TRIANGULAR SANDER
MODEL G9907
INSTRUCTION MANUAL
COPYRIGHT © 2000 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
PRINTED IN CHINA
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
For Your Own Safety Read Instruction Manual
Before Operating This Equipment
The purpose of safety symbols is to attract your attention to possible hazardous
conditions. This manual uses a series of symbols and signal words which are
intended to convey the level of importance of the safety messages. The progres-
sion of symbols is described below. Remember that safety messages by them-
selves do not eliminate danger and are not a substitute for proper accident pre-
vention measures.
Indicates an imminently hazardous situation which, if
not avoided, WILL result in death or serious injury.
Indicates a potentially hazardous situation which, if
not avoided, COULD result in death or serious injury.
Indicates a potentially hazardous situation which, if
not avoided, MAY result in minor or moderate injury.
It may also be used to alert against unsafe practices.
This symbol is used to alert the user to useful information
NOTICE
about proper operation of the equipment.
Safety Instructions For Power Tools
1. KEEP ALL SAFETY DEVICES IN
5. KEEP CHILDREN AND VISITORS
AWAY. All children and visitors
should be kept a safe distance from
work area.
PLACE and in working order.
2. REMOVE ADJUSTING KEYS AND
WRENCHES. Form habit of check-
ing to see that keys and adjusting
wrenches are removed from tool
before turning on.
6. MAKE WORK SHOP CHILD
PROOF with padlocks, master
switches, or by removing starter
keys.
3. KEEP WORK AREA CLEAN.
Cluttered areas and benches invite
accidents.
7. DON’T FORCE TOOL. It will do the
job better and safer at the rate for
which it was designed.
4. DON’T USE IN DANGEROUS
ENVIRONMENT. Don’t use power
tools in damp or wet locations, or
where any flammable or noxious
fumes may exist. Keep work area
well lighted.
8. USE RIGHT TOOL. Don’t force tool
or attachment to do a job for which it
was not designed.
-1-
G9907 Triangular Sander
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Instructions For Power Tools
14. MAINTAIN TOOLS WITH CARE.
Keep tools sharp and clean for
best and safest performance.
Follow instructions for lubricating
and changing accessories.
9. USE PROPER EXTENSION CORD
for the tool. Make sure your exten-
sion cord is in good condition.
Conductor size should be in accor-
dance with the chart below. The
amperage rating should be listed on
the motor or tool nameplate. An
undersized cord will cause a drop in
line voltage resulting in loss of power
and overheating. Your extension
cord must also contain a ground wire
and plug pin. Always repair or
replace extension cords if they
become damaged.
15. DISCONNECT TOOLS before ser-
vicing and changing accessories,
such as blades, bits, cutters, and
the like.
16. REDUCE THE RISK OF UNIN-
TENTIONAL STARTING. Make
sure switch is in off position before
plugging in.
17. USE RECOMMENDED ACCES-
SORIES. Consult the owner’s
manual for recommended acces-
sories. The use of improper acces-
sories may cause risk of injury.
Minimum Gauge for Extension Cords
AMP
RATING
0-6
LENGTH
50ft
16
25ft
18
18
16
14
12
10
100ft
16
14
14
12
18. CHECK DAMAGED PARTS.
Before further use of the tool, a
guard or other part that is dam-
aged should be carefully checked
to determine that it will operate
properly and perform its intended
function. Check for alignment of
moving parts, binding of moving
parts, breakage of parts, mount-
ing, and any other conditions that
may affect its operation. A guard or
other part that is damaged should
be properly repaired or replaced.
7-10
16
16
12
12
11-12
13-16
17-20
21-30
10
No
10
10. WEAR PROPER APPAREL. Do not
wear loose clothing, gloves, neck-
ties, rings, bracelets, or other jewel-
ry which may get caught in moving
parts. Non-slip footwear is recom-
mended. Wear protective hair cover-
ing to contain long hair.
11. ALWAYS USE SAFETY GLASSES.
Also use face or dust mask if cutting
operation is dusty. Everyday eye-
glasses only have impact resistant
lenses, they are NOT safety glass-
es.
No list of safety guidelines can be
complete. Every shop environment
is different. Always consider safety
first, as it applies to your individual
working conditions. Use this and
other machinery with caution and
respect. Failure to do so could result
in serious personal injury, damage
to equipment or poor work results.
12. SECURE WORK. Use clamps or a
vise to hold work when practical. It’s
safer than using your hand and frees
both hands to operate tool.
13. DON’T OVERREACH. Keep proper
footing and balance at all times.
-2-
G9907 Triangular Sander
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Most importantly, we stand behind our
Commentary
tools. If you have any service questions or
parts requests, please call or write us at
the location listed below.
We are proud to offer the Grizzly Model
G9907 Triangular Sander. The Model
G9907 is part of a growing Grizzly family of
fine power tools. When used according to
the guidelines set forth in this manual, you
can expect years of trouble-free, enjoyable
operation and proof of Grizzly’s commit-
ment to customer satisfaction.
Grizzly Industrial, Inc.
2406 Reach Road
Williamsport, PA 17701
Phone: (570) 546-9663
Fax: (800) 438-5901
E-Mail: [email protected]
The Model G9907 Triangular Sander is the
perfect sander for detailed sanding tasks
and hard to reach corners. The pad rotates
at 8,000 orbits per minute with a .040"
eccentric motion for
a
finish without
scratches. Sanding pads have a 61⁄4
square inch surface area, with flow
through holes to direct dust to the 11⁄4" dust
port. Pads are easily changed with the
hook-and-loop attachment system.
To operate this, or any power tool,
safely and efficiently, it is essential to
become as familiar with its character-
istics as possible. The time you invest
before you begin to use your Model
G9907 will be time well spent. DO NOT
operate this machine until you are
competely familiar with the contents of
this manual. Make sure you read and
understand all of the safety proce-
dures. If you do not understand some-
thing, DO NOT operate the machine.
We are pleased to provide this manual
with the Model G9907. It was written to
encourage safety considerations and
guide you through general operating pro-
cedures and maintenance. It represents
our effort to produce the best documenta-
tion possible.
The specifications, details, and pho-
tographs in this manual represent the
Model G9907 as supplied when the manu-
al was prepared. However, owing to
Grizzly’s policy of continuous improve-
ment, changes may be made at any time
with no obligation on the part of Grizzly. If
you have any comments regarding this
manual, please write to us at the address
below:
Grizzly Industrial, Inc.
Technical Documentation
P.O. Box 2069
C
/O
Bellingham, WA 98227-2069
-3-
G9907 Triangular Sander
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION INSTRUCTIONS
Attaching Abrasives
Getting Started
Abrasive sheets are easily attached with
the hook-and-loop system on the pad of
your G9907 sander. Fit the sheet over the
pad so that it covers the entire area, push
and slightly twist to make sure the coated
abrasive sheet is snug on the pad. Make
sure you don’t cover the suction holes.
After making sure the power source
matches the specifications on the sander
label, plug in sander. Push the black
switch (on top of the tool’s handle) forward
to turn it on, and pull the switch back to
turn the sander off. When you first turn it
on, make sure that your finger remains on
the switch so you can STOP the sander in
case there’s a problem. The sander
should run smoothly. Strange or unnatural
noises should be investigated and correct-
ed before operating the machine further.
Remove abrasive sheets by pinching an
edge or corner and peeling off.
Using the Sander
Starting with the coarsest grit you have
determined to be sufficient for the job,
sand the work evenly, in the same direc-
tion as the grain of the wood. Always keep
the machine moving so the finish of your
work stays consistent. If you stay in one
place too long, then the sander may pro-
duce a depression in the wood that will
compromise your finish.
If you cannot easily locate the source of
an unusual noise or vibration, contact our
service department for help.
Selecting Abrasives
The best results from your G9907
Triangular Sander will be accomplished
using the proper grit of coated abrasive.
As a rule, you will want to start with a more
coarse paper for removing large defects or
rough spots, then work through finer grits
one or two grades at a time until you
achieve the smoothness and quality you
desire.
Sanding across the grain of the wood may
be necessary in some cases to remove
rough defects. This should be done with
caution however, because it can produce
cross-grain scratching that will require fur-
ther sanding to remove.
Any time you are unsure about which grit
to begin with, experiment in a small corner
or area that isn’t very noticeable on your
project. Ideally, you want to achieve the
balance of removing defects without dam-
aging your work.
Change abrasive sheets as soon as the
grit becomes dull. You will recognize this
when the sander seems to slide across the
work without any “bite.”
Never apply excessive force while sand-
ing. Your sander will last longer if you let
“it” do the work. Using a slight pressure
barely greater than the weight of the
machine is ideal because you can still
maintain control while obtaining a fine fin-
ish.
ALUMINUM OXIDE and SILICON CAR-
BIDE abrasives are an excellent choice
because they last longer and are sharper
than natural abrasives.
G9907 Triangular Sander
-4-
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
General
Repair and Service
Regular periodic maintenance on your
Model G9907 Triangular Sander will
ensure its optimum performance. Make a
habit of inspecting your sander each time
you use it. Check for the following condi-
tions and repair or replace when neces-
sary:
All quality tools will eventually wear from
normal use. Since sander is encased in a
double insulated plastic cover, leave repair
and service issues to a qualified service
technician. This includes brush replace-
ment, lubrication or any other internal
operation.
1. Loose fasteners.
2. Worn switch.
3. Worn or damaged cords and
plugs.
4. Worn or damaged sanding pad.
5. Any other condition that could
hamper the safe operation of this
machine.
Disassembly and improper reassem-
bly of this device can result in elec-
trical shock danger. Always have this
device serviced by a qualified electri-
cal repair technician. Serious injury
will result.
Keeping Tool Clean
Your G9907 Triangular Sander will give
you years of trouble free service if you
keep it clean and free of built-up dust or
grime. Ensure that no air passages get
blocked. If they do, blow them out with
compressed air. WARNING: Wear safety
glasses when cleaning tool with com-
pressed air.
Plastic parts can easily be cleaned with a
damp cloth, but never use water to clean
any electrical parts. Solvents should also
be avoided on plastic because of the pos-
siblity of damage.
If possible use a scraper to remove glue or
sap from your work; these elements may
hinder the effectiveness of the abrasive
sheets and cause unnecessary build-up of
grime on the sander.
-5-
G9907 Triangular Sander
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY AND RETURNS
Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original
purchaser from the date of purchase. This warranty does not apply to defects due directly
or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of main-
tenance. This is Grizzly’s sole written warranty and any and all warranties that may be
implied by law, including any merchantability or fitness, for any particular purpose, are here-
by limited to the duration of this written warranty. We do not warrant or represent that the
merchandise complies with the provisions of any law or acts unless the manufacturer so
warrants. In no event shall Grizzly’s liability under this warranty exceed the purchase price
paid for the product and any legal actions brought against Grizzly shall be tried in the State
of Washington, County of Whatcom.
We shall in no event be liable for death, injuries to persons or property or for incidental, con-
tingent, special, or consequential damages arising from the use of our products.
To take advantage of this warranty, contact us by mail or phone and give us all the details.
We will then issue you a “Return Number’’, which must be clearly posted on the outside as
well as the inside of the carton. We will not accept any item back without this number. Proof
of purchase must accompany the merchandise.
The manufacturers reserve the right to change specifications at any time because they con-
stantly strive to achieve better quality equipment. We make every effort to ensure that our
products meet high quality and durability standards and we hope you never need to use this
warranty.
Please feel free to write or call us if you have any questions about the machine or the man-
ual.
Grizzly Industrial, Inc.
2406 Reach Road
Williamsport, PA 17701
Phone: (570) 546-9663
Fax: (800) 438-5901
E-Mail:
Thank you again for your business and continued support. We hope to serve you again
soon.
-6-
G9907 Triangular Sander
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY CARD
Name__________________________________________________________
Street__________________________________________________________
City____________________State________Zip_________
Phone Number____________E-Mail___________________FAX____________
MODEL # G9907 Triangular Sander
Order #_______________________
The following information is given on a voluntary basis. It will be used for marketing purposes to help us devel-
op better products and services. Of course, all information is strictly confidential.
9. How many of the machines checked above are
Grizzly? ____________
1. How did you learn about us?
___Advertisement
___Friend
___Catalog
___World Wide Web
___Other__________________________
___Card Deck
10. Which portable/hand held power tools do you own?
Check all that apply.
___Belt Sander
___Biscuit Joiner
___Circular Saw
___Detail Sander
___Drill/Driver
___Orbital Sander
___Palm Sander
___Portable Planer
___Saber Saw
___Reciprocating Saw
___Router
2. What is your annual household income?
___$20,000-$29,999
___$30,000-$39,999
___$40,000-$49,999
___$50,000-$59,999
___$60,000-$69,999
___$70,000-$79,999
___$80,000-$89,999
___$90,000 +
___Miter Saw
___Other_________________________________
3. What is your age group?
___20-29
11. What machines/supplies would you like Grizzly
Industrial to carry?
___50-59
___60-69
___70 +
___30-39
___40-49
___12" Table Saw
___12" Jointer
___Radial Arm Saw
___Panel Saw
___Lumber
___Brass Hardware
4. How long have you been a woodworker?
___Paint & Finishing Supplies
___Contractor’s Supplies
___0 - 2 Years
___2 - 8 Years
___8 - 20 Years
___20+ Years
___Combination Planer/Jointer
___Other_________________________________
5. How would you rank your woodworking skills?
___Simple
___Advanced
___Intermediate
___Master Craftsman
12. What new accessories would you like Grizzly
Industrial to carry?
6. What stationary woodworking tools do you own?
Check all that apply.
___Builders Hardware
___Fasteners
___Hand Tools
___Air Compressor
___Band Saw
___Panel Saw
___Planer
___Wood Components
___Other_________________________________
___Drill Press
___Power Feeder
___Radial Arm Saw
___Shaper
___Jointer
___Lathe
___Drum Sander
___Dust Collector
___Spindle Sander
___Table Saw
13. What other companies do you purchase your tools
and supplies from?
_________________________________________
_________________________________________
_________________________________________
___Mortiser
___Wide Belt Sander
___Horiz.Boring Machine
___Vacuum Veneer Press
14. Do you think your purchase represents good value?
___Other______________________________
___Yes
___No
7. How many of your woodworking machines are
Grizzly? _____________
15. Would you recommend Grizzly to a friend?
___Yes ___No
8. Which benchtop tools do you own? Check all
that apply.
16. Would you allow us to use your name as a refer-
ence for Grizzly customers in your area? Note: We
never use names more than three times.
___1"x42" Belt Sander ___6" - 8" Grinder
___5" - 8" Drill Press ___Mini Lathe
___Yes
___No
___8" Table Saw
___Scroll Saw
___Spindle/Belt Sander ___Mini Jointer
___10"-12"Thickness Planer
___8" - 10" Bandsaw
___Disc/Belt Sander
17.Comments:________________________________
_________________________________________
_________________________________________
_________________________________________
___Other______________________________
Download from Www.Somanuals.com. All Manuals Search And Download.
Send a Grizzly Catalog to a friend:
Name________________________________
Street________________________________
City______________State______Zip_______
FOLD ALONG DOTTED LINE
GRIZZLY INDUSTRIAL, INC.
P.O. BOX 2069
BELLINGHAM, WA 98227-2069
TAPE ALONG EDGES--PLEASE DO NOT STAPLE
Download from Www.Somanuals.com. All Manuals Search And Download.
|