•
•
With the rounded end of the pedestal pointing upward,
insert the tab on the end of the pedestal into the middle slot
on the bottom of the base, then push the pedestal down
until the two tabs on the left and right corners of the
pedestal snap (lock) into the two lower slots on the bottom
of the base.
Phone Does Not Ring
29385
INTRODUCTION
CALLER ID DISPLAY MESSAGES
MEMORY
•
•
Make sure ringer switch is ON.
CallWaiting Caller ID
Speakerphone with
13 Number Memory
User’s Guide
You may have too many extension phones on your line. Try unplugging some extension
phones.
The following special messages indicate the status of a message or the unit:
You may store information in any of the following memory locations: 0 to 9, A, B, and C . See
“Storing a Pause in Memory” and “Temporary Tone Dialing” for more information.
CAUTION: When using telephone equipment, there are basic safety instructions that
should always be followed. Refer to the IMPORTANT SAFETY INSTRUCTIONS
provided with this product and save them for future reference.
BLOCKED CALL
The caller of the incoming call is registered as “Private
Number” and their Caller ID information is withheld.
•Check for dial tone. See Troubleshooting Tips for No Dial Tone.
Incoming Voice Volume Low
STORING A NAME AND NUMBER IN MEMORY
Slip the mounting holes over the wall plate posts and
firmly slide the unit down into place (wall plate not
included).
CALL WAITING
Indicates a call is waiting on the line.
Battery power level is low.
Your Caller ID phone stores and displays specific information, provided by your local telephone
company, to subscribers of Caller ID or similar caller identification services.
1. Press the STORE button. LOCATION? shows in the display.
2. Press the desired memory location (0-9, A, B, C).
•
Are other phones off hook at same time? If so, this is normal condition as volume drops
when additional phones are used at once.
Your Caller ID phone enables you to:
NO CALLS
The caller memory is empty.
•
Check the handset receiver or speaker volume.
NOTE: You may select memory locations by pressing ꢀor ꢁ to scroll through the memory
locations or press the 0 - 9, A, B, C.
SETTING UP THE CALLER ID MENU
• Identify callers before you answer the phone.
• View the time and date of each incoming call.
• Record up to 75 Caller ID messages sequentially.
START/END
You are at the beginning or the end of the Caller ID memory log.
Memory Dialing
You should not plug the telephone into the modular jack while setting up the Caller ID menu.
1. Press the MENU button to enter the menu feature configuration mode.
# 1. >ENG FRA ESP (CID language default English)
# 2. CONTRAST (default level is 3).
3. Press the STORE button again to confirm the memory location.
UNKNOWN CALLER
The incoming call does not have Caller ID service or their service
area is not linked to yours. If UNKNOWN CALLER appears along
with a calling number, the name information for that number was
not available.
•
Make sure you entered the numbers correctly into memory.
NOTE: If necessary, to erase existing memories, or if you make a mistake, use the
DELETE button.
GENERAL PRODUCT CARE
IMPORTANT: In order to use all of the features of this telephone, you must subscribe to two
separate services available from your local telephone company: the standard Name/Number
Caller ID Service to know who is calling when the phone rings and Caller ID with Call Waiting
Service to know who is calling while you are on the phone.
4. Use the number keys to enter the telephone number (up to 32 digits) and press the STORE
button to save. (The unit will not dial a phone number in this mode.) The cursor
automatically moves to the text line for name entry.
To keep your phone working and looking good, follow these guidelines:
# 3. LOCAL AREA CODE
SPEAKERPHONE BASICS
•
Avoid putting it near heating appliances and devices that generate electrical noise (for
example, motors or fluorescent lamps).
# 4.TONE/PULSE (Default is tone dialing).
5. Use the number keys to enter the name of the person associated with the telephone number
you just entered. More than one letter is stored in each of the number keys.
2. Press the MENU button to scroll through the 4 menu screens.
3. Use the ꢀor ꢁ buttons to select the desired setting.
NOTE: You have 20 seconds following an entry before the phone returns to the Summary Screen.
SHORT GLOSSARY OF TERMINOLOGY USED IN
THIS MANUAL
•
•
•
•
•
DO NOT expose to direct sunlight or moisture.
Avoid dropping and other rough treatment to the unit.
Clean with a soft cloth.
For example, to enter the name BILL SMITH, press the 2 key twice for the letter B. Press the
4 key 3 times for the letter I. Press the 5 key 3 times for the letter L.
display
NOTE: The flashing cursor automatically moves to the next position or you may press
the ꢀor ꢁ buttons to move the cursor to the next position.
Hook switch. The part of the phone that pops up to activate the phone line when the handset is
Never use a strong cleaning agent or abrasive powder because this will damage the finish.
Retain the original packaging in case you need to ship it at a later date.
DISPLAY LANGUAGE
lifted from the base.
DIAL
button
Press the 5 key 3 times for the second letter L. Press the arrow key (4) two times to insert a
space, and press the 7 key 4 times for the letter S. Press the 6 key once for the letter M.
Press the 4 key 3 times for the letter I. Press the 8 key for the letter T. Press the 4 key twice
for the letter H.
Off-hook. A term used to describe the phone in its active mode when the handset is off of the
base cradle or when the SPEAKER button is pressed.
DELETE
button
This adjustment allows you to display the Caller ID prompts in English, French, or Spanish.
1. Press the MENU button until ENG FRA ESP shows in the display.
2. Use the ꢀor ꢁ buttons to select ENG, FRA or ESP.
SERVICE
On-hook. A term used to describe the phone in an inactive mode.
If trouble is experienced with this equipment, for repair or warranty information, please contact
customer service at 1-800-448-0329. If the equipment is causing harm to the telephone
network, the telephone company may request that you disconnect the equipment until the
problem is resolved.
6. Press the STORE button to save the name.
3. Press the MENU button again to save.
MENU
button
STORE
button
BEFORE YOU BEGIN
7. To enter another name and number in a different memory location, return to step 1 and
repeat the process.
CONTRAST
PARTS CHECKLIST
This product may be serviced only by the manufacturer or its authorized service agents.
Changes or modifications not expressly approved by ATLINKS USA, Inc. could void the user’s
authority to operate this product. For instructions on how to obtain service, refer to the
warranty included in this guide or call customer service at 1-800-448-0329.
This adjustment allows you to adjust the contrast of the display.
1. Press the MENU button until CONTRAST shows in the display.
2. Use the ꢀor ꢁbuttons to select level 1, 2, 3, 4, or 5.
3. Press the MENU button again to save.
CHANGING A STORED NUMBER
Make sure your package includes the following items:
Repeat the storage sequence under Storing A Name and Number in Memory, and use the
DELETE button to delete the old number before entering the new number.
Or refer inquiries to:
ATLINKS USA, Inc.
Manager, Consumer Relations
P O Box 1976
Indianapolis, IN 46206
ERASING A STORED NUMBER
LOCAL AREA CODE
1. Press the STORE button.
FLASH/EXIT
button
The telephone uses the programmed area codes to determine the number format to display
when a valid Caller ID signal is received. Numbers that match the local area code are
displayed as seven digits and are used for dialing back previous numbers. Entering your local
area code will also help you immediately know if the call is local or long distance when viewing
the CID records in the display.
MUTE
button
2. Press the memory location (0-9, A, B, C) to be erased.
3. Press the DELETE button.
Attach your sales receipt to the booklet for future reference or jot down the date this product
was purchased or received as a gift. This information will be valuable if service should be
required during the warranty period.
VOL
button
We bring good things to life.
Base
Handset
Handset cord
Desktop/wall
mounting pedestal
2-wire telephone
line cord
SPEAKER
button
COPYING CALLER ID MEMORIES TO USER
MEMORY
REDIAL/PAUSE
button
NOTE: If you make a mistake and want to start over again, press the DELETE button to erase
all of the digits.
Purchase date ________________________________________________
Name of store ________________________________________________
LOCATION
Wall plate
TELEPHONE JACK REQUIREMENTS
1. Press the ꢀor ꢁ buttons to view the caller number and name you want to copy.
1. Press the MENU button until LOCAL AREA CODE shows in the display.
2. Press the ꢀ button to select digit.
Your phone features a speakerphone for ease of use and convenience during a phone
conversation. At any time during a conversation, you can lift the handset to stop using the
speakerphone. Likewise, when you are using the handset, press the SPEAKER button and place
the handset in the cradle to switch to the speakerphone.
EQUIPMENT APPROVAL INFORMATION
2. Press the STORE button.
To use this phone, you need an RJ11C type modular telephone jack,
which might look like the one pictured here, installed in your home. If
you don’t have a modular jack, call your local phone company to find
out how to get one installed.
Modular
telephone
line jack
LIMITED WARRANTY
Your telephone equipment is approved for connection to the Public Switched Telephone
Network and is in compliance with parts 15 and 68, FCC Rules and Regulations and the
Technical Requirements for Telephone Terminal Equipment published by ACTA.
3. Press the memory location (0-9, A, B, C). The number flashes if there is a number already
stored in the memory location.
3. Press the ꢁ button to enter the second and third digit.
4. Press the MENU button to save.
What your warranty covers:
For best speakerphone performance, avoid the following:
4. Press the STORE button to enter the edit mode, and then press the STORE button again to
edit the name.
•
Defects in materials or workmanship.
1
Notification to the Local Telephone Company
•
Areas with high background noise. (The microphone might pick up these sounds and
prevent the speakerphone from going into the receiving mode when you finish talking.)
DIALING MODE
For how long after your purchase:
On the bottom of this equipment is a label indicating, among other information, the US
number and Ringer Equivalence Number (REN) for the equipment. You must, upon request,
provide this information to your telephone company.
IMPORTANT INSTALLATION INFORMATION
NOTE: You may select a different memory location by pressing ꢀor ꢁ to scroll through the
memories or press a number key (0-9, A, B, C).
•
One year, from date of purchase.
This adjustment allows you to select tone (touch-tone) or pulse (rotary) dialing.
•
•
Surfaces affected by vibration.
CAUTION: Disconnect the phone cord from the wall outlet before installing or
(The warranty period for rental units begins with the first rental or 45 days from date of
shipment to the rental firm, whichever comes first.)
1. Press the MENU button until TONE/PULSE MODE shows in the display.
2. Press the ꢀor ꢁ buttons to show the current dialing mode. The default is TONE dialing.
replacing the batteries.
Recessed areas such as in a corner, under a cupboard, or next to a cabinet, which can
generate an echo effect.
5. Press the STORE button to confirm and save, and wait for three seconds to exit.
The REN is useful in determining the number of devices you may connect to your telephone
line and still have all of these devices ring when your telephone number is called. In most
(but not all) areas, the sum of the RENs of all devices connected to one line should not
exceed 5. To be certain of the number of devices you may connect to your line as
determined by the REN, you should contact your local telephone company.
•
•
Never install telephone wiring during a lightning storm.
NOTE: If the name you want to enter is longer than 12 characters, only the first 12 characters
will be copied into memory.
What we will do:
3. To change the dialing mode, press the ꢀor ꢁ buttons. The display alternates between the
Never touch uninsulated telephone wires or terminals, unless the telephone line has been
disconnected at the network interface.
SPEAKERPHONE USE
•
Provide you with a new or, at our option, a refurbished unit. The exchange unit is under
warranty for the remainder of the original product’s warranty period.
two modes.
4. Press the MENU button again to save.
Note the following guidelines when using the speakerphone:
COPYING REDIAL NUMBERS TO MEMORY
•
•
Use caution when installing or modifying telephone lines.
How you get service:
A plug and jack used to connect this equipment to the premises wiring and telephone
network must comply with the applicable FCC Part 68 rules and requirements adopted by
the ACTA. A compliant telephone cord and modular plug is provided with this product. It is
designed to be connected to a compatible modular jack that is also compliant. See
installation instructions for details.
NOTE: The phone will exit Set Up after 20 seconds if no buttons are pressed.
•
•
•
•
The speakerphone works similar to a two-way radio in that you can only listen or talk at
one time.
Never install telephone jacks in wet locations unless the jack is specifically designed for
wet locations.
1. Press the REDIAL button while the phone is on-hook. The display shows PICKUP PHONE.
2. Press the STORE button.
•
Properly pack your unit. Include any cables, etc., which were originally provided with the
product. We recommend using the original carton and packing materials.
REMINDER: The time and date are programmed automatically when the first Caller ID record
is successfully received after set up.
Stay reasonably close to the phone so that you can be clearly heard by the person to whom
you are talking.
•
Temporarily disconnect any equipment connected to the phone, such as faxes, other
phones, or modems.
•
”Proof of purchase in the form of a bill of sale or receipted invoice which is evidence that
the product is within the warranty period, must be presented to obtain warranty service.”
For rental firms, proof of first rental is also required. Also print your name and address and
a description of the defect. Send via standard UPS or its equivalent to:
3. Press any number key (0-9, A, B, C) for the memory location. The cursor flashes and allows
the user to enter the caller's name.
CALLER ID (CID) FEATURES
You can adjust the speaker volume by pressing the volume button continuously or pressing
the review button or after pressing the volume button.
Notes
•
4. Press the STORE button twice to confirm and save, and wait for three seconds to exit.
INSTALLING AND REPLACING THE BATTERIES
This equipment may not be used on coin service provided by the telephone company.
NOTE: If you want to edit the number, press the STORE button again within three seconds.
When you are finished, wait three seconds to exit.
The speakerphone indicator light comes on when the speakerphone is in use.
CID SUMMARY SCREEN
ATLINKS USA, Inc.
c/o Thomson
11721 B Alameda Ave.
Socorro, Texas 79927
•
Party lines are subject to state tariffs, and therefore, you may not be able to use your
own telephone equipment if you are on a party line. Check with your local telephone
company.
Your Caller ID phone uses 4 AA-size alkaline batteries for receiving and storing Caller ID
records and for storing the numbers you use for memory dialing, pulse dialing, and redial.
NOTE: Batteries must be installed for the speakerphone to operate.
The Summary Screen shows the current time, date, and number of new calls to review. It is
displayed until any button is pressed.
IMPORTANT: You will have approximately 90 seconds to replace the batteries before the
memories stored are lost. Please read the instructions before replacing the batteries and have
the batteries ready to be inserted beforehand.
DIALING A NUMBER STORED IN MEMORY
TELEPHONE BASICS
•
•
Notice must be given to the telephone company upon permanent disconnection of your
telephone from your line.
NOTE: The number of new calls is displayed until all new calls have been reviewed.
•
•
•
Pay any charges billed to you by the Exchange Center for service not covered by the
warranty.
WHILE ON-HOOK
You can use the telephone by speaking into and listening through the handset, or by using the
speakerphone.
If your home has specially wired alarm equipment connected to the telephone line,
ensure the installation of this product does not disable your alarm equipment. If you
have questions about what will disable alarm equipment, consult your telephone
company or a qualified installer.
IMPORTANT: If you are not going to use the telephone for more than 30 days, remove the
batteries because they may leak and damage the unit.
RECEIVING AND STORING CID CALLS
1. Press the DIAL button
Insure your shipment for loss or damage. ATLINKS accepts no liability in case of damage
or loss.
This unit receives and displays information transmitted by your local phone company. This
information can include the phone number, date, and time; or the name, phone number, date,
and time. The unit can store up to 75 calls for later review. When the memory is full, a new call
automatically replaces the oldest call in memory. NEW appears in the display for calls received
that have not been reviewed.
2. To select a memory, press any number key (0-9, A, B, C). The number in that memory
location displays.
RECEIVING A PHONE CALL
1. If the telephone line cord is connected, disconnect it from the base unit.
A new or refurbished unit will be shipped to you freight prepaid.
2. Carefully turn over the phone, and press down and out on
the snap tab located on the top of the mounting bracket. Lift
the bracket off.
1. Lift the handset or press SPEAKER to answer the call.
NOTE: You may select a different memory location by pressing ꢀor ꢁ to scroll through the
memories or press a number key (0-9, A, B, C).
2
Rights of the Telephone Company
What your warranty does not cover:
Should your equipment cause trouble on your line which may harm the telephone network, the
telephone company shall, where practicable, notify you that temporary discontinuance of
service may be required. Where prior notice is not practicable and the circumstances warrant
such action, the telephone company may temporarily discontinue service immediately. In case
of such temporary discontinuance, the telephone company must: (1) promptly notify you of such
temporary discontinuance; (2) afford you the opportunity to correct the situation; and (3) inform
you of your right to bring a complaint to the Commission pursuant to procedures set forth in
Subpart E of Part 68, FCC Rules and Regulations.
The telephone company may make changes in its communications facilities, equipment,
operations or procedures where such action is required in the operation of its business and not
inconsistent with FCC Rules and Regulations. If these changes are expected to affect the use or
performance of your telephone equipment, the telephone company must give you adequate notice,
in writing, to allow you to maintain uninterrupted service.
2. Replace the handset in the cradle or press the SPEAKER button to hang up.
•
Customer instruction. (Your Owner’s Manual provides information regarding operating
instructions and user controls. Any additional information, should be obtained from your
dealer.)
3. Press the SPEAKER button, or pick up the handset to dial the displayed number.
3. Release latch on battery compartments and remove cover.
MAKING A PHONE CALL
REVIEWING CID RECORDS
4. Insert 4 AA-size alkaline batteries as shown on the diagram
in the battery compartments.
DIALING A NUMBER STORED IN MEMORY
•
•
•
•
•
•
Installation and setup service adjustments.
Batteries.
1. Lift the handset or press the SPEAKER button. Wait for a dial tone.
2. Dial the telephone number you want to call.
•
•
•
•
Press the ꢀor ꢁ buttons to view the call records.
1. Lift the handset, or press the SPEAKER button.
Press the ꢁ button to scroll through the call records from the most recent to the oldest.
Press the ꢀ button to scroll through the call records from the oldest to the newest.
When all of the records have been viewed, START/END appears in the display.
5. Snap the battery compartment doors back into place and
replace the mounting bracket.
2. Press the DIAL button then press a memory location button.
Damage from misuse or neglect.
3. Replace the handset in the cradle, or press the SPEAKER button to hang up.
Products which have been modified or incorporated into other products.
Products purchased or serviced outside the USA.
Acts of nature, such as but not limited to lightning damage.
6. If the line cord was previously connected, re-attach it to the
unit and check your memory locations.
CASCADE DIALING
VOLUME
This process allows you to dial a succession of stored numbers from separate memory
locations. This is useful when you must dial several sequences of numbers, such as with
frequent calls via a telephone company long distance provider.
NOTE: If the low battery icon appears in the display, you need to replace the batteries.
It is important that you replace the batteries as soon as possible in order to maintain
Caller ID operation.
DELETING CID RECORDS
You may adjust the handset and speakerphone volume independently with the VOL button or
the ꢀor ꢁ buttons. Both handset receiver volume level and speakerphone volume level are
saved in memory.
Product Registration:
•
•
To delete the record shown in the display, press the DELETE button once.
•
Please complete and mail the Product Registration Card packed with your unit. It will make
it easier to contact you should it ever be necessary. The return of the card is not required
for warranty coverage.
To delete all records while reviewing, press and hold the DELETE button for about three
seconds. DELETE ALL? appears in the display. Press DELETE again to complete.
For example
Memory location
INTERFERENCE INFORMATION
ADJUSTING THE HANDSET RECEIVER VOLUME
INSTALLING THE PHONE
Local access number of long distance company
Authorization code (ID)
6
7
8
While using the handset, you can adjust the speaker volume by pressing the VOL button
continuously or pressing the ꢀor ꢁ buttons after pressing the VOL button. REC (Handset
Receiver) volume shows in the display.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference; and (2) This device must accept any
interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Your phone should be placed on a level surface, such as a desk or table top, or you can mount it on
a wall. A desktop/wall mounting pedestal is packaged with your phone.
DIALING BACK
Limitation of Warranty:
Long distance phone number
•
•
THE WARRANTY STATED ABOVE IS THE ONLY WARRANTY APPLICABLE TO THIS
PRODUCT. ALL OTHER WARRANTIES, EXPRESS OR IMPLIED (INCLUDING ALL IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE) ARE
HEREBY DISCLAIMED. NO VERBAL OR WRITTEN INFORMATION GIVEN BY ATLINKS USA,
INC., ITS AGENTS, OR EMPLOYEES SHALL CREATE A GUARANTY OR IN ANY WAY
INCREASE THE SCOPE OF THIS WARRANTY.
When reviewing Caller ID records, you can dialback the numbers on the display by pressing
the DIAL button.
ATTACHING THE DESKTOP PEDESTAL
ADJUSTING THE SPEAKERPHONE VOLUME
1. Pick up the handset or press SPEAKER.
NOTE: If PICKUP PHONE shows in the display, no other changes to the number can be made.
The information sent from the telephone company is known to be a valid number for dialing
back (used only in very limited areas). Once you pickup the phone, the number is
automatically dialed.
While using the speakerphone, you can adjust the speaker volume by pressing the VOL button
continuously or pressing the ꢀor ꢁ buttons after pressing the VOL button. SPK volume level
shows in the display.
•
Turn the phone over so that the bottom of the base is facing up and the thickest end is
facing away from you.
2. Press DIAL button, then press number “6” for the memory location.
3. Press DIAL button, then press number “7” for the memory location.
4. Press DIAL button, then press number “8” for the memory location.
5. The number dials automatically.
•
With the rounded end of the wedge pointing downward, insert the tab on the rounded end
of the pedestal into the middle slot on the bottom of the base, then push the pedestal down
until the two tabs on the left and right corners of the pedestal snap (lock) into the two upper
slots on the bottom of the base.
REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE
REMEDY OF THE CONSUMER. ATLINKS USA, INC. SHALL NOT BE LIABLE FOR INCIDENTAL
OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT OR
ARISING OUT OF ANY BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS
PRODUCT. THIS DISCLAIMER OF WARRANTIES AND LIMITED WARRANTY ARE GOVERNED
BY THE LAWS OF THE STATE OF INDIANA. EXCEPT TO THE EXTENT PROHIBITED BY
APPLICABLE LAW, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED TO THE APPLICABLE WARRANTY
PERIOD SET FORTH ABOVE.
NOTE: Both handset receiver and speakerphone volume return to the default setting (low) if
the unit is power up reset.
IF YOU PROGRAMMED YOUR LOCAL AREA CODE
1. Use the ꢀor ꢁ buttons to display the number you want to dial.
2. Press the DIAL button.
REDIAL
STORING A PAUSE IN MEMORY
•
•
•
Reorient or relocate the receiving antenna (that is, the antenna for radio or television that is
“receiving” the interference).
Reorient or relocate and increase the separation between the telecommunications equipment
and receiving antenna.
CONNECTING THE HANDSET
You may redial the last number you called by pressing the REDIAL button after you hear a
dial tone.
The REDIAL button has dual functionality and becomes a pause button when the STORE button
is pressed first. It is valid only when storing a number into memory locations. Use the PAUSE
(REDIAL) button to insert a pause when a delay is needed in an automatic dialing sequence. For
example, when you must dial a 9 to get an outside line or when you enter codes to access your
long distance company.
•
If you see a number with seven digits (i.e. 555-1234), then the call is from within your area
code. However, this does not guarantee the call is a local call.
1. Connect one end of the coiled handset cord to the jack on the handset.
2. Plug the other end of the coiled handset cord to the jack on the base.
3. Place the handset in the cradle.
NOTE: The redial feature holds the last number (up to 32 digits) that you dialed in memory. If
you pressed any other numbers after dialing the phone number (for example, when accessing a
voice-menu system) then those numbers are also dialed.
•
If you see a number with 11 digits (i.e. 1-234-555-1234), then the call is not from within your
area code.
Connect the telecommunications equipment into an outlet on a circuit different from that to
How state law relates to this warranty:
which the receiving antenna is connected.
NOTE: A timer (10 seconds on-hook and 3 seconds off-hook) located in the upper right side of
the display will start, letting you know how much time is left until the unit returns to the
Summary Screen.
•
Some states do not allow the exclusion nor limitation of incidental or consequential
damages, or limitations on how long an implied warranty lasts so the above limitations or
exclusions may not apply to you.
If these measures do not eliminate the interference, please consult your dealer or an
experienced radio/television technician for additional suggestions. Also, the Federal
Communications Commission has prepared a helpful booklet, “How To Identify and Resolve
Radio/TV Interference Problems.” This booklet is available from the U.S. Government Printing
Office, Washington, D.C. 20402. Please specify stock number 004-000-00345-4 when ordering
copies.
CONNECTING THE TELEPHONE LINE
PRE-DIALING
MUTE
1. Connect one end of the straight telephone line cord to the jack on the back of the base.
2. Connect the other end to a wall phone jack.
1. With the handset on the cradle, enter the telephone number you wish to call. The telephone
number shows in the display.
Use the MUTE button to interrupt a phone conversation to talk privately with someone else in
the room. A conversation can be muted while using the speakerphone or handset.
3. If you are at on-hook and PICKUP OR ADJ displays, you can adjust the phone number
format by pressing the DIAL button. If the phone is off-hook and ADJUST shows in the
display, you can adjust the phone number format by pressing the DIAL button. For example,
sometimes a 7-digit local number cannot be dialed because it requires a 10-digit or 11-digit
format. Press the DIAL button repeatedly to scroll through the 7, 10, and 11-digit numbers.
•
This warranty gives you specific legal rights, and you also may have other rights that vary
from state to state.
3. Set the RINGER volume switch located at
the back of the base to the desired
loudness.
2. Lift the handset or press the SPEAKER button and the number automatically dials.
1. Press the MUTE button. The mute indicator illuminates.
2. Press MUTE again to turn it off.
If you purchased your product outside the USA:
This warranty does not apply. Contact your dealer for warranty information.
NOTE: Use the DELETE button to delete an incorrectly entered number.
•
HEARING AID COMPATIBILITY (HAC)
NOTE: Switching from speakerphone to handset cancels mute.
OFF - Telephone will not ring.
LO - Sound will be lowest.
HI - Sound will be loudest.
TROUBLESHOOTING TIPS
7-digits:
10-digits:
11-digits:
7-digit telephone number (i.e. 555-5555)
This telephone system meets FCC standards for Hearing Aid Compatibility.
FLASH
No Dial Tone
3-digit area code + 7-digit telephone number (i.e. 425-555-5555)
US NUMBER IS LOCATED ON THE CABINET BOTTOM
REN NUMBER IS LOCATED ON THE CABINET BOTTOM
Press FLASH to activate special features of your telephone network, such as call transfer, or
special services from your local telephone company, such as call waiting.
•
•
Check all cabling to make sure that all connections are secure and not damaged.
Check hook switch: Does it fully extend when handset is lifted from cradle?
long distance code 1 + 3-digit area code + 7-digit telephone number
(i.e. 1-425-555-5555)
NOTE: The unit is properly installed if you
pick up the handset and hear the dial tone.
Otherwise, recheck all installation steps.
4. To dial the displayed number, and the phone is on-hook, pick up the handset or press the
SPEAKER button before the timer reaches 0. If the phone is off-hook, wait until the time
reaches 0. NOW DIALING shows in the display and the number is dialed.
No Display
TEMPORARY TONE DIALING
•
•
Replace the batteries.
Check for proper battery installation.
WALL MOUNTING
If you have pulse (rotary) service and want to access customer calling services (such as
telebanking and long distance services) that require tone dialing, you can use this feature to
temporarily change from pulse to tone service.
Your speakerphone can also be mounted on a wall plate (not included).
IF YOU DID NOT PROGRAM YOUR LOCAL AREA CODE
No Information is Shown After the Phone Rings
After dialing the telephone number and connecting to the customer calling service,
1. Press and release the TONE (*) button.
1. Use th ꢀor ꢁ buttons to display the number you want to dial. You will only see 10-digit
•
•
Are you subscribed to Caller ID service from your local telephone company?
Be sure to wait until the second ring before answering.
ATTACHING THE WALL MOUNTING PEDESTAL
numbers (i.e. 234- 555-1234).
•
Turn the phone over so that the bottom of the base is facing up and the thickest end is
pointing away from you.
2. See steps 2 through 4 in the previous section to complete the dialback process.
2. When you hang up, the telephone automatically returns to pulse dialing mode.
Phone Dials in Pulse with Tone Service
Make sure T/P DIAL MODE is set to TONE DIAL.
Phone Won't Dial Out with Pulse Service
Make sure T/P DIAL MODE is set to PULSE DIAL.
ATLINKS USA, Inc.
101 West 103rd Street
•
If desired gather the extra telephone line cord together and store inside the wall mounting
pedestal, and then thread the line cord through the grooves on the pedestal according to
the illustration.
TIP: Temporary Tone can also be used while storing numbers in memory by pressing TONE
(*) at the necessary point in the storage sequence.
•
Indianapolis, IN 46290
© 2004 ATLINKS USA, Inc.
Trademark(s) ® Registered
Marca(s) Registrada(s)
Model 29385
00000737 (Rev. 2 E/S)
04-50
•
Printed in China
Download from Www.Somanuals.com. All Manuals Search And Download.
|