Instructions – Parts List
ALUMINUM AND STAINLESS STEEL
Huskyt 1590 Air-Operated
308441ZAD
ENG
Diaphragm Pumps
1.5–inch AODD pump for fluid transfer applications.
For professional use only.
See Models on page 2 for a list of pump models and descriptions.
120 psi (0.8 MPa, 8 bar) Maximum Fluid Working Pressure
120 psi (0.8 MPa, 8 bar) Maximum Air Input Pressure
Patent No.
CN ZL94102643.4
FR 9408894
JA 3517270
US 5,386,452
Important Safety Instructions
Read all warnings and instructions in this manual.
Save these instructions.
Model No. DB3777 shown
03263B
Download from Www.Somanuals.com. All Manuals Search And Download.
Symbols
Warning Symbol
Caution Symbol
WARNING
CAUTION
This symbol alerts you to the possibility of serious
injury or death if you do not follow the instructions.
This symbol alerts you to the possibility of damage to
or destruction of equipment if you do not follow the
instructions.
WARNING
EQUIPMENT MISUSE HAZARD
Equipment misuse can cause the equipment to rupture or malfunction and result in serious injury.
D This equipment is for professional use only.
INSTRUCTIONS
D Read all instruction manuals, tags, and labels before operating the equipment.
D Use the equipment only for its intended purpose. If you are not sure, call your Graco distributor.
D Do not alter or modify this equipment. Use only genuine Graco parts and accessories.
D Check equipment daily. Repair or replace worn or damaged parts immediately.
D Do not exceed the maximum working pressure of the lowest rated component in your system.
This equipment has a 120 psi (0.8 MPa, 8 bar) maximum working pressure at 120 psi (0.8
MPa, 8 bar) maximum incoming air pressure.
D Use fluids and solvents which are compatible with the equipment wetted parts. Refer to the
Technical Data section of all equipment manuals. Read the fluid and solvent manufacturer’s
warnings.
D Do not use 1,1,1–trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or
fluids containing such solvents in pressurized aluminum equipment. Such use could result in a
chemical reaction, with the possibility of explosion.
D
D
o
n
o
t
u
s
e
h
o
s
e
s
t
o
p
u
l
l
e
q
u
i
p
m
e
n
t
.
D Route hoses away from traffic areas, sharp edges, moving parts, and hot surfaces. Do not ex-
pose Graco hoses to temperatures above 82_ C (180_ F) or below –40_ C (–40_ F).
D
D
o
n
o
t
l
i
f
t
p
r
e
s
s
u
r
i
z
e
d
e
q
u
i
p
m
e
n
t
.
D
C
o
m
p
l
y
w
i
t
h
a
l
l
a
p
p
l
i
c
a
b
l
e
l
o
c
a
l
,
s
t
a
t
e
,
a
n
d
n
a
t
i
o
n
a
l
f
i
r
e
,
e
l
e
c
t
r
i
c
a
l
,
a
n
d
s
a
f
e
t
y
r
e
g
u
l
a
t
i
o
n
s
.
308441
3
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
TOXIC FLUID HAZARD
Hazardous fluid or toxic fumes can cause serious injury or death if splashed in the eyes or on the
skin, inhaled, or swallowed.
D
K
n
o
w
t
h
e
s
p
e
c
i
f
i
c
h
a
z
a
r
d
s
o
f
t
h
e
f
l
u
i
d
y
o
u
a
r
e
u
s
i
n
g
.
D
S
t
o
r
e
h
a
z
a
r
d
o
u
s
f
l
u
i
d
i
n
a
n
a
p
p
r
o
v
e
d
c
o
n
t
a
i
n
e
r
.
D
i
s
p
o
s
e
o
f
h
a
z
a
r
d
o
u
s
f
l
u
i
d
a
c
c
o
r
d
i
n
g
t
o
a
l
l
l
o
c
a
l
,
state and national guidelines.
D
A
l
w
a
y
s
w
e
a
r
p
r
o
t
e
c
t
i
v
e
e
y
e
w
e
a
r
,
g
l
o
v
e
s
,
c
l
o
t
h
i
n
g
a
n
d
r
e
s
p
i
r
a
t
o
r
a
s
r
e
c
o
m
m
e
n
d
e
d
b
y
t
h
e
f
l
u
i
d
and solvent manufacturer.
D Pipe and dispose of the exhaust air safely, away from people, animals, and food handling areas.
If the diaphragm fails, the fluid is exhausted along with the air. See Air Exhaust Ventilation on
page 9.
FIRE AND EXPLOSION HAZARD
Improper grounding, poor ventilation, open flames or sparks can cause a hazardous condition and
result in a fire or explosion and serious injury.
D
G
r
o
u
n
d
t
h
e
e
q
u
i
p
m
e
n
t
.
R
e
f
e
r
t
o
G
r
o
u
n
d
i
n
g
o
n
p
a
g
e
5
.
D If there is any static sparking or you feel an electric shock while using this equipment, stop
pumping immediately. Do not use the equipment until you identify and correct the problem.
D
P
r
o
v
i
d
e
f
r
e
s
h
a
i
r
v
e
n
t
i
l
a
t
i
o
n
t
o
a
v
o
i
d
t
h
e
b
u
i
l
d
u
p
o
f
f
l
a
m
m
a
b
l
e
f
u
m
e
s
f
r
o
m
s
o
l
v
e
n
t
s
o
r
t
h
e
f
l
u
i
d
being sprayed.
D Pipe and dispose of the exhaust air safely, away from all sources of ignition. If the diaphragm
fails, the fluid is exhausted along with the air. See Air Exhaust Ventilation on page 9.
D Keep the work area free of debris, including solvent, rags, and gasoline.
D Electrically disconnect all equipment in the work area.
D Extinguish all open flames or pilot lights in the work area.
D Do not smoke in the work area.
D Do not turn on or off any light switch in the work area while operating or if fumes are present.
D Do not operate a gasoline engine in the work area.
4
308441
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
General Information
Grounding
D The typical installation shown in Fig. 2 is only a
guide for selecting and installing system compo-
nents. Contact your Graco distributor for assistance
in planning a system to suit your needs.
WARNING
FIRE AND EXPLOSION HAZARD
This pump must be grounded. Before
operating the pump, ground the system
as explained below. Also, read the sec-
tion FIRE AND EXPLOSION HAZARD,
on page 4.
D
A
l
w
a
y
s
u
s
e
G
e
n
u
i
n
e
G
r
a
c
o
P
a
r
t
s
a
n
d
A
c
c
e
s
s
o
r
i
e
s
.
Refer to Product Data Sheet 305646.
To reduce the risk of static sparking, ground the pump
and all other equipment used or located in the pumping
area. Check your local electrical code for detailed
grounding instructions for your area and type of equip-
ment. Ground all of this equipment:
D Reference numbers and letters in parentheses refer
to the callouts in the figures and the parts lists on
pages 25–24.
D
L
i
f
t
t
h
e
p
u
m
p
b
y
g
r
a
s
p
i
n
g
t
h
e
o
u
t
l
e
t
m
a
n
i
f
o
l
d
(
1
)
D Pump: Connect a ground wire and clamp as shown
in Fig. 1. Loosen the grounding screw (W). Insert
one end of a 12 ga (1.5 mm@) minimum ground wire
(Y) behind the grounding screw and tighten the
screw securely. Connect the clamp end of the
ground wire to a true earth ground. Order Part
No. 222011 Ground Wire and Clamp.
securely. See Fig. 3 on page 8.
WARNING
TOXIC FLUID HAZARD
Hazardous fluid or toxic fumes can
cause serious injury or death if splashed
in the eyes or on the skin, inhaled, or
swallowed.
Y
1. Read TOXIC FLUID HAZARD on page 4.
2. Use fluids and solvents which are compatible
with the equipment wetted parts. Refer to the
Technical Data section of all equipment manu-
als. Read the fluid and solvent manufacturer’s
warnings.
W
02646B
Fig. 1
Tightening Screws Before First Use
D Air and fluid hoses: Use only grounded hoses with
a maximum of 500 ft (150 m) combined hose
length to ensure grounding continuity.
Before using the pump for the first time, check and
retorque all external fasteners. See Torque Se-
quence, page 28. After the first day of operation,
retorque the fasteners. Although pump use varies, a
general guideline is to retorque fasteners every two
months.
D
A
i
r
c
o
m
p
r
e
s
s
o
r
:
F
o
l
l
o
w
t
h
e
m
a
n
u
f
a
c
t
u
r
e
r
’
s
r
e
c
o
m
-
mendations.
D All solvent pails used when flushing: Follow the
local code. Use only metal pails, which are conduc-
tive. Do not place the pail on a non-conductive
surface, such as paper or cardboard, which inter-
rupts the grounding continuity.
D
F
l
u
i
d
s
u
p
p
l
y
c
o
n
t
a
i
n
e
r
:
F
o
l
l
o
w
t
h
e
l
o
c
a
l
c
o
d
e
.
308441
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
c. The air line filter (F) removes harmful dirt and
Mountings
moisture from the compressed air supply.
CAUTION
The pump exhaust air may contain contaminants.
Ventilate to a remote area if the contaminants
could affect your fluid supply. See Air Exhaust
Ventilation on page 9.
2. Install a grounded, flexible air hose (A) between
the accessories and the 1/2 npt(f) pump air inlet
(N). See Fig. 3. Use a minimum 1/2 in. (13 mm) ID
air hose. Screw an air line quick disconnect cou-
pler (D) onto the end of the air hose (A), and screw
the mating fitting into the pump air inlet snugly. Do
not connect the coupler (D) to the fitting until you
are ready to operate the pump.
1. Be sure the mounting surface can support the
weight of the pump, hoses, and accessories, as
well as the stress caused during operation.
Installation of Remote Pilot Air Lines
2. For all mountings, be sure the pump is bolted
directly to the mounting surface.
1. Refer to Parts Drawings. Connect air line to pump
as in preceding steps.
3. For ease of operation and service, mount the
pump so the air valve cover (2), air inlet, and fluid
inlet and outlet ports are easily accessible.
2. Connect 1/4 in. O.D. tubing to push type connec-
tors (14) on air motor of pump.
4. Rubber Foot Mounting Kit 236452 is available to
reduce noise and vibration during operation.
NOTE: by replacing the push type connectors, other
sizes or types of fittings may be used. The new fittings
will require 1/8 in. npt threads.
Air Line
3. Connect remaining ends of tubes to external air
signal, such as Graco’s Cycleflo (P/N 195264) or
Cycleflo II (P/N195265) controllers.
WARNING
A bleed-type master air valve (B) is required in
your system to relieve air trapped between this
valve and the pump. Trapped air can cause the
pump to cycle unexpectedly, which could result in
serious injury, including splashing in the eyes or on
the skin, injury from moving parts, or contamination
from hazardous fluids. See Fig. 2.
NOTE: the air pressure at the connectors must be at
least 30% of the air pressure to the air motor for the
pump to operate.
Fluid Suction Line
1. Use grounded fluid hoses (G). The pump fluid
inlet (R) is 1–1/2 in. npt(f). Screw the fluid fitting
into the pump inlet securely.
1. Install the air line accessories as shown in Fig. 2.
Mount these accessories on the wall or on a
bracket. Be sure the air line supplying the acces-
sories is grounded.
2. If the fluid inlet pressure to the pump is more than
25% of the outlet working pressure, the ball check
valves will not close fast enough, resulting in
inefficient pump operation.
a. Install an air regulator (C) and gauge to control
the fluid pressure. The fluid outlet pressure will
be the same as the setting of the air regulator.
b. Locate one bleed-type master air valve (B)
close to the pump and use it to relieve trapped
air. See the WARNING above. Locate the
other master air valve (E) upstream from all air
line accessories and use it to isolate them
during cleaning and repair.
3. At inlet fluid pressures greater than 15 psi
(0.1 MPa, 1 bar), diaphragm life will be shortened.
4. See the Technical Data on page 30 for maximum
suction lift (wet and dry).
6
308441
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
1. Use grounded fluid hoses (L). The pump fluid
Fluid Outlet Line
outlet (S) is 1–1/2 in. npt(f). Screw the fluid fitting
into the pump outlet securely.
WARNING
A fluid drain valve (J) is required to relieve pres-
sure in the hose if it is plugged. The drain valve
reduces the risk of serious injury, including splash-
ing in the eyes or on the skin, or contamination
from hazardous fluids when relieving pressure.
Install the valve close to the pump fluid outlet. See
Fig. 2.
2. Install a fluid drain valve (J) near the fluid outlet.
See the WARNING above.
3. Install a shutoff valve (K) in the fluid outlet line.
TYPICAL FLOOR-MOUNT INSTALLATION
KEY
A
B
Air supply hose
B
E
C F
Bleed-type master air valve
(required for pump)
Air regulator
Air line quick disconnect
Master air valve (for accessories)
Air line filter
Fluid suction hose
Fluid supply
Fluid drain valve (required)
Fluid shutoff valve
Fluid hose
C
D
E
F
G
H
J
A
K
L
S
D
K
L
R
S
Y
1.5 npt(f) fluid inlet port
1.5 npt(f) fluid outlet port
Ground wire (required; see page 5
for installation instructions)
Y
H
J
R
G
Muffler not included
on Model No. 253485
03265B
Fig. 2
308441
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Changing the Orientation of the Fluid Inlet
Fluid Pressure Relief Valve
and Outlet Ports
The pump is shipped with the fluid inlet (R) and outlet
(S) ports facing the same direction. See Fig. 3. To
change the orientation of the inlet and/or outlet port:
CAUTION
Some systems may require installation of a pres-
sure relief valve at the pump outlet to prevent
overpressurization and rupture of the pump or
hose. See Fig. 4.
1. Remove the screws (106) holding the inlet (102)
and/or outlet (103) manifold to the covers (101).
Thermal expansion of fluid in the outlet line can
cause overpressurization. This can occur when
using long fluid lines exposed to sunlight or ambi-
ent heat, or when pumping from a cool to a warm
area (for example, from an underground tank).
2. Reverse the manifold and reattach. Install the
screws, and torque according to the torque notes
in Fig. 3.
KEY
N
P
1/2 npt(f) air inlet port
Muffler. Air exhaust port
is 3/4 npt(f) . (Not included
on Model No. 253485)
1.5 npt(f) fluid
101Covers
Overpressurization can also occur if the Husky
pump is being used to feed fluid to a piston pump,
and the intake valve of the piston pump does not
close, causing fluid to back up in the outlet line.
102Fluid inlet manifold
103Fluid outlet manifold
106Manifold and cover screws
112 Bottom cover screws
R
S
inlet port
1.5 npt(f) fluid
outlet port
Apply medium-strength (blue) LoctiteR or equivalent to the
threads. Torque to 120–150 in-lb (14–17 NS m). See Torque
Sequence, page 28.
KEY
1
2
R
S
V
1.5 npt(f) fluid inlet port
1.5 npt(f) fluid outlet port
Pressure relief valve (Order Part No. 112119 for stainless steel
pumps)
Apply medium-strength (blue) LoctiteR or equivalent to the
threads. Torque to 190–220 in-lb (22–25 NS m). See Torque
Sequence, page 28.
1
2
Install valve between fluid inlet and outlet ports.
Connect fluid inlet line here.
103
3
Connect fluid outlet line here.
1
106
4
Muffler not included on Model No. 253485
3
S
S
N
106 2
V
1
101
2
112
2
P
R
102
4
R
03263B
Aluminum Model Shown
03461B
Fig. 4
Fig. 3
8
308441
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
The air exhaust port is 3/4 npt(f). Do not restrict the air
Air Exhaust Ventilation
exhaust port. Excessive exhaust restriction can cause
erratic pump operation.
WARNING
If the muffler (P) is installed directly to the air exhaust
port, apply PTFE thread tape or anti–seize thread
lubricant to the muffler threads before assembly.
FIRE AND EXPLOSION HAZARD
Be sure to read and follow the warnings
and precautions regarding TOXIC
FLUID HAZARD, and FIRE OR EXPLO-
SION HAZARD on page 4, before op-
erating this pump.
To provide a remote exhaust:
1. Remove the muffler (P) from the pump air exhaust
port.
Be sure the system is properly ventilated for your
type of installation. You must vent the exhaust to a
safe place, away from people, animals, food handl-
ing areas, and all sources of ignition when pumping
flammable or hazardous fluids.
2. Install a grounded air exhaust hose (T) and con-
nect the muffler (P) to the other end of the hose.
The minimum size for the air exhaust hose is 3/4
in. (19 mm) ID. If a hose longer than 15 ft (4.57 m)
is required, use a larger diameter hose. Avoid
sharp bends or kinks in the hose. See Fig. 5.
Diaphragm failure will cause the fluid being
pumped to exhaust with the air. Place an appropri-
ate container at the end of the air exhaust line to
catch the fluid. See Fig. 5.
3. Place a container (U) at the end of the air exhaust
line to catch fluid in case a diaphragm ruptures.
VENTING EXHAUST AIR
KEY
A
B
Air supply line
Bleed-type master air valve
(required for pump)
C
D
E
F
Air regulator
Air line quick disconnect
Master air valve (for accessories)
Air line filter
Muffler (not included on
Model No. 253485)
E
F
C
B
A
P
T
U
Grounded air exhaust hose
Container for remote air exhaust
D
T
U
P
03267A
Fig. 5
308441
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
NOTE: If the fluid inlet pressure to the pump is more
Pressure Relief Procedure
than 25% of the outlet working pressure, the ball check
valves will not close fast enough, resulting in inefficient
pump operation.
WARNING
PRESSURIZED EQUIPMENT HAZARD
The equipment stays pressurized until pressure is
manually relieved. To reduce the risk of serious
injury from pressurized fluid, accidental spray from
the gun or splashing fluid, follow this procedure
whenever you:
4. Place the end of the fluid hose (L) into an appropri-
ate container.
5. Close the fluid drain valve (J). See Fig. 2.
6. Close the pump air regulator (C). Open all bleed-
type master air valves (B, E).
D Are instructed to relieve pressure,
D Stop pumping,
D Check, clean or service any system equipment,
D Install or clean fluid nozzles.
7. If the fluid hose has a dispensing device, hold it
open while continuing with the following step.
8. Slowly open the air regulator (C) until the pump
starts to cycle. Allow the pump to cycle slowly until
all air is pushed out of the lines and the pump is
primed.
1. Shut off the air to the pump.
2. Open the dispensing valve, if used.
If you are flushing, run the pump long enough to
thoroughly clean the pump and hoses. Close the
air regulator. Remove the suction tube from the
solvent and place it in the fluid to be pumped.
3. Open the fluid drain valve to relieve all fluid pres-
sure, having a container ready to catch the drain-
age.
Operation of Remote Piloted Pumps
Flush the Pump Before First Use
1. Follow preceding steps 1 through 7 of Starting
and Adjusting Pump.
The pump was tested with lightweight oil, which is left
in the fluid passages to protect parts. To avoid contam-
inating your fluid with oil, flush the pump with a com-
patible solvent before using the equipment. Follow the
steps under Starting and Adjusting the Pump.
2. Open air regulator (C).
WARNING
The pump may cycle once before the external sig-
nal is applied. Injury is possible. If pump cycles,
wait until end before proceeding.
Starting and Adjusting the Pump
WARNING
TOXIC FLUID HAZARD
To reduce the risk of serious injury,
splashing in the eyes or on the skin, and
3. Pump will operate when air pressure is alternately
applied and relieved to push type connectors (14).
toxic fluid spills, never move or lift a
NOTE: Leaving air pressure applied to the air motor for
extended periods when the pump is not running may
shorten the diaphragm life. Using a 3–way solenoid
valve to automatically relieve the pressure on the air
motor when the metering cycle is complete prevents
this from occurring.
pump under pressure. If dropped, the fluid section
may rupture. Always follow the Pressure Relief
Procedure above before lifting the pump.
1. Be sure the pump is properly grounded. Refer to
Pump Shutdown
Grounding on page 5.
WARNING
To reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure at left.
2. Check all fittings to be sure they are tight. Be sure
to use a compatible liquid thread sealant on all
male threads. Tighten the fluid inlet and outlet
fittings securely.
3. Place the suction tube (if used) in the fluid to be
pumped.
At the end of the work shift, relieve the pressure.
10
308441
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Lubrication
Flushing and Storage
The air valve is designed to operate unlubricated,
however if lubrication is desired, every 500 hours of
operation (or monthly) remove the hose from the pump
air inlet and add two drops of machine oil to the air
inlet.
WARNING
To reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure on page 10.
CAUTION
Do not over-lubricate the pump. Oil is exhausted
through the muffler, which could contaminate your
fluid supply or other equipment. Excessive lubrica-
tion can also cause the pump to malfunction.
Flush the pump often enough to prevent the fluid you
are pumping from drying or freezing in the pump and
damaging it. Use a compatible solvent.
Always flush the pump and relieve the pressure before
storing it for any length of time.
Tightening Threaded Connections
Before each use, check all hoses for wear or damage,
and replace as necessary. Check to be sure all
threaded connections are tight and leak–free.
Check fasteners. Tighten or retorque as necessary.
Although pump use varies, a general guideline is to
retorque fasteners every two months. See Torque
Sequence, page 28.
308441
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
D
R
e
l
i
e
v
e
t
h
e
p
r
e
s
s
u
r
e
b
e
f
o
r
e
c
h
e
c
k
i
n
g
o
r
s
e
r
v
i
c
i
n
g
WARNING
the equipment.
To reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure on page 10.
D
C
h
e
c
k
a
l
l
p
o
s
s
i
b
l
e
p
r
o
b
l
e
m
s
a
n
d
c
a
u
s
e
s
b
e
f
o
r
e
disassembling the pump.
PROBLEM
CAUSE
SOLUTION
Pump cycles at stall or fails to hold
pressure at stall.
Worn check valve balls (301), seats Replace. See page 16.
(201) or o-rings (202).
Pump will not cycle, or cycles once Air valve is stuck or dirty.
and stops.
Disassemble and clean air valve.
See pages 14–15. Use filtered air.
Check valve ball (301) severely
worn and wedged in seat (201) or
manifold (102 or 103).
Replace ball and seat. See page
16.
Check valve ball (301) is wedged
Install Pressure Relief Valve
into seat (201), due to overpressur- (see page 8).
ization.
Dispensing valve clogged.
Clogged suction line.
Sticky or leaking balls (301).
Diaphragm ruptured.
Restricted exhaust.
Suction line is loose.
Diaphragm ruptured.
Relieve pressure and clear valve.
Inspect; clear.
Pump operates erratically.
Air bubbles in fluid.
Clean or replace. See page 16.
Replace. See pages 17–19.
Remove restriction.
Tighten.
Replace. See pages 17–19.
Loose inlet manifold (102), dam-
aged seal between manifold and
Tighten manifold bolts (106) or re-
place seats (201) or o-rings (202).
seat (201), damaged o-rings (202). See page 16.
Loose diaphragm shaft bolt (107).
Tighten or replace. See pages
17–19.
Damaged o-ring (108).
Replace. See pages 17–19.
12
308441
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
PROBLEM
CAUSE
SOLUTION
Fluid in exhaust air.
Diaphragm ruptured.
Loose diaphragm shaft bolt (107).
Replace. See pages 17–19.
Tighten or replace. See pages
17–19.
Damaged o-ring (108).
Replace. See pages 17–19.
Pump exhausts excessive air at
stall.
Worn air valve block (7), o-ring (6), Repair or replace. See pages
plate (8), pilot block (18), u-cups
(10), or pilot pin o-rings (17).
14–15.
Worn shaft seals (402).
Replace. See pages 17–19.
Pump leaks air externally.
Air valve cover (2) or air valve cover Tighten screws. See page 15.
screws (3) are loose.
Air valve gasket (4) or air cover
gasket (22) is damaged.
Inspect; replace. See pages 14–15,
20–21.
Air cover screws (25) are loose.
Tighten screws. See pages 20–21.
Pump leaks fluid externally from ball Loose manifolds (102, 103), dam-
check valves. aged seal between manifold and
Tighten manifold bolts (106) or re-
place seats (201) or o-rings (202).
seat (201), damaged o-rings (202). See page 16.
308441
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
Repairing the Air Valve
Tools Required
2
3
2
D
T
o
r
q
u
e
w
r
e
n
c
h
4{
H
D
T
o
r
x
(
T
2
0
)
s
c
r
e
w
d
r
i
v
e
r
o
r
7
m
m
(
9
/
3
2
i
n
.
)
s
o
c
k
e
t
wrench
D Needle-nose pliers
D O-ring pick
D
L
i
t
h
i
u
m
b
a
s
e
g
r
e
a
s
e
NOTE: Air Valve Repair Kits 236273 (aluminum center
housing models) and 255061 (sst center housing
models) are available. Refer to page 23. Parts included
in the kit are marked with a symbol, for example (4
{
H
)
.
Use all the parts in the kit for the best results.
Disassembly
1
WARNING
To reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure on page 10.
Muffler not included on
Model No. 253485
1
2
Torque to 50–60 in-lb
(5.6–6.8 NSm).
1. Relieve the pressure.
03268B
Fig. 6
2. With a Torx (T20) screwdriver or 7 mm (9/32 in.)
socket wrench, remove the six screws (3), air
valve cover (2), and gasket (4). See Fig. 6.
1
2
5
See Detail at right.
Grease.
3. Move the valve carriage (5) to the center position
and pull it out of the cavity. Remove the valve
{
{
H 6
H 7
2
3
3
Grease lower face.
block (7
{
H
)
a
n
d
o
-
r
i
n
g
(
6
{
H
)
f
r
o
m
t
h
e
c
a
r
r
i
a
g
e
.
Using a needle-nose pliers, pull the pilot block (18)
straight up and out of the cavity. See Fig. 7.
4. Pull the two actuator pistons (11) out of the bear-
ings (12). Remove the u-cup packings (10) from
the pistons. Pull the pilot pins (16) out of the
bearings (15). Remove the o-rings (17) from the
pilot pins. See Fig. 8.
18{
H
3
5 1
5. Inspect the valve plate (8H ) in place. If damaged,
use a Torx (T20) screwdriver or 7 mm (9/32 in.)
socket wrench to remove the three screws (3).
Remove the valve plate (8H ) and, on aluminum
center housing models only, remove the seal (9).
See Fig. 9.
11
6. Inspect the bearings (12, 15) in place. See Fig. 8.
The bearings are tapered and, if damaged, must
be removed from the outside. This requires disas-
sembly of the fluid section. See page 20.
7. Clean all parts and inspect for wear or damage.
Replace as needed. Reassemble as explained on
page 15.
03269
Fig. 7
14
308441
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
Reassembly
1
2
3
Insert narrow end first.
1. If you removed the bearings (12, 15), install new
ones as explained on page 20. Reassemble the
fluid section.
Grease.
Install with lips facing
narrow end of piston (11).
4
Insert wide end first.
2. On aluminum center housing models, install the
valve plate seal (9 H ) into the groove at the bot-
{
tom of the valve cavity. The rounded side of the
seal must face down into the groove. See Fig. 9.
2
3
10{
H
3. Install the valve plate (8H ) in the cavity. On alumi-
num center housing models, the plate is reversible,
so either side can face up. Install the three screws
(3), using a Torx (T20) screwdriver or 7 mm (9/32
in.) socket wrench. Tighten until the screws bottom
out on the housing. See Fig. 9.
4
11
12
4. Install an o-ring (17 H ) on each pilot pin (16).
{
Grease the pins and o-rings. Insert the pins into
the bearings (15), narrow end first. See Fig. 8.
5. Install a u-cup packing (10 H ) on each actuator
{
piston (11), so the lips of the packings face the
narrow end of the pistons. See Fig. 8.
1
17{
H
15 16
2
03270
Fig. 8
6. Lubricate the u-cup packings (10 H ) and actuator
{
1
2
Rounded side must face down
(aluminum center housing mod-
3
2
pistons (11). Insert the actuator pistons in the
bearings (12), wide end first. Leave the narrow
end of the pistons exposed. See Fig. 8.
els only).
Tighten screws until
8H
they bottom out on the
housing.
7. Grease the lower face of the pilot block (18 H ) and
{
install so its tabs snap into the grooves on the
ends of the pilot pins (16). See Fig. 7.
9{
H
1
8. Grease the o-ring (6 H ) and install it in the valve
{
block (7). Push the block onto the valve carriage
(5). Grease the lower face of the valve block. See
Fig. 7.
9. Install the valve carriage (5) so its tabs slip into the
grooves on the narrow end of the actuator pistons
(11). See Fig. 7.
10. Align the valve gasket (4 H ) and cover (2) with the
{
six holes in the center housing (1). Secure with six
screws (3), using a Torx (T20) screwdriver or 7
mm (9/32 in.) socket wrench. Torque to 50–60 in-lb
(5.6–6.8 NSm). See Fig. 6.
03271
Fig. 9
308441
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
Apply medium-strength (blue) LoctiteR or equivalent to the
Ball Check Valve Repair
1
threads. Torque to 120–150 in-lb (14–17 NS m). See Torque
Sequence, page 28.
Tools Required
D
T
o
r
q
u
e
w
r
e
n
c
h
Arrow (A) must point toward
outlet manifold (103).
2
D 13 mm socket wrench
D O-ring pick
3
4
Not used on some models.
Beveled seating surface
must face ball (301).
Disassembly
NOTE: A Fluid Section Repair Kit is available. Refer to
page 23 to order the correct kit for your pump. Parts
included in the kit are marked with an asterisk, for
example (201*). Use all the parts in the kit for the best
results.
1
106
103
NOTE: To ensure proper seating of the balls (301),
always replace the seats (201) when replacing the
balls. Also, on some models, replace the o-rings (202).
301*
WARNING
201* 4
To reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure on page 10.
202*
101
3
A
2
1. Relieve the pressure. Disconnect all hoses.
2. Remove the pump from its mounting.
3. Using a 13 mm socket wrench, remove the four
bolts (106) holding the outlet manifold (103) to the
fluid covers (101). See Fig. 10.
3
4. Remove the o-rings (202, not used on some
models), seats (201), and balls (301) from the
manifold.
301*
201*
202*
4
5. Turn the pump over and remove the inlet manifold
(102). Remove the o-rings (202, not used on some
models), seats (201), and balls (301) from the fluid
covers (101).
3
Reassembly
102
1. Clean all parts and inspect for wear or damage.
Replace parts as needed.
2. Reassemble in the reverse order, following all
notes in Fig. 10. Be sure the ball checks are
assembled exactly as shown. The arrows (A) on
the fluid covers (101) must point toward the outlet
manifold (103).
106 1
03272B
Fig. 10
16
308441
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
Diaphragm Repair
WARNING
Tools Required
To reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure on page 10.
D
T
o
r
q
u
e
w
r
e
n
c
h
D
1
3
m
m
s
o
c
k
e
t
w
r
e
n
c
h
D
1
5
m
m
s
o
c
k
e
t
w
r
e
n
c
h
(
a
l
u
m
i
n
u
m
m
o
d
e
l
s
)
o
r
1 in. socket wrench (stainless steel models)
1. Relieve the pressure.
D 19 mm open–end wrench
D O-ring pick
2. Remove the manifolds and disassemble the ball
check valves as explained on page 16.
D
L
i
t
h
i
u
m
-
b
a
s
e
g
r
e
a
s
e
Disassembly
3. Using a 13 mm socket wrench, remove the screws
(106 and 112) holding the fluid covers (101) to the
air covers (23). Pull the fluid covers (101) off the
pump. See Fig. 11.
NOTE: A Fluid Section Repair Kit is available. Refer to
page 23 to order the correct kit for your pump. Parts
included in the kit are marked with an asterisk, for
example (401*). Use all the parts in the kit for the best
results.
Apply medium-strength (blue) LoctiteR or equivalent to
1
the threads. Torque to 190–220 in-lb (22–25 NS m).
See Torque Sequence, page 28.
2
3
Arrow (A) must point toward air valve (B).
Muffler not included on Model No. 253485.
B
23
101
2
A
1
106
3
1
112
03273C
Fig. 11
308441
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
4. Loosen but do not remove the diaphragm shaft
a. Install the o-ring (108*) on the shaft bolt (107).
bolts (107), using a 15 mm socket wrench (1 in. on
stainless steel models) on both bolts. NOTE: This
step does not apply to pumps with overmolded
diaphragms.
b. Install the fluid side diaphragm plate (105) on
the bolt so the rounded side faces in, toward
the diaphragm (401).
c. On PTFE models only, install the PTFE dia-
phragm (403*). Make certain the side marked
AIR SIDE faces the center housing (1).
5. Unscrew one bolt from the diaphragm shaft (24)
and remove the o-ring (108), fluid side diaphragm
plate (105), PTFE diaphragm (403, used on PTFE
models only), diaphragm (401), and air side dia-
phragm plate (104). See Fig. 12.
d. Install the diaphragm (401*) on the bolt. Make
certain the side marked AIR SIDE faces the
center housing (1).
For overmolded diaphragms: Grip both dia-
phragms securely around the outer edge and
rotate counterclockwise. One diaphragm assembly
will come free and the other will remain attached to
the shaft. Remove the freed diaphragm and air
side plate.
e. Install the air side diaphragm plate (104) so
the recessed side faces the diaphragm (401).
f. Apply medium-strength (blue) LoctiteR or
equivalent to the bolt (107) threads. Screw the
bolt (107) into the shaft (24) hand tight.
6. Pull the other diaphragm assembly and the dia-
phragm shaft (24) out of the center housing (1).
Hold the shaft flats with a 19 mm open–end
g. For overmolded diaphragms: Assemble the air
side plate (104) onto the diaphragm (403). The
wide, radiused side of the plate must face the
diaphragm. Apply medium–strength (blue)
Loctite or equivalent to the threads of the
diaphragm assembly. Screw the assembly into
the shaft (24) hand tight.
wrench, and remove the bolt (107) from the shaft.
Disassemble the remaining diaphragm assembly.
For overmolded diaphragms: Pull the other dia-
phragm assembly and the diaphragm shaft (24)
out of the center housing (1). Hold the shaft flats
with a 19 mm open–end wrench and remove the
diaphragm and air side plate from the shaft.
3. Grease the length and ends of the diaphragm shaft
(24), and slide it through the housing (1).
4. Assemble the other diaphragm assembly to the
shaft as explained in step 2.
7. Inspect the diaphragm shaft (24) for wear or
scratches. If it is damaged, inspect the bearings
(19) in place. If the bearings are damaged, refer to
page 20.
5. Hold one shaft bolt (107) with a wrench and torque
the other bolt to 20–25 ft-lb (27–34 NSm) at 100
rpm maximum. NOTE: This step does not apply to
pumps with overmolded diaphragms.
8. Reach into the center housing (1) with an o-ring
pick and hook the u-cup packings (402), then pull
them out of the housing. This can be done with the
bearings (19) in place.
6. Align the fluid covers (101) and the center housing
(1) so the arrows (A) on the covers face the same
direction as the air valve (B). Apply medium-
strength (blue) LoctiteR or equivalent to the
threads of screws (106) and (112), and secure the
covers with the screws handtight. Install the
longer screws (112) in the bottom holes of the
covers. See Fig. 11. Using a 13 mm socket
wrench, torque the screws oppositely and evenly
to 190–220 in-lb (22–25 NSm). See Torque Se-
quence, page 28.
9. Clean all parts and inspect for wear or damage.
Replace parts as needed.
Reassembly
1. Install the shaft u-cup packings (402*) so the lips
face out of the housing (1). Lubricate the pack-
ings. See Fig. 12.
2. Install the diaphragm assembly on one end of the
shaft (24) as follows. For pumps with overmolded
diaphragms, go directly to step g.
7. Reassemble the ball check valves and manifolds
as explained on page 16.
18
308441
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
19
402*
1
105
2
5
107
403*
3
6
1
1
24
104
401*
4
7
3
03274A
03275A
Cutaway View, with Diaphragms in Place
Cutaway View, with Diaphragms Removed
24 4
7
104
401* 3
3
5
403*
105
2
1
24
4
108*
107
6
1
2
Lips face out of housing (1).
Rounded side faces diaphragm (401).
Air Side must face center housing (1).
Grease.
3
4
5
6
Used on pumps with PTFE diaphragms only.
Apply medium-strength (blue) LoctiteR or equiva-
lent. Torque to 20 to 25 ft-lb (27 to 34 N-m) at 100
rpm maximum.
7
8
8
Recessed side faces diaphragm (401).
Muffler not included on Model No. 253485.
03276C
Fig. 12
308441
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
7. Use a bearing puller to remove the diaphragm
Bearing and Air Gasket Removal
shaft bearings (19), air valve bearings (12) or pilot
pin bearings (15). Do not remove undamaged
bearings.
Tools Required
D
T
o
r
q
u
e
w
r
e
n
c
h
8. If you removed the diaphragm shaft bearings (19),
reach into the center housing (1) with an
o-ring pick and hook the u-cup packings (402),
then pull them out of the housing. Inspect the
packings. See Fig. 12.
D 10 mm socket wrench
D Bearing puller
D
O
-
r
i
n
g
p
i
c
k
D
P
r
e
s
s
,
o
r
b
l
o
c
k
a
n
d
m
a
l
l
e
t
Reassembly
1. If removed, install the shaft u-cup packings (402*)
Disassembly
NOTE: Do not remove undamaged bearings.
so the lips face out of the housing (1).
2. The bearings (12, 15, and 19) are tapered and can
only be installed one way. Insert the bearings into
the center housing (1), tapered end first. Using a
press or a block and rubber mallet, press-fit the
bearing so it is flush with the surface of the center
housing.
WARNING
To reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure on page 10.
3. Reassemble the air valve as explained on page
15.
1. Relieve the pressure.
4. Align the new air cover gasket (22) so the pilot pin
(16) protruding from the center housing (1) fits
through the proper hole (H) in the gasket.
2. Remove the manifolds and disassemble the ball
check valves as explained on page 16.
3. Remove the fluid covers and diaphragm assem-
blies as explained on page 17.
5. Align the air cover (23) so the pilot pin (16) fits in
the middle hole (M) of the three small holes near
the center of the cover. Apply medium-strength
(blue) LoctiteR or equivalent to the threads of
screws (25), and install the screws handtight. See
Fig. 13. Using a 10 mm socket wrench, torque the
screws oppositely and evenly to 130–150 in-lb
(15–17 NSm).
NOTE: If you are removing only the diaphragm shaft
bearing (19), skip step 4.
4. Disassemble the air valve as explained on page
14.
5. Using a 10 mm socket wrench, remove the screws
(25) holding the air covers (23) to the center
housing (1). See Fig. 13.
6. Install the diaphragm assemblies and fluid covers
as explained on page 17.
6. Remove the air cover gaskets (22). Always replace
the gaskets with new ones.
7. Reassemble the ball check valves and manifolds
as explained on page 16.
20
308441
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
12
1
2
3
Insert bearings tapered end first.
2
1
Press-fit bearings flush with surface of center housing (1).
Apply medium-strength (blue) LoctiteR or equivalent. Torque
to 130–150 in-lb (15–17 NSm).
4
Muffler not included on Model No. 253485.
03277
1
2
1
15
16
Detail of Air Valve Bearings
2
19
1
M
23
H
22
25
3
4
03278B
Fig. 13
308441
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Pump Matrix
Husky 1590 Aluminum and Stainless Steel Pumps, Series A
Your Model No. is marked on the pump’s serial plate. To determine the Model No. of your pump from the following
matrix, select the six digits which describe your pump, working from left to right. The first digit is always D,
designating Husky diaphragm pumps. The remaining five digits define the materials of construction. For example, a
pump with an aluminum air motor, aluminum fluid section, polypropylene seats, PTFE balls, and PTFE diaphragms
is Model No. D B 3 9 1 1. To order replacement parts, refer to the part lists on pages 25–24. The digits in the
matrix do not correspond to the ref. nos. in the parts drawing and lists.
Diaphragm
Pump
Air Motor
aluminum
aluminum
Fluid Section
aluminum
–
–
–
–
Seats
Balls
Diaphragms
TPE
232502*
TPE
acetal
253485*
aluminum
Buna–N
1 (not used)
Buna–N
1 (PTFE)
Buna–N
1 (PTFE)
D (for all pumps)
B aluminum
(standard)
1 (not used)
24B780*
C aluminum
(remote)
2 (not used)
–
2 (not used)
2 (acetal)
2 (not used)
24B781*
24G411*
T sst (standard) 3 (aluminum)
–
–
–
–
3 (316 sst)
3 (not used)
4 (440C sst)
5 (TPE)
3 (not used)
4 (not used)
5 (TPE)
U sst (remote)
4 (sst)
4 (17–4 PH sst)
5 (TPE)
5 (not used)
C (aluminum
BSPT)
6 (Santoprener )
6 (Santoprener )
6 (Santoprener )
D (sst BSPT)
–
–
–
–
–
7 (Buna–N)
7 (Buna–N)
7 Buna–N)
8 (Fluoroelastomer) 8 (Fluoroelastomer) 8 (Fluoroelastomer)
9 (polypropylene)
A (PVDF)
9 (not used)
A (not used)
G (Geolastr )
9 (not used)
A (not used)
G (Geolastr )
G (Geolastr )
246451 Stainless Steel Air Motor Conversion Kit
* 24B781 Stainless Steel Pump
This pump is the same as Model DB4311 except for
the serial plate and parts listed in the chart below.
Use kit 246451 and refer to manual 309643 (included
with kit) to convert from aluminum air motor to
stainless steel air motor.
* 24G411 Aluminum Pump
This pump is the same as Model DBC311 except for
the serial plate and parts listed in the chart below.
* 232502, Aluminum 1590 Pump, Series D
Model No. 232502 is a private-label aluminum 1590
pump. This pump is the same as Model No. DB3525
except for the label and:
* 24J358 Aluminum Pump
This pump is the same as Model DB3311 except for
the serial plate and parts listed in the chart below.
Ref. Nos. 10 and 402 are 115666 Packing, U–cup,
Fluoroelastomer
* 24J359 Aluminum Pump
This pump is the same as Model DB3321 except for
the serial plate and parts listed in the chart below.
Ref. No. 17 is 168518 O–ring, Fluoroelastomer
Use 243492 as the Air Valve Repair Kit
Ref. 106 is 112416 SCREW, SST; M10 x 1.5, 30 mm
Ref. 112 is 112417 SCREW, SST; M10 x 1.5; 90 mm
Ref.
No.
104
105
107
108
401
Part No. Description
Qty
2
* 253485, Aluminum 1590 Pump, Series A
Model No. 253485 is an aluminum 1590 pump. This
pump is the same as Model No. DB3777 except for the
label and that 253485 does not include Ref. No. 111
Muffler.
15H810
–––
PLATE, air side; alum.
not used
not used
not used
0
–––
0
–––
0
* 24B780 Stainless Steel Plus Pump
This pump is the same as Model DT4311 except for
the serial plate and parts listed in the chart below.
15G745 DIAPHRAGM, HD, overmolded;
PTFE/EPDM
2
22
308441
Download from Www.Somanuals.com. All Manuals Search And Download.
Repair Kit Matrix
For Husky 1590 Aluminum and Stainless Steel Pumps, Series A
Repair Kits may be ordered separately. To repair the air valve, order Part No. 236273 for aluminum center housing
models or Part No. 255061 for stainless steel center housing models (see page 24). Parts included in the Air Valve
Repair Kit are marked with a symbol in the parts list, for example (3).
To repair your pump, select the six digits which describe your pump from the following matrix, working from left to
right. The first digit is always D, the second digit is always 0 (zero), and the third is always B. The remaining three
digits define the materials of construction. Parts included in the kit are marked with an asterisk in the parts list, for
example (201*). For example, if your pump has polypropylene seats, PTFE balls, and PTFE diaphragms, order
Repair Kit D 0 B 9 1 1. If you only need to repair certain parts (for example, the diaphragms), use the 0 (null)
digits for the seats and balls, and order Repair Kit D 0 B 0 0 1. The digits in the matrix do not correspond to the
ref. nos. in the parts drawing and lists on pages 24–25.
Diaphragm
Pump
Null
Shaft O-ring
–
–
–
–
–
–
–
–
–
–
–
–
–
Seats
Balls
Diaphragms
0 (null)
D (for all pumps) 0 (for all pumps) B (PTFE)
0 (null)
0 (null)
1 (not used)
2 (not used)
3 (316 sst)
4 (17–4 PH sst)
5 (TPE)
1 (PTFE)
1 (PTFE)
2 (acetal)
3 (not used)
4 (440C sst)
5 (TPE)
2 (not used)
3 (not used)
4 (not used)
5 (TPE)
6 (Santoprener )
7 (Buna–N)
6 (Santoprener )
7 (Buna–N)
6 (Santoprener )
7 (Buna–N)
8 (Fluoroelastomer) 8 (Fluoroelastomer) 8 (Fluoroelastomer)
9 (polypropylene)
A (PVDF)
9 (not used)
A (not used)
G (Geolastr )
9 (not used)
A (not used)
G (Geolastr )
G (Geolastr )
Part No. 253627: Husky 1590 HD Overmolded PTFE/EPDM Diaphragm Repair Kit.
Part No. 289225: Husky 1590 HD Overmolded PTFE/EPDM Diaphragm Repair Kit,
with new air side diaphragm plates.
Part No. 24F398: Husky 1590 PTFE/Santoprene Backer Diaphragm Repair Kit,
for metal pumps.
308441
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts Drawing
2
3
5
J
{
4
11
J
{
1
0
6{
J
J
{
1
7
7{J
16
8
J
J
{
1
8
3
1
9{
16
17
{
J
12
14 }
110Y
10{J
11
22
106
23
20
103
15
25
111
1
301*
201*
1
402* 19
202* 1
106
13 }
24
Aluminum Model Shown
104
1
2
Not used on some models.
Used on PTFE models only.
101
401*
108*
Used on stainless steel models only.
3
1
403*
105
107
113
}
These parts are unique to remote piloted air motor, DC––––, DT––––
3
112
*
These parts are included in the Pump Repair Kit,
which may be purchased separately.
Refer to the Repair Kit Matrix on page 23 to
determine the correct kit for your pump.
*301
*201
202*
1
{
These parts are included in Air Valve Repair Kit 236273 (aluminum
center housing models), which may be purchased separately.
J
T
h
e
s
e
p
a
r
t
s
a
r
e
i
n
c
l
u
d
e
d
i
n
A
i
r
V
a
l
v
e
R
e
p
a
i
r
K
i
t
2
5
5
0
6
1
(
s
t
a
i
n
l
e
s
s
102
steel center housing models), which may be purchased separately.
Y
R
e
p
l
a
c
e
m
e
n
t
D
a
n
g
e
r
a
n
d
W
a
r
n
i
n
g
l
a
b
e
l
s
,
106
tags and cards are available at no cost.
03279C
24
308441
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
Air Motor Parts List (Matrix Column 2)
Ref.
Digit No.
Ref.
Digit No.
Part No. Description
Qty
Part No. Description
Same as B with the following exceptions
Qty
B
1
2
3
188838
188854
116344
HOUSING, center;
aluminum
1
C
1
195921
HOUSING, center;
remote, aluminum
1
2
COVER, air valve;
aluminum
1
9
23
195918
COVER, air; remote
SCREW, mach, hex
flange hd; M5 x 0.8;
12 mm (0.47 in.)
T
Same as B with the following exceptions
1
15K009
15K696
15H178
HOUSING, center;
stainless steel
1
1
1
4
5
6
7
8
9
{
H
188618
188855
108730
188616
188615
188617
112181
188612
188613
104765
115671
GASKET, cover; foam
CARRIAGE; aluminum
O-RING; nitrile
1
1
1
1
1
1
2
2
2
2
2
2
COVER, air valve;
stainless steel
{
{
H
H
PLATE, air valve;
stainless steel
8
9
H
BLOCK, air valve; acetal
PLATE, air valve; sst
SEAL, valve plate; buna-N
PACKING, u-cup; nitrile
PISTON, actuator; acetal
BEARING, piston; acetal
PLUG, pipe; headless
–
–
–
2
{
H
23
15A739
COVER, air; stainless
steel
10
11
12
{
H
25
112178
SCREW; M8 x 1.25;
25 mm (1 in.), stainless
steel
12
U
Same as B with the following exceptions
13}
14}
FITTING, connector;
male
1
15K011
15K696
15H178
HOUSING, center;
remote, stainless steel
1
1
1
15
16
188611
188610
157628
188614
188609
116343
188603
189400
189245
115643
BEARING, pin; acetal
PIN, pilot; stainless steel
O-RING; buna-N
2
2
COVER, air valve;
stainless steel
2
PLATE, air valve;
stainless steel
8
9
H
17
18
19
20
22
23
24
25
{
{
H
H
2
BLOCK, pilot; acetal
BEARING, shaft; acetal
SCREW, grounding
1
–
–
–
2
2
23
15B795
COVER, air; remote,
stainless steel
1
25
112178
SCREW; M8 x 1.25;
25 mm (1 in.), stainless
steel
12
GASKET, air cover; foam
COVER, air; aluminum
SHAFT, diaphragm; sst
2
2
1
SCREW; M8 x 1.25;
12
25 mm (1 in.), aluminum
308441
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
Fluid Section Parts List (Matrix Column 3)
Ref.
Ref.
Digit No.
Part No. Description
Qty
2
Digit No.
Part No. Description
Qty
2
C
101
102
15A615
192078
COVER, fluid; aluminum
3
101
102
15A615
189402
COVER, fluid; aluminum
MANIFOLD, inlet;
aluminum; BSPT
1
MANIFOLD, inlet;
aluminum
1
103
104
105
106
107
108*
15A658
15K448
189843
115644
189410
MANIFOLD, outlet;
aluminum; BSPT
1
103
104
105
106
107
108*
15A616
15K448
189843
115644
189410
MANIFOLD, outlet;
aluminum
1
PLATE, air side;
aluminum
2
PLATE, air side;
aluminum
2
PLATE, fluid side;
carbon steel
2
PLATE, fluid side;
carbon steel
2
SCREW; M10 x 1.25;
35 mm (1.38 in.)
24
2
SCREW; M10 x 1.25;
35 mm (1.38 in.)
24
2
BOLT; M12 x 1.75;
55 mm (2.17 in.); 316 sst
BOLT; M12 x 1.75;
55 mm (2.17 in.); 316 sst
104319
188970
102656
115645
O-RING; PTFE
LABEL, warning
MUFFLER
2
1
1
4
104319
188970
102656
O-RING; PTFE
LABEL, warning
2
1
1
110
111
112
Y
110
111
Y
MUFFLER (not used on
Model No. 253485)
SCREW; M10 x 1.50;
90 mm (3.54 in.)
112
115645
SCREW; M10 x 1.50;
90 mm (3.54 in.)
4
D
101
102
194169
195574
COVER, fluid; sst
2
1
4
101
102
103
104
194169
194170
194221
15K448
COVER, fluid; sst
2
1
1
2
MANIFOLD, inlet; sst;
BSPT
MANIFOLD, inlet; sst
MANIFOLD, outlet; sst
103
104
195575
15K448
MANIFOLD, outlet; sst;
BSPT
1
2
PLATE, air side;
aluminum
PLATE, air side;
aluminum
105
106
189309
112416
PLATE, fluid side; sst
2
105
106
189309
112416
PLATE, fluid side; sst
2
SCREW; M10 x 1.25;
30 mm (1.18 in.); sst
24
SCREW; M10 x 1.25;
30 mm (1.18 in.); sst
24
107
189410
BOLT; M12 x 1.75;
55 mm (2.17 in.); 316 sst
2
107
189410
BOLT; M12 x 1.75;
55 mm (2.17 in.); 316 sst
2
108*
104319
188621
102656
112417
O-RING; PTFE
LABEL, warning
MUFFLER
2
1
1
4
108*
104319
188621
102656
112417
O-RING; PTFE
LABEL, warning
MUFFLER
2
1
1
4
110
111
112
Y
110
111
112
Y
SCREW; M10 x 1.50;
90 mm (3.54 in.); sst
SCREW; M10 x 1.50;
90 mm (3.54 in.); sst
113
114862
NUT, hex, M10, fhn
8
26
308441
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
Seat Parts List (Matrix Column 4)
Ball Parts List (Matrix Column 5)
Ref.
Ref.
Digit No.
Part No. Description
Qty
4
Digit No.
Part No. Description
Qty
1
2
4
301*
301*
301*
112419
112423
112420
BALL; PTFE
BALL; acetal
3
4
201*
189318
SEAT; 316 stainless
steel
4
4
202*
201*
112418
189319
O-RING; PTFE
4
4
BALL; 440C stainless
steel
4
SEAT; 17-4 stainless
steel
5
6
7
8
G
301*
301*
301*
301*
301*
112831
112421
15B490
15B489
114752
BALL; TPE
4
4
4
4
4
202*
201*
202
112418
189322
None
O-RING; PTFE
SEAT; TPE
4
4
0
4
4
4
0
4
0
4
4
4
4
4
4
BALL; Santoprene
BALL; Buna–N
5
6
7
8
9
A
G
Not Used
BALL; Fluoroelastomer
201*
202*
201*
202
189320
112418
15B266
None
SEAT; Santoprene
O-RING; PTFE
SEAT; Buna–N
Not used
BALL; Geolast
R
Diaphragm Parts List (Matrix Column 6)
Ref.
Digit No.
Part No. Description
Qty
1
401*
Not sold
DIAPHRAGM, backup;
2
201*
202
15B264
None
SEAT; Fluoroelastomer
Not used
separately polychloroprene (CR)
402*
403*
401*
402*
401*
112181
15K312
189425
112181
189426
PACKING, u-cup; nitrile
DIAPHRAGM; PTFE
DIAPHRAGM; TPE
2
2
2
2
2
201*
202*
201*
202*
201*
202*
193417
112418
189732
112418
194213
112418
SEAT; polypropylene
O-RING; PTFE
SEAT; PVDF
5
6
PACKING, u-cup; nitrile
O-RING; PTFE
DIAPHRAGM; Santo-
prene
SEAT; Geolast
R
402*
401*
402*
401*
112181
15B312
112181
15B501
PACKING, u-cup; nitrile
DIAPHRAGM; Buna–N
PACKING, u-cup; nitrile
2
2
2
2
O-RING; PTFE
7
8
DIAPHRAGM;
Fluoroelastomer
402*
401*
112181
194214
PACKING, u-cup; nitrile
2
2
G
DIAPHRAGM;
GeolastR
402*
112181
PACKING, u-cup; nitrile
2
* These parts are included in the pump repair kit, purchased
separately. See Repair Kit Matrix on page 23 to determine
the correct kit for your pump.
308441
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Torque Sequence
Always follow torque sequence when instructed to torque fasteners.
1. Left/Right Fluid Covers
3. Outlet Manifold
Torque bolts to 190–220 in–lb (22–25 NSm).
Torque bolts to 120–150 in–lb (14–17 NSm).
18
15
1
3
8
5
16
17
9
10
TOP VIEW
7
6
4
2
SIDE VIEW
2. Inlet Manifold
Torque bolts to 120–150 in–lb (14–17 NSm).
14
11
12
13
BOTTOM VIEW
28
308441
Download from Www.Somanuals.com. All Manuals Search And Download.
Dimensions
FRONT VIEW
PUMP MOUNTING HOLE PATTERN
197 mm
6.0 in.
(152.5 mm)
1/2 npt(f)
Air Inlet
3/4 npt(f)
Air Exhaust
6.0 in.
(152.5 mm)
B
C
A
268 mm
38 mm
1
152.5 mm
379.5 mm
Muffler not included on Model No. 253485.
1
SST Pumps
Alum. Pumps
16.81 in. (427 mm)
18.31 in. (465 mm)
19.56 in. (497 mm)
Dim.
A
16.25 in. (412.5 mm)
17.75 in. (451 mm)
19.0 in. (482.5 mm)
B
C
SIDE VIEW
5.23 in.
(132.5 mm)
1.5 npt(f) Outlet Port
45°
1.5 npt(f) Inlet Port
6.0 in.
(152.5 mm)
1
.45 in.
(11.5 mm)
10.46 in.
(265.5 mm)
7438B
308441
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Data
Maximum fluid working pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 psi
(0.8 MPa, 8 bar)
Air pressure operating range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20–120 psi
(0.14 –0.8 MPa, 1.4–8 bar)
Maximum air consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125 scfm
Air consumption at 70 psi/60 gpm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 scfm (see chart)
Maximum free-flow delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 gpm (378.5 l/min)
Maximum pump speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200 cpm
Gallons (Liters) per cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.5 (1.9)
Maximum suction lift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 ft (5.48 m) wet or dry
Maximum size pumpable solids . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3/16 in. (4.8 mm)
* Maximum noise level at 100 psi, full flow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94 dBa
* Sound power level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108 dBa
* Noise level at 70 psi, 50 cycles/min . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 dBa
Maximum operating temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150_ F (65.5_ C);
200_ F (93.3_ C) for models with PTFE diaphragms
Air inlet size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.5 npt(f)
Fluid inlet size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.5 npt(f)
Fluid outlet size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.5 npt(f)
Wetted parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Vary by Model. See pages 22–24.
Non-wetted external parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . aluminum, 302, 316 stainless steel, polyester (labels)
Weight
Aluminum pumps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33.5 lb (15.2 kg)
Stainless steel pumps with aluminum center section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 lb (32.7 kg)
Stainless steel pumps with stainless steel center section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86 lb (40 kg)
Geolast
R
is a registered trademarks of the ExxonMobil Chemical Co.
SantopreneR is a registered trademarks of the Monsanto Co.
Loctiter is a registered trademark of the Loctite Corporation.
*
Noise levels measured with the pump mounted on the floor, using Rubber Foot Kit 236452. Sound power
measured per ISO Standard 9216.
30
308441
Download from Www.Somanuals.com. All Manuals Search And Download.
Performance Chart
Example of Finding Pump Air Consumption and Air Pressure at a Specific Fluid Delivery and Discharge Head:
To supply 60 gpm (227 liters) fluid flow (horizontal scale) at 40 psi (0.28 MPa, 2.8 bar) discharge head pressure (vertical scale) re-
quires approximately 50 scfm (1.40 m#/min) air consumption at 70 psi (0.49 MPa, 4.9 bar) inlet air pressure.
feet
(meters)
psi
(MPa, bar)
280
120
(0.8, 8)
A
(85.3)
INLET AIR PRESSURES
A
B
C
D
120 psi air (0.8, 8 bar)
100 psi air (0.7, 7 bar)
70 psi air (0.49, 4.9 bar)
40 psi air (0.28, 2.8 bar)
240
100
(0.7, 7.0)
E
(73.2)
B
200
(61.0)
80
(0.56, 5.6)
AIR CONSUMPTION
F
160
E
F
20 scfm (0.56 m#/min)
40 scfm (1.12 m#/min)
60 scfm (1.68 m#/min)
80 scfm (2.24 m#/min)
C
D
(48.8)
60
(0.42, 4.2)
G
H
120
(36.6)
G
40
(0.28, 2.8)
80
(24.4)
20
40
(0.14, 1.4)
(12.2)
H
0
0
15
(57)
30
45
(170)
60
75
90
105
120
0
(114)
(227)
(284)
(341)
(397)
(454)
FLUID FLOW GPM (lpm)
TEST CONDITIONS
Pump tested in water with PTFE diaphragm and inlet
submerged.
KEY
FLUID PRESSURE AND FLOW
SCFM AIR CONSUMPTION
308441
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Graco Warranties
Graco Standard Husky Pump Warranty
Graco warrants all equipment manufactured by Graco and bearing its name to be free from defects in material and workmanship on the
date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco,
Graco will, for a period of five years from the date of sale, repair or replace any part of the equipment determined by Graco to be
defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written
recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by
faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or sub-
stitution of non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of
Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture,
installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for
verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The
equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect
in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and
transportation.
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT
NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other
remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any
other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within six years of the date
of sale.
Graco makes no warranty, and disclaims all implied warranties of merchantability and fitness for a particular purpose in connection
with accessories, equipment, materials or components sold but not manufactured by Graco. These items sold, but not manufactured
by Graco (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide
purchaser with reasonable assistance in making any claim for breach of these warranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment
hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract,
breach of warranty, the negligence of Graco, or otherwise.
FOR GRACO CANADA CUSTOMERS
The parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings
entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnais-
sent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires
exécutés, donnés ou intentés à la suite de ou en rapport, directement ou indirectement, avec les procedures concernées.
Extended Product Warranty
Graco warrants all Husky 205, 307, 515, 716, 1040, 1590, 2150, and 3275 air valve center sections to be free from defects in material
and workmanship for a period of fifteen years from date installed in service by the original purchaser. Normal wear of items such as
packings or seals are not considered to be defects in material and workmanship.
Five years
Six to Fifteen years
Graco will provide parts and labor.
Graco will replace defective parts only.
Graco Information
TO PLACE AN ORDER, contact your Graco distributor or call to identify the distributor closest to you:
Phone: 612–623–6921 or Toll Free: 1–800–328–0211 Fax: 612–378–3505
All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
Original instructions. This manual contains English. MM 308441
Graco Headquarters: Minneapolis
International Offices: Belgium, China, Japan, Korea
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441
Copyright 1995, Graco Inc. is registered to ISO 9001
Revised 02/2011
32
308441
Download from Www.Somanuals.com. All Manuals Search And Download.
|