Graco Microscope Magnifier 24B771 User Manual

Kit Instructions/Parts

313840G

DataTrak Kits

For providing pump diagnostics and material usage information for diaphragm pumps.

Conversion Kits - DataTrak with Pulse Count and Runaway Protection

Husky 1050 - 24B777, 24B784, and 24B793

Husky 3300 - 24K861 and 24K862

Conversion Kits - DataTrak with Pulse Count

Husky 1050 and Husky 3300 - 24B794 and 24B795

Replacement Parts Kits 24B771, 24B772, 24B796, 24B798, 24K863, and 24K864

See page 3 for model information, including agency approvals.

Model 24B777 shown

Important Safety Instructions

Read all warnings and instructions

in the Husky 1050 or Husky 3300

Air-Operated Diaphragm Pump

manuals. Save all instructions.

ti14052a

Download from Www.Somanuals.com. All Manuals Search And Download.

DataTrak Kits

Conversion Kits

Use to add data monitoring capabilities to an existing pump.

Data Monitoring

Pulse

Count and

Husky

1050

Husky

3300

Diaphragm

Pump Material Protection Count

Runaway Pulse

24B777

24B795

24B784

24B794

24B793

24B794

24K861

24B795

24K862

24B794

✔*

Aluminum

✔

✔*

Polypropylene

✔

✔*

Conductive

Polypropylene

✔

* Kit includes replacement air valve compatible with solenoid.

Replacement Part Kits

Aluminum

Husky

1050A

Husky

3300A

Description

Solenoid/Reed Switch Assembly

(pulse count and runaway protection)

24B772

24B798

24K864

24B798

Reed Switch Assembly

(pulse count only)

Polypropylene and Conductive Polypropylene

Husky1050P Husky

or 1050C

24B771

24B796

3300P

Description

Solenoid/Reed Switch Assembly

(pulse count and runaway protection)

24K863

24B796

Reed Switch Assembly

(pulse count only)

313840G

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation

4. Select the Diagnostic Codes card that matches the

operator’s preferred language. Insert it in the inside

of the DataTrak cover for quick reference.

WARNING

SPECIAL CONDITIONS FOR SAFE USE

Equipment must comply with the following

conditions to avoid a hazardous condition

which can cause fire or explosion.

•

All label and marking material must be

cleaned with a damp cloth (or equiva-

lent).

•

The electronic monitoring system is

required to be grounded. See Ground-

ing instructions in your pump operation

manual.

ti14223a

5. DataTrak with runaway protection: Attach the sole-

noid (S) and bracket (4d) to the air valve. Use the

same screws (4c) that attach the air valve to the

manifold, as shown.

Prepare to Install

1. Relieve the pressure. Follow instructions in your

Operation manual.

2. Disconnect the air line to the pump.

Install the Kit

1. Mount the bracket

to the wall. Use

approximately

3/8 in. bolts or

screws.

2. Install the DataTrak

module (1) on the

bracket.

ti14058a

ti14055a

3. Conversion Kits include a new air valve that is com-

patible with the solenoid. Remove the old air valve

and gasket from the pump, and install the replace-

ment air valve and gasket.

313840G

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation

6. Use the screw provided to attach the reed switch

just behind the air inlet. Remove the muffler, if

a. The DataTrak pump icon should move when the

air motor changes direction.

needed, for easier access. Rotate the air inlet fitting

as needed so the wrench flat clears the reed switch.

b. The Grand Totalizer and Batch Totalizer should

advance.

4. DataTrak with runaway protection: Check for proper

runaway operation.

a. Run the air motor at a speed faster than the run-

away limit.

b. After 5 consecutive cycles,

the DataTrak should stop the

pump and display the run-

away diagnostic screen.

ti14056a

7. Connect the DataTrak cable to the 5-pin connector

on the reed switch. Reconnect the air line to the

motor.

c. To reset, turn the pressure off, then push

on the DataTrak module.

d. After resetting, turn on the air supply. The air

motor should run. Shut off the air until ready to

pump.

5-pin

connector

NOTE: If the DataTrak does not reset, turn air pressure

down, then use a screwdriver to push the solenoid

release button on the side of the air valve.

ti14054a

8. Secure DataTrack data cable. A plastic spiral con-

duit is provided to help prevent chafing.

ti14263a

5. Configure the DataTrak as needed. See page 7.

Check DataTrak Operation

1. Enable runaway

and set the runaway limit. See

Setup Mode, page 7.

2. Run the air motor at a speed slower than the run-

away limit.

3. Check for proper reed switch operation.

313840G

Download from Www.Somanuals.com. All Manuals Search And Download.

DataTrak Controls and Indicators

Key

AA Runaway Limit, in cycles per minute (user settable;

00=OFF)

AB Displacement (user settable)

PF Prime/Flush Key (Enables Prime/Flush mode. While in

Prime/Flush mode, runaway protection is disabled and the

batch totalizer [BT] will not count.) LED will flash while in

Prime/Flush mode.

/min,

AC Flow Rate Units (user settable to

gpm [US],

RK Reset Key (Resets faults. Press and hold for 3 seconds to

clear the batch totalizer.) Push to toggle between flow rate

and cycle rate.

CF Cycle/Flow Rate

BT Batch Totalizer (resettable)

gpm [Imperial], oz/min [US], oz/min [Imperial], l/min, or

cc/min)

AD LED (fault indicator when flashing)

AE Display

GT Grand Totalizer (not resettable)

Run Mode

AE, see details at right

ti8622b

TI11883a

Setup Mode

ti8623b

Fig. 1. DataTrak Controls and Indicators

313840G

Download from Www.Somanuals.com. All Manuals Search And Download.

DataTrak Operation

NOTE: The display (AE) will turn off after 1 minute to

save battery life. Press any key to wake up the display.

Run Mode

NOTE: DataTrak is factory set to 685 cc/cycle. This set-

ting is accurate for pumping water at a medium speed

on a Husky 1050 pump (approximately 20 gpm). The

DataTrak can be calibrated for use with a different Husky

model, for greater accuracy, for different pump speeds,

or for different viscosity fluids. See Calibration Proce-

dure, page 9.

Runaway

1. If pump runaway occurs, the runaway solenoid will

actuate, stopping the pump. The LED (AD) will flash

and the display (AE) will indicate a runaway condi-

tion. The display will cycle through four instruction

screens.

Setup Mode

1. See Fig. 1. Press and hold

Setup menu appears.

for 5 seconds until

2. To enter settings for flow rate units and displace-

ment, press to change the value, then to

save the value and move the cursor to the next data

field.

3. To enter setting for runaway (if equipped), enter

pump speed in cycles/min. The exact setting will

vary by pump speed and viscosity of fluid. Choose a

setting that is just above the fastest speed expected

during normal operation.

2. To reset the runaway solenoid, close the master air

valve. Wait for air to completely bleed off the air

motor.

3. Press

to clear the diagnostic code and reset the

NOTE: Set the value to zero to disable runaway protec-

tion or if your pump is not equipped with a runaway pro-

tection solenoid.

runaway solenoid.

4. Open master air valve to restart pump.

NOTE: A flashing LED indicates an error that must be

addressed. The Runaway mode will not stop a runaway

pump while the LED is flashing.

4. Move the cursor to the last field, then press

once more to exit Setup mode.

313840G

Download from Www.Somanuals.com. All Manuals Search And Download.

DataTrak Operation

NOTE: If the DataTrak does not reset, use a screwdriver

to push the solenoid release button on the side of the air

valve.

Counter/Totalizer

To reset the totalizer, press any key to wake up the dis-

play, then press and hold

for 3 seconds.

•

If AC is set to gallons or ounces, BT and GT dis-

play gallons.

If AC is set to liters or cc, BT and GT display

liters.

If AC is set to cycles, BT and GT display cycles.

NOTE: Press

to toggle between flow rate units and

cycles. A letter under the BT display indicates that both

BT and GT are displaying gallons (g) or liters (l). No let-

ter means both BT and GT are displaying cycles.

ti14263a

5. If the solenoid doesn’t actuate:

Display

a. Close the master air valve to stop the pump.

The display will show the Service Component 1

See Fig. 1. The display (AE) will turn off after 1 minute of

inactivity in Run mode or 3 minutes in Setup mode.

Press any key to wake up the display.

screen.

NOTE: DataTrak will continue to count cycles when dis-

play is off.

NOTE: The display (AE) may turn off if a high-level static

discharge is applied to the DataTrak. Press any key to

wake up the display.

b. See Table 1, Diagnostic Codes, on page 10.

NOTE: To disable runaway monitoring, go to setup

mode and set runaway value to 0 (zero). See Fig. 1.

Diagnostics

DataTrak can diagnose several problems with the pump.

When the monitor detects a problem, the LED (AD, Fig.

1) will flash and a diagnostic code will appear on the dis-

play. See Table 1, page 10.

Prime/Flush

1. See Fig. 1. To enter Prime/Flush mode, press any

key to wake up the display, then press

Prime/Flush symbol will appear in the display and

. The

To acknowledge the diagnosis and return to the normal

operating screen, press

once to wake up the display,

and once more to clear the diagnostic code screen.

the LED will flash

2. While in Prime/Flush mode, runaway protection is

disabled and the batch totalizer (BT) will not count.

3. To exit Prime/Flush mode, press any key to wake up

the display, then press

. The Prime/Flush sym-

bol will disappear from the display and the LED will

stop flashing.

313840G

Download from Www.Somanuals.com. All Manuals Search And Download.

DataTrak Operation

Calibration Procedure

1. Press and hold

appears.

for 5 seconds until Setup menu

2. Press

cycles/min.

once. Change flow rate units to

3. Return to Run Screen. Press and hold

seconds to reset batch totalizer.

for three

4. Dispense fluid from pump into a graduated con-

tainer.

5. Convert the actual volume dispensed to cubic centi-

meters (cc). See conversion chart.

Units Measured Multiply by

To get

Gallons (U.S.)

Gallons (Imp)

Liters

3785

4546

1000

946

29.57

28.41

16.39

28,317

473

Quarts

Ounces (U.S.)

Ounces (Imp)

Cubic inches

Cubic feet

Pints

6. Divide the actual volume dispensed (cc) by the num-

ber of cycles indicated on the DataTrak batch total-

izer display.

7. Press

to enter the Setup screen. Enter the

number from Step 6 in field 2 of the Setup screen.

313840G

Download from Www.Somanuals.com. All Manuals Search And Download.

DataTrak Operation

Table 1: Diagnostic Codes

Symbol

Code

Code Name

Diagnosis

Cause

Runaway

Pump running faster than Increased air pressure.

set runaway limit.

Increased fluid output.

Exhausted fluid supply.

E-3 Low Battery

E--4 Service

Battery voltage too low to Low battery. Replace battery;

stop runaway.

see page 11.

Problem with stopping

Damaged solenoid.

Component 1 runaway.

Damaged valve carriage.

Runaway protection may be

enabled with pump that is not

equipped with a runaway sole-

noid valve. Enter setup screen

and disable runaway protec-

tion.

E-4 Disconnected Solenoid is disconnected. Solenoid unplugged.

Solenoid

Damaged solenoid wires.

E-6 Blown Fuse

Fuse is blown. Replace

fuse; see page 11.

Faulty solenoid or solenoid

wiring.

Extreme temperatures (above

140°F [60°C]).

Runaway protection may be

enabled with pump that is not

equipped with a runaway sole-

noid valve. Enter setup screen

and disable runaway protec-

tion.

313840G

Download from Www.Somanuals.com. All Manuals Search And Download.

DataTrak Operation

Replace DataTrak Battery or Fuse

3. Remove two screws on back of module to access

battery.

4. Disconnect the used battery and replace with an

approved battery. See Fig. 4.

To reduce the risk of fire and explosion, the battery

and fuse must be replaced in a non-hazardous loca-

tion.

Table 2. Approved Batteries

Use only an approved replacement battery, shown in

Table 2, and an approved fuse, shown in Table 3. Use

of an unapproved battery or fuse will void Graco’s war-

ranty and Intertek and Ex approvals.

Energizer alkaline # 522

Varta alkaline # 4922

Ultralife lithium # U9V

Duracell alkaline # MN1604

Replace Battery

1. Unscrew cable from the reed switch assembly. See

Fig. 2.

ti14054a

Fig. 2. Disconnect DataTrak

2. Remove DataTrak module from bracket. See Fig. 3.

Take module to a non-hazardous location.

ti14053a

Fig. 3. Remove DataTrak

313840G

Download from Www.Somanuals.com. All Manuals Search And Download.

DataTrak Operation

Replace Fuse

Table 3. Approved Fuses

DataTrak Part

Fuse

1. Remove the screw, metal strap, and plastic holder.

Number

Series*

Required

2. Pull the fuse away from the board.

3. Replace with a new fuse.

A or B

C and later

24C580

24V216

24C580

24V216

289822

All other part

numbers

B and later

* Fig. 4 shows where to find the Series letter.

Solenoid Cable

Connection

Fuse

SensorCable

Connection

Series Letter

(last digit of code)

ti11994b

Battery

Fig. 4. DataTrak Battery and Fuse Location

313840G

Download from Www.Somanuals.com. All Manuals Search And Download.

DataTrak Operation

313840G

Download from Www.Somanuals.com. All Manuals Search And Download.

Parts

Conversion Kits, Cycle Count and Runaway Protection

Husky 1050 - 24B777 (Aluminum), 24B784 (Polypropylene), and 24B793 (Conductive Polypropylene)

Husky 3300 - 24K861 (Aluminum) and 24K862 (Polypropylene)

Aluminum

ti14225a

Plastic

Aluminum

ti14052a

ti14226a

313840G

Download from Www.Somanuals.com. All Manuals Search And Download.

Parts

Ref.

No. Part No. Description

Qty

No. Part No. Description

Qty

AIR VALVE, kit

(includes Parts 6a-6c)

-----

DATATRAK module

(see pages 11 and 12 for battery and

fuse replacement information)

24B767 Husky 1050 Aluminum

-----

CABLE

BRACKET, wall

24B774 Husky 1050 Polypropylene

24B776 Husky 1050 Conductive

Polypropylene

SOLENOID/REED SWITCH, kit

(includes Parts 4a-4d)

24K856 Husky 3300 Aluminum

24B771 Husky 1050 plastic air valve

24B772 Husky 1050 aluminum air valve

24K863 Husky 3300 plastic air valve

24K864 Husky 3300 aluminum air valve

24K858 Husky 3300 Polypropylene

6a -----

6b -----

6c -----

VALVE, air, smart

GASKET, air valve

FASTENERS, air valve

M6 x 25 screw, Aluminum air valve

M6 hex nut, Plastic air valve

7▲ 15V262 LABEL, warning (not shown)

4a -----

4b -----

REED SWITCH with SOLENOID

SCREW, reed switch

8-32 x 1.50 taptite, aluminum air

valve

8▲ 16A098 CARD, reference, language (not

6-19 x 1-5/8 plastite, plastic air valve

shown)

4c -----

4d -----

BRACKET, solenoid

FASTENER, solenoid

M6 x 25 screw, aluminum air valve

M6 hex nut, plastic air valve

▲ Replacement Warning labels, signs, tags, and cards

are available at no cost.

----- Not sold separately.

313840G

Download from Www.Somanuals.com. All Manuals Search And Download.

Parts

Conversion Kits, Cycle Count Only

Husky 1050 and Husky 3300 - 24B794 (Aluminum) and 24B795 (Polypropylene and Conductive

Polypropylene)

ti14224a

Ref.

No. Part No. Description

Qty

-----

DATATRAK module

(see pages 11 and 12 for battery

and fuse replacement information)

-----

CABLE, CAN

BRACKET, wall

REED SWITCH, kit

(includes Parts 5a-5b)

24B796 Plastic air valve

24B798 Aluminum air valve

-----

REED SWITCH

SCREW, reed switch

8-32 x 1.50 taptite, aluminum air

valve

6-19 x 1-5/8 plastite, plastic air

valve

6▲

7▲

15V262 LABEL, warning (not shown)

16A098 CARD, reference, language (not

shown)

▲ Replacement Warning labels, signs, tags, and cards

are available at no cost.

313840G

Download from Www.Somanuals.com. All Manuals Search And Download.

Parts

Replacement Kits

Solenoid/Reed Switch

Husky Husky

1050

3300

Air Valve Material

Includes

Plastic

Reed switch and solenoid (4a),

bracket (4c), and fasteners (4b, 4d)

24B771 24K863

24B772 24K864

Aluminum

Reed Switch

Husky

1050 or

Husky

3300

Air Valve Material

Includes

Plastic

24B796

24B798

Reed switch (5a)

and fastener (5b)

Aluminum

313840G

Download from Www.Somanuals.com. All Manuals Search And Download.

Graco Standard Warranty

Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in

material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty

published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by

Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written

recommendations.

This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty

installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of

non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with

structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or

maintenance of structures, accessories, equipment or materials not supplied by Graco.

This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of

the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned

to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will

be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.

THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED

TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.

Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy

(including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or

consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.

GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT

MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to

the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these

warranties.

In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or

the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the

negligence of Graco, or otherwise.

FOR GRACO CANADA CUSTOMERS

The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into,

given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la

rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite

de ou en rapport, directement ou indirectement, avec les procédures concernées.

Graco Information

For the latest information about Graco products, visit www.graco.com.

For patent information, see www.graco.com/patents.

TO PLACE AN ORDER, contact your Graco distributor or call to identify the nearest distributor.

Phone: 612-623-6921 or Toll Free: 1-800-328-0211 Fax: 612-378-3505

All written and visual data contained in this document reflects the latest product information available at the time of publication.

Graco reserves the right to make changes at any time without notice.

Original instructions.This manual contains English. MM 313840

Graco Headquarters: Minneapolis

International Offices: Belgium, China, Japan, Korea

GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS MN 55440-1441 • USA

www.graco.com

Revision G, July 2014

Download from Www.Somanuals.com. All Manuals Search And Download.

Haier Refrigerator BC100GS User Manual
Hamilton Beach Air Cleaner 04255 User Manual
Harbor Freight Tools Grinder 52847 User Manual
Harbor Freight Tools Outdoor Cart 40129 User Manual
Harman Kardon DVD Player DVD22B User Manual
Hayter Mowers Lawn Mower Code 100C User Manual
Hearth and Home Technologies Indoor Fireplace ST TRC User Manual
Hotpoint Ice Maker ffaa52k 1 User Manual
IBM Network Card EtherLink XL User Manual
Impex Home Gym MWB 345 User Manual