SPARTAN LAMINATOR
OPERATION & MAINTENANCE
MANUAL
Part Number: 930-073 Rev: A Rev. Date: 6-9-04
© 2004 GENERAL BINDING CORPORATION. ALL RIGHTS RESERVED.
Do not duplicate without written permission.
General Binding Corporation
One GBC Plaza
Northbrook, IL 60062-4195
Download from Www.Somanuals.com. All Manuals Search And Download.
Spartan Operation and Maintenance Manual
Table of contents
1.0 Safety
1.1 Explanation of symbols
1.2 General Rules of safety
1.3 Primary function
1-1
1-1
1-2
1-2
1-3
1.4 Safety decals
Figure 1.4.1 Safety label placement
2.0 Warranty
2.1 Limited warranty
2.2 Exclusions to the warranty
2.1
2-1
3.0 Specifications
3.1 Consumable
3-1
3-1
3-1
3-1
3-2
3.2 Function
3.3 Electrical
3.4 Dimensions and weights
Figure 3.4.1 Dimensions
4.0 Installation
4.1 Pre-installation
4-1
4-2
4-2
4-3
4-4
4.2 Suggested floor layout
Figure 4.2.1 Suggested floor layout example
4.3 Know your laminator
4.4 Unpacking
5.0 Operations
5.1 Control panel
5-1
5-2
5.2 Roller pressure handle
6.0 Applications
6.1 Pouch boards
6-1
6-2
6-3
6-4
6.2 Mounting boards
6.3 Lamination pouches
6.4 Helpful Hints
7.0 Maintenance
7.1 Cabinets, cover and stand
7.2 Rollers
7-1
7-1
7-1
7-2
7.2.1 Stains/ dust on rollers
7.2.2 Adhesive on rollers
© 2004 General Binding Corporation
Page I
Download from Www.Somanuals.com. All Manuals Search And Download.
Spartan Operation and Maintenance Manual
Page II
© 2004 General Binding Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Spartan Operation and Maintenance Manual
1.0 Safety
ELECTRICAL HAZARD: [This symbol is used prior
to a step. The information following this symbol is to
prevent an electrical shock condition that may be
caused by an operator’s action or machine function..]
CAUTION: Do not attempt to operate your
SPARTAN Laminator until you completely read and
understand this Operations and Maintenance
Manual.
1.2 General rules of safety
Your safety, as well as the safety of others, is important to
General Binding Corporation (GBC). This section
contains important safety information which must be
adhered to while operating, cleaning and performing basic
maintenance in and around the machine.
ELECTRICAL HAZARD: Do not operate the
laminator if power cord is damaged or frayed. You
can be severely shocked, electrocuted or cause a
fire.
1.1 Explanation of symbols
WARNING: Do not operate this machine if your are
not physically, psychologically or emotionally fit. Do
not operate this machine until you have been trained
and have read this manual in its entirety.
INFORMATION: [This symbol is used prior to,
during and/ or after a step. Following this symbol is
important information pertaining to current subject.]
WARNING: Do not wear ties, loose fitting clothes
or dangling jewelry while operating or servicing the
laminator. These items can get caught in the nip and
choke you or you can be crushed or burned.
CAUTION: [This symbol is used prior to a step. The
information following this symbol is to inform you of
how to avoid harm to you, others around you or to
the equipment.]
WARNING: Never tamper with the safety devices
to increase the laminator’s production capacity. In
the event a safety device should fail, never attempt
to bypass it for operation. Consult a service
representative immediately.
WARNING: [This symbol is used prior to a step. The
information following this symbol is to inform you of
how to avoid a dangerous situation.]
© 2004 General Binding Corporation
Page 1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Spartan Operation and Maintenance Manual
1.3 Primary function
1.4 Safety decals
INFORMATION: Always observe all warning
labels placed at various points on the laminator. If
you do not completely understand a label, consult
your manager for assistance.
WARNING: Never use this machine for any other
purpose than its intended design and function.
The Spartan laminator is to be used only as a mounting
and laminating machine. Only use acceptable materials
when mounting and laminating with this machine.
– Electrical Shock: Electrical shock hazard.
Electrical voltage behind panel.
All acceptable materials may be purchased from GBC.
For your convenience, acceptable materials are listed
below with product code numbers for fast and easy
ordering.
!
MUCHO
CUIDADO
!
MUCHO
CUIDADO
!
!
!
!
WARNING
WAARSCHUWING
ATTENZIONE
WARNUNG
Kans op
elektrische
schok.
Niet openen
Bevatgeen door
gebruik te
Riesgo de
choque
electrico
No abra
Adentro, no hay
piezas
reparables
para el usuario.
Mantenimiento
solamente para
personal
Pericolo di
scarica
elettrica.
Nessuna parte
riparabile
dall' utente.
Chiamare un
servizio
SpannungsfUhren
de
Risque de
secousse
Electrical shock
hazard.
Do not open.
No user
serviceable
parts inside.
Refer servicing to
qualified service
personnel.
electrique.
Ne pas ouvrir.
Pas de pieces
reparables par
l'utilisateur.
Entretien par
personnel
Teile.
Nicht offnen.
Enthalt keine vom
Enduerbraucher zu
wartende Teile.
Fur service bitte an
qualifiziertes
repareren
onderdelen.
Door bevoegd
service
personeel
laten repareren
di riparazioni
qualificato.
qualifie.
Service-Personal
wenden.
calificado
Pouches ( 25 per box )
Sign
Poster
Display
3745595 clear 5 mil (W)18.5 x (L)24.5
3745596 clear 5 mil (W) 25 x (L) 37
3745597 clear 5 mil (W) 37 x (L) 49
– Roller Pinch Point: Keep hands and fingers
away. You may be crushed and or burned.
Mounting Boards ( 10 per box )
Poster (white)
Poster (black)
Display (white)
Display (black)
3745571 (W) 25 x (L) 37
CAUTION
WARNUNG
!
!
CUIDADO
!
!
ATTENTION
3745575 (W) 25 x (L) 37
3745572 (W) 37 x (L) 49
3745576 (W) 37 x (L) 49
HOT ROLLS.
HEISSE
ROLLEN
RODILLOS
CALIENTES.
PUNTO DE
PINCHAMIENTO.
Mantener manos
ropa distancia.
ROULEAUX
CHAUDS.
POINT DE
PINCEMENT.
Tenir mains et
PINCH POINT.
Klemmgefahr
zwischen Rollen
Hande und
Keep hands and
clothing away.
y
a
vetements
a
l'ecant.
Kleidung ferhalten
Pouchboards - clear ( 10 per box )
Poster (white)
Poster (black)
Display (white)
Display (black)
3745579 (W) 25 x (L) 37
3745583 (W) 25 x (L) 37
3745580 (W) 37 x (L) 49
3745584 (W) 37 x (L) 49
– Keep clear/ Hot Surface: Keep hands and
fingers away. You may be crushed and or burned.
Pouchboards - sand ( 10 per box )
Poster (white)
Poster (black)
Display (white)
Display (black)
3745587 (W) 25 x (L) 37
3745591 (W) 25 x (L) 37
3745588 (W) 37 x (L) 49
3745592 (W) 37 x (L) 49
WARNING
Serious injury may result.
Keep hand, clothing and loose
articles away from the rollers
and heaters.
CAUTION
Hot surface
Avoid contact
INFORMATION: If similar products are used,
results may differ since temperature and speed is
set for optimal results using GBC products.
Refer to Figure 1.4.1 Safety Label Placement
© 2004 General Binding Corporation
Page 1-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Spartan Operation and Maintenance Manual
Figure 1.4.1 Safety Label Placement
WARNING
Serious injury may result.
Keep hand, clothing and loose
articles away from the rollers
and heaters.
CAUTION
Hot surface
Avoid contact
!
ATTENTION
!
!
WARNUNG
CUIDADO
!
CAUTION
HOT ROLLS.
HEISSE
ROLLEN
RODILLOS
CALIENTES.
PUNTO DE
PINCHAMIENTO.
Mantener manos
ropa a distancia.
ROULEAUX
CHAUDS.
POINT DE
PINCEMENT.
Tenir mains et
PINCH POINT.
Klemmgefahr
zwischen Rollen
Hande und
Keep hands and
clothing away.
y
vetements
a
l'ecant.
Kleidung ferhalten
!
MUCHO
CUIDADO
!
MUCHO
CUIDADO
!
!
!
!
WARNING
WAARSCHUWING
ATTENZIONE
WARNUNG
Riesgo de
choque
electrico
No abra
Adentro, no hay
piezas
reparables
para el usuario.
Mantenimiento
solamente para
personal
Risque de
secousse
electrique.
Ne pas ouvrir.
Pas de pieces
reparables par
l'utilisateur.
Entretien par
personnel
Kans op
elektrische
schok.
Niet openen
Bevatgeen door
gebruik te
Pericolo di
scarica
elettrica.
Nessuna parte
riparabile
dall' utente.
Chiamare un
servizio
SpannungsfUhren
de
Electrical shock
hazard.
Do not open.
No user
serviceable
parts inside.
Refer servicing
to
qualified service
personnel.
Teile.
Nicht offnen.
Enthalt keine vom
Enduerbraucher zu
wartende Teile.
Fur service bitte an
qualifiziertes
repareren
onderdelen.
Door bevoegd
service
personeel
laten repareren
di riparazioni
qualificato.
Service-Personal
wenden.
qualifie.
calificado
!
ATTENTION
!
!
WARNUNG
CUIDADO
!
CAUTION
HOT ROLLS.
HEISSE
ROLLEN
RODILLOS
CALIENTES.
PUNTO DE
ROULEAUX
CHAUDS.
POINT DE
PINCH POINT.
Klemmgefahr
zwischen Rollen
Hande und
PINCHAMIENTO.
PINCEMENT.
Tenir mains et
l'ecant.
Keep hands and
clothing away.
Mantener manos
ropa distancia.
y
a
vetements
a
Kleidung ferhalten
© 2004 General Binding Corporation
Page 1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Spartan Operation and Maintenance Manual
Page 1-4
© 2004 General Binding Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Spartan Operation and Maintenance Manual
DAMAGE OR PERSONAL INJURY ( UNLESS
PRIMARILY CAUSED BY ITS NEGLIGENCE ),
LOSS OF PROFIT OR OTHER INCIDENTAL OR
CONSEQUENTIAL DAMAGES ARISING OUT
OF THE USE OR INABILITY TO USE THE
EQUIPMENT.
2.0 Warranty
GBC Films Group warrants the equipment to be free from
defects in material and workmanship for a period of 90
days for parts and labor from the date of installation.
This warranty is the only warranty made by GBC Films
Group and cannot be modified or amended.
2.2 Exclusions to the Warranty
GBC Films Group’s sole and exclusive liability and
the customer’s sole and exclusive remedy under this
warranty shall be, at GBC Films Group’s option, to
repair or replace any such defective part or product.
These remedies are only available if GBC Films
Group’s examination of the product discloses to
GBC Films Group’s satisfaction that such defects
actually exist and were not caused by misuse,
neglect, attempt to repair, unauthorized alteration
or modification, incorrect line voltage, fire, accident,
flood or other hazard.
This warranty specifically does not cover;
1. Damage to the laminating rolls caused by
knives, razor blades, other sharp objects or
failure caused by adhesives.
2. Damage to the machine caused by lifting, tilting
and/or any attempt to position the machine other
than rolling on the installed castors on even
surfaces.
3. Improper use of the machine.
2.1 Limited Warranty
4. Damage due from unqualified person(s) servicing the
machine.
This warranty specifically does not cover damage to the
laminating rollers caused by knives, razor blades, other
sharp objects, failure caused by adhesives or improper
use of the machine. Warranty repair or replacement does
not extend the warranty beyond the initial 90 day period
from the date of installation.
Qualified;
• Any engineer that has experience with electrical
and mechanical design of lamination equipment. The
engineer should be fully aware of all aspects of safety
with regards to lamination equipment.
CAUTION: Unauthorized customer alterations will
void this warranty.
• Any commissioning or service engineer must be
of competent nature, trained and qualified to GBC Films
Group standards to fulfill that job. This person will have
completed and passed the full service training course from
GBC Films Group.
THE WARRANTY MADE HEREIN IS IN LIEU
OF ALL OTHER WARRANTIES, EXPRESSED
OR IMPLIED, INCLUDING ANY WARRANTY
OR MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE. GBC FILMS GROUP
WILL NOT BE LIABLE FOR PROPERTY
• Any GBC Technician, GBC Specialist, and / or
GBC Films Group Technician that has been through the
GBC Films Group service training course.
© 2004 General Binding Corporation
Page 2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Spartan Operation and Maintenance Manual
This page intentionally left blank.
Page 2-2
© 2004 General Binding Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Spartan Operation and Maintenance Manual
3.3 Electrical
3.0 Specifications
Laminator Rating:
240V, 60 Hz, 2500 W
Description:
Entry level laminator for encapsulation and mounting of
poster size prints. The Spartan is a self standing laminating
unit.
Requirements:
230-240 VAC, 60 Hz, single phase 15 amps.
Features:
Simple one touch operation
BTU Output:
8,535 BTU/Hour
Applications:
Mounting of poster size prints
Encapsulation of poster size prints
Heater Wattages:
2100 watts
Amperage Draw:
Drive motor: 1 amp
Heaters: 9 amps
3.1 Consumable
Material Types:
Thermal mount boards
Thermal pouch boards
Thermal pouches
DC voltage used:
36 VDC motor voltage
Material Widths:
AC voltage used:
38”maximum
230 VAC (minimum)
3.2 Function
3.4 Dimensions and weight
Speed:
Weight:
Preset for GBC materials
Out of box: 250 lbs. (114 kg.)
boxed: 260 lbs. (118 kg.)
Motor:
DC gear motor
Dimensions:
Heating:
Preset for GBC materials
Refer to Figure 3.4.1 Dimensions
assembled:
boxed:
42 in. (H) x 53 in. (W) x 18.5 in. (D)
105 cm (H) x 132 cm (W) x 46 cm (D)
Controls:
Operations control panel
18 in. (H) x 60 in. (W) x 25 in. ( D)
45 cm (H) x 150 cm (W) x 62.5 cm (D)
Roll Design:
High release silicone
Max Working Nip Opening:
3/16 in. (5 cm)
© 2004 General Binding Corporation
Page 3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Spartan Operation and Maintenance Manual
Figure 3.4.1 Dimensions
53 in.
(132 cm)
42 in.
(105 cm)
18.5 in.
(46 cm)
Page 3-2
© 2004 General Binding Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Spartan Operation and Maintenance Manual
4.0 Installation
WARNING: The operating environment must be
free of dust, flammable liquids and vapors. You can
be injured by inhaling chemical vapors.
GBC Films Group is committed to a program of ongoing
product improvement. As a result, we are providing these
instructions so that you can insure that your new Spartan
Laminator is properly and securely unpacked, moved and
installed.
Before a Spartan Laminator can be installed, there are a
few requirements that must be met. Make certain that
each of the requirements listed in the following pre-
installation checklist are met before beginning installation.
WARNING: Vapor build up or stored flammable
liquids can cause a fire. Excessive dust can damage
the laminator.
CAUTION: Do not locate the laminator where air
can blow directly on the machine. The air flow can
cool the rollers unevenly and result in poor quality
output.
CAUTION: Failure to follow the pre-installation
check list can result in damage to the laminator.
4.1 Pre-installation
US and Canada: The laminator requires 230-
240 vac, 60 Hz, 15 amps, single phase
Are the doorways and hallways wide enough for
the laminator to be moved to the installation site?
Figure 4.1.1 Connections-Spartan US
Is there ample room for the laminator?
A work area must be established that allows for
unrestricted movement around the laminator and
provides space for efficient material flow. Figure
4.1.4 and Figure 4.1.5 illustrates a typical machine
area layout.
NEM A 6 - 15P
NEM A 6 - 15R
Is the environment appropriate for the laminator?
Europe: The laminator requires 230-240, 50 Hz
16 amps, single phase
The laminator requires a clean, dust and vapor
free environment to operate properly. It must not
be located where there is air blowing directly on
the machine.
Figure 4.1.2 Connections-Spartan Europe
Have you contacted a certified electrician to install
a receptacle for the laminator ensuring that
adequate power is being supplied and correct
circuit breaker?
16 receptacle
16 plug
© 2004 General Binding Corporation
Page 4-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Spartan Operation and Maintenance Manual
4.2 Suggested floor layout
A safe work area constitutes enough room to work with
the materials at hand while being free to move around the
laminator without interference from the laminator. Refer
to the figure below for a suggested floor layout example.
Figure 4.2.1 Suggest floor layout example
4 ft. x 6 ft.
(101.6 x 152 cm)
8 ft
( 240 cm )
Work table on wheels
Back
Front
18ft.
( 540 ) cm
3 ft
( 90 cm )
4 ft. x 6 ft.
(101.6 x 152 cm)
Work table on wheels
8 ft
( 240 cm )
13 ft
( 390 cm )
Page 4-2
© 2004 General Binding Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Spartan Operation and Maintenance Manual
Under the cover
4.3 Know your laminator
Before performing any procedure within this manual, it is
recommended that you take time to know your laminator.
Cover
raised
Hinge
Rollers
Top Roll
Sensor
Power
switch
Sides of the laminator
Nip
Power cable
Control Panel
SPARTAN
READY
GBC
Parts on the laminator
Cabinet
Roller pressure control
Cover
Table
Pouch rack
Roller release position
Board mount position
Board rack
Stand
Castors
Pouch Position
© 2004 General Binding Corporation
Page 4-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Spartan Operation and Maintenance Manual
4.4 Unpacking
WARNING: Do not attempt to move the laminator
across anything other than a flat level surface alone.
You can be crushed or seriously injured.
INFORMATION: All shipments are ex-works. At
our docks, title passes to the buyer. Please review
your insurance coverage prior to shipment, as you
are responsible for all subsequent freight charges
and risks.
WARNING: Do not turn the laminator sideways, up
side down or vertical when moving. This will disrupt
the alignment of internal moving parts.
INFORMATION: Before signing the Bill of Lading,
be sure to inspect the crate, box and/ or pallet for
signs of damage or missing items. If applicable, make
note of this on the Bill of lading.
1.Inspect the machine for any obvious shipping damages
upon receipt.
2. Carefully unwrap the shrink wrap from around the
laminator.
CAUTION: Do not use a knife or other sharp object
to remove any shrink wrap from around the
laminator. You can cause irreparable damage to the
rollers!
3. With another person, carefully remove the contents
and assemble the laminator.
4. With assistance, carefully move the laminator to the
desired location.
Page 4-4
© 2004 General Binding Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Spartan Operation and Maintenance Manual
RUN – When pressed, engages the motor that
drives the rollers.
5.0 Operations
WARNING: Do not wear ties, loose fitting clothes
or dangling jewelry while operating or servicing the
laminator. These items can get caught in the nip and
choke you or you can be crushed or burned.
INFORMATION: The laminator only operates in
one direction, forward. There is no reverse function
on this machine. Stop the roller and release roller
pressure to manually move the product backwards.
CAUTION: Do not block the Top Roll Sensor. If
the sensor becomes obstructed, over heating may
occur and cause irreparable damage to the rollers
or a fire.
STOP – When pressed, stops the roller by
removing power to the motor.
READY – When illuminated, represents the rollers
are up to operating temperature.
INFORMATION: The laminator will only run when
the roller cover is in the down (closed) position.
INFORMATION: Do not run material until READY
is illuminated. Attempting to run prior to this will
result in poor output quality.
5.1 Control Panel
The control panel is located on the right hand side from
the front operating position of the laminator. From the
control panel, the operator is able to control the motor
run and motor stop function.
RUN – when illuminated, represents the motor
engaged and the rollers are turning.
Figure 5.1.1 Control panel
SPARTAN
READY
GBC
INFORMATION: The motor will only engage if the
cover is in the lowered position.
Ready indicator
Run indicator
Run switch
Stop switch
WARNING: Never attempt to bypass the cover
safety switch to operate the laminator. This can result
in serious injury to you or others.
© 2004 General Binding Corporation
Page 5-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Spartan Operation and Maintenance Manual
Laminating position
5.2 Roller pressure handle
The roller pressure handle sets the roller nip opening for
the desired application with the material being used.
INFORMATION: Never attempt to alter the
factory preset settings for the nip opening or speed.
Contact your local service representative if you feel
the roller pressure handle requires calibrating.
–Usethispositionwhenrunningfilmpouchtypematerials.
Theistheminimumnipopeningposition. Thisnipopening
and speed is preset for GBC materials.
Roller release position
5.3 ON/ OFF power switch
The power ON/ OFF turns your laminator on. When the
laminator is on, the rollers begin heating automatically.
–Use this position when the laminator is not in use or no
nip pressure is required. This is the maximum nip opening
position.
(–) This is the ON position for the laminator.
(O) This is the OFF position for the laminator.
Foam pouch position
CAUTION: During long periods of no use, 30
minutes or greater, you should turn power off to the
laminator. This will prevent hot spots from forming
on the rollers.
–Usethispositionwhenusingboardtypematerialsthrough
the laminator. This nip opening and speed is preset for
GBC materials.
Page 5-2
© 2004 General Binding Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Spartan Operation and Maintenance Manual
5. Press RUN.
6.0 Applications
+
The Spartan laminator will accommodate GBC mounting
boards and lamination pouches. This section will describe
how each process is run on the laminator.
6. Align the leading edge of the pouch board slightly off
center of the table.
INFORMATION: The leading edge will always be
the edge which is sealed. The opposite edge is
referred to as the trailing edge.
CAUTION: When changing from one application to
another (example: lamination pouch to pouch
boards), allow the machine to run for approx. 20 min
after setting pressure handle to let the roller
tempurature reach correct operating tempurature.
The top roll sensor only reads the top roll and the
bottom roll may not be the correct tempurature.
7. Gently slide the pouch board into the roller nip until
you feel the rollers catch the board.
8. Support the board as it exits the rear of the laminator.
6.1 Pouch boards
1. Turn the laminator on.
9. Press STOP and set the pressure handle to the roller
release position.
2. Center the image on the board under the film.
Film
Image
Board
+
3. Set the pressure handle to the foam pouch position.
10. Peel the clear protective layer off the board and trim
to desired size.
4. Wait for READY to illuminate.
Clear protective layer
© 2004 General Binding Corporation
Page 6-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Spartan Operation and Maintenance Manual
6.2 Mounting boards
7. Gently slide the mounting board into the roller nip until
you feel the rollers catch the board.
1. Turn the laminator on.
8. Support the board as it exits the rear of the laminator.
2. Center the image on the board under the protective
sheet.
Protective sheet
Image
Board
9. Press STOP and set the pressure handle to the roller
release position.
3. Set the pressure handle to the foam pouch position.
+
10. Pull the protective layer off the board and trim to
desired size.
4. Wait for READY to illuminate.
5. Press RUN.
Protective layer
+
6. Align the leading edge of the mounting board slightly
off center of the table.
Page 6-2
© 2004 General Binding Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Spartan Operation and Maintenance Manual
6.3 Lamination pouches
6. Wait for READY to illuminate.
7. Press RUN.
+
INFORMATION: Treat the pouch carriers carefully
as they may be reused until you see wrinkles in the
lamination.
8. Align the leading edge of the pouch carrier containing
the lamination pouch and image slightly off center of the
table.
1. Turn the laminator on.
2. Center the lamination pouch between the two sheets
of the pouch carrier.
Pouch carrier
Lamination
pouch
9. Gently slide the pouch carrier into the roller nip until
you feel the rollers catch the pouch carrier.
3. Fold the top sheet of the pouch carrier and the
lamination pouch over.
10. As the pouch carrier nears its end, be prepared to
catch the pouch carrier as it exits the rear of the laminator.
4.Center the image on the lamination pouch and carefully
lay the top sheets back over the image.
Pouch carrier
Lamination pouch
Image
11. Press STOP and set the pressure handle to the roller
release position.
5. Set the pressure handle to the lamination position.
+
© 2004 General Binding Corporation
Page 6-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Spartan Operation and Maintenance Manual
• Laminated pouch output has a tendency to become
wavy when excess film to film lamination is left on the
outer parameter of the image being laminated. When
trimmed to the edge of the sheet, the output should be
flat. As the amount of film to film lamination increases,
the qualitiy of the output decreases.
12. Remove the laminated image from the pouch carrier
and trim to desired size.
Pouch carrier
Laminated
image
6.4 Helpful Hints
Thefollowinghintswillhelpyougetthebestpossibleoutput
from your Spartan laminator:
Pouch Boards:
• It is critical that at the leading edge, the film is evenly
secured to the board. If the corners are dented or
chrushed, cut the damaged part off to prevent wrinkles
and waves.
• If switching from lamination pouches to pouch boards,
wait for the bottom roller to cool before running boards
(approx. 20 min). A hot bottom roller will bubble the
back of the board. To speed the cooling process, a
scrap board may be run through the machine 2-3 times
to help cool the bottom roller.
Laminating Pouches:
• To reduce waving affect, match the size of the pouch as
close to the image size as possible. This will allow the
stresses on the envelope to be more even, resulting in a
smoother laminated image.
• Some substrates will be affected by the heat and stress
of the laminating pouch to different degrees. Trimming
the image as close to the edge as possible can reduce
waving in the image.
• It is recommended to prepare the envelope on a
separate table away from the heated rollers as the image
can be damaged if the front edge is heated before all
parts of the envelope are smoothed out.
Page 6-4
© 2004 General Binding Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Spartan Operation and Maintenance Manual
7.1 Cabinets, cover and stand
7.0 Maintenance
GBCFilmsGrouplaminatorsrequireminimalmaintenance.
However, regular maintenance is essential to keep any
piece of precision machinery at peak performance. A
maintenance schedule and a section of procedures are
included in this section.
ELECTRICAL HAZARD: Remove power from the
laminator before cleaning. You can be severely
shocked, killed or cause a fire.
1. Use a damp ( use water only to dampen the cloth )
white terry cloth towel to wipe dust from the cabinets,
cover and stand.
WARNING: Do not wear ties, loose fitting clothes
or dangling jewelry while operating or servicing the
laminator. These items can get caught in the nip and
choke you or you can be crushed or burned.
7.2 Rollers
INFORMATION: Improper maintenance can result
in poor output quality.
CAUTION: Never clean the rollers with sharp or
pointed objects. You may put irreparable cuts into
the rollers.
GBC offers Cleaning kits ( P/N 1711515 ) as well as
Extended Maintenance Agreements.
INFORMATION: Power is required to rotate the
rollers which means heat will be present as well.
The only maintenance required by the operator is to
maintain clean and adhesive free nip rollers and overall
cleanliness of the laminator itself.
7.2.1 Stains/ dust on rollers
ELECTRICAL HAZARD: Do not use liquid or
aerosol cleaners on the laminator. Do not spill liquid
of any kind on the laminator. You can be severely
shocked, killed or cause a fire. Use only a damp cloth
for cleaning unless other wise specified.
CAUTION: The following procedure is performed
while the laminator is HOT! Use extreme caution!
© 2004 General Binding Corporation
Page 7-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Spartan Operation and Maintenance Manual
1. Set the pressure handle to the roller release position 1. Set the pressure handle to the roller release position
and raise the cover.
and raise the cover.
2. Use a damp ( use water only to dampen the cloth ) 2. With a rubber cement eraser or Scotch Brite TM gently
white terry cloth towel to wipe dust from the upper roller. rub the adhesive on the roller.
3. For the lower roller, close the cover, press RUN to
rotate the lower roller to a new area to clean.
CAUTION: Excessive pressure can destroy the
silicone layer by pressing too hard or scrubbing too
long in one spot.
4.Repeat the steps above until the lower roller is cleaned
7.2.2 Adhesive on rollers
3. Use a damp (water only) white terry cloth towel to
wipe adhesive beads off the roller.
4. For the lower roller, close the cover, press RUN to
rotate the lower roller to a new area to clean.
CAUTION: Hardened adhesive deposits on the
rollers can cause damage to the rollers.
5.Repeat the steps above until the lower roller is cleaned
CAUTION: Do NOT pick or pull heat activated
adhesive off the rolls when they are cold. You can
cause irreparable damage to the laminating rolls.
CAUTION: The following procedure is performed
while the laminator is HOT! Use extreme caution!
Page 7-2
© 2004 General Binding Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
General Binding Corporation
One GBC Plaza
Northbrook, IL 60062-4195
Download from Www.Somanuals.com. All Manuals Search And Download.
|