Operation
Husky™ 2200 Air-Operated
Diaphragm Pump
3A2578B
EN
Polypropylene and PVDF pumps for fluid transfer applications, including high viscosity materials. For
professional use only.
Not for use in European explosive atmosphere locations.
Important Safety Instructions
Read all warnings and instructions in this manual and in your
Repair/Parts manual.
Save these instructions.
Maximum Working Pressure: 125 psi
(0.86 MPa, 8.6 bar)
PROVEN QUALITY. LEADING TECHNOLOGY.
Download from Www.Somanuals.com. All Manuals Search And Download.
Warnings
The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The
exclamation point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific
risks. When these symbols appear in the body of this manual or on warning labels, refer back to these
Warnings. Product-specific hazard symbols and warnings not covered in this section may appear throughout
the body of this manual where applicable.
WARNING
FIRE AND EXPLOSION HAZARD
Flammable fumes, such as solvent and paint fumes, in work area can ignite or explode. To help
prevent fire and explosion:
• Use equipment only in well ventilated area.
• Eliminate all ignition sources; such as pilot lights, cigarettes, portable electric lamps, and
plastic drop cloths (potential static arc).
• Keep work area free of debris, including solvent, rags and gasoline.
• Do not plug or unplug power cords, or turn power or light switches on or off when flammable
fumes are present.
• Ground all equipment in the work area. See Grounding instructions.
• Use only grounded hoses.
• Hold gun firmly to side of grounded pail when triggering into pail. Do not use pail liners unless
they are antistatic or conductive.
• Stop operation immediately if static sparking occurs or you feel a shock. Do not use
equipment until you identify and correct the problem.
• Keep a working fire extinguisher in the work area.
• Route exhaust away from all ignition sources. If diaphragm ruptures, fluid may be exhausted
with air.
Static charge may build up on plastic parts during cleaning and could discharge and ignite
flammable vapors. To help prevent fire and explosion:
• Clean plastic parts only in well ventilated area.
• Do not clean with a dry cloth.
• Do not operate electrostatic guns in equipment work area.
PRESSURIZED EQUIPMENT HAZARD
Fluid from the equipment, leaks, or ruptured components can splash in the eyes or on skin
and cause serious injury.
• Follow the Pressure Relief Procedure when you stop spraying/dispensing and before
cleaning, checking, or servicing equipment.
• Tighten all fluid connections before operating the equipment.
• Check hoses, tubes, and couplings daily. Replace worn or damaged parts immediately.
3A2578B
3
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
EQUIPMENT MISUSE HAZARD
Misuse can cause death or serious injury.
• Do not operate the unit when fatigued or under the influence of drugs or alcohol.
• Do not exceed the maximum working pressure or temperature rating of the lowest rated
system component. See Technical Data in all equipment manuals.
• Use fluids and solvents that are compatible with equipment wetted parts. See Technical Data
in all equipment manuals. Read fluid and solvent manufacturer’s warnings. For complete
information about your material, request MSDS from distributor or retailer.
• Do not leave the work area while equipment is energized or under pressure.
• Turn off all equipment and follow the Pressure Relief Procedure when equipment is not in use.
• Check equipment daily. Repair or replace worn or damaged parts immediately with genuine
manufacturer’s replacement parts only.
• Do not alter or modify equipment. Alterations or modifications may void agency approvals
and create safety hazards.
• Make sure all equipment is rated and approved for the environment in which you are using it.
• Use equipment only for its intended purpose. Call your distributor for information.
• Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.
• Do not kink or over bend hoses or use hoses to pull equipment.
• Keep children and animals away from work area.
• Comply with all applicable safety regulations.
THERMAL EXPANSION HAZARD
Fluids subjected to heat in confined spaces, including hoses, can create a rapid rise in pressure
due to the thermal expansion. Over-pressurization can result in equipment rupture and serious
injury.
• Open a valve to relieve the fluid expansion during heating.
• Replace hoses proactively at regular intervals based on your operating conditions.
PLASTIC PARTS CLEANING SOLVENT HAZARD
Many solvents can degrade plastic parts and cause them to fail, which could cause serious
injury or property damage.
• Use only compatible water-based solvents to clean plastic structural or pressure-containing
parts.
• See Technical Data in this and all other equipment instruction manuals. Read fluid and
solvent manufacturer’s MSDSs and recommendations.
4
3A2578B
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
TOXIC FLUID OR FUMES HAZARD
Toxic fluids or fumes can cause serious injury or death if splashed in the eyes or on skin,
inhaled, or swallowed.
• Read MSDSs to know the specific hazards of the fluids you are using.
• Route exhaust away from work area. If diaphragm ruptures, fluid may be exhausted into
the air.
• Store hazardous fluid in approved containers, and dispose of it according to applicable
guidelines.
BURN HAZARD
Equipment surfaces and fluid that’s heated can become very hot during operation. To avoid
severe burns:
• Do not touch hot fluid or equipment.
PERSONAL PROTECTIVE EQUIPMENT
Wear appropriate protective equipment when in the work area to help prevent serious injury,
including eye injury, hearing loss, inhalation of toxic fumes, and burns. This protective
equipment includes but is not limited to:
• Protective eyewear, and hearing protection.
• Respirators, protective clothing, and gloves as recommended by the fluid and solvent
manufacturer.
3A2578B
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Ordering Information
To Find Your Nearest Distributor
Distributor Note
1. To find part numbers for new pumps or kits, use
the Online Husky Selector Tool.
2. Click on Where to Buy and use the Distributor
Locator.
2. To find part numbers for replacement parts:
a. Use the 20–digit number from the ID plate on
the pump. If you only have the Graco 6–digit
part number, use the selector tool to find the
corresponding 20–digit number.
To Specify the Configuration of a New
Pump
Please call your distributor.
OR
b. Use the Configuration Number Matrix on the
next page to understand which parts are
described by each digit.
Use the Online Husky Selector Tool on the Process
c. Use the Repair/Parts Manual 3A2714. Refer
to the main Parts illustration and to the
Parts/Kits Quick Reference. Follow the page
references on these two pages for further
ordering information, as needed.
To Order Replacement Parts
Please call your distributor.
3. Please call Graco Customer Service to order.
Related Manuals
Manual
Number
Title
3A2714
Husky 2200 Air-Operated Diaphragm
Pump, Repair/Parts
6
3A2578B
Download from Www.Somanuals.com. All Manuals Search And Download.
Configuration Number Matrix
Check the identification plate (ID) for the Configuration Number of your pump. Use the following matrix to
define the components of your pump.
PART NO.
CONFIGURATION NO.
SERIAL NO.
DATE CODE SERIES MAX WPR PSI-bar
MADE IN
Graco Inc., P.O. Box 1441
Mpls, MN 55440 USA
Sample Configuration Number: 2200P-P01AP1PPPTFKPT
PP PT FK
PT
2200P P01A
P1
Pump Model Center Section and Air Fluid Covers and
Valve Manifolds
Seats Balls Diaphragms
Manifold and Seat
Seals
Pump
Center Section and Air
Valve Material
For Use With
Fluid Covers and Manifolds
Polypropylene Standard
Polypropylene, Center Flange,
2200P
P01A
P1
P2
F2
Diaphragms
ANSI/DIN
Polypropylene
Polypropylene Overmolded
Diaphragms
Polypropylene, End Flange,
ANSI/DIN
PVDF, End Flange, ANSI/DIN
2200F
P01G
PVDF
Seat Material
Ball Material
Diaphragm Material
Manifold and Seat
Seal Material
Polypropylene
PVDF
Santoprene
Stainless Steel
FKM
PTFE
Santoprene
FKM
PTFE/EPDM Overmolded
PTFE/Santoprene 2–Piece
Santoprene
PTFE
PP
PV
SP
SS
FK
PT
SP
FK
PO
PT
SP
PT
3A2578B
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
General Information
c. Increase the size of the suction piping.
NOTE: Be sure the inlet fluid pressure does not
exceed 25 % of the outlet working pressure.
The Typical Installation shown is only a guide for
selecting and installing system components. Contact
your Graco distributor for assistance in planning a
system to suit your needs. Always use Genuine
Graco Parts and accessories. Be sure all accessories
are adequately sized and pressure rated to meet the
system’s requirements.
3. Reduce liquid velocity: Slow the cyclic rate of
the pump.
Pumped liquid viscosity is also very important but
normally is controlled by factors that are process
dependent and cannot be changed to reduce
cavitation. Viscous liquids are more difficult to pump
and more prone to cavitation.
Reference letters in the text, for example (A), refer to
the callouts in the figures.
Graco recommends taking all the above factors
into account in system design. To maintain pump
efficiency, supply only enough air pressure to the
pump to achieve the required flow.
Variations in color between the plastic components
of this pump are normal. Color variation does not
affect the performance of the pump.
Tighten Fasteners
Graco distributors can supply site specific
suggestions to improve pump performance and
reduce operating costs.
Before mounting and using the pump for the first time,
check and retorque all external fasteners. Follow
Torque Instructions, page 16, or see the torque
tag on your pump. After the first day of operation,
retorque the fasteners.
Mount The Pump
Tips to Reduce Cavitation
Cavitation in an AODD pump is the formation and
collapse of bubbles in the pumped liquid. Frequent
or excessive cavitation can cause serious damage,
including pitting and early wear of fluid chambers,
balls, and seats. It may result in reduced efficiency of
the pump. Cavitation damage and reduced efficiency
both result in increased operating costs.
To avoid serious injury or death from toxic fluid or
fumes:
• Ventilate to a remote area. The pump
exhaust air may contain contaminants. See
• Never move or lift a pump under pressure. If
dropped, the fluid section may rupture. Always
before moving or lifting the pump.
Cavitation depends on the vapor pressure of the
pumped liquid, the system suction pressure, and the
velocity pressure. It can be reduced by changing any
of these factors.
1. Be sure the mounting surface can support the
weight of the pump, hoses, and accessories, as
well as the stress caused during operation.
1. Reduce vapor pressure: Decrease the
temperature of the pumped liquid.
2. Increase suction pressure:
2. For all mountings, be sure the pump is secured
with screws through the mounting feet.
a. Lower the installed position of the pump
relative to the liquid level in the supply.
3. Make sure the surface is flat and that the pump
doesn’t wobble.
b. Reduce the friction length of the suction
piping. Remember that fittings add friction
length to the piping. Reduce the number of
fittings to reduce the friction length.
4. For ease of operation and service, mount the
pump so air valve, air inlet, fluid inlet and fluid
outlet ports are easily accessible.
8
3A2578B
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessories/Components Not Supplied
System Components
A
B
Air supply line
J
K
Air inlet port (not visible)
Air exhaust port and muffler
Bleed-type master air valve (may be
required for your pump)
Air filter/regulator assembly
Master air valve (to isolate the
filter/regulator for service)
Grounded flexible fluid supply line
Fluid drain valve (may be required for
your pump)
Fluid shutoff valve
C
D
L
M
Fluid inlet port
Fluid outlet port
E
F
N
Mounting feet
G
H
Grounded, flexible fluid outlet line
3A2578B
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Air Lines
Ground The System
1. Install an air regulator and gauge (C) to control
the fluid pressure. The fluid stall pressure will be
the same as the setting of the air regulator.
The equipment must be grounded to reduce the
risk of static sparking. Static sparking can cause
fumes to ignite or explode. Grounding provides an
escape wire for the electrical current.
2. Locate a bleed-type master air valve (B) close to
the pump and use it to relieve trapped air. Be
sure the valve is easily accessible from the pump
and located downstream from the regulator.
• Always ground the entire fluid system as
described below.
• Polypropylene and PVDF pumps are not
conductive and are not for use with flammable
fluids.
Trapped air can cause the pump to cycle
unexpectedly, which could result in serious
injury from splashing.
• Follow your local fire codes.
Before operating the pump, ground the system as
explained below.
3. Locate another master air valve (D) upstream
from all air line accessories and use it to isolate
them during cleaning and repair.
• Pump: Always ground the entire fluid system by
making sure the fluid has an electrical path to a
true earth ground.
4. An air line filter (C) removes harmful dirt and
moisture from the compressed air supply.
• Air and fluid hoses: Use only grounded hoses
with a maximum of 500 ft (150 m) combined hose
length to ensure grounding continuity.
5. Install a grounded, flexible air hose (A) between
the accessories and the 3/4 npt(f) pump air inlet.
• Air compressor: Follow manufacturer’s
recommendations.
• Fluid supply container: Follow local code.
• Solvent pails used when flushing: Follow local
code. Use only conductive metal pails, placed
on a grounded surface. Do not place the pail
on a nonconductive surface, such as paper or
cardboard, which interrupts grounding continuity.
Check your system electrical continuity after the
initial installation, and then set up a regular schedule
for checking continuity to be sure proper grounding
is maintained.
10
3A2578B
Download from Www.Somanuals.com. All Manuals Search And Download.
Air Exhaust Ventilation
To provide a remote exhaust:
1. Remove the muffler (U) from the pump air
exhaust port (K).
If pumping toxic fluids, you must vent the exhaust
away from people, animals, food handling areas,
and all sources of ignition. Follow all applicable
codes.
2. Install a grounded air exhaust hose (S) and
connect the muffler to the other end of the hose.
The minimum size for the air exhaust hose is 1
in. (26 mm) ID. If a hose longer than 15 ft (4.57
m) is required, use a larger diameter hose. Avoid
sharp bends or kinks in the hose.
NOTICE
3. Place a container (T) at the end of the air exhaust
line to catch fluid in case a diaphragm ruptures.
If the diaphragm ruptures, the fluid being pumped
will exhaust with the air.
The air exhaust port is 1 in. npt(f). Do not restrict
the air exhaust port. Excessive exhaust restriction
can cause erratic pump operation.
A
B
Air supply line
K
S
Air exhaust port
Bleed-type master air valve (may be
required for your pump installation)
Grounded air exhaust hose
C
D
J
Air filter/regulator assembly
Master air valve (for accessories)
Air inlet port (not visible)
T
Container for remote air exhaust
Muffler
U
3A2578B
11
Download from Www.Somanuals.com. All Manuals Search And Download.
3. For maximum suction lift (wet and dry), see
Technical Data, page 22. For best results, always
install the pump as close as possible to the
material source. Minimize suction requirements
to maximize pump performance.
Fluid Supply Line
1. Use grounded, flexible fluid hoses (E). See
2. If the inlet fluid pressure to the pump is more
than 25% of the outlet working pressure, the
ball check valves will not close fast enough,
resulting in inefficient pump operation. Excessive
inlet fluid pressure also will shorten diaphragm
life. Approximately 3–5 psi (0.02–0.03 MPa,
0.21–0.34 bar) should be adequate for most
materials.
Fluid Outlet Line
1. Use grounded, flexible fluid hoses. See
2. Install a fluid drain valve (F) near the fluid outlet.
3. Install a shutoff valve (G) in the fluid outlet line.
12
3A2578B
Download from Www.Somanuals.com. All Manuals Search And Download.
Flange Connections
The fluid inlet and outlet ports are 2 in. (50 mm)
raised face, ANSI/DIN PN 10 flanges. Connect 2 in.
(50 mm) plastic pipe flange to the pump as follows.
You will need:
• Torque wrench
• Adjustable wrench
• 6 in. (152 mm) diameter, 1/8 in (32 mm) thick
PTFE gasket, with four 0.75 in (19 mm). diameter
holes on a 4.75 in. (121 mmm) diameter bolt circle,
and a 2 in. (50 mm) diameter center
• Four 5/8 in (17 mm) x 3 in (76 mm) long bolts
• Four 5/8 in.(17 mm) spring lock washers
• Eight 5/8 in. (17 mm) flat washers
• Four 5/8 in. (17 mm) nuts
Figure 1
D
E
F
G
H
J
2 in. (50 mm) fluid inlet flange
2 in. (50 mm) fluid outlet flange
Plastic pipe flange
PTFE gasket
Bolt
Lock washer
Flat washer
1. Place a flat washer (K) on each bolt (H).
2. Align the holes in the gasket (G) and the pipe
flange (F) with the holes in the pump outlet flange
(E).
3. Lubricate the threads of the four bolts. Install
the bolts through the holes and secure with the
washers (K), lock washers (J), and nuts (L).
K
L
Nut
4. Hold the nuts with a wrench. Refer to the
tightening sequence in the figure and torque
the bolts to 20 to 30 ft-lb (27 to 41 Nm). Do not
overtorque.
Lubricate threads. torque to 20 to 30 ft-lb
(27 to 41 Nm). Do not overtorque.
5. Repeat for the pump inlet flange.
3A2578B
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Pressure Relief Procedure
3. Place the suction tube (if used) in fluid to be
pumped.
Follow the Pressure Relief Procedure
whenever you see this symbol.
NOTE: If fluid inlet pressure to the pump is more
than 25% of outlet working pressure, the ball
check valves will not close fast enough, resulting
in inefficient pump operation.
NOTICE
This equipment stays pressurized until pressure
is relieved manually. To help prevent serious
injury from pressurized fluid, such as splashing
in the eyes or on skin, follow the Pressure Relief
Procedure when you stop pumping and before you
clean, check, or service the equipment.
Excessive fluid inlet pressure can reduce
diaphragm life.
4. Place the end of the fluid hose into an appropriate
container.
5. Close the fluid drain valve.
1. Shut off the air supply to the pump.
2. Open the dispensing valve, if used.
6. Turn the air regulator knob to 0. Open all
bleed-type master air valves.
3. Open the fluid drain valve to relieve fluid
pressure. Have a container ready to catch the
drainage.
7. If the fluid hose has a dispensing device, hold
it open.
8. Slowly increase air pressure with the air regulator
until the pump just starts to cycle. Allow the
pump to cycle slowly until all air is pushed out of
the lines and the pump is primed.
Tighten Fasteners
Before mounting and using the pump for the first time,
check and retorque all external fasteners. Follow
Torque Instructions, page 16, or see the torque
tag on your pump. After the first day of operation,
retorque the fasteners.
NOTE: Use lowest possible air pressure to prime,
just enough to cycle the pump. If the pump does
not prime as expected, turn air pressure DOWN.
9. If you are flushing, run the pump long enough to
thoroughly clean the pump and hoses.
Flush the Pump Before First Use
The pump was tested in water. If water could
contaminate the fluid you are pumping, flush the
pump thoroughly with a compatible solvent. See
10. Close the bleed-type master air valve.
Pump Shutdown
Start and Adjust the Pump
1. Be sure the pump is properly grounded. See
2. Check fittings to be sure they are tight. Use a
compatible liquid thread sealant on male threads.
Tighten fluid inlet and outlet fittings securely
At the end of the work shift and before you check,
adjust, clean, or repair the system, follow the
14
3A2578B
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Maintenance Schedule
Flushing and Storage
Establish a preventive maintenance schedule
based on the pump’s service history. Scheduled
maintenance is especially important to prevent spills
or leakage due to diaphragm failure.
Lubrication
• Flush before fluid can dry in the equipment, at the
end of the day, before storing, and before repairing
equipment.
The pump is lubricated at the factory. It is designed
to require no further lubrication for the life of the
packings. There is no need to add an inline lubricator
under normal operating conditions.
• Flush at the lowest pressure possible. Check
connectors for leaks and tighten as necessary.
• Use solvent that is compatible with the equipment
wetted parts and the material being dispensed.
Tighten Threaded Connections
• Always flush the pump and relieve the pressure
before storing it for any length of time.
Before each use, check all hoses for wear or damage
and replace as necessary. Check to be sure all
threaded connections are tight and leak-free. Check
mounting bolts. Check fasteners. Tighten or retorque
as necessary. Although pump use varies, a general
guideline is to retorque fasteners every two months.
NOTICE
Flush the pump often enough to prevent the fluid
you are pumping from drying or freezing in the
pump and damaging it.
3A2578B
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Torque Instructions
If fluid cover or manifold fasteners have been
loosened, it is important to torque them using the
following procedure to improve sealing.
Inlet and Outlet Manifold Screws
NOTE: Fluid cover and manifold fasteners have a
thread-locking adhesive patch applied to the threads.
If this patch is excessively worn, the fasteners may
loosen during operation. Replace screws with new
ones or apply medium-strength (blue) Loctite or
equivalent to the threads.
NOTE: Always completely torque fluid covers before
torquing manifolds.
1. Start all fluid cover screws a few turns. Then, turn
down each screw just until head contacts cover.
2. Turn each screw by 1/2 turn or less working in a
crisscross pattern to specified torque.
Air Valve Screws and Pilot Valves
3. Repeat for manifolds.
Fluid cover and manifold fasteners: 190 to 220
in-lb (21 to 25 Nm)
4. Retorque the air valve fasteners in a crisscross
pattern to the specified torque.
Air valve fasteners: 45 to 55 in-lb (5 to 6 Nm)
5. Retorque the pilot valves to the specified torque.
Do not overtorque.
Pilot valves: 20 to 25 in-lb (2 to 3 Nm)
Fluid Cover Screws
16
3A2578B
Download from Www.Somanuals.com. All Manuals Search And Download.
Dimensions
End Flange Models, Polypropylene
and PVDF
Polypropylene
PVDF
Polypropylene
19.8 in. 50.3 cm 19.8 in. 50.3 cm
7.0 in. 17.8 cm 7.0 in. 17.8 cm
13.9 in. 35.3 cm 13.9 in. 35.3 cm
16.3 in. 41.4 cm 16.3 in. 41.4 cm
PVDF
A
B
C
D
E
F
25.1 in. 63.8 cm 25.2 in. 64.0 cm
28.7 in. 72.9 cm 28.8 in. 73.2 cm
31.7 in. 80.5 cm 31.8 in. 80.8 cm
G
H
J
K
L
3.6 in.
9.1 cm
3.6 in.
9.1 cm
12.0 in. 30.5 cm 11.7 in. 29.7 cm
25.6 in. 65.0 cm 25.3 in. 64.3 cm
8.2 in.
20.8 cm
8.2 in.
20.8 cm
18
3A2578B
Download from Www.Somanuals.com. All Manuals Search And Download.
Center Flange Models, Polypropylene
Only
Polypropylene
Polypropylene
A
B
C
D
E
F
24.1 in.
27.2 in.
30.3 in.
3.1 in.
12.8 in.
26.3 in.
61.2 cm
69.1 cm
77.0 cm
7.9 cm
32.5 cm
66.8 cm
G
H
J
K
L
18.5 in.
7.0 in.
13.9 in.
16.3 in.
8.2 in.
47.0 cm
17.8 cm
35.3 cm
41.4 cm
20.8 cm
3A2578B
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Performance Charts
Bolt-through Diaphragms
Fluid Pressure
Approximate Cycles per Minute
25
50
75
100
125
125
(0.86, 8.6)
A
B
100
(0.70, 7.0)
75
Operating Air Pressure
A
125 psi (0.86 MPa, 8.6 bar)
(0.52, 5.2)
PSI
(MPa, bar)
C
D
50
(0.34, 3.4)
B
100 psi (0.7 MPa, 7.0 bar)
25
(0.17, 1.7)
C
70 psi (0.48 MPa, 4.8 bar)
0
0
40
(151)
80
(303)
120
(454)
160
(606)
200
(757)
D
40 psi (0.28 MPa, 2.8 bar)
Fluid Flow — gpm (lpm)
How to Read the Charts
Air Consumption
1. Locate fluid flow rate along
bottom of chart.
Approximate Cycles per Minute
25
50
75
100
125
175
(5.0)
2. Follow vertical line up to
intersection with selected
operating air pressure
curve.
140
(4.0)
A
B
3. Follow left to scale to read
fluid outlet pressure (top
chart) or air consumption
(bottom chart)
105
(3.0)
scfm
(Nm3/min.)
C
D
70
(2.0)
35
(1.0)
0
0
40
80
120
160
200
(151)
(303)
(454)
(606)
(757)
Fluid Flow — gpm (lpm)
20
3A2578B
Download from Www.Somanuals.com. All Manuals Search And Download.
Overmolded Diaphragms
Fluid Pressure
Approximate Cycles per Minute
31
62
93
124
155
125
(0.86, 8.6)
A
B
100
(0.70, 7.0)
75
Operating Air Pressure
(0.52, 5.2)
PSI
(MPa, bar)
A
C
D
125 psi (0.86 MPa, 8.6 bar)
50
(0.34, 3.4)
B
100 psi (0.7 MPa, 7.0 bar)
25
(0.17, 1.7)
C
70 psi (0.48 MPa, 4.8 bar)
0
0
40
(151)
80
(303)
120
(454)
160
(606)
200
(757)
D
40 psi (0.28 MPa, 2.8 bar)
Fluid Flow — gpm (lpm)
How to Read the Charts
Air Consumption
1. Locate fluid flow rate along
bottom of chart.
Approximate Cycles per Minute
31
62
93
124
155
175
(5.0)
2. Follow vertical line up to
intersection with selected
operating air pressure
curve.
A
B
140
(4.0)
3. Follow left to scale to read
fluid outlet pressure (top
chart) or air consumption
(bottom chart)
105
(3.0)
scfm
(Nm3/min.)
C
D
70
(2.0)
35
(1.0)
0
0
40
80
120
160
200
(151)
(303)
(454)
(606)
(757)
Fluid Flow — gpm (lpm)
3A2578B
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Data
Husky 2200 Diaphragm Pump
US
Metric
Maximum fluid working pressure
Air pressure operating range
Air inlet size
125 psi
20 to 125 psi
0.86 MPa, 8.6 bar
0.14 to 0.86 MPa, 1.4 to 8.6 bar
3/4 in. npt(f)
1 in. npt(f)
Air exhaust size
Fluid inlet and outlet size (ANSI/DIN
flange)
2 in
50 mm
Maximum suction lift (reduced
if balls don’t seat well due to
damaged balls or seats, lightweight
balls, or extreme speed of cycling)
Maximum size pumpable solids
Minimum ambient air temperature
for operation and storage.
Wet: 31 ft
Dry: 16 ft
Wet: 9.4 m
Dry: 4.9 m
1/4 in.
32° F
6.3 mm
0° C
NOTE: Exposure to extreme low
temperatures may result in damage
to plastic parts.
Air consumption
Standard diaphragms
70 scfm at 70 psi; 100 gpm
75 scfm at 70 psi, 100 gpm
2.0 m3/min at 0.48 MPa, 4.8
bar, 379 lpm
2.1 m3/min at 0.48 MPa, 4.8
bar, 379 lpm
Overmolded diaphragms
Maximum air consumption
Standard diaphragms
Overmolded diaphragms
Noise (dBa)
140 scfm
157 scfm
4.0 m3/min
4.4 m3/min
Sound power measured per ISO-9614–2. Sound pressure was tested 3.28 ft (1 m) from equipment.
Sound Power
95.2 at 70 psi and 50 cpm
101.8 at 100 psi and full flow
87.3 at 70 psi and 50 cpm
94.7 at 100 psi and full flow
95.2 at 4.8 bar and 50 cpm
101.8 at 7.0 bar and full flow
87.3 at 4.8 bar and 50 cpm
94.7 at 7.0 bar and full flow
Sound Pressure
Fluid flow per cycle
Standard diaphragms
Overmolded diaphragms
Maximum free-flow delivery
Standard diaphragms
Overmolded diaphragms
1.6 gallons
1.3 gallons
6.1 liters
4.9 liters
200 gpm
200 gpm
757 lpm
757 lpm
22
3A2578B
Download from Www.Somanuals.com. All Manuals Search And Download.
Maximum pump speed
Standard diaphragms
Overmolded diaphragms
Weight
125 cycles per minute
155 cycles per minute
Polypropylene
PVDF
80 lb
106 lb
36.3 kg
48.1 kg
Wetted Parts
Wetted parts include material(s) chosen for seat, ball, and diaphragm options, plus the pump’s material of
construction: Polypropylene or PVDF
Non-wetted external parts
stainless steel, polypropylene
Fluid Temperature Range
Diaphragm/Ball/Seat Material
US
Metric
Polypropylene
Pump
PVDF Pump
Polypropylene
PVDF Pump
Pump
FKM Fluoroelastomer
Polypropylene
32° to 150°
32° to 150°
40° to 150°
40° to 150°
32° to 150°
32° to 150°
40° to 150°
32° to 225°
32° to 150°
40° to 180°
40° to 220°
32° to 225°
32° to 180°
40° to 180°
0° to 66°
0° to 66°
4° to 66°
4° to 66°
0° to 66°
0° to 66°
4° to 66°
0° to 107°
0° to 66°
4° to 82°
4° to 104°
0° to 107°
0° to 82°
4° to 82°
PTFE overmolded diaphragm
PTFE check balls
PVDF
Santoprene
2–piece PTFE/Santoprene
diaphragm
3A2578B
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Graco Standard Husky Pump Warranty
Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its
name to be free from defects in material and workmanship on the date of sale to the original purchaser for
use. With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a
period of five years from the date of sale, repair or replace any part of the equipment determined by Graco
to be defective. This warranty applies only when the equipment is installed, operated and maintained in
accordance with Graco’s written recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction,
damage or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper
maintenance, negligence, accident, tampering, or substitution of non-Graco component parts. Nor shall
Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment
with structures, accessories, equipment or materials not supplied by Graco, or the improper design,
manufacture, installation, operation or maintenance of structures, accessories, equipment or materials
not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an
authorized Graco distributor for verification of the claimed defect. If the claimed defect is verified, Graco
will repair or replace free of charge any defective parts. The equipment will be returned to the original
purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material
or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of
parts, labor, and transportation.
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR
IMPLIED, INCLUDING BUT NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY
OF FITNESS FOR A PARTICULAR PURPOSE.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above.
The buyer agrees that no other remedy (including, but not limited to, incidental or consequential damages
for lost profits, lost sales, injury to person or property, or any other incidental or consequential loss) shall
be available. Any action for breach of warranty must be brought within six (6) years of the date of sale..
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IN CONNECTION WITH
ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT MANUFACTURED BY
GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.),
are subject to the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable
assistance in making any claim for breach of these warranties..
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from
Graco supplying equipment hereunder, or the furnishing, performance, or use of any products or other
goods sold hereto, whether due to a breach of contract, breach of warranty, the negligence of Graco, or
otherwise.
FOR GRACO CANADA CUSTOMERS
The Parties acknowledge that they have required that the present document, as well as all documents,
notices and legal proceedings entered into, given or instituted pursuant hereto or relating directly or
indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la rédaction du
présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés,
donnés ou intentés, à la suite de ou en rapport, directement ou indirectement, avec les procédures
concernées.
Graco Information
To place an order, contact your Graco Distributor or call to identify the nearest distributor.
Phone: 612-623-6921 or Toll Free: 1-800-328-0211 Fax: 612-378-3505
All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
Original Instructions. This manual contains English. MM 3A2578
Graco Headquarters: Minneapolis
International Offices: Belgium, China, Japan, Korea
GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS MN 55440-1441 • USA
Copyright 2014, Graco Inc. All Graco manufacturing locations are registered to ISO 9001.
Revision B, June 2014
Download from Www.Somanuals.com. All Manuals Search And Download.
|