24991
Universal Remote
Instruction Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
Battery Installation
1. On the back of the remote, push down on the
tab and lift the cover off.
2. Match the batteries to the + and - marks inside
the battery case, then insert 2 AAA Alkaline
batteries.
3. Press the battery cover back into place.
Battery Saver
Your remote automatically turns off if the buttons
are depressed more than 30 seconds. This will
save your batteries should your remote get stuck in
a place where the buttons remain depressed (e.g.,
between the sofa cushions).
Code Saver
You will have up to 10 minutes to change the
batteries in your remote without losing codes you
have programmed. However, do not press any
buttons until batteries are installed in the remote.
If buttons are pressed without batteries in the
remote, all codes will be lost.
Code Setup
The SETUP button is used to setup the remote.
You can either setup the remote using the code
for your brand of product, from the code tables (on
separate sheet), or you can search through the
library of codes until you find a code that works
for your product. Please refer to “Programming
with Code Search” page 9 for more information
on using the code search feature to learn how
to search through the library of codes for your
products. NOTE: You can store any kind of code
under any mode (except TV). I.E. you can store
a VCR code under the CABLE button, or a DVD
code under the SAT button, etc. However, you can
only store TV codes under the TV button.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Button Functions
Some buttons on the remote might have functions that
are referred to by different names on the device you
are controlling. E.G. PREV CH may be called RECALL,
or ENTER may be called DISPLAY. These differences
depend on the brand and model of your product. Also,
this remote can only operate features that exist on your
product. E.G., your product must have PREV CH ability
for the PREV CH button to operate this feature.
TV, CBL/SAT, DVD/AUX Selects
product to be operated.
VOLUME UP/DOWN
Changes the volume
level of the product,
normally the TV.
MUTE Turns off the
TV sound while the
picture remains.
OK Selects menu
items for the device
you are controlling.
PREV. CH Returns to
the previously selected
channel. EXIT Exit On-
Screen Menus and/or
Return to previous On-
Screen selection.
SETUP For setup.
SHIFT Accesses
shifted functions.
DOT
Used to select digital
channels, e.g., 5.3.
RECORD, PLAY, STOP,
REW, FF, PAUSE VCR
control buttons operate your
VCR even when the remote
is set to operate the TV.
Also operates DVD Scan
-/+. Note the VCR keys also
control DVD when in DVD
Mode.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Button Functions, cont.
Red Indicator
CHANNEL Up/Down
Lights when any but-
ton is pressed.
Changes the channels.
INPUT
For some TVs, press
repeatedly to select
from available viewing
sources (antenna, cable
box, VCR, etc.).
INFO button brings up
DVD Display or Control
Menu for Chapter/Track/
Title number, Time re-
maining/elapsed indica-
tion, system information,
etc.
MENU
Selects the on-screen
menu.
NUMBERS
Enter numbers for direct
channel selection. Some
products require ENTER
to be pressed after chan-
nel selection.
ENTER
For some TV models,
used after direct chan-
nel number
entry to immediately
change to the
selected channel.
ON-OFF Turns
device On or Off.
Note: The REC button must be pressed TWICE to record
from your VCR. For some brands of VCRs, you might
need to press the REC button once, then press it again
for three seconds.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD Functions
This remote controls many DVD functions. The
descriptions may vary from your original remote
descriptions.
REW and FF buttons control the speed of Fast
Forward and Reverse Playback respectively.
CHAN+/CHAN- buttons respectively locate the
succeeding or preceding Chapters or Tracks on a
disc.
INFO button brings up DVD Display or Control
Menu for Chapter/Track/Title number, Time remain-
ing/elapsed indication, system information, etc.
MENU brings up the DVD disc Menu screen - use
with the UP, DOWN, LEFT & RIGHT navigation
buttons.
OK button is used for on-screen Menu selection.
Note some DVD players require the Play button to
be used.
EXIT Exit On-Screen Menus and/or Return to pre-
vious On-Screen selection.
PLAY button is used to start Disc playback and for
Menu selection on some DVD players.
STOP button stops Disc playback.
PAUSE button pauses Disc playback - press PLAY
to resume.
INPUT brings up the DVD Players Setup Menu.
Note, not all DVD Players support all the functions
described above.
SAT Functions
CHAN+ and CHAN- buttons perform the “Page+”
and “Page-” function for on-screen Guide Menus
used by some Satellite systems.
INFO button brings up Satellite Display screen for
current Channel and system information.
MENU brings up the Satellite Menu screen - use
with the UP, DOWN, LEFT & RIGHT navigation
buttons.
OK button is used for on-screen Menu selection.
EXIT button is used to Exit or Clear on-screen
Menu displays.
INPUT button performs the Satellite TV/SAT func-
tion.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Direct Code Entry
1. Press and hold the SETUP button until
the red indicator stays on, then release
the SETUP button.
2. Press and release the desired mode
button (TV, DVD, etc.). The red indicator
blinks, then stays lit.
3. Enter the 4 digit code
from the code tables
(on separate sheet).
Note: after a valid
code entry, the red
indicator turns off. For
an invalid code, the
red indicator flashes.
4. With your device on, press ON/
OFF. If the device turns off, no
further programming is required.
Note: If some buttons do not
operate your equipment, try one of
the other codes for your brand.
Write your codes down here for easy reference
later.
Device
Device stored Code
TV
TV
CBL/SAT
DVD/AUX
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Code Search
If your device does not respond after you have
tried all the codes for your brand, or if your brand is
not listed, try searching for your code by following
these steps.
1. Manually turn on the device (TV, DVD, etc.) to
be controlled.
2. Press and hold the SETUP button until
the red indicator stays on, then release
the SETUP button.
3. Press and quickly release the desired
mode button (TV, DVD, etc.). The red
indicator blinks off once.
4. Press the CHANNEL UP button
repeatedly (up to 300 times) until the
device to be controlled changes
channel. The red indicator blinks
off with each button press. If you
accidentally overshoot the code
required, press the CHANNEL
DOWN button to backtrack through the library
until the device changes channel. Pressing
CHANNEL UP changes direction to forward
again.
5. Press and release ENTER to install the code.
Most users will store DVD codes under the DVD
button, Cable codes under CABLE, etc. If (for
example) you want to store a DVD code under
CABLE, first follow the procedure for Direct Code Entry
(page 8) and press CABLE in step 2 of Direct Code
Entry, then enter ANY DVD code in step 3 of Direct Code
Entry. Then follow the steps above for Code Search.
Note: If the device does not have a CHANNEL UP
button, use PLAY (DVD only) or POWER instead.
Code Search starts from the currently stored three digit
number under that mode. Sometimes the first code
that “works” with your device may only allow limited
functionality (e.g. the MENU button might not work).
There may be a code that performs more functions.
Continue the code search process until the best code is
found.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Code Identification
The Code Identification Feature allows you to
identify the 4 digit library code stored under your
device key. For example, if you want to find out
what 4 digit code is stored under your TV device
key, follow the six steps below:
1. Press and hold the SETUP button until
the red indicator stays on. Release the
SETUP button.
2. Press and release the desired mode
button (TV, DVD, etc.). The red
indicator blinks, then stays lit.
3. Press and release the SETUP button.
The red indicator blinks once and
remains lit.
4. To find the first digit for
the code stored under the
mode key pressed in step
2, press each numeric
key from 0-9 in turn. The
number that causes the
indicator light to blink is
the first digit in your code.
5. To find the second digit, repeat step 4.
6. Repeat step 4 again to find the third and fourth
digits. This time the red indicator turns off and
stays off.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your Remote
SHIFT
Press SHIFT (Setup) prior to the shifted key func-
tion e.g., for,
MENU - press and release SHIFT (Setup) then
MENU (Info).
UP - press and release SHIFT then UP (Chan+).
DOWN - press and release SHIFT then DOWN
(Chan-).
LEFT - press and release SHIFT then LEFT (Vol-).
RIGHT - press and release SHIFT then RIGHT
(Vol+).
OK - press and release SHIFT then OK (Mute).
EXIT - press and release SHIFT then EXIT (Prev.
Ch ). The red indicator blinks for each keypress.
Controlling Devices with Separate
Power On and Off Buttons
Some GE, RCA and ProScan models require
you to press the device button for more than one
second to turn the device on and the POWER
button to turn the device off.
Controlling Combo Devices
Some Combo devices (e.g. TV/VCR, TV/DVD,
DVD/VCR, etc.) will require you to set up two
different Mode buttons to control both parts of the
Combo device. For example, if you have a TV/
DVD Combo, you might need to set up one code
under the TV button to control the TV part AND a
separate code (under any other Mode button) to
control the DVD part.
VCR/DVD Punch-Through
This remote allows the 6 VCR/DVD transport
buttons (i.e. PLAY, PAUSE, STOP, FF, REWIND,
and REC) to Punch-Through control from any
Mode programmed with TV, SAT or Cable codes
to the last VCR, or DVD programmed Mode
you used. This feature will not operate if the
programmed TV, SAT or Cable code has its own
VCR transport button control e.g. a TV Combo,
SAT/PVR, etc.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your Remote, cont.
Volume/Mute Control and Punch-
Through
This remote lets you select which device Mode
controls your Volume/Mute buttons. The remote is
initially set for all device Modes to use their own
Volume/Mute control if present. If the programmed
code has no Volume/Mute operation of its own
then those buttons will punch-through control to
the TV Mode device without needing to change to
TV Mode.
Setting ALL Volume/Mute Control to
any one Mode
This routine can set all Modes to “punch-through”
to any one chosen Mode for Volume/Mute button
control without the needing to change to that
Mode.
1. Press and hold the SETUP button until the
red indicator turns on, then release the button.
2. Press and hold the MUTE button until
the red indicator blinks off, then release
the button.
3. Press and release the desired Mode button
(TV, DVD, etc.) for Volume/Mute control,
the red indicator blinks then stays on.
4. Press and release the MUTE button
and the red indicator turns off. The
red indicator will blink rapidly for
three seconds if the Mode you have
selected has no Volume/Mute control.
All other Modes will now punch-through
to your chosen Mode for Volume/Mute
control.
Download from Www.Somanuals.co1m1. All Manuals Search And Download.
Using Your Remote, cont.
Setting any Mode to use its own
Volume/Mute Control
This routine can set any Mode to use only its own
Volume/Mute control. Note - If your chosen Mode
has no Volume/Mute functions of its own then the
Volume/Mute buttons will do nothing.
1. Press and hold the SETUP button until
the red indicator turns on, then release
the button.
2. Press and hold the MUTE button until
the red indicator blinks off, then release
the button.
3. Press and release the desired Mode
button (TV, DVD, etc.), the red indicator
blinks then stays on.
4. Press and release the VOLUME- (Down)
button, the red indicator blinks then stays
on.
5. Press and release the MUTE button
and the red indicator turns off.
Your chosen Mode will now use its own
Volume/Mute control.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Remote does not operate your product.
•
Press the mode button of the product you want
to control.
•
•
Program the remote with a new code.
Install new batteries. (You might have to
reprogram your remote after installing new
batteries.)
•
Remote may not be compatible with your
product.
Remote does not operate some
features of your product.
•
Sometimes a particular code might operate
some features but not all. Try programing
remote with a new code.
•
Remote may not be able to operate all features
of your product or button names might be
different than your product.
Red Indicator blinks after you program
a product code.
•
•
Remote did not accept the code.
Try to program the code again or try a different
code.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Lost Your Codes?
Enclosed with this remote is a sticker on which
you should write the codes for each device you
programmed. Apply the sticker to the back of
the remote or somewhere convenient for future
reference.
Also on the sticker is our website address which,
should you lose your codes or programming
instructions, you can find available on our website:
Download from Www.Somanuals.com. All Manuals Search And Download.
90 Day Limited Warranty
Jasco Products Company warrants this product
to be free from manufacturing defects for a period
of ninety days from the original date of consumer
purchase. This warranty is limited to the repair
or replacement of this product only and does not
extend to consequential or incidental damage to
other products that may be used with this unit.
This warranty is in lieu of all other warranties
express or implied. Some states do not allow
limitations on how long an implied warranty lasts
or permit the exclusion or limitation of incidental or
consequential damages, so the above limitations
may not apply to you. This warranty gives you
specific rights, and you may also have other rights
which vary from state to state. If unit should prove
defective within the warranty period, return prepaid
with dated proof of purchase to:
Jasco Products Company
10 E. Memorial Road
Oklahoma City, OK 73114
Download from Www.Somanuals.com. All Manuals Search And Download.
24991
Universal Remote
Instruction Manual
Jasco Products Company
10 E. Memorial Road
Oklahoma City, OK 73114
Made in China
24991-10/08
Download from Www.Somanuals.com. All Manuals Search And Download.
|