Promaster 310
Owner/Operator Manual
Models
990018
25 HP Kohler
990020
23 HP Kawasaki
ENGLISH
FRANÇAIS
ESPAÑOL
08495100A 1/02
Supercedes 08495100
Printed in USA
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Attachments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
INTRODUCTION
affect the performance, durability, or safety of this unit.
Gravely disclaims liability for any claims or damages,
whether warranty, property damage, personal injury or
death arising out of the use of unauthorized replacement
parts.
THE MANUAL
Before operation of unit, carefully and completely read
your manuals. The contents will provide you with an
understanding of safety instructions and controls during
normal operation and maintenance.
DISCLAIMER
All reference to left, right, front, or rear are given from
operator sitting in operation position and facing the
direction of forward travel.
Gravely reserves the right to discontinue, make changes
to, and add improvements upon its products at any time
without public notice or obligation. The descriptions and
specifications contained in this manual were in effect at
printing. Equipment described within this manual may be
optional. Some illustrations may not be applicable to your
unit.
MODEL AND SERIAL NUMBERS
When ordering replacement parts or
Transfer
model & serial
number label
from product
registration
here.
making service inquiries, know the
Model and Serial numbers of your unit
and engine.
DELIVERY
Customer Note: If you have purchased this product
without complete assembly and instruction by your
retailer, it is your responsibility to:
Numbers are located on the product
registration form in the unit literature
package. They are printed on a serial
number label, located on the frame of
your unit.
1. Read and understand all assembly instructions in
this manual. If you do not understand or have
difficulty following the instructions, contact your
nearest Gravely Dealer for assistance. Make sure
all assembly has been properly completed and
safety interlock system works properly.
Serial
Number
Label
NOTE: To locate your nearest Gravely Dealer, call
internet.
WARNING: Improper assembly or adjustments
can cause serious injury.
OF3380
Figure 2
2. Understand all Safety Precautions provided in the
manuals.
•
•
Record Unit Model and Serial numbers here.
3. Review control functions and operation of the unit.
Do not operate unit unless all controls function as
described in this manual.
Record Engine Model and Serial numbers here.
4. Review recommended lubrication, maintenance
and adjustments.
5. Fill out Original Purchaser Registration Card and
return the card to Gravely Company.
UNAUTHORIZED REPLACEMENT PARTS
Use only Gravely replacement parts. The replacement of
any part on this vehicle with anything other than an
Gravely authorized replacement part may adversely
© Copyright 2002 Ariens Company
GB - 3
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
SAFETY ALERTS
NOTATIONS
Look for these symbols to point out
NOTE: General reference information for proper
important safety precautions. They mean:
operation and maintenance practices.
IMPORTANT: Specific procedures or information
required to prevent damage to unit or attachment.
Attention!
Personal Safety Is Involved!
Become Alert!
PRACTICES AND LAWS
Practice usual and customary safe working precautions,
for the benefit of yourself and others. Understand and
follow all safety messages. Be alert to unsafe conditions
and the possibility of minor, moderate, or serious injury or
death. Learn applicable rules and laws in your area.
Always follow the practices set forth in this manual.
Obey The Message!
The safety alert symbols above and signal words below
are used on decals and in this manual.
Read and understand all safety messages.
DANGER: IMMINENTLY HAZARDOUS
SITUATION! If not avoided, WILL RESULT in
death or serious injury.
REQUIRED OPERATOR TRAINING
Original purchaser of this unit was instructed by the seller
on safe and proper operation by the seller. If unit is to be
used by someone other than original purchaser; loaned,
rented or sold, ALWAYS provide this manual and any
needed safety training before operation.
WARNING: POTENTIALLY HAZARDOUS
SITUATION! If not avoided, COULD RESULT in
death or serious injury.
SAFETY DECALS AND LOCATIONS
ALWAYS replace missing or damaged Safety Decals.
Refer to figure below for Safety Decal locations.
CAUTION: POTENTIALLY HAZARDOUS
SITUATION! If not avoided, MAY RESULT in
minor or moderate injury. It may also be used to
alert against unsafe practices.
GB - 4
Download from Www.Somanuals.com. All Manuals Search And Download.
1 & 2. DANGER
Read the operator’s manual.
ASSEMBLY SAFETY RULES
Read, understand, and follow all safety practices in
Owner/Operator Manual before beginning assembly.
Failure to follow instructions could result in personal
injury and/or damage to unit.
OL1801
ALWAYS remove key and/or wire from spark plug before
assembly. Unintentional engine start up can cause death
or serious injury.
Keep children and others away from unit while
operating.
OL4140
OPERATIONAL SAFETY RULES
Walk Around Inspection
Never direct discharge toward other people.
Thrown objects can cause injury.
Complete a walk around inspection of unit and work area
to understand:
OL0910
• Work area • Your unit • All safety decals
Look down and behind before and while
backing.
Work Area
ALWAYS check overhead and side clearances carefully
before operation. ALWAYS be aware of traffic when
operating along streets or curbs.
Keep children and people away. Keep children out of
work area and under watchful care of a responsible adult.
OL4780
OL4790
Keep children out of work area and under
watchful care of a responsible adult.
Keep area of operation clear of all toys, pets, and debris.
Thrown objects can cause injury.
Never carry children.
Check for weak spots on dock, ramps or floors. Avoid
uneven work areas and rough terrain. Stay alert for
hidden hazards.
OL4800
Avoid uneven and rough terrain. DO NOT operate near
drop offs, ditches, or embankments. Unit can suddenly
turn over if a wheel is over the edge of a cliff or ditch, or if
an edge caves in.
Go up and down slopes, not across.
MAX
10°
10°
OL4770
Personal Safety
Disengage PTO before tilting deck upward.
Data indicates that operators, age 60 and above, are
involved in a larger percentage of riding mower related
injuries. These operators should evaluate their ability to
operate the riding mower safely enough to protect
themselves and others from serious injury.
OL4820
•Never allow operation by untrained
persons.
Only trained adults may operate unit.
Training includes actual operation.
•
If machine stops going uphill, stop blade and back
down slowly.
NEVER allow children to operate or play on or near unit.
Be alert and shut off unit if children enter area.
NEVER operate unit after or during the use of
medication, drugs or alcohol. Safe operation requires
your complete and unimpaired attention at all times.
DO NOT wear loose clothing or jewelry and tie back hair
that may get caught in rotating parts.
Wear adequate outer garments.
•
•
Avoid sudden turns.
Keep safety devices (guards, shields, switches,
etc.) in place and working.
•
•
Check interlock system per manual before use.
Understand location and function of all controls.
3. HOT SURFACES!
DO NOT touch parts which are hot from
operation. ALWAYS allow parts to cool.
NEVER wear open sandals or canvas shoes during
operation. Wear adequate safety gear, protective gloves
and footwear.
OD0061
Wear proper footwear to improve footing on slippery
surfaces.
Always wear safety goggles or safety glasses with side
shields when operating mower.
4. DANGER!
PINCH POINT
Moving parts can cut or amputate fingers or a hand.
Wrap blade(s) or wear gloves to service.
OL4830
IMPORTANT: On multi-blade mowers, rotation of one
blade will cause all blades to rotate.
GB - 5
Download from Www.Somanuals.com. All Manuals Search And Download.
NEVER place your hands or any part of your body or
clothing inside or near any moving part while unit is
running.
If equipment vibrates abnormally, stop engine at once,
wait for moving parts to stop and remove wire from spark
plug. Repair any damage before restarting unit.
Take all possible precautions when leaving unit
unattended. Shut off engine. Remove wire from spark
plug and secure it away from spark plug.
ALWAYS keep hands and feet away from all rotating
parts during operation. Rotating parts can cut off body
parts.
ALWAYS keep body and hands away from pin holes or
ALWAYS remove key to prevent unauthorized use.
nozzles which eject hydraulic fluid under pressure.
Know the weight of loads. Limit loads to those you can
safely control and the unit can safely handle.
Disengage PTO when attachment is not in use. ALWAYS
turn off power to attachment when travelling, crossing
driveways, etc.
DO NOT touch parts which are hot. Allow parts to cool.
ALWAYS keep hands and feet away from all pinch points.
Fumes from the engine exhaust can cause death or
serious injury. DO NOT run engine in an enclosed area.
Always provide good ventilation.
Operation
Understand:
•
•
•
•
•
How to operate all controls
The functions of all controls
How to STOP in an Emergency
Braking and steering characteristics
Turning radius and clearances
Keep safety devices or guards in place and functioning
properly. NEVER modify or remove safety devices.
Ensure Safety Interlock System is functioning properly.
DO NOT operate unit if safety interlock is damaged or
disabled.
Before starting engine: disengage PTO, place direction
control pedal in neutral, lower attachment and set parking
brake.
Dust, smoke, fog, etc. can reduce vision and cause an
accident. Mow only in daylight or good artificial light.
Avoid slippery surfaces. Always be sure of your footing.
DO NOT mow on wet grass. Reduced traction could
cause sliding.
Watch for traffic when operating near or crossing
roadways.
Never carry passengers.
DO NOT try to stabilize the machine by putting your foot
on the ground.
Never direct discharge towards persons or property that
may be injured or damaged by thrown objects. Use
extreme caution on gravel surfaces. Stay alert for hidden
hazards or traffic.
Always stand clear of the discharge area.
ALWAYS disengage PTO, stop unit and engine, remove
key, engage parking brake and allow moving parts to stop
before leaving operator’s position.
Never engage PTO while raising attachment or when
attachment is in raised position.
DO NOT operate at too fast a rate. DO NOT change
engine governor settings or over-speed engine. Slow
down before turning.
DO NOT operate in reverse unless absolutely necessary.
ALWAYS look down and behind before and while
backing.
GB - 6
Replace fuel cap securely and clean up spilled fuel.
MAINTENANCE AND SERVICE SAFETY
RULES
ALWAYS block wheels and know all jack stands are
strong and secure and will hold weight of unit during
maintenance.
Never fill containers inside a vehicle or on a truck or
trailer bed with a plastic liner. Always place containers on
the ground away from your vehicle before filling.
When practical, remove gas-powered equipment from
the truck or trailer and refuel it on the ground. If this is not
possible, then refuel such equipment on a trailer with a
portable container, rather than from a gasoline dispenser
nozzle.
Keep nuts and bolts tight, especially blade attachment
bolts, and keep equipment in good condition.
NEVER attempt to make any adjustments to unit while
engine is running. Stop engine, remove spark plug wire
and wait for all moving parts to stop before servicing
(except where specifically recommended).
Keep the nozzle in contact with the rim of the fuel tank or
container opening at all times until fueling is complete.
Do not use a nozzle lock-open device.
Check parking brake operation frequently. Adjust and
service as required.
If fuel is spilled on clothing, change clothing immediately.
ALWAYS maintain unit in safe operating condition.
Damaged or worn out muffler can cause fire or explosion.
NO smoking, NO sparks, NO flames. ALWAYS allow
engine to cool before servicing.
BATTERY
Avoid Electric Shock. Objects contacting both battery
terminals at the same time may result in injury and unit
damage. DO NOT reverse battery connections.
Maintain or replace safety and instructions labels, as
necessary.
Explosive Gases from battery can cause death or serious
injury. Poisonous battery fluid contains sulfuric acid and
its contact with skin, eyes or clothing can cause severe
chemical burns.
STORAGE SAFETY RULES
NEVER store unit with fuel in fuel tank, inside a building
where any ignition sources are present.
Allow engine to cool completely before storing in closed
area or covering unit.
No flames, No sparks, No smoking near battery.
ALWAYS wear safety glasses and protective gear near
battery.
DO NOT TIP battery beyond a 45˚ angle in any direction.
For extended storage, clean unit thoroughly. See engine
manual for proper storage.
ALWAYS keep batteries out of reach of children.
Lower cutting deck unless a positive mechanical lock is
used.
Battery posts, terminals and related accessories contain
lead and lead compounds, chemicals known to the State
of California to cause cancer and reproductive harm.
Wash hands after handling.
ACCESSORY AND ATTACHMENT SAFETY
RULES
Use only attachments or accessories designed for your
unit.
Battery Electrolyte First Aid
Follow First Aid directions for contact with battery fluid.
•
•
External Contact: Flush with water.
Check attachment components frequently. If worn or
damaged, replace with manufacturer’s recommended
parts.
Eyes: Flush with water for at least 15 minutes and
get medical attention immediately!
•
Internal Contact: Drink large quantities of water.
Follow with Milk of Magnesia, beaten egg or
vegetable oil. Get medical attention immediately!
In case of internal contact, DO NOT induce vomiting!
GB - 7
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Fill Engine Crankcase
WARNING: AVOID INJURY. Read and
understand Assembly, Fuel and Battery Safety
Rules before proceeding.
The unit is shipped without oil in engine crankcase. Refer
to engine manual for proper oil type and crankcase
capacity.
Check Hydraulic Oil
See Maintenance.
Tools required:
•
socket wrench, 15/16"
Fill Engine Fuel Tank
•
tire gauge
Unpack Unit
Remove unit and all other components from the shipping
container.
Charge Battery
See instructions for battery removal and charging in
Install Handlebar
Install Deck
1. Remove nut securing handlebar to shaft.
See deck Owner/Operator Manual.
2. Remove handlebar from shaft.
Check Safety Interlock System
See Maintenance.
3. Place handlebar on shaft so handle grips are up
and angled toward front of unit.
4. Replace nut securing handlebar to shaft.
WARNING: Failure of safety interlock and
improper operation could result in death or
serious injury.
Prepare Seat
Remove and discard hair pin and clevis pin from back of
seat.
Check Function of All Controls
Ensure unit runs and performs properly. Refer to
Operation.
Check Tire Pressure
Check tire pressure and adjust. Adjust front tires to 12-15
PSI (82.8 - 103.4 kPa). Adjust rear tires to 20-25 PSI
(137.9 - 172.4 kPa).
WARNING: Failure of controls could result in
death or serious injury.
OPERATION
Parking Brake Interlock System
WARNING: AVOID INJURY. Read and
understand Operational, Fuel and Battery
Safety Rules before proceeding.
Moving direction control pedal with parking brake
engaged will shut off engine.
Ignition Switch
The ignition switch is operated by a
removable key.
1
CONTROLS AND FEATURES
See Figure on page 2 for all Controls and Features
locations.
2
To start:
3
1. Insert the key.
Safety Interlock System
PTO must not engage unless operator is sitting in seat.
2. Turn the switch clockwise from the OFF
(1) position to the START (3) position.
The key will spring back to the RUN (2) position.
OF1210
Engine must not start unless PTO is disengaged and
direction control pedal is in neutral position.
To stop the engine, turn key to the OFF (1) position.
CAUTION: Safety interlock system failure and
improper operation of unit can result in death or
serious injury. Test this system each time the
unit is operated. If this system does not function
as described, do not operate until repairs are
made.
GB - 8
Download from Www.Somanuals.com. All Manuals Search And Download.
Throttle Lever
Oil Pressure Warning Light
Move lever to FAST (1) position to increase
engine speed. Move lever to SLOW (2)
position to decrease engine speed.
If light turns on during operation:
1
1. Stop unit and engine.
2. Wait five minutes.
2
3. Check engine oil level and fill if
OG0601
necessary.
OE0340
4. Check for external damage to engine.
Choke
To test oil pressure warning light, turn ignition key to the
run position. Light should turn on.
Pull choke control out to start a cold engine.
Push control in as engine warms up.
Parking Brake Lever
OE0590
Pull lever backward to engaged (2)
position to activate parking brake.
Handlebar
Push lever forward in disengaged (1)
position to deactivate parking brake.
1
2
Turn handlebar clockwise to steer right. Turn handlebar
counterclockwise to steer left.
NOTE: Unit spins in a zero turn radius when handlebar is
turned to maximum position in either direction.
OF1332
PTO Switch
Speed and Direction Control Pedal
The power take-off switch is used to engage
and disengage the attachment.
Press pedal forward (1) to move tractor
forward.
1
1
2
Lift switch to engage (1) attachment.
Press pedal backward (2) to move the
tractor backward.
Push switch down to disengage (2)
attachment.
Remove foot from pedal to return unit
to neutral.
OE0261
2
Hourmeter
OF3390
Records total time key is in RUN position.
Deck Lift Lever
Seat Adjustment Lever
Pull lever out and slide seat to desired position. Release
lever to lock seat in position.
Pull lever backwards to LIFT (3)
position to lift mower.
1
Place lever in HOLD (2) position
to hold mower in current position.
Seat Suspension Adjustment Knob
To make seat more firm turn knob clockwise. To make
seat less firm turn knob counterclockwise.
Push lever forward to FLOAT (1)
position for mowing.
2
3
Transmission Bypass Valve
IMPORTANT: Disengage PTO
before pulling lever back to LIFT.
The transmission bypass valve disengages the
transmission to allow manual movement of unit. See
Cut Height Lever
To raise attachment, move lever
OF3310
backward.
FILLING FUEL TANK
To lower attachment, move lever
forward.
WARNING: AVOID INJURY. Read and
understand Fuel Safety Rules before
proceeding.
To hold attachment in place, release
lever.
To add fuel to fuel tank:
1. Place unit in an open or well-ventilated area.
2. Stop engine and allow to cool.
OL4810
3. Clean fuel cap and surrounding area to prevent dirt
from entering fuel tank.
4. Remove fuel cap.
IMPORTANT: See engine manual for correct type and
grade of fuel.
GB - 9
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Fill fuel tank to within 1/2" (1.3 cm) below bottom of
MOVING UNIT MANUALLY
IMPORTANT: Never tow unit.
1. Stop engine.
filler neck.
NOTE: Fuel tank capacity is 7.5 gal. (28.4L).
6. Replace fuel cap and tighten.
7. Clean up any spilled fuel.
2. Turn transmission bypass valve counterclockwise
1/4 turn.
3. Disengage parking brake.
TO STOP IN AN EMERGENCY
Turn ignition key to OFF.
4. Push unit to desired location.
5. Engage parking brake.
STARTING THE ENGINE
6. Turn transmission bypass valve clockwise 1/4 turn.
1. Check each item in Before Each Use in the
Maintenance Schedule.
To allow
manual
movement:
2. Disengage PTO.
3. Engage parking brake.
4. Apply choke to a cold engine.
5. Place throttle lever to FAST when starting a warm
engine. Place throttle lever in a middle position
when starting a cold engine.
To engage
transmission:
6. Turn key to START position.
IMPORTANT: DO NOT operate starter motor more than
15 seconds per minute, as overheating and damage can
occur. If engine will not start, refer to Troubleshooting or
Engine Manual.
7. When engine starts, release to RUN position.
8. Disengage parking brake.
Figure 4
OF3370
OPERATING UNIT
To mow:
1. Take foot off direction control pedal to place unit in
neutral.
2. Place throttle lever in middle position.
3. Engage PTO.
4. Set throttle to FAST.
5. Depress direction control pedal for desired mowing
speed.
6. Disengage PTO when finished mowing.
STOPPING
1. Take foot off direction control pedal to place unit in
neutral.
2. Move throttle lever to SLOW.
3. Turn ignition key to OFF.
PARKING
1. Stop as instructed above.
2. Engage parking brake.
3. Remove ignition key.
GB - 10
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Gravely Dealers will provide any service or adjustments
CHECKING SAFETY INTERLOCK SYSTEM
Test the safety interlock system before each use. If the
system does not function properly, do not operate the unit
until repairs are made.
which may be required to keep your unit operating at
peak efficiency. Should engine service be required,
contact an Gravely dealer or an authorized engine
manufacturer's service center.
CAUTION: Safety interlock system failure and
improper operation of unit can result in death or
serious injury. Test this system each time the
unit is operated. If this system does not function
as described, do not operate until repairs are
made.
WARNING: AVOID INJURY. Read and
understand Maintenance and Service and
Battery Safety Rules in Safety section before
attempting any maintenance.
The PTO must not engage unless operator is sitting on
seat. To test:
MAINTENANCE SCHEDULE
Intervals
Service Performed
1. Start engine.
Before each use:
Check Safety Interlock System
Check Fasteners
2. Stand up off of seat.
3. Lift PTO switch. PTO must not engage.
Check Parking Brake Interlock
Check Parking Brake
Check Tires
Engine must not start unless PTO is disengaged and the
speed control pedal is in neutral. To test:
1. With engine off, engage PTO.
Check Hydraulic Oil Level
Clean Unit
2. Turn ignition switch to Start. Engine must not crank.
3. Disengage PTO.
Check Engine Oil Level
4. Press speed control pedal forward.
5. Turn ignition switch to Start. Engine must not crank.
1
Check Air Cleaner
1
Check Air Intake
Every 25 hours:
Check and Clean Battery
Clean Hydraulic Pump
Lubricate Unit
CHECK FASTENERS
Be certain that all hardware is tightened to the proper
torque. Pay special attention to mower blades, guards
and safety shields.
1
Service Precleaner
1
Check Engine Oil Cooler
CHECK PARKING BRAKE INTERLOCK
Ensure unit shuts off when direction control pedal is
depressed with the parking brake engaged.
Clean Hydraulic Oil Cooler
After first 50 hours: Replace Hydraulic Oil Filter
Every 50 hours:
Every 100 hours:
Inspect Spark Arrestor
Check Fasteners
Check Belts
CHECK PARKING BRAKE
With parking brake engaged, push unit. If unit rolls, adjust
parking brake. See Service and Adjustments.
1
Replace Air Cleaner
CHECK TIRES
Change Oil
1
Adjust front tires to 12 - 15 PSI (82.8 - 103.4 kPa). Adjust
rear tires to 20 - 25 PSI (137.9 - 172.4 kPa).
Clean Cooling Areas
Every 200 hours:
Replace Hydraulic Oil Filter
Change Engine Oil Filter
Check Spark Plugs
Check Belts
CHECK AND CLEAN BATTERY
WARNING: AVOID INJURY. Read and
understand Battery Safety Rules in Safety
section before proceeding.
Every season:
Before storage:
Check Fasteners
Check and Clean Battery
Clean Hydraulic Pump
Lubricate Unit
Clean Battery
Keep battery and its terminals clean. Inspect every 25
operating hours or monthly for best performance.
Clean Unit
1
Change more often in dirty, dusty conditions.
1. Remove battery cover.
GB - 11
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Disconnect cables from battery (negative, then
positive).
REPLACING HYDRAULIC OIL FILTER
Replace hydraulic oil filter after the first 50 hours of
operation and every 200 hours thereafter.
3. Clean terminals and battery cable ends with wire
brush.
1. Clean around dipstick cap and dipstick. Remove
dipstick.
4. Coat terminals with grease or petroleum jelly.
5. Reconnect cables to battery (positive, then
negative).
2. Place container under oil filter to catch dripping oil.
3. Remove oil filter.
6. Replace battery cover.
4. Install new oil filter.
5. Check hydraulic oil level and add if necessary.
6. Clean up any oil spills.
Electrolyte Level
Every 25 hours of operation or each week check
electrolyte level of each cell by removing caps one at a
time. The electrolyte level should be at level indicator.
Use distilled water to fill each cell if needed.
IMPORTANT: See Service and Adjustments for changing
hydraulic oil.
CHECK BELTS
CLEAN HYDRAULIC PUMP
Check belts every 100 hours and every season. Replace
worn or deteriorated belts. Replace belts to
accommodate belt stretch and wear in the traction drive
or mower drive. Refer to Service and Adjustments for
procedures.
Clean hydraulic pump before each use and before
storage. Keep pump surface free from buildup of dirt and
debris.
LUBRICATE UNIT
Every 25 hours and before storage:
CLEAN UNIT
Clean unit before each use and before storage.
•
Grease steering caster spindle and handlebars.
•
Clean engine, battery, seat, deck, etc. of all dirt and
debris with a brush or cloth. Do not use solvents,
harsh cleaners or abrasives.
•
•
Keep finished surfaces and wheels free of all
gasoline, oil, etc.
Protect painted surfaces with automotive type wax.
Lightly coat unpainted surfaces with spray lubricant
and wipe off excess with soft cloth.
CHECK ENGINE OIL LEVEL
Check engine oil level before each use.
1. Remove oil fill cap/dipstick.
2. Check level on oil dipstick.
3. Add more oil if needed.
4. Tighten fill cap securely.
CHECK HYDRAULIC OIL LEVEL
Check hydraulic oil level before each use.
See engine manual for detailed instructions.
IMPORTANT: Maintain proper oil level to prevent engine
damage.
IMPORTANT: Hydraulic tank MUST be filled before
starting engine.
CHECK AIR CLEANER
1. Stop engine.
Check air cleaner before each use. See engine manual
for detailed instructions.
2. Place deck lift lever in FLOAT position.
3. Remove any dirt that may be around the cap on the
tank.
CHECK AIR INTAKE
Check air intake before each use. See engine manual for
detailed instructions.
4. Remove cap and dipstick.
5. Check hydraulic oil level mark on dipstick.
6. Add hydraulic oil through the dipstick tube as
SERVICE PRECLEANER
needed. Do not overfill.
Service precleaner every 25 hours. Service more often
when operating in dirty or dusty conditions. See engine
manual for detailed instructions.
IMPORTANT: Fluid should be changed only if it is
contaminated.
GB - 12
CHECK ENGINE OIL COOLER
CHANGE OIL
Check engine oil cooler every 25 hours. Check more
often when operating in dirty or dusty conditions. See
engine manual for detailed instructions.
Change engine oil every 100 hours. See engine manual
for detailed instructions.
CLEAN COOLING AREAS
Remove shrouds and clean cooling areas every 100
hours. Clean more often in dirty or dusty conditions. See
engine manual for detailed instructions.
CLEAN HYDRAULIC OIL COOLER
Blow out hydraulic oil cooler with compressed air every
25 hours of operation to remove dust and debris.
CHANGE ENGINE OIL FILTER
INSPECT MUFFLER/SPARK ARRESTOR
Change oil filter every 200 hours. See engine manual for
detailed instructions.
Inspect muffler and spark arrestor every 50 hours.
Replace muffler if corroded.
CHECK SPARK PLUGS
REPLACE AIR CLEANER
Check condition of spark plugs and spark plug gap every
200 hours. See engine manual for detailed instructions.
Replace air cleaner every 100 hours. Replace more
often when operating in dirty or dusty conditions. See
engine manual for detailed instructions.
SERVICE AND ADJUSTMENTS
REPLACING THE DRIVE BELT
1. Stop engine and remove key.
2. Disengage PTO.
ADJUSTING NEUTRAL
Adjust neutral on hydraulic pump if tractor "creeps" when
direction control pedal is not depressed.
3. Remove remove mower belt from electric clutch
WARNING: The following adjustment requires
engine running and guards removed. Use
extreme caution when performing this
adjustment.
(see mower owner’s manual).
4. Remove idler spring and drive belt.
5. Place the new belt on the pump sheave, idler pulley
and engine sheave.
1. Shut off engine and remove key.
6. Reinstall idler spring.
2. Jack or hoist one of the drive wheels off the ground.
3. Start the engine. Do not engage parking brake.
4. Loosen adjusting bolt.
7. Reinstall mower belt. Adjust mower belt tension per
mower Owner/Operator Manual.
5. To correct forward creep, turn neutral bracket
clockwise.
6
1
To correct backward creep, turn neutral bracket
counterclockwise.
3
6. Retighten the adjusting bolt.
5
7. Ensure neutral switch sits in notch on plate. If it
does not, loosen plate bolt and rotate plate until
neutral switch sits in notch.
NOTE: This adjustment will affect the direction control
adjust angle.
4
2
1. Electric Clutch
2. Idler Spring
3. Drive Belt
4. Pump Sheave
5. Idler Pulley
6. Engine Sheave
Figure 6
OF3330
GB - 13
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTING PARKING BRAKE
To test parking brake:
4
1
1. Engage parking brake, shut off engine and remove
key.
3
5
3. Push unit. If unit can be moved, adjust parking
brake.
To adjust parking brake:
1. Loosen jam nuts.
2
1. Adjusting Bolt
2. Plate Bolt
3. Notch
4. Neutral Switch
5. Neutral Bracket
OF3350
Figure 7
ADJUSTING DIRECTION CONTROL PEDAL
2. Tighten adjustment nuts
to eliminate slack in
cables.
1. Remove jam nut from stop bolt and remove stop
bolt from frame.
1
2
3
4
3. Tighten jam nuts against
cable bracket.
5
1. Control Pedal
2. Stop Bolt
4. Jam Nut
5. Rod End
3. Adjustment Nut
Figure 9
OF3341
Figure 8
OF3360
2. Remove bolt and nut connecting rod end to
direction control pedal.
3. Turn rod end farther onto rod to angle pedal back.
Turn rod end farther off of rod to angle pedal
forward.
4. Check that pedal is in a comfortable position. Adjust
again if necessary.
5. Replace bolt and nut removed in step 2.
6. Reinstall stop bolt and turn adjustment nut until
pedal hits bolt when fully depressed forward.
7. Reinstall jam nut on stop bolt and tighten.
GB - 14
Download from Www.Somanuals.com. All Manuals Search And Download.
11. Reinstall battery into unit and connect positive (+)
STEERING BELT ADJUSTMENT
cable to battery first, then negative (-) cable.
1. Loosen idler nut.
12. Replace battery cover.
2. Tighten adjustment screw. Torque to 23 - 27 in. lbs.
(2.6 - 3 Nm).
CHANGING HYDRAULIC OIL
3. Tighten idler nut.
WARNING: HYDRAULIC FLUID UNDER
PRESSURE can penetrate skin and cause
severe burns that can result in death or serious
injury. ALWAYS keep body and hands away
from pin holes or nozzles which eject hydraulic
fluid under pressure. ALWAYS use paper or
cardboard and not hands to search leaks. Know
that all hydraulic fluid connections are tight and
all hydraulic hoses and lines are in good
condition BEFORE applying pressure to the
system. Foreign fluid injected into the skin must
be surgically removed within a few hours by a
doctor familiar with this form of injury or
gangrene may result.
Idler Nut
Adjustment
Screw
Capacity: 5 qt. (4.73 L)
Figure 10
OF3401
BATTERY
WARNING: AVOID INJURY. Read and
understand Battery Safety Rules in Safety
section before proceeding.
Charging Battery
ALWAYS follow information provided on battery by
battery manufacturer.
1. Stop engine and remove key.
2. Remove battery cover.
3. Disconnect negative (-) cable from battery first, then
positive (+) cable.
4. Loosen strap and remove battery.
5. Place battery on bench in well ventilated area
where electrolyte spill will not cause damage.
1. Park unit on a flat level surface, ensure the engine
is shut OFF, and the parking brake is set.
6. Initial Battery Setup - Remove caps and fill each
cell to level indicated with electrolyte at 1.265 .05
specific gravity and 80˚F (27˚C). Let battery stand
for thirty minutes. Check electrolyte level and add
more if necessary.
2. Place a suitable container under inlet hose.
3. Remove dipstick.
4. Remove inlet hose from filter housing.
5. Allow hydraulic oil to completely drain.
6. Install inlet hose on filter housing.
7. Connect positive (+) lead of charger to positive (+)
terminal, and negative (-) lead to negative (-)
terminal.
7. Add 15W-50 synthetic oil as needed to hydraulic
reservoir. Do not overfill.
8. Charge the battery at two and a half amps for ten
hours or until all cells are gassing freely and the
specific gravity is constant over three 30 minute
intervals.
IMPORTANT: Ensure hydraulic oil is at proper level
before starting engine.
8. Check hydraulic oil level.
9. Immediately after charging, check electrolyte level.
If low, add distilled water to bring cell up to required
level.
NOTE: Dispose of used oil at a certified recycling center.
10. Replace and tighten caps, wash off and dry battery.
GB - 15
Download from Www.Somanuals.com. All Manuals Search And Download.
STORAGE
ACCESSORIES
See your authorized Gravely Dealer to add these
optional accessories.
WARNING: AVOID INJURY. Read and
understand Storage Safety Rules in Safety
section before proceeding.
Part No.
Description
78900300
79200300
79200400
79200500
79200600
79200900
79201000
79201800
79207600
Steering Wheel Kit
SHORT TERM
Mulching Kit - 60" Mower
60" Mower Discharge Cover Kit
Mulching Kit - 50" Mower
50" Mower Discharge Cover Kit
Mulching Kit - 72" Mower
72" Mower Discharge Cover Kit
50" Bahia Baffle Kit
IMPORTANT: NEVER spray unit with water or store unit
outdoors.
Inspect unit for visible signs of wear, breakage or
damage.
Keep all nuts, bolts and screws properly tightened and
know unit is in safe working condition.
Store unit in a cool, dry protected area.
LONG TERM
72" & 60" Bahia Baffle Kit
Clean unit thoroughly and lubricate (see Maintenance).
Touch up all scratched painted surfaces.
ATTACHMENTS
Remove weight from wheels by putting blocks under
frame or axle.
See your authorized Gravely Dealer to add these
optional attachments.
When storing unit for extended periods of time, remove
all fuel from tank and carburetor (run dry). Refer to
engine manual.
Part No.
890012
890013
890014
Description
50" Fabricated Mower Deck
60" Fabricated Mower Deck
72" Fabricated Mower Deck
Clean and charge the battery. Charge battery every three
to four weeks when storing unit.
TROUBLESHOOTING
PROBLEM
PROBABLE CAUSE
CORRECTION
1. PTO engaged.
1. Disengage PTO.
No sound when
ignition key placed
in start position
2. Directional control pedal depressed.
3. Loose battery cables.
4. Discharged battery.
2. Place direction control pedal in neutral.
3. Check connections. Tighten battery cable clamps.
4. Recharge battery.
5. Blown fuse.
5. Replace fuse.
6. Neutral switch adjusted improperly.
6. Adjust neutral switch per Service and Adjustments.
1. Discharged battery.
2. Battery cable corroded.
3. Starter damaged.
1. Charge battery.
2. Clean battery connections.
3. See your dealer.
Starter clicks but
engine does not
start
1. Fuel tank empty.
2. Bad spark plug.
3. Engine problem.
1. Fill fuel tank.
2. See engine manual.
3. See engine manual.
Engine cranks but
does not start
1. Ignition ground wire disconnected.
2. Ignition switch failure.
1. Connect ground wire to clean, metal surface.
2. Replace ignition switch (see Dealer).
Engine continues to
run when ignition
key in off position
1. Attachment blocked.
2. Bad PTO switch.
1. Stop unit, remove key and clear attachment.
2. Replace switch (see Dealer).
Mower won’t
engage
GB - 16
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE PARTS
Description
SPECIFICATIONS
Part No.
Model Number
990018
990020
03621100
21416800
21535900
21410800
21397200
21535800
09246900
21525900
21536100
07237800
07235100
07234600
07237700
07235000
07234900
07224300
21416700
21536000
09246700
08899200
09246600
08899100
09097100
09254700
Battery
Description Name
PM 310
25 HP
PM 310
23 HP
Air Filter - Kohler
Air Filter - Kawasaki
Fuel Filter
Length
70" (177.8 cm)
Height
50.8" (129 cm)
Engine Oil Filter - Kohler
Engine Oil Filter - Kawasaki
Hydraulic Filter
Width
50.3" (127.8 cm)
Weight lbs. (kg.)
Battery
929 (422)
913 (415)
12 Volt
Spark Plug - Kohler (Qty. 2)
Spark Plug - Kawasaki (Qty. 2)
PTO (Engine to Deck) Belt (72")
PTO (Engine to Deck) Belt (60")
PTO (Engine to Deck) Belt (50")
Mower Drive Belt (72")
Mower Drive Belt (60")
Mower Drive Belt (50")
Hydraulic Belt
Brakes
Dynamic Disc - Parking
Steering
Turning Radius
Yoke
0˚
Tire Size - Front
- Rear
23 x 10.5 - 12 4 ply
16 - 6.50 - 8
Engine
Manufacturer
Kohler
Kawasaki
Cycle
4
Engine Power - HP
Starting System
Idle RPM
25 (18.6)
23 (17.2)
Element Precleaner - Kohler
Element Precleaner - Kawasaki
Blade 50"
electric
1800
Mulching Blade 50"
Blade 60"
Governed RPM
Fuel Tank Capacity
Fuel
3600
7.5 gal. (28.4L)
See engine manual.
See engine manual.
Mulching Blade 60"
Blade 72"
Crankcase
Capacity
Mulching Blade 72"
Engine Oil Type
Air Cleaner
See engine manual.
See engine manual.
See engine manual.
Hydrostatic Drive
Spark Plug Gap
Transmission
Speed - Forward
- Reverse
9.5 mph (15.2 kph)
5 mph (8 kph)
Hydraulic System
Lube
Mobil 15W-50 Synthetic
Drive Clutch
Hydrostatic
Tire Pressure
Front
12 - 15 PSI (82.8 - 103.4 kPa)
20 - 25 PSI (137.9 - 172.4 kPa)
Rear
Lift System
PTO
Hydraulic
Electric Clutch/Brake
GB - 17
Download from Www.Somanuals.com. All Manuals Search And Download.
2Year Limited Warranty
Ariens Company hereby warrants to the original consumer purchaser
that all Gravely Two-Wheel, Professional G, Pro, and ProMaster products
will be free from defects in material and workmanship for a period of
two (2) years from the date of purchase or 1000 hours, whichever
comes first.
Gravely Division of Ariens Company
655 West Ryan Street
P.O. Box 157
Brillion, WI 54110-0157
920-756-2141
Protection Plan
Ariens Company will repair or replace any part found upon examination
by the Ariens Company to be defective. Such repair or replacement
will be free of charge to the purchaser (labor and parts), except as
noted below.
Fax 920-756-2407
This warranty is subject to the following exceptions, conditions, and limitations:
Usage Requirement
The duration of this warranty shall be ninety days or 1000 hours, whichever comes first, if the product is rented or leased.
Purchaser’s Responsibilities
Exclusions (No Warranty)
• The purchaser must perform maintenance & minor adjustments
per the operator’s manual.
• The purchaser must notify Ariens Company or an authorized
Gravely service representative of the need for warranty service.
• The purchaser must transport the product to and from the place
of warranty repair.
• Normal maintenance, services, and normal replacement items,
such as spark plugs, oil, oil filters, air filters, mufflers, belts,
tires, shoes, runners, scraper blades, shear bolts, mower blades,
mower vanes, headlights, light bulbs, knives, etc. are not covered
by this warranty.
• Any equipment which has been altered, misused, misassembled,
improperly adjusted, neglected, or damaged by accident is not
covered by this warranty.
• Service completed by someone other than an authorized
Gravely dealer is not covered by this warranty.
• Any attachment not approved by Gravely nor any parts that
are not genuine Gravely service parts are not covered by this
warranty.
• Engines and engine accessories are covered only by the
warranty made by the engine manufacturer, and are not covered
by this warranty.
Product Registration
• The Gravely dealer must fill out and return the warranty
registration card to validate the warranty.
Service Parts and Accessories
• Service parts and accessories not purchased with the product
covered by this warranty are warranted to be free of defects
for a period of ninety (90) days following the date of purchase,
and will be replaced free of charge (except for labor).
• If the product is equipped with a Hydro-Gear transmission
and/or Hydro-Gear drive components, the Hydro-Gear
transmission and/or drive components are covered only by the
warranty made by Hydro-Gear, and are not covered by this
warranty.
• This warranty applies only to products purchased in the United
States (including Puerto Rico) and Canada. In all other
countries, contact place of purchase.
Service
• Warranty service must be done by an authorized Gravely dealer.
To find a Gravely dealer near you, contact Ariens Company.
Battery Warranty Prorated
• One to three months - Free replacement
• Four to twelve months - Prorated over 12 months
Ariens Company may from time to time change the design of its products. Nothing contained in this warranty shall be construed as
obligating Ariens Company to incorporate such design changes into previously manufactured products, nor shall such changes be
construed as an admission that previous designs were defective.
LIMITATION OF REMEDY AND DAMAGES
Ariens Company’s liability under this express warranty, and under
Ariens Company makes no warranty other than
any implied warranty that may exist, is limited to repair or replacement
DISCLAIMER OF FURTHER WARRANTY
what is expressly made in this warranty. If the law
of any defective part. In no event shall Ariens Company be liable
of your state provides that an implied warranty of
merchantability, or an implied warranty of fitness
for a particular purpose, applies to Ariens Company,
any such implied warranty is limited to the duration
of this express warranty.
for incidental, special, or consequential damages (including lost
profits). This warranty gives you specific legal rights. You may also
have other rights which vary from state to state. Some states do
not allow the exclusion of incidental or consequential damages, or
limitations on how long an implied warranty lasts, so the above
limitations and exclusions may not apply to you.
Form: GLW2-112701
GB - 18
Download from Www.Somanuals.com. All Manuals Search And Download.
GRAVELY
A Division of Ariens Company
655 West Ryan Street
P.O. Box 157
Brillion, WI 54110-0157
920-756-2141
Fax 920-756-2407
Download from Www.Somanuals.com. All Manuals Search And Download.
|