Instructions–Parts List
HYDRA–SPRAYR
Monarkr and Presidentr
307619ZAA
Pumps
ENG
For airless and air–assisted spraying of finishing materials.
For professional use only.
Important Safety Instructions
Read all warnings and instructions in this manual. Save
these instructions.
See page 2 for Table of Contents
Part No. 223596, Series B 23:1 Ratio Monarkr Pump
with Part No. 223595 carbon steel severe–duty displacement pump*
with stainless steel glands, intake housing, piston valve, and ball stop
2760 psi (19 MPa, 190 bar) Maximum Fluid Working Pressure
120 psi (0.8 MPa, 8 bar) Maximum Air Input Pressure
II 1/2 G T3
ITS03ATEX11228
Part No. 237958, Series B 23:1 Ratio Monarkr Pump
with Part No. 239145 stainless steel
severe–duty displacement pump*
3450 psi (24 MPa, 238 bar) Maximum Fluid Working Pressure
150 psi (1.0 MPa, 10.4 bar) Maximum Air Input Pressure
II 1/2 G T3
ITS03ATEX11228
Part No. 239140, Series A 46:1 Ratio Presidentr Pump
with Part No. 239145 stainless steel
06936
severe–duty displacement pump*
4600 psi (32 MPa, 317 bar) Maximum Fluid Working Pressure
100 psi (0.7 MPa, 7 bar) Maximum Air Input Pressure
Model 239140
II 2 G T6
*
Severe–duty displacement pumps have abrasion–resistant
displacement rods and sleeves. Refer to Technical Data on
page 20 for information on the wetted parts.
02097
Model 223596
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
SKIN INJECTION HAZARD
Spray from the gun, hose leaks, or ruptured components can inject fluid into your body and cause
extremely serious injury, including the need for amputation. Fluid splashed in the eyes or on the skin
can also cause serious injury.
D Fluid injected into the skin might look like just a cut, but it is a serious injury. Get immediate
surgical treatment.
D Do not point the gun at anyone or at any part of the body.
D Do not put your hand or fingers over the spray tip.
D Do not stop or deflect leaks with your hand, body, glove or rag.
D Do not “blow back” fluid; this is not an air spray system.
D Always have the tip guard and the trigger guard on the gun when spraying.
D Check the gun diffuser operation weekly. Refer to the gun manual.
D Be sure the gun trigger safety operates before spraying.
D Lock the gun trigger safety when you stop spraying.
D Follow the Pressure Relief Procedure on page 8 whenever you: are instructed to relieve pres-
sure; stop spraying; clean, check, or service the equipment; and install or clean the spray tip.
D Tighten all fluid connections before operating the equipment.
D Check the hoses, tubes, and couplings daily. Replace worn, damaged, or loose parts immediately.
Permanently coupled hoses cannot be repaired; replace the entire hose.
D Use only Graco approved hoses. Do not remove any spring guard that is used to help protect the
hose from rupture caused by kinks or bends near the couplings.
MOVING PARTS HAZARD
Moving parts, such as the air motor piston, can pinch or amputate your fingers.
D Keep clear of all moving parts when starting or operating the pump.
D Before servicing the equipment, follow the Pressure Relief Procedure on page 8 to prevent the
equipment from starting unexpectedly.
307619
3
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
FIRE AND EXPLOSION HAZARD
Improper grounding, poor ventilation, open flames or sparks can cause a hazardous condition and
result in a fire or explosion and serious injury.
D Ground the equipment and the object being sprayed. Refer to Grounding on page 5.
D If there is any static sparking or you feel an electric shock while using this equipment, stop spray-
ing immediately. Do not use the equipment until you identify and correct the problem.
D Provide fresh air ventilation to avoid the buildup of flammable fumes from solvents or the fluid
being sprayed.
D Keep the spray area free of debris, including solvent, rags, and gasoline.
D Electrically disconnect all equipment in the spray area.
D Extinguish all open flames or pilot lights in the spray area.
D Do not smoke in the spray area.
D Do not turn on or off any light switch in the spray area while operating or if fumes are present.
D Do not operate a gasoline engine in the spray area.
TOXIC FLUID HAZARD
Hazardous fluid or toxic fumes can cause serious injury or death if splashed in the eyes or on the skin,
inhaled, or swallowed.
D Know the specific hazards of the fluid you are using.
D Store hazardous fluid in an approved container. Dispose of hazardous fluid according to all local,
state and national guidelines.
D Always wear protective eyewear, gloves, clothing and respirator as recommended by the fluid and
solvent manufacturer.
4
307619
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
NOTES:
D Pump: Use a ground wire and clamp. See Fig.1.
Loosen the grounding lug locknut (W) and washer
(X). Insert one end of a 12 ga (1.5 mm@) minimum
ground wire (Y) into the slot in lug (Z) and tighten
the locknut securely. Connect the other end of the
wire to a true earth ground. For a ground wire and
clamp, order Part No. 237569.
D Reference numbers and letters in parentheses in
the text refer to the callouts in the figures and
drawings.
D Always use Genuine Graco Parts and Accessories,
available from your Graco distributor. If you supply
your own accessories, be sure they are adequately
sized and pressure-rated to meet the system’s
requirements.
Z
Y
D Fig. 2 is only a guide for selecting and installing
system components and accessories. Contact your
Graco distributor for assistance in designing a
system to suit your particular needs.
Prepare the Operator
X
All persons who operate the equipment must be
trained in the safe, efficient operation of all system
components as well as the proper handling of all fluids.
All operators must thoroughly read all instruction
manuals, tags, and labels before operating the
equipment.
W
0720
Fig. 1
D Air and fluid hoses: Use only electrically conductive
hoses with 500 ft (150 m) maximum combined hose
length to ensure grounding continuity.
Prepare the Site
D Air compressor: Follow manufacturer’s
Ensure that you have an adequate compressed air
supply. Refer to the performance charts on pages 21
and 23 to find the air consumption of your sprayer.
recommendations.
D Spray gun or dispensing valve: Connect to a
properly grounded fluid hose and pump.
Mount the pump (A) to suit the type of installation
planned. The pump dimensions and mounting hole
layout are shown on page 19.
D Object being sprayed: Follow your local code.
D Fluid supply container: Follow your local code.
Keep the site clear of any obstacles or debris that
could interfere with the operator’s movement.
D Solvent pails used when flushing: Follow your local
code. Use only metal pails, which are conductive,
placed on a grounded surface. Do not place the
pail on a nonconductive surface, such as paper or
cardboard, which interrupts the grounding
continuity.
Have a grounded, metal pail available for use when
flushing the system.
Grounding
D To maintain proper grounding continuity when
flushing or relieving pressure, always hold the metal
part of the spray gun firmly to the side of a
grounded metal pail, then trigger the gun.
WARNING
FIRE AND EXPLOSION HAZARD
Before operating the pump, ground the
system as explained below. Also read
the section FIRE AND EXPLOSION
HAZARD on page 4.
307619
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Typical Installation
KEY
F
G
A
B
C
D
Pump
Wall bracket
Air line lubricator
Bleed-type master air valve (required for pump)
See Warning on page 7 for part number.
Pump air regulator
E
F
G
H
J
Air line filter
Bleed-type master air valve (for accessories)
Electrically conductive air supply hose
Fluid drain valve (required)
See Warning on page 7 for part numbers.
Fluid filter
H
K
L
M
N
P
Y
E
D
C
A
Y
Electrically conductive fluid supply hose
Spray gun
M
Fluid suction hose
Air Line Moisture Trap and Drain Valve
Ground wire (required)
Part No. 237569. See page 5 for installation instructions.
B
P
K
J
N
L
02098
Fig. 2
6
307619
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Air Line Accessories
System Accessories
Install the following accessories in the order shown in
Fig. 2, using adapters as necessary:
WARNING
D Air line lubricator (C)
A bleed-type master air valve (D) and a fluid drain
valve (J) are required in your system. These
accessories help reduce the risk of serious injury
including skin injection, splashing in the eyes or on
the skin, and injury from moving parts if you are
adjusting or repairing the pump.
Provides automatic air motor lubrication.
D Bleed-type master air valve (D)
Required in your system to relieve air trapped
between it and the air motor when the valve is
closed (see the WARNING at left). Be sure the
bleed valve is easily accessible from the pump, and
is located downstream from the air regulator (E).
The bleed-type master air valve relieves air trapped
between this valve and the pump after the air is
shut off. Trapped air can cause the pump to cycle
unexpectedly. Locate the valve close to the pump.
Order Part No. 113333.
D Air regulator (E)
Controls pump speed and outlet pressure by
adjusting the air pressure to the pump. Locate the
regulator close to the pump, but upstream from the
bleed-type master air valve (D).
The fluid drain valve assists in relieving fluid pres-
sure in the displacement pump, hose, and gun.
Triggering the gun to relieve pressure may not be
sufficient. Order one of the following:
D Air line filter (F)
Install an air line filter (F) and a moisture trap and
drain valve (P) to help remove moisture and
contaminants from the compressed air supply.
Part No. Description
238635
210657
210658
210659
239018
235992
1/4 npt (mbe), carbon steel
1/4 npt (mbe), carbon steel
3/8 npt (mbe), carbon steel
1/4 npt x 3/8 npt (mbe), carbon steel
1/4 npt (mbe), stainless steel
1/4 npt x 3/8 npt (mbe), stainless steel
D Second bleed-type air valve (G)
Isolates the air line accessories for servicing.
Locate upstream from all other air line accessories.
Fluid Line Accessories
Install the following accessories in the positions shown
in Fig. 2, using adapters as necessary:
Air and Fluid Hoses
Be sure all air and fluid hoses are properly sized and
pressure-rated for your system. Use only electrically
conductive air and fluid hoses. Use a 1/2 in. (13 mm)
I.D. (minimum) air hose (H) to supply air to the pump.
D Fluid drain valve (J)
Required in your system to relieve fluid pressure in
the hose and gun (see the WARNING at left).
Install the drain valve so that it points down and the
handle points up when it is opened.
Fluid hoses must have spring guards on both ends.
Connect a fluid hose (L) to the pump’s 3/8 npt(f) fluid
outlet. Use of a short whip hose between the main
fluid hose and the gun (M) allows freer gun movement.
Connect a fluid suction hose or tube (N) to the pump’s
3/4 npt(m) fluid intake.
D Fluid filter (K)
Filters harmful particles from the fluid.
D Spray gun (M)
Dispenses the fluid. The gun shown in Fig. 2 is an
airless spray gun.
307619
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Pressure Relief Procedure
Packing Nut/Wet-Cup
WARNING
WARNING
SKIN INJECTION HAZARD
The system pressure must be manually
relieved to prevent the system from
starting or spraying accidentally. Fluid
To reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure at left.
Keep the packing nut/wet-cup (104) filled with Graco
Throat Seal Liquid (TSL) or compatible solvent to help
prolong the packing life. Ensure weekly that the
packing nut is torqued to 18 to 20 ft-lb (24 to 27 N.m);
do not overtighten it. See Fig. 3 on page 11. Relieve
the pressure before adjusting the packing nut or
adding TSL.
under high pressure can be injected through the
skin and cause serious injury. To reduce the risk of
an injury from injection, splashing fluid, or moving
parts, follow the Pressure Relief Procedure
whenever you:
D are instructed to relieve the pressure,
D stop spraying,
D check or service any of the system equipment,
D or install or clean the spray tip.
Starting and Adjusting the Pump
Begin these steps before you install the spray tip.
1. Lock the gun trigger safety.
1. Ensure that the air regulator (E) and bleed-type
master air valve (D) are closed. See Fig. 2 on
page 6.
2. Shut off the air supply to the pump.
3. Close the bleed-type master air valve (required in
your system).
2. Connect a suction hose (N) to the pump’s fluid
inlet, or lower the pump into a fluid supply
container.
4. Unlock the gun trigger safety.
3. Hold a metal part of the spray gun (M) firmly to the
side of a grounded metal pail and hold the trigger
open.
5. Hold a metal part of the gun firmly to the side of a
grounded metal pail, and trigger the gun to relieve
pressure.
4. Open the pump’s bleed-type master air valve (D).
6. Lock the gun trigger safety.
5. Slowly open the air regulator (E) until the pump
starts (approximately 40 psi [0.28 MPa, 2.8 bar]).
7. Open the drain valve (required in your system),
and have a container ready to catch the drainage.
6. Cycle the pump slowly until all the air is pushed
out and the pump and hoses are fully primed.
8. Leave the drain valve open until you are ready to
spray again.
7. Release the spray gun trigger and lock the trigger
safety. The pump should stall against pressure
when you release the trigger.
If you suspect that the spray tip or hose is completely
clogged, or that pressure has not been fully relieved
after following the steps above, very slowly loosen the
tip guard retaining nut or hose end coupling and relieve
pressure gradually, then loosen it completely. Then
clear the tip or hose.
WARNING
To reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure at left.
Flush the Pump Before First Use
The pump is tested with lightweight oil, which is left in
to protect the pump parts. If the fluid you are using
may be contaminated by the oil, flush it out with a
compatible solvent before using the pump. If the pump
is being used to supply a circulating system, allow the
solvent to circulate until the pump is thoroughly
flushed. See Flushing the Pump on page 9.
8. Relieve the pressure.
9. Install the spray tip in the gun.
Continued on page 9.
8
307619
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Flushing the Pump
WARNING
COMPONENT RUPTURE HAZARD
To reduce the risk of overpressurizing
your system, which could cause
WARNING
FIRE AND EXPLOSION HAZARD
Before flushing, read the section FIRE
AND EXPLOSION HAZARD on page
4. Be sure the entire system and
flushing pails are properly grounded.
Refer to Grounding on page 5.
component rupture and serious injury,
never exceed the specified maximum air input
pressure to the pump (see Technical Data on
page 20).
10. Control the pump speed and fluid pressure with
the air regulator (E). Always use the lowest air
pressure necessary to get the desired results.
Higher pressure causes premature spray tip and
pump wear.
Flush with a fluid that is compatible with the fluid you
are pumping and with the wetted parts in your system.
Check with your fluid manufacturer or supplier for
recommended flushing fluids and flushing frequency.
Always flush the pump before fluid dries on the
displacement rod.
11. With the pump and lines primed, and with
adequate air pressure and volume supplied, the
pump starts and stops as the spray gun is opened
and closed. In a circulating system, the pump runs
continuously and speeds up or slows down as
supply increases or decreases until the air supply
is shut off.
CAUTION
Never leave water or water-base fluid in the pump
overnight. If you are pumping water-base fluid, flush
with water first, then with a rust inhibitor such as
mineral spirits. Relieve the pressure, but leave the
rust inhibitor in the pump to protect the parts from
corrosion.
CAUTION
Never allow the pump to run dry of the fluid being
pumped. A dry pump will quickly accelerate to a high
speed, possibly damaging itself. If your pump accel-
erates quickly, or is running too fast, stop it immedi-
ately and check the fluid supply. If the supply con-
tainer is empty and air has been pumped into the
lines, refill the container and prime the pump and the
lines with fluid, or flush and leave it filled with a
compatible solvent. Be sure to eliminate all air from
the fluid system.
WARNING
To reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure on page 8.
1. Relieve the pressure.
2. Remove the spray tip from the gun.
Shutdown and Care of the Pump
3. Hold a metal part of the gun firmly to the side of a
grounded metal pail.
WARNING
4. Start the pump. Always use the lowest possible
fluid pressure when flushing.
To reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure on page 8.
5. Trigger the gun.
For overnight shutdown, relieve the pressure, and
always stop the pump at the bottom of the stroke to
prevent the fluid from drying on the exposed
6. Flush the system until clear solvent flows from the
gun.
7. Relieve the pressure.
displacement rod and damaging the throat packings.
Always flush the pump before the fluid dries on the
displacement rod. See Flushing the Pump.
307619
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
1. Relieve the pressure.
WARNING
2. Check all possible problems and solutions before
disassembling pump.
To reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure on page 8.
Problem
Cause
Restricted line or inadequate air
Solution
Pump fails to operate.
Clear; increase air supply.
supply.
Insufficient air pressure; closed or
clogged air valves, etc.
Open; clean (be sure to use air
filter).
Exhausted fluid supply.
Refill; purge all air from pump and
fluid lines.
Damaged air valve; stalling.
Service air motor (see air motor
manual, supplied).
Dried fluid seizure of displacement
rod (103).
Clean, check or replace throat pack-
ings (114, 123); always stop pump at
bottom of stroke and keep wet-cup
filled with compatible solvent.
Pump operates but output is low on Restricted line or inadequate air
Clear; increase air supply.
both strokes.
supply.
Insufficient air pressure; closed or
clogged air valves, etc.
Open; clean (be sure to use air
filter).
Exhausted fluid supply.
Refill; purge all air from pump and
fluid lines.
Clogged fluid line, valves, etc.
Packing nut (104) is too tight.
Clear* (be sure to use fluid filter).
Loosen (see page 8).
Loose packing nut (104) or worn
throat packings (114, 123).
Tighten packing nut (see page 8);
replace throat packings.
Pump operates but output is low on Held open or worn intake valve.
downstroke.
Clear; service. See page 12.
Pump operates but output is low on Held open or worn fluid piston valve Clear; service. See page 12.
upstroke.
or packings (115, 124).
Erratic or accelerated operation.
Exhausted fluid supply.
Refill; purge all air from pump and
fluid lines.
Held open or worn intake valve.
Clear; service. See page 12.
Held open or worn fluid piston valve Clear; service. See page 12.
or packings (115, 124).
* To determine if the fluid hose or gun is obstructed, relieve the pressure and disconnect the fluid hose, and place
a container at the pump fluid outlet to catch any fluid. Turn on the air just enough to start the pump (about 20 to
40 psi [0.14 to 0.28 MPa, 1.4 to 2.8 bar]). If the pump starts when the air is turned on, the obstruction is in the
fluid hose or gun.
10
307619
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
Disconnecting the Displacement Pump
Reconnecting the Displacement Pump
1. Lubricate the o-ring (6) and check that it is in place
on the displacement rod (103).
WARNING
To reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure on page 8.
2. Orient the fluid outlet (R) to the air inlet (S) as
noted in step 2 under Disconnecting the
Displacement Pump. Position the displacement
pump (13) on the tie rods (10). See Fig. 3.
1. Flush the pump if possible. Stop the pump at the
bottom of its stroke. Relieve the pressure.
3. Screw the displacement rod (103) into the shaft of
the air motor (12) or the adapter (5, President
Pump only) until the pin holes are aligned. Screw
the locknuts (4) onto the tie rods (10) loosely.
Install the cotter pin (3).
2. Disconnect the air and fluid hoses. Remove the
pump from its mounting. Note the relative position
of the fluid outlet (R) to the air inlet (S). See Fig. 3.
3. Unscrew the tie rod locknuts (4) from the tie rods
(10). Remove the cotter pin (3). Carefully pull the
displacement pump (13) off the air motor (12).
Unscrew the displacement rod (103) from the air
motor (12) or adapter (5, President Pump only).
Inspect the o-ring (6).
4. Mount the pump and reconnect all hoses.
Reconnect the ground wire if it was disconnected
during repair. Torque the packing nut (104) to 18 to
20 ft-lb (24 to 27 N.m). Fill the wet-cup with Graco
Throat Seal Liquid or compatible solvent.
5. Tighten the tie rod locknuts (4) evenly, and torque
as specified in Fig. 3. Start the pump and run it at
about 40 psi (0.28 MPa, 2.8 bar) air pressure, to
check that it is operating properly.
4. Refer to page 12 for displacement pump service.
To service the air motor, refer to the separate air
motor manual, which is supplied.
1
2
3
4
Lubricate.
Monark Models
223596 (shown)
and 237958
Torque to 10 to15 ft-lb (14 to 20 N.m).
Torque to 20 to 30 ft-lb (27 to 41 N.m).
Torque to 18 to 20 ft-lb (24 to 27 N.m).
S
S
12
President Model
239140 (shown)
12
5
10 3
3
1
6
10
2
1
6
103
103
3
4
104
104
4
4
3
4
2
R
R
13
13
02099
06938
Fig. 3
307619 11
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
Reassembling
Displacement Pump Service
1. Lubricate the throat packings (114*, 123*). Install
the throat packing parts in the outlet housing (107)
one at a time, in the order shown in Detail A of Fig.
4. Be sure the lips of the v-packings face down,
lubricate the packing nut threads, and install the
packing nut finger tight.
Disassembling
When disassembling the pump, lay out all removed
parts in sequence to make reassembling easier. Refer
to Fig. 4.
NOTE: Repair Kits and Conversion Kits are available.
Refer to the parts list for your pump (pages 14 to 17).
For the best results, use all the new parts in the kit.
Parts included in the kit are marked with one asterisk
(for example, 3*).
2. If you removed the sleeve (106), reinstall it in the
outlet housing (107), making sure to replace the
gasket (120). To install the gasket, lay it flat in the
outlet housing (107) and use the sleeve to seat the
gasket against the shoulder of the outlet housing.
Be sure the tapered end of the sleeve faces down,
toward the pump intake.
Clean all the parts thoroughly when disassembling.
Check them carefully for damage or wear, and replace
parts as needed.
3. Lubricate the piston packings (115*, 124*). Install
the piston packing parts on the piston stud (102)
one at a time, in the order shown in Detail B of Fig.
4. Be sure the lips of the v-packings face up,
toward the threads of the piston stud.
1. Remove the displacement pump from the air motor
as explained on page 11.
2. Unscrew the intake valve housing (105) from the
outlet housing (107). If it is difficult to remove,
squirt penetrating oil around the threads and gently
tap around the valve housing with a plastic
hammer to loosen it.
4. Place the flats of the piston stud in a vise. Install
the piston ball (110*) on the piston and screw the
displacement rod (103) onto the piston valve
assembly. Torque to 35 to 40 ft-lb (47 to 54 N.m).
3. Remove the ball stop pin (113), o-ring retainer
(108), o-ring (109), ball guide (101), and ball (112).
5. Insert the displacement rod (103) into the bottom
of the outlet housing (107), being careful not to
scratch the sleeve (106). Push the rod straight up
until it protrudes from the packing nut (104).
4. Loosen the packing nut (104). Push the
displacement rod (103) down as far as possible,
and pull it out of the outlet housing (107), being
careful not to scratch the sleeve (106).
6. Install the ball (112*), guide (101), o-ring (109*),
retainer (108), and ball stop pin (113) in the intake
valve housing (105). Lubricate the intake valve
housing threads, and screw the intake valve
housing into the outlet housing (107). Torque to 55
to 65 ft-lb (75 to 88 N.m).
5. Secure the flats of the piston stud (102) in a vise.
Screw the displacement rod (103) off the piston
stud. Remove the ball (110), retainer (122),
packings (124, 115), and glands (117, 121).
6. Remove the packing nut (104), throat packings
(123, 114), glands (116, 118), and washer (119)
from the outlet housing (107).
7. Reconnect the displacement pump to the air motor
as explained on page 11.
7. Inspect all parts for damage. Clean all parts and
threads with a compatible solvent before
reassembling. Inspect the polished surfaces of the
displacement rod (103) and sleeve (106) for
scratches, scoring, or other damage, which can
cause premature packing wear and leaking. To
check, run a finger over the surface or hold the
part up to the light at an angle. Replace any worn
or damaged parts.
NOTE: If the sleeve (106) needs replacement and is
hard to remove, contact your Graco distributor.
12
307619
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
Lubricate.
Install the piston packings in the following order, with the
1
2
4
lips of the v-packings facing up: female gland (121*),
one PTFE v-packing (124*), four leather v-packings
(115*), male gland (117*), and packing retainer (122*).
Install the throat packings in the following order, with the
lips of the v-packings facing down: washer (119), male
gland (118*), four leather v-packings (114*), one PTFE
v-packing (123*), female gland (116*), and the packing
nut (104), install finger tight.
Torque to 35 to 40 ft-lb (47 to 54 N.m).
Torque to 55 to 65 ft-lb (75 to 88 N.m).
6
7
3
Tapered end of sleeve (106) must face down toward
pump intake.
See Reconnecting the Displacement Pump on page
11 for instructions on when to torque the packing nut to
18 to 20 ft-lb (24 to 27 N.m).
8
103
1
8
104
Detail A: Throat Packings
2
104
1
8
(Ref)
116*
107
(Ref)
1
*123
*114
118*
1
See
Detail A
1
120
119
3
106
107
4
Detail B: Piston Packings
103
(Ref)
102
*110
6
See
Detail B
6
102
(Ref)
*122
*117
113
108
101
*115
1
1 *124
*121
1
7
105
1
109*
06937
*112
Fig. 4
307619 13
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
Model 223596, Series B,
23:1 Ratio CST Monarkr Pump (shown)
includes items 3, 4, 6, 10, 12, and 13
Model 237958, Series B,
23:1 Ratio SST Monarkr Pump
includes items 3, 4, 6, 10, 12, and 14
12
Ref Part
No. No.
Description
Qty
3*
101946
PIN, cotter, stainless steel,
0.12 in. (3.2 mm) x 1.5 in. (38 mm)
NUT, lock, 3/8–16
SEAL, o-ring, buna-N
ROD, tie, carbon steel,
1
3
1
4
6
10
101566
154771
164722
10
3*
6
4.375 in. (112 mm) shoulder-to-shoulder
AIR MOTOR
see 307043 for parts
DISPLACEMENT PUMP ASSY,
carbon steel, for pump Model 223596
see page 15 for parts.
DISPLACEMENT PUMP ASSY,
stainless steel, for pump Model 237958
(not shown) see page 17 for parts.
3
1
12
13
222791
223595
4
1
1
14
239145
13, 14
*
This part is included in Repair Kit 239328, which may be
purchased separately. See pages 15 and 17 for
additional kit parts.
02099
14
307619
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
Model 223595, Series D
Carbon steel severe-duty displacement pump with stainless steel glands, intake housing, piston valve,
and ball stop
104
*116
*123
*114
103
*114
*114
*114
122*
117*
115*
115*
*118
119
115*
115*
124*
121*
110*
107
102
113
108
120
106
101
109*
112*
105
02101A
Ref
No.
Part
No.
Ref
No.
Part
No.
Description
Qty
Description
Qty
101
102
186187
223591
GUIDE, ball, intake, stainless steel
STUD, piston, stainless steel with
tungsten carbide seat
1
114*
115*
116*
117*
118*
119
164397
184300
186194
186195
186196
186197
164480
186198
186199
164913
164912
V-PACKING, throat, leather
V-PACKING, piston, leather
GLAND, throat, female, stainless steel 1
GLAND, piston, male, stainless steel
GLAND, throat, male, stainless steel
WASHER, flat, stainless steel
GASKET, flat, PTFE
4
4
1
1
1
103
104
105
24C508
206269
223593
ROD, displacement, stainless steel
PACKING NUT/WET-CUP, CST
HOUSING, valve, intake, SST
with tungsten carbide seat
SLEEVE, housing, stainless steel
HOUSING, outlet, carbon steel
RETAINER, o-ring, stainless steel
O-RING, PTFE
1
1
1
1
1
1
1
1
1
120
106
107
108
109*
110*
24C499
207011
186183
165052
105444
121*
122*
123*
124*
GLAND, piston, female, stainless steel 1
RETAINER, packing, stainless steel
V-PACKING, throat, PTFE
V-PACKING, piston, PTFE
TAG, warning (not shown)
1
1
1
1
BALL, 440C stainless steel,
0.31 in. (7.9 mm) dia.
125 Y 172479
1
112*
113
105445
186179
BALL, 440C stainless steel,
0.5 in. (13 mm) dia.
PIN, ball stop, intake, stainless steel
1
1
*
These parts are included in Repair Kit 239328, which may be purchased separately. See page 14 for additional parts.
Y Replacement danger and warning labels, tags, and cards are available for free.
307619 15
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
Model 239140, Series A,
46:1 Ratio SST Presidentr Pump
includes items 3, 4, 5, 6, 10, 12, and 13
Ref Part
No. No.
12
Description
Qty
3*
101946
PIN, cotter, stainless steel,
0.12 in. (3.2 mm) x 1.5 in. (38 mm)
NUT, lock, 3/8–16
ADAPTER
SEAL, o-ring, buna-N
ROD, tie, carbon steel,
6 in. (152 mm) shoulder-to-shoulder
AIR MOTOR
See 306982 for parts
DISPLACEMENT PUMP ASSY,
stainless steel, see page 17 for parts.
2
3
1
1
4
5
6
10
101566
191995
154771
191996
5
3
1
1
12
13
207352
239145
10
*3
*
This part is included in Repair Kit 239328, which may be
purchased separately. See page 17 for additional kit
parts.
6
4
13
06938A
16
307619
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
Model 239145, Series A
Stainless steel severe-duty displacement pump
104
*116
*123
103
*123
*114
*118
119
110*
122*
117*
115*
124*
124*
121*
102
107
113
108
101
120
106
109*
112*
105
06935
Ref
No.
Part
No.
Ref
No.
Part
No.
Description
Qty
Description
Qty
101
102
186187
223591
GUIDE, ball, intake, stainless steel
STUD, piston, stainless steel with
tungsten carbide seat
ROD, displacement, stainless steel
PACKING NUT/WET-CUP,
stainless steel
HOUSING, valve, intake, stainless
steel with tungsten carbide seat
SLEEVE, housing, stainless steel
HOUSING, outlet, stainless steel
RETAINER, o-ring, stainless steel
O-RING, PTFE
1
113
186179
164397
164715
186194
186195
186196
186197
164480
186198
186199
164913
164912
PIN, ball stop, intake, stainless steel
V-PACKING, throat, leather
V-PACKING, piston, leather
1
2
2
114*
115*
116*
117*
118*
119
1
1
103
104
24C508
223590
GLAND, throat, female, stainless steel 1
GLAND, piston, male, stainless steel
GLAND, throat, male, stainless steel
WASHER, flat, stainless steel
GASKET, flat, PTFE
1
1
1
1
1
105
223593
1
1
1
1
1
120
106
107
108
109*
110*
112*
24C499
239137
186183
165052
105444
105445
121*
122*
123*
124*
GLAND, piston, female, stainless steel 1
RETAINER, packing, stainless steel
V-PACKING, throat, PTFE
V-PACKING, piston, PTFE
TAG, warning (not shown)
1
2
2
1
BALL, 440C SST, 0.31 in. (7.9 mm) dia. 1
BALL, 440C SST, 0.5 in. (13 mm) dia. 1
125 Y 172479
*
These parts are included in Repair Kit 235636, which may be purchased separately. See page 16 for additional parts.
Y Replacement danger and warning labels, tags, and cards are available for free.
307619 17
Download from Www.Somanuals.com. All Manuals Search And Download.
Conversion Kits
PTFE Conversion Kit 236724
UHMWPE/Leather Conversion Kit 223674
For converting pumps to UHMWPE and leather
packings. Must be purchased separately.
For converting pumps to all PTFE packings. Must be
purchased separately.
Part
Part
No.
Description
Qty
No.
Description
Qty
101946
101545
165052
105444
PIN, cotter, stainless steel
PIN, cotter (for old-style ball checks)
O-RING, PTFE
BALL, 440C stainless steel,
0.31 in. (7.9 mm) dia.
BALL, 440C stainless steel,
0.5 in. (13 mm) dia.
GLAND, throat, female, stainless steel 1
GLAND, piston, male, stainless steel
GLAND, throat, male, stainless steel
GLAND, piston, female, stainless steel 1
RETAINER, packing, stainless steel
V-PACKING, piston, PTFE
V-PACKING, throat, PTFE
1
1
1
101946
101545
165052
105444
PIN, cotter, stainless steel
PIN, cotter (for old-style ball checks)
O-RING, PTFE
BALL, 440C stainless steel,
0.31 in. (7.9 mm) dia.
BALL, 440C stainless steel,
0.5 in. (13 mm) dia.
V-PACKING, throat, leather
V-PACKING, piston, leather
GLAND, throat, female, stainless steel 1
GLAND, piston, male, stainless steel
GLAND, throat, male, stainless steel
GLAND, piston, female, stainless steel 1
1
1
1
1
1
1
105445
105445
1
2
2
186194
186195
186196
186198
186199
164912
164913
164397
164715
186194
186195
186196
186198
186199
108455
108456
1
1
1
1
1
4
4
RETAINER, packing, stainless steel
V-PACKING, throat, UHMWPE
V-PACKING, piston, UHMWPE
1
2
2
PTFE/Leather Conversion Kit 235636
For converting pumps to PTFE and leather packings.
This is the standard repair kit for Model 223595
Displacement Pump, Series C and earlier. Must be
purchased separately.
PTFE/Leather Conversion Kit 239328
For converting pumps to leather packings.
Must be purchased separately.
Part
No.
Description
Qty
Part
No.
Description
Qty
101946
101545
165052
105444
PIN, cotter, stainless steel
PIN, cotter (for old-style ball checks)
O-RING, PTFE
BALL, 440C stainless steel,
0.31 in. (7.9 mm) dia.
BALL, 440C stainless steel,
0.5 in. (13 mm) dia.
V-PACKING, throat, leather
V-PACKING, piston, leather
GLAND, throat, female, stainless steel 1
GLAND, piston, male, stainless steel
GLAND, throat, male, stainless steel
GLAND, piston, female, stainless steel 1
RETAINER, packing, stainless steel
V-PACKING, piston, PTFE
1
1
1
101946
101545
165052
105444
PIN, cotter, stainless steel
PIN, cotter (for old-style ball checks)
O-RING, PTFE
BALL, 440C stainless steel,
0.31 in. (7.9 mm) dia.
BALL, 440C stainless steel,
0.5 in. (13 mm) dia.
V-PACKING, throat, leather
V-PACKING, piston, leather
GLAND, throat, female, stainless steel 1
GLAND, piston, male, stainless steel
GLAND, throat, male, stainless steel
GLAND, piston, female, stainless steel 1
RETAINER, packing, stainless steel
V-PACKING, piston, PTFE
1
1
1
1
105445
1
1
2
2
105445
164397
164715
186194
186195
186196
186198
186199
164912
164913
1
4
4
164397
184300
186194
186195
186196
186198
186199
164912
164913
1
1
1
1
1
2
2
1
1
1
V-PACKING, throat, PTFE
V-PACKING, throat, PTFE
18
307619
Download from Www.Somanuals.com. All Manuals Search And Download.
Dimensions
Model 223596 shown
Mounting Hole
Layout
A 4.38 in. (111.3 mm) diameter
B 2.5 in. (64 mm)
C 5.0 in. (127 mm)
D 0.28 in. (7.1 mm) diameter
Use Gasket
161023
(order separately)
C
D
A
D
(air inlet)
B
C
E
B
(fluid outlet)
A
F
(fluid intake)
02097
Model
Dimension 223596
Model
237958
Model
239140
A
B
C
10.8 in.
(274 mm)
10.9 in.
(277 mm)
10.8 in.
(274 mm)
15.2 in.
(386 mm)
15.2 in.
(386 mm)
16.8 in.
(426 mm)
28.8 in.
(732 mm)
28.8 in.
(732 mm)
31.6 in.
(802 mm)
D
E
F
3/8 npt(f)
3/8 npt(f)
3/4 npt(m)
3/8 npt(f)
3/8 npt(f)
3/4 npt(m)
1/2 npt(f)
3/8 npt(f)
3/4 npt(m)
307619 19
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Data
Category
Model 239140 SST Pres-
Model 223596 CST
Model 237958 SST
Monark
ident
Monark
Ratio
46:1
23:1
2760 psi
23:1
Maximum fluid
4600 psi
3450 psi
working pressure
(32 MPa, 317 bar)
(19 MPa, 190 bar)
(24 MPa, 238 bar)
Maximum air
input pressure
100 psi
(0.7 MPa, 7 bar)
120 psi
(0.8 MPa, 8 bar)
150 psi
(1.0 MPa, 10 bar)
Fluid flow at
60 cycles per minute
0.55 gpm
(2.1 liters/min)
0.4 gpm
(1.5 liters/min)
0.4 gpm
(1.5 liters/min)
Maximum pump
operating
180_F (82_C)
180_F (82_C)
180_F (82_C)
temperature
Weight
approx. 24 lb (11 kg)
approx. 24 lb (11 kg)
approx. 24 lb (11 kg)
Wetted parts
AISI 304, 316, 440C, and carbon steel; AISI 304,
AISI 304, 316, 440C, and
17–4 PH grades of stain-
less steel; tungsten
316, 420, 440C, and 17–4 17–4 PH grades of stain-
PH grades of stainless
steel; chrome; chrome
and zinc plating; tungsten
carbide; PTFE; leather
less steel; tungsten
carbide; PTFE; leather
carbide; PTFE; leather
Sound Pressure Levels (dBa)
(measured at 1 meter from unit)
Input Air Pressures at 15 cycles per minute
Air Motor
President
Monark
40 psi (0.28 MPa, 2.8 bar)
70 psi (0.48 MPa, 4.8 bar)
78.3 dB(A)
100 psi (0.7 MPa, 7 bar)
73.6 dB(A)
62.6 dB(A)
80.9 dB(A)
63.9 dB(A)
62.5 dB(A)
Sound Power Levels (dBa)
(tested in accordance with ISO 9614–2)
Input Air Pressures at 15 cycles per minute
Air Motor
President
Monark
40 psi (0.28 MPa, 2.8 bar)
87.4 dB(A)
70 psi (0.48 MPa, 4.8 bar)
92.1 dB(A)
100 psi (0.7 MPa, 7 bar)
94.6 dB(A)
69.5 dB(A)
70.7 dB(A)
71.0 dB(A)
20
307619
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Data
Model 223596 23:1 Ratio CST Monark Performance Chart
To find Fluid Outlet Pressure (psi/MPa/bar) at a specific fluid flow
To find Pump Air Consumption (m#/min or scfm) at a specific fluid
(lpm/gpm) and operating air pressure (psi/MPa/bar):
flow (lpm/gpm) and air pressure (psi/MPa/bar):
1. Locate desired flow along bottom of chart.
1. Locate desired flow along bottom of chart.
2. Follow vertical line up to intersection with selected fluid outlet
pressure curve (black). Follow left to scale to read fluid outlet
pressure.
2. Read vertical line up to intersection with selected air consumption
curve (dashes). Follow left to scale to read air consumption.
A
B
C
120 psi (0.8 MPa, 8 bar) air pressure
70 psi (0.49 MPa, 4.9 bar) air pressure
40 psi (0.28 MPa, 2.8 bar) air pressure
Monark 23:1 Fluid Outlet Pressure
Monark 23:1 Air Consumption
psi
MPa, bar
3000
scfm
m#/min
16
cycles per minute
cycles per minute
15
30
45
60
75
15
30
45
60
75
0.45
21, 210
A
A
B
2250
12
0.34
15.8, 158
1500
B
C
8
0.22
10.4,104
C
750
4
5.1, 51
.011
0
0
0.0
0.1
0.2
0.3
0.4
0.5
0.0
0.1
0.2
0.3
0.4
0.5
gpm
liters/minute
gpm
liters/minute
0.4
0.8
1.2
1.5
1.9
0.4
0.8
1.2
1.5
1.9
FLUID FLOW (TEST FLUID: NO. 10 WEIGHT OIL)
FLUID FLOW (TEST FLUID: NO. 10 WEIGHT OIL)
Model 237958 23:1 Ratio SST Monark Performance Chart
To find Fluid Outlet Pressure (psi/MPa/bar) at a specific fluid flow
(lpm/gpm) and operating air pressure (psi/MPa/bar):
To find Pump Air Consumption (m#/min or scfm) at a specific fluid
flow (lpm/gpm) and air pressure (psi/MPa/bar):
1. Locate desired flow along bottom of chart.
1. Locate desired flow along bottom of chart.
2. Follow vertical line up to intersection with selected fluid outlet
pressure curve (black). Follow left to scale to read fluid outlet
pressure.
2. Read vertical line up to intersection with selected air consumption
curve (dashes). Follow left to scale to read air consumption.
A
B
C
150 psi (1.0 MPa, 10 bar) air pressure
70 psi (0.49 MPa, 4.9 bar) air pressure
40 psi (0.28 MPa, 2.8 bar) air pressure
Monark 23:1 Fluid Outlet Pressure
Monark 23:1 Air Consumption
psi
MPa, bar
3500
scfm
m#/min
16
cycles per minute
cycles per minute
15
30
45
60
75
15
30
45
60
75
A
24.5, 245
0.45
3000
21, 210
A
B
12
0.34
2500
17.5, 175
2000
8
14, 140
1500
0.22
B
10.5, 105
1000
7,70
C
4
C
.011
500
3.5, 35
0
0
0.0
0.1
0.2
0.3
0.4
0.5
0.0
0.1
0.2
0.3
0.4
0.5
gpm
liters/minute
gpm
liters/minute
0.4
0.8
1.2
1.5
1.9
0.4
0.8
1.2
1.5
1.9
FLUID FLOW (TEST FLUID: NO. 10 WEIGHT OIL)
FLUID FLOW (TEST FLUID: NO. 10 WEIGHT OIL)
307619 21
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
22
307619
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Data
Models 239140 46:1 Ratio SST President Performance Chart
To find Fluid Outlet Pressure (psi/MPa/bar) at a specific fluid flow
(lpm/gpm) and operating air pressure (psi/MPa/bar):
To find Pump Air Consumption (m#/min or scfm) at a specific fluid
flow (lpm/gpm) and air pressure (psi/MPa/bar):
1. Locate desired flow along bottom of chart.
1. Locate desired flow along bottom of chart.
2. Follow vertical line up to intersection with selected fluid outlet
pressure curve (black). Follow left to scale to read fluid outlet
pressure.
2. Read vertical line up to intersection with selected air consumption
curve (dashes). Follow left to scale to read air consumption.
A
B
C
100 psi (0.7 MPa, 7 bar) air pressure
70 psi (0.49 MPa, 4.9 bar) air pressure
40 psi (0.28 MPa, 2.8 bar) air pressure
President 46:1 Fluid Outlet Pressure
President 46:1 Air Consumption
psi
MPa, bar
5000
scfm
m#/min
40
cycles per minute
41
cycles per minute
21
62
82
21
62
82
41
35, 350
4000
1.12
A
A
B
30
0.84
28, 280
3000
B
21, 210
20
0.56
2000
C
14, 140
10
C
1000
7,70
0
0.28
0
0.0
0.2
0.4
0.6
0.8
0.0
0.2
0.4
0.6
0.8
gpm
liters/minute
gpm
liters/minute
0.8
1.5
2.3
3.0
0.8
1.5
2.3
3.0
FLUID FLOW (TEST FLUID: NO. 10 WEIGHT OIL)
FLUID FLOW (TEST FLUID: NO. 10 WEIGHT OIL)
307619 23
Download from Www.Somanuals.com. All Manuals Search And Download.
Graco Standard Warranty
Graco warrants all equipment manufactured by Graco and bearing its name to be free from defects in material and workmanship on the
date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco,
Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be
defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written
recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by
faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or
substitution of non–Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility
of Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture,
installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for
verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The
equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect
in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and
transportation.
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT
NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other
remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any
other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the
date of sale.
Graco makes no warranty, and disclaims all implied warranties of merchantability and fitness for a particular purpose in connection
with accessories, equipment, materials or components sold but not manufactured by Graco. These items sold, but not manufactured
by Graco (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide
purchaser with reasonable assistance in making any claim for breach of these warranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment
hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract,
breach of warranty, the negligence of Graco, or otherwise.
FOR GRACO CANADA CUSTOMERS
The parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings
entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties
reconnaissent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures
judiciaires exécutés, donnés ou intentés à la suite de ou en rapport, directement ou indirectement, avec les procedures concernées.
Graco Information
TO PLACE AN ORDER, contact your Graco distributor or call to identify the distributor closest to you:
Phone: 612–623–6921 or Toll Free: 1–800–328–0211 Fax: 612–378–3505
All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
Original instructions. This manual contains English. MM 307619
Graco Headquarters: Minneapolis
International Offices: Belgium, China, Japan, Korea
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441
Copyright 1983, Graco Inc. is registered to ISO 9001
Revised 02/2011
24
307619
Download from Www.Somanuals.com. All Manuals Search And Download.
|