Genesis ICE Cordless Drill GCD18BK User Manual

18V Cordless Drill/Driver  
Perceuse / Tournevis sans fil de 18v  
Taladro / Tornillador inalámbrico de 18v  
Operator’s Manual  
Manuel d’utilisation  
Manual del Operario  
GCD18BK  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WARNING: READ AND UNDERSTAND ALL WARNINGS, CAUTIONS  
AND OPERATING INSTRUCTIONS BEFORE USING THIS EQUIPMENT. Failure  
to follow all instructions listed below may result in electric shock, fire and/or  
serious personal injury.  
SAVE THESE INSTRUCTIONS  
WORK AREA SAFETY:  
Keep your work area clean and well lit. Cluttered benches and dark areas invite  
accidents.  
Do not operate power tools in explosive atmospheres, such as in the  
presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust  
or fumes.  
Keep bystanders, children, and visitors away while operating a power  
tool. Distractions can cause you to lose control.  
ELECTRICAL SAFETY  
Power tool plugs must match the outlet. Never modify the plug in any way. Do not  
use any adapter plugs in any earthed (grounded) power tools. Double insulated tools are equipped  
with a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only  
one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact  
a qualified electrician to install a polarized outlet. Do not change the plug in any way. Double  
insulation eliminates the need for the three wire grounded power cord and grounded power supply  
system.  
• Do not expose power tools to rain or wet conditions. Water entering a power  
tool will increase the risk of electric shock.  
• Avoid body contact with earthed or grounded surfaces such as pipes,  
radiators, ranges and refrigerators. There is an increased risk of electric shock if  
your body is grounded.  
• Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power  
tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged cords increase the risk  
of electric shock.  
• When operating a power tool outside, use an extension cord suitable  
for outdoor use. These cords are rated for outdoor use and reduce the risk of electric shock.  
• Do not use AC only rated tools with a DC power supply. While the tool may  
appear to work. The electrical components of the AC rated tool are likely to fail and rate a hazard to  
the operator.  
PERSONAL SAFETY  
Stay alert, watch what you are doing and use common sense when operating a power tool.  
Do not use tool while tired or under the influence of drugs, alcohol, or medication. A moment of  
inattention while operating power tools may result in serious personal injury.  
• Use safety equipment. Always wear eye protection. Safety equipment such as dust  
mask, non-skid safety shoes, hard hat, or hearing protection for appropriate conditions will reduce  
personal injuries.  
• Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves  
away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts. Air  
vents may cover moving parts and should be avoided.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3
• Avoid accidental starting. Ensure the switch is in the off position before plugging in.  
Carrying power tool with your finger on the switch or plugging in power tools that have the switch  
on invites accidents.  
• Remove any adjusting keys or wrenches before turning the power  
tool on. A wrench or key that is left attached to a rotating part of the tool may result in personal  
injury.  
• Do not overreach. Maintain proper footing and balance at all times. Loss of balance can  
cause an injury in an unexpected situation.  
• If devices are provided for connection of dust extraction and  
collection facilities, ensure these are connected and properly used.  
Use of these devices can reduce dust related hazards.  
• Do not use a ladder or unstable support. Stable footing on a solid surface enables  
better control of the tool in unexpected situations.  
• Keep tool handles dry, clean and free from oil and grease. Slippery handles  
cannot safely control the tool.  
TOOL USE AND CARE  
Secure the work piece. Use clamp or other practical way to hold the work piece to a  
stable platform. Holding the work piece by hand or against your body is unstable and may lead to  
loss of control.  
• Do not force the power tool. The tool will perform the job better and safer at the feed  
rate for which it is designed. Forcing the tool could possibly damage the tool and may result in  
personal injury.  
• Use the correct power tool for the job. Don’t force the tool or attachment to do a  
job for which it is not designed.  
• Do not use tool if switch does not turn it on or off. Any tool that cannot be  
controlled with the switch is dangerous and must be repaired or replaced by an authorized service  
center.  
Turn power tool off, and disconnect the plug from the power source and/or  
battery pack from the power tool before making any adjustments, changing the accessories, or  
storing the tools. Such preventive safety measures reduce the risk of an accidental start up which  
may cause personal injury.  
• Store idle tool out of reach of children and other inexperienced  
persons. It is dangerous in the hand of untrained users.  
• Maintain power tools with care. Check for proper alignment and binding of moving  
parts, component breaks, and any other conditions that may affect the tool’s operation. A guard  
or any other part that is damaged must be properly repaired or replaced by an authorized service  
center to avoid risk of personal injury.  
• Use recommended accessories. Using accessories and attachments not  
recommended by the manufacturer or intended for use on this type tool may cause damage to  
the tool or result in personal injury to the user. Consult the operator’s manual for recommended  
accessories.  
• Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp  
cutting edges are less likely to bind and are easier to control.  
18V Cordless Drill/Driver  
Operator’s Manual  
Download from Www.Somanuals.com. All ManualGs SCeDarc1h8ABnKd Download.  
• Feed the work piece in the correct direction and speed. Feed the work  
piece into a blade, cutter, or abrasive surface against the direction of the cutting tool’s direction  
of rotation only. Incorrectly feeding the work piece in the same direction may cause the work  
piece to be thrown out at high speed.  
• Never leave the tool running unattended, turn the power off. Do not  
leave the tool until it comes to a complete stop.  
• Never start the power tool when any rotating component is in  
contact with the work piece.  
BATTERY TOOL USE AND CARE  
Ensure the switch trigger is in the off position before inserting  
battery pack. Inserting the battery pack into power tools that have the switch on invites  
accidents.  
Recharge only with the charger specified by the manufacturer. A  
charger that is suitable for one type of battery pack may create a risk of fire when used with  
another battery pack.  
Use battery tools only with specified battery pack. Use of any other battery  
packs may create a risk of injury and fire.  
Avoid storing battery pack in a container with other metal objects  
such as nails, coins, clips, keys, screws, or other small metal objects that can make a  
connection from one terminal to another. Always protect the battery terminals when battery  
pack is not being used. Connecting the battery terminals together may cause burns or a fire.  
Under abusive conditions, liquid may be ejected from the battery.  
Avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally  
seek medical help. Liquid ejected from the battery may cause irritation or burns.  
Battery tools do not need to be plugged into an electrical outlet,  
therefore, they are always in operation condition. Be aware of possible hazards when not using  
your battery tool or when changing accessories. Following this rule will reduce the risk of  
electric shock, fire or personal injury.  
WARNING:  
USE OF THIS TOOL CAN GENERATE AND DISBURSE DUST OR OTHER  
AIRBORNE PARTICLES, INCLUDING WOOD DUST, CRYSTALLINE SILICA DUST  
AND ASBESTOS. Direct particles away from face and body. Always operate  
tool in a well-ventilated area and provide for proper dust removal. Use dust  
collection system wherever possible. Exposure to the dust may cause serious  
and permanent respiratory or other injury, including silicosis (a serious lung  
disease), cancer, and death. Avoid breathing the dust, and avoid prolonged  
contact with the dust. Allowing dust to get into your mouth or eyes, or lay on  
your skin may promote absorption of harmful material. Always use properly  
fitting NIOSH/OSHA approved respiratory protection appropriate for dust  
exposure, and wash exposed areas with soap and water.  
SERVICE  
Have your power tool Serviced by a qualified repair person using  
only identical replacement parts. This will ensure that the safety of the power tool  
is maintained.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5
WARNING: READ AND UNDERSTAND ALL WARNINGS, CAUTIONS  
AND OPERATING INSTRUCTIONS BEFORE USING THIS EQUIPMENT. Failure  
to follow all instructions listed below may result in electric shock, fire and/or  
serious personal injury.  
SAVE THESE INSTRUCTIONS  
EXTENSION CORDS  
Grounded tools require a three wire extension cord. Double insulated tools can  
use either a two or three wire extension cord. As the distance from the power supply outlet increases,  
you must use a heavier gauge extension cord. Using extension cords with inadequately sized wire  
causes a serious drop in voltage, resulting in loss of power and possible tool damage. Refer to the  
table shown below to determine the required minimum wire size.  
The smaller the gauge number of the wire, the greater the capacity of the cord. For example: a 14-  
gauge cord can carry a higher current than a 16-gauge cord. When using more than one extension  
cord to make up the total length, be sure each cord contains at least the minimum wire size required.  
If you are using one extension cord for more than one tool, add the nameplate amperes and use the  
sum to determine the required minimum wire size.  
Guidelines for Using Extension Cords  
• If you are using an extension cord outdoors, be sure it is marked with the suffix “W-A” (“W” in  
Canada) to indicate that it is acceptable for outdoor use.  
• Be sure your extension cord is properly wired and in good electrical condition. Always replace a  
damaged extension cord or have it repaired by a qualified person before using it.  
• Protect your extension cords from sharp objects, excessive heat, and damp or wet areas.  
Recommended Minimum Wire Gauge for Extension Cords (120 Volt)  
Nameplate  
Amperes  
(At Full Load)  
Extension Cord Length  
25 Feet  
50 Feet  
75 Feet  
100 Feet  
150 Feet  
200 Feet  
0–2.0  
2.1–3.4  
18  
18  
18  
18  
18  
14  
12  
18  
18  
18  
16  
14  
12  
10  
18  
18  
16  
14  
12  
10  
8
18  
16  
14  
12  
10  
10  
8
16  
14  
12  
12  
8
16  
14  
12  
10  
8
3.5–5.0  
5.1–7.0  
7.1–12.0  
12.1–16.0  
16.1–20.0  
8
6
6
6
SPECIFIC SAFETY RULES FOR CORDLESS DRILL/DRIVER  
WARNING: DO NOT LET COMFORT OR FAMILIARITY WITH PRODUCT  
(GAINED FROM REPEATED USE) REPLACE STRICT ADHERENCE TO  
PRODUCT SAFETY RULES. If you use this tool unsafe or incorrectly, you can  
suffer serious personal injury!  
Hold the tool by insulated gripping surfaces when performing an operation  
where the tool may contact hidden wiring. Contact with a “live” wire will make exposed metal  
parts of the tool “live” and shock the operator.  
Do not leave the tool running. Operate the tool only when hand-held.  
Be Aware that this tool is always in an operating condition because it  
does not have to be plugged into an electric outlet.  
,
18V Cordless Drill/Driver  
Operator’s Manual  
Download from Www.Somanuals.com. All ManualGs SCeDarc1h8ABnKd Download.  
When operating the tool from an elevated position be aware of people or  
,
things beneath you.  
Always hold the tool firmly in your hands before switching the tool  
“ON”  
.
The reaction to the torque of the motor as it accelerates to full speed may cause the tool  
to twist  
.
Wear eye and hearing protection. Always use safety glasses with side shields.  
Unless otherwise specified, everyday glasses provide only limited impact resistance, they are not  
safety glasses. Use only certified safety equipment; eye protection equipment should comply with  
ANSI z87.1 standards. Protective hearing equipment should comply with ANSI s3.19 standards.  
Protect your lungs. Wear a face or dust mask if the operation is dusty. Following this rule  
will reduce the risk of personal injury.  
Always disconnect battery pack from tool or place the switch in the locked  
or off position before any assembly, adjustments or changing of accessories. Following this  
instruction will reduce the risk of serious personal injury.  
Do not place battery tools or their batteries near fire or heat. This will  
reduce the risk of explosion and possibly personal injury.  
Never use a battery which has been dropped or received a sharp  
blow. A damaged battery is subject to explosion. Properly dispose of a dropped or damaged  
battery immediately.  
Use designated battery pack (Genesis™ -Model GAB18B) and  
charger (Genesis™- Model GAC240400-SH) for this tool Use of any other  
.
batteries may result in a risk of fire.  
WARNING: Read and understand safety and operating instructions  
of designated battery and charger before using this tool. This manual  
contains important safety and operating instruction for battery charger.  
SAVE THESE INSTRUCTIONS  
IMPORTANT SAFETY INSTRUCTIONS FOR CHARGER &  
BATTERY  
• Save These Instructions. This manual contains important safety and operating  
instructions for your battery charger.  
• Before Using the battery Charger, read all instructions and cautionary markings on (1)  
Battery Charger, (2) Battery , and (3) Product using battery.  
• Use only the charger which accompanied your product or direct replacements as listed in  
this manual. Do not substitute any other charger.  
• Do not recharge battery in damp or wet environments. Do not expose battery  
pack to water or rain.  
• Do not operate charger with damaged cord or plug. Replace immediately.  
• Do not operate charger if it has received a sharp blow, been dropped or  
otherwise damaged in any way. Take it to a qualified serviceman.  
• Do not disassemble charger or battery pack. Take it to a qualified serviceman  
when service or repair is required. Incorrect reassembly may result in a risk of electric shock or fire.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7
• Do not charge battery pack when temperature is below 50 degrees F (10 degrees  
C) or above 104 degrees F (40 degrees C). Store tool and battery pack in a location where  
temperature will not exceed 122 degrees F (50 degree C). This is important to prevent serious  
damage to the battery cells.  
• Place charger on flat non-flammable surface and away from flammable  
materials when re-charging the battery pack.  
To reduce risk of electric shock, unplug charger from outlet before attempting any  
maintenance or cleaning.  
• If operating time has become excessively shorter, stop operating  
immediately. It may result in a risk of overheating, possible burns and even an explosion.  
• Battery leakage may occur under extreme usage or temperature conditions. Avoid  
contact with skin and eyes. If liquid comes in contact with your skin, wash immediately with soap  
and water. If liquid gets into your eyes, wash them out with clear water for at least 10 minutes, and  
then seek medical attention right away.  
• Do not attempt to use a step-up transformer, an engine generator or DC power  
receptacle.  
• Do not short the battery pack. Do not touch the terminal with any conductive material.  
Avoid storing battery pack in a container with other metal objects such as nails, coins, etc. Always  
protect the battery terminals when battery pack is not used.  
• Do not charge battery pack inside a box or container of any kind. The  
battery must be placed in a well ventilated area during charging.  
• Do not allow anything to cover or clog the charger vents.  
• Do not incinerate the battery pack even if it is severely damaged or is completely  
worn out. The battery pack can explode in a fire.  
• Disconnect Charger from the power source when not in use. This will  
reduce the risk to electric shock or damage to the charger if metal pieces should fall into the  
opening. It also will help prevent damage to the charger during a power surge.  
WARNING: A battery short can cause a large current flow, overheating,  
possible burns and even a breakdown.  
WARNING: 120 volts are present at charging terminals, do not probe  
with conductive objects. Electric shock or electrocution may result. Do not  
allow any liquid to get inside charger. Electric shock may result.  
WARNING: This product comes with the battery installed internally. You  
are not allowed to install or remove the battery from the product.  
IMPORTANT BATTERY INFORMATION: DISPOSING THE  
BATTERY PACK  
• Your batteries are Nickel-Cadmium rechargeable batteries. Certain Local, State and  
Federal laws prohibit disposal of these batteries in ordinary trash.  
• Consult your local waste authorities for your disposal/recycling options.  
• More information regarding battery disposal in U.S. and Canada is available at;  
18V Cordless Drill/Driver  
Operator’s Manual  
Download from Www.Somanuals.com. All ManualGs SCeDarc1h8ABnKd Download.  
YOUR CORDLESS DRILL/DRIVER  
2
1
3
4
5
6
FIG 1  
7
8
1. Keyless Chuck  
2. Torque Ring  
3. Bubble Level  
4. LED Work Light  
5. Trigger Switch  
6. Reversing Switch  
7. Magnetic Tray  
8. Battery Pack  
UNPACKING AND CONTENT  
IMPORTANT: Due to modern mass production techniques, it is  
unlikely the tool is faulty or that a part is missing. If you find anything  
wrong, do not operate the tool until the parts have been replaced or the  
fault has been rectified. Failure to do so could result in serious personal  
injury.  
Contents in Package:  
Description  
Drill/Driver  
Wall Adaptor  
13-Piece Bit set  
QTY  
Description  
Charger Stand  
Case  
QTY  
1
1
1
1
1
1
Operator’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9
OPERATION  
WARNING: To reduce the risk of serious personal injuries, read and  
follow all important safety warning and instructions before using this  
tool.  
NOTE: Always Check that the power supply corresponds to the voltage  
on the ratings plate.  
Charging the tool (FIG 2)  
• Use only the Battery Charger that is included in this kit to recharge your batteries.  
• Use only 120 Volt AC Power Source.  
• Charge your batteries fully before using the drill for the first time.  
Connect the wall adaptor (2) to charger stand (3)  
• Plug the wall adaptor (1) into a 120 Volt AC Power Source.  
3
The red light on the charger will illuminate, indicating the  
charger is power on.  
• Insert the battery (1) into the slot on the charger stand  
(3). Make sure that the battery is seated firmly in the  
charger. The green light on the charger will illuminate,  
indicating that the battery is charging.  
• Charge for 3 hours before initial use, and after normal  
use. If drill has been used continuously, and the battery  
is completely discharged, it may require up to 5 hours to  
fully recharge the battery.  
2
1
FIG 2  
• The green and red lights will remain lit, even after charging is complete.  
• Batteries may become warm while charging. This is normal.  
• If battery is hot after continuous use in the drill, allow it to cool down to room temperature before  
charging. This will extend the life of your batteries.  
• Other tips for extending battery life: Do not store batteries completely discharged. Charge them  
fully before storing, and if drill is not used for a long time, take the batteries out and charge them  
periodically.  
WARNING: Always disconnect battery pack from tool or place the switch  
in the locked or off position before any assembly, adjustments or changing  
accessories.  
WARNING: Always be sure that the tool is switched off before insertion  
or removal of the battery pack.  
Installing or Removing the Battery Pack (FIG 3)  
FIG 3  
• To install the battery pack, insert the battery pack into  
drill housing as shown in FIG 3. Always insert it all the  
way until it locks in place with a little click. Lightly pull on  
the battery to ensure it is locked into place and will not  
accidentally fall out of the drill, causing an injury.  
• Do not use force when inserting the battery pack. If the  
battery does not slide in easily, it is not being inserted  
1
correctly.  
• To remove the battery pack, withdraw it from the tool  
while depressing the tabs (1) on both sides of the battery  
pack.  
18V Cordless Drill/Driver  
Operator’s Manual  
Download from Www.Somanuals.com. All ManualGs SCeDarc1h8ABnKd Download.  
Trigger Switch Action  
• Turn the drill on by depressing the trigger switch.  
• Depressing the switch further will produce more speed and torque.  
• Use the reversing switch (6-FIG 1) to change the direction of rotation of the drill.  
• The Reversing Switch has three positions: Forward, Reverse, and Off (middle).  
• Always check the rotation before beginning your work.  
LED Work Light  
Your tool has a built-in LED work light to illuminate the work area. When you turn on the tool, the  
work light will automatically turn on.  
Electric Brake  
This drill is equipped with an electric brake. Like the torque settings, an electric brake provides you  
with another element of control during various operations. If the tool consistently fails to quickly stop  
after trigger switch release, have a qualified serviceman examine the tool.  
Level  
This drill is equipped with a bubble level located on the top of motor housing. It helps you to keep the  
drill bit level during the use.  
Chuck  
• Your drill is equipped with a keyless chuck, so you can quickly change bits with no extra tools  
required.  
• To insert or change bits, put the reversing switch in the off position. Hold the collar of the chuck  
with one hand and rotate the body of the chuck to tighten or loosen.  
• Always make sure that bits are seated firmly between the chuck jaws. Never attempt to operate a  
bit that is wobbly, unstable, or broken.  
WARNING:Make sure the drill bit is inserted straight into chuck jaws.  
Do not insert the drill bit into the chuck jaws at an angle and tighten. This  
could cause the drill bit to be thrown from the drill, resulting in possible serious  
personal injury.  
Clutch (Torque) Settings  
• During screw driving applications, you can adjust the maximum torque that the drill will produce.  
• This feature can be used to prevent the stripping and breaking of screws, or to set a series of  
screws to a depth that fits your project.  
• Set the clutch ring at the front of the drill to settings from 1 (lightest) to 16 (heaviest). Setting 16 is  
direct drive (torque is not limited) and used primarily for drilling operations.  
• In general, you will find the lower settings more useful with smaller screws and the higher  
settings more useful for larger screws.  
General Screwdriving  
1. Clamp your work piece.  
2. Drill pilot holes for larger screws or when driving screws into hardwoods.  
3. Exert enough pressure to start the screw and keep it turning. Do not force the screw. Let the tool  
do the work.  
4. Use a speed that will not strip the screw head or break the screw. Maintain your balance.  
General Drilling  
1. Clamp your work piece. Use torque setting 16 then exert enough pressure to start the drill bit and  
keep it cutting. Do not force or stall the bit. Don’t bend or twist the bit. Let the tool and the blade  
do the work.  
2. Maintain your balance and be prepared for binding and for when the bit breaks through the  
material.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
11  
WARNING: Forcing a drill bit, bending or twisting the bit, or failure to  
maintain balance in case of binding and breakthrough can result in serious  
personal injury.  
3. Chattering or vibration may indicate you need a finer bit or higher speed. If the bit overheats or  
clogs, it may indicate you need a coarser bit or slower speed setting. Replace bits when they  
become dull. Dull bits will produce poor results and may overheat the drill.  
4. Use a coating of light oil when drilling into metal to keep the bit cool and to facilitate cutting.  
MAINTENANCE  
CLEANING  
Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various  
types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, dust,  
oil, grease, etc.  
WARNING: Do not at any time let brake fluids, gasoline, petroleum-  
based products, penetrating oils, etc., come in contact with plastic parts.  
Chemicals can damage, weaken or destroy plastic which may result in serious  
personal injury.  
Electric tools used on fiberglass material, wallboard, spackling compounds, or plaster are subject  
to accelerated wear and possible premature failure because the fiberglass chips and grindings are  
highly abrasive to bearings, brushes, commutators, etc. Consequently, we do not recommended using  
this tool for extended work on these types of materials. However, if you do work with any of these  
materials, it is extremely important to clean the tool using compressed air.  
LUBRICATION  
This tool is permanently lubricated at the factory and requires no additional lubrication.  
TWO-YEAR WARRANTY  
This product is warranted free from defects in material and workmanship for 2 years after date of  
purchase. This limited warranty does not cover normal wear and tear or damage from neglect or  
accident. The original purchaser is covered by this warranty and it is not transferable. Prior to returning  
your tool to store location of purchase, please call our Toll-Free Help Line for possible solutions.  
THIS PRODUCT IS NOT WARRANTED IF USED FOR INDUSTRIAL OR COMMERCIAL PURPOSES.  
ACCESSORIES INCLUDED IN THIS KIT ARE NOT COVERED BY THE 2 YEAR WARRANTY.  
TOLL-FREE HELP LINE  
For questions about this or any other GENESIS Product, please call Toll-Free: 888-552-8665.  
Or visit our web site: www.richpowerinc.com  
©Richpower Industries, Inc. All Rights reserved  
Richpower Industries, Inc.  
736 Hampton Road  
Williamston, SC 29697  
Printed in China, on recycled paper  
18V Cordless Drill/Driver  
Operator’s Manual  
Download from Www.Somanuals.com. All ManualGs SCeDarc1h8ABnKd Download.  
Richpower Industries, Inc.  
736 Hampton Road  
Williamston, SC USA  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Earthquake Sound Speaker EQ6S8 User Manual
Eiki Projector LC 5000U User Manual
Electro Voice Microphone 672A User Manual
Extron electronic Home Theater Server MLC 52 User Manual
Final Sound Portable Speaker Final 300i User Manual
Fisher Price Baby Gym B0846 User Manual
Frigidaire Freezer A01058501 User Manual
Garland Food Warmer 35 KW User Manual
GE Answering Machine 16174120 User Manual
GE Oven JKP30SM User Manual