GE Door 19216 User Manual

GE Model 19216  
Setting The House Security Code  
4. Locate the chime and pushbutton jumpers shown  
above.  
2. Before mounting, choose a mounting location that  
is not farther than 150 feet from the chime unit  
location.  
2. Gently press transmitter button to sound chime.  
Each chime component has 4 jumpers for setting the  
house security code. In most cases you will not need  
to change the factory settings for the house security  
code. If your chime activates intermittently or does not  
work at all, you may be able to solve the problem by  
changing your security code.  
5. To change the house code, add or remove jumpers  
as needed. It is recommended to change only one  
jumper at a time and then test the system for proper  
operation. The jumpers on the chime and pushbutton  
must match exactly.  
Troubleshooting  
Not further than 150 feet  
Chime doesn’t work:  
1. Make sure push button switch is depressed and held  
for at least 1 second.  
2. Make sure house code switches 1-4 on chime and  
push button match exactly.  
Wireless Door Chime Kit  
Installation Instructions AC Wireless Chime Kit  
Required Tools: Small flat blade screwdriver, drill,  
1/16” drill bit, and phillips screwdriver.  
Wireless push button battery  
3. Verify battery orientation in push button.  
4. Try fresh batteries.  
To install or replace the battery in the wireless push  
button.  
5. Make sure chime is not farther than 150 feet away  
from push button.  
6. Ensure push button is not mounted on metal, near  
metal studs, or near the floor.  
7. Try a new location for the chime.  
Included Hardware:  
(2) 3x20mm screws  
(1) Double sided adhesive pad  
1. Remove the back cover of the push button.  
The wireless door chime kit has two components:  
3. Before placing the pushbutton where you would like  
to mount it, place the chime as close to final position  
as possible. Test the operation before drilling. If it  
works, mount the push button. If it does not work,  
see TROUBLESHOOTING.  
Functional range may be adversely affected by one or  
more of the following factors: weather, radio frequency  
interference, low transmitter battery and obstructions  
between the transmitter and receiver.  
This device complies with Part 15 of the FCC rules.  
Operation is subject to the following conditions:  
1. This device may not cause harmful interference, and  
2. This device must accept interference received,  
including any interference that may cause undesired  
operation.  
4. Use back cover of push button as a template to mark  
two screw holes.  
2. Install the A23 (12 volt) battery with the negative  
side of the battery (-) toward the spring and the  
positive side of the battery (+) toward the positive  
battery holder as shown below.  
Battery Operated  
PushButton (Transmitter)  
Battery included  
4
For technical support contact Jasco Products  
Company at 1-800-654-8483  
Chime (Receiver)  
Plugs into 120V outlet  
Pushbutton  
House Code  
Jumpers  
5
Chime Tune Setting  
Made in China  
All wireless chimes may have more than one push  
button. The chime tune for each push button is set with  
dip switches 1-3. Located inside the push button.  
Chime Dip  
Switches  
is a trademark of  
6
General Electric Company  
and is used under license to  
Jasco Products Company LLC,  
10 E. Memorial Rd.,  
Oklahoma City, OK 73114.  
8
3. Replace back cover as shown below.  
Single Push Button Kit: If you purchased a kit with a  
single push button, the chime tune will be set to Ding  
Dong from the factory.  
Dual Push Button Kit: If you purchased a kit with two  
push buttons, one push button will be set to Ding Dong  
and the other push button will be set to Westminster  
from the factory.  
5. Drill two holes with 1/16” size drill in marked  
locations.  
6. Secure back cover to the mounting surface with two  
supplied mounting screws.  
7. Install the supplied 12V battery observing proper  
polarity. (see battery installation section)  
8. Press front housing onto back cover.  
9. Test operation. If the chime does not work, see  
TROUBLESHOOTING.  
If you do not want to drill holes in your door frame, you  
can use the supplied double sided tape for installation.  
1. Clean all mounting surfaces with a 50/50 mixture of  
isopropyl alcohol.  
2. Remove the backing from one side of the double  
sided tape and press the exposed side against the  
back plate of the push button.  
3. Remove the other backing strip and press the  
exposed side against the door frame where you want  
the button installed.  
The chime and pushbutton must be set to the same  
house security code for the combination to operate  
together.  
Rev. 10-07  
The following instructions explain how to change the  
tune on any wireless push button.  
19216  
1. Remove power from the chime.  
2. To remove the batteries from the pushbutton, open  
the pushbutton case as shown below.  
Push Button Mounting Instructions  
Note: Avoid mounting on metal surfaces, as it may  
result in a reduced range of transmission. Do not mount  
in an area where exposed to direct rain.  
1. Remove the cover from the push button - see  
wireless push button battery.  
2. Remove the battery from the push button transmitter.  
3. Locate the 3 dip switches shown below.  
4. Select the desired chime sound from the table below.  
a. Removing the back cover  
Chime Sound Table  
Position  
1
2
3
Westminster  
Ding Dong  
Knock  
Bronze Chime  
Cuckoo Clock  
Foghorn  
ON  
OFF  
OFF  
ON  
ON  
OFF  
ON  
OFF  
ON  
OFF  
ON  
OFF  
ON  
ON  
OFF  
OFF  
ON  
OFF  
ON  
ON  
ON  
Pushbutton  
House Code  
Jumpers  
Power Indicator  
b. Replacing the back cover  
Gong  
Chime Dip  
Switches  
Pushbutton House Code Jumpers Chime Dip Switches  
On/Off Switch  
Pushbutton Jumpers  
Operation  
Mounting Push Button  
3. Locate the House Security Code door and screw  
located on the back of the Chime. Remove the  
screw and take off the door.  
1. Push buttons are typically mounted at the same  
height as the door knob or handle (between 36” and  
44” above the floor).  
1. Plug the chime into a 120V AC outlet and slide the  
power switch to the “On” position to turn on the  
chime. The red LED power indicator will light.  
Pushbutton Dip Switches and Jumpers  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Edelbrock Automobile Parts 1797 User Manual
EFJohnson Satellite Radio 002 9800 401 User Manual
Electro Voice Portable Speaker KD9 User Manual
Fisher Paykel Cooktop CE901 User Manual
Flymo Trimmer CT250 User Manual
Fundex Games Games 2428 User Manual
GE IP Phone 25600 MGCP User Manual
GE TV Converter Box F485 User Manual
GE Two Way Radio LBI 31564A User Manual
Global Machinery Company Drill HD2G250M User Manual