other screws can cause physical damage to
the device.
122
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing Your Workstation’s Hardware Configuration
Installing Storage Devices
Storage Device Cable Routing
When you install your storage device, be aware of the suggested cable rout-
ing paths as indicated in the cable routing label that is affixed to the top of
the storage tray.
Disk Shield
If you are installing a hard disk manufactured by Hewlett-Packard, you need
to install a disk shield.
1 Check the manufacturer’s labeling on the disk drive to determine if it is a
disk manufactured by Hewlett-Packard.
If the disk is not a Hewlett-Packard disk, skip the rest of this procedure.
2 From the accessory hardware kit which came with your workstation, lo-
cate the disk shield and four screws. See Figure 23.
3
Use the four screws to mount the disk shield on the drive, as shown in Figure 23.
Figure 23
Mounting the Disk Shield
123
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing Your Workstation’s Hardware Configuration
Installing Storage Devices
Removing the Disk Tray
Perform the following procedure to remove the Storage Tray from the sys-
tem unit:
1
2
Remove the storage tray retaining screw, as shown in Figure 24.
If installed, remove any locking device from the storage tray security loop on the
rear of the system unit.
3
Place your fingertips in the groove on the bottom of the storage tray bezel. See
Figure 24.
Retaining Screw
Figure 24
Removing the Storage Tray
4
Slide the storage tray completely out of the system unit.
CAUTION:
Be sure to support the storage tray from underneath while sliding it out of
the system unit.
Proceed to one of the following sections in this chapter to install your stor-
age device in the disk tray:
•
•
•
Installing a CD-ROM or a DDS-Format Tape Drive
Installing a Floppy Drive
Installing a Hard Disk Drive in Position 3 or Position 4
124
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing Your Workstation’s Hardware Configuration
Installing Storage Devices
Installing a CD-ROM or a DDS-Format Tape Drive
Perform the following procedure to install a CD-ROM or DDS tape drive in
the disk tray:
1
Remove the disk filler panel from the top location of the bezel by using a coin or
other flat, blunt, object to pry it from the front., as shown in Figure 25.
Figure 25
Removing a Disk Filler Panel
125
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing Your Workstation’s Hardware Configuration
Installing Storage Devices
2
From the rear of the storage tray, line up the disk slides on the CD-ROM or DDS
tape drive with the position 1slots in the storage tray chassis, and slide it into
place, as shown in Figure 26.
Figure 26
Installing a CD-ROM or DDS Tape
3
4
Push the storage device in until the locking tabs snap into place.
Connect the single-ended SCSI-2 data cable and the power cable to the drive.
Refer to the cable routing label on the storage tray.
5
Proceed to the section entitled Replacing the Storage Tray.
126
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing Your Workstation’s Hardware Configuration
Installing Storage Devices
Installing a Floppy Drive
Perform the following procedure to install a floppy drive in the disk tray:
1
Remove the disk filler panel from the bottom location of the bezel by using a coin
or other flat, blunt, object to pry it from the front, as shown in Figure 27.
Figure 27
Removing a Disk Filler Panel
2
Reach into the storage bay and locate the power and data cables for the floppy
drive.
Refer to the cable routing label on the storage tray. See Figure 28.
Connect the cables to the drive.
3
127
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing Your Workstation’s Hardware Configuration
Installing Storage Devices
4
From the front of the storage tray, line up the disk slides on the floppy drive with
the position 2 slots in the storage tray chassis and slide it into place, as shown in
Figure 28.
Cable Routing Label
Figure 28
Installing a Floppy Drive
5
Push the floppy drive in until the locking tabs snap into place.
Proceed to the section entitled Replacing the Storage Tray.
6
128
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing Your Workstation’s Hardware Configuration
Installing Storage Devices
Installing a Hard Disk Drive in Position 1
Perform the following procedure to install a hard disk drive:
1
Remove the disk filler panel from the bottom location of the bezel by using a coin
or other flat, blunt, object to pry it from the front, as shown in Figure 29.
Figure 29
Removing a Disk Filler Panel
2
Reach into the storage bay and locate the power and data cables for the disk drive.
Refer to the cable routing label on the storage tray. See Figure 30.
Connect the cables to the drive.
3
4
From the front of the storage tray, line up the disk slides on the hard disk drive
with the position 1 slots in the storage tray chassis and slide it into place, as shown
in Figure 30.
129
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing Your Workstation’s Hardware Configuration
Installing Storage Devices
Cable Routing Label
Figure 30
Installing a Hard Disk Drive in Position 1
5
6
7
Push the drive in until the locking tabs snap into place.
Snap the disk filler panel into the lower bezel position.
Proceed to the section entitled Replacing the Storage Tray.
130
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing Your Workstation’s Hardware Configuration
Installing Storage Devices
Installing a Hard Disk Drive in Position 3 or Position 4
Perform the following procedure to install a hard disk drive in positions 3 or
4 of the disk tray:
1
Remove the two retaining screws from the disk interconnect board, as shown in
Figure 31.
Figure 31
Removing the Disk Interconnect Board
2
Disconnect any cables from the disk interconnect board.
3
Hold the disk interconnect board on the edges and lift it straight up to remove it,
as shown in Figure 31.
131
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing Your Workstation’s Hardware Configuration
Installing Storage Devices
4
From the rear of the storage tray, line up the disk slides on the hard disk drive with
the position 3 or position 4 slots in the storage tray chassis and slide it into place,
as shown in Figure 32.
Cable Routing Label
Figure 32
Installing a Hard Disk Drive
5
6
Push the storage device in until the locking tabs snap into place.
Connect the fast, wide SCSI data cable and the power cable to the drive.
132
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing Your Workstation’s Hardware Configuration
Installing Storage Devices
7
Slide the disk interconnect board into the storage tray, as shown in Figure 33.
Figure 33
Installing the Disk Interconnect Board
8
Reconnect the human interface cable, and the disk drive data and power cables to
the disk interconnect board.
9
Replace the disk interconnect board retaining screws and tighten them firmly, as
shown in Figure 33.
10 Proceed to the section entitled “Replacing the Storage Tray.”
133
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing Your Workstation’s Hardware Configuration
Installing Storage Devices
Replacing the Storage Tray
1
Slide the storage tray assembly into the system unit chassis, as shown in Figure
34.
Retaining Screw
Figure 34
Installing the Storage Tray Assembly
2
Tighten the storage tray retaining screw, as shown in Figure 34.
3
Reconnect the power cords to the system unit, the monitor and any peripherals.
Connect the power cords to the ac wall outlets.
4
Power on any peripherals, the monitor, and the system unit.
134
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing Your Workstation’s Hardware Configuration
Installing Storage Devices
If you installed a new hard disk drive, proceed to the section entitled “Con-
figuring a Hard Disk Drive.”
If you installed a new removable media device, refer to the following chap-
ters for information on using the device:
•
•
•
Chapter 3 - Using Your CD-ROM Drive
Chapter 4 - Using Your Digital Data Storage (DDS) Tape Drive
Chapter 5 - Using Your 3.5-inch Floppy Drive
135
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing Your Workstation’s Hardware Configuration
Installing Storage Devices
Configuring a Hard Disk Drive
This section describes how to add a hard disk drive to your system as a file
system using SAM. If you installed a new hard disk drive, follow these
instructions to make your new disk usable as a file system. For more infor-
mation about configuring a hard disk drive, refer to the System Administra-
tion Tasks manual.
This procedure requires you to log in as root. If you cannot log in as root,
contact your system administrator.
1 Log in as root.
2 Move the mouse pointer to the arrow above the Toolbox control and click
the left mouse button.
Toolbox Control Arrow
3 The Toolbox subpanel opens. Click on the General toolbox icon, shown
below.
136
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing Your Workstation’s Hardware Configuration
Installing Storage Devices
4 A file manager window appears with a number of icons in it. Double-click
on the System_Admin toolbox icon.
5 Move the mouse cursor to the SAM icon shown below (your icon can look
like either of these) and double-click the left mouse button.
SAM (System Administration Manager) is a utility that performs system adminis-
tration tasks using a windows graphical user interface.
6 The System Administration Manager window opens. Double-click on
Peripheral Devices ->.
7 The Peripheral Devices window opens. Double-click on Disks and File
Systems ->.
8 The Disks and File Systems window opens. Double-click on CD-ROM,
Floppy, and Hard Disks.
The following screen message appears:
Scanning the system’s hardware...
The CD-ROM, Floppy, and Hard Disks window opens, containing a list of
drives currently configured on this system.
9
From the Actions menu, click on Add a Hard Disk Drive.
10 The Select a Disk to Add... window opens with a list of unused disks. Highlight
the hard disk drive you want to add to your system.
11 Click on OK.
137
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing Your Workstation’s Hardware Configuration
Installing Storage Devices
12 The Set Disk Usage and Options... window opens. Select File System and click
on OK.
13 The following screen messages appear:
Task started.
Creating the device file...
Modifying “/etc/checklist”...
Task completed.
Click on OK.
138
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing Your Workstation’s Hardware Configuration
Removing the Main Tray Assembly
Removing the Main Tray Assembly
Perform the following steps to remove the Main Tray Assembly:
1
Power off the system, the monitor, and any peripheral devices. Unplug the system
unit power cord and the power cord of any peripheral devices from ac wall out-
lets. Disconnect the power cord from the system unit.
NOTICE:
There is no need to manually shut down the HP-UX operating system on
your workstation before powering it off. When you turn off the power
switch, your workstation automatically shuts down the operating system
before terminating the power.
2
3
Disconnect cables from any peripheral devices.
Attach a static-grounding wrist strap to bare metal on the back panel of the system
unit.
4
Completely loosen the four captive screws on the rear of the system unit, as
shown in Figure 35.
Captive
Screws
Captive Screws
Figure 35
Removing Main Tray Assembly
139
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing Your Workstation’s Hardware Configuration
Removing the Main Tray Assembly
5
6
Place one hand on the top of the system unit and push, while pulling the handle
on the rear panel with your other hand. See Figure 35.
Slide the main tray assembly out of the chassis.
140
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing Your Workstation’s Hardware Configuration
Replacing the Main Tray Assembly
Replacing the Main Tray Assembly
Perform the following steps to replace the main tray assembly:
1
Align the main tray assembly with the chassis and slide it into place, as shown in
Figure 36.
Captive
Screws
Captive Screws
Figure 36
Replacing the Main Tray Assembly
2
Slide the main tray in until you feel it make contact with the internal connectors.
3
Push firmly and evenly on the main tray assembly to make sure that all connec-
tors are fully seated.
4
Tighten the four captive screws, as shown in Figure 36.
NOTICE:
To maintain FCC/EMI compliance, verify that the main tray is fully seated
and all four captive screws are completely tightened.
141
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing Your Workstation’s Hardware Configuration
Replacing the Main Tray Assembly
5 Reconnect the power cables and any other cables that you disconnected
when opening the workstation.
6 Power on the monitor, any peripheral devices, and the system unit.
142
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing Your Workstation’s Hardware Configuration
Installing Additional memory
Installing Additional memory
Take a moment to read over the following important notes about installing
memory.
•
Before you attempt to install additional memory modules in your C100/C110
workstation, use the procedure described in Appendix D, “Boot Console Inter-
face,” to determine the current memory configuration for this workstation.
•
•
•
Read over the steps involved in installing memory modules before you begin.
You must insert memory modules in pairs of equal size.
Modules must be inserted in the lowest numbered memory pair first then in nu-
merical order. For example, install memory in 0A and 0B first, then 1A and 1B,
2A and 2B, and 3A and 3B. Refer to Figure 37 for memory pair numbering and
location.
•
When you have finished installing additional memory modules, use the Boot
Console Interface to verify that they are seen by the workstation.
143
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing Your Workstation’s Hardware Configuration
Installing Additional memory
Table 15 shows the allowable memory configurations.
Table 15
C100/C110 Memory Configurations
Pair 0
Pair 1
Pair 2
Pair 3
Configuration
Number
Total
MB
A
B
A
B
A
B
A
B
1
2
16 16
-
-
-
-
-
-
-
-
-
-
-
-
32
16 16 16 16
64
3
16 16 16 16 16 16
96
4
16 16 16 16 16 16 16 16
128
128
160
192
224
256
288
320
384
416
512
5
64 64
-
-
-
-
-
-
-
-
-
-
-
-
6
64 64 16 16
7
64 64 16 16 16 16
8
64 64 16 16 16 16 16 16
9
64 64 64 64
-
-
-
-
-
-
10
11
12
13
14
64 64 64 64 16 16
64 64 64 64 16 16 16 16
64 64 64 64 64 64
-
-
64 64 64 64 64 64 16 16
64 64 64 64 64 64 64 64
144
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing Your Workstation’s Hardware Configuration
Installing Additional memory
Perform the following steps to add memory modules to your workstation.
1
Remove the main tray assembly according to the directions in “Removing the
Main Tray Assembly” earlier in this appendix.
2
Use Figure 37 to locate the memory modules on the CPU Assembly.
0A
2A
0B
2B
1A
3A
1B
3B
Rear of Main Tray
Figure 37
Memory Module Location
This workstation has 8 memory slots, labeled 0A, 0B through 3A, 3B. The mem-
ory configuration is 32 MB to 512 MB installed in pairs of 16 MB or 32 MB
memory modules.
Memory modules must be installed in pairs of equal capacity.
Always install the largest capacity memory modules in the lowest numbered
memory slots.
For example, if you have a pair of 16 MB memory modules and a pair of 64 MB
memory modules, first install the pair of 64 MB memory modules in slots 0A
and 0B, then install the 16 MB modules in slots 1A and 1B.
NOTICE:
Memory slots must be filled in order from 0A and 0B through 3A and 3B.
145
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing Your Workstation’s Hardware Configuration
Installing Additional memory
3
Close the ejector tabs on each side of the memory connector. See Figure 38.
Figure 38
Installing Memory Cards
4
Place the memory module in the connector, lining it up with the guides. Make
sure to put the notched end toward the left, as shown in Figure 38.
5
6
Press firmly and evenly on the memory module to ensure that it seats properly.
Replace the main tray assembly as described in “Replacing the Main Tray As-
sembly” earlier in this appendix.
To verify that this installation was successful, follow the steps in Appendix
D, “The Boot Console Interface,” on displaying memory information. If you
have only replaced a faulty memory module, you must issue the pdt clear
command in the service menu of the Boot Console Interface. Answer yes (y)
to the prompt “Continue? (Y/N) >.”
146
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing Your Workstation’s Hardware Configuration
Installing an EISA or GSC Option Board
Installing an EISA or GSC Option Board
Your workstation has 4 option slots. The top three are EISA/GSC slots and
the bottom one is GSC only.
NOTICES:
For optimum optional graphics board performance, we recommend that
you install graphics boards in slots 3 and 4 and not mix them with other
boards.
Dual graphics boards must be installed in slot 3 or slot 4 only.
Figure 39 shows the physical layout of the EISA/GSC slots.
Figure 39
EISA/GSC Slots from Outside the System Unit
147
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing Your Workstation’s Hardware Configuration
Installing an EISA or GSC Option Board
Graphics Paths
If you are installing a graphics option, read the information in this section
first.
graphics0 through graphics2 are not supported. If the configuration value is
set to “default” (graphics 0), the system console will be graphics 3, Slot 3.
graphics3 Graphics device in slot3. If there is a Dual Graphics Card in slot4,
this is the port to the right on the card when facing the back of the worksta-
tion.
graphics4 Graphics device in slot4. If there is a Dual Graphics Card in slot
3 or 4, this is the port to the left on the card when facing the back of the
workstation.
NOTICE:
If you install a VISUALIZE-48 graphics card (geometry accelerator board
installed in slot 3 or slot 4) the system path is graphics 3.
If your model C100/110 is running HPUX 9.05, the system console
graphics device must be installed in Slot 3.
If your model C100/110 is running HPUX 9.07 or later, the system will
find a console graphics device installed in Slot 3 by default. You may
install the console graphics device in Slot 4 if you modify your system files
as described in HP Visual User Environment Users Guide or HPUX X User
Environment User’s Guide.
148
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing Your Workstation’s Hardware Configuration
Installing an EISA or GSC Option Board
Installing the Option Board
Follow these steps to install an EISA or GSC board into your workstation:
NOTICE:
You may not install any graphics cards in Slots 1 or 2.
1
2
Remove the main tray assembly as described in “Removing the Main Tray As-
sembly” earlier in this appendix.
Press the fan release clip and rotate the fan, as shown in Figure 41.
Figure 40
Rotating the Fan
3
Remove the screw from the EISA retainer, and remove the EISA retainer, as
shown in Figure 41.
EISA Retainer
Figure 41
Removing the EISA Retainer
149
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing Your Workstation’s Hardware Configuration
Installing an EISA or GSC Option Board
4
5
Remove the EISA Slider, as shown in Figure 42.
In the desired EISA slot, turn the blank plate’s locking knob counter-clockwise
to unlock the plate, as shown in Figure 42.
Locking Knob
Blank Plate
EISA Slider
Figure 42
Removing the EISA Slider and Blank Plate
Remove the blank plate from the slot, as shown in Figure 42.
6
150
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing Your Workstation’s Hardware Configuration
Installing an EISA or GSC Option Board
7
Slide the board into the slot. Make sure that the hole in the board’s handle aligns
with the pin on the back panel, as shown in Figure 43.
Figure 43
Installing an Option Board
8
Press in firmly on both ends of the option board at the same time to make sure
that it is firmly seated in the backplane connector.
151
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing Your Workstation’s Hardware Configuration
Installing an EISA or GSC Option Board
9
Replace the EISA retainer and its screw, as shown in Figure 44.
Figure 44
Installing the EISA Retainer and EISA Slider
10 Replace the EISA slider, as shown in Figure 44.
152
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing Your Workstation’s Hardware Configuration
Installing an EISA or GSC Option Board
11 Rotate the fan back into place. Push it into the rear panel firmly until the clip
snaps into place, as shown in Figure 45.
Figure 45
Securing the Fan
12 Replace the main tray assembly as described in “Replacing the Main Tray As-
sembly” earlier in this appendix.
153
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing Your Workstation’s Hardware Configuration
Replacing the Battery
Replacing the Battery
1
2
3
Remove the main tray as described in Removing the Main Tray Assembly
earlier in this chapter.
Note the orientation of the battery. Make sure that you put the new battery in
place with the positive (+) side facing in the same direction.
Lift the clip and slip the battery out of its holder, as shown in Figure 42.
Figure 46
Removing the Battery
4
Insert the new battery in the same orientation as the old one. (Only use HP part
number 1420-0314 or equivalent.)
NOTICE:
If you cannot gain access to the battery, you may need to remove an option
board. Refer to Installing an EISA or GSC Option Board earlier in this
chapter for information on accessing the option boards.
CAUTION:
Danger of explosion if battery is incorrectly replaced. Replace only with
the same or equivalent type recommended by the manufacturer.
ATTENTION:
Il y a danger d’explosion s’il y a remplacement incorrect de la batterie.
Remplacer uniquement avec une batterie du même type ou d’un type
recommandé par le constructeur. Mettre au rébut les batteries usagées
conformément aux instructions du fabricant.
5
Follow the instructions in Replacing the Main Tray Assembly earlier in this chap-
ter to close and restart the system.
154
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing Your Workstation’s Hardware Configuration
Changing Your Monitor Type
Changing Your Monitor Type
Your system ships from the factory preset to use a monitor with a specific
resolution and frequency. If you replace your monitor with a different type,
you must reconfigure your workstation to support it.
There are two ways to reconfigure your workstation to support a different
monitor type:
Setting the Monitor Type from the Boot Console Interface
To change your workstation’s graphics parameters before you replace your
monitor, go to “Displaying and Setting the Monitor Type” in Appendix D.
Setting the Monitor Type at Power On
If you replace your workstation’s monitor with a different monitor type, and
do not set the workstation’s graphics parameters by using the monitor com-
mand before doing so, you need to perform the following:
If your keyboard connects to the PS/2 connector on your system, wait 2 sec-
onds after the Num Lock light flashes near the end of the boot sequence,
then press Tab to initiate the automatic monitor selection process.
If you have a keyboard that connects to the HIL connector on your system,
press Tab every three seconds during the boot sequence to initiate the auto-
matic monitor selection process.
Your system queries you for the new monitor type. Select the new type by
pressing Enter. The system queries you to confirm your selection. Press y to
save this monitor type.
If you don’t press y, the system stops cycling. You can use the monitor
graphics command in the configuration menu to change monitor type.
155
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing Your Workstation’s Hardware Configuration
Changing Your Monitor Type
156
Download from Www.Somanuals.com. All Manuals Search And Download.
C
SCSI Connections
157
Download from Www.Somanuals.com. All Manuals Search And Download.
SCSI Connections
This appendix provides information about connecting Small Computer Sys-
tem Interface (SCSI) devices to an HP 9000 C100/C110 workstation. It pre-
sents the information in the following sections:
•
•
•
•
•
SCSI bus differences
SCSI restrictions
Determining SCSI bus length
Assigning SCSI device IDs
Connecting to the SCSI ports
The instructions in this chapter assume you are using HP-UX version 9.05 or
later operating system with HP VUE version 3.0 or later interface.
NOTICE
When attaching external SCSI devices, be sure to terminate the last device
on the external SCSI bus.
158
Download from Www.Somanuals.com. All Manuals Search And Download.
SCSI Connections
SCSI Bus Differences
SCSI Bus Differences
A Small Computer Systems Interface (SCSI) bus is an IEEE standard bus for
connecting your workstation to internal and external devices (SCSI devices)
running at different speeds, singly or in combination. Examples of these
SCSI devices are 4-mm DDS-format tape drives, CD-ROM drives, and Win-
chester hard disk drives.
There are two types of SCSI buses available with this workstation - a single-
ended SCSI bus, and a fast, wide differential SCSI bus. Table 16 shows the
specification differences between these SCSI buses, and Table 17 shows the
SCSI addresses, ID numbers, and arbitration priorities for each.
CAUTION:
Do not mix single-ended and fast, wide devices on any one bus type. Doing this will
cause a system failure.
Table 16
SCSI Bus Differences
Device
Physical
Location
Controller
Embedded
or Plugable
Data Bus
Width
Maximum
Addresses* Cable Length
Maximum
Transfer Rate
Single-Ended
8 bits
8
6.0 meters
(19.6 feet)
Internal and Embedded
external
Up to 5 Mbytes
per second
Fast, Wide
Differential
16 bits
16
25 meters
(82 feet)
Internal
and
external
Embedded
Up to 20 Mbytes
per second
* Address 7 is reserved for host controller use on both buses.
159
Download from Www.Somanuals.com. All Manuals Search And Download.
SCSI Connections
SCSI Bus Differences
Table 17
SCSI Bus Addresses, ID Numbers, and Arbitration Priorities
SCSI ID Number
SCSI-2
Address
Priority
15 . . . . . . 8
7 . . . . . . 0
7
6
. . . . . . . .
. . . . . . . .
. . . . . . . .
. . . . . . . .
. . . . . . . .
. . . . . . . .
. . . . . . . .
. . . . . . . .
1 . . . . . . .
. 1 . . . . . .
. . 1 . . . . .
. . . 1 . . . .
. . . . 1 . . .
. . . . . 1 . .
. . . . . . 1 .
. . . . . . . 1
1 . . . . . . .
. 1 . . . . . .
. . 1 . . . . .
. . . 1 . . . .
. . . . 1 . . .
. . . . . 1 . .
. . . . . . 1 .
. . . . . . . 1
. . . . . . . .
. . . . . . . .
. . . . . . . .
. . . . . . . .
. . . . . . . .
. . . . . . . .
. . . . . . . .
. . . . . . . .
1
2
5
3
4
4
3
5
2
6
1
7
0
8
15
14
13
12
11
10
9
9
10
11
12
13
14
15
16
8
160
Download from Www.Somanuals.com. All Manuals Search And Download.
SCSI Connections
SCSI Restrictions
SCSI Restrictions
This section describes the SCSI restrictions that apply to your workstation in
the following areas:
•
•
•
Cables
Connectors and Terminator
SCSI configuration constraints
Cables
All SCSI devices ship without cables. Only SCSI cables approved by HP
can be used to connect your workstation and any SCSI devices. HP offers
the following SCSI cables for single-ended standard SCSI devices:
•
•
K2296 cable with 0.9 meter (3 feet) length
K2297 cable with 1.5 meter (5 feet) length
HP offers the following SCSI cables for connecting externally connected
devices to the system fast, wide port:
•
•
•
•
C2911A cable with 0.9 meter (3 feet) length
C2924A cable with 2.5 meter (8.2 feet) length
C2925A cable with 10.0 meter (32.8 feet) length
C2926A cable with 20.0 meter (65.6 feet) length
CAUTION:
SCSI cables approved by HP are designed to function within the SCSI tolerances for
HP devices. Use of other cables can result in significant problems with system
operation.
Singled-ended SCSI-2 definition limits the total cable length of SCSI-2
cables to 6 meters (19.6 feet).
Fast, wide differential SCSI definition limits the total cable length of Fast,
Wide SCSI cables to 25 meters (82 feet).
Always use the shortest possible cable(s) for your configuration.
161
Download from Www.Somanuals.com. All Manuals Search And Download.
SCSI Connections
SCSI Restrictions
If you are daisy-chaining single-ended standard SCSI-2 devices together,
use the following cables:
•
•
•
92222A cable with 0.5 meter (1.6 feet) length
92222B cable with 1.0 meter (3.2 feet) length
92222C cable with 2.0 meter (6.6 feet) length
If you are daisy-chaining fast, wide differential SCSI devices together, use
the following cables:
•
•
•
•
C2911A cable with 0.9 meter (3 feet) length
C2924A cable with 2.5 meter (8.2 feet) length
C2925A cable with 10.0 meter (32.8 feet) length
C2926A cable with 20.0 meter (65.6 feet) length
NOTICE
See “Determining SCSI Bus Length” later in this Appendix to determine
the total length of your cables.
Connectors and Terminators
Any standard single-ended SCSI device connecting to the system board
must use a 50-pin high-density thumb screw connector on the end connect-
ing to the system board.
Any fast, wide differential SCSI device connecting to the system board must
use a 68-pin high-density thumb screw connector on both ends.
It is not necessary to put a terminator on empty SCSI connectors on the back
panel. However, a SCSI device attached to the SCSI bus or the last device
connected to the SCSI bus must be terminated with a SCSI terminator. All of
the devices listed ship without terminators. If you do not already have a
SCSI terminator, you must order terminator C2904A (for 50-pin connectors)
or C2905A (for 68-pin connectors) from Hewlett-Packard.
SCSI Configuration Constraints
You are limited to the number of same-type SCSI devices per system. Before
adding another SCSI device, determine if the system can support the addi-
tional device.
162
Download from Www.Somanuals.com. All Manuals Search And Download.
SCSI Connections
SCSI Restrictions
This workstation offers the following types of SCSI bus, each with its own
configuration constraints:
•
•
single-ended standard SCSI-2 bus
fast, wide, differential SCSI bus
Single-Ended SCSI-2 Bus Configuration Constraints
For the single-ended standard SCSI-2 bus, HP-UX supports only one of each
type of removable disk drive and two of the same type tape devices per sys-
tem. Table 18 shows configuration constraints for each single-ended stan-
dard SCSI-2 device type. If the system has internal hard disk drives or a CD-
ROM drive, you must count them as SCSI-2 devices.
Table 18
Single-Ended SCSI-2 Bus Configuration Constraints
Maximum Number of Each
Single-Ended SCSI-2 Devices
Type of Device Allowed
Hard Disk Drives (external only)
7
1
2
2
1
1
7
CD-ROM Drives
4-mm DDS Tape Drives (one internal)
9-track Tape Drives
650-MB Magneto-Optical Drives
Magneto-Optical Autochangers (see notice below)
Maximum Number of SCSI-2 Devices
NOTICE: Magneto-Optical Autochangers use three SCSI-2 drive address. Each address
must be accounted for in the maximum number of SCSI-2 devices allowed.
CAUTION:
Do not mix single-ended standard and fast, wide SCSI-2 peripherals.
Fast, Wide Differential SCSI Bus Configuration Constraints
Fast, wide SCSI does not work with the single-ended standard SCSI-2.
Table 19 shows the configuration constraints for each fast, wide, differential
SCSI device type.
163
Download from Www.Somanuals.com. All Manuals Search And Download.
SCSI Connections
SCSI Restrictions
Table 19
Fast, Wide Differential SCSI Bus Configuration Constraints
Maximum Number of Each Type
External Fast, Wide SCSI Devices
of Device Allowed
Fats, Wide SCSI Drive (fast, wide disk drives
only)
15
Fast, Wide SCSI Disk Arrays (addressed as single
drive)
7
CAUTION:
Do not mix single-ended, fast differential, and fast, wide SCSI peripherals together
on the same bus.
164
Download from Www.Somanuals.com. All Manuals Search And Download.
SCSI Connections
Determining SCSI Bus Length
Determining SCSI Bus Length
This section helps you to determine the total length of the single-ended stan-
dard SCSI-2 bus and the fast, wide SCSI bus.
Single-Ended SCSI-2 Bus Length
Follow these instructions to calculate your total single-ended standard SCSI-
2 bus length (including the system unit, external SCSI-2 devices, and SCSI-
2 interconnect cables) using Table 20:
1
Find all of your external SCSI-2 devices in the first column. In the third column,
write the SCSI-2 bus lengths (from the second column) that correspond to your
devices.
NOTICE
In the third column, the length for the System Unit is already listed. This
number must always be used for the system unit.
2
In the fourth column, write down the lengths of the SCSI-2 interconnect cables
you are using for your installation. (Cable lengths are listed in subsection
“Cables” in the section on “SCSI Restrictions.”
3
4
Add all of the numbers in the third column and write that number on the subtotal
line at the bottom of the column. Do the same for the fourth column.
Add the subtotals together and write the total in the Total SCSI-2 Bus Length box.
NOTICE
The total length of the single-ended standard SCSI-2 bus must not exceed 6
meters (19.6 feet). If the number you write for Total SCSI-2 Bus Length is
greater than 6 meters (19.6 feet), try configuring your installation with
shorter cables.
If you have problems, call your designated service representative.
165
Download from Www.Somanuals.com. All Manuals Search And Download.
SCSI Connections
Determining SCSI Bus Length
Table 20
Bus Length Worksheet for Single-Ended SCSI Bus
External
Cable Length
meters (feet)
Internal SCSI-2 Bus Length
meters (feet)
Device Internal Length
meters (feet)
SCSI-2 Device
System Unit
A2655A
C1520B
C1521B
C1700C
C1701C
C1704C
C1705C
C2213A
C2217T
1.5 (4.9)
0.3 (1.0)
0.2 (0.7)
0.2 (0.7)
1.1 (3.6)
0.3 (1.0)
0.0 (0.0)
0.0 (0.0)
1.5 (4.9)
1.3 (4.3)
1.5
(4.9)
N/A
Subtotals:
__________
+ __________
Total SCSI-2 Bus Length
= __________
(Total single-ended SCSI bus length not to exceed 6 meters [19.6 feet])
166
Download from Www.Somanuals.com. All Manuals Search And Download.
SCSI Connections
Determining SCSI Bus Length
Fast, Wide Differential SCSI Bus Length
Follow these instructions to calculate your total bus length for the fast, wide
SCSI bus on your system, using Table 21.
1
2
List all of your internal Fast, Wide SCSI devices in the first column.
In the third column, write the lengths of the internal Fast, Wide SCSI bus that cor-
respond to your devices.
3
In the fourth column, write down the lengths of the Fast, Wide SCSI interconnect
cables you are using for your installation. (Cable lengths are listed in subsection
“Cables” in the section on “SCSI Restrictions.”)
4
5
Add all of the numbers in the third column and write the sum on the subtotal line
at the bottom of the column. Do the same for the fourth column.
Add the subtotals together and write the total on the Total Fast, Wide SCSI Bus
Length line.
NOTICE:
The total length of the Fast, Wide SCSI bus must not exceed 25 meters (82
feet). If the number you write for Total Fast, Wide SCSI Bus Length is
greater than 25 meters, try configuring your installation with shorter cables.
If you have problems, call your designated service representative.
Table 21
Fats, Wide SCSI Bus Length Worksheet for Fast, Wide Differential SCSI Bus
External
Fats, Wide
Device
Internal Fats, Wide SCSI Bus
Length meters(feet)
Device Internal Length
meters(feet)
Cable
Length
meters(feet)
System Unit
C3034T
1.5 (4.9)
1.0 (3.3)
1.0 (3.3)
1.0 (3.3)
N/A
C3035T
C3036T
Subtotals: ______________
+ ________
Total Fast, Wide SCSI Bus Length = ______________
(Total fast, wide SCSI bus length not to exceed total of 25 meters [82 feet])
167
Download from Www.Somanuals.com. All Manuals Search And Download.
SCSI Connections
Assigning SCSI Device IDs
Assigning SCSI Device IDs
Before assigning a SCSI device ID to your drive, you need to check your
existing SCSI device IDs. To determine which SCSI device IDs are available
for your device, use the ioscan command in a terminal window:
1
Click on the Terminal Control on the Front Panel of your Workspace.
Terminal Control
A terminal window opens.
2
3
Move the mouse cursor into the terminal window and single-click the left mouse
button.
If you are using HP-UX 9.05 or greater, enter the following at the prompt
/etc/ioscan -d scsi
After a few moments the ioscan utility lists all of the SCSI I/O devices it could
find. The list should appear similar to the following:
H/W Path
=====================================
2.0.1.2.0 cd-rom_drive ok(nnnnnnnn)
Description
Status
168
Download from Www.Somanuals.com. All Manuals Search And Download.
SCSI Connections
Assigning SCSI Device IDs
If you are using HP-UX 10.0, enter the following at the prompt:
/usr/sbin/ioscan -f
After a few moments, the ioscan utility lists all of the SCSI I/O devices it could
find. The list appears similar to the following:
Class
I H/W Path
Driver
S/W State H/W Type
Description
================================================================================
bc
0
root
ccio
c720
tgt
CLAIMED
CLAIMED
CLAIMED
CLAIMED
CLAIMED
CLAIMED
CLAIMED
CLAIMED
CLAIMED
BUS_
NEXUS
bc
1 8
BUS_NEXUS I/O Adapter
INTERFACE GSC built-in Fast/Wide SCSI
DEVICE
ext_bus
target
disk
0 8/12
0 8/12.0
3 8/12.0.0
1 8/12.5
2 8/12.5.0
2 8/12.6
0 8/12.6.0
0 8/16
sdisk
tgt
DEVICE
DEVICE
DEVICE
DEVICE
DEVICE
QUANTUM LPS1080WD
target
disk
sdisk
tgt
DEC
DEC
DSP3210SW
DSP3210SW
target
disk
sdisk
ba
bus_adapter CLAIMED
BUS_NEXUS Core I/O Adapter
INTERFACE Built-in Parallel Interface
INTERFACE Built-in Audio
INTERFACE Built-in RS-232C
INTERFACE Built-in SCSI
DEVICE
ext_bus
audio
tty
2 8/16/0
0 8/16/1
0 8/16/4
1 8/16/5
3 8/16/5.2
1 8/16/5.2.0
4 8/16/5.3
0 8/16/5.3.0
5 8/16/5.4
10 8/16/5.4.0
6 8/16/5.6
5 8/16/5.6.0
0 8/16/6
0 8/16/7
2 10
CentIf
audio
asio0
c700
tgt
CLAIMED
CLAIMED
CLAIMED
CLAIMED
CLAIMED
CLAIMED
CLAIMED
CLAIMED
CLAIMED
CLAIMED
CLAIMED
CLAIMED
CLAIMED
CLAIMED
CLAIMED
CLAIMED
CLAIMED
CLAIMED
CLAIMED
ext_bus
target
disk
sdisk
tgt
DEVICE
DEVICE
DEVICE
DEVICE
DEVICE
DEVICE
DEVICE
TOSHIBA CD-ROM XM-4101TA
target
tape
stape
tgt
HP
HP35480A
target
disk
sdisk
tgt
SEAGATE ST3600N
MICROP 2112
target
disk
sdisk
lan2
ps2
lan
INTERFACE Built-in LAN
INTERFACE Built-in Keyboard/Mouse
BUS_NEXUS I/O Adapter
INTERFACE GSC add on Fast/Wide SCSI
DEVICE
ps2
bc
ccio
c720
tgt
ext_bus
target
disk
3 10/12
7 10/12.4
6 10/12.4.0
sdisk
graph3
DEVICE
SEAGATE ST31200W
graphics 2 10/16
INTERFACE Graphics
BUS_NEXUS Core I/O Adapter
INTERFACE Built-in HIL
INTERFACE Built-in RS-232C
BUS_NEXUS EISA Bus Adapter
INTERFACE EISA card HWP0C70
DEVICE
ba
1 10/20
bus_adapter CLAIMED
hil
0 10/20/1
hil
CLAIMED
CLAIMED
CLAIMED
CLAIMED
CLAIMED
CLAIMED
CLAIMED
CLAIMED
CLAIMED
tty
1 10/20/2
asio0
eisa
ba
2 10/20/5
ext_bus
target
target
target
4 10/20/5/3
8 10/20/5/3.0
9 10/20/5/3.1
10 10/20/5/3.2
hshpib
tgt
tgt
DEVICE
tgt
DEVICE
processor 0 32
memory 0 49
processor
memory
PROCESSOR Processor
MEMORY
Memory
169
Download from Www.Somanuals.com. All Manuals Search And Download.
SCSI Connections
Assigning SCSI Device IDs
4
If you are using HP-UX 9.05 or greater, you can which SCSI IDs are currently in
use by looking under the H/W Path heading. The listing 2.0.1 scsi is the built-in
SCSI bus controller. For devices connected to the built-in SCSI bus, such as
disks, the fourth number is the SCSI ID for that device. For example, the listing
2.0.1.6.0 in the sample device list tells you that there is a SCSI device (a disk)
currently using ID 6 on the SCSI bus.
Although the information is presented in a different format if you are using HP-
UX 10.0, you look under the H/W Path heading also.
Single-Ended Standard System SCSI Device IDs
Before assigning a SCSI device ID to your drive, you need to check your
SCSI device IDs. To check what SCSI device IDs are available and assign an
ID to your device, follow these instructions which use Table 22:
1
2
Write in the SCSI device ID of any internal drives in Table 22
Write in the type of external drives (single-ended standard, EISA, or fast, wide
devices) currently connected to your system under the heading “External Device
Drives” and each drive’s SCSI device ID under the heading “Device ID.”
3
Add your new drive to the table if it is an external device. If it is an internal drive,
continue to Step 4.
NOTICE:
The C1700A Magneto-Optical Autochanger uses three SCSI addresses,
and accounts for three of the seven devices allowed on the SCSI bus.
4
Check to see which SCSI device IDs are not used. You can use ID numbers 0
through 6 if they are not already in use. If the default ID on your drive does not
conflict with any existing drive IDs, use that ID. If your default address conflicts
with an existing drive ID, you need to assign a new SCSI device ID to your drive.
See the drive installation documentation for information on changing the device
ID.
CAUTION:
Do not use SCSI device ID 7 for any device. It is reserved for the built-in SCSI bus
controller
170
Download from Www.Somanuals.com. All Manuals Search And Download.
SCSI Connections
Assigning SCSI Device IDs
Table 22
Single-Ended SCSI Device IDs
SCSI Device Drives
Device ID (Address) Number
(Only 0 through 6 Available)
Internal External
Internal System Drives:
System SCSI Drive(s)
CD-ROM Drive (if present, uses ID No.2)
__________ N/A
__________ N/A
4-mm DDS Tape Drive
(if present, uses ID No.1)
External Device Drives
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
__________
__________
__________
__________
__________
__________
__________
__________
1st External Device
2nd External Device
3rd External Device
4th External Device
5th External Device
6th External Device
7th External Device
__________________
__________________
__________________
__________________
__________________
__________________
__________________
NOTICE: You can have no more than 7 single-ended SCSI devices (internal and ex-
ternal) connected to the system.
5
6
Write in the SCSI device ID of any internal drives in Table 22.
Write in the type of external single-ended drives currently connected to your
workstation under the heading “External Device Drives” and each drive’s SCSI
device ID under the heading “Device ID.”
7
Add your new drive to the table if it is an external device. If it is an internal drive,
continue to Step 8.
NOTICE:
The C1700A Magneto-Optical Autochanger uses three SCSI IDs, and
accounts for three of the seven devices allowed on the SCSI bus
171
Download from Www.Somanuals.com. All Manuals Search And Download.
SCSI Connections
Assigning SCSI Device IDs
8
Check to see which SCSI device IDs are not used. You may use ID numbers 0
through 6 if they are not already in use. If the default ID on your drive does not
conflict with any existing drive IDs, use that ID. If your default address conflicts
with an existing drive ID, you need to assign a new SCSI device ID to your drive.
Refer to the drive’s installation documentation for information on changing the
device ID.
CAUTION:
Do not use SCSI device ID 7 for any device. It is reserved for the built-in SCSI bus
controller.
Fast, Wide Differential SCSI IDs
Before assigning a SCSI device ID to your drive, you need to check your
SCSI device IDs. To check which SCSI device IDs are available and assign
an ID to your device, follow these instructions which use Table 23.
1
Write in the type of internal drives currently connected to your system under the
heading “Fast, Wide Differential SCSI Device Drives” and each drive’s SCSI de-
vice ID under the heading “Device ID.”
2
3
Add your new drive to the table.
Check to see what SCSI device IDs are not used. You may use ID numbers 0
through 6 and 8 through 15 if they are not already in use. If the default ID on your
drive does not conflict with any existing drive IDs, use that ID. If your default
address conflicts with an existing drive ID, assign a new fast, wide differential
SCSI device ID to your drive. Refer to the drive’s installation documentation for
information on changing the device ID.
CAUTION:
Do not use SCSI device ID 7 for any device.
Table 23
Fast, Wide Differential SCSI Device Drives and Device ID
Device ID (Address) Number
Fast, Wide Differential SCSI Device Drives
(ID 7 not available)
1st Internal Device
2nd Internal Device
______________________________
______________________________
6
5
NOTICE: You can have no more than 15 SCSI devices connected to a fast, wide bus.
172
Download from Www.Somanuals.com. All Manuals Search And Download.
SCSI Connections
Connecting to the SCSI Ports
Connecting to the SCSI Ports
This section describes how to connect to the system SCSI ports (single-
ended and fast, wide).
System SCSI Port Connection
The system contains two (2) SCSI connectors:
•
•
System Single-Ended SCSI Connector
System Fast, Wide SCSI Connector
Figure 47 shows the two SCSI connectors. SCSI cables connect to these
ports with a high-density thumb screw connector.
Single-ended SCSI
Fast, Wide SCSI
Figure 47
Rear Panel SCSI Connectors without Terminators
NOTICE:
It is not necessary to put a terminator on empty SCSI connectors on
the backpanel. However, the last device connected to the SCSI bus
must be terminated with a SCSI terminator. All of the devices listed
ship without terminators. If you do not already have a SCSI
terminator, you must order a C2905A, 68-pin terminator for the fast,
wide SCSI bus, or a C2904A, 50-pin high density terminator for the
single-ended SCSI bus from Hewlett-Packard.
173
Download from Www.Somanuals.com. All Manuals Search And Download.
SCSI Connections
Connecting to the SCSI Ports
174
Download from Www.Somanuals.com. All Manuals Search And Download.
D
The Boot Console Interface
175
Download from Www.Somanuals.com. All Manuals Search And Download.
The Boot Console Interface
This appendix describes the different features of the boot console interface
and how to use them. It presents the information in the following sections:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Boot console interface features
Accessing the boot console interface
Booting your workstation
Searching for bootable media
Resetting your workstation
Displaying and setting paths
Displaying and setting the monitor type
Displaying the current memory configuration
Displaying the status of the EISA slots
Setting the Auto Boot and Auto Search flags
Displaying and setting the Fastboot mode
Displaying the LAN station address
Displaying system information
Displaying PIM information
The instructions in this chapter assume you are using HP-UX version 9.05 or
later operating system.
176
Download from Www.Somanuals.com. All Manuals Search And Download.
The Boot Console Interface
Boot Console Interface Features
Boot Console Interface Features
There are times when you want to interact directly with the hardware of your
workstation before it boots the operating system. Your workstation provides
a menu-driven boot console interface that allows you to perform special
tasks, display information, and set certain system parameters, even if the
operating system is unavailable.
Here are some of the things you can do:
•
•
•
•
•
•
•
•
•
•
•
•
Boot your workstation
Search for bootable media
Reset your workstation
Display and set boot paths
Display and set your monitor type
Display memory configuration information
Display the status of the EISA slots
Set Auto Boot and Auto Search
Set Fastboot
Display LAN information
Display system information
Display PIM information
NOTICE:
All of the tasks in the boot console interface should be performed by a
system administrator.
The boot console menus follow, showing the various tasks you can perform
and the information available.
The shortened version of all commands is indicated by the uppercase letters.
Help is available for all the menus and commands by using either help, he,
or ? and the menu or command you want help on.
177
Download from Www.Somanuals.com. All Manuals Search And Download.
The Boot Console Interface
Boot Console Interface Features
------ Main Menu -----------------------------------------------------
Command
Description
-------
-----------
BOot [PRI|ALT|<path>]
PAth [PRI|ALT|CON|KEY][<path>]
SEArch [DIsplay|IPL] [<path>]
COnfiguration menu
INformation menu
SERvice menu
Boot from specified path
Display or modify a path
Search for boot devices
Displays or sets boot values
Displays hardware information
Displays service commands
Redisplay the current menu
Display help for menu or command
Restart the system
DIsplay
HElp [<menu>|<command>]
RESET
------
Main Menu: Enter a command or a menu >
------ Configuration Menu --------------------------------------------
Command
Description
-------
-----------
AUto [BOot|SEArch] [ON|OFF]
BootInfo
Display or set specified flag
Display boot-related info
Set system to predefined values
Display or set boot tests execution
Display Core LAN station address
Display or set monitor type in EEPROM
DEfault
FastBoot [ON|OFF]
LanAddress [<option>]
MOnitor [<option>]
PAth [PRI|ALT|CON|KEY] [<path>] Display or modify a path
PRocessor [<proc>] [ON|OFF]
SEArch [DIsplay|IPL] [<path>]
TIme [c:y:m:d:h:m:[s]
BOot [PRI|ALT|<path>]
DIsplay
Config/Deconfig processor
Search for boot devices
Read or set real time clock in GMT
Boot from specified path
Redisplay the current menu
Display help for menu or command
Restart the system
HElp [<command>]
RESET
MAin
Return to Main Menu
------
Configuration Menu: Enter a command or a menu >
178
Download from Www.Somanuals.com. All Manuals Search And Download.
The Boot Console Interface
Boot Console Interface Features
------ Information Menu ----------------------------------------------
Command
-----------
ALL
Description
-----------
Display all system information
Display boot-related information
Display cache information
Display coprocessor information
Display EISA slot information
Display firmware version
Display memory information
Display monitor type in EEPROM
Display processor information
BootInfo
CAche
COprocessor
EIsa
FWrVersion
MEmory
MOnitor
PRocessor
BOot [PRI|ALT|<path>] Boot from specified path
DIsplay
HElp [<command>]
RESET
Redisplay the current menu
Display help for menu or command
Restart the system
MAin
Return to Main Menu
------
Information Menu: Enter a command or a menu >
------ Service Menu --------------------------------------------------
Command
Description
-------
-----------
MemRead <address> [<len>]
PIM [<proc>][HPMC|LPMC|TOC]
PDT [CLEAR]
Read memory and I/O locations
Display PIM information
Display or clear the Page Deallocation
Table
ChassisCodes [<proc>]
BOot [PRI|ALT|<path>]
DIsplay
Display chassis codes
Boot from specified path
Redisplay the current menu
Display help for menu or command
Restart the system
HElp [<command>]
RESET
MAin
Return to Main Menu
------
Service Menu: Enter a command or a menu >
179
Download from Www.Somanuals.com. All Manuals Search And Download.
The Boot Console Interface
Accessing the Boot Console Interface
Accessing the Boot Console Interface
To access the boot console interface, follow these steps:
This procedure should be done by a system administrator.
NOTICE:
1
2
Close any files and applications on your workstation.
Press the power switch on the front panel of the system unit.
NOTICES:
There is no need to manually shut down the HP-UX operating system on
your workstation before powering it off. When you turn off the power
switch, your workstation automatically shuts down the operating system
before terminating the power.
Make sure that you do not unplug the system’s power cord or otherwise
interrupt power to the system unit at this time.
3
Power on your workstation.
If Autoboot is turned off, the boot sequence automatically stops at the boot
console Main Menu.
If Autoboot is turned on, you will see the following messages:
Processor is starting Autoboot process. To discontinue,
press any key within 10 seconds.
NOTICE:
If you are using a power-saving monitor, you will have less than 10
seconds from the time this message appears to press a key.
4
Press a key. You will then see the message:
Boot terminated
The Main Menu of the boot console appears.
180
Download from Www.Somanuals.com. All Manuals Search And Download.
The Boot Console Interface
Booting Your Workstation
Booting Your Workstation
Usually, you start your workstation by turning it on and waiting for HP-UX
to boot automatically. However, you may not always want the usual
sequence to occur.
For example, you may want to start your workstation from an operating sys-
tem that is stored on a device that is different from your usual boot device. If
your normal operating system kernel or the disk on which it resides becomes
damaged or unusable, you may wish to boot from a different disk or perhaps
another type of device, such as a DDS-format tape drive.
Here are some situations and examples:
•
If you know which device you want to boot from, and you know that it contains
a bootable operating system, follow the directions in “Accessing the Boot Con-
sole Interface” earlier in this appendix, and then type the following at the prompt:
Main Menu: Enter a command or a menu > boot device
where device is the hardware path to the device, specified in Mnemonic Style
Notation.
For example, if you wish to boot an operating system that is stored on a DDS-
format tape in a drive that is located at ‘‘scsi.1.0’’, follow the directions in
“Accessing the Boot Console Interface” earlier in this appendix, and then type
the following command at the prompt:
Main Menu: Enter a command or a menu > boot scsi.1.0
The operating system on the specified device is used to start your workstation.
•
If you wish to interact with the Initial System Loader (ISL) before booting your
workstation, follow the directions in “Accessing the Boot Console Interface” ear-
lier in this appendix, and then type the following at the prompt
Main Menu: Enter a command or a menu > boot device
You are prompted:
Interact with ISL (Y or N) >
181
Download from Www.Somanuals.com. All Manuals Search And Download.
The Boot Console Interface
Booting Your Workstation
Answering yes (y) causes the ISL to be loaded from the specified device. After a
short time, the following prompt appears on your screen:
ISL>
ISL is the program that actually controls the loading of the operating system. By
interacting with ISL, you can choose to load an alternate version of the HP-UX
operating system. If you do not want ISL to be loaded, you must enter NO.
For example, if the usual kernel (/hp-ux for 9.05, and /stand/vmunix for 10.0)
on your root disk (fwscsi.6.0) has become corrupted, and you wish to boot your
workstation from the backup kernel (/SYSBCKUP for 9.05, and /stand/vmu-
nix.prev for 10.0), type the following at the ISL>prompt:
ISL>hpux /SYSBCKUP (for 9.05)
ISL>hpux /stand/vmunix.prev (for 10.0)
•
If you do not know which media in your file systems have bootable oper-
ating systems, you can find them with the search IPL command.
182
Download from Www.Somanuals.com. All Manuals Search And Download.
The Boot Console Interface
Searching for Bootable Media
Searching for Bootable Media
To list devices that contain bootable media, follow the directions in “Access-
ing the Boot Console Interface” earlier in this appendix, and then type the
following at the prompt:
Main Menu: Enter a command or a menu > search ipl
The search command searches all buses. The search may turn up more
devices than there are lines on your display. If you are using a text terminal,
you may control the progress of the search from your terminal’s keyboard by
performing the following steps:
•
•
•
To hold the display temporarily, press Ctrl S
To continue the display, press Ctrl Q
To halt the search, press any other key
These flow-control commands do not work with a bitmapped display, but
such a display can show more than forty lines of text, so you are unlikely to
need them.
To search for devices of just one type that actually contain bootable media,
follow the directions in “Accessing the Boot Console Interface” earlier in
this appendix, and then type the following at the prompt:
Main Menu: Enter a command or a menu > search ipl device_type
Where device_type is one of the following:
fwscsi is the built-in fast, wide SCSI bus
scsi is the built-in single-ended SCSI bus
lan is all connections to the built-in LAN
slotn.fwscsi is an optional fast, wide SCSI interface in slot number n
183
Download from Www.Somanuals.com. All Manuals Search And Download.
The Boot Console Interface
Resetting Your Workstation
Resetting Your Workstation
To reset your workstation, follow the directions in “Accessing the Boot Con-
sole Interface” earlier in this appendix, and then type the following at the
prompt:
Main Menu: Enter a command or a menu > reset
To reset your workstation to its predefined values, follow the directions in
"Accessing the Boot Console Interface" earlier in this appendix, and then
type the following at the prompt to access the Configuration Menu:
Main Menu: Enter a command or a menu > co
When the Configuration Menu appears, type the following at the prompt:
Configuration Menu: Enter a command or a menu > default
184
Download from Www.Somanuals.com. All Manuals Search And Download.
The Boot Console Interface
Displaying and Setting Paths
Displaying and Setting Paths
A path is the hardware address of a device that is attached to the I/O system
of your workstation. The path command sets the system paths shown in
Table 24.
The path command sets and displays the hardware address of a specified
device attached to the I/O bus of your workstation.
Table 24
System Paths
Path Type
Device
primary or pri
Your workstation’s default boot device (usually the root
disk)
alternate or alt
console or con
Your workstation’s alternate boot device (usually a DDS-
format tape device)
Your workstation’s primary display device
keyboard or
Your workstation’s primary ASCII input device
key
To display the current settings for the system paths, type the following at the
prompt:
Main Menu: Enter a command or a menu > path
The paths are displayed in Mnemonic Style Notation, as shown in Table 25.
Table 25
Mnemonic Style Notation
I/O Type
Specification Format
Built-in FWSCSI
Built-in SCSI
Built-in LAN
core.fwsci.scsi_address.logical_unit_number
core.scsi.scsi_address.logical_unit_number
core.lan.server_address.init_timeout.io_timeout
185
Download from Www.Somanuals.com. All Manuals Search And Download.
The Boot Console Interface
Displaying and Setting Paths
To display the current setting for a particular system path, follow the direc-
tions in “Accessing the Boot Console Interface” earlier in this appendix, and
then type the following at the prompt:
Main Menu: Enter a command or a menu > path path_type
where path_type is one of the path types listed in Table 24.
For example, to get the path to the primary boot device, follow the directions
in “Accessing the Boot Console Interface” earlier in this chapter, and then
type the following at the prompt:
Main Menu: Enter a command or a menu > path primary
To set a system path to a new value, follow the directions in “Accessing the
Boot Console Interface” earlier in this chapter, and then type the following
at the prompt:
Main Menu: Enter a command or a menu > path path_type path
where path_type is one of the path types listed in Table 24 and path is the
specification of the path in Mnemonic Style Notation (as described in Table
25). For example, to set the primary boot path to a scsi disk with an ID of
6.0, follow the directions in “Accessing the Boot Console Interface” earlier
in this appendix, and then type the following at the prompt:
Main Menu: Enter a command or a menu > path pri scsi.6.0
186
Download from Www.Somanuals.com. All Manuals Search And Download.
The Boot Console Interface
Displaying and Setting the Monitor Type
Displaying and Setting the Monitor Type
Your system ships from the factory preset to use a monitor with a specific
resolution and frequency. If you replace your workstation’s monitor with a
different type of monitor, you must reconfigure your workstation to support
the new monitor.
The Monitor Command
The monitor command lets you change your workstation’s graphics config-
uration. This command is available in both the Information and Configura-
tion Menus of the boot console interface. However, when you use it in the
Information Menu, monitor displays only the current graphics and console
information. You must use monitor in the Configuration Menu to set a mon-
itor type.
NOTICE:
The monitor command lets you change your workstation’s graphics
configuration before you replace your monitor. For information
about changing the configuration after you replace your monitor, go
to the section “Changing Your Monitor Type” in Appendix B.
To display the current graphics and console information, enter the following
command;
monitor
The correct usage for setting the graphics configuration is:
monitor graphics_path
where valid graphics_path parameters are:
graphics3
Graphics device in slot3. If there is a Dual Color Graphics Card in slot4, this is
the console port to the right on the card when facing the back of the workstation.
graphics4
Graphics device in slot4. If there is a Dual Color Graphics Card in slot4, this is
the console port to the left on the card when facing the back of the workstation.
187
Download from Www.Somanuals.com. All Manuals Search And Download.
The Boot Console Interface
Displaying and Setting the Monitor Type
Displaying the Current Monitor Configuration
To display the current monitor configuration for your system from the Con-
figuration Menu of the boot console interface, follow the directions in
“Accessing the Boot Console Interface” earlier in this appendix. Once you
are in the Boot Console Interface Main Menu, type:
Main Menu: Enter a command or a menu > configuration
This places you in the Configuration Menu. From here type:
Configuration Menu: Enter command > monitor
The screen displays a list of the current monitors configured for your work-
station.
MONITOR INFORMATION
Slot #
HPA
State
----
Resolution
----------
Frequency
---------
Class
---------
graphics3
graphics4
-------
f4000000
f6000000
-------
Present Fixed
Empty
Current Console Path:
core.RS232_.9600.8.none
Stable Store Console Path:GRAPHICS3
In this example, the graphics cards are configured as follows:
•
•
Graphics slot3 - CRX48Z
Graphics slot4 - Empty
188
Download from Www.Somanuals.com. All Manuals Search And Download.
The Boot Console Interface
Displaying and Setting the Monitor Type
Setting the Monitor Type
Using the list in the example above, you can set the monitor type for graph-
ics slot3 by typing the following:
Configuration Menu: Enter command > monitor graphics3
NOTICE:
You can exit at this point by entering x, and the monitor type will not be
changed.
The screen displays the choice of supported monitors, similar to the follow-
ing. Follow the directions in the screen prompts and enter the monitor type
you want to configure (in this example, number 2).
MONITOR INFORMATION
Type Resolution
---- ----------
Frequency
---------
72Hz
1
1280x1024
1024x768
1024x768
1024x768
1280x1024
1024X768
640X480
2
75Hz
3
70Hz
4
75Hz Flat Panel
60Hz
5
6
60Hz
60Hz
7
8
1280X1024
1024X768
800X600
75Hz VESA
75Hz VESA
75Hz VESA
75Hz VESA
72HZ GrayScale
50HZ
9
10
11
12
13
640X480
1280X1024
1280X1024
Enter monitor type selection from list above (or ’x’ to exit): 2
1024x768 75Hz
2
Press <y> to save monitor type <x> to exit monitor selection: y
189
Download from Www.Somanuals.com. All Manuals Search And Download.
The Boot Console Interface
Displaying and Setting the Monitor Type
The MONITOR INFORMATION table reappears with the new monitor
shown in slot0.
MONITOR INFORMATION
Slot #
HPA
State
----
Resolution
----------
Frequency
---------
Class
---------
graphics3
graphics4
-------
f4000000
f6000000
-------
Present Fixed
Empty
Current Console Path:
core.RS232_.9600.8.none
Stable Store Console Path:GRAPHICS3
Trying to change the monitor type on a slot that cannot support that monitor
results in a warning, as shown in the following example:
Configuration Menu: Enter command > monitor graphics3
MONITOR INFORMATION
Reminder: SGIC only supports one type of monitor.
Changing its monitor type will not have any effect.
Slot #
HPA
State
----
Resolution
----------
Frequency
---------
Class
---------
graphics3
graphics4
-------
f4000000
f6000000
-------
Present Fixed
Empty
Current Console Path:
core.RS232_.9600.8.none
Stable Store Console Path:GRAPHICS3
190
Download from Www.Somanuals.com. All Manuals Search And Download.
The Boot Console Interface
Displaying and Setting the Monitor Type
Trying to change the monitor type on an empty slot, fails and gives you this
warning message:
Configuration Menu: Enter command > monitor graphics4
MONITOR INFORMATION
WARNING: Intended graphics hardware does not exist.
Be sure to install the hardware after you power down the system.
Slot #
HPA
State
----
Resolution
----------
Frequency
---------
Class
---------
graphics3
graphics4
-------
f4000000
f6000000
-------
Present Fixed
Empty
Current Console Path:
core.RS232_.9600.8.none
Stable Store Console Path:GRAPHICS3
Table 26 shows the possible combinations of graphics cards and slots.
Graphics 3, and Graphics 4 refer to the console paths, GRAPHICS3, and
GRAPHICS4, respectively. There is no GRAPHICS 1 or GRAPHICS 2
path. Configurations 6 and 7 use the GRAPHICS3 path even though the
Geometry Accelerator card is in slot 4.
The abbreviations in the table represent the following:
"S”, a color graphics or Hyperdrive series graphics card
"D”, a dual color graphics card
"V”, a VISUALIZE-48 graphics card
191
Download from Www.Somanuals.com. All Manuals Search And Download.
The Boot Console Interface
Displaying and Setting the Monitor Type
Table 26
Graphics Configurations
Confiig. Number Graphics 3 Graphics 4 Slot
Slot Slot
2
3
Slot
4
Number of Heads 10/16
10/20
1
1
2
3
4
5
6
7
1
1
2
2
2
1
1
Y
S
Y
Y
Y
Y
S
S
Y
Y
Y
Y
Y
S
D
D
V
V
NOTICE:
HPUX 9.05 requires path console graphics3.
Do not put a graphics card into slot 1 or slot 2.
In Table 26, use path console graphics3 for configuration numbers 6,
and 7.
192
Download from Www.Somanuals.com. All Manuals Search And Download.
The Boot Console Interface
Displaying and Setting the Monitor Type
Setting the Monitor Type at Power On
If you replace your workstation’s monitor with a different monitor type, and
do not set the workstation’s graphics parameters by using the monitor com-
mand before doing so, you need to perform the following:
If your keyboard connects to the PS/2 connector on your system, wait 2 sec-
onds after the Num Lock light flashes near the end of the boot sequence,
then press Tab to initiate the automatic monitor selection process.
If you have a keyboard that connects to the HIL connector on your system,
press Tab every three seconds during the boot sequence to initiate the auto-
matic monitor selection process.
Your system queries you for the new monitor type. Select the new type by
pressing Enter. The system queries you to confirm your selection. Press y to
save this monitor type.
If you don’t press y, the system stops cycling. You can use the monitor
graphics command in the configuration menu to change monitor type.
193
Download from Www.Somanuals.com. All Manuals Search And Download.
The Boot Console Interface
Displaying the Current Memory Configuration
Displaying the Current Memory Configuration
The following sample screen output using the memory command shows:
first, a memory configuration table with properly-installed and configured
memory (Sample Output 1); and second, output when a SIMM has been
improperly installed (Sample Output 2).
To display the current memory configuration for your system, from the
Information Menu of the boot console interface, follow the directions in
“Accessing the Boot Console Interface” earlier in this appendix. Once you
are in the Boot Console Interface Main Menu, type:
Main Menu: Enter a command or a menu > information
This places you in the Information Menu. From here type:
Information Menu: Enter command > memory
The screen displays a list of the current memory SIMMs configured for your
workstation.
194
Download from Www.Somanuals.com. All Manuals Search And Download.
The Boot Console Interface
Displaying the Current Memory Configuration
Sample Output 1
The following sample shows the memory configuration table when memory
SIMMs are properly installed and configured.
MEMORY INFORMATION
DETAILED MEMORY CONFIGURATION TABLE
SPA
---
GROUP
-----
SMC
---
0
SMC Status Bank
---------- ----
Bank Status
-----------
Configured
Configured
Configured
Configured
Configured
Configured
Size
----
64MB
16MB
64MB
16MB
16MB
16MB
Slot/Sys Brd
------------
0a/b
0x00000000 0
Configured
Configured
Configured
Configured
Configured
Configured
3
0
0
3
3
0
1
2a/b
2
0a/b
3
2a/b
0x04000000 1
1
1a/b
3
1a/b
Group 0 interleaved 4 ways over 4 banks
Group 1 interleaved 2 ways over 2 banks
Active, Installed Memory (bytes) :201326592 of Standard DRAM’s
Deallocated Pages (bytes)
-
0
---------
:201326592
Available Memory (bytes)
Good Memory Required by OS (bytes): 8151040
Memory
HVERSION SVERSION
-------- ---------
0x0490
0x00000900
195
Download from Www.Somanuals.com. All Manuals Search And Download.
The Boot Console Interface
Displaying the Current Memory Configuration
Sample Output 2
The following sample shows the memory configuration table when a
memory SIMM has been improperly installed, or not installed in pairs. In
this example, there is only one SIMM installed in slot 4a. Note that now the
BAD MEMORY TABLE is displayed.
MEMORY INFORMATION
WARNING: Memory banks deallocated due to a SIMM size mismatch or a SIMM failure.
Refer to the ME command in the INFORMATION menu for error information.
DETAILED MEMORY CONFIGURATION TABLE
SPA
---
GROUP
-----
SMC
---
0
SMC Status Bank
---------- ----
Bank Status
-----------
Configured
Configured
Configured
Configured
Configured
Configured
Size
----
16MB
16MB
16MB
16MB
64MB
64MB
Slot/Sys Brd
------------
0a/b
0x00000000 0
Configured
Configured
Configured
Configured
Configured
Configured
3
0
0
3
3
0
1
2a/b
2
0a/b
3
2a/b
0x04000000 1
1
1a/b
3
1a/b
Group 0 interleaved 4 ways over 4 banks
Group 1 interleaved 2 ways over 2 banks
BAD MEMORY TABLE
SMC
---
1
SMC Status
----------
Present
Bank
----
1
Bank Status
------------
Sizing Error
Sizing Error
SIMM Size
---------
0MB
Slot/Sys Brd
------------
4a/b
3
Present
2
0MB
4a/b
Active, Installed Memory (bytes) :201326592 of Standard DRAM’s
Deallocated Pages (bytes)
-
0
---------
:201326592
Available Memory (bytes)
Good Memory Required by OS (bytes):
8151040
Memory
HVERSION SVERSION
-------- ---------
0x0490
0x00000900
196
Download from Www.Somanuals.com. All Manuals Search And Download.
The Boot Console Interface
Displaying the Status of the EISA Slots
Displaying the Status of the EISA Slots
The eisa command lets you identify all EISA cards currently installed on
your workstation by showing you the current status of your workstation’s
four EISA slots. It is available only in the Information Menu.
To use the eisa command from the Information Menu of the boot console
interface, type:
Information Menu: Enter command > eisa
The following table appears:
Slot #
Slot State
------------
Empty
Device Information
--------------------
Empty
-------
1
2
3
Unconfigured
Empty
HWP1850
Empty
In the table above, “Slot #” is the slot number as seen on the back of your
workstation; “Slot State” is the current state of any card in each slot; and
“Device Information” is the compressed EISA ID, read from the EISA card
itself.
197
Download from Www.Somanuals.com. All Manuals Search And Download.
The Boot Console Interface
Setting the Auto Boot and Auto Search Flags
Setting the Auto Boot and Auto Search Flags
auto boot and auto search are variables stored in your workstation’s non-
volatile memory. (Nonvolatile memory retains its contents even after power
is turned off.) If you reset these flags to new value, the change takes effect
the next time you reboot the workstation.
auto boot boots the operating system whenever your workstation is turned
on.
To examine the state of the auto boot and auto search flags, type the fol-
lowing at the prompt:
Configuration Menu: Enter command > auto
If auto boot is set to on, your workstation automatically attempts to boot the
operating system when turned on. If auto boot is set to off, your workstation
enters the boot administration mode of the boot console user interface.
The state of the auto search flag determines how your workstation seeks a
boot device during autoboot. If auto search is set to on, your workstation
will search for other boot devices if the primary boot device is not available.
If auto search is off, your workstation will default to the boot administration
mode if it can’t see the primary boot device.
To change the state of the auto boot or auto search flags, type the following
at the prompt:
Configuration Menu: Enter command > auto boot state
or
Configuration Menu: Enter command > auto search state
where state is on or off.
198
Download from Www.Somanuals.com. All Manuals Search And Download.
The Boot Console Interface
Setting the Auto Boot and Auto Search Flags
Autosearch searches for devices in the following order:
Primary Boot Path
Alternate Boot Path
Built-in Fast, Wide SCSI Devices
Built-in Single-Ended SCSI Devices
Built-in LAN bootp servers
NOTICE:
Fast Wide SCSI adapter option cards installed in the option slots are not
searched unless they are referenced by the primary or alternate boot paths.
EISA cards are not searched.
199
Download from Www.Somanuals.com. All Manuals Search And Download.
The Boot Console Interface
Displaying and Setting the Fastboot Mode
Displaying and Setting the Fastboot Mode
When fastboot is enabled (set to on), your workstation does a quick check
of the memory and skips I/O interface testing during its power-on self tests.
This enables your workstation to complete its boot process quicker. The
default factory setting is for fastboot to be enabled (on).
The fastboot mode allows your workstation to boot quickly by performing a
less extensive check of the system’s memory.
When fastboot is disabled (set to off), more extensive memory testing and
I/O interface testing is performed during the self tests, causing the boot pro-
cess to take longer.
If you are experiencing difficulty in booting your workstation, set fastboot
to off and reboot the system. The more extensive testing may reveal the error
condition.
To display the status of fastboot, type the following at the prompt:
Configuration Menu: Enter command > fastboot
To disable fastboot, type the following at the prompt:
Configuration Menu: Enter command > fastboot off
To enable fastboot, type the following at the prompt:
Configuration Menu: Enter command > fastboot on
200
Download from Www.Somanuals.com. All Manuals Search And Download.
The Boot Console Interface
Displaying the LAN Station Address
Displaying the LAN Station Address
It is sometimes necessary to supply a LAN station address of your worksta-
tion to other users. For example, if your workstation is to become a member
of a cluster, the cluster administrator needs to know your LAN station
address in order to add your workstation to the cluster.
A LAN station address of your workstation is the label that uniquely identi-
fies the LAN connection for your workstation at the link level (the hardware
level).
To display your workstation’s LAN station addresses, type the following at
the prompt:
Configuration Menu: Enter command > lanaddress
The LAN station address is displayed as a twelve-digit number in hexadeci-
mal notation, similar to the following:
LAN Station Addresses:
080009-789abc
The address is for the system’s built-in LAN.
201
Download from Www.Somanuals.com. All Manuals Search And Download.
The Boot Console Interface
Displaying System Information
Displaying System Information
The all command allows you to display the system’s processor revision and
speed, cache size, memory size, flag settings, and the boot and console
paths. To display system information from the Information Menu, type the
following at the prompt:
Information Menu: Enter command > all
This information is paged to allow you to view it as necessary.
202
Download from Www.Somanuals.com. All Manuals Search And Download.
The Boot Console Interface
Displaying PIM Information
Displaying PIM Information
The pim command allows you to display the most recent PIM information
for the specified fault type. To display PIM information for a specific fault,
from the Service Menu, type the following at the prompt:
Service Menu: Enter command > pim processor_number
You can use pim in the following ways:
pim - gives all fault types
pim 0 - HPMC information on processor
pim 0 fault_type - fault type information on processor
203
Download from Www.Somanuals.com. All Manuals Search And Download.
The Boot Console Interface
Displaying PIM Information
204
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
absolute pathname The full pathname ly speaking, a pixmap of depth one, ca-
of a file, including all the directories
leading to it, starting with the root direc-
tory (“/”) and ending with the filename
itself. See also file, filename, path-
name.
pable of representing 2-color images.
boot Short for bootstrap service. A ser-
vice provided by a short program, stored
in the read-only memory of your work-
station, that loads the operating system
(or any complex program) into main
access permissions Settings that allow
a user or group of users to read, write, or memory. Partner workstations provide
execute files. See also file access per-
missions.
bootstrap service to diskless worksta-
tions. See also boot ROM.
active window The window that is re-
ceiving input from the keyboard at the
present time. If there is no active win-
boot console interface The interactive
firmware that enables you to interact
with the hardware of your workstation
dow, anything you type is lost. Only one before the workstation boots the operat-
window can be active at a time. The ac- ing system. The boot console interface
tive window is said to have the “key-
board focus.”
allows you to perform special tasks, dis-
play information, and set certain system
parameters.
ANSI The American National Stan-
dards Institute, a non-profit organization, boot ROM A read-only memory that is
made up of various expert committees,
that publishes standards for use by na-
tional industries. ANSI has adopted the
IEEE standards for local area networks.
incorporated into a workstation for the
purpose of starting the operating system,
testing the terminal, and producing a
standard display.
argument The part of a command line
that identifies the file or directory to be
acted on.
bootstrap service See boot.
byte A fundamental character-code
unit, usually consisting of 8 bits.
attachment unit interface (AUI) A
transceiver cable that conforms to IEEE
802.3 specifications.
CD-ROM Compact Disc Read-Only
Memory. See also CD-ROM disc, CD-
ROM drive.
back up v. To make a copy of the file
system on a tape or disk that can be
stored separately from the original files.
Also called “backing up the system” or
simply “system backup.”
CD-ROM disc CD-ROM discs are
identical to the audio compact discs
(CDs) used to record stereo music, ex-
cept that they store data. CD-ROM discs
are 120 mm (4.7 inches) in diameter, and
bitmap Generally speaking, an array of use one data surface with a capacity of
data bits used for graphic images. Strict- 600 MB. The data surface contains pits
205
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
and flat spots arranged in a continuous
spiral track, which is read at a constant
speed.
cluster server A workstation that pro-
vides file access, login access, file trans-
fer, printing, and other services across a
network to a defined cluster of systems
(cluster nodes) connected via a LAN.
See also cluster, cluster client, cluster
node, host.
CD-ROM drive A random-access,
read-only, mass-storage device that uses
removable CD-ROM discs. The drive
contains a semiconductor laser for read-
ing data optically and an embedded con- command An instruction that you enter
troller with a SCSI interface.
into the system at a prompt, to execute a
program or perform a task. See also shell
command.
Central Processing Unit (CPU) The
part of a workstation that interprets and
executes instructions.
command argument Information you
provide on a command line to describe
the object (usually a file or directory) to
be operated on by the command.
child directory See subdirectory.
click To press and release a mouse but-
ton. The term comes from the fact that
pressing and releasing most mouse but-
tons makes a clicking sound.
command interpreter A program that
reads lines of text from standard input
(typed at the keyboard or read from a
file) and interprets them as requests to
execute other programs. An HP-UX
command interpreter is called a shell.
See also shell.
cluster A group of workstations con-
nected via a Local Area Network (LAN).
One workstation, the cluster server, per-
forms as a file-system server for the clus-
ter clients. See also cluster client,
cluster node, cluster server.
command option Information you pro-
vide on a command line to indicate any
special action you want the command to
take. See also default.
cluster client A cluster node that does
not have a local HP-UX file system. Its
file system resides on the cluster server.
See also cluster, cluster node, cluster
server.
configuration The arrangement of a
workstation or network as defined by the
nature, number, and chief characteristics
of its functional units. More specifically,
the term configuration may refer to a
hardware configuration or a software
configuration.
cluster node A member of a group of
workstations connected via a Local Area
Network (LAN). One workstation, the
cluster server, performs as a server to the
cluster. See also cluster, cluster client,
cluster server.
control key sequence A keystroke
combination used as a shorthand way of
specifying commands. To enter a control
key sequence, you hold down the control
206
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
key while pressing another key.
choice of one or more options. If you
don’t specify an option, the command
automatically assigns one. This automat-
ic option is called the default. See also
command option.
cpu See Central Processing Unit.
CRX color graphics Expanded graph-
ics capability offering 24-plane color,
24-plane Z-buffered color, or 48-plane
Z-buffered color capability.
dialog box A special type of HP VUE
screen that is called by the user from a
window. Dialog boxes contain controls
and settings. To display an example of a
dialog box, click the Style Manager but-
ton on the Workspace, then click on Col-
or.
current directory See current work-
ing directory.
current session The work and process-
es that have been created since you
logged into the system (and before you
log out again). See also session.
directory A special type of object that
contains information about the objects
beneath it in the HP-UX organizational
structure. Basically, it is a file that stores
names and links to files and other direc-
tories. See also file.
current working directory The direc-
tory in which a relative path name search
begins, as well as the directory in which
you are currently working. It is also
called the working directory or current
directory.
disk A thin, round plate with a magnetic
surface coating on which data is stored
by magnetic recording. See also floppy
diskette, hard disk, CD-ROM disc.
cursor The small blinking box dis-
played in whatever screen is active at a
particular time. The cursor marks your
current typing position on the screen and
indicates which program (HP VUE ter-
minal window or shell) will receive your
commands.
disked workstation A workstation that
has its own hard disk drive. See also
diskless workstation, node, partner
node, workstation.
diskette See floppy diskette.
daisy-chaining A method of connect-
ing devices where the signal passes from
one device to the next in serial fashion
along a bus.
diskless booting Loading the operating
system into local memory from the disk
of a partner workstation.
diskless workstation A workstation
that has no disk. A diskless workstation
can use the disk of its partner worksta-
tion or other workstations. If necessary,
it can also use the computational services
of the partner workstation or other work-
DDS tape drive A device that stores
data on Digital Data Storage (DDS) cas-
settes.
default Most commands give you a
207
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
stations. A diskless workstation boots
from its partner workstation. See also
disked workstation, node, partner
node, workstation.
ETHERNET The LAN developed
jointly by Digital Equipment Corpora-
tion, Intel, and Xerox Corporation, upon
which the IEEE 802.3 network is based.
double click To press and release a
fast, differential SCSI An 8-bit wide
bus with high-power receivers and driv-
ers, which allows a cable length of up to
25 meters and a speed of up to 10 MB per
second. See also fast-wide SCSI, single-
ended standard SCSI, Small Comput-
er System Interface.
mouse button twice in rapid succession.
drag To press and hold down a mouse
button while moving the mouse (and the
pointer on the screen). See also drop.
drive See CD-ROM drive, DDS tape
drive, floppy drive, hard disk drive.
fast-wide SCSI A 16-bit wide bus with
high-power receivers and drivers, which
allows a cable length of up to 25 meters
and a speed of up to 20 MB per second.
See also fast, differential SCSI, single-
ended standard SCSI, Small Comput-
er System Interface.
drop To release an icon that has been
“dragged” to a new position. See also
drag.
EISA (Extended Industry Standard
Architecture) An industry standard bus
architecture based on and compatible
with that used by IBM in their AT series
computers.
file The basic named unit of data stored
on disk. See also directory, filename.
file access permissions The access
rights given to a particular file or directo-
ry. Every file and directory has a set of
access permissions, a code that deter-
mines whether a process can perform a
requested operation on the file (such as
opening the file or writing to it). See also
access permissions.
environment The conditions under
which your commands are executed.
These conditions include your worksta-
tion characteristics, home directory, and
default search paths. See also environ-
ment variables.
environment variables The set of de-
fined shell variables (some of which are
PATH, TERM, SHELL, EXINIT,
HOME) that define the conditions under
which your commands are executed.
These conditions include your worksta-
tion characteristics, home directory, and
default search paths. See also environ-
ment.
File Manager The HP VUE application
that allows you to manage your files and
directories, and to set viewing preferenc-
es.
filename The name given to a particular
file. See also absolute pathname, file,
pathname.
file server A workstation whose prima-
208
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
ry task is to control the storage and re-
trieval of data from hard disks. Any
number of other workstations can be
resenting the home directory. This is the
directory in which you are placed after
you log in. Typically, this is /users/
linked to the file server in order to use it login, where login is your username. See
to access data.
also home directory.
file system The organized set of files
and directories on a hard disk.
home directory A shorthand way of re-
ferring to a frequently used directory, al-
most always the login directory.
firmware The control software that is
embedded in ROM and is always resi-
dent despite the status of the operating
system. It handles the booting of the sys-
tem, initialization of I/O, and starts the
loading of the operating system.
host See cluster server.
host name See internet protocol ad-
dress.
HP-UX cluster See cluster node, clus-
ter server.
floppy diskette A thin, record-shaped
plate that stores data on its magnetic sur-
faces. The system uses heads (similar to
heads in tape recorders) to read and write
data on concentric disk tracks.
HP Visual User Environment A user
interface that draws a graphical layer
over the complexities of the other layers
of the system (the hardware, operating
system, and X Window system), en-
abling you to control your workstation
by directly manipulating graphical ob-
floppy drive A device that stores data
on a flexible diskette.
hard disk A type of disk that is rigid as jects instead of by typing commands at a
opposed to a floppy diskette, which is
flexible.
command-line prompt.
HP VUE See HP Visual User Envi-
ronment.
hard disk drive A device that stores
data on a hard disk. The hard disk is a
permanent part of the drive and cannot
be removed.
icon A small, graphic representation of
an object. Objects can be “iconized”
(turned into icons) to clear a cluttered
workspace. Icons can be restored to their
original appearance when needed. What-
ever processes are executing in an object
continue to execute when the object is
iconized.
HCRX color graphics Accelerated 8-
plane or 24-plane graphics. See also
CRX color graphics.
Help Manager The HP VUE applica-
tion that provides online help.
iconify See iconize.
$HOME The environment variable rep-
209
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
iconize To turn a window or shell into
an icon. See also icon.
LAN station address See local area
network station address.
Initial System Loader The program
that actually controls the loading of the
operating system.
link n. A special object that contains the
name of another object. When you spec-
ify a link as a pathname or part of a path-
name, the system substitutes the
pathname that the link contains.
input device Any of several pieces of
hardware equipment used to give infor-
mation to a system. Examples are the
keyboard and the mouse. See also out-
put device.
v. To join together two or more objects.
local area network (LAN) A data
communications system that allows a
number of independent devices to com-
municate with each other. The systems
and clusters that share data, hardware,
and software resources via Networking
Services software.
input window The window that dis-
plays a program’s prompt and any com-
mands typed but not yet executed.
internet protocol address (IP ad-
dress) A string of characters that
uniquely identifies a workstation in a
network. Also referred to as the IP ad-
dress, the system name, and the host
name.
local area network system address
The label that uniquely identifies the lo-
cal area network (LAN) connection for
your workstation at the hardware level.
invisible filename A filename in which
the first character is a dot (.). Invisible
filenames are not displayed by the listing
commands such as ls and ll without add
options, such as -a.
log in To initially sign on to the system
so that you may begin to use it. This cre-
ates your first user process. See also
username.
login directory The directory in which
you are placed when you log in, usually
your home directory. See also home di-
rectory.
IP address See internet protocol ad-
dress.
ISL See Initial System Loader.
Login Manager The program that con-
trols the initial startup of HP VUE and
accepts the user’s username and pass-
word.
kernel The part of the operating system
that is an executable piece of code re-
sponsible for managing the computer’s
resources. The kernel controls the rest of
the operating system.
login script The shell program that runs
at each login, and sets the login environ-
ment for your system.
LAN See local area network.
210
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
menu bar An area at the top or bottom nonvolatile memory System memory
of a window that contain the titles of the that retains its contents even after work-
pull-down or pop-up menus for that ap-
plication.
station power is turned off.
object Any file, directory, or link in the
network. See also directory, file, link,
minimize button In HP VUE, a push
button on the window frame that turns a pathname.
screen into an icon. See also icon,
iconize.
operating system The program that su-
pervises the execution of other programs
on your workstation. For example, the
entire HP-UX system, including the ker-
nel and all HP-UX commands. See also
kernel.
mouse pointer See pointer.
name A character string associated with
a file, directory, or link. A name can in-
clude various alphanumeric characters,
but never a slash (/) or null character. See option See command option.
also pathname.
output device Any of several pieces of
network Two or more workstations
sharing information. See also cluster,
workstation.
hardware used for receiving messages
from the workstation. Display screens
and printers are examples of output de-
vices. See also input device.
network controller A printed circuit
board that passes bit streams between the output window The window that dis-
network and the main memory of the
workstation. Coupled with the network
transceiver, the controller also handles
signal processing, encoding, and net-
work media access.
plays a process response to your com-
mand.
parent directory A directory that con-
tains other directories, each of which is
then called a subdirectory. See also sub-
directory.
node A network computer (worksta-
tion). Each node in the network can use
the data, programs, and devices of other
network nodes. Each node contains main
memory and has its own disk or shares
one with another node. See also disked
workstation, diskless workstation,
workstation.
partner node A workstation that shares
its disk with a diskless node. See also
diskless workstation.
password The word you enter next to
the password prompt at login time. Keep
your password secret and change it occa-
sionally in order to protect your account
from unauthorized use. See also user ac-
count.
node name A unique identifying name
given to a workstation in a cluster. See
also cluster, node.
211
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
path The hardware address of a device
that is attached to the I/O system of your
workstation.
grams.
prompt A message or symbol displayed
by the system to let you know that it is
ready for your input.
pathname A series of names separated
by slashes that describe the path of the
operating system from some starting
point in the network to a destination ob-
ject. Pathnames begin with the name of
the starting point, and include every di-
rectory name between the starting point
and the destination object. A pathname
ends with the name of the destination ob-
ject. See also name, object.
push button A graphic control that
simulates a real-life push button. Use the
pointer and mouse to push the button and
immediately start an action.
RAM Random access memory.
ROM Read-only memory.
root See superuser.
permissions A set of rights (read, write,
execute) associated with an object in the
file system. Determines who may use the
object.
scroll bar A vertical or horizontal bar
located on the side or bottom of a win-
dow that allows the user to view infor-
mation that does not fit within the
window.
PID Process Identification. Also re-
ferred to as a process ID. See also pro-
cess ID.
SCSI See Small Computer System In-
terface.
pointer Sometimes called the “mouse
pointer,” the pointer shows the mouse lo-
cation on the screen. The pointer’s shape
depends on its location. In the HP VUE
Workspace, the pointer is an X. On a
window frame, the pointer is an arrow.
server A program that controls all ac-
cess to input and output devices.
session The time between when you log
in and when you log out. Also called a
work session or a login session. See also
current session.
process A computing environment in
which you may execute programs; a pro-
gram currently running in the system.
shell A command-line interpreter pro-
gram used to invoke utility programs.
Some examples of HP-UX shells are the
Bourne, Korn, Key, and C shells. Some-
times referred to as a command interpret-
er. See also command interpreter.
process ID A unique identification
number assigned to all processes by the
operating system. Also referred to as a
PID. See also PID.
program A unit of executable code, in
binary or “source” form. Most HP-UX
commands and routines consist of pro-
shell command An instruction you
212
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
give the system to execute a utility pro-
gram or shell script. See also shell
script, utility program.
Style Manager The HP VUE applica-
tion that provides the ability to custom-
ize various aspects of your system,
including colors, fonts, the keyboard, the
mouse, session startup and termination
behavior, and access to other worksta-
tions.
shell script A file that contains com-
mands that the system can interpret and
run in a shell.
subdirectory A directory that is located
in, or anywhere on a path below, another
directory. The directory above the subdi-
rectory is called the parent directory. The
subdirectory is also referred to as the
child directory. See also parent directo-
ry.
shutdown The process of taking the
system from multi-user state to system
administration state.
SIMM See Single In-line Memory
Module.
single-ended standard SCSI An 8-bit
wide SCSI bus with standard receivers
and drivers, which limits total cable
length to 6 meters. See also fast, differ-
ential SCSI, fast-wide SCSI, Small
Computer System Interface.
superuser A user with permission to
enter the top-level directory and make
changes to files and programs that users
are not allowed to change. To “become
superuser” or “become root” means to
let the system know that you are now as-
suming the role of system administrator.
You can do this either by logging into the
system as root, or by typing su at a com-
mand-line prompt. You must know the
root password to become root.
Single In-line Memory Module A
memory board.
slider One of the components of a scroll
bar. The slider is the object that is
dragged along the scroll area to cause a
change.
system administrator The person re-
sponsible for system and network instal-
lation, updating, maintenance, and
security at your site.
Small Computer System Interface
(SCSI) An IEEE standard for interfac-
ing a computer to multiple, disparate
high-speed peripherals such as a floppy
disk or a CD-ROM, singly or in combi-
nation. See also fast, differential SCSI,
fast-wide SCSI, single-ended standard
SCSI.
system call Invocation of a kernel pro-
cess by a user program.
system name See internet protocol
address.
terminal window A terminal window
is a type of HP VUE window that emu-
lates a complete display terminal. Termi-
nal windows are typically used to fool
standalone A workstation that is not
part of a cluster. See also cluster.
213
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
non-client programs into believing they
are running in their favorite terminal.
When not running programs or execut-
ing operating system commands, termi-
nal windows display the command-line
prompt. See also HP Visual User Envi-
ronment.
utility program A program provided
with the operating system to perform a
frequently required task, such as printing
a file or displaying the contents of a di-
rectory. See also command, shell com-
mand.
window A rectangular area of the
screen for viewing information. HP VUE
allows you to create several types of win-
dows on the screen. Each window is a
separate computing environment in
which you may execute programs, edit
text, or read text. See also Workspace
Manager.
title bar The rectangular area between
the top of the window and the window
frame, that contains the title of the win-
dow object.
transceiver A device that transmits and
receives signals.
Window Manager The HP VUE pro-
gram that controls the size, placement,
and operation of windows.
user account The system administrator
defines a user account for every person
authorized to use the system. Each user
account contains the name the computer
uses to identify the person (user ID), and
the person’s password. User accounts
also contain project and organization
names, to help the system determine who
can use the system and what resources
each person or organization can use. See
also user ID, password.
working directory See current work-
ing directory.
Workspace What the screen becomes
when you start HP VUE. Although you
can hide the workspace under terminal
windows or other graphic objects, you
can never position anything behind the
workspace. All windows and graphic ob-
jects appear stacked on the workspace.
See also HP Visual User Environment,
user ID The name the computer uses to
identify you. Your system administrator
assigns you a user ID. Enter your user ID
during the login procedure when the sys- terminal window.
tem displays the login prompt. See also
user account.
Workspace Manager The program
that controls the size, placement, and op-
eration of windows on the HP VUE
Workspace. The Workspace Manager is
a special Window Manager. See also
Window Manager.
username The name that the system
recognizes as uniquely yours. Also
known as your login name. The user-
name is also the name that identifies you
to the mail system and other software re-
quiring secure entry.
workstation A compact, graphics-ori-
ented computer having high speed and
high memory capacity. A workstation
utility See utility program.
214
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
usually includes a keyboard, a monitor,
and a system unit. See also node, disked
workstation, diskless workstation.
215
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
216
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
217
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
218
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
219
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
220
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
221
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
222
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
223
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
224
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
225
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
226
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
227
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
228
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
229
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
230
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
231
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
232
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
Symbols
$HOME,, 209
searching for,, 183
bootstrap service,, 205
byte,, 205
mediainit,, 85
memory,, 194
path,, 185
A
pim,, 203
absolute pathname,, 205
access permissions,, 205
active window,, 205
ANSI,, 205
applications
ftp,, 26
rcp,, 26
rlogin,, 26
telnet,, 25
reboot,, 36
reset,, 184
rlogin,, 26
search,, 183
C
CD-ROM disc
busy light during self test,, 59
mounting and unmounting,, 54
mounting using SAM,, 54
unmounting using SAM,, 57
CD-ROM disc,, 205
CD-ROM discs
tar,, 74
configuration,, 206
connectors, system unit
audio,, 10
caring for,, 44
keyboard,, 12
archiving data
listing files,, 75
restoring files,, 75
saving to a cassette,, 74
archiving data,, 74
argument,, 205
attachment unit interface (AUI),, 205
audio
CODEC,, 10
CD-ROM drive
controls and features,, 41
description,, 41
troubleshooting,, 61
using device files,, 53
verifying operation,, 51
CD-ROM drive,, 206
CD-ROM media,, 44
CD-ROM,, 205
power cord,, 14
SCSI,, 13
connectors, system unit,, 8
connectors,keyboard
802.3 network,, 12
HP parallel I/O,, 12
ITF,, 12
PS/2 and mouse,, 12
serial I/O,, 12
converting dB to number significant
bits,, 11
electrical specifications,, 11
features,, 10
headphone jack, 7
input,, 10
microphone jack, 7
mute button, 7
Central Processing Unit (CPU),, 206
child directory,, 206
click,, 206
cluster client,, 206
cluster node,, 206
cluster server,, 206
cluster,, 206
command argument,, 206
command interpreter,, 206
command option,, 206
command,, 206
control key sequence,, 206
controls, system unit
audio, 7
power LED,, 6
power switch,, 6
system LEDs,, 6
cpu,, 207
CRX color graphics,, 207
current directory,, 207
current working directory,, 207
cursor,, 207
output,, 10
volume control, 7
auto boot,, 198
auto boot, changing state,, 198
auto search,, 198
auto search, changing state,, 198
commands
/dev, 84
/etc/lanscan,, 22
/rfloppy, 84
D
daisy-chaining,, 207
data cassettes
B
/use/sbin/lanscan,, 22
all,, 202
auto,, 198
boot,, 181
cd,, 87
eisa,, 197
etc,, 36
fastboot,, 200
cleaning heads,, 69
media life,, 68
back up,, 205
bitmap,, 205
boot console
accessing,, 180
features,, 177
menus,, 177
media restrictions,, 69
ordering information,, 78
setting write-protect tab,, 69
data compression,, 65
data compression,using,, 74
DDS tape drive
boot console interface,, 205
boot ROM,, 205
boot,, 205
lanaddress,, 201
lp .vueprofile,, 34
man,, 25
controls and indicators,, 65
LED code warning conditions
bootable media
217
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
emissions regulations
Federal Communications Commission
(FCC),, 107
third party compliance,, 108
environment variables,, 208
environment,, 208
H
high humidity,, 67
media wear,, 68
selft-test,, 67
hard disk drive
configuring,, 136
hard disk drive,, 209
hard disk,, 209
HCRX color graphics,, 209
Help Manager,, 209
home directory,, 209
host name,, 209
host,, 209
HP Visual User Environment,, 209
HP VUE,, 209
LED codes,, 66
loading and unloading data cassette,, 71
troubleshooting,, 77
using device files,, 73
verifying operation,, 72
DDS tape drive,, 207
DDS tape drives
operating,, 71
default,, 207
device file name
CD-ROM drive,, 23
DDS-format tape drive,, 23
device files
data compression,, 73
no data compression,, 73
diagnostics
SupportWave,, 102
SupportWave,running,, 103
system verification tests,, 102
dialog box,, 207
ETHERNET,, 208
F
fast, differential SCSI,, 208
fastboot
disabling,, 200
displaying status,, 200
enabling,, 200
HP-UX cluster,, 209
fastboot,, 200
I
icon,, 209
fast-wide SCSI,, 208
file access permissions,, 208
File Manager,, 208
file server,, 208
file system,, 209
file,, 208
filename,, 208
floor stand, removing,, 117
floppy diskette
formatting,, 85
inserting and removing,, 82
listing files,, 88
restoring files from,, 87
saving files to,, 86
setting write-protect,, 81
transferring data,, 86
floppy diskette,, 209
floppy drive
iconify,, 209
iconize,, 210
Initial System Loader,, 210
input device,, 210
input window,, 210
internal storage
configuring, 120
internal storage devices,, 4
internet protocol address,, 210
invisible filename,, 210
IP address,, 24, 210
ISL,, 210
directory,, 207
disk,, 207
disked workstation,, 207
diskette,, 207
diskettes
K
ordering information,, 91
diskless booting,, 207
diskless workstation,, 207
documentation conventions, xvii
double click,, 208
drag,, 208
kernel,, 210
keyboards
differences between PS/2 and ITF,, 16
equivalent keys,, 16
ITF,, 16
operating,, 83
verifying configuration,, 83
floppy drive,, 209
floppy drive, device files,, 84
floppy driver
PS/2,, 16
drive,, 208
drop,, 208
keyboards,, 4
configuring,, 90
L
E
LAN station address,, 201, 210
LAN station address,displaying,, 201
LAN,, 210
EISA option board
installing,, 147
G
graphics configuration
graphics3, 187
graphics4, 187
GSC option board
installing,, 147
EISA slots
displaying status,, 197
EISA,, 208
EISA/GSC,, 4
electrostatic discharge (ESD) precatuions,,
109
LANIC ID,, 21
link,, 210
local area network system address,, 210
local area network,, 210
log in,, 210
login directory,, 210
218
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
Login Manager,, 210
login script,, 210
P
ROM,, 212
root,, 212
parent directory,, 211
partner node,, 211
password,, 211
M
S
path
main memory,, 3
main tray assembly
removing,, 139
replacing,, 141
scroll bar,, 212
displaying,, 185
setting,, 186
SCSI bus
differences,, 159
path,, 185, 212
pathname,, 212
permissions,, 212
PID,, 212
PIM information,displaying,, 203
pointer,, 212
fast, wide differential SCSI-3 length,,
167
fast, wide differential,, 159
single-ended SCSI-2 length,, 165
single-ended,, 159
SCSI device IDs
media, interchangeability restrictions,, 76
memory
displaying configuration,, 194
installing additional,, 143
nonvolatile,, 198
pointing devices,, 19
printer
gathering information about,, 29
printing a file,, 37
menu bar,, 211
minimize button,, 211
monitor
assigning,, 168
fast, wide differential,, 172
single-ended standard system,, 170
SCSI ID,, 23
changing type,, 155
setting up for network printing,, 35
setting up using SAM,, 30
solving problems,, 38
problems
802.3 network,, 96
boot device failure,, 101
loading and booting the operating sys-
tem,, 96
system power up,, 95
system verification tests,, 102
using CD-ROM drive,, 98
using DDS tape drive,, 99
using floppy disk drive,, 100
using hard disk drive,, 97
problems, questions, and suggestions, xviii
process ID,, 212
displaying type,, 187, 188
setting type at power on, 193
setting type at power on,, 155
setting type from boot console,, 155
setting type,, 187, 189
monitors,, 15
SCSI ports
connecting to,, 173
SCSI restrictions
cables,, 161
configuration constraints,, 162
connectors and terminators,, 162
fast, wide differential SCSI-3 configura-
tion constraints,, 163
SCSI,, 212
SCSI, checking the ID,, 115
server,, 212
session,, 212
shell command,, 212
shell script,, 213
shell,, 212
shutdown,, 213
SIMM,, 213
mouse pointer,, 211
N
name,, 211
network controller,, 211
Network File System (NFS),, 26
network,, 211
networking
mail,, 25
node name,, 211
node,, 211
process,, 212
Processor performance,, 3
program,, 212
prompt,, 212
nonvolatile memory,, 198, 211
Single In-line Memory Module,, 213
single-ended standard SCSI,, 213
SIO pin listing,, 13
slider,, 213
O
push button,, 212
object,, 211
operating system,, 3, 20, 211
option,, 211
ordering information
cleaning cassettes,, 78
data cassettes,, 78
diskettes,, 91
Small Computer System Interface (SCSI),,
213
standalone,, 213
standard I/O,, 4
standard network,, 4
storage devices
installing,, 119
removable,, 7
Style Manager,, 213
subdirectory,, 213
R
RAM,, 212
regulations
acoustics,, 108
laser safety statement,, 111
safety statement,, 110
related manuals, xv
release documents, xiv
revision history, xvi
output device,, 211
output window,, 211
219
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
subnetwork mask,, 24
superuser,, 213
system administrator,, 213
system call,, 213
system information,displaying,, 202
system name,, 213
T
tar command, additional information,, 76
terminal window,, 213
title bar,, 214
transceiver,, 214
U
user account,, 214
user ID,, 214
user interface,, 3
username,, 214
utility program,, 214
utility,, 214
W
warnings and cautions,, 112
Window Manager,, 214
window,, 214
working directory,, 214
Workspace Manager,, 214
Workspace,, 214
workstation
booting,, 181
features,, 3
preparing to change configuration,, 117
resetting to predefined parameters, 184
resetting,, 184
Workstation,, 214
220
Download from Www.Somanuals.com. All Manuals Search And Download.
|