model g0513X2b
17" bandsaW
w/motor braKe
manual insert
the Model g0513X2B is the same as the Model g0513X, except it has a cast iron trunnion, key switch, and
a magnetic brake motor. Besides the data sheet, circuit requirements, certain setup and operation proce-
dures, the wiring diagram, and parts in this insert, the content in the Model g0513X owner's manual is the
same for both machines. on the following pages, the header indicates which page it replaces in the Model
g0513X manual, if applicable.
Before operating your new machine, you Must read and understand this insert and the entire Model
g0513X manual to reduce the risk of injury from improper use or setup.
If you have any questions about this manual insert or the differences between the Model g0513X2B and the
252923
Copyright © MAy, 2008 By grizzly industriAl, inC. revised June, 2011 (Bl)
Warning: no portion of this manual may be reproduced in any shape
or form Without the Written approval of grizzly industrial, inc.
(For Models MAnuFACtured sinCe 5/11) #Bl10777 printed in tAiWAn
Download from Www.Somanuals.com. All Manuals Search And Download.
Blade Information
Standard Blade Length...................................................................................................................... 131-1/2 in.
Blade Width Range................................................................................................................................ 1/8-1 in.
Upper Blade Guides........................................................................................................................ Ball Bearing
Lower Blade Guides........................................................................................................................ Ball Bearing
Table Information
Table Length........................................................................................................................................ 23-5/8 in.
Table Width......................................................................................................................................... 17-1/4 in.
Table Thickness.................................................................................................................................... 1-1/2 in.
Floor to Table Height........................................................................................................................... 37-1/2 in.
Fence Information
Locks in Front............................................................................................................................................... Yes
Locks in Rear................................................................................................................................................. No
Adjustable for Blade Lead............................................................................................................................ Yes
Construction
Table....................................................................................................................... Precision Ground Cast Iron
Rip Fence ............................................................................................................................................ Cast Iron
Body....................................................................................................................... One Piece Reinforced Steel
Upper Wheel....................................................................................................... Computer Balanced Cast Iron
Lower Wheel....................................................................................................... Computer Balanced Cast Iron
Tire................................................................................................................................................ Polyurethane
Wheel Cover ......................................................................................................................... Pre-Formed Steel
Paint........................................................................................................................................... Powder Coated
Other Related Information
Number of Dust Ports....................................................................................................................................... 2
Dust Port Size.............................................................................................................................................. 4 in.
Other Specifications:
Country Of Origin ............................................................................................................................................. Taiwan
Warranty ........................................................................................................................................................... 1 Year
Serial Number Location ...................................................................................................................................... Table
Assembly Time ................................................................................................................................................. 1 Hour
Features:
Cast Iron Table Trunnion
Ball Bearing Blade Guides
Quick Change Blade Release/Tensioner
Micro-Adjusting Gear Table Tilt
Rack & Pinion Upper Blade Guide Height Adjustment
Computer Balanced Cast Iron Wheels with Grizzly Bear Head Cut-Outs
Blade Tension Indicator
Height Scale for Upper Blade Guides
Blade Tracking Window
Hinged Wheel Covers
Deluxe Cast Iron Fence with Extruded Aluminum Resaw Fence Attachment
Included Miter Gauge
Two 4 in. Dust Ports
Motor Stops in Under 3 Seconds After Switch is Turned Off
Included 1/2 in. Blade
-3-
Model g0513X2B (Mfg. since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
(Replaces Section 1 on Page 11)
section 1: safety
For Your Own Safety, Read Instruction
Manual Before Operating this Machine
The purpose of safety symbols is to attract your attention to possible hazardous conditions.
This manual uses a series of symbols and signal words intended to convey the level of impor-
tance of the safety messages. The progression of symbols is described below. Remember that
safety messages by themselves do not eliminate danger and are not a substitute for proper
accident prevention measures.
Indicates an imminently hazardous situation which, if not avoided,
WILL result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided,
COULD result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided,
MAY result in minor or moderate injury. It may also be used to alert
against unsafe practices.
This symbol is used to alert the user to useful information about
proper operation of the machine.
NOTICE
safety instructions for machinery
OWNER’S MANUAL.ꢀ GZVYꢀ VcYꢀ jcYZghiVcYꢀ WEARING PROPER APPAREL.ꢀ 9dꢀ cdiꢀ lZVgꢀ
Xadi]^c\!ꢀ VeeVgZa!ꢀ dgꢀ _ZlZagnꢀ i]Viꢀ XVcꢀ WZXdbZꢀ
ZciVc\aZYꢀ ^cꢀ bdk^c\ꢀ eVgih#ꢀ 6alVnhꢀ i^Zꢀ WVX`ꢀ dgꢀ
XdkZgꢀadc\ꢀ]V^g#ꢀLZVgꢀcdc"ha^eꢀ[ddilZVgꢀidꢀVkd^Yꢀ
VXX^YZciVaꢀha^ehꢀl]^X]ꢀXdjaYꢀXVjhZꢀVꢀadhhꢀd[ꢀldg`"
e^ZXZꢀXdcigda#
i]^hꢀ dlcZg»hꢀ bVcjVaꢀ 7:;DG:ꢀ jh^c\ꢀ bVX]^cZ#ꢀ
JcigV^cZYꢀjhZghꢀXVcꢀWZꢀhZg^djhanꢀ]jgi#
EYE PROTECTION.ꢀ6alVnhꢀlZVgꢀ6CH>"VeegdkZYꢀ
hV[Zinꢀ\aVhhZhꢀdgꢀVꢀ[VXZꢀh]^ZaYꢀl]ZcꢀdeZgVi^c\ꢀdgꢀ
dWhZgk^c\ꢀ bVX]^cZgnꢀ idꢀ gZYjXZꢀ i]Zꢀ g^h`ꢀ d[ꢀ ZnZꢀ
^c_jgnꢀdgꢀWa^cYcZhhꢀ[gdbꢀ[an^c\ꢀeVgi^XaZh#ꢀ:kZgnYVnꢀ
ZnZ\aVhhZhꢀVgZꢀcdiꢀVeegdkZYꢀhV[Zinꢀ\aVhhZh#
HEARING PROTECTION.ꢀ 6alVnhꢀ lZVgꢀ ]ZVg"
^c\ꢀegdiZXi^dcꢀl]ZcꢀdeZgVi^c\ꢀdgꢀdWhZgk^^c\ꢀadjYꢀ
bVX]^cZgn#ꢀ :miZcYZYꢀ ZmedhjgZꢀ idꢀ i]^hꢀ cd^hZꢀ
l^i]djiꢀ]ZVg^c\ꢀegdiZXi^dcꢀXVcꢀXVjhZꢀeZgbVcZciꢀ
]ZVg^c\ꢀadhh#
HAZARDOUS DUST. 9jhiꢀ XgZViZYꢀ l]^aZꢀ jh^c\ꢀ
bVX]^cZgnꢀ bVnꢀ XVjhZꢀ XVcXZg!ꢀ W^gi]ꢀ YZ[ZXih!ꢀ dgꢀ
adc\"iZgbꢀgZhe^gVidgnꢀYVbV\Z#ꢀ7ZꢀVlVgZꢀd[ꢀYjhiꢀ
]VoVgYhꢀVhhdX^ViZYꢀl^i]ꢀZVX]ꢀldg`e^ZXZꢀbViZg^Va!ꢀ
VcYꢀValVnhꢀlZVgꢀVꢀC>DH="VeegdkZYꢀgZhe^gVidgꢀidꢀ
gZYjXZꢀndjgꢀg^h`#
MENTAL ALERTNESS. 7Zꢀ bZciVaanꢀ VaZgiꢀ l]Zcꢀ
gjcc^c\ꢀ bVX]^cZgn#ꢀ CZkZgꢀ deZgViZꢀ jcYZgꢀ i]Zꢀ
^c[ajZcXZꢀd[ꢀYgj\hꢀdgꢀVaXd]da!ꢀl]Zcꢀi^gZY!ꢀdgꢀl]Zcꢀ
Y^higVXiZY#
-4-
Model g0513X2B (Mfg. since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀ
DISCONNECTING POWER SUPPLY.ꢀ6alVnhꢀY^h" FORCING MACHINERY.ꢀ9dꢀcdiꢀ[dgXZꢀbVX]^cZ#ꢀ
XdccZXiꢀ bVX]^cZꢀ [gdbꢀ edlZgꢀ hjeeanꢀ WZ[dgZꢀ hZg" >iꢀl^aaꢀYdꢀi]Zꢀ_dWꢀhV[ZgꢀVcYꢀWZiiZgꢀViꢀi]ZꢀgViZꢀ[dgꢀ
k^X^c\!ꢀ VY_jhi^c\!ꢀ dgꢀ X]Vc\^c\ꢀ Xjii^c\ꢀ iddahꢀ ꢁW^ih!ꢀ l]^X]ꢀ^iꢀlVhꢀYZh^\cZY#
WaVYZh!ꢀXjiiZgh!ꢀZiX#ꢂ#ꢀBV`ZꢀhjgZꢀhl^iX]ꢀ^hꢀ^cꢀD;;ꢀ
edh^i^dcꢀWZ[dgZꢀgZXdccZXi^c\ꢀidꢀVkd^YꢀVcꢀjcZmeZXi"
ZYꢀdgꢀjc^ciZci^dcVaꢀhiVgi#
GUARDS & COVERS.ꢀ <jVgYhꢀ VcYꢀ XdkZghꢀ XVcꢀ
egdiZXiꢀndjꢀ[gdbꢀVXX^YZciVaꢀXdciVXiꢀl^i]ꢀbdk^c\ꢀ
eVgihꢀdgꢀ[an^c\ꢀYZWg^h#ꢀBV`ZꢀhjgZꢀi]ZnꢀVgZꢀ egde"
Zganꢀ^chiVaaZY!ꢀjcYVbV\ZY!ꢀVcYꢀldg`^c\ꢀXdggZXianꢀ
WZ[dgZꢀjh^c\ꢀbVX]^cZ#
APPROVED OPERATION.ꢀ JcigV^cZYꢀ deZgVidghꢀ
XVcꢀ WZꢀ hZg^djhanꢀ ]jgiꢀ Wnꢀ bVX]^cZgn#ꢀ Dcanꢀ Vaadlꢀ
igV^cZYꢀ dgꢀ egdeZganꢀ hjeZgk^hZYꢀ eZdeaZꢀ idꢀ jhZꢀ
bVX]^cZ#ꢀL]ZcꢀbVX]^cZꢀ^hꢀcdiꢀWZ^c\ꢀjhZY!ꢀY^h"
XdccZXiꢀ edlZg!ꢀ gZbdkZꢀ hl^iX]ꢀ `Znh!ꢀ dgꢀ adX`"djiꢀ
bVX]^cZꢀidꢀegZkZciꢀjcVji]dg^oZYꢀjhZ·ZheZX^Vaanꢀ
VgdjcYꢀX]^aYgZc#ꢀBV`Zꢀldg`h]deꢀ`^Yꢀegdd[ꢃ
NEVER STAND ON MACHINE.ꢀHZg^djhꢀ^c_jgnꢀdgꢀ
VXX^YZciVaꢀXdciVXiꢀl^i]ꢀXjii^c\ꢀiddaꢀbVnꢀdXXjgꢀ^[ꢀ
bVX]^cZꢀ^hꢀi^eeZY#ꢀBVX]^cZꢀbVnꢀWZꢀYVbV\ZY#
STABLE MACHINE. JcZmeZXiZYꢀbdkZbZciꢀYjg"
^c\ꢀdeZgVi^dchꢀ\gZVianꢀ^cXgZVhZhꢀi]Zꢀg^h`ꢀd[ꢀ^c_jgnꢀ
VcYꢀ adhhꢀ d[ꢀ Xdcigda#ꢀ KZg^[nꢀ bVX]^cZhꢀ VgZꢀ hiVWaZ$
hZXjgZꢀ VcYꢀ bdW^aZꢀ WVhZhꢀ ꢁ^[ꢀ jhZYꢂꢀ VgZꢀ adX`ZYꢀ
WZ[dgZꢀhiVgi^c\#
DANGEROUS ENVIRONMENTS. 9dꢀ cdiꢀ jhZꢀ
bVX]^cZgnꢀ ^cꢀ lZiꢀ dgꢀ gV^cnꢀ adXVi^dch!ꢀ XajiiZgZYꢀ
VgZVh!ꢀVgdjcYꢀ[aVbbVWaZh!ꢀdgꢀ^cꢀeddgan"a^iꢀVgZVh#ꢀ
@ZZeꢀ ldg`ꢀ VgZVꢀ XaZVc!ꢀ Ygn!ꢀ VcYꢀ lZaa"a^\]iZYꢀ idꢀ
b^c^b^oZꢀg^h`ꢀd[ꢀ^c_jgn#
AWKWARD POSITIONS.ꢀ @ZZeꢀ egdeZgꢀ [ddi^c\ꢀ
VcYꢀWVaVcXZꢀViꢀVaaꢀi^bZhꢀl]ZcꢀdeZgVi^c\ꢀbVX]^cZ#ꢀ
9dꢀcdiꢀdkZggZVX]ꢃꢀ6kd^YꢀVl`lVgYꢀ]VcYꢀedh^i^dchꢀ
i]ViꢀbV`Zꢀldg`e^ZXZꢀXdcigdaꢀY^[[^Xjaiꢀdgꢀ^cXgZVhZꢀ
i]Zꢀg^h`ꢀd[ꢀVXX^YZciVaꢀ^c_jgn#
ONLY USE AS INTENDED.ꢀ Dcanꢀ jhZꢀ bVX]^cZꢀ
[dgꢀ ^ihꢀ ^ciZcYZYꢀ ejgedhZ#ꢀ CZkZgꢀ bdY^[nꢀ dgꢀ VaiZgꢀ
bVX]^cZꢀ[dgꢀVꢀejgedhZꢀcdiꢀ^ciZcYZYꢀWnꢀi]ZꢀbVcj"
[VXijgZgꢀdgꢀhZg^djhꢀ^c_jgnꢀbVnꢀgZhjaiꢃ
USE RECOMMENDED ACCESSORIES.ꢀ8dchjaiꢀ
i]^hꢀdlcZg»hꢀbVcjVaꢀdgꢀi]ZꢀbVcj[VXijgZgꢀ[dgꢀgZX"
dbbZcYZYꢀ VXXZhhdg^Zh#ꢀ Jh^c\ꢀ ^begdeZgꢀ VXXZh"
hdg^Zhꢀl^aaꢀ^cXgZVhZꢀi]Zꢀg^h`ꢀd[ꢀhZg^djhꢀ^c_jgn#
UNATTENDED OPERATION. CZkZgꢀ aZVkZꢀ
bVX]^cZꢀgjcc^c\ꢀl]^aZꢀjcViiZcYZY#ꢀIjgcꢀbVX]^cZꢀ
OFFꢀVcYꢀZchjgZꢀVaaꢀbdk^c\ꢀeVgihꢀXdbeaZiZanꢀhideꢀ
WZ[dgZꢀlVa`^c\ꢀVlVn#
CHILDREN & BYSTANDERS. @ZZeꢀ X]^aYgZcꢀ
VcYꢀWnhiVcYZghꢀVꢀhV[ZꢀY^hiVcXZꢀVlVnꢀ[gdbꢀldg`ꢀ
VgZV#ꢀHideꢀjh^c\ꢀbVX]^cZꢀ^[ꢀX]^aYgZcꢀdgꢀWnhiVcY"
ZghꢀWZXdbZꢀVꢀY^higVXi^dc#
MAINTAIN WITH CARE.ꢀ;daadlꢀVaaꢀbV^ciZcVcXZꢀ
^chigjXi^dchꢀ VcYꢀ ajWg^XVi^dcꢀ hX]ZYjaZhꢀ idꢀ `ZZeꢀ
bVX]^cZꢀ^cꢀ\ddYꢀldg`^c\ꢀXdcY^i^dc#ꢀ6cꢀ^begdeZganꢀ
bV^ciV^cZYꢀbVX]^cZꢀbVnꢀ^cXgZVhZꢀi]Zꢀg^h`ꢀd[ꢀhZg^"
djhꢀ^c_jgn#ꢀ
REMOVE ADJUSTING TOOLS.ꢀ CZkZgꢀ aZVkZꢀ
VY_jhibZciꢀiddah!ꢀX]jX`ꢀ`Znh!ꢀlgZcX]Zh!ꢀZiX#ꢀ^cꢀdgꢀ CHECK DAMAGED PARTS.ꢀ GZ\jaVganꢀ ^cheZXiꢀ
dcꢀbVX]^cZ·ZheZX^VaanꢀcZVgꢀbdk^c\ꢀeVgih#ꢀKZg^[nꢀ bVX]^cZꢀ [dgꢀ YVbV\ZYꢀ eVgih!ꢀ addhZꢀ Wdaih!ꢀ b^h"
VY_jhiZYꢀ dgꢀ b^h"Va^\cZYꢀ eVgih!ꢀ W^cY^c\!ꢀ dgꢀ Vcnꢀ
di]Zgꢀ XdcY^i^dchꢀ i]Viꢀ bVnꢀ V[[ZXiꢀ hV[Zꢀ deZgVi^dc#ꢀ
6alVnhꢀgZeV^gꢀdgꢀgZeaVXZꢀYVbV\ZYꢀdgꢀb^h"VY_jhi"
ZYꢀeVgihꢀWZ[dgZꢀdeZgVi^c\ꢀbVX]^cZ#
gZbdkVaꢀWZ[dgZꢀhiVgi^c\ꢃ
SECURING WORKPIECE.ꢀ L]Zcꢀ gZfj^gZY!ꢀ jhZꢀ
XaVbehꢀdgꢀk^hZhꢀidꢀhZXjgZꢀldg`e^ZXZ#ꢀ6ꢀhZXjgZYꢀ
ldg`e^ZXZꢀegdiZXihꢀ]VcYhꢀVcYꢀ[gZZhꢀWdi]ꢀd[ꢀi]Zbꢀ
idꢀdeZgViZꢀi]ZꢀbVX]^cZ#
EXPERIENCING DIFFICULTIES. >[ꢀ Viꢀ Vcnꢀ i^bZꢀ
ndjꢀ VgZꢀ ZmeZg^ZcX^c\ꢀ Y^[[^Xjai^Zhꢀ eZg[dgb^c\ꢀ i]Zꢀ
^ciZcYZYꢀ deZgVi^dc!ꢀ hideꢀ jh^c\ꢀ i]Zꢀ bVX]^cZꢃꢀ
8dciVXiꢀ djgꢀ IZX]c^XVaꢀ Hjeedgiꢀ 9ZeVgibZciꢀ Viꢀ
ꢁ*,%ꢂꢀ*)+".++(#
FEED DIRECTION.ꢀJcaZhhꢀdi]Zgl^hZꢀcdiZY!ꢀ[ZZYꢀ
ldg`ꢀ V\V^chiꢀ i]Zꢀ gdiVi^dcꢀ d[ꢀ WaVYZhꢀ dgꢀ XjiiZgh#ꢀ
;ZZY^c\ꢀ^cꢀi]ZꢀhVbZꢀY^gZXi^dcꢀd[ꢀgdiVi^dcꢀbVnꢀejaaꢀ
ndjgꢀ]VcYꢀ^cidꢀi]ZꢀXji#
-5-
Model g0513X2B (Mfg. since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
additional safety for bandsaws
blade condition. do not operate with dull, cutting techniQues. plan your operation
cracked or badly worn blade. dull blades require so the blade always cuts to the outside of the
more effort to perform the cut and increase the workpiece. do not back the workpiece away
risk of kickback. inspect blades for cracks and from the blade while the bandsaw is running,
missing teeth before each use.
which could cause kickback and personal injuries.
if you need to back the workpiece out, turn the
hand placement. never position fingers or bandsaw oFF and wait for the blade to come to
hands in line with the blade. if the workpiece or a complete stop. do not twist or put excessive
your hands slip, serious personal injury could stress on the blade that could damage it.
occur.
leaving WorK area. never leave a machine
WorKpiece material. this machine is running unattended. Allow the bandsaw to come
intended for cutting natural and man-made wood to a complete stop and use the padlock to disable
products, and laminate covered wood products. the machine before you leave it unattended.
this machine is not designed to cut metal, glass,
stone, tile, etc.
feed rate. to avoid the risk of the workpiece
slipping and causing operator injury, always feed
blade replacement. to avoid mishaps that stock evenly and smoothly. do not force or twist
could result in operator injury, make sure the blade the blade while cutting, especially when sawing
teeth face down toward the table and the blade is small curves.
properly tensioned and tracked before operating.
small WorKpiece handling. if your hands
blade speed. Moving the workpiece against slip while holding small workpieces with your fin-
a blade that is not at full speed could cause the gers during a cut, amputation or laceration injuries
blade to grab the workpiece and draw the opera- could occur. Always support/feed the workpiece
tor's hands into the blade. Always allow the blade with push sticks, jig, vise, or some type of clamp-
to come to full speed before starting the cut.
ing fixture.
guards. the blade guard protects the operator blade control. to avoid serious personal
from the moving bandsaw blade. only operate injury, do not attempt to stop or slow the blade
this bandsaw with the blade guard in the proper with your hand or the workpiece. Allow the blade
position.
to stop on its own.
no list of safety guidelines can be com-
plete. every shop environment is different.
always consider safety first, as it applies
to your individual working conditions. use
this and other machinery with caution and
respect. failure to do so could result in
serious personal injury, damage to equip-
ment, or poor work results.
like all machinery there is potential danger
when operating this machine. accidents
are frequently caused by lack of familiarity
or failure to pay attention. use this machine
with respect and caution to decrease the
risk of operator injury. if normal safety pre-
cautions are overlooked or ignored, seri-
ous personal injury may occur.
-6-
Model g0513X2B (Mfg. since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
(Replaces Section 2 on Page 14)
section 2: poWer supply
availability
circuit requirements for 220v
I]^hꢀ bVX]^cZꢀ ^hꢀ egZl^gZYꢀ idꢀ deZgViZꢀ dcꢀ Vꢀ ''%Kꢀ
edlZgꢀhjeeanꢀX^gXj^iꢀi]Viꢀ]VhꢀVꢀkZg^[^ZYꢀ\gdjcYꢀVcYꢀ
bZZihꢀi]Zꢀ[daadl^c\ꢀgZfj^gZbZcih/
7Z[dgZꢀ^chiVaa^c\ꢀi]ZꢀbVX]^cZ!ꢀXdch^YZgꢀi]ZꢀVkV^a"
VW^a^inꢀVcYꢀegdm^b^inꢀd[ꢀi]ZꢀgZfj^gZYꢀedlZgꢀhjeeanꢀ
X^gXj^i#ꢀ >[ꢀ Vcꢀ Zm^hi^c\ꢀ X^gXj^iꢀ YdZhꢀ cdiꢀ bZZiꢀ i]Zꢀ
gZfj^gZbZcihꢀ[dgꢀi]^hꢀbVX]^cZ!ꢀVꢀcZlꢀX^gXj^iꢀbjhiꢀ
WZꢀ ^chiVaaZY#ꢀ Idꢀ b^c^b^oZꢀ i]Zꢀ g^h`ꢀ d[ꢀ ZaZXigdXj"
i^dc!ꢀ[^gZ!ꢀdgꢀZfj^ebZciꢀYVbV\Z!ꢀ^chiVaaVi^dcꢀldg`
VcYꢀZaZXig^XVaꢀl^g^c\ꢀbjhiꢀWZꢀYdcZꢀWnꢀVꢀfjVa^[^ZYꢀ
ZaZXig^X^Vcꢀ^cꢀVXXdgYVcXZꢀl^i]ꢀVaaꢀVeea^XVWaZꢀXdYZhꢀ
nominal voltage .............................. 220v/240v
cycle..........................................................60 hz
phase.................................................... 1-phase
circuit rating...................................... 15 amps
plug/receptacle ............................. nema 6-15
cord .........3-Wire, 14 aWg, 300vac, “s”-type
6ꢀ edlZgꢀ hjeeanꢀ X^gXj^iꢀ ^cXajYZhꢀ Vaaꢀ ZaZXig^XVaꢀ
Zfj^ebZciꢀWZilZZcꢀi]ZꢀWgZV`ZgꢀWdmꢀdgꢀ[jhZꢀeVcZa
^cꢀi]ZꢀWj^aY^c\ꢀVcYꢀi]ZꢀbVX]^cZ#ꢀI]ZꢀedlZgꢀhje"
eanꢀX^gXj^iꢀjhZYꢀ[dgꢀi]^hꢀbVX]^cZꢀbjhiꢀWZꢀh^oZYꢀidꢀ
hV[Zanꢀ]VcYaZꢀi]Zꢀ[jaa"adVYꢀXjggZciꢀYgVlcꢀ[gdbꢀi]Zꢀ
bVX]^cZꢀ [dgꢀ Vcꢀ ZmiZcYZYꢀ eZg^dYꢀ d[ꢀ i^bZ#ꢀ ꢁ>[ꢀ i]^hꢀ
bVX]^cZꢀ ^hꢀ XdccZXiZYꢀ idꢀ Vꢀ X^gXj^iꢀ egdiZXiZYꢀ Wnꢀ
[jhZh!ꢀjhZꢀVꢀi^bZꢀYZaVnꢀ[jhZꢀbVg`ZYꢀ9#ꢂ
Electrocution, fire, or
equipment damage may
occur if machine is not
correctly grounded and
connected to the power
supply.
full-load current rating
I]Zꢀ [jaa"adVYꢀ XjggZciꢀ gVi^c\ꢀ ^hꢀ i]Zꢀ VbeZgV\Zꢀ Vꢀ
bVX]^cZꢀYgVlhꢀViꢀ&%%ꢁꢀd[ꢀi]ZꢀgViZYꢀdjiejiꢀedlZg#ꢀ
Dcꢀ bVX]^cZhꢀ l^i]ꢀ bjai^eaZꢀ bdidgh!ꢀ i]^hꢀ ^hꢀ i]Zꢀ
VbeZgV\ZꢀYgVlcꢀWnꢀi]ZꢀaVg\Zhiꢀbdidgꢀdgꢀhjbꢀd[ꢀVaaꢀ
bdidghꢀVcYꢀZaZXig^XVaꢀYZk^XZhꢀi]Viꢀb^\]iꢀdeZgViZꢀ
ViꢀdcZꢀi^bZꢀYjg^c\ꢀcdgbVaꢀdeZgVi^dch#
For your own safety and protection of
property, consult a qualified electrician if
you are unsure about wiring practices or
electrical codes in your area.
Note: The circuit requirements listed in this man-
ual apply to a dedicated circuit—where only one
machine will be running at a time. If this machine
will be connected to a shared circuit where mul-
tiple machines will be running at the same time,
consult a qualified electrician to ensure that the
circuit is properly sized for safe operation.
full-load current rating at 220v .... 8.7 amps
I]Zꢀ[jaa"adVYꢀXjggZciꢀ^hꢀcdiꢀi]ZꢀbVm^bjbꢀVbdjciꢀ
d[ꢀVbehꢀi]Viꢀi]ZꢀbVX]^cZꢀl^aaꢀYgVl#ꢀ>[ꢀi]ZꢀbVX]^cZꢀ
^hꢀdkZgadVYZY!ꢀ^iꢀl^aaꢀYgVlꢀVYY^i^dcVaꢀVbehꢀWZndcYꢀ
i]Zꢀ[jaa"adVYꢀgVi^c\#
>[ꢀi]ZꢀbVX]^cZꢀ^hꢀdkZgadVYZYꢀ[dgꢀVꢀhj[[^X^ZciꢀaZc\i]ꢀ
d[ꢀi^bZ!ꢀYVbV\Z!ꢀdkZg]ZVi^c\!ꢀdgꢀ[^gZꢀbVnꢀgZhjai·
ZheZX^Vaanꢀ ^[ꢀ XdccZXiZYꢀ idꢀ Vcꢀ jcYZgh^oZYꢀ X^gXj^i#ꢀ
IdꢀgZYjXZꢀi]Zꢀg^h`ꢀd[ꢀi]ZhZꢀ]VoVgYh!ꢀVkd^YꢀdkZg"
adVY^c\ꢀi]ZꢀbVX]^cZꢀYjg^c\ꢀdeZgVi^dcꢀVcYꢀbV`Zꢀ
hjgZꢀ^iꢀ^hꢀXdccZXiZYꢀidꢀVꢀedlZgꢀhjeeanꢀX^gXj^iꢀi]Viꢀ
bZZihꢀi]ZꢀgZfj^gZbZcihꢀ^cꢀi]Zꢀ[daadl^c\ꢀhZXi^dc#
-7-
Model g0513X2B (Mfg. since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
grounding instructions
I]^hꢀ bVX]^cZꢀ BJHIꢀ WZꢀ \gdjcYZY#ꢀ >cꢀ i]Zꢀ ZkZci
d[ꢀXZgiV^cꢀbVa[jcXi^dchꢀdgꢀWgZV`Ydlch!ꢀ\gdjcY^c\
gZYjXZhꢀi]Zꢀg^h`ꢀd[ꢀZaZXig^Xꢀh]dX`ꢀWnꢀegdk^Y^c\ꢀV
eVi]ꢀd[ꢀaZVhiꢀgZh^hiVcXZꢀ[dgꢀZaZXig^XꢀXjggZci#
Serious injury could occur if you connect
the machine to power before completing the
setup process. DO NOT connect to power
until instructed later in this manual.
I]ZꢀedlZgꢀXdgYꢀVcYꢀeaj\ꢀheZX^[^ZYꢀjcYZgꢀ¸8^gXj^iꢀ
GZfj^gZbZcihꢀ [dgꢀ ''%K¹ꢀ dcꢀ i]Zꢀ egZk^djhꢀ eV\Zꢀ
]VhꢀVcꢀZfj^ebZci"\gdjcY^c\ꢀl^gZꢀVcYꢀVꢀ\gdjcY"
^c\ꢀ egdc\#ꢀ I]Zꢀ eaj\ꢀ bjhiꢀ dcanꢀ WZꢀ ^chZgiZYꢀ ^cidꢀ
Vꢀ bViX]^c\ꢀ gZXZeiVXaZꢀ ꢁdjiaZiꢂꢀ i]Viꢀ ^hꢀ egdeZganꢀ
^chiVaaZYꢀ VcYꢀ \gdjcYZYꢀ ^cꢀ VXXdgYVcXZꢀ l^i]ꢀ Vaaꢀ
adXVaꢀXdYZhꢀVcYꢀdgY^cVcXZhꢀꢁhZZꢀ[^\jgZꢀWZadlꢂ#
>begdeZgꢀXdccZXi^dcꢀd[ꢀi]ZꢀZfj^ebZci"\gdjcY^c\ꢀ
l^gZꢀ XVcꢀ gZhjaiꢀ ^cꢀ Vꢀ g^h`ꢀ d[ꢀ ZaZXig^Xꢀ h]dX`#ꢀ I]Zꢀ
l^gZꢀl^i]ꢀ\gZZcꢀ^chjaVi^dcꢀꢁl^i]ꢀdgꢀl^i]djiꢀnZaadlꢀ
hig^eZhꢂꢀ^hꢀi]ZꢀZfj^ebZci"\gdjcY^c\ꢀl^gZ#ꢀ>[ꢀgZeV^gꢀ
dgꢀgZeaVXZbZciꢀd[ꢀi]ZꢀedlZgꢀXdgYꢀdgꢀeaj\ꢀ^hꢀcZX"
ZhhVgn!ꢀYdꢀcdiꢀXdccZXiꢀi]ZꢀZfj^ebZci"\gdjcY^c\ꢀ
l^gZꢀidꢀVꢀa^kZꢀꢁXjggZciꢀXVggn^c\ꢂꢀiZgb^cVa#
ꢀ
8]ZX`ꢀl^i]ꢀVꢀfjVa^[^ZYꢀZaZXig^X^VcꢀdgꢀhZgk^XZꢀeZg"
hdccZaꢀ^[ꢀndjꢀYdꢀcdiꢀjcYZghiVcYꢀi]ZhZꢀ\gdjcY^c\ꢀ
gZfj^gZbZcih!ꢀdgꢀ^[ꢀndjꢀVgZꢀ^cꢀYdjWiꢀVWdjiꢀl]Zi]Zgꢀ
i]Zꢀiddaꢀ^hꢀegdeZganꢀ\gdjcYZY#ꢀ>[ꢀndjꢀZkZgꢀcdi^XZꢀ
i]ViꢀVꢀXdgYꢀdgꢀeaj\ꢀ^hꢀYVbV\ZYꢀdgꢀldgc!ꢀY^hXdc"
cZXiꢀ^iꢀ[gdbꢀedlZg!ꢀVcYꢀ^bbZY^ViZanꢀgZeaVXZꢀ^iꢀl^i]ꢀ
VꢀcZlꢀdcZ#
GROUNDED
6-15 RECEPTACLE
8jggZciꢀ8Vggn^c\ꢀEgdc\h
6-15 PLUG
<gdjcY^c\ꢀEgdc\
extension cords
LZꢀYdꢀcdiꢀgZXdbbZcYꢀjh^c\ꢀVcꢀZmiZch^dcꢀXdgYꢀ
l^i]ꢀi]^hꢀbVX]^cZ#ꢀ>[ꢀndjꢀbjhiꢀjhZꢀVcꢀZmiZch^dcꢀ
XdgY!ꢀdcanꢀjhZꢀ^iꢀ^[ꢀVWhdajiZanꢀcZXZhhVgnꢀVcYꢀdcanꢀ
dcꢀVꢀiZbedgVgnꢀWVh^h#
figure 1. typical 6-15 plug and receptacle.
:miZch^dcꢀXdgYhꢀXVjhZꢀkdaiV\ZꢀYgde!ꢀl]^X]ꢀbVnꢀ
YVbV\ZꢀZaZXig^XVaꢀXdbedcZcihꢀVcYꢀh]dgiZcꢀbdidgꢀ
a^[Z#ꢀKdaiV\ZꢀYgdeꢀ^cXgZVhZhꢀVhꢀi]ZꢀZmiZch^dcꢀXdgYꢀ
h^oZꢀ\Zihꢀadc\ZgꢀVcYꢀi]Zꢀ\Vj\Zꢀh^oZꢀ\ZihꢀhbVaaZgꢀ
ꢁ]^\]Zgꢀ\Vj\ZꢀcjbWZghꢀ^cY^XViZꢀhbVaaZgꢀh^oZhꢂ#
6cnꢀZmiZch^dcꢀXdgYꢀjhZYꢀl^i]ꢀi]^hꢀbVX]^cZꢀbjhiꢀ
XdciV^cꢀ Vꢀ \gdjcYꢀ l^gZ!ꢀ bViX]ꢀ i]Zꢀ gZfj^gZYꢀ eaj\ꢀ
VcYꢀ gZXZeiVXaZ!ꢀ VcYꢀ bZZiꢀ i]Zꢀ [daadl^c\ꢀ gZfj^gZ"
bZcih/
No adapter should be used with the
required plug. If the plug does not fit the
available receptacle, or the machine must
be reconnected for use on a different type
of circuit, the reconnection must be made
by a qualified electrician and comply with all
local codes and ordinances.
minimum gauge size ...........................14 aWg
maximum length (shorter is better).......50 ft.
-8-
Model g0513X2B (Mfg. since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
hardware and tools:
Qty
(Replaces Inventory
on Page 17)
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
eye Bolt M10-1.5 (may be installed)........... 1
hex Bolts M8-1.25 x 25 (table).................. 4
Flat Washers 8mm (table, Fence, rail)..... 8
lock Washers 8mm (table, rail)............... 5
lock Washers 6mm (rail).......................... 3
Flat Washers 6mm (rail)............................ 3
Cap screws M6-1 x 20 (rail) ..................... 3
Cap screw M8-1.25 x 20 (rail) .................. 1
Knobs M8-1.25 x 20 (rail).......................... 2
hex Bolt M8-1.25 x 90 (pos. stop)............. 1
hex nuts M8-1.25 (pos. stop, Fence)........ 2
lock handle M8-1.25 x 44 (Fence)............ 1
Moving plate (Fence).................................. 1
table pin..................................................... 1
rail plates ................................................. 3
hex Wrench 5mm & 8mm.....................1 ea
open end Wrench 10 x 13mm................... 1
I]Zꢀ[daadl^c\ꢀ^hꢀVꢀYZhXg^ei^dcꢀd[ꢀi]ZꢀbV^cꢀXdbed"
cZcihꢀh]^eeZYꢀl^i]ꢀndjgꢀbVX]^cZ#ꢀAVnꢀi]ZꢀXdbed"
cZcihꢀdjiꢀidꢀ^ckZcidgnꢀi]Zb#
>[ꢀ Vcnꢀ cdc"egdeg^ZiVgnꢀ eVgihꢀ VgZꢀ b^hh^c\ꢀ ꢁZ#\#ꢀ Vꢀ
cjiꢀdgꢀVꢀlVh]Zgꢂ!ꢀlZꢀl^aaꢀ\aVYanꢀgZeaVXZꢀi]Zb0ꢀdgꢀ
[dgꢀi]ZꢀhV`Zꢀd[ꢀZmeZY^ZcXn!ꢀgZeaVXZbZcihꢀXVcꢀWZꢀ
dWiV^cZYꢀViꢀndjgꢀadXVaꢀ]VgYlVgZꢀhidgZ#
crate contents (figure 2):
Qty
a. Bandsaw (not shown)................................. 1
b. table w/table insert ................................... 1
c. Miter gauge................................................ 1
d. resaw Fence ............................................. 1
e. Front square rail ...................................... 1
f. Fence Assembly......................................... 1
g. guide post handwheel............................... 1
NOTICE
If you cannot find an item on this list, check
the mounting location on the machine or the
packaging materials. Sometimes parts are
pre-installed for shipping, or they become
hidden by packaging materials.
B
C
d
g
e
F
figure 2. g0513X2B inventory.
-9-
Model g0513X2B (Mfg. since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
(Replaces Table on (Replaces Installing
Page 21)
Fence on Page 25)
components and hardware needed:
hex Bolts M8-1.25 x 25 .................................... 4
Qty
components and hardware needed:
Qty
Fence Assembly................................................ 1
Front rail .......................................................... 1
rail plates ......................................................... 3
Cap screws M6-1 x 20...................................... 3
Flat Washers 6mm ............................................ 3
lock Washers 6mm........................................... 3
Cap screw M8-1.25 x 20................................... 1
Knobs M8-1.25 x 20 .......................................... 2
Flat Washers 8mm ............................................ 4
lock Washer 8mm ............................................ 1
resaw Fence..................................................... 1
lock handle M8-1.25 x 44 ................................ 1
Moving plate...................................................... 1
1. Follow steps 1-3 on page 21 in the g0513X
Manual. if the table insert is pre-installed,
remove it now.
2. With the help of another person, lift the table
onto the trunnions.
3. secure the table to the trunnions with the four
M8-1.25 x 25 hex bolts, 8mm lock washers
and 8mm flat washers.
4. Follow steps 6-9 in the g0513X Manual.
to install the fence:
1. Attach the rail plates to the front rail with the
three M6-1 x 20 cap screws, 6mm lock wash-
ers, and 6mm flat washers (see figure 3).
(Replaces Positive
Stop on Page 23)
Front rail
rail plate
components and hardware needed:
hex Bolts M8-1.25 x 90 .................................... 1
hex nut M8-1.25................................................ 1
Qty
Flat Washer 6mm
Flat
to install the positive stop:
Washer
8mm
lock Washer 6mm
1. unlock the table tilt lock lever, tilt the table to
access the positive stop bolt installation loca-
tion, then lock the lever.
Cap screw
M6-1 x 20
Knob
Cap screw
M8-1.25 x 20
lock Washer
8mm
2. thread the M8-1.25 hex nut halfway onto the
M8-1.25 x 90 hex bolt (this is the positive stop
bolt).
figure 3. installing front rail onto table.
3. thread the positive stop bolt into the thread-
ed hole on the bandsaw body.
2. Attach the outer two rail plates with the round
and elongated mounting holes on the outer
part of the table bottom with two M8-1.25 x
20 knobs and 8mm flat washers. Attach the
remaining rail plate with the round mounting
holes using an M8-1.25 x 20 cap screw, 8mm
lock washer and 8mm flat washer (figure
3).
4. lower the table onto the positive stop bolt.
5. Follow to set the positive stop on g0513X
Manual page 24.
-10-
Model g0513X2B (Mfg. since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
3. thread the fence handle into the fence, then
tighten the hex nut against the fence pivot
block (see figure 4).
power connection
6[iZgꢀ ndjꢀ ]VkZꢀ XdbeaZiZYꢀ Vaaꢀ egZk^djhꢀ hZijeꢀ
^chigjXi^dchꢀVcYꢀX^gXj^iꢀgZfj^gZbZcih!ꢀi]ZꢀbVX]^cZꢀ
^hꢀgZVYnꢀidꢀWZꢀXdccZXiZYꢀidꢀi]ZꢀedlZgꢀhjeean#
pivot Block
Idꢀ Vkd^Yꢀ jcZmeZXiZYꢀ hiVgijehꢀ dgꢀ egdeZginꢀ YVb"
V\Z!ꢀjhZꢀi]Zꢀ[daadl^c\ꢀhiZehꢀl]ZcZkZgꢀXdccZXi^c\ꢀ
dgꢀY^hXdccZXi^c\ꢀi]ZꢀbVX]^cZ#
Fence
handle
hex nut
connecting power
1.ꢀ Ijgcꢀi]ZꢀbVX]^cZꢀedlZgꢀhl^iX]ꢀOFF#
figure 4. Fence handle components.
2.ꢀ >chZgiꢀ i]Zꢀ edlZgꢀ XdgYꢀ eaj\ꢀ ^cidꢀ Vꢀ bViX]^c\
edlZgꢀ hjeeanꢀ gZXZeiVXaZ#ꢀ I]Zꢀ bVX]^cZꢀ ^hꢀ
cdlꢀXdccZXiZYꢀidꢀi]ZꢀedlZgꢀhdjgXZ#
4. install the resaw fence lock handle (with the
washer and moving plate) onto the fence,
then slide the resaw fence over the moving
plate as shown in figure 5.
note: Leave the moving plate and lock han-
dle loose enough to slide on the fence.
resaw Fence
resaw lock
handle
figure 6. Connecting power.
Moving
plate
disconnecting power
1.ꢀ Ijgcꢀi]ZꢀbVX]^cZꢀedlZgꢀhl^iX]ꢀOFF#
figure 5. Attaching resaw fence to standard
fence.
2.ꢀ <gVheꢀi]ZꢀbdaYZYꢀeaj\ꢀVcYꢀejaaꢀ^iꢀXdbeaZiZanꢀ
djiꢀd[ꢀi]ZꢀgZXZeiVXaZ#ꢀ9dꢀcdiꢀejaaꢀWnꢀi]ZꢀXdgY
Vhꢀi]^hꢀbVnꢀYVbV\Zꢀi]Zꢀl^gZhꢀ^ch^YZ#
5. tighten the resaw lock handle.
6. pull the fence handle up and place the fence
assembly on the rail.
7. push the fence handle down to lock the fence
assembly in place.
guide post
handwheel
secure the guide post handwheel onto the flat
part of the handwheel shaft with the M6-1 x 20
cap screw.
figure 7. Disconnecting power.
-11-
Model g0513X2B (Mfg. since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Without resetting the oFF button, press
the on button. the machine should not
start.
(Replaces Test Run
on Page 21)
—if the machine does not start, the oFF but-
ton safety feature is working correctly.
to test run the machine:
—if the machine does start (with the stop
button pushed in), immediately disconnect
power to the machine. the oFF button
safety feature is not working correctly. this
safety feature must work properly before
proceeding with regular operations. Call
tech support for help.
1. Follow steps 1-5 on g0513X Manual page
26.
2. verify that the machine is operating correctly
by turning the switch disabling key (figure 8)
to "1" and turning the machine ON.
—When operating correctly, the machine
runs smoothly with little or no vibration or
rubbing noises.
5. twist the oFF button clockwise so it pops
out. When the oFF button pops out, the
switch is reset and ready for operation (see
figure 9).
—investigate and correct strange or unusual
noises or vibrations before operating the
machine further. Always disconnect the
machine from power when investigating or
correcting potential problems.
OFF Button
figure 9. resetting the switch.
6. turn the switch disabling key to "0", as shown
in figure 8.
7. try to turn the machine ON.
—if the bandsaw does not start, the switch
disabling feature is working as designed.
the test run is complete.
figure 8. g0513X2 switch disabling key and
on/oFF switch.
—if the bandsaw starts, immediately discon-
nect power. the switch disabling feature is
not working correctly. this safety feature
must work properly before proceeding with
regular operations. Call tech support for
help.
3. press the oFF button to stop the machine.
motor brake
the motor brake is activated automatically when
the oFF button is pushed.
-12-
Model g0513X2B (Mfg. since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
(Replaces Aligning
Fence on Page 31)
NOTICE
adjusting the fence parallel to the miter slot
does not guarantee straight cuts. the miter
slot may need to be adjusted parallel to the
side of the blade. refer to the "aligning
table" instructions on g0513X manual page
30.
to ensure cutting accuracy when the fence is first
installed, the fence should be aligned with the
miter slot.
to align the fence parallel with the miter slot:
1. disConneCt BAndsAW FroM poWer!
disabling & locking
switch
2. Make sure the miter slot is aligned with the
bandsaw blade (refer to aligning table on
g0513X Manual page 30).
I]ZꢀedlZgꢀhl^iX]ꢀXVcꢀWZꢀY^hVWaZYꢀVcYꢀadX`ZYꢀWnꢀ
gZbdk^c\ꢀi]Zꢀ`Zn!ꢀVhꢀh]dlc#ꢀAdX`^c\ꢀi]Zꢀhl^iX]ꢀ
^cꢀ i]^hꢀ bVccZgꢀ XVcꢀ egZkZciꢀ jcVji]dg^oZYꢀ deZgV"
i^dcꢀd[ꢀi]ZꢀbVX]^cZ!ꢀl]^X]ꢀ^hꢀZheZX^Vaanꢀ^bedgiVciꢀ
^[ꢀ i]Zꢀ bVX]^cZꢀ ^hꢀ cdiꢀ hidgZYꢀ ^ch^YZꢀ Vcꢀ VXXZhh"
gZhig^XiZYꢀWj^aY^c\#
3. if the fence is mounted on the left-hand side
of the blade, remove it and remount it next to
the miter slot.
4. loosen the knobs and cap screw that secure
the fence rail to the table (see figure 3 on
page 10).
IMPORTANT:ꢀ AdX`^c\ꢀ i]Zꢀ edlZgꢀ hl^iX]ꢀ l^i]ꢀ Vꢀ
`ZnꢀdcanꢀgZhig^Xihꢀ^ihꢀ[jcXi^dc#ꢀ>iꢀ^hꢀcdiꢀVꢀhjWhi^ijiZꢀ
[dgꢀY^hXdccZXi^c\ꢀedlZgꢀ[gdbꢀi]ZꢀbVX]^cZꢀl]Zcꢀ
VY_jhi^c\ꢀdgꢀhZgk^X^c\#
5. Adjust the fence face parallel with the edge of
the miter slot, as shown in figure 10.
POWER
0
I
figure 10. example of fence square with miter
slot.
Children or untrained people can be killed
or seriously injured by this machine. This
risk increases with unsupervised operation.
To help prevent unsupervised operation,
remove the key from the switch before
leaving machine unattended! Place key in a
well-hidden or secure location.
6. tighten the knobs and cap screw that secure
the rail to the table, being careful not to move
the fence.
-13-
Model g0513X2B (Mfg. since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
3. loosen the pointer adjustment nut (figure
12) and set the pointer in line with "0" and the
measurement scale on the table.
pointer calibration
your new bandsaw is equipped with a fence mea-
surement system that includes a fence pointer,
which must be calibrated when the bandsaw is
first set up.
pointer nut
pointer
to calibrate the pointer:
1. if the fence is mounted on the right-hand side
of the blade, remove it and re-install it on the
left-hand side of the blade.
2. place the fence flush against the bandsaw
blade (figure 11).
figure 12. Calibrating fence pointer (screw out
of view).
4. re-tighten the pointer adjustment nut.
figure 11. Fence flush with blade.
-14-
Model g0513X2B (Mfg. since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
to lubricate the tension adjustment assem-
bly:
(Replaces
Lubrication on Page
45)
1. disConneCt BAndsAW FroM poWer!
2. open the top wheel cover and look through
the top of the wheel.
to lubricate the blade guide rack and pinion:
1. disConneCt BAndsAW FroM poWer!
3. Wipe off any existing grease and sawdust
buildup on the blade tension adjustment
assembly and tension lever cam.
2. lower the blade guide until it reaches the
table.
4. Apply a thin coat of grease to the tension
adjustment assembly and tension lever cam
(see figure 14).
3. Wipe off any existing grease and sawdust
buildup on the rack (see figure 13).
tension
lever Cam
rack
tension
Adjustment
Assembly
figure 14. tension adjustment assembly
locations (top wheel removed for clarity).
figure 13. rack lubrication location.
to lubricate the trunnions:
4. Apply a thin coat of light all-purpose grease to
the rack.
1. disConneCt BAndsAW FroM poWer!
5. Move the blade guide up and down several
times to distribute the grease, then remove
any excess grease to help prevent sawdust
buildup.
2. Move the table up until it reaches its maximum
45˚ angle and wipe off all excess grease and
sawdust from the trunnions.
3. Apply a thin coat of light all purpose grease to
the trunnions (see figure 15).
to lubricate the blade tracking knob:
1. disConneCt BAndsAW FroM poWer!
2. loosen the blade tracking lock lever, then
unscrew the blade tracking knob 5 turns.
3. Wipe off any existing grease and sawdust
buildup on the threads.
4. Apply a few dabs of a light all-purpose grease
to the threads.
figure 15. trunnion lubrication location.
5. re-adjust tracking (see blade tracking on
g0513X Manual page 22).
4. Move the table down and up to distribute the
grease, then wipe off any excess grease.
-15-
Model g0513X2B (Mfg. since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
magnetic brake
adjustment
on
off
Brake
shoe
the space between the magnetic motor brake
and brake shoe is preset by the factory at 0.2mm.
however, you should adjust this space every two
to three years, or when it takes over five seconds
for the brake to stop the motor.
Cap
screw
Magnetic
Brake
tools needed
Motor
Fan
phillips head screwdriver.................................. 1
us dollar Bills ................................................... 2
hex Wrench 3mm.............................................. 1
hex Wrench 4mm.............................................. 1
figure 16. Adjusting distance between magnetic
brake and brake shoe.
3. Fold two dollar bills in half and slide them
between the brake shoe and magnetic brake
on either side (see figure 16). the space
between the brake and shoe is correctly set
when there is just enough tension to allow
you to slide the dollar bills out.
to adjust the space between the magnetic
brake and brake shoe:
1. disConneCt BAndsAW FroM poWer!
2. remove the motor fan cover, then loosen the
cap screws securing the motor fan and brake
shoe (see figure 16).
4. tighten the cap screws on the motor fan,
then re-install the fan cover.
-16-
Model g0513X2B (Mfg. since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
section 8: Wiring
I]ZhZꢀeV\ZhꢀVgZꢀXjggZciꢀViꢀi]Zꢀi^bZꢀd[ꢀeg^ci^c\#ꢀ=dlZkZg!ꢀ^cꢀi]Zꢀhe^g^iꢀd[ꢀ^begdkZbZci!ꢀlZꢀbVnꢀbV`ZꢀX]Vc\"
Zhꢀidꢀi]ZꢀZaZXig^XVaꢀhnhiZbhꢀd[ꢀ[jijgZꢀbVX]^cZh#ꢀ8dbeVgZꢀi]ZꢀbVcj[VXijgZꢀYViZꢀd[ꢀndjgꢀbVX]^cZꢀidꢀi]ZꢀdcZ
hiViZYꢀ^cꢀi]^hꢀbVcjVa!ꢀVcYꢀhijYnꢀi]^hꢀhZXi^dcꢀXVgZ[jaan#
>[ꢀi]ZgZꢀVgZꢀY^[[ZgZcXZhꢀWZilZZcꢀndjgꢀbVX]^cZꢀVcYꢀl]Viꢀ^hꢀh]dlcꢀ^cꢀi]^hꢀhZXi^dc!ꢀXVaaꢀIZX]c^XVaꢀHjeedgiꢀVi
ꢁ*,%ꢂꢀ*)+".++(ꢀ[dgꢀVhh^hiVcXZꢀ7:;DG:ꢀbV`^c\ꢀVcnꢀX]Vc\Zhꢀidꢀi]Zꢀl^g^c\ꢀdcꢀndjgꢀbVX]^cZ#ꢀ6cꢀjeYViZY
l^g^c\ꢀY^V\gVbꢀbVnꢀWZꢀVkV^aVWaZ#ꢀNote:ꢀPlease gather the serial number and manufacture date of your
machine before calling. This information can be found on the main machine label.
Wiring safety instructions
SHOCK HAZARD. Ldg`^c\ꢀdcꢀl^g^c\ꢀi]Viꢀ^hꢀXdc" WIRE/COMPONENT DAMAGE.ꢀ9VbV\ZYꢀl^gZhꢀ
cZXiZYꢀidꢀVꢀedlZgꢀhdjgXZꢀ^hꢀZmigZbZanꢀYVc\Zgdjh#ꢀ dgꢀ XdbedcZcihꢀ ^cXgZVhZꢀ i]Zꢀ g^h`ꢀ d[ꢀ hZg^djhꢀ eZg"
IdjX]^c\ꢀ ZaZXig^[^ZYꢀ eVgihꢀ l^aaꢀ gZhjaiꢀ ^cꢀ eZghdcVaꢀ hdcVaꢀ^c_jgn!ꢀ[^gZ!ꢀdgꢀbVX]^cZꢀYVbV\Z#ꢀ>[ꢀndjꢀcdi^XZꢀ
^c_jgnꢀ ^cXajY^c\ꢀ Wjiꢀ cdiꢀ a^b^iZYꢀ idꢀ hZkZgZꢀ Wjgch!ꢀ i]ViꢀVcnꢀl^gZhꢀdgꢀXdbedcZcihꢀVgZꢀYVbV\ZYꢀl]^aZꢀ
ZaZXigdXji^dc!ꢀ dgꢀ YZVi]#ꢀ 9^hXdccZXiꢀ i]Zꢀ edlZgꢀ eZg[dgb^c\ꢀVꢀl^g^c\ꢀiVh`!ꢀgZeaVXZꢀi]dhZꢀl^gZhꢀdgꢀ
[gdbꢀi]ZꢀbVX]^cZꢀWZ[dgZꢀhZgk^X^c\ꢀZaZXig^XVaꢀXdb" XdbedcZcih#
edcZcihꢁ
MOTOR WIRING. I]Zꢀ bdidgꢀ l^g^c\ꢀ h]dlcꢀ ^cꢀ
MODIFICATIONS.ꢀ BdY^[n^c\ꢀ i]Zꢀ l^g^c\ꢀ WZndcYꢀ i]ZhZꢀY^V\gVbhꢀ^hꢀXjggZciꢀViꢀi]Zꢀi^bZꢀd[ꢀeg^ci^c\ꢀ
l]Viꢀ^hꢀh]dlcꢀ^cꢀi]ZꢀY^V\gVbꢀbVnꢀaZVYꢀidꢀjcegZ" WjiꢀbVnꢀcdiꢀbViX]ꢀndjgꢀbVX]^cZ#ꢀ>[ꢀndjꢀ[^cYꢀi]^hꢀ
Y^XiVWaZꢀ gZhjaih!ꢀ ^cXajY^c\ꢀ hZg^djhꢀ ^c_jgnꢀ dgꢀ [^gZ#ꢀ idꢀWZꢀi]ZꢀXVhZ!ꢀjhZꢀi]Zꢀl^g^c\ꢀY^V\gVbꢀ^ch^YZꢀi]Zꢀ
I]^hꢀ^cXajYZhꢀi]Zꢀ^chiVaaVi^dcꢀd[ꢀjcVeegdkZYꢀV[iZg" bdidgꢀ_jcXi^dcꢀWdm#
bVg`ZiꢀeVgih#
CAPACITORS/INVERTERS.ꢀ HdbZꢀ XVeVX^idghꢀ
WIRE CONNECTIONS.ꢀ 6aaꢀ XdccZXi^dchꢀ bjhiꢀ VcYꢀedlZgꢀ^ckZgiZghꢀhidgZꢀVcꢀZaZXig^XVaꢀX]Vg\Zꢀ[dgꢀ
WZꢀ i^\]iꢀ idꢀ egZkZciꢀ l^gZhꢀ [gdbꢀ addhZc^c\ꢀ Yjg^c\ꢀ jeꢀ idꢀ &%ꢀ b^cjiZhꢀ V[iZgꢀ WZ^c\ꢀ Y^hXdccZXiZYꢀ [gdbꢀ
bVX]^cZꢀ deZgVi^dc#ꢀ 9djWaZ"X]ZX`ꢀ Vaaꢀ l^gZhꢀ Y^h" i]Zꢀ edlZgꢀ hdjgXZ#ꢀ Idꢀ gZYjXZꢀ i]Zꢀ g^h`ꢀ d[ꢀ WZ^c\ꢀ
XdccZXiZYꢀdgꢀXdccZXiZYꢀYjg^c\ꢀVcnꢀl^g^c\ꢀiVh`ꢀidꢀ h]dX`ZY!ꢀlV^iꢀViꢀaZVhiꢀi]^hꢀadc\ꢀWZ[dgZꢀldg`^c\ꢀdcꢀ
ZchjgZꢀi^\]iꢀXdccZXi^dch#
XVeVX^idgh#
CIRCUIT REQUIREMENTS. Ndjꢀ BJHIꢀ [daadlꢀ EXPERIENCING DIFFICULTIES. >[ꢀndjꢀVgZꢀZmeZ"
i]Zꢀ gZfj^gZbZcihꢀ Viꢀ i]Zꢀ WZ\^cc^c\ꢀ d[ꢀ i]^hꢀ bVc" g^ZcX^c\ꢀY^[[^Xjai^ZhꢀjcYZghiVcY^c\ꢀi]Zꢀ^c[dgbVi^dcꢀ
jVa l]Zcꢀ XdccZXi^c\ꢀ ndjgꢀ bVX]^cZꢀ idꢀ Vꢀ edlZgꢀ ^cXajYZYꢀ ^cꢀ i]^hꢀ hZXi^dc!ꢀ XdciVXiꢀ djgꢀ IZX]c^XVaꢀ
hdjgXZ#
HjeedgiꢀViꢀꢂ*,%ꢃꢀ*)+".++(#
The photos and diagrams
included in this section are
best viewed in color. You
can view these pages in
READ ELECTRICAL SAFETY
ON PAGE 17!
-17-
Model g0513X2B (Mfg. since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
g0513X2b electrical components
figure 19. Magnetic switch.
figure 17. Control panel wiring.
figure 18. Motor wiring.
READ ELECTRICAL SAFETY
-18-
Model g0513X2B (Mfg. since 5/11)
ON DPoAwGnloEad1fr7om! Www.Somanuals.com. All Manuals Search And Download.
g0513X2b Wiring diagram 220v, 1-ph
<gdjcY
EDL:Gꢀ
G
HJEEANꢀ
?JC8I>DC
7DM
=di
A'
=di A&
:
G
H
220 VAC
6-15 PLUG
(as recommended)
<gdjcY
6
G
8DCIGDAꢀE6C:A
H
ꢁk^ZlZYꢀ[gdbꢀWZ]^cYꢂ
see figure 17
A&$&
A'$(
CD&(
A($*
H9:
B6"&-
C8&*
H9:
C8&+
''
&)
'&
E
&(
J
CD&)
I&$'
I'$)
I($+
''
&)
'&
&(
H9:
G6"'%
-"&'
&$'
($)
*$+
-
&'
.+
&%
.-
J
K
.*
''
&)
'&
&(
B6<C:I>8
HL>I8=
see figure 19
<gdjcY
J
K
''%KꢀBDIDG
see figure 18
BV\cZi^Xꢀ7gV`Z
NO<
Gjc
8VeVX^idg
)*B;9
)*%K68
-19-
Model g0513X2B (Mfg. since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
main breakdown
-20-
Model g0513X2B (Mfg. since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
main parts list
REF
PART #
DESCRIPTION
REF
PART #
DESCRIPTION
2
PSS01M
SET SCREW M6-1 X 10
BUSHING
47
48
49
50
51
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
78
79
80
81
82
82-2
82-3
82-4
PCAP06M
P0513048
PCAP04M
P0513050
P0513X2B051
P0513055
PB10M
CAP SCREW M6-1 X 25
RIVET 3.2 X 10
3
P0513X003
P0513004
4
LIFTING EYE BOLT M10-1.5
MACHINE BODY
CAP SCREW M6-1 X 10
CLEAR WINDOW
5
P0513005
7
P0513X007
PW03M
BUSHING
KEY SWITCH
8
FLAT WASHER 6MM
HEX NUT M6-1
UPPER WHEEL COVER
HEX BOLT M6-1 X 25
FLAT WASHER 6MM
BRUSH
10
PN01M
11
P0513011
POINTER
PW03M
12
P0513012
SHOULDER SCREW M4-.7 X 5
UPPER SHAFT
P0513058
PCAP06M
P0513X060
PLN03M
13
P0513013
CAP SCREW M6-1 X 25
STAR KNOB
14
PRP91M
ROLL PIN 5 X 35
15
P0513015
UPPER WHEEL SHAFT HINGE
UPPER WHEEL SHAFT
UPPER WHEEL ASSEMBLY
BUSHING
LOCK NUT M6-1
16
P0513016
P0513062
P0513063
PN03M
STRAIN RELIEF 16MM
HEIGHT POINTER
HEX NUT M8-1.25
HEX BOLT M8-1.25 X 90
KNOB SCREW M10-1.5 X 20
KNOB SCREW M10-1.5 X 53
THREADED HANDLE 10MM
CAM
17
P0513X2B017
P0513017
17-1
17-2
17-3
17-4
17-5
18
P6204LLU
PR25M
BALL BEARING 6204LLU
INT RETAINING RING 47MM
UPPER WHEEL 17"
PB124M
P0513066
P0513067
P0513068
P0513069
P0513070
P0513071
P0513072
PN09M
P0513X2B017-4
T23071
UPPER TIRE
P0513X2B018
P0513017
LOWER WHEEL ASSEMBLY
BUSHING
18-1
18-2
18-3
18-4
18-5
19
PILLOW BLOCK
P6204LLU
PR25M
BALL BEARING 6204LLU
INT RETAINING RING 47MM
LOWER WHEEL 17"
LOWER TIRE
HANDLE M10-1.5
LEVER ROD
P0513X2B018-4
T23071
HEX NUT M12-1.75
SHAFT
P0513074
PBHS22M
PLW04M
P0513X2B019
P0513X2B019-1
P0513X2B019-2
P0513X2B019-3
P0513X2B019-4
P0513X2B019-5
MAG SWITCH ASSEMBLY MPE-18
MAG SWITCH BACK COVER
CONTACTOR SDE MA-18 220V
RELAY SDE RA-20 8-12
MAG SWITCH FRONT COVER
POWER CORD 14AWG X 3C
BUTTON HD CAP SCR M8-1.25 X 20
LOCK WASHER 8MM
COVER
19-1
19-2
19-3
19-4
19-5
P0513078
PSS09M
SET SCREW M8-1.25 X 20
HEX NUT M8-1.25
LOWER WHEEL SHAFT
MOTOR 2HP W/BRAKE
MOTOR FAN COVER
MOTOR FAN
PN03M
P0513081
P0513X2B082
P0513X2B082-2
P0513X2B082-3
P0513X2B082-4
19-6V2 P0513X2B019-6V2 CONTROL CORD 16AWG X 5C V2.05.11
19-7
19-8
19-9
21
22
23
24
25
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
P0513X2B019-7
PS09M
MOTOR CORD 14AWG X 5C
PHLP HD SCR M5-.8 X 10
RECTIFIER (PU-23-2)
FLAT WASHER 8MM
CAP SCREW M8-1.25 X 16
SAW BLADE 1/2" X 131.5"
LOCK WASHER 8MM
CAP SCREW M8-1.25 X 20
IDLE PULLEY
P0513X2B019-9
PW01M
CAPACITOR COVER
82-5V2 P0513X2B082-5V2 R. CAPACITOR 45M 450VAC V2.05.11
PSB11M
82-6
82-9
82-10
82-11
82-12
82-13
83
P0513X2B082-6
P0513X2B082-9
JUNCTION BOX
P0513023
PLW04M
MAGNETIC BRAKE
P0513X2B082-10 BRAKE SHOE
PCAP14M
P0513X028
PN32
PCAP26M
PLW03M
PK23M
CAP SCREW M6-1 X 12
LOCK WASHER 6MM
KEY 5 X 5 X 25
HEX NUT 1-14
PLW09
LOCK WASHER 1"
PB32M
HEX BOLT M10-1.5 X 25
LOCK WASHER 10MM
MOTOR BRACKET
P0513X2B031
P0513032
PRP02M
SWITCH PLATE
84
PLW06M
P0513085
PBHS22M
P0513087
PFS07M
P0513089
PK15M
COMPRESSION SPRING
ROLL PIN 3 X 16
85
86
BUTTON HD CAP SCR M8-1.25 X 20
PLATE
P0513034
P51201
LOCATE BLOCK
87
THRUST BEARING 51201
TAP SCREW M4 X 10
HANDWHEEL
88
FLANGE SCREW M5-.8 X 10
PILLOW BLOCK
PHTEK15M
P0513037
P0513038
PFS07M
89
90
KEY 5 X 5 X 35
ADJUSTING BOLT
91
PB81M
HEX BOLT M8-1.25 X 20 LH
MOTOR PULLEY
FLANGE SCREW M5-.8 X 10
STOP SWITCH
92
P0513092
PVA42
P0513X2B040
P0513X2B041
P0513X2B042
P0513043
PCAP11M
PWF08M
93
V-BELT A-42 4L420
START SWITCH
94
PCAP04M
P0513095
PWF08M
PCAP02M
PLW04M
CAP SCREW M6-1 X 10
LOWER WHEEL COVER
FENDER WASHER 8MM
CAP SCREW M6-1 X 20
LOCK WASHER 8MM
SWITCH CORD
95
SWITCH CORD
97
CAP SCREW M8-1.25 X 16
FENDER WASHER 8MM
UPPER WHEEL SLIDING BRACKET
111
119
P0513046
-21-
Model g0513X2B (Mfg. since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
main parts list
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
170
171
172
173
FLANGE SCREW M5-.8 X 50
PHLP HD SCR M4-.7 X 10
EXT TOOTH WASHER 5MM
CONNECTING CORD
174
175
176
177
TERMINAL BOX
PFS09M
P0513X2B174
P0513X2B175
PFS07M
WIRE NUT P3
PS38M
FLANGE SCREW M5-.8 X 10
STRAIN RELIEF 5/16"
PTLW02M
P0513X2B173
P0513X2B177
-22-
Model g0513X2B (Mfg. since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
fence-guides breakdown
&*,
&*'"&)
&*,"&,K'
&*,"&+
&*,"&)K'
&*,"&*
&*'".
&*'"-
&*'"&*
&*'"&(
&*'"*K'
&*'")
&*,"&&
&*,"&'
&*,"&%
&*,"&
&*,"&-
&*,"&(
&*,"(K'
&*'
&*,"+
&*'",
&*'"&
&*,",
&*,"-
&*,")
&*,"*
&',
&*'"&&
&'+
&*,"&+
&*,"'
&*'"&%
&*'"+
&*,"&(
&*,".
&*+"(
&*'"'
&*'"&'K'
&*'"(
&+&"&
&*+
&+&
&+'
&+(
&*+"'
&*+")
&('
&'-
&,-
&(&
&*)
&*-
&*(
&*+"&
&+-
&+.
&)*"&&
&)*"&-
&)*"&%
&)*"&.
&+)
&+,
&+%
&+*K'
&*.
&)*"&'
&)*"&(
&)*"&)
&)*"&*
&*-
&)*"&.
&)*"-
&)*",
&),
&)*
&)%
&)*"&
&)*"+
&)&
&)+
&)*".
&)*"&,
&)'
&(+
&)*"&+
&)*"'
&)*")
&(,
&)*"*
&)*"(
&(-
&*&
&*%",
&*%"-
&*%"&%
&*%".
&*&")
&*%"&&
&*%"&
&*%"'
&*%"(
&*%")
&*%"*
&*%"+
&*&"+
&*%
&*&"*
&*&"-
&*&".
&*&",
&*&"&%
-23-
Model g0513X2B (Mfg. since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
fence-guides parts list
REF
126
127
128
131
132
136
137
138
140
141
142
145
PART #
DESCRIPTION
REF
PART #
DESCRIPTION
GUIDE BAR
P0513X2B126
P0513X127
P0513X128
PBHS22M
PLW04M
TABLE 17" X 24"
152-1
152-2
152-3
152-4
P0513X2B152
P0513X2B152-2
PFH04M
TABLE INSERT
GUIDE PIECE
FLAT HD SCR M6-1 X 8
POINTER
TABLE PIN
BUTTON HD CAP SCR M8-1.25 X 20
LOCK WASHER 8MM
CAP SCREW M5-.8 X 10
FLAT WASHER 5MM
PROTECTIVE COVER ASSY
SHOULDER SCREW
FIBER WASHER
P0513X2B152
152-5V2 P0513X2B152-5V2 PHLP HD SCR 10-24 X 3/16
PCAP50M
PW02M
152-6
152-7
152-8
152-9
152-10
152-11
P0513X2B152-6
P0513X2B152
PW01M
SHOULDER SCREW
MITER GAUGE BODY
FLAT WASHER 8MM
HANDLE
P0513X138
P0513X140
P0513X141
P0513X142
P0513X2B145
P0513X2B152
P0513X2B152
P0513X2B152
FIXED BLOCK
SLIDING PLATE
LOCKING SHAFT
GUIDE BRACKET ASSEMBLY
SET SCREW M5-.8 X 5
CAP SCREW M6-1 X 16
PHLP HD SCR M4-.7 X 10
HEX NUT M4-.7
152-12V2 P0513X2B152-5V2 PHLP HD SCR 10-24 X 3/16
145-1 PSS07M
145-2 PCAP01M
145-3 PS38M
152-13
152-14
152-15
153
PN04M
HEX NUT M4-.7
PS56M
PHLP HD SCR M4-.7 X 16
SCALE
P0513X2B152-15
P0513X2B153
P0513X2B154
P0513X2B156
P0513X2B156-1
P0636X122
145-4 PN04M
KNOB SCREW M8-1.25 X 20
OUTER RAIL PLATE
RESAW FENCE ASSEMBLY
RESAW FENCE (AL) L=590
TAP SCREW 3.5 X 8
FENCE PIECE 148 X 22 X 1
RESAW FENCE SCALE
FENCE ASSSMBLY
FENCE
145-5 P0513X144
145-6 P0513X145
145-7 P0513X129
145-8 P0513X130
145-9 PLW04M
145-10 P0513X133
145-11 P0513X134
145-12 P0513X135
145-13 P0513X122
145-14 P0513X123
145-15 P0513X124
145-16 PCAP11M
145-17 PFH31M
145-18 PN05M
RACK
154
UPPER GUIDE TUBE
LOCATE BUSHING
BUSHING
156
156-1
156-2
156-3
156-4
157
LOCK WASHER 8MM
GUIDE BRACKET
WORM CYLINDER
FIXED PLATE
P0513X2B156-3
P0513X2B156-4
P0513X2B157
P0513X2B157-1
P0513X2B157-2
157-1
157-2
GEAR
POINTER
FIXED BOLT
157-3V2 PSS21M
SET SCREW M8-1.25 X 25
SPRING PIECE
COVER
157-4
157-5
157-6
157-7
157-8
157-9
157-10
157-11
157-12
157-13
P0513X2B157-4
CAP SCREW M8-1.25 X 16
FLAT HD SCR M4-.7 X 8
HEX NUT M16-1.5
PFS17M
FLANGE SCREW M4-.7 X 8
PIVOT BLOCK
P0513X2B157-6
PN03M
HEX NUT M8-1.25
HANDLE
145-19 P0513X2B145-19 GUIDE BRACKET SET SCREW
P0513X2B157-8
P0513X2B157-9
P0513X2B157-10
P0513X2B157-11
PSS14M
146
147
150
P0513X146
PCAP02M
P0513X150
HANDWHEEL
SHAFT
CAP SCREW M6-1 X 20
BLADE ADJUSTMENT ASSY
UPPER BLADE GUIDE SUPPORT
BIAS SHAFT
FENCE PLASTIC SET SCREW
NYLON PAD
150-1 P0513X150-5
150-2 P0513X150-6
150-3 PR05M
SET SCREW M8-1.25 X 12
HEX NUT M8-1.25
HEX BOLT M8-1.25 X 20
HEX NUT M8-1.25
FLAT WASHER 8MM
PN03M
EXT RETAINING RING 15MM
BALL BEARING 6202ZZ
HANDLE BUSHING
157-14V2 PB09M
150-4 P6202ZZ
157-15
157-16
PN03M
PW01M
150-5 P0513X150-9
150-6 PCAP48M
150-7 P0513X150-11
150-8 PSS01M
CAP SCREW M6-1 X 35
UPPER SPACING SLEEVE
SET SCREW M6-1 X 10
CAP SCREW M6-1 X 16
UPPER GUIDE SUPPORT BLOCK
157-17V2 P0513X2B157-17V2 LOCK HANDLE M8-1.25 X 45 V2.05.11
157-18
158
P0513X2B157-18
PW01M
MOVING PLATE
FLAT WASHER 8MM
LOCK WASHER 8MM
CAP SCREW M8-1.25 X 20
GUARD RAIL
150-9 PCAP01M
150-10 P0513X150-2
159
PLW04M
160
PCAP14M
P0513X2B161
P0513X2B161-1
P0513X2B162
PW03M
150-11 P0513X2B150-11 ADJUST BAR
161
151
P0513X151
BLADE ADJUSTMENT ASSY
LOWER BLADE GUIDE SUPPORT
CAP SCREW M6-1 X 16
BIAS SHAFT
161-1
162
FENCE SCALE
151-4 P0513X151-5
151-5 PCAP01M
151-6 P0513X151-7
151-7 PR05M
INNER RAIL PLATE
FLAT WASHER 6MM
LOCK WASHER 6MM
CAP SCREW M6-1 X 20
HEX WRENCH 5MM
HEX WRENCH 8MM
WRENCH 10 X 13
163
164
PLW03M
EXT RETAINING RING 15MM
BALL BEARING 6202ZZ
HANDLE BUSHING
165V2
167
PCAP02M
PAW05M
151-8 P6202ZZ
151-9 P0513X151-10
151-10 PCAP48M
168
PAW08M
CAP SCREW M6-1 X 35
MITER GAUGE ASSY
169
PWR1013
PW01M
152
P0513X152
178
FLAT WASHER 8MM
-24-
Model g0513X2B (Mfg. since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
trunnion breakdown
&**"-
&**",
&**".
&**"&
&**"&
&**"&+
&**"'
&**
&**"&%
&**"&&
&**"(&
&**"(
&**")
&**"*
&**"+
&**"&(
&**"&
&**"&'
&**"&)
&**"&*
&**"(
&**"'(
&**"&,
&**"&-
&**"&.
&**"')
&**"&
&(.K'
&**"((
&**"(%
&**"'.
&**"'%K'
&**"'
&%(
&%)
&**"('
&**"'&
&**"'-
&**"',
&**"''
&**"'+
&**"'*
&%(
&%)
.-
REF PART #
DESCRIPTION
REF
PART #
DESCRIPTION
98
PCAP84M
PLW06M
PW04M
CAP SCREW M10-1.5 X 35
LOCK WASHER 10MM
FLAT WASHER 10MM
CAP SCREW M10-1.5 X 35
CAST IRON TRUNNION ASSEMBLY
FLAT WASHER 8MM
155-15
155-16
155-17
155-18
155-19
P0513120
PLW04M
P0513109
PN01M
POINTER
103
104
LOCK WASHER 8MM
ADJUST BOLT M6-1
HEX NUT M6-1
139V2 PCAP84M
155 P0513X2155
P0513X2174
ADJUST PLATE
155-1 PW01M
155-2 PLN04M
155-3 PS17M
155-20V2 PFH30M
FLAT HD SCR M5-.8 X 8
CAP SCREW M6-1 X 16
CAP SCREW M6-1 X 50
LOCK NUT M8-1.25
155-21
155-22
155-23
155-24
155-25
155-26
155-27
155-28
155-29
155-30
155-31
155-32
155-33
PSB01M
PHLP HD SCR M4-.7 x 6
GEAR PLATE
PSB37M
155-4 P0513115
155-5 PFH27M
155-6 PCB10M
155-7 P0513X2162
155-8 PCB23M
155-9 P0513118
155-10 P0513X2165
155-11 PW01M
155-12 PB07M
P0513X2178
P0513100
PBHS19M
P0513X2181
P6000
TRUNNION SUPPORT BRACKET
SMALL GEAR
FLAT HD SCR M4-.7 X 6
CARRIAGE BOLT M8-1.25 X 85
UPPER TRUNNION
BUTTON HD CAP SCR M10-1.5 X 30
RIGHT COVER
CARRIAGE BOLT M8-1.25 X 80
LOCK HANDLE M8-1.25
ANGLE LABEL
BALL BEARING 6000ZZ
FLAT WASHER 10MM
LEFT COVER
PW04M
P0513X2184
P0513X2185
PW01M
FLAT WASHER 8MM
ADJUST BLOCK
HEX BOLT M8-1.25 X 25
LOCK HANDLE M8-1.25
FLAT WASHER 4MM
FLAT WASHER 8MM
CAP SCREW M5-.8 X 6
LOCK WASHER 10MM
155-13 P0513X101
155-14 PW05M
PCAP97M
PLW06M
-25-
Model g0513X2B (Mfg. since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
labels breakdown
'&)
'%'
'%&
'%(
'%)
'&*
'&+K'
'%*
'%+
'%-
'%,
'%.
'&%
'&&
'&'
'&(
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
201
202
203
204
205
206
207
208
P0513X2B201
G0513X2B MODEL # LABEL
GRIZZLY LOGO PLATE
OPEN DOOR LABEL
209
210
211
212
213
214
215
PLABEL-14
P0513X210
PLABEL-18
PLABEL-20
PPAINT-11
P0513X214
PPAINT-1
ELECTRICITY LABEL
EXTREME SERIES PLATE
DISCONNECT POWER LABEL
OPEN DOOR LABEL
G8588
PLABEL-20
P0513X204
P0513X205
PLABEL-11
PLABEL-19
PLABEL-12
GUARD ADJ LABEL
SCALE DIRECTIONS LABEL
SAFETY GLASSES LABEL
HANDS/BLADE LABEL
READ MANUAL LABEL
"PUTTY" PAINT
TENSION ADJ LABEL
"GRIZZLY GREEN" PAINT
216V2 P0513X2B216V2 MACHINE ID LABEL CSA V2.05.11
safety labels warn about machine hazards and ways to prevent injury. the owner of this machine
must maintain the original location and readability of the labels on the machine. if any label is
removed or becomes unreadable, replace that label before using the machine again. contact
grizzly at (800) 523-4777 or www.grizzly.com to order new labels.
-26-
Model g0513X2B (Mfg. since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
accessories
t20501—face shield crown protector 4"
t20502—face shield crown protector 7"
t20503—face shield Window
some aftermarket accessories can be
installed on this machine that could cause
it to function improperly, increasing the risk
of serious personal injury. to minimize this
risk, only install accessories recommended
for this machine by grizzly.
t20452—"Kirova" anti-reflective s. glasses
t20451—"Kirova" clear safety glasses
h0736—shop fox® safety glasses
h7194—bifocal safety glasses 1.5
h7195—bifocal safety glasses 2.0
h7196—bifocal safety glasses 2.5
NOTICE
refer to the newest copy of the grizzly
catalog for other accessories available for
this machine.
t20502
t20452
t20503
t20451
h0736
replacement blades
these replacement blades are milled for exact
tooth set and are made with high quality tool
steel.
h7194
1311⁄2" carbon steel replacement blades for
the model g0513X2b
figure 20. eye protection assortment.
g5562—slipit® 1 Qt. gel
model
h4803
h4804
h4805
h4806
h4807
h4808
h4809
h4810
h4811
Width
tpi
g5563—slipit® 12 oz spray
1
⁄8
⁄4
⁄4
⁄8
⁄2
⁄2
⁄4
"
"
"
"
"
"
"
14 rAKer
6 hooK
18 rAKer
10 rAKer
6 hooK
10 rAKer
3 hooK
6 hooK
2 hooK
g2871—boeshield® t-9 12 oz spray
g2870—boeshield® t-9 4 oz spray
h3788—g96® gun treatment 12 oz spray
h3789—g96® gun treatment 4.5 oz spray
1
1
3
1
1
3
1"
1"
figure 21. recommended products for protect-
ing unpainted cast iron/steel part on machinery.
-27-
Model g0513X2B (Mfg. since 5/11)
Download from Www.Somanuals.com. All Manuals Search And Download.
Buy Direct and Save with Grizzly® – Trusted, Proven and a Great Value!
~Since 1983~
Visit Our Website Today For
Current Specials!
ORDER
24 HOURS A DAY!
1-800-523-4777
Download from Www.Somanuals.com. All Manuals Search And Download.
|