Instructions - Parts List
311304J
GTP10 Pump
EN
For pumping gasoline, diesel fuel, and kerosene. Do not use to pump other fluids including
water.
Models 260000 through 260017, 260019, 260024, 260580, and 260581
10 gpm (38 lpm), 12 VDC (CSA C/US listed motor)
Models 260020 and 260021, 10 gpm (38 lpm), 24 VDC
Models 260022 and 260023, 12 gpm (45 lpm), 230 VAC
Models 260025 through 260028
12 gpm (45 lpm), 115 VAC (CSA C/US listed motor)
10 psi (0.07 MPa, 0.7 bar) Maximum Working Pressure
Important Safety Instructions
Read all warnings and instructions in this
manual. Save these instructions.
CSA mark applies only to 12 VDC
and 115 VAC motors for Class I, Div
I, Group D Hazardous Locations
Download from Www.Somanuals.com. All Manuals Search And Download.
Models
311304J
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Warnings
Warnings
The following general warnings are for the setup, use, grounding, maintenance, and repair of this equipment. Addi-
tional, more specific warnings may be found throughout the body of this manual where applicable. Symbols appear-
ing in the body of the manual refer to these general warnings. When these symbols appear throughout the manual,
refer back to these pages for a description of the specific hazard.
WARNING
FIRE AND EXPLOSION HAZARD
When flammable fluids are present in the work area, such as gasoline and windshield wiper fluid, be
aware that flammable fumes can ignite or explode. To help prevent fire and explosion:
•
•
•
•
•
•
•
Use equipment only in well ventilated area.
Eliminate all ignition sources, such as cigarettes and portable electric lamps.
Keep work area free of debris, including rags and spilled or open containers of solvent and gasoline.
Do not plug or unplug power cords or turn lights on or off when flammable fumes are present.
Ground all equipment in the work area.
Use only grounded hoses.
If there is static sparking or you feel a shock, stop operation immediately. Do not use equipment
until you identify and correct the problem.
•
Keep a fire extinguisher in the work area.
ELECTRIC SHOCK HAZARD
Improper grounding, setup, or usage of the system can cause electric shock.
•
Turn off and disconnect power at main switch before disconnecting any cables and before servicing
equipment.
•
•
Connect only to grounded power source.
All electrical wiring must be done by a qualified electrician and comply with all local codes and
regulations.
PERSONAL PROTECTIVE EQUIPMENT
You must wear appropriate protective equipment when operating, servicing, or when in the operating
area of the equipment to help protect you from serious injury, including eye injury, inhalation of toxic
fumes, burns, and hearing loss. This equipment includes but is not limited to:
•
•
•
•
Protective eyewear
Clothing and respirator as recommended by the fluid and solvent manufacturer
Gloves
Hearing protection
PRESSURIZED EQUIPMENT HAZARD
Fluid from the gun/dispense valve, leaks, or ruptured components can splash in the eyes or on skin and
cause serious injury.
•
Follow Pressure Relief Procedure in this manual, when you stop dispensing and before cleaning,
checking, or servicing equipment.
•
•
Tighten all fluid connections before operating the equipment.
Check hoses, tubes, and couplings daily. Replace worn or damaged parts immediately.
4
311304J
Download from Www.Somanuals.com. All Manuals Search And Download.
Warnings
WARNING
EQUIPMENT MISUSE HAZARD
Misuse can cause death or serious injury.
•
•
Do not operate the unit when fatigued or under the influence of drugs or alcohol.
Do not exceed the maximum working pressure or temperature rating of the lowest rated system
component. See Technical Data in all equipment manuals.
•
•
Use fluids and solvents that are compatible with equipment wetted parts. See Technical Data in all
equipment manuals. Read fluid and solvent manufacturer’s warnings. For complete information
about your material, request MSDS forms from distributor or retailer.
Check equipment daily. Repair or replace worn or damaged parts immediately with genuine Graco
replacement parts only.
•
•
•
•
•
•
Do not alter or modify equipment.
Use equipment only for its intended purpose. Call your Graco distributor for information.
Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.
Do not kink or over bend hoses or use hoses to pull equipment.
Keep children and animals away from work area.
Comply with all applicable safety regulations.
BURN HAZARD
Equipment surfaces and fluid that’s heated can become very hot during operation. To avoid severe
burns, do not touch hot fluid or equipment. Wait until equipment/fluid has cooled completely.
311304J
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Installation
When unpacking pump, check for shipping damage.
Report any shipping damage to delivering carrier imme-
diately.
CAUTION
Do not use a curb pump automatic shut-off nozzle
with this pump. Use of a curb pump automatic nozzle
may cause priming problems, reduced output flow,
and motor overheating. If an automatic shut-off nozzle
is required, use Graco part number 260082 (regular)
or 260083 (unleaded) or Catlow, Inc. part number
NCLF-1 (regular) or NCNLF-1 (unleaded).
FIG. 1
FIG. 2
FIG. 3
Mounting Pump
CAUTION
•
•
Ensure tank being used is clean and free of welding
slag
Ensure the tank is vented to allow air into the tank
as the fuel is being pumped out. Failure to provide a
vent will cause priming problems
1. Apply PTFE thread tape (provided with the pump) to
large thread of bung adapter (9) (2 in. X 1 ½ in.
reducer fitting). Install bung adapter to fuel tank.
2. Assemble suction tube sections by applying ¼ in. to
½ in. wide bead of PVC cement (PN: 260086; white
tube provided with the pump) around the entire
inside diameter of the coupler (see FIG. 1). While
sliding the tube into the couplers turn the tube at
least one full revolution until the tube bottoms out on
the coupler (see FIG. 2, FIG. 3, and FIG. 4). This will
allow the cement to coat the entire surface for the
best possible seal. Allow cement to set for 5 min-
utes minimum before installing pump into tank.
For tanks deeper than 36 in. (914 mm) you will
need a standard 1 in. (25 mm) pipe with 1 in. npt
threads on one end. Suction tubes longer than 60
in. (1.52 m) require a foot valve (Graco Part No.
260217) at the bottom of the tube to prevent loss of
prime.
FIG. 4
6
311304J
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
3. Cut the suction tube so that it is 2 in. (55 mm) from
the bottom of the tank when installed in the tank.
Mounting Hose and Nozzle
1. Apply thread tape provided with pump to both ends
of hose assembly. Screw ¾” NPT end of 90° union
swivel (15) to one end of hose (see fig. 5).
4. Insert gasket (7f) into union nut (1k). If using Graco
supplied PVC suction tube it is not necessary to
apply thread tape before assembly, just screw into
pump inlet (1j). If using metal suction tube (not sup-
plied with pump) then apply thread tape provided
with pump to NPT threads before assembling to
pump inlet (1j).
2. Screw nozzle onto other end of hose and tighten.
3. Start swivel end of 90° union swivel (15) onto ¾”
hose/nozzle assembly to desired position and
tighten swivel fitting.
5. Insert suction tube attached to pump through bung
adapter (9) into tank. Position pump as desired and
tighten union nut (1k) on bung adapter (9).
It is important that the swivel end of the 90° union
swivel (15) is assembled to the ¾” outlet nipple (14)
for proper sealing (see FIG. 6). If the pump has diffi-
culty priming, it is easy to remove the swivel and
pour fluid into the pump outlet cavity when assem-
bled this way.
FIG. 5
FIG. 6
311304J
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Electrical Installation
12 VDC and 24 VDC
Electrical Installation
115 VAC and 230 VAC
If you are installing models 260580 or 260581 skip
this section. These pumps have been factory wired
On 115 VAC and 230 VAC pumps, electrical con-
nections must be made by a licensed electrician per
requirements of local, state, and national codes
regarding class 1, group D installations. Only rigid
conduit with threaded connections or other
approved wiring methods for Class 1 or Division 1
installations should be used. Conduit opening in
pump must be sealed with waterproof, fuel-resistant
sealant. Failure to comply with this warning could
result in injury from electrical shock, fire or explo-
sion.
To install wiring for a negative ground system:
1. Ensure pump switch is OFF.
2. To remove electrical cover (2a), remove four bolts
(2c).
Power cable can be cut to shorter length if 18 feet
(5.5 m) is not required. Cut to proper length and
proceed with steps 3 and 4.
3. Strip 3 in. (76 mm) of outside insulation from power
cable (6c) from end opposite of fuse.
1. Ensure pump switch is OFF and electrical power is
disconnected.
4. Strip 3/8 in. (10 mm) of insulation from red and black
wires.
2. Install conduit and user-supplied power cord to
pump.
5. Slide strain relief (6b) over end of power cable (6c)
on the end just stripped. Male thread of strain relief
should be toward stripped end.
3. Strip 3 in. (76 mm) from power cord jacket and 1/2
in. (13 mm) from individual conductor insulation.
4. To remove electrical cover (2a), remove four bolts
(2c).
6. Insert power cable through conduit thread in electri-
cal cover (2a). Connect wires from power cable to
wires from the motor using wire nuts (2e): red to red
and black to black.
5. Remove 1/2 in. (13 mm) of insulation from power
wires inside pump electrical terminal cavity.
6. Insert electrical power wire through conduit opening
in back of pump.
7. Screw strain relief (6b) into electrical cover (2a).
8. Position power cable (6c) so the large diameter of
power cable extends through strain relief (6b).
7. Using wire nuts (2e), connect wires: green to green,
white to white, and black to black.
9. Tighten nut on strain relief to form a seal around the
power cable.
8. Replace electrical cover.
10. Reinstall electrical cover (2a) on the pump.
11. Remove 1/2 in. (13 mm) of insulation from wires on
the fuse holder end of the power cable.
12. Attach battery clamps (6a) with red sleeve to red
wire and black sleeve to black wire. Wire must be
crimped to the battery clamp firmly to get a good
electrical connection.
13. Connect red wire with fuse holder inline to positive
battery terminal. Connect black wire to negative bat-
tery terminal.
8
311304J
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Priming Pump
Operation
All pump models should prime within 5 seconds after
pump is turned on up to a height of 36 in. (91 mm).
Pumps installed at height up to 5 ft. (1.52 m) may have
difficulty priming. Follow procedure below to initiate
prime. Pumps installed at suction height above 5 ft.
(1.52 m) will have difficulty in holding prime. It is recom-
mended that check valve (Graco part no. 260217) be
added to the bottom of the suction tube to help maintain
prime.
Before servicing, turn pump off and open the
nozzle to relieve pressure.
CAUTION
Do not operate pump dry. Do not run pump for more
than 5 minutes with nozzle closed. Do not operate
pump for more than 30 minutes continuously in 1 hour.
If prime in not achieved in 30 seconds after turning the
pump on use the following procedure to initiate prime;
On/Off switch lever (8d) is located under nozzle holder.
Remove nozzle before turning pump on.
1. Remove 90° Union Swivel (15) from ¾” Inlet Nipple
(14).
1. Move switch lever (8d) on.
2. Pour fluid being pumped into pump outlet until com-
pletely filled.
2. Insert nozzle into tank and actuate nozzle lever to
dispense fuel.
3. Re-assemble Union Swivel (15) back onto nipple
(14). Turn pump on. The pump should gain prime in
under 5 seconds.
3. Immediately after fueling turn switch lever (8d) off.
4. If pump still does not gain prime check for any major
leaks in the system. If no leaks are found then the
pump is mechanically defective and should be
reported to Graco Product Service for disposition.
Maintenance
1. Clean inlet strainer (3b) after every 50 hours of
operation.
It is important that the swivel end of the 90° union
swivel (15) is assembled to the ¾” outlet nipple (14)
for proper sealing (see fig. 6). Also, if the pump has
difficulty priming it is easy to remove the swivel and
pour fluid into the pump outlet cavity when assem-
bled this way.
2. To remove inlet strainer (3b), remove four screws
(3c) and strainer cover (3a). Remove and clean
strainer.
3. If strainer is excessively dirty, clean tank to protect
pump and the equipment being fueled.
If prime is lost
4. After cleaning strainer, replace strainer and cover.
Make sure cover seal (3d/7e) is in place.
1. First make sure there are no fluid leaks from the
pump outlet out to the fuel nozzle. Any leaks after
the outlet will allow air to push the fluid column back
to the tank and prime will be lost.
2. If no leaks are detected on the outlet side of the
pump, remove the pump from the tank and inspect
the suction tube and pump inlet for leaks.
3. If the system is leak free and the suction height
guidelines are followed the pumping system should
not lose prime.
All guidelines and procedures are based on pump-
ing diesel fuel. If pumping gasoline priming may be
more difficult due to the lift of gasoline dependent
on Reid's vapor pressure of the gasoline and it's
temperature. The lower the vapor pressure and
temperature, the higher the possible lift.
311304J
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Troubleshooting
Problem
Cause
Solution
Motor runs but pump will not prime. Motor rotation wrong. (12 VDC and
24 VDC units only.)
Check wiring instructions for possible
problems.
Missing relief valve o-ring seal
(4c/7a).
Remove gear cover (1b) inspect seal
(4c/7a), replace if missing or
damaged.
Sheared drive key (1f/7c).
Remove cover (1b) and inspect key
(1f/7c/10b), replace if worn or
sheared.
Dirt under relief poppet (4a) or seal
(4c/7a).
Remove cover (1b) and inspect,
clean or replace if damaged.
Strainer seal (3d/7e) leaking.
Suction height too high to prime.
Worn or damaged gears.
Inspect and replace if damaged.
See Priming Pump, page 9.
Remove cover (1b) and inspect
gears. Replace if worn or damaged.
Fuel level low.
Refill tank.
Cover seal (1e7b/10c) damaged.
Inlet strainer (3b) clogged.
Air leak in suction tube.
Replace if worn or damaged.
Remove and clean or replace.
Inspect all joints in suction tube.
Make sure all joints in suction tube
are sealed. and that there are no
cracks from over-tightening
Air lock in system.
This may occur if filter or meter or
automatic shut-off nozzle is used. If
this occurs, fill pump and meter with
fuel through top of pump.
Motor does not run at proper speed. Check electric connections. Check
supply voltage for proper voltage
level.
Unit pumps but output flow is low.
Clogged inlet strainer (3b).
Air leak in suction tube.
Clean or replace.
Check to make sure all joints in suc-
tion tube are sealed and that there
are no cracks.
Suction tube too close to tank
bottom.
Suction tube must have a 2 in.
(51 mm) minimum clearance.
Tank empty.
Refill tank.
Tank not vented.
Worn or damaged gears.
Tank must be vented to atmosphere.
Remove cover (1b) and inspect
gears. Replace if worn or damaged.
Damaged motor.
Replace motor.
Clogged suction tube, hose, or
nozzle.
Inspect and clean.
10
311304J
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Problem
Cause
Solution
Motor stalls when nozzle is closed.
Bypass relief valve (4a) stuck.
Inspect relief valve, making sure
poppet is free. Replace if damaged.
Low supply voltage.
Check supply voltage.
Gears (1c/10a) damaged and
binding.
Inspect gears. Gears should turn
freely. Replace if damaged.
Faulty motor.
Replace motor.
Fuel leaking in motor mount.
Faulty or damaged motor shaft seal Replace shaft seal
(1g/7d).
Operating pump extended time with Do not exceed 5 minutes of operation
nozzle closed.
with nozzle closed.
Motor shaft worn.
Replace motor if shaft has groove
worn in seal area.
Motor overheating.
Gears (1c/10a) binding.
Check to make sure gears turn freely
on shaft.
Operating pump extended time with Do not exceed 5 minutes of operation
nozzle closed.
with nozzle closed.
Clogged inlet strainer (3b).
Clean or replace, see Maintenance,
Clogged suction tube, hose, or
nozzle.
Inspect and clean if required.
Operating pump more than 30 min-
utes continuous duty.
Limit operation to 30 minutes per
hour.
Switch will not turn pump on.
Blown fuse.
Replace fuse. 20 amp automotive
fuse (Littelfuse ATO 257020 or
Bussman ATC-20).
Electrical problem.
Check that supply voltage is proper
and getting to pump.
Defective switch (8e).
Mechanical problem.
Check and replace if defective.
Check switch actuator cam (8c). Cam
should be actuating the switch (8e).
Damaged or defective motor.
Check motor, replace if damaged or
defective.
311304J
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts Drawing
Parts Drawing
Models 260000 through 260017, 260019,
260024, 260580, and 260581, 12 VDC
Models 260020 and 260021, 24 VDC
Models 260022 and 260023, 230 VAC
Models 260025 through 260028, 115 VAC
3c
260456
3a
1h
3d/7e
3b
Packing Kit 260434 includes items 7a-7f
which are also included in other kits.
260458
260459
253723
1b
1e/7b/10c
1f/7c/10b
1c/ 10a
1d
1j
4c/
7a
9
4b
260457
4a
15
7f
1a
1k
1g/7d
2g
This end to
hose (11)
2h
2i
14
5c
5a
2c
2b
2d
2e
2f
260300
260450
260451
260452
260453
253719
253720
253721
253722
5b
5a
8e
8f
8b
8g
8c
260433
253718
2a
2c
6b
6a
8a
6c
260454
8d
12
311304J
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List
Parts List
Models 260000 through 260017, 260019, 260024, 260580, and 260581, 12 VDC
Models 260020 and 260021, 24 VDC
Models 260022 and 260023, 230 VAC
Models 260025 through 260028, 115 VAC
Qty
.
Qty
Ref. No.
Description
Ref. No.
1
Description
260458 KIT, pump with swivel, blue
(includes items 1a-1k)
.
3
260456 KIT, filter, universal
(includes items 3a-3d)
3a
3b
3c
3d (7e)
COVER, strainer
SCREEN
SCREW, hex head, 10-24 x 3/8 in.
SEAL, strainer cover
1
1
260459 KIT, pump without swivel, blue
(includes items 1a-1j)
253723 KIT, pump with swivel, black
(includes items 1a-1k)
1
1a
1b
BODY, assembly
COVER, gear
1
1
2
2
1
4
260457 KIT, popoff (includes items 4a-4c)
4a
POPPET, relief valve
SPRING, relief valve
SEAL, relief valve
1
1
1
1c (10a) GEAR
1d
1e
4b
SHAFT, gear
SEAL, gear cover
4c (7a)
(7b/10c)
1f
5* 260300 KIT, suction, pipe
(includes items 5a-5c)
KEY, drive
1
(7c/10b)
1g (7d)
1h
1j
1k
5a
5b
5c
5d
PIPE, PVC
2
1
1
1
SEAL, shaft
BOLT, hex, 5/16-18 x 3/4 in.
FITTING, inlet
1
4
1
1
COUPLER, PVC, female
ADAPTER, PVC, male
CEMENT, PVC (not shown)
NUT, union (260458 and 253723)
6** 260454 KIT, cable, 12 V and 24 V only
(includes items 6a-6c)
2
260450 KIT, motor, 12 VDC, blue
(includes items 2a-2i)
260451 KIT, motor, 24 VDC, blue
(includes items 2a-2i)
260452 KIT, motor, 115 VAC, blue
(includes items 2a-2i)
260453 KIT, motor, 230 VAC, blue
(includes items 2a-2i)
6a
CLAMP, battery
BLACK SLEEVE
RED SLEEVE
2
1
1
1
1
6b
6c
STRAIN RELIEF
ASSEMBLY, power cable,
18 ft (5.5 m), fuse holder, 20 amp
fuse
253719 KIT, motor, 12 VDC, black
(includes items 2a-2i)
253720 KIT, motor, 24 VDC, black
(includes items 2a-2i)
253721 KIT, motor, 115 VAC, black
(includes items 2a-2i)
7
260434 KIT, packing (includes items 7a-7f)
1
1
1
7a (4c)
7b
SEAL, relief valve
SEAL, gear cover
(1e/10c)
7c
KEY, drive
1
(1f/10b)
7d (1g)
7e (3d)
7f
253722 KIT, motor, 230 VAC, black
(includes items 2a-2i)
SEAL, shaft
SEAL, strainer cover
GASKET, inlet
1
1
1
2a
2b
2c
2d
2e
COVER, electrical
1
1
10
2
2
3
HOUSING, electrical, 12 V
BOLT, hex, 1/4-20 x 3/4 in.
NUT, 10-32
WIRE NUT, 260450 and 260451
WIRE NUT, 260452 and 260453
FLAG TERMINAL
2f
2
2g
2h
2i
MOTOR, electric
COVER, nozzle
GUIDE, nozzle
1
1
1
311304J
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List (continued)
Parts List (continued)
Models 260000 through 260017, 260019, and 260024, 12 VDC
Models 260020 and 260021, 24 VDC
Models 260022 and 260023, 230 VAC
Models 260025 through 260028, 115 VAC
Qty
Ref. No.
8 260433 KIT, switch, blue
(includes items 8a-8g)
Description
.
253718 KIT, switch, black
(includes items 8a-8g)
8a
8b
8c
8d
8e
8f
COVER, switch
BRACKET, switch
CAM, actuator switch
SWITCH, actuator assy.
SWITCH
SCREW, phillips, 8-32 x 3/8 in.
SCREW, phillips, 6-32 x 1/4 in.
1
1
1
1
1
2
1
8g
9
260061 ADAPTER, bung
1
10 260277 KIT, gear (includes 10a-10c)
10a (1c) GEAR
1
2
1
10b
KEY, drive
(1f/7c)
10c
SEAL, gear, cover
1
(1e/7b)
11 see pg. 2 ASSEMBLY, hose, 3/4 in.
(not shown)
1315G901 LABEL, warning (not shown)
14 15F074 NIPPLE, 3/4 in. x 3/4 in.
15 156589 ADAPTER, 90° swivel
1
1
Replacement Danger and Warning labels, tags, and
cards are available at no cost.
* Not used on models 260004, 260006, 260008,
260009, 260010, 260013, 260014, 260015, 260017,
260019, 260024, 260580, and 260581
**Used on 12 VDC and 24 VDC models only
14
311304J
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Data
Technical Data
Working pressure
Inlet size
10 psi (0.07 MPa, 0.7 bar)
1 in. npt
Outlet size
Weight
3/4 in. npt
20 lb (9 kg)
Power cable
Current draw
18 ft (5.5 m), 14 AWG (12 VDC and 24 VDC models only)
12 VDC models: 12.5 amps
24 VDC models: 7 amps
115 VAC models: 2 amps
230 VAC models: 1 amps
Duty cycle
30 min/hour
Suction tube
Wetted parts
1 in. x 34 in. (25.4 mm x 864 mm)
carbon steel with zinc plating, 416 and 302 stainless
®
steel, fluoroelastomer, Buna-N, Aluminum, Valox , Nylon,
Nitrile, PVC, Vellumoid,
®
Valox is a registered trademark of the General Electric Company
Performance Chart
ꢀꢁ
ꢀꢂꢃꢄꢁ ꢅꢂꢅꢃꢄ
ꢀꢂ
ꢀꢂꢆꢇꢁ ꢅꢂꢅꢆꢇ
ꢀꢃ
ꢀꢂꢈꢆꢁ ꢅꢂꢅꢈꢆ
ꢄ
ꢀꢂꢄꢉꢁ ꢅꢂꢅꢄꢉ
ꢅ
ꢀꢂꢉꢇꢁ ꢅꢂꢅꢉꢇ
ꢁ
"
ꢀꢂꢊꢋꢁ ꢅꢂꢅꢊꢋ
!
ꢂ
ꢀꢅꢂꢇꢉꢁ ꢅꢂꢅꢇꢉ
ꢃ
GPM
ꢆLPM
ꢀ
ꢁ
ꢆꢇꢈꢃ
ꢂ
ꢆꢅꢉꢈꢅ
ꢃ
ꢆꢁꢁꢈꢇ
ꢄ
ꢆꢊꢀꢈꢊ
ꢅꢀ
ꢆꢊꢇꢈꢋ
ꢅꢁ
ꢆꢂꢉꢈꢂ
ꢅꢂ
ꢆꢉꢊꢈꢀ
&,/7 2!4%
0!24 .5-"%23 ,%'%.$
! ꢌꢇꢊ6$# ꢍ ꢊꢉ6$#
0RESSURE
RELIEF OPENS
" ꢌꢇꢇꢄ6!# ꢍ ꢊꢎꢅ6!#
311304J
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Graco Standard Warranty
Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in
material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty
published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by
Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written
recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty
installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of
non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with
structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or
maintenance of structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of
the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned
to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs
will be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT
LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy
(including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or
consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT
MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to
the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these
warranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or
the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the
negligence of Graco, or otherwise.
FOR GRACO CANADA CUSTOMERS
The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into,
given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la
rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite
de ou en rapport, directement ou indirectement, avec les procédures concernées.
Graco Information
For the latest information about Graco products, visit www.graco.com.
TO PLACE AN ORDER, contact your Graco distributor or call to identify the nearest distributor.
Phone: 612-623-6928 or Toll Free: 1-800-533-9655, Fax: 612-378-3590
All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
This manual contains English. MM 311304
Graco Headquarters: Minneapolis
International Offices: Belgium, China, Japan, Korea
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440-1441
Copyright 2005, Graco Inc. is registered to ISO 9001
Revised March 2015
Download from Www.Somanuals.com. All Manuals Search And Download.
|
