When you installing AGP card, please make sure the following
notice is fully understood and practiced. If your AGP card has
"AGP 4X notch"(show below), please make sure your AGP card is
AGP 4X (1.5V).
Caution: AGP 2X card is not supported by Intel® 845(GE/PE) /
845(E/G) / 850(E). You might experience system unable to boot up
normally. Please insert anAGP 4X card.
Example 1: Diamond Vipper V770 golden finger is compatible with 2X/4X
mode AGP slot. It can be switched betweenAGP 2X(3.3V) or 4X(1.5V)
mode by adjusting the jumper. The factory default for this card is
2X(3.3V). The GA-8GEM667 Series (or anyAGP 4X only) motherboards
might not function properly, if you install this card without switching the
jumper to 4X(1.5) mode in it.
Example 2: Some ATi Rage 128 Pro graphics cards made by “Power
Color”, the graphics card manufacturer & some SiS 305 cards, their
golden finger is compatible with 2X(3.3V)/4X(1.5V) mode AGP slot, but
they support 2X(3.3V) only. The GA-8GEM667 Series (or anyAGP 4X
only) motherboards might not function properly, If you install this card in it.
Note : Although Gigabyte's AG32S(G) graphics card is based on
ATi Rage 128 Pro chip, the design of AG32S(G) is compliance
with AGP 4X(1.5V) specification. Therefore, AG32S (G)will work
fine with Intel® 845(GE/PE) /845(E/G) / 850(E) based motherboards.
Download from Www.Somanuals.com. All Manuals Search And Download.
Declaration of Conformity
We, Manufacturer/Importer
(full address)
G.B.T. Technology Träding GMbH
Ausschlager Weg 41, 1F, 20537 Hamburg, Germany
declare that the product
( description of the apparatus, system, installation to which it refers)
Mother Board
GA-8GEM667
is in conformity with
(reference to the specification under which conformity is declared)
in accordance with 89/336 EEC-EMC Directive
! EN 55011
Limits and methods of measurement
of radio disturbance characteristics of
industrial,scientific and medical (ISM
high frequency equipment
! EN 61000-3-2*
! EN 60555-2
Disturbances in supply systems cause
by household appliances and similar
electrical equipment “Harmonics”
Limits and methods of measurement
of radio disturbance characteristics of
broadcast receivers and associated
equipment
! EN 61000-3-3*
! EN 60555-3
Disturbances in supply systems cause
by household appliances and similar
electrical equipment “Voltage fluctuations”
! EN 55013
! EN 55014
Limits and methods of measurement
of radio disturbance characteristics of
household electrical appliances,
portable tools and similar electrical
apparatus
Generic emission standard Part 1:
! EN 50081-1
Residual commercial and light industry
! EN 50082-1
! EN 55081-2
Generic immunity standard Part 1:
Residual commercial and light industry
! EN 55015
! EN 55020
Limits and methods of measurement
of radio disturbance characteristics of
fluorescent lamps and luminaries
Generic emission standard Part 2:
Industrial environment
Immunity from radio interference of
broadcast receivers and associated
equipment
! EN 55082-2
Generic emission standard Part 2:
Industrial environment
! EN 55022
Limits and methods of measurement
of radio disturbance characteristics of
information technology equipment
! ENV 55104
! EN50091-2
lmmunity requirements for household
appliances tools and similar apparatus
! DIN VDE 0855
! part 10
Cabled distribution systems; Equipment
for receiving and/or distribution from
sound and television signals
EMC requirements for uninterruptible
power systems (UPS)
! part 12
(EC conformity marking)
! CE marking
The manufacturer also declares the conformity of above mentioned product
with the actual required safety standards in accordance with LVD 73/23 EEC
! EN 60065
! EN 60335
Safety requirements for mains operated
! EN 60950
Safety for information technology equipment
including electrical bussiness equipment
electronic and related apparatus for
household and similar general use
Safety of household and similar
electrical appliances
! EN 50091-1
General and Safety requirements for
uninterruptible power systems (UPS)
Manufacturer/Importer
Date : November 15, 2002
Timmy Huang
Timmy Huang
Signature:
Name:
(Stamp)
Download from Www.Somanuals.com. All Manuals Search And Download.
DECLARATION OF CONFORMITY
Per FCC Part 2 Section 2.1077(a)
Responsible Party Name:G.B.T. INC. (U.S.A.)
Address:
17358 Railroad Street
City of Industry, CA 91748
Phone/Fax No:(818) 854-9338/ (818) 854-9339
hereby declares that the product
Product Name:
Model Number:
Motherboard
GA-8GEM667
Conforms to the following specifications:
FCC Part 15, Subpart B, Section 15.107(a) and Section 15.109
(a),Class B Digital Device
Supplementary Information:
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful and (2) this device must accept any inference received,
including that may cause undesired operation.
Representative Person’s Name:
Signature:
ERIC LU
Eric Lu
Date: November15,2002
Download from Www.Somanuals.com. All Manuals Search And Download.
GA-8GEM667 Series
P4 Titan-DDR Motherboard
USER’S MANUAL
®
Pentium 4ProcessorMotherboard
Rev. 1001
12ME-8GEM667-1001
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Content
Item Checklist .........................................................................................4
WARNING!...............................................................................................4
Chapter 1 Introduction .............................................................................5
Features Summary ...................................................................................... 5
GA-8GEM667 Series Motherboard Layout................................................. 7
Chapter 2 Hardware Installation Process................................................9
Step 1: Install the Central Processing Unit (CPU)..................................... 10
Step1-1 : CPU Installation ............................................................................................... 10
Step1-2 : CPU Heat Sink Installation ..............................................................................11
Step 2: Install memory modules................................................................ 12
Step 3: Install expansion cards ................................................................. 13
Step 4: Connect ribbon cables, cabinet wires, and power supply ........... 14
Step 4-1: I/O Back Panel Introduction............................................................................ 14
Step 4-2 : Connectors Introduction................................................................................. 16
Chapter 3 BIOS Setup ..........................................................................23
The Main Menu (For example: BIOS Ver. : E2) ........................................ 24
Standard CMOS Features......................................................................... 26
Advanced BIOS Features .......................................................................... 29
Integrated Peripherals .............................................................................. 31
Power Management Setup ....................................................................... 35
PnP/PCI Configurations............................................................................. 37
PC Health Status........................................................................................ 38
Frequency/Voltage Control ........................................................................ 40
GA-8GEM667 Series Motherboard
- 2 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Top Performance ...................................................................................... 42
Load Fail-Safe Defaults............................................................................. 43
Load Optimized Defaults ........................................................................... 44
Set Supervisor/User Password .................................................................. 45
Save & Exit Setup....................................................................................... 46
Exit Without Saving ................................................................................... 47
Block Diagram........................................................................................... 49
Chapter 4 Technical Reference ............................................................49
Q-Flash Introduction.................................................................................. 61
@ BIOS Introduction.................................................................................. 65
Easy TuneTM 4 Introduction ....................................................................... 66
2-/4-/6-Channel Audio Function Introduction....................................67
Chapter 5 Appendix ..............................................................................75
- 3 -
Table of Content
Download from Www.Somanuals.com. All Manuals Search And Download.
Item Checklist
þ TheGA-8GEM667motherboard
þ IDE cable x 1/ Floppy cable x 1
þ CD for motherboard driver & utility
þ GA-8GEM667 series user’s manual
þ I/O Shield (*)
o 2 Port USB Cable x 1
o 4 Port USB Cable x 1
o SPDIF-KIT x 1 (SPD-KIT)
o IEEE 1394 Cable x1
o Audio Combo Kit x 1
o MotherboardSettingsLabel
o Quick PC Installation Guide
o RAID Manual
WARNING!
Computer motherboards and expansion cards contain very delicate Integrated Circuit (IC) chips. To
protect them against damage from static electricity, you should follow some precautions whenever you
work on your computer.
1. Unplug your computer when working on the inside.
2. Use a grounded wrist strap before handling computer components. If you do not have
one, touch both of your hands to a safely grounded object or to a metal object, such as
the power supply case.
3. Hold components by the edges and try not touch the IC chips, leads or connectors, or
othercomponents.
4. Place components on a grounded antistatic pad or on the bag that came with the
componentswheneverthecomponentsareseparatedfromthesystem.
5. Ensure that theATX power supply is switched off before you plug in or remove theATX
powerconnectoronthemotherboard.
Installing the motherboard to the chassis…
Ifthemotherboardhasmountingholes,buttheydon’tlineupwiththeholesonthebaseandthereare
no slots to attach the spacers, do not become alarmed you can still attach the spacers to the mounting
holes. Just cut the bottom portion of the spacers (the spacer may be a little hard to cut off, so be careful
ofyourhands). Inthiswayyoucanstillattachthemotherboardtothebasewithoutworryingaboutshort
circuits. Sometimes you may need to use the plastic springs to isolate the screw from the motherboard
PCB surface, because the circuit wire may be near by the hole. Be careful, don’t let the screw contact
any printed circuit write or parts on the PCB that are near the fixing hole, otherwise it may damage the
boardorcauseboardmalfunctioning.
“ * ” Only for GA-8GEM667.
GA-8GEM667 Series Motherboard
- 4 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Introduction
Features Summary
FormFactor
!
24.4cm x 22cm Micro-ATX size form factor, 4 layers PCB.
GA-8GEM667 Series Motherboard:
Motherboard
!
GA-8GEM667 and GA-8GEM667-C
®
CPU
!
Socket 478 for Intel® Micro FC-PGA2 Pentium 4 processor
! Support Intel ® Pentium ® 4 (Northwood, 0.13 m) processor
!
!
!
!
!
!
!
!
!
!
!
!
!
Support Intel ® Pentium ® 4 Processor with HTTechnology
®
Intel Pentium 4 400/533MHz FSB
2nd cache depends on CPU
Chipset
Chipset Intel 845GE HOST/AGP/Controller
ICH4 I/O Controller Hub
Memory
2 184-pin DDR DIMM sockets
Supports DDR333/DDR266 DIMM
Supports up to 2GB DRAM (Max)
Supports only 2.5V DDR DIMM
IT8712
I/O Control
Slots
1AGP slot 4X (1.5V) device support
3 PCI slot supports 33MHz & PCI 2.2 compliant
2 IDE bus master (UDMA33/ATA66/ATA100) IDE ports
for up to 4ATAPI devices
On-Board IDE
!
!
Supports PIO mode3,4 (UDMA33/ATA66/ATA100) IDE
& ATAPICD-ROM
On-BoardPeripherals
1 Floppy port supports 2 FDD with 360K, 720K,1.2M, 1.44M
and 2.88M bytes.
!
!
!
!
!
!
!
1 Parallel port supports Normal/EPP/ECP mode
2 Serial ports (COMA&COMB);1 VGA Port
6 USB 2.0/1.1 ports (2 x Rear, 4 xFront by cable)
1FrontAudioConnector
1 IrDA connector for IR/CIR
1 MODEN connector (*)
1FrontAudioconnector
!Due to (Intel 845PE/GE/GV) chipset architecture limitation, DDR 333 memory module is
only supported when using FSB 533 Pentium 4 processor.AFSB 400 Pentium 4 processor ......
will only support DDR 266 memory module
to be continued......
“ * ” Only for GA-8GEM667.
- 5 -
Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Monitor
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
CPU/System Fan Revolution detect
CPU/System Fan Fail Warning
CPU Overheat Warning
SystemVoltageDetect
On-Board VGA
On-BoardSound
Built in Intel 845GE Chipset
Realtek ALC650 CODEC
Line Out / 2 front speaker
Line In / 2 rear speaker(by s/w switch)
Mic In / center& subwoofer(by s/w switch)
SPDIF out
1 Buzzer
CD In / AUX In / Game port
BuilitinRTL8101LChipset
1 RJ 45 port
On-Board LAN *
PS/2 Connector
BIOS
PS/2 Keyboard interface and PS/2 Mouse interface
Licensed AWARD BIOS, 2M bit Flash ROM
SupportsQ-Flash
AdditionalFeatures
PS/2 Keyboard power on by password
PS/2 Mouse power on
External Modem wake up
STR(Suspend-To-RAM)
Wake on LAN (WOL)
AC Recovery
Poly fuse for keyboard over-current protection
USB KB/Mouse wake up from S3
Supports @BIOS
Supports EasyTune 4
Overclocking
Over Clock (DDR/AGP/CPU) by BIOS
Please set the CPU host frequency in accordance with your processor’s specifications.
We don’t recommend you to set the system bus frequency over the CPU’s specification
because these specific bus frequencies are not the standard specifications for CPU,
chipset and most of the peripherals. Whether your system can run under these specific
bus frequencies properly will depend on your hardware configurations, including CPU,
Chipsets,SDRAM,Cards….etc.
“ * ” Only for GA-8GEM667.
GA-8GEM667 Series Motherboard
- 6 -
Download from Www.Somanuals.com. All Manuals Search And Download.
HT functionality requirement content
"Enabling the functionality of Hyper-Threading Technology for your computer
systemrequiresallofthefollowingplatformcomponents:
- CPU: An Intel® Pentium 4 Processor with HT Technology
- Chipset:An Intel® Chipset that supports HTTechnology
- BIOS:ABIOS that supports HT Technology and has it enabled
- OS:An operation system that has optimizations for HTTechnology
- 7 -
Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
GA-8GEM667 Series Motherboard Layout
KB_MS
CPU_FAN
ATX
FDD
SOCKET478
ATX_12V
F_AUDIO
845GE
2X_DET
AGP
IDE1
IDE2
IT8712
CODEC
BUZZER
ICH4
PCI1
PCI2
SYS _FAN
BAT
SPDIF_O
PCI3
BIOS
* RTL
8101L
PWR_LED
IR_CIR
F_USB1
F_PANEL
F_USB2
5
CD_IN
* MODEM
WOL
COMB
CI
“ * ” Only for GA-8GEM667.
GA-8GEM667 Series Motherboard
- 8 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Hardware Installation Process
To set up your computer, you must complete the following steps:
Step 1- Install the Central Processing Unit (CPU)
Step 2- Install memory modules
Step 3- Install expansion cards
Step 4- Connect ribbon cables, cabinet wires, and power supply
Step 5- Setup BIOS software
Step 6- Install supporting software tools
Step 1 Step 4 Step 1
Step 2
Step 4
Step 4
Step 3
5
- 9 -
Hardware Installation Process
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 1: Install the Central Processing Unit (CPU)
Step1-1 : CPU Installation
Angling the
Socket
Actuation
Lever
0
rod to 65
2. Pulltherodtothe90-degreedirectly.
1. Anglingtherodto65-degreemaybefeel
akindof tight,andthencontinuepullthe
rod to 90-degree when a noise “cough”
made.
Pin1 indicator
Pin1 indicator
4. Locate Pin 1 in the socket and look
for a (golden) cut edge on the CPU
upper corner. Then insert the CPU
intothesocket.
3. CPU Top View
! Please make sure the CPU type is supported by the motherboard.
! If you do not match the CPU socket Pin 1 and CPU cut edge well, it will cause
improper installation. Please change the insert orientation.
GA-8GEM667 Series Motherboard
- 10 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Step1-2 : CPU Heat Sink Installation
2. Hook the other end of the
cooler bracket to the CPU
socket.
1. Hook one end of the cooler
bracket to the CPU socket first.
! Please use Intel approved cooling fan.
! We recommend you to apply the thermal tape to provide better heat
conduction between your CPU and heatsink.
(The CPU cooling fan might stick to the CPU due to the hardening of the
thermal paste. During this condition if you try to remove the cooling fan, you
might pull the processor out of the CPU socket alone with the cooling fan, and
might damage the processor. To avoid this from happening, we suggest you to
either use thermal tape instead of thermal paste, or remove the cooling fan with
extreme caution.)
! Make sure the CPU fan power cable is plugged in to the CPU fan connector,
this completes the installation.
! Please refer to CPU heat sink user’s manual for more detail installation
procedure.
- 11 -
Hardware Installation Process
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 2: Install memory modules
The motherboard has 2 dual inline memory module (DIMM) sockets. The BIOS will automatically
detectsmemorytypeandsize.Toinstallthememorymodule, justpushitverticallyintotheDIMMsocket
.The DIMM module can only fit in one direction due to the notch. Memory size can vary between
sockets.
Total Memory Sizes With Unbuffered DDR DIMM
Devices used on DIMM
64 Mbit (2Mx8x4 banks)
1 DIMM x 64 / x 72 2 DIMMs x 64 / x 72
128 MBytes
256 MBytes
64 MBytes
512 MBytes
128 MBytes
1 GBytes
64 Mbit (1Mx16x4 banks) 32 MBytes
128 Mbit(4Mx8x4 banks) 256 MBytes
128 Mbit(2Mx16x4 banks) 64 MBytes
256 Mbit(8Mx8x4 banks) 512 MBytes
256 Mbit(4Mx16x4 banks) 128 MBytes
512 Mbit(16Mx8x4 banks) 1 GBytes
512 Mbit(8Mx16x4 banks) 256 MBytes
256 MBytes
2 GBytes
512 MBytes
DDR1
S
DDR2
S
D
S
D
D
D
X
S
D
S
X
D:Double Sided DIMM S:Single Sided DIMM
X:Not Use
DDR
1. The DIMM socket has a notch, so the DIMM memory
module can only fit in one direction.
2. Insert the DIMM memory module vertically into the
DIMM socket. Then push it down.
3. Close the plastic clip at both edges of the DIMM
sockets to lock the DIMM module.
Reverse the installation steps when you wish to
remove the DIMM module.
! When STR/DIMM LED is ON, do not install/remove DIMM from socket.
! Please note that the DIMM module can only fit in one direction due to
the two notches. Wrong orientation will cause improper installation.
Please change the insert orientation.
GA-8GEM667 Series Motherboard
- 12 -
Download from Www.Somanuals.com. All Manuals Search And Download.
DDR Introduction
Established on the existing SDRAM industry infrastructure, DDR (Double Data Rate) memory is a
highperformanceandcost-effectivesolutionthatallowseasyadoptionformemoryvendors, OEMsand
systemintegrators.
DDR memory is a sensible evolutionary solution for the PC industry that builds on the existing
SDRAMinfrastructure, yetmakesawesomeadvancesinsolvingthesystemperformancebottleneckby
doubling the memory bandwidth. DDR SDRAM will offer a superior solution and migration path from
existing SDRAM designs due to its availability, pricing and overall market support. PC2100 DDR
memory(DDR266)doublesthedataratethroughreadingandwritingatboththerisingandfallingedgeof
the clock, achieving data bandwidth 2X greater than PC133 when running with the same DRAM clock
frequency. With peak bandwidth of 2.664GB per second, DDR memory enables system OEMs to build
high performance and low latency DRAM subsystems that are suitable for servers, workstations, high-
end PC's and value desktop SMA systems. With a core voltage of only 2.5 Volts compared to
conventional SDRAM's 3.3 volts, DDR memory is a compelling solution for small form factor desktops
andnotebookapplications.
Step 3: Install expansion cards
1. Readtherelatedexpansioncard’sinstructiondocumentbeforeinstalltheexpansioncardinto
thecomputer.
2. Remove your computer’s chassis cover, necessary screws and slot bracket from the computer.
3. Press the expansion card firmly into expansion slot in motherboard.
4. Be sure the metal contacts on the card are indeed seated in the slot.
5. Replace the screw to secure the slot bracket of the expansion card.
6. Replace your computer’s chassis cover.
7. Power on the computer, if necessary, setup BIOS utility of expansion card from BIOS.
8. Install related driver from the operating system.
Please carefully pull out the small white-
drawable bar at the end of the AGP slot when
you try to install/ Uninstall the AGP card.
Please align the AGP card to the onboard
AGP slot and press firmly down on the slot .
AGP Card
Make sure your AGP card is locked by the
small white- drawable bar.
When anAGP 2X (3.3V) card is installed the 2X_DET will light up, indicating a
non-supportedgraphicscardisinserted. Informingusersthatsystemmightnotbootup
normally due toAGP 2X (3.3V) is not supported by the chipset.
- 13 -
Hardware Installation Process
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 4: Connect ribbon cables, cabinet wires, and power
supply
Step 4-1: I/O Back Panel Introduction
#(*)
$
%
&
"
" PS/2 Keyboard and PS/2 Mouse Connector
ØThis connector supports standard PS/2 keyboard
PS/2 Mouse Connector
(6pinFemale)
and PS/2 mouse.
PS/2 Keyboard Connector
(6pinFemale)
Ø Before you connect your device(s) into USB
connector(s), please make sure your device(s)
such as USB keyboard,mouse, scanner, zip,
speaker..etc. Have a standard USB interface.
AlsomakesureyourOSsupportsUSBcontroller.
IfyourOSdoesnotsupportUSBcontroller,please
contact OS vendor for possible patch or driver
upgrade.Formoreinformationpleasecontactyour
OS or device(s) vendors.
# USB Connector
LAN(*) Connector
USB 0
USB 1
“ * ” Only for GA-8GEM667.
GA-8GEM667 Series Motherboard
- 14 -
Download from Www.Somanuals.com. All Manuals Search And Download.
$ Parallel Port and VGA Port / COMA Port
ParallelPort
ØThis mainboard sutports 1 standard COM port,
1 VGA port and 1 LPT port. Device like printer
can be connected to LPT port ; mouse and
modem etc can be connected to COM port.
(25pinFemale)
Serial Port
(9pinMale)
VGA Port
(15pinFemale)
% Game /MIDI Ports
ØThis connector supports joystick, MIDI keyboard
andotherrelateaudiodevices.
Joystick/ MIDI (15 pin Female)
& Audio Connectors
ØAfter install onboard audio driver, you may
connect speaker to Line Out jack, micro phone to
MIC In jack.
Device like CD-ROM , walkman etc can be
connected to Line-In jack.
Pleasenote:
Line Out
(Front
MIC In
(Center and Subwoofer)
You are able to use 2-/4-/6- channel audio feature
by S/W selection.
Speaker)
Ifyouwanttoenable6-channelfunction, youhave
2chooseforhardwareconnection.
Line In
(RearSpeaker)
Method1:
Connect “Front Speaker” to “Line Out”
Connect “Rear Speaker” to “Line In”
Connect “Center and Subwooferr” to “MIC Out “.
Method2:
Youcanrefertopage18, andcontactyournearest
dealerfor optional SUR_CEN cable.
If you want the detail information for 2-/4-/6-channel audio setup
installation, please refer to page 67.
- 15 -
Hardware Installation Process
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 4-2 : Connectors Introduction
1
3
4
6
10
11
5
21
8
20
13
15
2
9
5
19 12
16 17 18 14
7
1) CPU_FAN
2) SYS_FAN
3) ATX_12V
4) ATX
13) SPDIF_O
14) F_USB1/F_USB2
15) CI
16) IR_CIR
17) WOL
5) IDE1/IDE2
6) FDD
18) COM B
7) PWR_LED
8) 2X_DET
9) F_PANEL
10) F_AUDIO
11) SUR_CEN
12) CD_IN
19) MODEM (*)
20) BAT
21) CLR_PWD
“ * ” Only for GA-8GEM667.
GA-8GEM667 Series Motherboard
- 16 -
Download from Www.Somanuals.com. All Manuals Search And Download.
1) CPU_FAN (CPU FAN Connector)
" Please note, a proper installation of the CPU
cooler is essential to prevent the CPU from
runningunderabnormalconditionordamaged
by overheating.The CPU fan connector
supports Max. current up to 600 mA.
Sense
+12V
1
GND
2) SYS_FAN (System FAN Connector)
" This connector allows you to link with the
cooling fan on the system case to lower the
systemtemperature.
Sense
+12V
1
GND
3) ATX_12V (+12V Power Connector)
Ø This connector (ATX _12V) supplies the CPU
operationvoltage(Vcore).
1
2
GND
+12V
GND
+12V
If this "ATX_12V connector" is not
connected, systemcannotboot.
3
4
4)ATX (ATX Power)
Ø AC power cord should only be connected to
your power supply unit afterATX power cable
and other related devices are firmly connected
tothemainboard.
3.3V
3.3V
1
-12V
3.3V
GND
GND
GND
GND
PS-ON(Soft On/Off)
VCC
VCC
GND
GND
GND
-5V
Power Good
5V SB (Stand by +5V)
+12V
VCC
VCC
20
- 17 -
Hardware Installation Process
Download from Www.Somanuals.com. All Manuals Search And Download.
5) IDE1/ IDE2 [IDE1 / IDE2 Connector(Primary/Secondary)]
Ø ImportantNotice:
Please connect first harddisk to IDE1 and
connect CDROM to IDE2.
The red stripe of the ribbon cable must be
the same side with the Pin1.
1
IDE1
IDE2
6) FDD (Floppy Connector)
Ø Please connect the floppy drive ribbon cables
to FDD. It supports 360K,1.2M, 720K, 1.44M
and 2.88M bytes floppy disk types.
The red stripe of the ribbon cable must be the
same side with the Pin1.
1
7) PWR_LED
Ø PWR_LED is connect with the system power
indicator to indicate whether the system is
on/off. It will blink when the system enters
suspendmode.
MPD-
MPD-
MPD+
1
If you use dual color LED, power LED will turn
toanothercolor.
Ø When anAGP 2X (3.3V) card is installed the
2X_DET will light up, indicating a non-
supportedgraphicscardisinserted. Informing
users that system might not boot up normally
due toAGP 2X (3.3V) is not supported by the
chipset.
8 ) 2X_DET
GA-8GEM667 Series Motherboard
- 18 -
Download from Www.Somanuals.com. All Manuals Search And Download.
9 ) F_PANEL (2x10 pins connector)
1
1
1
1
2
1
20
19
1
HD (IDE Hard Disk Active LED) Pin 1: LED anode(+)
(Blue)
Pin 2: LED cathode(-)
Pin 1: VCC(+)
SPK (Speaker Connector)
(Amber)
Pin 2- Pin 3: NC
Pin 4: Data(-)
RES (Reset Switch)
(Green)
Open: Normal Operation
Close: Reset Hardware System
Open: Normal Operation
Close: Power On/Off
Pin 1: LED anode(+)
Pin 2: LED cathode(-)
NC
PW (Soft Power Connector)
(Red)
MSG(Message LED/Power/
Sleep LED)(Yellow)
NC( Purple)
Ø Please connect the power LED, PC speaker, reset switch and power switch etc of your chassis
front panel to the F_PANELconnector according to the pin assignment above.
ØIf you want to use "FrontAudio" connector,
you must remove 5-6, 9-10 Jumper. In order to
utilizethefrontaudioheader, yourchassis must
have front audio connector.Also please make
sure the pin assigment on the cable is the same
as the pin assigment on the MB header. To find
out if the chassis you are buying support front
audio connector, please contact your dealer.
10) F_AUDIO (Front Audio Connector)
10
9
RearAudio(L)
FrontAudio(L)
Reserved
FrontAudio(R)
REF
RearAudio (R)
POWER
GND
MIC
2
1
Ø Pleasecontactyournearestdealerforoptional
11) SUR_CEN
SUR_CEN cable.
BASS_OUT
SUR OUTR
CENTER_OUT
GND
SUR OUTL
1
- 19 -
Hardware Installation Process
Download from Www.Somanuals.com. All Manuals Search And Download.
Ø Connect CD-ROM or DVD-ROM audio out
12) CD_IN (CD Audio Line In)
totheconnector.
1
CD-R
GND
CD-L
Ø The SPDIF output is capable of providing
digital audio to external speakers or com
pressedAC3 data to an external Dolby
Digital Decoder. Use this feature only when
your stereosystemhasdigitalinput
function.
13) SPDIF_O
1
GND VCC
SPDIF Out
14 ) F_USB1/F_USB2 (F_USB1 ~ F_USB2 connector in yellow are for USB 2.0)
Ø Be careful with the polarity of the front USB
connector.Checkthepinassignmentwhileyou
connect the front USB cable.
USB Dy+
USB Dy-
Power
GND
USB Over Current
Pleasecontact yournearestdealerforoptional
front USB cable.
1
Power
USB Dx-
GND
USB Dx+
Ø This 2 pin connector allows your system to
enableordisablethe“CaseOpen”iteminBIOS
if the system case begin remove.
15) CI (CASE OPEN)
Signal
GND
1
Ø Make sure the pin 1 on the IR device is
aling with pin one the connector. To
enable the IR/CIR function on the board,
you are required to purchase an option IR/
CIRmodule. Fordetailinformationplease
contactyourautherizedGiga-Byte
distributor.
16 ) IR_CIR
1
To use IR function only, please connect IR
module to Pin1 to Pin5.
GA-8GEM667 Series Motherboard
- 20 -
Download from Www.Somanuals.com. All Manuals Search And Download.
17 ) WOL (Wake On Lan)
Ø This connector allows the remove servers to
managethesystemthatinstalledthis
mainboard via your network adapter which
also supports WOL.
1
+5V SB
GND
Signal
Ø Be careful with the polarity of the COMB
connector. Checkthepinassignment
while you connect the COMB cable.
Pleasecontactyournearestdealerforoptional
COMB cable.
18 ) COM B ( White connector)
1
Ø Pleasecontactyournearestdealerforoptional
19 ) Modem ( * )
Modem cable.
1
20 ) BAT (Battery)
CAUTION
v Danger of explosion if battery is incorrectly
replaced.
v Replace only with the same or equivalent
typerecommendedbythemanufacturer.
v Disposeofusedbatteriesaccordingtothe
manufacturer’sinstructions.
+
“ * ” Only for GA-8GEM667.
- 21 -
Hardware Installation Process
Download from Www.Somanuals.com. All Manuals Search And Download.
Ø When Jumper set to "open", the password that
set will be cleared. On the contrary when
Jumper set to "close", the current status
remains.
21 ) CLR_PWD
1
Close: Normal
1
Open: Clear Password
M PS, the function offers a solution for users who
forgetthepassword.
GA-8GEM667 Series Motherboard
- 22 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 BIOS Setup
BIOS Setup is an overview of the BIOS Setup Program. The program that allows users to modify the
basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it
retainstheSetupinformationwhenthepoweristurnedoff.
ENTERING
SETUP
Powering ON the computer and pressing <Del> immediately will allow you to enter Setup. If you require
more advanced BIOS settings, please go to “Advanced BIOS” setting menu.To enterAdvanced BIOS
setting menu, press “Ctrl+F1” key on the BIOS screen.
KEYS
CONTROL
<á>
<â>
<ß>
<à>
Enter
Move to previous item
Move to next item
Move to the item in the left hand
Move to the item in the right hand
Selectitem
<Esc>
Main Menu - Quit and not save changes into CMOS Status Page Setup Menu and
Option Page Setup Menu - Exit current page and return to Main Menu
<+/PgUp> Increase the numeric value or make changes
<-/PgDn> Decrease the numeric value or make changes
<F1>
<F2>
<F3>
<F4>
<F5>
<F6>
<F7>
<F8>
<F9>
<F10>
General help, only for Status Page Setup Menu and Option Page Setup Menu
Item Help
Reserved
Reserved
Restore the previous CMOS value from CMOS, only for Option Page Setup Menu
Load the file-safe default CMOS value from BIOS default table
LoadtheOptimizedDefaults
Q-Flashfunction
Reserved
Save all the CMOS changes, only for Main Menu
- 23 -
BIOS Setup
Download from Www.Somanuals.com. All Manuals Search And Download.
GETTING HELP
MainMenu
Theon-linedescriptionofthehighlightedsetupfunctionisdisplayedatthebottomofthescreen.
Status Page Setup Menu / Option Page Setup Menu
Press F1 to pop up a small help window that describes the appropriate keys to use and the possible
selections for the highlighted item. To exit the Help Window press <Esc>.
The Main Menu (For example: BIOS Ver. : E2)
Once you enterAward BIOS CMOS Setup Utility, the Main Menu (Figure 1) will appear on the screen.
The Main Menu allows you to select from eight setup functions and two exit choices. Use arrow keys to
select among the items and press <Enter> to accept or enter the sub-menu.
CMOS Setup Utility-Copyright (C) 1984-2002 Award Software
!Standard CMOS Features
!Advanced BIOS Features
!Integrated Peripherals
!Power Management Setup
!PnP/PCI Configurations
!PC Health Status
Top Performance
Load Fail-Safe Defaults
Load Optimized Defaults
Set Supervisor Password
Set User Password
Save & Exit Setup
!Frequency/Voltage Control
ESC:Quit
Exit Without Saving
"#$%:Select Item
F10:Save & Exit Setup
F8: Q-Flash
Time, Date, Hard Disk Type...
Figure 1: Main Menu
If you can’t find the setting you want, please press ”Ctrl+F1” to
search the advanced option widden.
!
!
StandardCMOSFeatures
This setup page includes all the items in standard compatible BIOS.
AdvancedBIOSFeatures
This setup page includes all the items of Award special enhanced features.
GA-8GEM667 Series Motherboard
- 24 -
Download from Www.Somanuals.com. All Manuals Search And Download.
!
!
!
!
!
!
!
Integrated Peripherals
Thissetuppageincludesallonboardperipherals.
PowerManagementSetup
ThissetuppageincludesalltheitemsofGreenfunctionfeatures.
PnP/PCI Configurations
This setup page includes all the configurations of PCI & PnP ISA resources.
PC Health Status
This setup page is the System auto detectTemperature, voltage, fan, speed.
Frequency/VoltageControl
This setup page is control CPU’s clock and frequency ratio.
TopPerformance
If you wish to maximize the performance of your system, set "Top Performance" as "Enabled".
Load Fail-Safe Defaults
Fail-Safe Defaults indicates the value of the system parameters which the system would
beinsafeconfiguration.
!
!
LoadOptimizedDefaults
Optimized Defaults indicates the value of the system parameters which the system would
beinbestperformanceconfiguration.
Set Supervisor password
Change, set, or disable password. It allows you to limit access to the system and Setup,
or just to Setup.
!
!
!
Set User password
Change, set, or disable password. It allows you to limit access to the system.
Save & Exit Setup
Save CMOS value settings to CMOS and exit setup.
Exit Without Saving
Abandon all CMOS value changes and exit setup.
- 25 -
BIOS Setup
Download from Www.Somanuals.com. All Manuals Search And Download.
Standard CMOS Features
CMOS Setup Utility-Copyright (C) 1984-2002 Award Software
Standard CMOS Features
Fri, May 3 2002
17:56:23
Date (mm:dd:yy)
Time (hh:mm:ss)
Item Help
Menu Level &
Change the day, month,
!IDE Primary Master
!IDE Primary Slave
!IDE Secondary Master
!IDE Secondary Slave
None
None
None
None
year
<Week>
Sun. to Sat.
Drive A
1.44M, 3.5 in.
None
<Month>
Drive B
Jan. to Dec.
Floppy 3 Mode Support
Disabled
<Day>
Halt On
All, But Keyboard
1 to 31 (or maximum
allowed in the month)
Base Memory
Extended Memory
Total Memory
640K
130048K
131072K
<Year>
1999 to 2098
"#$%: Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults
Figure 2: Standard CMOS Features
! Date
The date format is <week>, <month>, <day>, <year>.
!Week
!Month
!Day
The week, from Sun to Sat, determined by the BIOS and is display only
The month, Jan. Through Dec.
The day, from 1 to 31 (or the maximum allowed in the month)
The year, from 1999 through 2098
!Year
GA-8GEM667 Series Motherboard
- 26 -
Download from Www.Somanuals.com. All Manuals Search And Download.
! Time
Thetimesformatin<hour><minute><second>.Thetimeiscalculatedbaseonthe24-hourmilitary-
time clock. For example, 1 p.m. is 13:00:00.
! IDE Primary Master, Slave / IDE Secondary Master, Slave
ThecategoryidentifiesthetypesofharddiskfromdriveCtoFthathasbeeninstalledinthecomputer.
There are two types: auto type, and manual type. Manual type is user-definable; Auto type which will
automatically detect HDD type.
Note that the specifications of your drive must match with the drive table. The hard disk will not work
properly if you enter improper information for this category.
If you select User Type, related information will be asked to enter to the following items. Enter the
information directly from the keyboard and press <Enter>. Such information should be provided in the
documentation form your hard disk vendor or the system manufacturer.
!CYLS.
Number of cylinders
Number of heads
Write precomp
!HEADS
!PRECOMP
!LANDZONE
Landing zone
!SECTORSNumber of sectors
If a hard disk has not been installed select NONE and press <Enter>.
! Drive A / Drive B
The category identifies the types of floppy disk drive A or drive B that has been installed in the
computer.
!None
No floppy drive installed
!360K, 5.25 in.
!1.2M, 5.25 in.
5.25 inch PC-type standard drive; 360K byte capacity.
5.25 inch AT-type high-density drive; 1.2M byte capacity
(3.5 inch when 3 Mode is Enabled).
!720K, 3.5 in.
!1.44M, 3.5 in.
!2.88M, 3.5 in.
3.5 inch double-sided drive; 720K byte capacity
3.5 inch double-sided drive; 1.44M byte capacity.
3.5 inch double-sided drive; 2.88M byte capacity.
- 27 -
BIOS Setup
Download from Www.Somanuals.com. All Manuals Search And Download.
! Floppy3ModeSupport(forJapanArea)
!Disabled
!Drive A
!Drive B
!Both
Normal Floppy Drive. (Default value)
Drive A is 3 mode Floppy Drive.
Drive B is 3 mode Floppy Drive.
Drive A & B are 3 mode Floppy Drives.
!Halt on
The category determines whether the computer will stop if an error is detected during power up.
!NO Errors
The system boot will not stop for any error that may be detected
and you will be prompted.
!All Errors
Whenever the BIOS detects a non-fatal error the system will be stopped.
!All, But Keyboard The system boot will not stop for a keyboard error; it will stop for
all other errors. (Default value)
!All, But Diskette
The system boot will not stop for a disk error; it will stop for all
other errors.
!All, But Disk/Key The system boot will not stop for a keyboard or disk error; it will
stop for all other errors.
! Memory
The category is display-only which is determined by POST (Power On Self Test) of the BIOS.
Base Memory
The POST of the BIOS will determine the amount of base (or conventional) memory
installed in the system.
The value of the base memory is typically 512 K for systems with 512 K memory
installed on the motherboard, or 640 K for systems with 640 K or more memory
installedonthemotherboard.
ExtendedMemory
The BIOS determines how much extended memory is present during the POST.
This is the amount of memory located above 1 MB in the CPU’s memory
address map.
GA-8GEM667 Series Motherboard
- 28 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced BIOS Features
CMOS Setup Utility-Copyright (C) 1984-2002 Award Software
Advanced BIOS Features
[Floppy]
First Boot Device
Item Help
Second Boot Device
Third Boot Device
Boot Up Floppy Seek
Password Check
[HDD-0]
[CDROM]
[Disabled]
[Setup]
Menu Level &
Select Boot Device
priority
# CPU Hyper-Threading
Init Display First
Enabled
[Floppy]
[Onboard/AGP]
Boot from floppy
[LS120]
Boot from LS120
[HDD-0]
Boot from First HDD
[HDD-1]
Boot from second HDD
"#$%: Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults
Figure 3: Advanced BIOS Features
“ # ” System will detect automatically and show up when you install the Intel®
Pentium® 4 processor with HT Technology.
! First / Second / Third Boot Device
!Floppy
!LS120
Select your boot device priority by Floppy.
Select your boot device priority by LS120.
Select your boot device priority by HDD-0~3.
Select your boot device priority by SCSI.
Select your boot device priority by CDROM.
Select your boot device priority by ZIP.
!HDD-0~3
!SCSI
!CDROM
!ZIP
!USB-FDD
!USB-ZIP
!USB-CDROM
!USB-HDD
!LAN
Select your boot device priority by USB-FDD.
Select your boot device priority by USB-ZIP.
Select your boot device priority by USB-CDROM.
Select your boot device priority by USB-HDD.
Select your boot device priority by LAN.
Select your boot device priority by Disabled.
!Disabled
- 29 -
BIOS Setup
Download from Www.Somanuals.com. All Manuals Search And Download.
! BootUpFloppySeek
During POST, BIOS will determine the floppy disk drive installed is 40 or 80 tracks. 360 K type is
40 tracks 720 K, 1.2 M and 1.44 M are all 80 tracks.
!Enabled
!Disabled
BIOS searches for floppy disk drive to determine it is 40 or 80 tracks. Note
that BIOS can not tell from 720 K, 1.2 M or 1.44 M drive type as they are
all 80tracks.
BIOS will not search for the type of floppy disk drive by track number. Note
that there will not be any warning message if the drive installed is 360 K.
(Default value)
! Password Check
!System
The system can not boot and can not access to Setup page will be denied
if the correct password is not entered at the prompt.
!Setup
The system will boot, but access to Setup will be denied if the correct
password is not entered at the prompt. (Default value)
!CPUHyper-Threading
!Enabled
Enables CPU Hyper Threading Feature. Please note that this feature is only
working for operating system with multi processors mode supported.
(Default value)
!Disabled
Disables CPU Hyper Threading.
!InitDisplay First
!AGP
!PCI
Set Init Display First to AGP. (Default value)
Set Init Display First to PCI.
GA-8GEM667 Series Motherboard
- 30 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Integrated Peripherals
CMOS Setup Utility-Copyright (C) 1984-2002 Award Software
Integrated Peripherals
[Enabled]
On-Chip Primary PCI IDE
On-Chip Secondary PCI IDE
IDE1 Conductor Cable
Item Help
[Enabled]
[Auto]
Menu Level &
If a hard disk
controller card is
IDE2 Conductor Cable
[Auto]
USB Controller
[Enabled]
[Disabled]
[Disabled]
[Auto]
used, set at Disable
USB Keyboard Support
USB Mouse Support
AC97 Audio
[Enabled]
Enable onboard IDE
Onboard H/W LAN (*)
Onboard LAN Boot ROM (*)
Onboard Serial Port 1
Onboard Serial Port 2
UART Mode Select
xUR2 Duplex Mode
Onboard Parallel Port
Parallel Port Mode
x ECP Mode Use DMA
Game Port Address
Midi Port Address
Midi Port IRQ
[Enabled]
[Disabled]
[3F8/IRQ4]
[2F8/IRQ3]
[Normal]
Half
PORT
[378/IRQ7]
[SPP]
[Disabled]
Disable onboard IDE
PORT
3
[201]
[330]
[10]
CIR Port Address
[Disabled]
11
xCIR Port IRQ
"#$%: Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5:Previous Values
F6:Fail-Safe Defaults
F7:Optimized Defaults
Figure 4: Integrated Peripherals
! On-ChipPrimaryPCIIDE
!Enabled
!Disabled
Enable onboard 1st channel IDE port. (Default value)
Disable onboard 1st channel IDE port.
! On-ChipSecondaryPCIIDE
!Enabled
!Disabled
Enable onboard 2nd channel IDE port. (Default value)
Disable onboard 2nd channel IDE port.
“ * ” Only for GA-8GEM667.
- 31 -
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup
! IDE1ConductorCable
!Auto
Will be automatically detected by BIOS. (Default Value)
!ATA66/100
Set IDE1 Conductor Cable to ATA66/100 (Please make sure your IDE device
and cable is compatible with ATA66/100).
!ATA33
Set IDE1 Conductor Cable to ATA33 (Please make sure your IDE device and
cable is compatible with ATA33).
! IDE2ConductorCable
!Auto
Will be automatically detected by BIOS. (Default Value)
!ATA66/100
Set IDE2 Conductor Cable to ATA66/100 (Please make sure your IDE device
and cable is compatible with ATA66/100).
!ATA33
Set IDE2 Conductor Cable to ATA33 (Please make sure your IDE device and
cable is compatible with ATA33).
! USB Controller
!Enabled
!Disabled
Enable USB Controller. (Default value)
Disable USB Controller.
! USBKeyboardSupport
!Enabled
!Disabled
Enable USB Keyboard Support.
Disable USB Keyboard Support. (Default value)
! USB Mouse Support
!Enabled
!Disabled
Enable USB Mouse Support.
Disable USB Mouse Support. (Default value)
! AC97Audio
!Auto
Enable onboard AC'97 audio function. (Default Value)
Disable this function.
!Disabled
! OnboardH/WLAN(*)
!Enabled
!Disabled
Enabled onboard H/W LAN Function.(Default value)
Disabled onboard H/W LAN Function
“ * ” Only for GA-8GEM667.
GA-8GEM667 Series Motherboard
- 32 -
Download from Www.Somanuals.com. All Manuals Search And Download.
! OnboardLANBootROM(*)
!Enabled
!Disabled
Enabled onboard LAN Boot ROM.
Disabled onboard LAN Boot ROM.(Default value)
! Onboard Serial Port 1
!Auto
BIOS will automatically setup the port 1 address.
!3F8/IRQ4
!2F8/IRQ3
!3E8/IRQ4
!2E8/IRQ3
!Disabled
Enable onboard Serial port 1 and address is 3F8. (Default value)
Enable onboard Serial port 1 and address is 2F8.
Enable onboard Serial port 1 and address is 3E8.
Enable onboard Serial port 1 and address is 2E8.
Disable onboard Serial port 1.
! Onboard Serial Port 2
!Auto
BIOS will automatically setup the port 2 address.
!3F8/IRQ4
!2F8/IRQ3
!3E8/IRQ4
!2E8/IRQ3
!Disabled
Enable onboard Serial port 2 and address is 3F8.
Enable onboard Serial port 2 and address is 2F8. (Default value)
Enable onboard Serial port 2 and address is 3E8.
Enable onboard Serial port 2 and address is 2E8.
Disable onboard Serial port 2.
! UARTModeSelect
(This item allows you to determine which Infra Red(IR) function of Onboard I/O chip)
!ASKIR
!IrDA
Set onboard I/O chip UART to ASKIR Mode.
Set onboard I/O chip UART to IrDA Mode.
!Normal
Set onboard I/O chip UART to Normal Mode. (Default Value)
! UR2DuplexMode
!Half
!Full
IR Function Duplex Half. (Default Value)
IR Function Duplex Full.
! OnboardParallelport
!378/IRQ7
!278/IRQ5
!Disabled
!3BC/IRQ7
Enable onboard LPT port and address is 378/IRQ7. (Default Value)
Enable onboard LPT port and address is 278/IRQ5.
Disable onboard LPT port.
Enable onboard LPT port and address is 3BC/IRQ7.
- 33 -
BIOS Setup
Download from Www.Somanuals.com. All Manuals Search And Download.
!Parallel Port Mode
!SPP
Using Parallel port as Standard Parallel Port. (Default Value)
!EPP
Using Parallel port as Enhanced Parallel Port.
Using Parallel port as Extended Capabilities Port.
Using Parallel port as ECP & EPP mode.
!ECP
!ECP+EPP
!ECPModeUseDMA
!3
!1
Set ECP Mode Use DMA to 3. (Default Value)
Set ECP Mode Use DMA to 1.
!Game PortAddress
!201
Set Game Port Address to 201. (Default Value)
!209
Set Game Port Address to 209.
Disable this function.
!Disabled
!Midi PortAddress
!300
Set Midi Port Address to 300.
!330
Set Midi Port Address to 330.(Default Value)
Disable this function.
!Disabled
!Midi Port IRQ
!5
Set Midi Port IRQ to 5.
!10
Set Midi Port IRQ to 10. (Default Value)
!CIR PortAddress
!310
!320
Set CIR Port Address to 310.
Set CIR Port Address to 320.
!Disabled
Disable this function.(Default Value)
!CIR Port IRQ
!5
Set CIR Port IRQ to 5.
!11
Set CIR Port IRQ to 11. (Default Value)
GA-8GEM667 Series Motherboard
- 34 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Power Management Setup
CMOS Setup Utility-Copyright (C) 1984-2002 Award Software
Power Management Setup
[S1(POS)]
ACPI Suspend Type
Item Help
Soft-Off by PWR_BTTN
PME Event Wake Up
[Instant-Off]
[Enabled]
Menu Level &
ModemRingOn/WakeOnLan
Resume by Alarm
[Enabled]
[Disabled]
Everyday
0 0 0
[Disabled]
[Disabled]
Enter
[S1]
Set suspend type to
Power On Suspend under
ACPI OS
x Date (of Month) Alarm
x Time (hh:nn:ss)
Power On By Mouse
Power On By Keyboard
x KB Power ON Password
AC Back Function
[S3]
Set suspend type to
Suspend to RAM under
ACPI OS
[Soft-Off]
"#$%: Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5:Previous Values
F6:Fail-Safe Defaults
F7:Optimized Defaults
Figure 5: Power Management Setup
! ACPISuspendType
!S1(POS)
!S3(STR)
Set ACPI suspend type to S1. (Default Value)
Set ACPI suspend type to S3.
! Soft-offbyPWR_BTTN
!Instant-off
Press power button then Power off instantly. (Default value)
!Delay 4 Sec. Press power button 4 sec to Power off. Enter suspend if button is pressed less
than 4 sec.
! PMEEventWakeUp
!Disabled
!Enabled
Disable this function.
Enable PME Event Wake up. (Default Value)
- 35 -
BIOS Setup
Download from Www.Somanuals.com. All Manuals Search And Download.
!Modem Ring On/ WakeOnLAN (When AC Back Function is set to [Soft-Off])
M You can enable wake on LAN feature by the "ModemRingOn/WakeOnLAN" or "PME Event Wake
up" when the M/B has "WOL" onboard connector. Only enabled the feature by "PME Event Wake
up".
M An incoming call via modem awakes the system from its soft-off mode.
M When set at Enabled, an input signal comes from the other client/server on the LAN awaks the
system from a soft off state if connected over LAN.
!Disabled
!Enabled
Disabled Modem Ring On / Wake On LAN function.
Enabled Modem Ring On / Wake On LAN function.
! Resume byAlarm
You can set "Resume by Alarm" item to enabled and key in Data/time to power on system.
!Disabled
!Enabled
Disable this function. (Default Value)
Enable alarm function to POWER ON system.
If RTC Alarm Lead To Power On is Enabled.
Date ( of Month) Alarm :
Everyday, 1~31
Time ( hh: mm: ss) Alarm :
(0~23) : (0~59) : (0~59)
! Power On By Mouse
!Disabled
Disabled this function. (Default value)
Double click on PS/2 mouse left button.
!Mouse Click
!Power On By Keyboard
!Password
!Disabled
Enter from 1 to 5 characters to set the Keyboard Power On Password.
Disabled this function. (Default value)
!Keyboard 98
If your keyboard have “POWER Key” button, you can press the key to
power on your system.
!KB Power ON Password
!Enter
Input password (from 1 to 5 characters) and press Enter to set the Key
board Power On Password.
!AC Back Function
!Memory
!Soft-Off
!Full-On
System power on depends on the status before AC lost.
Always in Off state when AC back. (Default value)
Always power on the system when AC back.
GA-8GEM667 Series Motherboard
- 36 -
Download from Www.Somanuals.com. All Manuals Search And Download.
PnP/PCI Configurations
CMOS Setup Utility-Copyright (C) 1984-2002 Award Software
PnP/PCI Configurations
PCI 1 IRQ Assignment
PCI 2 IRQ Assignment
PCI 3 IRQ Assignment
[Auto]
[Auto]
[Auto]
Item Help
Menu Level &
"#$%: Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5:Previous Values
F6:Fail-Safe Defaults
F7:Optimized Defaults
Figure 6: PnP/PCI Configurations
! PCI 1 IRQAssignment
!Auto
Auto assign IRQ to PCI 1/PCI 5. (Default value)
Set IRQ 3,4,5,7,9,10,11,12,14,15 to PCI 1/PCI 5.
!3,4,5,7,9,10,11,12,14,15
! PCI 2 IRQAssignment
!Auto
Auto assign IRQ to PCI 2. (Default value)
Set IRQ 3,4,5,7,9,10,11,12,14,15 to PCI 2.
!3,4,5,7,9,10,11,12,14,15
! PCI 3 IRQ Assignment
!Auto
Auto assign IRQ to PCI 3. (Default value)
Set IRQ 3,4,5,7,9,10,11,12,14,15 to PCI 3.
!3,4,5,7,9,10,11,12,14,15
- 37 -
BIOS Setup
Download from Www.Somanuals.com. All Manuals Search And Download.
PC Health Status
CMOS Setup Utility-Copyright (C) 1984-2002 Award Software
PC Health Status
[Disabled]
Reset Case Open Status
Case Opened
Item Help
[No]
Menu Level &
VCORE
1.71V
+1.5V
1.488V
3.29V
+3.3V
+5V
4.99V
+12V
11.73V
40°C
Current CPU Temperature
Current CPU FAN Speed
Current SYSTEM FAN Speed
CPU Warning Temperature
CPU FAN Fail Warning
SYSTEM FAN Fail Warning
4821 RPM
0 RPM
[Disabled]
[Disabled]
[Disabled]
"#$%: Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults
Figure 7: PC Health Status
!Reset Case Open Status
!Case Opened
If the case is closed, "Case Opened" will show "No".
If the case have been opened, "Case Opened" will show "Yes".
If you want to reset "Case Opened" value, set "Reset Case Open Status" to
"Enabled" and save CMOS, your computer will restart.
! Current Voltage (V) VCORE / +1.5V / +3.3V / +5V / +12V
!Detect system’s voltage status automatically.
!Current CPU Temperature
!Detect CPU Temp. automatically.
GA-8GEM667 Series Motherboard
- 38 -
Download from Www.Somanuals.com. All Manuals Search And Download.
! CurrentCPU/SYSTEMFANSpeed(RPM)
!Detect CPU/SYSTEM Fan speed status automatically.
!CPU Warning Temperature
!60°C / 140°F
!70°C / 158°F
!80°C / 176°F
!90°C / 194°F
!Disabled
Monitor CPU Temp. at 60°C / 140°F.
Monitor CPU Temp. at 70°C / 158°F.
Monitor CPU Temp. at 80°C / 176°F.
Monitor CPU Temp. at 90°C / 194°F.
Disable this function.(Default value)
! CPU FAN FailWarning
!Disabled
!Enabled
Fan Warning Function Disable. (Default value)
Fan Warning Function Enable.
! SYSTEMFANFailWarning
!Disabled
!Enabled
Fan Warning Function Disable. (Default value)
Fan Warning Function Enable.
- 39 -
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Setup
Frequency/Voltage Control
CMOS Setup Utility-Copyright (C) 1984-2002 Award Software
Frequency/Voltage Control
CPU Clock Ratio
15X
Item Help
CPU Host Clock Control
"CPU Host Frequency (Mhz)
"Fixed PCI/AGP Frequency
Host/DRAM Clock ratio
Memory Frequency (Mhz)
PCI/AGP Frequency (Mhz)
Disabled
133
Menu Level &
33/66
Auto
266
33/66
"#$%: Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F3: Language
F5:Previous Values F6:Fail-Safe Defaults
F7:Optimized Defaults
Figure 8: Frequency/Voltage Control
"Those items will be available when "CPU Host Clock Control" is set to Enabled.
!CPU Clock Ratio
This setup option will automatically assign by CPU detection.
For Willamette CPU:
8X~23X default: 14X
For C-Stepping P4:
8X,10X~24X default: 15X
For Northwood CPU:
12X~24X default: 16X
The option will display “Locked” and read only if the CPU ratio is not changeable.
!CPU Host Clock Control
Note: If system hangs up before enter CMOS setup utility, wait for 20 sec for times out reboot . When
time out occur, system will reset and run at CPU default Host clock at next boot.
!Disable
!Enable
Disable CPU Host Clock Control.(Default value)
Enable CPU Host Clock Control.
GA-8GEM667 Series Motherboard
- 40 -
Download from Www.Somanuals.com. All Manuals Search And Download.
!CPUHostFrequency(MHz)
!100MHz ~ 355MHz
Set CPU Host Clock from 100MHz to 355MHz.
Incorrect using it may cause your system broken. For power End-User use only!
!FixedPCI/AGPFrequency
!You can choose those mode to adjust PCI/AGP frequency. (Select PCI/AGP frequency
asynchronous with CPU frequency).
!Host/DRAM Clock Ratio
for FSB(Front Side Bus) frequency=400MHz,
!2.0
Memory Frequency = Host clock X 2.0.
!2.66
!Auto
Memory Frequency = Host clock X 2.66.
Set Memory frequency by DRAM SPD data. (Default value)
for FSB(Front Side Bus) frequency=533MHz,
!2.0
!2.5
!Auto
Memory Frequency = Host clock X 2.0.
Memory Frequency = Host clock X 2.5.
Set Memory frequency by DRAM SPD data. (Default value)
!MemoryFrequency(Mhz)
!The values depend on CPU Host Frequency(Mhz) .
!PCI/AGPFrequency(Mhz)
!The values depend on Fixed PCI/AGP Frequency.
- 41 -
BIOS Setup
Download from Www.Somanuals.com. All Manuals Search And Download.
Top Performance
CMOS Setup Utility-Copyright (C) 1984-2002 Award Software
!Standard CMOS Features
!Advanced Chipset Features
Top Performance
Load Fail-Safe Defaults
!Integrated Pe
Top Performance
!Power Mana
Disabled...................[ "]
!PnP/PCI Con
Enabled................... [
]
!PC Health St
!Frequency/V
ESC:Quit
"#: Move
ENTER: Accept
F8: Q-Flash
ESC: Abort
Figure 9: Top Performance
TopPerformance
If you wish to maximize the performance of your system, set "Top Performance" as "Enabled".
!Disabled Disable this function. (Default Value)
!Enabled Enable Top Performance function.
You must check whether your RAM&CPU support over clock when you set "Top Performance"
to " Enabled"
GA-8GEM667 Series Motherboard
- 42 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Load Fail-Safe Defaults
CMOS Setup Utility-Copyright (C) 1984-2002 Award Software
!Standard CMOS Features
!Advanced Chipset Features
!Integrated Peripherals
Top Performance
Load Fail-Safe Defaults
Load Optimized Defaults
Save & Exit Setup
!Power Man
Load Fail-Safe Defaults? (Y/N)?Y
!PnP/PCI Co
!PC Health Status
!Frequency/Voltage Control
ESC:Quit
Exit Without Saving
"#$%:Select Item
F10:Save & Exit Setup
F8: Q-Flash
Load Fail-Safe Defaults
Figure 10: Load Fail-Safe Defaults
Load Fail-Safe Defaults
Fail-Safedefaultscontainthemostappropriatevaluesofthesystemparametersthatallow
minimumsystemperformance.
- 43 -
BIOS Setup
Download from Www.Somanuals.com. All Manuals Search And Download.
Load Optimized Defaults
CMOS Setup Utility-Copyright (C) 1984-2002 Award Software
!Standard CMOS Features
!Advanced BIOS Features
!Integrated Peripherals
Top Performance
Load Fail-Safe Defaults
Load Optimized Defaults
Save & Exit Setup
!Power Ma
Load Optimized Defaults? (Y/N)?Y
!PnP/PCI
!PC Health Status
!Frequency/Voltage Control
ESC:Quit
Exit Without Saving
"#$%:Select Item
F10:Save & Exit Setup
F8: Q-Flash
Load Optimized Defaults
Figure 11: Load Optimized Defaults
LoadOptimizedDefaults
Selecting this field loads the factory defaults for BIOS and Chipset Features which the
systemautomaticallydetects.
GA-8GEM667 Series Motherboard
- 44 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Set Supervisor/User Password
CMOS Setup Utility-Copyright (C) 1984-2002 Award Software
!Standard CMOS Features
!Advanced BIOS Features
!Integrated Peripherals
Top Performance
Load Fail-Safe Defaults
Load Optimized Defaults
Save & Exit Setup
!Power Man
Enter Password:
!PnP/PCI C
!PC Health Status
!Frequency/Voltage Control
ESC:Quit
Exit Without Saving
"#$%:Select Item
F10:Save & Exit Setup
F8: Q-Flash
Change/Set/Disable Password
Figure 12: Password Setting
Whenyouselectthisfunction, thefollowingmessagewillappearatthecenterofthescreentoassist
you in creating a password.
Type the password, up to eight characters, and press <Enter>. You will be asked to confirm the
password. Type the password again and press <Enter>. You may also press <Esc> to abort the
selection and not enter a password.
To disable password, just press <Enter> when you are prompted to enter password. Amessage
“PASSWORD DISABLED” will appear to confirm the password being disabled. Once the password is
disabled, the system will boot and you can enter Setup freely.
The BIOS Setup program allows you to specify two separate passwords:
SUPERVISOR PASSWORD and a USER PASSWORD. When disabled, anyone may access
all BIOS Setup program function. When enabled, the Supervisor password is required for entering the
BIOS Setup program and having full configuration fields, the User password is required to access only
basic items.
If you select “System” at “Password Check” in Advance BIOS Features Menu, you will be
prompted for the password every time the system is rebooted or any time you try to enter Setup Menu.
If you select “Setup” at “Password Check” in Advance BIOS Features Menu, you will be prompted
only when you try to enter Setup.
- 45 -
BIOS Setup
Download from Www.Somanuals.com. All Manuals Search And Download.
Save & Exit Setup
CMOS Setup Utility-Copyright (C) 1984-2002 Award Software
!Standard CMOS Features
!Advanced BIOS Features
!Integrated Peripherals
Top Performance
Load Fail-Safe Defaults
Load Optimized Defaults
Set Supervisor Password
!Power Management Setup
!PnP/PCI C
Save to CMOS and EXIT (Y/N)? Y
!PC Health
!Frequency/Voltage Control
ESC:Quit
Exit Without Saving
"#$%:Select Item
F10:Save & Exit Setup
F8: Q-Flash
Save Data to CMOS
Figure 13: Save & Exit Setup
Type “Y” will quit the Setup Utility and save the user setup value to RTC CMOS.
Type “N” will return to Setup Utility.
GA-8GEM667 Series Motherboard
- 46 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Exit Without Saving
CMOS Setup Utility-Copyright (C) 1984-2002 Award Software
!Standard CMOS Features
!Advanced BIOS Features
!Integrated Peripherals
Top Performance
Load Fail-Safe Defaults
Load Optimized Defaults
Set Supervisor Password
!Power Management Setup
!PnP/PCI Co
Quit Without Saving (Y/N)? N
!PC Health S
!Frequency/Voltage Control
ESC:Quit
Exit Without Saving
"#$%:Select Item
F10:Save & Exit Setup
F8: Q-Flash
Abandon all Data
Figure 14: Exit Without Saving
Type “Y” will quit the Setup Utility without saving to RTC CMOS.
Type “N” will return to Setup Utility.
- 47 -
BIOS Setup
Download from Www.Somanuals.com. All Manuals Search And Download.
GA-8GEM667 Series Motherboard
- 48 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 Technical Reference
Block Diagram
Pentium 4
CPUCLK+/- (100/133MHz)
Socket 478
CPU
AGP 4X
AGPCLK
(66MHz)
System Bus
400/533MHz
VGA Port
DDR
266/333MHz
ZCLK (66MHz)
82845GE
HCLK+/- (100/133MHz)
66MHz
33 MHz
3 PCI
14.318 MHz
48 MHz
BIOS
ICH4
Game Port
Floppy
LPC BUS
24 MHz
IT8712
RTL8101L(*)
LPT Port
AC97
PS/2
PCICLK
(33MHz)
CODEC
KB/Mouse
RJ45(*)
33 MHz
6 USB
ATA33/66/100
IDE Channels
Ports
COM
Ports
(2.0/1.1)
PCICLK (33MHz)
USBCLK (48MHz)
14.318 MHz
33 MHz
MCHCLK+/- (100/133MHz)
CPUCLK+/- (100/133MHz)
AGPCLK (66MHz)
GMCHCLK (66MHz)
ICH3V66 (66MHz)
CLK
GEN
24 MHz
“ * ” Only for GA-8GEM667.
- 49 -
Technical Reference
Download from Www.Somanuals.com. All Manuals Search And Download.
TM
BIOS Flash Procedureyte @BIOS Program to flash BIOS.
Method 1:
We use GA-7VTX motherboard and Flash841 BIOS flash utility as example.
Please flash the BIOS according to the following procedures if you are now under the DOS mode.
Flash BIOS Procedure:
STEP 1:
(1) Please make sure your system has installed the extraction utility such as winzip or pkunzip.
Firstly you have to install the extraction utility such as winzip or pkunzip for unzip the files.
STEP 2: Make a DOS boot diskette. (See example: Windows 98 O.S.)
Beware: Windows ME/2000 are not allowed to make a DOS boot diskette.
(1) With an available floppy disk in the floppy drive. Please leave the diskette "UN-write
protected" type. Double click the "My Computer" icon from Desktop, then click "3.5 diskette
(A)" and right click to select "Format (M)"
GA-8GEM667 Series Motherboard
- 50 -
Download from Www.Somanuals.com. All Manuals Search And Download.
(2) Select the "Quick (erase)" for Format Type, and pick both "Display summary when finished"
and "Copy system files", after that press "Start". That will format the floppy and transfer the
needed system files to it.
Beware: This procedure will erase all the prior data on that floppy, so please proceed
accordingly.
(3) After the floppy has been formatted completely, please press "Close".
- 51 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Reference
STEP 3: Download BIOS and BIOS utility program.
(2) From Support zone, click the "Motherboards BIOS & Drivers".
GA-8GEM667 Series Motherboard
- 52 -
Download from Www.Somanuals.com. All Manuals Search And Download.
(3) We use GA-7VTX motherboard as example. Please select GA-7VTX by Model or Chipset
optional menu to obtain BIOS flash files.
(4) Select an appropriate BIOS version (For example: F4), and click to download the file. It will
pop up a file download screen, then select the "Open this file from its current location" and
press "OK".
- 53 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Reference
(5) At this time the screen shows the following picture, please click "Extract" button to unzip the
files.
(6) Please extract the download files into the clean bootable floppy disk A mentioned in STEP 2,
and press "Extract".
GA-8GEM667 Series Motherboard
- 54 -
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 4: Make sure the system will boot from the floppy disk.
(1) Insert the floppy disk (contains bootable program and unzip file) into the floppy drive A. Then,
restart the system. The system will boot from the floppy disk. Please press <DEL> key to
enter BIOS setup main menu when system is boot up.
American Release:09/16/99
Megatrends AMIBIOS (C) 1999 American Megatrend
7VTX F1
Check System Health OK
AMD-Athlon(tm)Processor-900MHz
Checking NVRAM...
262144KB
Wait...
Press F1 to enter Dual BIOS Utility. Press ESC to quit
Press any key to contiune
( C ) American Megatrends Inc.,
63-0001-001199-00101111-071595-VIA_K7-GA7VTX1-F
(2) Once you enter the BIOS setup utility, the main menu will appear on the screen. Use the
arrows to highlight the item "BIOS FEATURES SETUP".
AMIBIOS SIMPLE SETUP UTILITY - VERSION 1.24b
(C) 1999 American Megatrends, Inc. All Rights Reserved
STANDARD CMOS SETUP
BIOS FEATURES SETUP
CHIPSET FEATURES SETUP
POWER MANAGEMENT SETUP
PNP / PCI CONFIGURATION
LOAD BIOS DEFAULTS
INTEGRATED PERIPHERALS
HARDWARE MONITOR & MISC SETUP
SUPERVISOR PASSWORD
USER PASSWORD
IDE HDD AUTO DETECTION
SAVE & EXIT SETUP
LOAD SETUP DEFAULTS
EXIT WITHOUT SAVING
ESC: Quit
hifg : Select Item
(Shift)F2 : Change Color
F5: Old Values
F6: Load BIOS Defaults
F7: Load Setup Defaults F10:Save & Exit
Time, Date , Hard Disk Type…
- 55 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Reference
(3) Press "Enter" to enter "BIOS FEATURES SETUP" menu. Use the arrows to highlight the item
"1st Boot Device", and then use the "Page Up" or "Page Down" keys to select "Floppy".
AMIBIOS SETUP - BIOS FEATURES SETUP
( C ) 2001 American Megatrends, Inc. All Rights Reserved
1st Boot Device
: Floppy
: IDE-0
2nd Boot Device
3rd Boot Device
: CDROM
: Disabled
: On
S.M.A.R.T. for Hard Disks
BootUp Num-Lock
Floppy Drive Seek
Password Check
ESC: Quit
F1 : Help
hifg: Select Item
: Disabled
: Setup
PU/PD/+/- : Modify
F5 : Old Values (Shift)F2: Color
F6 : Load BIOS Defaults
F7 : Load Setup Defaults
(4) Press "ESC" to go back to previous screen. Use the arrows to highlight the item "SAVE &
EXIT SETUP" then press "Enter". System will ask "SAVE to CMOS and EXIT (Y/N)?" Press
"Y" and "Enter" keys to confirm. Now the system will reboot automatically, the new BIOS
setting will be taken effect next boot-up.
AMIBIOS SIMPLE SETUP UTILITY - VERSION 1.24b
(C) 2001 American Megatrends, Inc. All Rights Reserved
STANDARD CMOS SETUP
BIOS FEATURES SETUP
INTEGRATED PERIPHERALS
HARDWARE MONITOR & MISC SETUP
SUPERVISOR PASSWORD
USER PASSWORD
CHIPSET FEATURES SETUP
POWER MANAGEMENT SETUP
Save to CMOS and EXIT (Y/N)? Y
PNP / PCI CONFIG
LOAD BIOS DEFAULTS
SAVE & EXIT SETUP
LOAD SETUP DEFAULTS
EXIT WITHOUT SAVING
ESC: Quit
hifg : Select Item
(Shift)F2 : Change Color
F5: Old Values
F6: Load BIOS Defaults
F7: Load Setup Defaults F10:Save & Exit
Save Data to CMOS & Exit SETUP
GA-8GEM667 Series Motherboard
- 56 -
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 5: BIOS flashing.
(1) After the system boot from floppy disk, type "A:\> dir/w" and press "Enter" to check the entire
files in floppy A. Then type the "BIOS flash utility" and "BIOS file" after A:\>. In this case you
have to type "A:\> Flash841 7VTX.F4" and then press "Enter".
Starting Windows 98…
Microsoft(R) Windows98
© Copyright Microsoft Corp 1981-1999
A:\> dir/w
Volume in drive A has no label
Volume Serial Number is 16EB-353D
Directory of A:\
COMMAND.COM 7VTX.F4 FLASH841.EXE
3 file(s)
0 dir(s)
838,954 bytes
324,608 bytes free
A:\> Flash841 7VTX.F4
(2) Now screen appears the following Flash Utility main menu. Press "Enter", the highlighted
item will locate on the model name of the right-upper screen. Right after that, press "Enter" to
start BIOS Flash Utility.
- 57 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Reference
(3) It will pop up a screen and asks "Are you sure to flash the BIOS?" Press [Enter] to continue
theprocedure, or press [ESC] to quit.
Beware: Please do not turn off the system while you are upgrading BIOS. It will render your
BIOS corrupted and system totally inoperative.
Are you sure to flash the BIOS?
[Enter] to continue Or [Esc] to cancel?
(4) The BIOS flash completed. Please press [ESC] to exit Flash Utility.
EXIT?
[Enter] to continue Or [Esc] to cancel?
GA-8GEM667 Series Motherboard
- 58 -
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 6: Load BIOS defaults.
Normally the system redetects all devices after BIOS has been upgraded. Therefore, we
highly recommend reloading the BIOS defaults after BIOS has been upgraded. This
important step resets everything after the flash.
(1) Take out the floppy diskette from floppy drive, and then restart the system. The boot up
screen will indicate your motherboard model and current BIOS version.
American Release:09/16/99
Megatrends AMIBIOS (C) 1999 American Megatrend
7VTX F4
Check System Health OK
AMD-Athlon(tm)Processor-900MHz
Checking NVRAM...
262144KB
Wait...
Press F1 to enter Dual BIOS Utility. Press ESC to quit
Press any key to contiune
( C ) American Megatrends Inc.,
63-0001-001199-00101111-071595-VIA_K7-GA7VTX1-F
(2) Don't forget to press <DEL> key to enter BIOS setup again when system is boot up. Use the
arrows to highlight the item "LOAD SETUP DEFAULTS" then press "Enter". System will ask
"Load Setup Defaults (Y/N)?" Press "Y" and "Enter" keys to confirm.
AMIBIOS SIMPLE SETUP UTILITY - VERSION 1.24b
(C) 2001 American Megatrends, Inc. All Rights Reserved
STANDARD CMOS SETUP
BIOS FEATURES SETUP
INTEGRATED PERIPHERALS
HARDWARE MONITOR & MISC SETUP
SUPERVISOR PASSWORD
USER PASSWORD
CHIPSET FEATURES SETUP
POWER MANAGEMENT SETUP
Load Setup Defaults? (Y/N)?N
PNP / PCI CONFIG
LOAD BIOS DEFAULTS
SAVE & EXIT SETUP
LOAD SETUP DEFAULTS
EXIT WITHOUT SAVING
ESC: Quit
hifg : Select Item
(Shift)F2 : Change Color
F5: Old Values
F6: Load BIOS Defaults
F7: Load Setup Defaults
F10:Save & Exit
Load Setup Defaults
- 59 -
Technical Reference
Download from Www.Somanuals.com. All Manuals Search And Download.
(3) Use the arrows to highlight the item "SAVE & EXIT SETUP" and press "Enter". System will
ask "SAVE to CMOS and EXIT (Y/N)?" Press "Y" and "Enter" keys to confirm. Now the
system will reboot automatically, the new BIOS setting will be taken effect next boot-up.
AMIBIOS SIMPLE SETUP UTILITY - VERSION 1.24b
(C) 2001 American Megatrends, Inc. All Rights Reserved
STANDARD CMOS SETUP
BIOS FEATURES SETUP
INTEGRATED PERIPHERALS
HARDWARE MONITOR & MISC SETUP
SUPERVISOR PASSWORD
USER PASSWORD
CHIPSET FEATURES SETUP
POWER MANAGEMENT SETUP
Save to CMOS and EXIT (Y/N)? Y
PNP / PCI CONFIG
LOAD BIOS DEFAULTS
SAVE & EXIT SETUP
LOAD SETUP DEFAULTS
EXIT WITHOUT SAVING
ESC: Quit
hifg : Select Item
(Shift)F2 : Change Color
F5: Old Values
F6: Load BIOS Defaults
F7: Load Setup Defaults F10:Save & Exit
Save Data to CMOS & Exit SETUP
(4) Congratulate you have accomplished the BIOS flash procedure.
GA-8GEM667 Series Motherboard
- 60 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Method 2:
Q-Flash Introduction
A. What is Q-Flash Utility?
Q-Flash utility is a pre-O.S. BIOS flash utility enables users to update its BIOS within BIOS
mode, no more fooling around any OS.
B. How to use Q-Flash?
a. After power on the computer, pressing <Del> immediately during POST (Power On Self Test) it
will allow you to enter AWARD BIOS CMOS SETUP, then press <F8> to enter Q-Flash utility.
CMOS Setup Utility-Copyright (C) 1984-2002 Award Software
}Standard CMOS Features
}Advanced BIOS Features
}Integrated Peripherals
Top Performance
Load Fail-Safe Defaults
Load Optimized Defaults
Save & Exit Setup
}Power
Enter Q-Flash Utility (Y/N)? Y
}PnP/PC
}PC Health Status
}Frequency/Voltage Control
ESC:Quit
Exit Without Saving
higf:Select Item
F10:Save & Exit Setup
F8: Q-Flash
Time, Date, Hard Disk Type...
b. Q-Flash Utility
Q-Flash Utility V3.05
SST 39SF020 / 256K
Yes
Flash Type/Size :
Keep DMI Data :
Load BIOS from Floppy
Save BIOS to Floppy
Space Bar:Change Value
ESC: Reset
Enter: Run
!/": Select Item
- 61 -
Technical Reference
Download from Www.Somanuals.com. All Manuals Search And Download.
Load BIOS From Floppy
!In the A:drive, insert the "BIOS" diskette, then Press Enter to Run.
1 File(s) found
XXXX.XX
256K
Total Size: 1.39M
F5: Refresh
Free Size: 1.14M
ESC: Return Main
DEL: Delete
Where XXXX.XX is name of the BIOS file.
!Press Enter to Run.
Are you sure to update BIOS?
[Enter] to contiune Or [ESC] ot abort...
!Press Enter to Run.
!! COPY BIOS Completed -Pass !!
Please press any key to continue
Congratulation! You have completed the flashed and now can restart system.
GA-8GEM667 Series Motherboard
- 62 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Method 3:
TM
If you don’t have DOS boot disk, we recommend that you used Gigabyte @BIOS program to
flash BIOS.
2.Click "@BIOS Writer Utility
Press "Tools" icon.
v.1.08q".
1.Click "Gigabyte Utilities".
(2)
(1)
Click here.
Click "!".
3. Please select @BIOS sever site,
then Click "OK".
(3)
(4)
Methods and steps:
I. Update BIOS through Internet
a. Click "Internet Update" icon
b. Click "Update New BIOS" icon
TM
c. Select @BIOS sever
d. Select the exact model name on your motherboard
e. System will automatically download and update the BIOS.
- 63 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Reference
II. Update BIOS NOT through Internet:
a. Do not click "Internet Update" icon
b. Click "Update New BIOS"
c. Please select "All Files" in dialog box while opening the old file.
d. Please search for BIOS unzip file, downloading from internet or any other methods (such
as: 8GEM667.E2).
e. Complete update process following the instruction.
III. Save BIOS
In the very beginning, there is "Save Current BIOS" icon shown in dialog box. It means to
save the current BIOS version.
IV. Check out supported motherboard and Flash ROM:
In the very beginning, there is "About this program" icon shown in dialog box. It can help you
check out which kind of motherboard and which brand of Flash ROM are supported.
Note:
a. In method I, if it shows two or more motherboard's model names to be selected, please
make sure your motherboard's model name again. Selecting wrong model name will
cause the system unbooted.
b. In method II, be sure that motherboard's model name in BIOS unzip file are the same as
your motherboard's. Otherwise, your system won't boot.
TM
c. In method I, if the BIOS file you need cannot be found in @BIOS server, please go onto
Gigabyte's web site for downloading and updating it according to method II.
d. Please note that any interruption during updating will cause system unbooted
GA-8GEM667 Series Motherboard
- 64 -
Download from Www.Somanuals.com. All Manuals Search And Download.
@ BIOS Introduction
Gigabyte announces @ BIOS
Windows BIOS live update utility
Have you ever updated BIOS by yourself? Or like
many other people, you just know what BIOS is,
but always hesitate to update it? Because you
think updating newest BIOS is unnecessary and
actually you don’t know how to update it.
Maybe not like others, you are very experienced in BIOS updating and spend quite a lot of
time to do it. But of course you don’t like to do it too much. First, download different BIOS from
website and then switch the operating system to DOS mode. Secondly, use different flash utility to
update BIOS. The above process is not a interesting job. Besides, always be carefully to store the
BIOS source code correctly in your disks as if you update the wrong BIOS, it will be a nightmare.
Certainly, you wonder why motherboard vendors could not just do something right to save
your time and effort and save you from the lousy BIOS updating work? Here it comes! Now
Gigabyte announces @BIOS—the first Windows BIOS live update utility. This is a smart BIOS
update software. It could help you to download the BIOS from internetand update it. Not like the
other BIOS update software, it’s a Windows utility. With the help of “@BIOS’, BIOS updating is no
more than a click.
Besides, no matter which mainboard you are using, if it’s a Gigabyte’s product*, @BIOS help
you to maintain the BIOS. This utility could detect your correct mainboard model and help you to
choose the BIOS accordingly. It then downloads the BIOS from the nearest Gigabyte ftp site
automatically. There are several different choices; you could use “Internet Update” to download
and update your BIOS directly. Or you may want to keep a backup for your current BIOS, just
choose “Save Current BIOS” to save it first. You make a wise choice to use Gigabyte, and @BIOS
update your BIOS smartly. You are now worry free from updating wrong BIOS, and capable to
maintain and manage your BIOS easily. Again, Gigabyte’s innovative product erects a milestone
in mainboard industries.
For such a wonderful software, how much it costs? Impossible! It’s free! Now, if you buy a
Gigabyte’s motherboard, you could find this amazing software in the attached driver CD. But
please remember, connected to internet at first, then you could have a internet BIOS update from
your Gigabyte @BIOS.
- 65 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Reference
Easy TuneTM 4 Introduction
Gigabyte announces EasyTuneTM 4 Windows based Overclocking utility
EasyTune 4 carries on the heritage so as to pave the way for future generations.
Overclock" might be one of the most common issues in computer field. But have many users ever
tried it? The answer is probably "no". Because
"Overclock" is thought to be very difficult and in-
cludes a lot of technical know-how, sometimes
"Overclock" is even considered as special skills
found only in some enthusiasts. But as to the ex-
perts in "Overclock", what's the truth? They may
spend quite a lot of time and money to study, try
and use many different hardware or BIOS tools to
do "Overclock". And even with these technologies,
they still learn that it's quite a risk because the safety
and stability of an "Overclock" system is unknown. Now everything is different because of a Win-
dows based overclocking utility "EasyTune 4" --announced by Gigabyte. This windows based utility
has totally changed the gaming rule of "Overclock". This is the first windows based overclocking
utility is suitable for both normal and power users. Users can choose either "Easy Mode" or "Ad-
vanced Mode" for overclocking at their convenience. For users who choose "Easy Mode", they just
need to click "Auto Optimize" to have autoed and immediate CPU overclocking. This software will
then overdrive CPU speed automatically with the result being shown in the control panel. If users
prefer "Overclock" by them, there is also another choice. Click "Advanced Mode" to enjoy "sport
drive" class Overclocking user interface. "Advanced Mode", allows users to change the system bus
/AGP / Memory working frequency in small increments to get ultimate system performance. It oper-
ates in coordination with Gigabyte motherboards. Besides, it is different from other traditional over-
clocking methods, EasyTune 4 doesn't require users to change neither BIOS nor hardware switch/
jumper setting; on the other hand, they can do "Overclock" at easy step . Therefore, this is a safer
way for "Overclock" as nothing is changed on software or hardware. If user runs EasyTune 4 over
system's limitation, the biggest lost is only to restart the computer again and the side effect is then
well controlled. Moreover, if one well-performed system speed has been tested in EasyTune 4, user
can "Save" this setting and "Load" it in next time. Obviously, Gigabyte EasyTune 4 has already
turned the "Overclock" technology toward to a newer generation. This wonderful software is now
free bundled in Gigabyte motherboard attached in driver CD. Users may make a test drive of
"EasyTune 4" to find out more amazing features by themselves.
*Some Gigabyte products are not fully supported by EasyTune 4. Please find the products sup-
ported list in the web site.
*Any "Overclocking action" is at user's risk, Gigabyte Technology will not be responsible for any
damage or instability to your processor, motherboard, or any other components.
GA-8GEM667 Series Motherboard
- 66 -
Download from Www.Somanuals.com. All Manuals Search And Download.
2-/4-/6-Channel Audio Function
The installation of windows 98SE/2K/ME/XP is very simple. Please follow next step to install the
Introduction
function!
Stereo Speakers Connection and Settings:
We recommend that you use the speaker with amplifier to acquire the best sound effect if the stereo output is
applied.
STEP 1:
Connect the stereo speakers or earphone to “Line Out”.
Line Out
STEP 2 :
After installation of the audio driver, you ‘ll find an
icon on the taskbar’s status area. Click the audio icon
“Sound Effect” from the windows tray at the bottom of
the screen.
STEP 3:
Select “Speaker Configuration”, and choose the
“2 channels for stereo speakers out put”.
- 67 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Reference
4 Channel Analog Audio Output Mode
STEP 1 :
Connect the front channels to “Line Out”,the rear
channels to “Line In”.
Line Out
Line In
STEP 2 :
After installation of the audio driver, you ‘ll find an
icon on the taskbar’s status area. Click the audio icon
“Sound Effect” from the windows tray at the bottom of
the screen.
STEP 3 :
Select “Speaker Configuration”, and choose the “4
channels for 4 speakers out put”.
Disable “Only SURROUND-KIT”, and press “OK”.
When the “Environment settings” is “None”, the
sound would be performed as stereo mode
(2 channels output). Please select the other settings
for 4 channels output.
GA-8GEM667 Series Motherboard
- 68 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic 6 Channel Analog Audio Output Mode
Use the back audio panel to connect the audio output
without any additional module.
STEP 1 :
Line Out
Line In
MIC In
Connect the front channels to “Line Out”,the rear chan-
nels to “Line In”, and the Center/Subwoofer channels
to “MIC In ”.
STEP 2 :
After installation of the audio driver, you ‘ll find an
icon on the taskbar’s status area. Click the audio icon
“Sound Effect” from the windows tray at the bottom of
the screen.
STEP 3 :
Select “Speaker Configuration”, and choose the
“6 channels for 5.1 speakers out put”.
Disable “Only SURROUND-KIT” and pess “OK”
- 69 -
Technical Reference
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced 6 ChannelAnalog Audio Output Mode (usingAudio Combo Kit,Optional Device):
(Audio Combo Kit provides SPDIF output port : optical & coaxis and SURROUND-KIT : Rear R/L &
Center/subwoofer)
SURROUND-KIT access analog output to rear
channels and Center/Subwoofer channels. It is the best
solution if you need 6 channel output, Line In and MIC
at the same time. "SURROUND-KIT" is included in the
GIGABYTE unique "Audio Combo Kit" as picture.
STEP 1 :
Insert the “Audio Combo Kit” in the back of the case ,
and fix it with the screw.
STEP 2 :
Connect the ”SURROUND-KIT” to SUR_CEN on the
M/B.
GA-8GEM667 Series Motherboard
- 70 -
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 3 :
Connect the front channels to back audio panel’s
“Line Out”, the rear channels to SURROUND-KIT’s
REAR R/L, and the Center/Subwoofer channels to
SURROUND-KIT’s SUB CENTER.
STEP 4 :
Click the audio icon "Sound Effect" from the windows
tray at the bottom of the screen.
STEP 5 :
Select "Speaker Configuration", and choose the "6
channels for 5.1 speakers out put".
Enable "Only SURROUND-KIT" and press "OK".
Basic & Advanced 6 Channel Analog Audio Output ModeNotes:
When the "Environment settings" is "None", the sound
would be performed as stereo mode(2 channels
output). Please select the other settings for 6 channels
output.
- 71 -
Technical Reference
Download from Www.Somanuals.com. All Manuals Search And Download.
SPDIF Output Device (Optional Device)
A “SPDIF output” device is available on the
motherboard. Cable with rear bracket is provided
and could link to the “SPDIF output” connector
(As picture.) For the further linkage to decoder,
rear bracket provides coaxial cable and Fiber
connecting port.
1. Connect the SPDIF output device to the rear
bracket of PC, and fix it with screw.
2. Connect SPDIF wire to the motherboard.
3. Connect co-axial or optical output to the SPDIF
decoder.
GA-8GEM667 Series Motherboard
- 72 -
Download from Www.Somanuals.com. All Manuals Search And Download.
- 73 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Reference
GA-8GEM667 Series Motherboard
- 74 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 Appendix
Picture below are shown in Windows XP (CD driver version 1.0)
Appendix A: Chipset Driver Installation
A. Intel Chipset Software Installation Utility:
Insert the driver CD-title that came with your motherboard into your CD-ROM driver, the driver
CD-title will auto start and show the installation guide. If not, please double click the CD-ROM device
icon in "My computer", and execute the setup.exe.
1.Click "Intel Chipset Software Installation
Utility" item.
(1)
(2)
3.Click "Yes".
(4)
2.Click "Next".
(3)
- 75 -
Appendix
Download from Www.Somanuals.com. All Manuals Search And Download.
4Click "Next".
(5)
(6)
5.Click "Finish" to restart computer.
(7)
GA-8GEM667 Series Motherboard
- 76 -
Download from Www.Somanuals.com. All Manuals Search And Download.
B. Intel Application Accelerator
Insert the driver CD-title that came with your motherboard into your CD-ROM driver, the driver
CD-title will auto start and show the installation guide. If not, please double click the CD-ROM device
icon in "My computer", and execute the setup.exe.
1.Click "Intel Application Accelerator" item.
(2)
(1)
3.Click "Yes".
(4)
2.Click "Next".
(3)
5.Click "Next".
(6)
4.Click "Next".
(5)
- 77 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
6.Click "Finish" to restart computer.
(8)
(7)
C. Intel 845GE/GV ChipSet VGA Graphics Driver
1.Click "Intel 845GE/GV
ChipSet VGA Graphics Driver"
item.
2.Click "Next".
(2)
(1)
4.Click "Finish" to restart computer.
(4)
3.Click "Yes".
(3)
d. USB Patch Driver For XP
Enable S3 for USB Device Setup is preparing the InstallShield(R) Wizard which will guide you
through thesetupprocess.
GA-8GEM667 Series Motherboard
- 78 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B: RealTek AC’97 Audio Driver
Revision History
Insert the driver CD-title that came with your motherboard into your CD-ROM driver, the driver
CD-title will auto start and show the installation guide. If not, please double click the CD-ROM device
icon in "My computer", and execute the setup.exe.
Press "Audio Driver" icon.
1.Click "Install RealTekAC’97 Driver"
item.
(1)
2.Click "Next".
(2)
3.Click "Finish" to restart computer.
(3)
(4)
- 79 -
Appendix
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C: Intel Network Driver Installation (*)
Press "Network Driver"
icon.
2.Click "Next".
1.Click "Install Intel Netware
Driver(XP)".
(2)
(1)
4.Click "Install".
(4)
3.Click "Next".
(3)
5.Click "Finish" to restart computer.
(6)
(5)
“ * ” Only for GA-8GEM667.
GA-8GEM667 Series Motherboard
- 80 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix D: USB 2.0 Driver Installation
A. USB 2.0 Driver Patch For XP:
Insert the driver CD-title that came with your motherboard into your CD-ROM driver, the driver
CD-title will auto start and show the installation guide. If not, please double click the CD-ROM device
icon in "My computer", and execute the setup.exe.
Press "USB 2.0 Driver" icon.
2.Click "Next".
1.Click "MS USB 2.0 Driver Patch For XP" .
(2)
(1)
3.Click "Finish".
(4)
(3)
- 81 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
B. USB 2.0 Driver For ICH4:
Insert the driver CD-title that came with your motherboard into your CD-ROM driver, the driver
CD-title will auto start and show the installation guide. If not, please double click the CD-ROM device
icon in "My computer", and execute the setup.exe.
Press "USB 2.0 Driver" icon.
1.Click "USB 2.0 Driver For ICH4" .
(1)
2.Click "Next".
(2)
3.Click "Finish" to restart computer.
(3)
If there is any problem occurred during USB2.0 device installing, using or upgrading. Please
visit Microsoft or GIGABYTE website for downloading the latest drivers.
GA-8GEM667 Series Motherboard
- 82 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix E: EasyTune 4 Utilities Installation
Revision History
Insert the driver CD-title that came with your motherboard into your CD-ROM driver, the driver
CD-title will auto start and show the installation guide. If not, please double click the CD-ROM device
icon in "My computer", and execute the setup.exe.
Press "Software Utilities" icon.
2.Click "Easy Tune 4".
1.Click "Install GIGABYTE Utilities" item.
(2)
(1)
3.Click "Next".
4.Click "Next".
(4)
(3)
5.Click "Finish" to restart computer.
(6)
(5)
- 83 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Appendix F: Acronyms
Acronyms
ACPI
APM
AGP
AMR
ACR
BIOS
CPU
CMOS
CRIMM
CNR
DMA
DMI
Meaning
AdvancedConfigurationandPowerInterface
Advanced Power Management
AcceleratedGraphicsPort
Audio Modem Riser
Advanced Communications Riser
Basic Input / Output System
Central Processing Unit
Complementary Metal Oxide Semiconductor
Continuity RIMM
Communication and Networking Riser
Direct Memory Access
DesktopManagementInterface
Dual Inline Memory Module
DualRetentionMechanism
Dynamic Random Access Memory
DoubleDataRate
DIMM
DRM
DRAM
DDR
ECP
ESCD
ECC
EMC
EPP
ExtendedCapabilitiesPort
ExtendedSystemConfigurationData
Error Checking and Correcting
ElectromagneticCompatibility
EnhancedParallelPort
ESD
ElectrostaticDischarge
FDD
Floppy Disk Device
FSB
Front Side Bus
HDD
IDE
Hard Disk Device
IntegratedDualChannelEnhanced
InterruptRequest
IRQ
I/O
Input/Output
IOAPIC
ISA
InputOutputAdvancedProgrammableInputController
IndustryStandardArchitecture
Local Area Network
LAN
to be continued......
GA-8GEM667 Series Motherboard
- 84 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Acronyms
LBA
Meaning
Logical Block Addressing
LightEmittingDiode
LED
MHz
MIDI
MTH
MPT
NIC
Megahertz
MusicalInterfaceDigitalInterface
Memory Translator Hub
MemoryProtocolTranslator
Network Interface Card
OperatingSystem
OS
OEM
PAC
POST
PCI
OriginalEquipmentManufacturer
PCI A.G.P. Controller
Power-On Self Test
PeripheralComponentInterconnect
Rambus in-line Memory Module
SpecialCircumstanceInstructions
Single Edge Contact Cartridge
Static Random Access Memory
Symmetric Multi-Processing
SystemManagementInterrupt
Universal Serial Bus
RIMM
SCI
SECC
SRAM
SMP
SMI
USB
VID
VoltageID
- 85 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
Technical Support/RMA Sheet
Customer/Country:
Company:
E-mail Add. :
Phone No.:
ContactPerson:
Model name/Lot Number:
BIOS version:
PCB revision:
Driver/Utility:
O.S./A.S.:
Modelname
Hardware
Configuration
CPU
Mfs.
Size:
Memory
Brand
Video Card
Audio Card
HDD
CD-ROM /
DVD-ROM
Modem
Network
AMR / CNR
Keyboard
Mouse
Power supply
Other Device
ProblemDescription:
GA-8GEM667 Series Motherboard
- 86 -
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Eclipse Fujitsu Ten Car Stereo System AVN 30D User Manual
Extron electronic Switch FOX T USW 103 User Manual
Faber Indoor Fireplace SP4 User Manual
Fellowes Paper Shredder P 40 User Manual
Fluke Modem 2635A RF900USB User Manual
Garland Double Oven MST47R User Manual
GE Convection Oven 164D3333P095 User Manual
GENNUM Headphones nXZEN User Manual
GE Refrigerator 200D8074P036 User Manual
Global Upholstery Co Patio Furniture 3371CRTL User Manual