HP Hewlett Packard Network Cables CN1000E User Manual

HP Emulex Converged Network Adapter  
Installation Guide  
Abstract  
This document provides information about installing, configuring, and troubleshooting the HP Emulex Converged Network  
Adapters (CNAs). In this document, CNA refers to HP models CN1000E and CN1100E.  
HP Part Number: AA-RWQAC-TE  
Published: August 2011  
Edition: 3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Contents  
Contents  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
4
Contents  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1 Installing the Emulex CNA  
This chapter describes the following topics for installing the CNA:  
See the server documentation for additional information about installing the CNA.  
WARNING! Disconnect the host from the power source before installing the CNA. To reduce the  
risk of personal injury from hot surfaces, allow the internal server or workstation components to  
cool before touching.  
Installation prerequisites  
Before you begin, make sure you have the following items available:  
An optical multimode cable with an LC-style duplex connector and approved SFP+ module or  
copper cable  
A server with an empty x8 PCIe bus slot  
Recording reference numbers  
Each CNA is shipped with the following two numbers clearly marked on the board:  
IEEE address (Port 1 MAC address)  
Serial number  
The MAC address is a unique 48-bit identifier used when configuring the system. The Fibre Channel  
industry uses the World Wide Name (WWN) derived from the MAC address for Fibre Channel  
connectivity. The adapter has two ports. Therefore, it has two MAC addresses and two WWNs,  
one for each port. Use the serial number when communicating with HP.  
NOTE: The factory default MAC addresses are permanent identifiers that cannot be changed.  
The MAC address for Port 1 is listed on the CNA. The MAC address for Port 2 and the WWNs  
are calculated based on the Port 1 address as follows:  
MAC address/WWN  
Calculation  
Example  
Port 1 MAC address  
Assigned at the factory and printed  
on the CNA IEEE address label  
F4-CE-46-FD-9C-68  
Port 1 WWN  
10:00:[Port 1 MAC address]  
Port 1 MAC address + 4  
10:00:F4:CE:46-FD-9C-68  
F4-CE-46-FD-9C-6C  
Port 2 MAC address  
Port 2 WWN  
10:00:[Port 1 MAC address + 4]  
10:00:F4:CE:46-FD-9C-6C  
Record the serial number and MAC addresses and WWNs for your CNA before installation.  
Serial number (on CNA): ________________________________  
Port 1 MAC address: ____________________________________  
Port 1 WWN: __________________________________________  
Port 2 MAC address: ____________________________________  
Port 2 WWN: __________________________________________  
Installation prerequisites  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
             
Installing the Emulex CNA  
The CNA uses removable optical transceivers or copper interface cables.  
CAUTION:  
Electrostatic discharge (ESD) can damage electronic components. Be sure you are properly grounded  
before beginning this procedure, as described in “Electrostatic discharge” (page 9).  
IMPORTANT: The CNA is only supported in PCI Express 8 lane and larger PCIe slots. This may  
require optional PCIe riser cards or cages. For instructions on installing the riser card or cage, see  
the server documentation.  
To install the CNA into a server:  
1. Be sure the server is powered off.  
2. Remove the access panel.  
3. Wearing an anti-static wrist strap, remove the blank panel from an empty x8 or larger PCIe  
bus slot.  
NOTE: The CNA comes with a standard PCIe bracket installed. A low-profile bracket is  
included in the box with the CNA. The low-profile mounting bracket is shorter than the standard  
bracket: approximately 7.90 cm (3.11 inches) compared to 12.06 cm (4.75 inches) long.  
4. If you require a different mounting bracket, change the bracket as follows. Otherwise, go to  
Step 5.  
a. Remove any transceivers or cables from the CNA transceiver cage assembly by pulling  
the bail (handle) out and down to release the latch, and then gently pull the transceiver  
out. Do not force it. After the latch is released, the transceiver/cable slides out easily.  
Figure 1 A typical optical transceiver  
Figure 2 Removing a transceiver  
b. Observing ESD precautions, store the transceiver in an ESD-safe place.  
c. Remove the mounting bracket screws from the top of the CNA.  
6
Installing the Emulex CNA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Figure 3 Removing the bracket  
d. Remove the bracket and store it for future use.  
e. Align the new mounting bracket tabs with the holes in the CNA.  
IMPORTANT: Be careful not to push the bracket past the grounding tabs on the  
transceiver housing. Make sure the LEDs are properly aligned with the holes in the bracket.  
f. Install the screws that attach the CNA to the bracket.  
g. Slide the transceiver into the housing. When the latch engages, it clicks.  
h. Push the bail back into place.  
5. Insert the CNA into the empty PCIe slot. Press firmly until the CNA is seated.  
6. Secure the CNA mounting bracket to the case with the panel clip.  
7. Replace the server case, and then tighten the screws on the case.  
The CNA is now installed in the server and ready for media attachment.  
Installing the Emulex CNA  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
8. Attach the media:  
a. For fiber optic cable connections:  
1. Insert the SFP transceiver module into the cage.  
2. Connect one end of the fiber optic cable to the LC connector on the CNA.  
3. Connect the other end of the cable to the Converged Network switch.  
Figure 4 Emulex CNA with optical transceivers  
Figure 5 Connecting fiber optic cable  
b. For copper cable connections:  
1. Connect one end of the copper cable to the CNA.  
2. Connect the other end of the cable to the Converged Network switch.  
Figure 6 Connecting the direct attach copper cable  
8
Installing the Emulex CNA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9. Apply the power:  
a. Verify that the CNA is installed securely in the server.  
b. Verify that the correct media is attached.  
c. Plug in and power on the server.  
d. Observe the Link and Activity LEDs to be sure the CNA connects to the switch.  
For more information about the meaning of the LED indicators, see “CNA LED states”  
e. Watch the server console for any POST error messages and the CNA BIOS startup  
message similar to the one in Figure 7 (page 9)  
Figure 7 CNA BIOS example startup message  
Electrostatic discharge  
To prevent damage to the system, be aware of the precautions you need to follow when setting  
up the system or handling parts. A discharge of static electricity from a finger or other conductor  
may damage system boards or other static-sensitive devices. This type of damage may reduce the  
life expectancy of the device.  
To prevent electrostatic damage, observe the following precautions:  
Avoid hand contact by transporting and storing products in static-safe containers.  
Keep electrostatic-sensitive parts in their containers until they arrive at static-free workstations.  
Place parts on a grounded surface before removing them from their containers.  
Avoid touching pins, leads, or circuitry.  
Always be properly grounded when touching a static-sensitive component or assembly (see  
Grounding methods  
There are several methods for grounding. Use one or more of the following methods when handling  
or installing electrostatic-sensitive parts:  
Use a wrist strap connected by a ground cord to a grounded workstation or computer chassis.  
Wrist straps are flexible straps with a minimum of 1 megohm (±10 percent) resistance in the  
ground cords. To provide proper ground, wear the strap snug against the skin.  
Use heel straps, toe straps, or boot straps at standing workstations. Wear the straps on both  
feet when standing on conductive floors or dissipating floor mats.  
Use conductive field service tools.  
Use a portable field service kit with a folding static-dissipating work mat.  
If you do not have any of the suggested equipment for proper grounding, have an HP-authorized  
reseller install the part.  
NOTE: For more information on static electricity, or assistance with product installation, contact  
your HP-authorized reseller.  
Electrostatic discharge  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
2 Installing drivers and software  
For the latest information about storage array support, see the HP SPOCK website at http://  
www.hp.com/storage/spock. You must sign up for an HP Passport to enable access.  
Some CNA download kits include a readme.txtfile that may contain additional information  
about installing firmware and drivers, plus enhancements and fixes in the current release. Information  
in the readme.txtfile supersedes this and other HP Emulex documents.  
The Emulex OneCommand Manager application is available for the CNA. See the Emulex  
OneCommand Manager Application User Manual:  
2. Under storage, click Storage Networking.  
3. Click HP Converged Network Adapters .  
4. Select Manuals.  
Order of the installation  
The order of installation is important. It must be done as follows:  
1. Install the network driver.  
2. Install the FCoE driver.  
3. Install the OneCommand Manager utility.  
4. Update the CNA firmware and BIOS (if required).  
5. Install multipathing software (if required).  
Downloading software and drivers  
This section describes how to locate and download drivers and software.  
Downloading the Windows Windows driver kit (Smart Component) or Linux driver  
kit  
To download the driver kit:  
2. Click Drivers & Software.  
3. Using the HP model number as your guide, enter the CNA model number, and then click  
Search.  
4. Select your operating system.  
5. Select the Windows driver kit (Smart Component) or Linux driver kit and download it to your  
server.  
NOTE: Install the network driver kit before you install the storage Fibre Channel driver.  
Downloading the OneCommand Manager application kit  
To download the OneCommand Manager application kit:  
2. Click Drivers & Software.  
3. Using the HP model number as your guide, enter the CNA model number, and then click  
Search.  
4. Select your operating system.  
5. Select the OneCommand Manager Application Kit and download it to your server.  
10  
Installing drivers and software  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                 
Downloading firmware  
To download firmware:  
2. Click Drivers & Software.  
3. Using the HP model number as your guide, enter the CNA model number, and then click  
Search.  
4. Click Cross operating system (BIOS, Firmware, Diagnostics, etc.).  
5. Select the Firmware image and download it to your server.  
Downloading multipathing software  
To download Windows MPIO DSM software:  
2. Click Drivers & Software.  
3. Enter MPIO DSM, and then click Search.  
4. Select the MPIO DSM software for your arrays and download it to your server.  
To download the Linux HP Device Mapper kit:  
2. Select your operating system.  
3. Select the Device Mapper Multipath Enablement Kit and download it to your server.  
Installing drivers and software  
This section describes how to install drivers and software.  
Installing the Windows device driver using the HP Smart Component kit  
To install the Windows drivers:  
1. Obtain the latest Smart Component for your configuration and copy it to your Windows server.  
2. Unzip the driver Smart Component.  
3. Double-click the FCoE Smart Component executable to begin the installation, and then click  
Install.  
The Smart Component automatically installs the FCoE driver without user intervention.  
4. Click Reboot to complete the installation.  
Installing the Windows utility using the HP Smart Component kit  
To Install the CNA Windows OneCommand Manager utility:  
1. Obtain the latest Smart Component for your configuration and copy it to your Windows server.  
2. Unzip the Smart Component.  
3. Double-click the network Smart Component executable to begin the installation, and then click  
Install.  
The Smart Component automatically installc the OneCommand Manager software without  
any user intervention. When the installation is finished, click Finish to complete the installation.  
NOTE: The NIC driver must be installed and the NIC ports enabled for the OneCommand  
Manager to operate properly.  
Installing drivers and software  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                   
Installing firmware on Windows systems  
Use the OneCommand Manager utility to install the CNA firmware/BIOS:  
1. Before you begin, make sure you have the following installed:  
Network driver  
FCoE driver  
OneCommand Manager utility  
2. Download the firmware image to your Windows server  
3. Follow the procedure in the Updating Adapter Firmware chapter of the OneCommand Manager  
Application User Guide.  
Installing multipathing software on Windows  
If you require multiple-path redundancy, after installing the operating system, you must install the  
HP-supplied MPIO DSM kits specific to your storage arrays:  
1. Download the MPIO software. See “Downloading multipathing software” (page 11).  
2. Double-click the executable file and follow the on-screen instructions.  
Installing the CNA Linux drivers  
NOTE: If performing a Boot from SAN (BFS) installation, do not install the uldkkit. You must  
install the FCoE and NIC drivers before installing the OneCommand Manager utility.  
Download the Linux driver kit as described in “Downloading the Windows Windows driver kit  
To install the Linux drivers, follow the instructions in the readme.txtfile that is included in the  
kit.  
Installing the Linux utility  
To install the Linux OneCommand Manager application kit:  
1. Download the appropriate utility kit for your distribution. See “Downloading the OneCommand  
2. Uncompress the file.  
3. Change to the elxocm-<operating system>-<version>directory.  
4. Execute the install command:  
# ./install.sh  
NOTE: The NIC driver must be installed and the NIC ports enabled for the OneCommand  
Manager to operate properly.  
Installing firmware on Linux systems  
To install the CNA firmware/BIOS image using the OneCommand Manager utility:  
1. Before you begin, make sure you have the following installed:  
Network driver  
FCoE driver  
OneCommand Manager utility  
2. Download the firmware image.  
3. Follow the instructions in the Updating Adapter Firmware chapter of the OneCommand  
Manager Application User Guide.  
12  
Installing drivers and software  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                   
Installing and configuring multipathing software on Linux  
If you require multiple-path redundancy, see the Native Linux Multipath Disk Arrays Device-Mapper  
for HP StorageWorks Reference Guide or download the HPDMmultipath-4.4.1 Enablement Kit.  
Both are available on the HP SPOCK website at http://www.hp.com/storage/spock. You must  
sign up for an HP Passport to enable access.  
After you log in, under Application Notes on the left of the screen, click Solutions: Linux.  
Installing drivers and software  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
3 Troubleshooting  
This chapter contains the following topics for information to help resolve potential CNA problems:  
Isolating CNA problems  
This section describes how to resolve typical problems with the CNA.  
Observe and collect data  
The first step in troubleshooting any CNA problem is to observe and collect information about the  
problem so the problem can be isolated. Consider the following:  
If the CNA has been working, what has changed? For example, changes to switch or storage  
system firmware could affect the CNA.  
Identify the expected and observed results.  
List as many of the observed symptoms as possible.  
Collect relevant information including, but not limited to:  
CNA firmware, BIOS, and utilities revision information  
Applicable switch and storage subsystems revision information  
Operating system driver and path management revision information and log files  
CNA LED and startup BIOS message  
Isolate the problem to the component  
After collecting the data, use the data to isolate the problem to a particular component. The typical  
components in a CNA solution are a server with a CNA, cables, Converged Network (CN) switch,  
storage subsystem, and Fibre Channel switches. Because the focus on this chapter is the CNA, this  
section describes typical CNA problem isolation.  
CNA problem isolation  
Most of the common problems with the CNA are either link connectivity issues, which affect both  
Ethernet and Fibre Channel access, or Fibre Channel storage discovery issues.  
Verify server and CNA startup BIOS messages  
1. Look for server POST errors.  
2. Verify that the CNA is detected and has the appropriate firmware. See “CNA startup BIOS  
If either of these steps reveals errors, the most likely cause is a faulty CNA or the CNA is  
incompatible with the server model.  
Verify the CNA link  
1. Verify that the CNA link is active by observing the CNA LEDs. See “CNA LED states” (page  
16).  
2. Verify connectivity at the CN switch port. Use the appropriate switch management utility to  
display the port information and verify the CNA port WWN. See Figure 8 (page 15) and  
Figure 9 (page 15) for an example of displaying the CN switch link status.  
14  
Troubleshooting  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                     
Figure 8 Example of B-series loginshowoutput  
Figure 9 Example of C-series show interfaceoutput  
3. Observe the CN switch and CNA link error counters.  
If any of these steps detect errors, the most likely causes are incompatible or faulty cables, SFPs,  
or CN switch ports. Cable or SFP problems can cause a wide range of symptoms from solid to  
intermittent and even performance issues. The FCoE switch port and CNA port error counters are  
good indications of potential intermittent and performance problems.  
Verify Fibre Channel switch zoning for FC storage  
Verify that the Fibre Channel zoning and the CNA port WWNs match those displayed by the  
CNA.  
Verify Fibre Channel storage device discovery  
After verifying startup BIOS message, link, and zoning, verify that the CNA can discover the  
configured Fibre Channel storage devices.  
The first level of CNA Fibre Channel storage device discovery is performed at the BIOS level  
using the OneConnect FCoE BIOS utility. Use this utility (see “CNA startup BIOS message”  
Isolating CNA problems  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
(page 17)) at system startup to discover and display the storage devices in the attached FC  
fabric.  
When the server boots, the operating system performs the next level of discovery. Using the  
OneCommand Manager utility (see Figure 10 (page 16)), you can view all Fibre Channel  
storage devices known to the server.  
Figure 10 OneCommand Manager  
If the storage controller cannot be seen, then the most likely causes are Fibre Channel zoning or  
SAN connectivity between the CNA and the storage controller.  
If the storage controller can be seen, but not any of its LUNs, then the most likely cause of not  
seeing discrete LUNs is a LUN mapping problem.  
CNA LED states  
You can observe green and amber LEDs through openings in the CNA mounting bracket. See  
Figure 11 (page 17). Table 1 (page 17) describes the CNA LED link states.  
16  
Troubleshooting  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
NOTE: When power is applied to the CNA, both LEDs on both ports light for approximately 10  
seconds.  
Figure 11 CNA LED indicators  
Table 1 CNA LED descriptions  
LED  
Meaning  
Link activity (Green)  
Flash = activity  
Off = no activity  
Link state (Amber)  
On = link up  
Off = link down  
CNA startup BIOS message  
The CNA BIOS that is typically used to configure Boot from SAN (BFS) can also aid in  
troubleshooting CNA installation, SAN link, and zoning configuration issues. During the system  
startup the CNA startup BIOS message displays on the system console. This message provides  
minimal information, such as the BIOS revision and if a CNA is configured for BFS. It also displays  
the LUN path information to the boot device.  
During startup, you have the option to enter the BIOS configuration utility by pressing Ctrl+E on  
the system console (see Figure 12 (page 17)).  
Figure 12 CNA BIOS  
Figure 13 (page 18) shows the first screen that displays the CNA ports and their respective Port  
WWNs. Use the arrow keys to select a CNA port.  
CNA startup BIOS message  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
Figure 13 CNA select screen  
Figure 14 (page 18) shows the CNA BIOS main menu. On this screen, the CNA firmware and  
BIOS versions display along with the CNA Port WWN, BIOS enablement state, VLAN, and DCBX  
mode. Take note of the code revisions and compare them to the latest supported version for your  
server. This menu is typically used for configuring BFS. In addition to the revision configuration  
information display, Scan for Target Devices is also a useful troubleshooting tool for zoning issues.  
This display is limited and only displays the first LUN for each storage device detected.  
Many parameters and options are available with this utility, but do not change any parameters  
unless instructed by technical support.  
Figure 14 CNA BIOS main menu  
18  
Troubleshooting  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Figure 15 (page 19) shows the CNA BIOS device details.  
Figure 15 CNA BIOS device details  
CNA startup BIOS message  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
4 Support and other resources  
Contacting HP  
For worldwide technical support information, see the HP support website:  
Before contacting HP, collect the following information:  
Product model names and numbers  
Technical support registration number (if applicable)  
Product serial numbers  
Error messages  
Operating system type and revision level  
Detailed questions  
Subscription service  
HP recommends that you register your product at the Subscriber's Choice for Business website:  
After registering, you will receive e-mail notification of product enhancements, new driver versions,  
firmware updates, and other product resources.  
New and changed information in this edition  
The following additions and changes have been made for this edition:  
Added support for CN1100E.  
Updated download links and procedures.  
Related information  
The following documents [and websites] provide related information:  
You can find these documents from the Manuals page of the HP Business Support Center website:  
In the Storage section, click Storage Networking and then select your product.  
HP websites  
For additional information, see the following HP websites:  
20 Support and other resources  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                     
Typographic conventions  
Table 2 Document conventions  
Convention  
Element  
Blue, underlined text: http://www.hp.com  
Bold text  
Cross-reference links and e-mail addresses  
Website addresses  
Keys that are pressed  
Text typed into a GUI element, such as a box  
GUI elements that are clicked or selected, such as menu and  
list items, buttons, tabs, and check boxes  
Italic text  
Text emphasis  
Monospace text  
File and directory names  
System output  
Code  
Commands, their arguments, and argument values  
Monospace, italic text  
Monospace, bold text  
Code variables  
Command variables  
Emphasized monospace text  
WARNING! Indicates that failure to follow directions could result in bodily harm or death.  
CAUTION: Indicates that failure to follow directions could result in damage to equipment or data.  
IMPORTANT: Provides clarifying information or specific instructions.  
NOTE: Provides additional information.  
TIP: Provides helpful hints and shortcuts.  
Customer self repair  
HP customer self repair (CSR) programs allow you to repair your HP storage product. If a CSR part  
needs replacing, HP ships the part directly to you so that you can install it at your convenience.  
Some parts do not qualify for CSR. Your HP-authorized service provider will determine whether a  
repair can be accomplished by CSR.  
For more information about CSR, contact your local service provider, or see the CSR website:  
This product has no customer replaceable components.  
Typographic conventions  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
A Emulex CNA specifications  
This chapter contains the following CNA specifications:  
Environmental specifications  
Table 3 (page 22) lists the CNA environmental specifications.  
Table 3 Environmental specifications  
Environment  
Minimum  
Maximum  
55°C (131°F)  
70°C (158°F)  
85%  
Operating temperature  
Storage temperature  
Relative humidity (non-condensing)  
Airflow  
0°C (32°F)  
–40°C (–40°F)  
5%  
150 lf/min (minimum)  
N/A  
Physical specifications  
Table 4 (page 22) lists the physical specifications.  
Table 4 Physical specifications  
Parameter  
Range  
PICe slot requirements  
Physical dimension  
Minimum eight-lane PCI Express slot  
Low-profile form factor, 6.60 inches by 2.71 inches, and accommodates both the  
full-height and low-profile bracket  
Power requirements  
Agency approvals  
14.5 Watts typical  
Class 1 Laser Product per DHHS 21CFR (J) & EN60825-1  
UL recognized to UL60950-1 2nd Edition  
CUR recognized to CSA 22.2, No. 60950-1-07  
TUV certified by to EN60950-1  
FCC Rules, Part 15, Class A  
Industry Canada, ICES-003, Class A  
EMC Directives 2004/108/EEC (CE Mark)  
EN55022, Class A  
EN55024  
Australian EMC Framework (C-Tick Mark)  
AS/NZS CISPR22:2006 Class A  
Japan VCCI, Class A  
Taiwan BSMI, Class A  
Korea KCC, Class A  
RoHS Compliant (Directive 2002/95/EC)  
China RoHS compliant  
22 Emulex CNA specifications  
Download from Www.Somanuals.com. All Manuals Search And Download.  
               
Emulex CNA media specifications  
The CNA does not ship with cable media. Select either the fiber optic or copper cabling option,  
and purchase the parts separately (see Table 5 (page 23)).  
Table 5 Fiber optic and copper cabling parts  
Media type  
Supported media  
Supported SFP+ optical  
media  
HP BLc 10Gb SR SFP+ (part number 455883-B21)  
Supported copper media for  
connection to B-series  
switches  
HP 1m B-series Active Copper SFP+ Cable (part number AP818A)  
HP 3m B-series Active Copper SFP+ Cable (part number AP819A)  
HP 5m B-series Active Copper SFP+ Cable (part number AP820A)  
Supported copper media for  
connection to C-series  
switches  
HP 3m C-series Passive Copper SFP+ Cable (part number AP784A)  
HP 5m C-series Passive Copper SFP+ Cable (part number AP785A)  
HP 7m C-series Active Copper SFP+ Cable (part number QK701A)  
HP 10m C-series Active Copper SFP+ Cable (part number QK702A)  
Supported copper media for  
connection to HP  
A5820X-14XG-SFP+  
switches  
HP X240 SFP+ SFP+ 0.65 m Direct Attach Cable (part number JD095B)  
HP X240 SFP+ SFP+ 1.2 m Direct Attach Cable (part number JD096B)  
HP X240 SFP+ SFP+ 3 m Direct Attach Cable (part number JD097B)  
CAUTION: Take care not to plug optical cables into cages without transceivers in them.  
NOTE: A CNA does not allow data transmission on either 10 Gb optical or copper link unless  
it is connected to a compatible optical or copper interface connection (that is, multimode to  
multimode). See the appropriate CN switch QuickSpec for the appropriate media supported by  
your switch.  
Emulex CNA media specifications 23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
B Regulatory compliance and safety  
Laser device  
All HP systems equipped with a laser device comply with safety standards, including International  
Electrotechnical Commission (IEC) 825. With specific regard to the laser, the equipment complies  
with laser product performance standards set by government agencies as a Class 1 laser product.  
The product does not emit hazardous light.  
Laser safety warning  
WARNING! To reduce the risk of exposure to hazardous radiation:  
Do not try to open the laser device enclosure. There are no user-serviceable components inside.  
Do not operate controls, make adjustments, or perform procedures to the laser device other  
than those specified in this document.  
Allow only HP-authorized service technicians to repair the laser device.  
Certification and classification information  
This product contains a laser internal to the fiber optic (FO) transceiver for connection to the Fibre  
Channel communications port.  
In the USA, the FO transceiver is certified as a Class 1 laser product conforming to the requirements  
contained in 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser Notice No.  
50, dated June 24, 2007.  
Outside the USA, the FO transceiver is certified as a Class 1 laser product conforming to the  
requirements contained in IEC 825-1:1993 and EN 60825-1:1994, including Amendment 11:1996  
and Amendment 2:2001.  
Laser product label  
The optional label in Figure 16 (page 24) or equivalent may be located on the surface of the  
HP-supplied laser device.  
Figure 16 Class 1 laser product label  
This optional label indicates that the product is classified as a CLASS 1 LASER PRODUCT. This  
label may appear on the laser device installed in your product.  
Notice for North America (FCC & IC)  
FCC Compliance Information Statement  
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two  
conditions: (1) This device may not cause harmful interference, and (2) this device must accept  
any interference received, including interference that may cause undesired operation.  
24 Regulatory compliance and safety  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                         
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital  
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable  
protection against harmful interference when the equipment is operated in a commercial  
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not  
installed and used in accordance with the instruction manual, may cause harmful interference to  
radio communications. Operation of this equipment in a residential area is likely to cause harmful  
interference in which case the user will be required to correct the interference at his own expense.  
Shielded cables must be used between this equipment and attached peripheral devices. The reader  
is cautioned that changes or modifications made to the equipment not expressly approved by  
Emulex could void the user’s authority to operate this equipment. The above statement applies to  
products marketed in the USA.  
International notices and statements  
Canadian notice (avis Canadien)  
Class A equipment  
This class A digital apparatus meets all requirements of the Industry Canada (IC) Interference -  
Causing Equipment Standard (ICES- 003).  
Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel  
brouilleur du Canada. This statement applies to products marketed in Canada.  
European Union regulatory notice  
Products bearing the CE marking comply with the following EU Directives:  
Low Voltage Directive 2006/95/EC  
EMC Directive 2004/108/EC  
Ecodesign Directive 2009/125/EC, where applicable  
CE compliance of this product is valid if powered with the correct CE-marked AC adapter provided  
by HP.  
Compliance with these directives implies conformity to applicable harmonized European standards  
(European Norms) that are listed in the EU Declaration of Conformity issued by HP for this product  
or product family and available (in English only) either within the product documentation or at the  
following website: http://www.hp.eu/certificates (enter the product number in the search field).  
The compliance is indicated by one of the following conformity markings placed on the product:  
For non-telecommunications products and for EU harmonized  
telecommunications products, such as Bluetooth® within  
power class below 10mW.  
For EU non-harmonized telecommunications products (If  
applicable, a 4-digit notified body number is inserted between  
CE and !).  
Please refer to the regulatory label provided on the product. The point of contact for regulatory  
matters is:  
Hewlett-Packard GmbH, Dept./MS: HQ-TRE, Herrenberger Strasse 140, 71034 Boeblingen,  
Germany.  
International notices and statements 25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
Japanese notice  
Korean notice  
26 Regulatory compliance and safety  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Glossary  
This glossary defines acronyms and terms used in this guide and is not a comprehensive  
glossary of computer terms.  
B
BFS  
Boot from SAN.  
C
CN  
Converged Network.  
CNA  
Converged Network Adapter.  
D
DSM  
Device Specific Module.  
Electrostatic discharge.  
E
ESD  
F
FC  
Fibre Channel. A comprehensive set of standards for concurrent communication among servers,  
storage systems, and peripheral devices.  
FCoE  
Fibre Channel over Ethernet protocol.  
Fibre Channel  
A serial data transport infrastructure and protocol used to implement SANs. See also http://  
L
LC  
Lucent connector. An industry-standard connector for fiber optic cable connections.  
Multipath I/O (Microsoft software).  
M
MPIO  
S
SFP  
Small form-factor pluggable transceiver.  
W
WWN  
World Wide Name. A unique identifier assigned to a Fibre Channel device.  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Index  
firmware  
downloading, 11  
installing on Windows, 12  
B
BIOS  
startup message, 17  
G
C
grounding methods, 9  
calculations  
H
MAC address and WWN, 5  
certification and classification information, laser, 24  
Class A equipment, Canadian compliance statement, 25  
CNA  
help  
obtaining, 20  
HP  
installing, 5, 6  
technical support, 20  
isolating problems, 14  
LED states, 16  
media specifications, 23  
observe and collect data, 14  
specifications, 22  
I
IEC EMC, worldwide regulatory compliance notice, 25  
installation  
prerequisites, 5  
startup BIOS message, 17  
CNA Linux drivers  
installing, 12  
collecting data  
installing  
CNA, 5, 6  
CNA drivers on Linux, 12  
drivers, 10  
CNA problems, 14  
contacting HP, 20  
firmware on Linux, 12  
Linux driver kit, 10  
conventions  
multipathing software on Linux, 13  
multipathing software on Windows, 12  
OneCommand Manager utility, 11  
Windows device driver, 11  
Windows Smart Component, 10  
international notices, 25  
isolating  
document, 21  
text symbols, 21  
copper cable option, 23  
copper cables, 23  
customer self repair, 21  
D
CNA problems, 14  
Device Mapper, 11  
document  
J
conventions, 21  
Japan, regulatory compliance notice, 26  
related information, 20  
documentation  
K
HP website, 20  
Korean, regulatory compliance notice, 26  
downloading  
L
firmware, 11  
Linux driver kit, 10  
multipathing software, 11  
OneCommand Manager application kit, 10  
Windows Smart Component, 10  
drivers  
label, laser, 24  
laser  
international certification and classification information,  
product label, 24  
installing, 10  
radiation, warning, 24  
laser device, 24  
E
LED states, 16  
electrostatic discharge, 6, 9  
environmental  
Linux  
installing firmware, 12  
specifications, 22  
European Union, regulatory compliancex09 notice, 25  
installing the OneCommand Manager application kit,  
Linux driver kit  
downloading, 10  
installing, 10  
F
FCC compliance, 24  
fiber optic cable option, 23  
fiber optic cables, 23  
28 Index  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
M
W
MAC address  
warnings, lasers, radiation, 24  
websites  
calculations, 5  
MAC addresses  
recording, 5  
MPIO DSM, 11  
multipathing software  
downloading, 11  
installing on Linux, 13  
installing on Windows, 12  
customer self repair, 21  
HP , 20  
HP Subscriber's Choice for Business, 20  
product manuals, 20  
Windows device driver  
installing, 11  
Windows firmware  
installing, 12  
O
Windows Smart Component  
downloading, 10  
installing, 10  
OneCommand Manager application kit  
downloading, 10  
installing on Linux, 12  
OneCommand Manager utility  
installing, 11  
WWN  
calculations, 5  
recording, 5  
P
physical  
specifications, 22  
prerequisites  
installation, 5  
problems  
isolating, 14  
R
reference numbers  
MAC address, 5  
recording, 5  
regulatory compliance, 24  
notices  
European Union, 25  
IEC EMC statement, worldwide, 25  
Japan, 26  
Korean, 26  
related documentation, 20  
S
safety, 24  
Smart Component kit  
using, 11  
specifications  
CNA, 22  
CNA media, 23  
environmental, 22  
physical, 22  
Subscriber's Choice, HP, 20  
symbols in text, 21  
T
technical support  
HP, 20  
service locator website, 20  
text symbols, 21  
troubleshooting, 14  
typographic conventions, 21  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Haier Microwave Oven MWG7036RW B User Manual
Hans Grohe Plumbing Product 32240XX1 User Manual
Harbor Freight Tools Nail Gun 99640 User Manual
Honeywell Automobile Parts ML6425 User Manual
Hotpoint Double Oven KSO33CX S User Manual
HP Hewlett Packard Electric Heater CH 220 User Manual
HP Hewlett Packard Switch 2012i User Manual
Humminbird Car Video System 531655 1_A User Manual
Husqvarna Brush Cutter 324RX Series User Manual
Image Treadmill IMTL99600 User Manual