Fujitsu Tablet FMW4503TS128A01 User Manual
TM  
Stylistic 3500  
Technical  
Reference  
Guide  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table of Contents  
About This Guide ...........................................................................................................................  
viii  
viii  
ix  
Organization ....................................................................................................................................................  
Related Documentation .................................................................................................................................  
Technical Support ...........................................................................................................................................  
x
Chapter 1  
Pen Tablet Features ........................................................................................................................  
PC Card Support .............................................................................................................................................  
Internal LAN/ Modem ...................................................................................................................................  
ACPI Support ..................................................................................................................................................  
1
1
1
1
Chapter 2  
System Software ..............................................................................................................................  
Supported Operating Systems ......................................................................................................................  
Pen Support .....................................................................................................................................................  
PC Card Support .............................................................................................................................................  
Overview of System Configuration Tools and Utilities ............................................................................  
2
2
2
2
2
Chapter 3  
Configuring the Stylistic 3500 Pen Tablet System ...................................................................  
Pen Configuration...........................................................................................................................................  
Pen Subsystems ...............................................................................................................................................  
Permanent and Current BIOS Settings ........................................................................................................  
BIOS Setup .......................................................................................................................................................  
Starting BIOS Setup ............................................................................................................................  
Using BIOS Setup ................................................................................................................................  
Exiting BIOS Setup..............................................................................................................................  
BIOS Setup Main Menu Options ......................................................................................................  
Primary Master Submenu Options ..................................................................................................  
Advanced Menu Options ..................................................................................................................  
Serial/ Parallel Port Configuration Submenu Options ..................................................................  
Keyboard/ Mouse Features Submenu Options ..............................................................................  
Video Submenu Options....................................................................................................................  
Internal Device Configurations Submenu.......................................................................................  
PCI Configuration Submenu .............................................................................................................  
CPU Features Submenu .....................................................................................................................  
Event Logging Submenu ...................................................................................................................  
Security Menu Options ......................................................................................................................  
Hard Disk Security Submenu ...........................................................................................................  
Owner Information Submenu ...........................................................................................................  
Power Menu Options .........................................................................................................................  
Advanced Features Options Submenu ............................................................................................  
Boot Menu Options.............................................................................................................................  
Boot Device Priority Submenu..........................................................................................................  
Info Menu .............................................................................................................................................  
Exit Menu Options..............................................................................................................................  
Using CMOSRDWR........................................................................................................................................  
Saving a BIOS Configuration Using CMOSRDWR .......................................................................  
Restoring a BIOS Configuration .......................................................................................................  
PHDISK Hard Disk Preparation Utility ......................................................................................................  
Command Line Options ...................................................................................................................  
CREATE Option ................................................................................................................................  
Automatic Memory Size Calculation ..............................................................................................  
4
4
4
4
5
5
6
7
8
9
10  
11  
13  
14  
15  
16  
17  
17  
18  
20  
20  
21  
23  
24  
24  
25  
25  
26  
26  
26  
27  
27  
28  
29  
iii  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specify Memory Size.........................................................................................................................  
/PARTITION or /P ...........................................................................................................................  
/FILE or /F .......................................................................................................................................  
/CREATE Option Syntax .................................................................................................................  
REFORMAT Option .........................................................................................................................  
/REFORMAT Option Syntax ............................................................................................................  
DELETE Option .................................................................................................................................  
/DELETE Option Syntax...................................................................................................................  
INFO Option .....................................................................................................................................  
/INFO Option Syntax.........................................................................................................................  
Messages ............................................................................................................................................  
PHDISK Sign-on Message ................................................................................................................  
Help Screen ......................................................................................................................................  
Unrecognized Option .......................................................................................................................  
Fatal Error..........................................................................................................................................  
Not Enough Disk Space.....................................................................................................................  
Save to Disk Partition Exists .............................................................................................................  
Too Many Bad Sectors ....................................................................................................................  
First Two Sectors Bad........................................................................................................................  
PHDISK /CREATE Failed to Execute ..............................................................................................  
Good Sector Map Corrupted..............................................................................................................  
Not Enough System Memory ............................................................................................................  
File Already Exists ..........................................................................................................................  
29  
29  
29  
30  
30  
30  
31  
31  
31  
31  
32  
32  
32  
32  
32  
32  
33  
33  
33  
33  
33  
34  
34  
Chapter 4  
Installing Hardware Options .......................................................................................................  
Installing a PC Card........................................................................................................................................  
Removing a PC Card ......................................................................................................................................  
Installing a DIMM Card .................................................................................................................................  
Removing a DIMM Card ...............................................................................................................................  
35  
35  
36  
36  
37  
Chapter 5  
Hardware Specifications ...............................................................................................................  
General Specifications ....................................................................................................................................  
Display Specifications ....................................................................................................................................  
External Video Capabilities ...........................................................................................................................  
Digitizer Specifications ..................................................................................................................................  
Technology Notice ..............................................................................................................................  
Peripheral Interface Specifications ...............................................................................................................  
Power System Specifications.........................................................................................................................  
Environmental Specifications........................................................................................................................  
Physical Specifications ...................................................................................................................................  
Agency Approval Specifications ..................................................................................................................  
Internal LAN/ Modem Specifications ..........................................................................................................  
Port Replicator/ Mini-Dock Specifications ..................................................................................................  
38  
38  
39  
39  
40  
40  
41  
42  
43  
43  
43  
44  
46  
Chapter 6  
Peripheral Interfaces ......................................................................................................................  
High Usage Contacts ......................................................................................................................................  
Serial Port .........................................................................................................................................................  
DC Power Input .............................................................................................................................................  
Floppy Disk Drive Port ..................................................................................................................................  
Universal Serial Bus Port ...............................................................................................................................  
System Interface Port......................................................................................................................................  
IrDA Port..........................................................................................................................................................  
Audio Jacks ......................................................................................................................................................  
PC Card Port....................................................................................................................................................  
Hard Disk Drive Port .....................................................................................................................................  
47  
47  
48  
48  
49  
50  
51  
59  
59  
61  
64  
iv  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 7  
System Power ..................................................................................................................................  
System Power Hardware ...............................................................................................................................  
Battery Pack .........................................................................................................................................  
DC Power Inputs.................................................................................................................................  
66  
66  
66  
67  
Chapter 8  
BIOS Configuration Application Programming Interfaces ...................................................  
Version Information .......................................................................................................................................  
Summary of Functions ...................................................................................................................................  
InitializeBIOS...................................................................................................................................................  
UpdateBIOSCheckSum ..................................................................................................................................  
ReadBIOSSettings ...........................................................................................................................................  
BiosSetupSet ....................................................................................................................................................  
Error Codes ......................................................................................................................................................  
Option and Setting Parameters.....................................................................................................................  
68  
68  
68  
69  
69  
69  
69  
70  
70  
Chapter 9  
Programmable Hotpad Libraries for Windows Applications ................................................  
Hotpad Notification........................................................................................................................................  
SetHotpadNotification ...................................................................................................................................  
KillHotpadNotification ..................................................................................................................................  
73  
73  
74  
74  
Appendix A  
Replacing the IDE Hard Disk Drive ...........................................................................................  
Removing the Hard Disk Drive ....................................................................................................................  
Installing the Hard Disk Drive......................................................................................................................  
75  
75  
78  
Appendix B  
AT Command Set ............................................................................................................................  
AT Commands Table......................................................................................................................................  
AT Data Commands...........................................................................................................................  
AT Fax (Class1) Commands..............................................................................................................  
V.25ter AT Commands.......................................................................................................................  
S Register Table ...............................................................................................................................................  
Result Codes Summary..................................................................................................................................  
79  
80  
80  
85  
86  
87  
90  
Appendix C  
Agency Notices ................................................................................................................................  
FCC Notices .....................................................................................................................................................  
DOC (Industry Canada) Compliance Notices ............................................................................................  
92  
92  
93  
v
Download from Www.Somanuals.com. All Manuals Search And Download.  
List of Figures  
Figure 3-1  
Figure 4-1  
Figure 4-2  
Figure 4-3  
Figure 6-1  
Figure 6-2  
Figure 6-3  
Figure A-1:  
Figure A-2:  
Figure A-3:  
Figure A-4:  
Figure A-5:  
BIOS Setup Screen...............................................................................................................................  
6
Installing a PC Card ............................................................................................................................  
Installing a DIMM Card ......................................................................................................................  
Removing a DIMM Card ....................................................................................................................  
System Interface Port Connector (On Pen Tablet) ..............................................................................  
PC Card Port Configuration ................................................................................................................  
Hard Disk Drive Pin Locations ...........................................................................................................  
IDE Hard Disk Drive Cover Plate........................................................................................................  
Unplugging the Hard Disk Drive Connector .......................................................................................  
Removing the Hard Disk Drive, Part 1 ................................................................................................  
Removing the Hard Disk Drive, Part 2 ................................................................................................  
Installing the IDE Hard Disk Drive .....................................................................................................  
35  
36  
37  
51  
61  
64  
75  
76  
77  
77  
78  
vi  
Download from Www.Somanuals.com. All Manuals Search And Download.  
List of Tables  
Table 3-1.  
Table 3-2.  
Table 3-3.  
Table 3-4.  
Table 3-5.  
Table 3-6.  
Table 3-7.  
Table 3-8.  
Table 3-9.  
Table 3-10.  
Table 3-11.  
Table 3-12.  
Table 3-13.  
Table 3-14.  
Table 3-15.  
Table 3-16.  
Table 3-17.  
Table 3-18.  
Table 3-19.  
Table 3-20.  
Table 3-21.  
Table 3-22.  
Table 3-23.  
Table 3-24.  
Table 5-1.  
Table 5-2.  
Table 5-3.  
Table 5-4.  
Table 5-5.  
Table 5-6.  
Table 5-7.  
Table 5-8.  
Table 5-9.  
Table 5-10.  
Table 5-11.  
Table 6-1.  
Table 6-2.  
Table 6-3.  
Table 6-4.  
Table 6-5.  
Table 6-6.  
Table 6-7.  
Table 6-8.  
Table 6-9.  
Table 6-10.  
Table 6-11.  
Table 7-1.  
Table 8-1.  
Table 8-2.  
BIOS Setup Main Menu Options .........................................................................................................  
8
9
BIOS Setup Primary Master Configuration Options ...........................................................................  
BIOS Setup Advanced Menu Options .................................................................................................  
Serial/Parallel Port Configurations Submenu Options.........................................................................  
Keyboard/Mouse Features Submenu Options......................................................................................  
Video Features Submenu Options........................................................................................................  
Internal Device Configurations Submenu Options ..............................................................................  
PCI Configuration Submenu Options ..................................................................................................  
CPU Features Submenu Options..........................................................................................................  
Event Logging Submenu Options ........................................................................................................  
BIOS Setup Security Menu Options ....................................................................................................  
Hard Disk Security Submenu Options ................................................................................................  
Owner Information Submenu Options.................................................................................................  
BIOS Setup Power Savings Options....................................................................................................  
BIOS Advanced Features Options Submenu ......................................................................................  
BIOS Setup Boot Menu Options..........................................................................................................  
BIOS Setup Boot Sequence Submenu .................................................................................................  
BIOS Setup Info Menu.........................................................................................................................  
BIOS Setup Exit Menu Options...........................................................................................................  
PHDISK Command Line Options........................................................................................................  
PHDISK /CREATE Option..................................................................................................................  
PHDISK /REFORMAT Option ...........................................................................................................  
PHDISK /DELETE Option..................................................................................................................  
PHDISK /INFO Option........................................................................................................................  
Logic System Specifications................................................................................................................  
Display Specifications..........................................................................................................................  
Supported Video Modes for External Monitors...................................................................................  
Digitizer Specifications ......................................................................................................................  
Peripheral Interface Specifications.......................................................................................................  
Power System Specifications ...............................................................................................................  
Environmental Specifications ..............................................................................................................  
Stylistic 3500 Pen Tablet Specifications..............................................................................................  
Agency Approval Specifications..........................................................................................................  
Internal LAN/Modem Specifications...................................................................................................  
Stylistic 3500 Port Replicator/Mini-Dock Specifications....................................................................  
Metal Contacts .....................................................................................................................................  
Serial Port Connector Pin Assignments ...............................................................................................  
DC Power Input Connector Pin Assignments......................................................................................  
Floppy Disk Drive Connector Pin Assignments ..................................................................................  
Universal Serial Bus Port Contact Pin Assignments............................................................................  
System Interface Port Connector Pin Assignments .........................................................................  
IrDA Port Specifications......................................................................................................................  
Active Audio Inputs .............................................................................................................................  
Active Audio Outputs ..........................................................................................................................  
PC Card Port Pin Assignments ............................................................................................................  
Hard Disk Drive Pin Assignments .......................................................................................................  
DC Input Connectors............................................................................................................................  
BIOS Configuration API Error Codes .................................................................................................  
Option and Setting Parameters and Return Values..............................................................................  
10  
11  
13  
14  
15  
16  
17  
17  
18  
20  
20  
21  
23  
24  
24  
25  
25  
27  
30  
30  
31  
31  
38  
39  
39  
40  
41  
42  
43  
43  
43  
44  
46  
47  
48  
48  
49  
50  
52  
59  
59  
60  
61  
64  
67  
70  
70  
vii  
Download from Www.Somanuals.com. All Manuals Search And Download.  
About This Guide  
This guide provides technical information on the Fujitsu Stylistic 3500 pen tablet computer for  
technicians, hardware developers, and software developers.  
Organization  
0
This guide is organized as follows:  
• Chapter 1: Pen Tablet Features  
This chapter discusses some of the system’s main features and technology.  
• Chapter 2: System Software  
This chapter gives an overview of system software and utilities preinstalled on the Stylistic 3500 pen  
tablet.  
• Chapter 3: Configuring the Stylistic 3500 Pen Tablet System  
This chapter provides details on using BIOS Setup and other configuration utilities for the Stylistic  
3500 pen tablet. BIOS configuration options are explained in detail.  
• Chapter 4: Installing Hardware Options  
This chapter gives detailed instructions on installing hardware options such as PCMCIA Cards and  
DIMM cards. (For instructions on replacing the internal hard disk drive, see “Replacing the IDE Hard  
Disk Drive” on page 75.)  
• Chapter 5: Hardware Specifications  
This chapter gives hardware specifications on the pen tablet system. Industry standards supported by  
the Stylistic 3500 pen tablet are listed.  
• Chapter 6: Peripheral Interfaces  
This chapter provides details on peripheral interfaces provided by the Stylistic 3500 pen tablet and the  
Stylistic 3500 port replicator and mini-dock.  
• Chapter 7: System Power  
This chapter provides information on the pen tablet’s system power hardware.  
• Chapter 8: BIOS Configuration Application Programming Interfaces  
This chapter gives details on using DLLs which allow you to configure the Stylistic 3500 BIOS.  
• Chapter 9: Programmable Hotpad Libraries for Windows Applications  
This chapter provides information on using the programmable hotpad with 32-bit Windows  
applications.  
• Appendix A: Replacing the IDE Hard Disk Drive  
This appendix provides instructions on removing and replacing the system’s built-in IDE hard disk  
drive.  
• Appendix B: AT Command Set  
This appendix provides a detailed list of AT commands used by the pen tablet’s modem, including AT  
Commands, S Register Table, and Result Codes Summary information.  
• Appendix C: Agency Notices  
This appendix states notices required by regulatory agencies in the United States and Canada that  
apply to the Stylistic 3500.  
viii  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Related Documentation  
0
Documentation relating to the Stylistic 3500 pen tablet system is listed below. Refer to these documents  
for details on topics not covered in this guide.  
Stylistic 3500 User’s Guide  
This guide provides an introduction to the Stylistic 3500 pen tablet’s basic functions for the end user.  
Stylistic 3500 Mini-Dock User’s Guide  
This guide gives instructions on using the Stylistic 3500 mini-dock.  
The following documents, available from retail book sellers, contain additional information about  
software preinstalled on the Stylistic 3500 pen tablet.  
Microsoft Windows 98 Resource Kit (ISBN: 1-57231-644-6)  
This manual is a technical guide for installing, configuring, and supporting Windows 98 and is  
published by Microsoft Press, 1-800-MSPRESS in the U.S. as well as from retail book sellers.  
Microsoft Windows 2000 Professional Resource Kit (ISBN 1-57231-808-2)  
This manual is a technical guide for installing, configuring, and supporting Windows 2000  
Professional and is published by Microsoft Press, 1-800-MSPRESS in the U.S. as well as from retail  
book sellers.  
Microsoft Windows NT: Workstation Resource Kit (ISBN 1-57231-343-9)  
This manual is a technical guide for installing, configuring, and supporting Windows NT 4.0  
Workstation and is published by Microsoft Press, 1-800-MSPRESS in the U.S. as well as from retail  
book sellers.  
The following resources contain information on software development tools for Windows:  
Microsoft Developer’s Network  
The Microsoft Developer’s Network web site provides links to information on application  
programming interfaces (APIs) used with Microsoft Windows. The site address is  
<MSDN.Microsoft.com>.  
The following documents provide information on industry standards supported by the Stylistic 3500  
pen tablet system.  
Advanced Configuration and Power Interface (ACPI) Specification, Revision 1.0  
The ACPI was developed by Microsoft, Intel, and Toshiba to manage device control in order to  
conserve power. The ACPI specification and additional detailed information is available at the ACPI  
web site, <http:/ / www.teleport.com/ ~acpi/ >.  
PC Card Standards  
The Stylistic 3500 pen tablet and supporting system software comply with PCMCIA and PC Card  
standards specifications up to and including the PC Card Standard February 1995 (also referred to as PC  
Card Standard Release 3.0 in this document and other related documentation). PC Card standards are  
published by: Personal Computer Memory Card International Association, 2635 North First Street,  
Suite 209, San Jose, CA 95131, <http:/ / www.pc-card.com/ >, (408) 433-CARD (2273).  
IrDA Standards  
The IrDA port on the Stylistic 3500 pen tablet is compliant with IrDA (Infrared Data Association)  
Standard Version 1.1 published by: Infrared Data Association, <http:/ / www.irda.org>, (510) 943-6546.  
Universal Serial Bus Specification  
The Universal Serial Bus (USB) ports on the Stylistic 3500 pen tablet and docking peripherals are  
compliant with the Universal Serial Bus Specification Version 1.0. Refer to this specification for USB  
Related Documentation  
ix  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
details including: cable requirements, topology, and USB power distribution. This specification and  
other technical documents regarding USB are available on the Universal Serial Bus Implementer’s  
Forum home page at <http:/ / www.usb.org/ >.  
Desktop Management Interface (DMI) 2.0 Specification  
The Stylistic 3500 BIOS supports DMI. The DMI specification and other information relating to DMI  
are available on the Desktop Management Task Force web site at <http:/ / www.dmtf.org/ >.  
Technical Support  
0
For technical support on the Stylistic 3500 pen tablet system, Fujitsu Resellers (VARs) should contact your  
assigned Fujitsu PC Systems Engineer or contact Fujitsu PC Technical Support at 1-800-831-3183 during  
normal business days from 7:00 to 4:00 Pacific Time. (Voice mail is available at this number during  
non-business hours.)  
Technical Support  
x
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Chapter 1  
Pen Tablet Features  
This chapter provides an introduction to the Stylistic 3500 pen tablet system hardware and gives an  
overview of some of the pen tablet system’s features. Detailed specifications on the features discussed in  
this chapter are given in other chapters of this guide.  
The Stylistic 3500 pen tablet computer is designed for the Windows 98 Second Edition, Windows NT  
Workstation 4.0, and Windows 2000 Professional operating systems. The system uses an resistive pen  
digitizer and is available with either an indoor color thin-film-transistor (TFT) display or an indoor/  
outdoor color TFT display.  
The Stylistic 3500 pen tablet system has been tested by Windows Hardware Quality Labs (WHQL) at  
Microsoft Corporation and is compliant with PC 99 system design guidelines.  
PC Card Support  
1
The Stylistic 3500 pen tablet is equipped with a PC Card slot that allows you to install a Type II PC Card.  
The PC Card slot is compliant with PC CardBus Standard Release 3.0 and provides support for the  
following PC Card features:  
• Multivoltage 3.3/ 5 V PC Cards (detected automatically)  
• CardBus (PCI bridge) type PC Cards  
• Supports PCIC (PC Card I/ O Card) protocol  
• Backward compatibility with previous PC Card Standard Release level PC Cards  
Internal LAN/Modem  
1
Stylistic 3500 pen tablet systems are equipped with an internal LAN/ 56 Kbps* modem. For details on the  
built-in LAN/ modem, see “Internal LAN/ Modem Specifications” on page 44.  
ACPI Support  
1
The Stylistic 3500 pen tablet supports the Advanced Configuration and Power Interface (ACPI) Specification,  
revision 1.0, in all system configurations except Windows NT 4.0; the Windows NT 4.0 operating system  
does not utilize ACPI or APM design specifications.  
* The 56 Kbps rate is nominal; due to FCC restrictions, actual rates are limited to 53 Kbps.  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
                     
Chapter 2  
System Software  
This chapter outlines system software supported on the Stylistic 3500 pen tablet including operating  
system software, and drivers and utilities developed specifically for the Stylistic 3500 pen tablet system.  
Supported Operating Systems  
2
The Stylistic 3500 pen tablet is distributed with one of the following operating systems preinstalled:  
• Windows 98  
• Windows NT Workstation 4.0 (Build 1381, SP 6a)  
• Windows 2000  
Licensing and user documentation for the operating system installed on your system is also included  
with the pen tablet. For details on the operating system, refer to the documentation provided, or refer to  
the documents listed in “Related Documentation” in the About This Manual section of this guide.  
Note: MS-DOS is not supported as an end-user operating environment. Support for MS-DOS is limited to the  
use of configuration and other support utilities designed for the Stylistic 3500 pen tablet system.  
Pen Support  
2
Pen support for the Stylistic 3500 pen tablet is provided by the following three pen subsystems:  
• Microsoft Pen Services 2.0 with CIC HRS 5.0.5 (Windows 98 only)  
• CIC PenX 2.02 (All systems)  
• Mouse Emulation (All systems)  
You can select one of these subsystems “on the fly” using the pen configuration control panel applet. See  
“Pen Configuration” on page 4 for details. (Software for all of these subsystems runs at the same time.  
Pen information is routed to the selected subsystem.)  
Pen drivers (developed by Fujitsu PC Corporation) for the Stylistic 3500 support the pen digitizer system  
as a Plug and Play (PnP) device. To view information on these pen drivers, open Pen Configuration in  
Control Panel and choose the About tab. Select the desired file from the list and choose File Info.  
PC Card Support  
2
The Stylistic 3500 pen tablet fully supports the PC Card standard release 3.0. System resources for PC  
Cards are configured automatically by Windows 98 and Windows 2000.  
Phoenix/ Softex Card Executive 2.0 for Windows NT is preinstalled on Windows NT systems to provide  
PC Card support. Refer to the on-line help provided with Phoenix/ Softex Card Executive for details on  
supported PC Cards.  
Overview of System Configuration Tools and Utilities  
2
The following system configuration tools and utilities are supported for use with the pen tablet. Unless  
otherwise noted, details on using these programs are given in Chapter 3 of this manual.  
Supported Operating Systems  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
                                   
• BIOS Setup (Fujitsu BIOS Configuration)  
A BIOS configuration utility stored in the system’s CMOS memory.  
• Handwriter Settings  
A control panel applet that allows you to configure settings for handwriting recognition and inking.  
• Pen Configuration  
A control panel applet that allows you to select the pen subsystem, calibrate the pen, and configure  
pen settings.  
• PHDISK (Windows 98 and Windows NT only)  
A utility used to prepare your hard disk for using save-to-disk suspend mode.  
• CMOS REad/ Write Utility  
A utility that allows you to read the system BIOS CMOS contents into a specified file, then write the  
file contents back into an identical system that has the same BIOS version.  
Overview of System Configuration Tools and Utilities  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Chapter 3  
Configuring the Stylistic 3500 Pen Tablet System  
This chapter provides instructions on how to use various configuration utilities to configure the Stylistic  
3500 pen tablet BIOS.  
Pen Configuration  
3
Windows 98 and Windows 2000 systems include a pen configuration control panel applet which allows  
you to select the pen subsystem, configure pen buttons, and calibrate the pen. To use this applet, open  
Pen Configuration in Control Panel and select the desired tab as follows:  
• Pen Subsystem (Windows 98 only)  
Allows you to choose the active pen subsystem and apply your changes “on the fly”. See “Pen  
Subsystems” for more information.  
• Pen Buttons (Windows 98 only)  
Allows you to configure the functions and behavior of the pen. The Stylistic 3500 has a resistive  
digitizer, but the Pen Buttons tab allows you to emulate a pen tip button and pen barrel button, as  
used with an electromagnetic digitizer. The Pen Buttons tab is used in conjunction with the Right  
Mouse hotpad.  
• Calibration  
Allows you to calibrate the pen digitizer system.  
• Sampling (Windows 98 only)  
Displays the resolution of the pen (sampling rate in point per second).  
• About  
Allows you to view file information about the installed pen drivers.  
• Hovering  
Used in conjuction with the Hovering hotpad to allow you to modify the behavior of pen tap  
sequences.  
For details on each of these features, tap the Help button for each tab.  
Pen Subsystems  
3
3
(Windows 98 only) The Stylistic 3500 supports the following pen subsystems: Pen X, Pen Windows, or  
Emulate Mouse. You choose one of these subsystems using the Pen Configuration Control Panel applet,  
as described earlier.  
Note: Training utilities work only for the specific pen subsystem. Tutorials such as Handwriting Trainer for Pen  
Windows and Handwriter Tutorial for Pen X can only be used when the correct pen subsystem is selected.  
Permanent and Current BIOS Settings  
Some BIOS configuration utilities allow you to select permanent and/ or current settings when  
configuring BIOS options. When you change a permanent setting, BIOS parameters stored in CMOS  
memory are changed and the new setting is applied after the system is restarted. When you change a  
current setting, BIOS parameters stored in dynamic memory are changed and the new setting is applied  
for the current session. Also, note that a change to the current setting only remains in effect until the  
system is restarted or shut down.  
Pen Configuration  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
                                       
BIOS data resides in the system’s CMOS memory. When the system is powered on, BIOS data is copied or  
“shadowed” into the system’s dynamic memory and the system runs using BIOS parameters stored in  
dynamic memory.  
BIOS Setup  
3
BIOS Setup is a configuration utility that you can use to change your system’s permanent BIOS settings.  
The BIOS Setup application is stored in the BIOS flash ROM. (BIOS Setup values or settings are stored in  
CMOS memory.) Instructions for starting and running BIOS Setup are given in the following discussions.  
Starting BIOS Setup  
3
To start BIOS Setup, restart your system and when the following message is displayed,  
<F2>,Doubletapthepen+:BIOSSetup  
Double-tap the pen on the display screen or press F2 on your external keyboard.  
The system starts BIOS Setup and the BIOS Setup Main menu is displayed. Note that the system can be  
configured to start without displaying the message above. If this is the case, you must attach an external  
keyboard and hold down the F2 key while you start your system until the BIOS Setup screen is displayed.  
Options and settings for menus in BIOS Setup are described in tables appearing later in this chapter.  
BIOS Setup  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Using BIOS Setup  
3
Once BIOS Setup is started, you can use BIOS Setup to change your system’s BIOS settings. The BIOS  
Setup screen consists of a menu bar, menu items, a command bar, and a window for item-specific help as  
shown in Figure 3-1.  
BIOS Configuration Options  
BIOS Configuration Settings  
Item-Specific Help Window  
PhoenixBIOS Setup Utility  
Menu Bar  
Main  
Advanced  
Security  
Power  
Boot  
Info  
Exit  
Item Specific Help  
System Time:  
System Date:  
[02:34:56]  
[02/01/2001]  
Adjust calendar clock.  
Floppy Disk A:  
Primary Master  
Language:  
[1.44/1.2 MB, 3.5"]  
(Triangle symbol  
indicates that a  
submenu is  
<Tab>, <Shift-Tab>, or  
<Enter> selects field.  
[TOSHIBA MK1516GAP-(PM)]  
[English (US)]  
available)  
F1 Help  
ESC Exit  
Select Item  
Select Menu  
-/Space Change Values  
Enter Select Sub-Menu  
F9 Setup Defaults  
F10 Save and Exit  
Command Bar  
Highlighted text indicates equivalent keyboard command  
Figure 3-1 BIOS Setup Screen  
Instructions for selecting and changing BIOS options and navigating BIOS Setup menus using a pen or  
external keyboard are given below:  
• To select a BIOS Setup menu from the menu bar, tap on the menu name in the menu bar, tap on the  
right or left side of the Select Menu field in the command bar, or use the right or left arrow keys on an  
external keyboard to highlight the menu and display a list of menu options.  
• To select a BIOS option, tap on the setting field for the option, tap on the right or left side of the Select  
Item field in the Command Bar, or use the up and down arrow keys on an external keyboard to  
highlight the option in the list of items for a given menu.  
• To change the setting of a selected BIOS option, tap directly on the setting field, tap on the  
highlighted commands to the right or left of Change Values in the command bar, or use the -, +, / , and  
space keys on an external keyboard to cycle through the list of possible settings. (You can also change  
settings using a pop-up menu as described next.)  
• To access a pop-up menu with a list all possible settings for a given BIOS option, first tap on the  
[option], then tap on the right mouse button hotpad. Tap on the setting once more to view the pop-up  
menu. Double-click on the setting of your choice to select it.  
• To select and enter a submenu, tap twice on the submenu name or select the submenu using the up  
and down arrow keys on an external keyboard and press Enter. (The Main, Advanced, Security, Power,  
BIOS Setup  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
and Boot menus contain submenus.)  
• To view Item-Specific Help for a BIOS option, select the option. Item specific help is displayed in the  
Item Specific Help panel on the right-hand side of the screen.  
• To view General Help for BIOS Setup, tap on Help in the command bar or press F1 on your external  
keyboard. The BIOS Setup help screen is displayed giving general instructions for using BIOS Setup.  
• To exit BIOS Setup, choose the appropriate option from the Exit menu, or tap Save and Exit in the  
command bar, or press F10 on an external keyboard. See “Exiting BIOS Setup” on page 7 for details.  
• To load factory default settings for all BIOS options, select Load Defaults from the command bar.  
Exiting BIOS Setup  
3
Once you are finished making changes in BIOS Setup, you must exit BIOS Setup and allow the system to  
boot to apply your configuration changes. You can exit BIOS Setup by selecting options in the Exit menu.  
The Exit menu includes options that allow you to load default BIOS settings, load previous settings,  
discard your changes, save your changes, and exit BIOS Setup. For details on Exit menu options, see “Exit  
Menu Options” on page 25.  
BIOS Setup  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
BIOS Setup Main Menu Options  
3
Note: All details listed in this chapter reflect BIOS version 1.02.  
BIOS Setup Main menu options are given in Table 3-1. (Options and settings for other BIOS Setup menus  
are described in the tables that follow.) The default setting for each option is listed in bold type when  
applicable.  
Table 3-1. BIOS Setup Main Menu Options  
Option  
System Time  
Settings  
Description  
00:00:00 to 23:59:59  
Real Time Clock (RTC) setting in hours, minutes,  
and seconds. Note that the system time option uses  
a 24 hour format.  
System Date  
01/01/1980 to 12/31/2099  
RTC calendar setting in month/day/year format.  
Floppy Disk A:  
Disabled  
1.44/1.2 MB, 3.5”  
Floppy disk drive type for external floppy drive.  
Selecting [Disabled] disables the floppy disk drive  
port.  
Primary Master Submenu  
Language  
Select this field to access the primary disk drive  
submenu. (See “Primary Master Options” later in this  
section.)  
English  
Select the display language for the BIOS.  
Japanese  
BIOS Setup  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
             
Primary Master Submenu Options  
3
Options and settings for the Primary Master Submenu are given in Table 3-2.  
Table 3-2. BIOS Setup Primary Master Configuration Options  
Option  
Settings  
Description  
Type  
Auto  
IDE hard disk drive configuration method.  
None  
Hard Disk  
Select [Auto] to load configuration parameters from  
the hard disk drive automatically. Selecting [None]  
disables the hard drive. Selecting [Hard Disk] allows  
you to manually enter parameter values for the  
remaining options listed in this table.  
Cylinders*  
Heads*  
0 to 65535  
1 to 16  
Number of cylinders.  
Number of read/write heads.  
Number of sectors per track.  
Display only.  
Sectors*  
0 to 63  
Maximum Capacity  
xxxxMB  
Multi-Sector Transfers*  
Disabled  
2 Sectors  
4 Sectors  
8 Sectors  
16 Sectors  
32 Sectors  
64 Sectors  
128 Sectors  
Number of sectors used in multisector transfers.  
You can cycle through the settings for this option to  
select values up to the maximum 128 sectors  
allowable for the hard disk drive. (Selecting the  
maximum, or values larger than the default may  
degrade performance.)  
LBA Mode Control*  
PIO Transfer Mode*  
Disabled  
Enabled  
Logical Block Address (LBA) mode control. Selecting  
[Enabled] causes logical block addressing to be  
used. Selecting [Disabled] causes cylinder, head,  
and sector addressing to be used.  
Standard  
Determines the method for data transfers to and from  
the hard disk drive.  
(Choosing [Auto] for the HDD Configuration option  
selects the optimum setting for this option.)  
Fast PIO 1  
Fast PIO 2  
Fast PIO 3  
Fast PIO 4  
DMA Transfer Mode*  
Disabled  
Determines the mode used for DMA transfers to/from  
the drive. (Choosing [Auto] for the HDD  
Configuration option selects the optimum setting for  
this option.)  
Multiword DMA 1  
Multiword DMA 2  
Ultra DMA 0  
Ultra DMA 1  
Ultra DMA 2  
* These values can be changed when Hard Disk is selected.  
BIOS Setup  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Advanced Menu Options  
3
Options in the Advanced menu are described in Table 3-3.  
Table 3-3. BIOS Setup Advanced Menu Options  
Settings  
Option  
Plug & Play OS  
Description  
No  
Determines whether BIOS support for Plug and Play  
device configuration is enabled.  
Yes  
Select [Yes] if your operating system supports Plug  
and Play configuration. Select [No] if your operating  
system does not support Plug and Play  
configuration. (Windows 98 and Windows 2000  
support Plug and Play configuration.)  
If this option is set to [Yes], the BIOS only enables  
devices required to boot the system; further  
configuration is performed by the operating system.  
Protected Device Configurations  
No  
Yes  
Select [Yes] to prevent a Plug and Play operating  
system from changing device configuration settings.  
Select [No] to allow a Plug and Play operating  
system to configure system devices.  
Serial/Parallel Port  
Configurations Submenu  
Enter this submenu to configure peripheral  
interfaces. (See “Serial/Parallel Port Configurations  
Submenu Options” on page 11 for details.)  
Keyboard/Mouse  
Features Submenu  
Enter this submenu to configure the system  
keyboard and mouse. (See ““Keyboard/Mouse  
Features Submenu Options” on page 13 for details).  
Video Features Submenu  
Enter this submenu to configure system resources  
for the video controller. (See “Video Features  
Submenu Options” on page 14 for details.)  
Internal Device  
Configurations Submenu  
Enter this menu to configure additional device  
controllers. (See “Internal Device Configurations  
Submenu Options” on page 15 for details.)  
PCI Configurations Submenu  
CPU Features Submenu  
Event Logging Submenu  
Hotpad  
Enter this menu to reserve specific IRQs for use by  
ISA devices. (See “PCI Configuration Submenu  
Options” on page 16 for details.)  
Enter this submenu to change CPU serial number  
features. (See “CPU Features Submenu Options” on  
page 17 for details).  
Enter this submenu to view the Event Log features.  
(See “Event Logging Submenu Options” on page 17  
for details).  
Disabled  
Enabled  
This setting determines whether the following  
hotpads are enabled: Speaker On/Mute, Volume Up/  
Down, Display Select, and Brightness Up/Down.  
BIOS Setup  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Serial/Parallel Port Configuration Submenu Options  
3
Configuration options for the Serial/ Parallel Port Configuration submenu are given in Table 3-4. Note  
that some peripheral interfaces are only available when using a device attached to the system interface  
port such as the mini-dock.  
Table 3-4. Serial/Parallel Port Configurations Submenu Options  
Option  
Serial Port  
Settings  
Description  
Disabled  
Enabled  
Auto  
Determines whether the serial port is active and the  
method used to configure the serial port.  
Select [Auto] to allow the BIOS or operating system  
to configure the port automatically.  
Select [Enabled] to configure the Base I/O Address  
and Interrupt options manually in BIOS setup.  
Select [Disabled] to turn serial port A off.  
I/O Address  
3F8 - 3FF  
2F8 - 2FF  
3E8 - 3EF  
2E8 - 2EF  
Determines the base I/O address used for the serial  
port. The Serial Port option must be set to [Enabled]  
before this setting can be changed.  
Interrupt  
IRQ 3  
IRQ 4  
Determines the interrupt request level used for the  
serial port. The Serial Port option must be set to  
[Enabled] before this setting can be changed.  
Infrared Port  
Disabled  
Enabled  
Auto  
Determines whether the infrared port is active and  
the method used to configure the infrared port.  
Select [Auto] to allow the BIOS or operating system  
to configure the port automatically.  
Select [Enabled] to configure the I/O Address and  
Interrupt options manually in BIOS setup.  
Select [Disabled] to turn off the infrared port.  
Mode  
IrDA  
FIR  
Determines which physical interface the infrared port  
is assigned to. Select IrDA to use the IrDA port in  
Standard IR (SIR) mode (115 Kbps). Select FIR to  
use the IrDA port in Fast IR mode (4 Mbps).  
I/O Address  
3F8 - 3FF  
2F8 - 2FF  
3E8 - 3EF  
2E8 - 2EF  
Determines the base I/O address used for the  
infrared port. The Infrared Port option must be set to  
[Enabled] before this setting can be changed.  
Interrupt  
IRQ 3  
IRQ 4  
Determines the interrupt request level used for the  
infrared port. The Infrared Port option must be set to  
[Enabled] before this setting can be changed.  
I/O Address  
100 - 107  
108 - 10F  
110 - 117  
118 - 11F  
Determines the base I/O address for the infrared  
port. This option is only selectable when the Infrared  
Port Mode setting is FIR.  
BIOS Setup  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
Table 3-4. Serial/Parallel Port Configurations Submenu Options (Continued)  
Option  
DMA Channel  
Settings  
Description  
DMA 1  
DMA 3  
Determines the DMA channel assigned to the  
infrared port when using Fast IR mode. This option is  
only selectable when the Infrared Port Mode setting  
is FIR.  
Parallel Port  
Disabled  
Enabled  
Auto  
Determines how system resources for the parallel  
port are configured.  
Select [Enabled] to configure resources manually.  
Select [Auto] to allow the BIOS (or Plug and Play  
operating system) to configure system resources for  
the parallel port.  
Select [Disabled] to disable the parallel port.  
Mode  
Output Only  
Bidirectional  
ECP  
Determines the operational mode for the parallel  
port. Select Output Only, Bidirectional, or ECP  
(Extended Capabilities Port) depending on which  
setting is appropriate for your application.  
This option is not displayed when the Parallel Port  
option is set to [Disabled].  
I/O Address  
Interrupt  
378 - 37F  
278 - 27F  
3BC - 3BF  
Determines the base I/O address used for the  
parallel port. This option is not displayed when the  
Parallel Port option is set to [Disabled].  
IRQ 3  
IRQ 4  
IRQ 7  
Determines the interrupt request level used for the  
parallel port. This option is not displayed when the  
Parallel Port option is set to [Disabled].  
DMA Channel  
DMA 1  
DMA 3  
Determines the DMA channel assigned to the  
parallel port when using ECP mode.  
This option is only displayed when the Parallel Port  
option is set to ECP.  
BIOS Setup  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Keyboard/Mouse Features Submenu Options  
3
Configuration options for the Keyboard/ Mouse Features submenu are given in Table 3-5.  
Table 3-5. Keyboard/Mouse Features Submenu Options  
Option  
Settings  
Description  
Numlock  
Hot Plug  
Auto  
On  
Off  
This option determines the state of the NumLock key  
when the system is powered on.  
Disabled  
Enabled  
This option determines whether the system is  
hot-pluggable.  
Select [Enabled] to allow devices to be connected  
while the system is running.  
Select [Disabled] to prevent devices from being  
hot-plugged into the system.  
USB Keyboard/Mouse  
Disabled  
Enabled  
Auto  
When [Auto] is selected, Legacy (PS/2) Emulation is  
enabled if a USB keyboard is connected at boot.  
When [Disabled] is selected, Legacy Emulation is  
disabled.  
When [Enabled] is selected, Legacy Emulation is  
enabled and a USB keyboard is available without a  
USB-aware operating system.  
BIOS Setup  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Video Submenu Options  
3
Options for the Video Features submenu are given in Table 3-6.  
Table 3-6. Video Features Submenu Options  
Option  
Settings  
Description  
Display  
Internal Flat Panel  
External  
Determines the default display device.  
Simultaneous  
Select the appropriate option to choose the LCD  
(internal flat panel), an external video monitor, or  
both as the default display device.  
Note that using the Display Select hotpad will change  
this setting.  
Compensation  
Disabled  
Enabled  
Determines whether the VGA images will expand to  
full screen on an SVGA display, or cause VGA  
images to stretch to SVGA on an XVGA display (not  
full screen). Note that if compensation is enabled,  
the display quality will not be as good as if it is  
disabled.  
Select [Disabled] to use the center portion of the  
screen.  
Select [Enabled] to expand the image.  
BIOS Setup  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Internal Device Configurations Submenu  
3
Options for the Internal Device Configurations submenu are given in Table 3-7.  
Table 3-7. Internal Device Configurations Submenu Options  
Option  
Settings  
Description  
Floppy Disk Controller  
Disabled  
Enabled  
When [Enabled] is selected, the floppy disk drive is  
enabled.  
When [Disabled] is selected, the floppy disk drive is  
disabled.  
IDE Controller  
LAN Controller  
Disabled  
Enabled  
When [Enabled] is selected, the IDE port is enabled.  
When [Disabled] is selected, the IDE port is disabled.  
Enabled  
Disabled  
Auto  
When [Auto] is selected, the LAN device is always  
enabled when AC power is supplied. When running  
on battery power, the LAN device is only enabled  
when the link is active.  
When [Enabled] is selected, the LAN device is  
enabled.  
When [Disabled] is selected, the LAN device is  
disabled.  
Modem Controller  
Disabled  
Enabled  
When [Enabled] is selected, the modem is enabled.  
When [Disabled] is selected, the modem is disabled.  
BIOS Setup  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
PCI Configuration Submenu  
3
The PCI Configuration submenu has only one selection: the IRQ Reservation submenu. The IRQ  
Reservation submenu allows you to reserve specific IRQs that are used by legacy devices. Unless you  
need to reserve specific IRQs to resolve a resource conflict, the recommended setting for each of these  
options is Available.  
Table 3-8. PCI Configuration Submenu Options  
Option  
Settings  
Description  
IRQ 3  
IRQ 4  
IRQ 7  
IRQ 9  
IRQ 10  
IRQ 11  
IRQ 15  
Available  
Reserved  
Select Reserved if the IRQ is needed for use by a  
legacy ISA device.  
Available  
Reserved  
Select Reserved if the IRQ is needed for use by a  
legacy ISA device.  
Available  
Reserved  
Select Reserved if the IRQ is needed for use by a  
legacy ISA device.  
Available  
Reserved  
Select Reserved if the IRQ is needed for use by a  
legacy ISA device.  
Available  
Reserved  
Select Reserved if the IRQ is needed for use by a  
legacy ISA device.  
Available  
Reserved  
Select Reserved if the IRQ is needed for use by a  
legacy ISA device.  
Available  
Reserved  
Select Reserved if the IRQ is needed for use by a  
legacy ISA device.  
BIOS Setup  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
CPU Features Submenu  
3
Options for the CPU Features submenu are given in Table 3-9.  
Table 3-9. CPU Features Submenu Options  
Option  
Settings  
Description  
Processor Serial Number  
Enabled  
Disabled  
This option configures the Processor Serial Number  
feature of Pentium III processor. This option is  
accessible via DMI.  
When [Disabled] is selected, the Processor Serial  
Number feature is disabled.  
When [Enabled] is selected, the Processor Serial  
Number feature is enabled.  
Event Logging Submenu  
3
The Event Logging Submenu allows you to configure DMI (Desktop Management Interface) event  
logging options. To access this submenu, select Event Logging Submenu from the Advanced menu.  
Table 3-10. Event Logging Submenu Options  
Option  
Settings  
Description  
Event Log Capacity  
Event Log Validity  
View Event Log  
Status of the event log is displayed.  
Indicates whether data in the event log is valid.  
Enter  
Press the <Enter> key or select the [Enter] option to  
view the contents of the event log.  
Event Logging  
Disabled  
Determines whether DMI event logging is enabled.  
Enabled  
System Boot Event  
Disabled  
Enabled  
This option is only available when [Enabled] is  
selected for Event Logging.  
When [Enabled] is selected, the event may be  
logged.  
When [Disabled] is selected, the event is ignored.  
Clear All Event Logs  
Mark Events as Read  
No  
Yes  
Choose [Yes] to clear all DMI event logs at the next  
boot. (This setting is reset to No after the event logs  
are cleared.)  
Enter  
Press [Enter] or press the <Enter> key to mark all  
events currently in the event log as read. Marked  
events will not be displayed the next time View Event  
Log is selected.  
BIOS Setup  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
Security Menu Options  
3
Security menu options for the Stylistic 3500 pen tablet are described in Table 3-11. Note that settings for  
some security menu options determine whether other options are available.  
Table 3-11. BIOS Setup Security Menu Options  
Option  
Settings  
Description  
Supervisor Password Is  
Set  
Clear  
Indicates whether a supervisor password has been  
specified. (This field cannot be changed directly. To  
enable or disable the supervisor password, enter a  
new password or clear the old password using the  
Set Supervisor Password option.)  
User Password Is  
Set  
Clear  
Indicates whether a user password has been  
specified. (This field cannot be changed directly. To  
enable or disable the user password, enter a new  
password or clear the old password using the Set  
User Password option.)  
Set Supervisor Password  
(Tap on the setting field for  
this option or press the  
<Enter> key to specify a  
supervisor password.)  
Specifying a supervisor password grants access to  
all password protected Security menu options.  
When a supervisor password is enabled and a user  
password is used to enter BIOS Setup, the user  
cannot access the following Security menu options:  
Set Supervisor Password, Floppy Disk Access, and  
Hard Disk Boot Sector.  
When enabled, a supervisor password (or user  
password if used) is required to run BIOS Setup.  
Set User Password  
(Tap on the setting field for  
this option or press the  
<Enter> key to specify a user  
password.)  
Specifying a user password grants access to the  
following Security menu options only: User  
Password, Password On Boot. Other Security menu  
options are not accessible.  
(When a supervisor password is enabled and a user  
password is used to enter BIOS Setup, the user  
cannot access the following Security options: Set  
Supervisor Password, Floppy Disk Access, Hard  
Disk Boot Sector.)  
When enabled, a user (or supervisor) password is  
required to run BIOS Setup.  
Note that a supervisor password must be enabled  
before a user password can be specified.  
Minimum User Password  
Length  
Set the minimum length for the user password. Once  
this field is set, the user cannot enter any passwords  
less than the minimum length.  
Password On Boot  
Disabled  
First Boot  
Every Boot  
Select [Enabled] to require a user or supervisor  
password to boot the system. Note that a user or  
supervisor password must be specified before this  
option can be enabled.  
BIOS Setup  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
Table 3-11. BIOS Setup Security Menu Options (Continued)  
Settings Description  
Option  
Boot from Removable Media  
All  
This option determines who has permission to boot  
the system using removable media. Select  
[Supervisor Only] to allow the system only to be  
booted from removable media after the system is  
started by entering a supervisor password when the  
Password On Boot option is enabled.  
Supervisor Only  
When [Supervisor Only] is selected, the system  
cannot be booted from removable media if  
Supervisor Password is enabled and the Supervisor  
password was not entered at boot time.  
Floppy Disk Access  
All  
This option determines who has access to an  
external floppy drive. Select [Supervisor Only] to  
allow diskette access only after the system is started  
by entering a supervisor password when the  
Password On Boot option is enabled. If the Password  
On Boot option is disabled, the floppy drive is not  
accessible.  
Supervisor Only  
When [Supervisor Only] is selected, the system  
prevents diskette access if Supervisor Password is  
enabled and the Supervisor password was not  
entered at boot time.  
Hard Disk Security Submenu  
Owner Information Submenu  
Hard Disk Boot Sector  
Enter this submenu to configure the hard disk  
security. (See “Hard Disk Security Submenu  
Options” on page -20 for details.)  
Enter this submenu to view and change system  
owner information. (See “Owner Information  
Submenu Options” on page -20 for details.)  
Normal  
Write Protected  
This option write-protects the boot sector on the hard  
disk, to protect against viruses.  
Select [Write Protect] to grant read only access to  
the hard disk drive’s boot sector.  
Select [Normal] to allow read and write access to the  
boot sector.  
Caution  
Selecting [Write Protect] is not advisable on systems  
running Windows 98 or Windows 2000, since those  
operating systems must occasionally write to the  
boot sector. Select [Normal] if your system runs  
Windows 98 or Windows 2000.  
BIOS Setup  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Hard Disk Security Submenu  
3
Hard Disk Security submenu options for the Stylistic 3500 pen tablet are described in Table 3-12.  
Table 3-12. Hard Disk Security Submenu Options  
Option  
Primary Master  
Settings  
Description  
Disabled  
Enabled  
When [Enabled] is selected, the hard disk is locked  
with the password. Data in the locked disk cannot be  
read on any system other than the original system on  
which it was locked, or on systems with identical  
password settings.  
If the Supervisor Password has not yet been set, this  
item is grayed, and cannot be selected or changed.  
When [Disabled] is selected, this feature is disabled.  
Owner Information Submenu  
3
Owner Information submenu options for the Stylistic 3500 pen tablet are described in Table 3-13.  
Table 3-13. Owner Information Submenu Options  
Option  
Settings  
Description  
Owner Information Is  
Clear  
Set  
Display only. Depending upon the current setting of  
the owner information, either [Clear] or [Set] is  
displayed.  
Set Owner Information  
Foreground Color  
Background Color  
Enter  
Press the <Enter> key or select [Enter] to set owner  
information.  
If the Supervisor Password has not yet been set, this  
item is grayed, and cannot be selected or changed.  
The owner information is always displayed on the  
bottom line of the screen during POST.  
Black  
Blue  
Green  
Cyan  
Gray  
Light Blue  
Light Green  
Light Cyan  
Light Red  
Light Magenta  
Yellow  
Bright White  
Set Foreground color.  
Red  
Magenta  
Brown  
White  
Black  
Blue  
Green  
Cyan  
Gray  
Set Background color.  
Light Blue  
Light Green  
Light Cyan  
Light Red  
Light Magenta  
Yellow  
Red  
Magenta  
Brown  
White  
Bright White  
BIOS Setup  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
Power Menu Options  
3
Options for the Power menu are described in Table 3-14. Default settings for most options in this menu  
differ depending on the setting selected for the Power Savings BIOS option. (Refer to Chapter 7 of this  
manual for more information on power management.)  
Caution  
Power savings options should be set to the most conservative  
values possible for your application; doing so extends battery  
life and lowers internal temperatures of the pen tablet.  
Windows 98 and Windows 2000 users: Windows 98/ 2000 are pre-configured to use ACPI. Systems with  
ACPI enabled will not use power management settings configured in BIOS Setup. To configure power  
management settings in Windows 98 or Windows 2000, open Power Management in Control Panel and  
select the desired settings in the Power Management Properties window.  
WIndows NT users: Power management should be disabled in the BIOS, and the Plug & Play OS selection  
under the Advanced BIOS menu should be set to Yes.  
Table 3-14. BIOS Setup Power Savings Options  
Option  
Settings  
Disabled  
Description  
Power Savings  
Select [Maximum Power Savings] to use a power management  
profile designed to maximize battery life.  
Customized  
Select [Maximum Performance] to configure the system to use a  
power management profile designed for maximum system  
performance.  
Maximum Power  
Savings  
Maximum  
Performance  
Select [Customized] to edit power management BIOS options  
directly and create a custom power management profile.  
Select [Disabled] to use no power management (all devices remain  
fully on).  
Hard Disk Timeout  
Off  
30 Seconds  
1 Minute  
2 Minutes  
4 Minutes  
6 Minutes  
8 Minutes  
10 Minutes  
15 Minutes  
20 Minutes  
Determines the amount of time elapsed with no hard disk drive  
activity before the hard disk drive is spun down. Select [Off] to keep  
the hard disk fully powered (always spinning) while the system is  
running. Note that the hard disk drive is more vulnerable to shock  
and vibration damage when it is spinning.  
Display Timeout  
Off  
Use this option to determine the amount of time the user input  
devices are inactive before the screen is turned off automatically.  
2 Minutes  
4 Minutes  
6 Minutes  
8 Minutes  
10 Minutes  
15 Minutes  
20 Minutes  
This setting affects any external video monitor as well as the pen  
tablet display screen.  
Select [Off] to keep the video system fully powered while the  
system is running.  
BIOS Setup  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
             
Table 3-14. BIOS Setup Power Savings Options (Continued)  
Option  
Settings  
Description  
Standby Timeout  
Off  
1 Minute  
Standby Mode turns off various devices in the system, including  
the screen and the CPU until you start using the computer again.  
Select the period of time the system should be inactive before it  
automatically enters standby mode. When in standby mode, some  
system components, including the display, are turned off to  
conserve battery power. Select Off to disable the Standby Mode  
Timeout feature.  
2 Minutes  
4 Minutes  
6 Minutes  
8 Minutes  
12 Minutes  
16 Minutes  
Auto Suspend Timeout  
Off  
Determines the amount of time elapsed with no system activity  
before system operation is suspended automatically.  
5 Minutes  
10 Minutes  
15 Minutes  
20 Minutes  
30 Minutes  
40 Minutes  
60 Minutes  
Suspend Mode  
Suspend  
Save To Disk  
Determines the suspend mode used when you press the Suspend/  
Resume button or when the Suspend Mode Timeout expires.  
Selecting [Suspend] also allows you to configure the Save-To-Disk  
Timeout option.  
Note: You must choose [Suspend] to use the Resume On Modem  
Ring and Resume On Time options. If [Save To Disk] is selected,  
and either Resume On Modem Ring or Resume On Time are  
enabled, the system will suspend to RAM and won’t save to disk.  
Auto Save-To-Disk  
Off  
After 1 Hour  
Determines whether the system automatically performs a  
save-to-disk operation after 1 hour in Suspend mode. To use this  
feature, the Suspend Mode option must be set to [Suspend].  
Resume On Modem Ring  
Off  
On  
Select [On] to configure the system to resume operation when an  
incoming call is detected by your modem.  
This feature will detect a modem ring on the built-in modem, a  
modem installed in a PC Card slot, or an external modem  
connected to a serial port; however, implementation of the ring  
indicator function differs between modem vendors, so this feature  
may not be supported by some third-party modems.  
To use this feature, the Suspend Mode option must be set to  
[Suspend]. If [Save To Disk] is selected, and Resume On Modem  
Ring is On, the system will suspend to RAM and won’t save to disk.  
Resume On Time  
Resume Time  
Off  
On  
Select [On] to configure your system to resume operation at the  
time of day specified in the Resume Time field.  
To use this feature, the Suspend Mode option must be set to  
[Suspend]. If [Save To Disk] is selected, and Resume On Time is  
On, the system will suspend to RAM and won’t save to disk.  
00:00:00  
Determines time of day system will resume when the Resume On  
Time option is On. Enter the time of day in HH:MM:SS format.  
Note: system uses a 24-hour clock.  
Advanced Features  
Submenu  
Select this submenu to further refine power management BIOS  
options. See Table 3-15 for more information.  
BIOS Setup  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
Advanced Features Options Submenu  
3
Options for the Advanced Features Options submenu are described in Table 3-15.  
Table 3-15. BIOS Advanced Features Options Submenu  
Option  
Settings  
Description  
Suspend/Resume Switch  
Disabled  
Enabled  
Determines whether the Suspend/Resume switch is  
enabled or disabled. Note that when this option is in  
Disabled mode, the switch will still resume from an  
auto-suspended state.  
Resume On LAN  
Off  
On  
Selecting [On] allows the system to wake up when  
the internal LAN device receives a Magic Packet  
while in Suspend Mode.  
Serial Mouse Activity  
Disabled  
Enabled  
Determines whether the video system resumes  
when external serial activity is detected.  
Select Enabled to resume video system operation  
when a connected serial device (such as a serial  
mouse) is active.  
Thermal Control  
Maximum Power Savings  
Maximum Performance  
This selection determines the method of thermal  
control used by the system.  
Select [Maximum Power Savings] to use CPU  
slowdown as the primary cooling method.  
Select [Maximum Performance] to use the fan as the  
primary cooling method.  
Note that - if the temperature is too high - both  
systems may be used to cool it down.  
BIOS Setup  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Boot Menu Options  
3
Boot menu options are described in Table 3-16.  
Table 3-16. BIOS Setup Boot Menu Options  
Settings  
Option  
Description  
QuickBoot  
Disabled  
Enabled  
Auto  
Determines whether the full set of tests are run  
during the Power-On Self Test (POST).  
When [Enabled] is selected, a less extensive  
memory test is performed and the size of installed  
memory is not displayed during the memory test.  
When [Auto] is selected, diagnostic tests will either  
be skipped or performed according to the order of  
the ACPI OS.  
When [Disabled] is selected, the full set of tests is  
run.  
Boot Time Diagnostic Screen  
Disabled  
Enabled  
Determines whether status messages are displayed  
as the Power On Self Test (POST) is performed.  
Select [Enabled] to display messages.  
If [Disabled] is selected, messages are not displayed  
and the logo screen is displayed. (If POST errors  
occur, POST messages are displayed regardless of  
this setting.)  
Preboot Execution  
Environment  
Disabled  
Enabled  
Determines whether the boot up from a network  
server.  
Select [Enabled] to allow the system to boot from a  
network server (Preboot Execution Environment).  
If [Disabled] is selected, this feature is disabled.  
Boot Device Priority Submenu  
Select this submenu to configure the order in which  
drives are searched for a bootable image.  
Boot Device Priority Submenu  
3
Table 3-17. describes settings in the Boot Device Priority submenu.  
Table 3-17. BIOS Setup Boot Sequence Submenu  
Setting  
Description  
1. [Floppy Disk Drive]  
2. [Hard Disk Drive]  
Determines the order that the systems searches  
drives for a bootable image.  
1. [Hard Disk Drive]  
2. [Floppy Disk Drive]  
Tap on item 2 to change the boot sequence.  
BIOS Setup  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                 
Info Menu  
3
The Info menu displays information about the pen tablet hardware and BIOS software installed on the  
system as described in Table 3-18.  
Table 3-18. BIOS Setup Info Menu  
Description  
Field  
BIOS Version  
Version number of the BIOS software installed on  
system.  
BIOS Date  
BIOS Area  
CPU Type  
CPU Speed  
L1 Cache  
Release date of the BIOS software.  
Memory area used by the BIOS.  
Pen tablet CPU.  
Processor speed.  
Size of level 1 cache.  
L2 Cache  
Size of level 2 cache.  
Total Memory  
Total memory installed in pen tablet (including built-in  
memory).  
Exit Menu Options  
3
Exit menu options are described in Table 3-19.  
Table 3-19. BIOS Setup Exit Menu Options  
Option  
Description  
Exit Saving Changes  
Exit after writing all changed BIOS Setup settings to  
CMOS memory.  
Exit Discarding Changes  
Exit without saving changes to BIOS Setup settings  
to CMOS memory.  
Load Setup Defaults  
Discard Changes  
Load default settings for all BIOS Setup options.  
Read previous settings from CMOS memory and  
load in all BIOS Setup options.  
Save Changes  
Save BIOS changes to CMOS.  
BIOS Setup  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                       
Using CMOSRDWR  
3
The CMOSRDWR command line allows you to read the system BIOS CMOS contents into a specified  
file, then write the contents into another identical system that uses the same BIOS version. Any number of  
BIOS configurations can be stored using this command, either on the system hard disk or on removable  
media. Using the CMOSRDWR command allows you to create identical BIOS configurations on multiple  
systems.  
Note: • The CMOSRDWR utility should only be used from a real-mode environment (i.e., either from  
Windows command prompt or safe mode command prompt.  
• The utility will only function on Stylistic 3500 platforms that have the same BIOS versions on the  
source and target systems. This is due to the fact that CMOS locations may change from one BIOS  
version to another.  
• If you restore the CMOS contents onto a system in which the user and supervisor passwords have been  
set, the passwords WILL NOT be overwritten.  
• CMOSRDWR automatically updates the CMOS checksum to prevent the checksum error that  
typically occurs when CMOS contents are modified.  
• If the filename specified in the command line already exists in the same location, the file will be  
overwritten without any warning.  
• The Hard Disk Security and Floppy Drive Access settings are dependent upon the supervisor settings.  
If the supervisor password is set, these settings will be reflected correctly, otherwise these settings are  
not selectable.  
Saving a BIOS Configuration Using CMOSRDWR  
3
To run CMOSRDWR, attach a keyboard to your system and perform the following procedure. (An  
external keyboard must be used to type the commands since pen support is not available at the MS-DOS  
level.)  
1. Turn the system on and enter the BIOS setup by double-tapping the screen when prompted.  
2. Adjust the BIOS configuration to the desired settings.  
3. Save and Exit the BIOS setup.  
4. Boot to the MS-DOS prompt.  
5. Go to the DOS command line and type: cmosrdwr read <filename>, with the filename being the  
destination at which you want to store the BIOS configuration that you just created. When you press  
the Enter key, the BIOS configuration is stored in the file destination you selected.  
Restoring a BIOS Configuration  
3
To apply the BIOS setting created with CMOSRDWR, attach a keyboard to your system and perform the  
following procedure. (An external keyboard must be used to type the commands since pen support is not  
available at the MS-DOS level.)  
1. Boot to the MS-DOS prompt.  
2. At the DOS command line, type cmosrdwr write (filename), with the filename being the path to the  
location of the CMOSRDWR BIOS configuration you want to apply to the system.  
3. When you press the Enter key, the BIOS configuration associated with the designated CMOSRDWR  
file is applied to the system BIOS.  
Note: The newly-applied BIOS configuration will not take effect until after the system is rebooted.  
Using CMOSRDWR  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
PHDISK Hard Disk Preparation Utility  
3
The PHDISK hard disk preparation utility can be used to prepare either a dedicated partition or create a  
hidden MS-DOS file for storing system data during a “save-to-disk” operation.  
Note: The Save-to-Disk operation will not work unless the Resume On Modem Ring is disabled in  
both the BIOS and in Windows. In order to disable Resume On Modem Ring, contact Fujitsu PC to  
obtain a patch program which will allow you to disable the function through Windows.  
Caution  
Creating a save-to-disk partition will reformat the hard disk  
drive, erasing all data on the disk. Back up your hard disk  
before using PHDISK to create a save-to-disk partition.  
Command Line Options  
3
Table 3-20 lists PHDISK command line options and additional parameters. Note that PHDISK options can  
be invoked using only the first letter of each option and parameter. For example either,  
PHDISK/REFORMAT  
or  
PHDISK/R  
can be used to invoke the reformat option.  
Table 3-20. PHDISK Command Line Options  
Option  
Parameters  
Description  
None  
/CREATE  
Displays the PHDISK Opening Screen.  
/PARTITION  
Creates a save-to-disk partition. (Entire hard disk is reformatted.)  
Caution  
Creating a save-to-disk partition will reformat the hard disk drive,  
erasing all data on the disk. You must back up your hard disk before  
using PHDISK to create a save-to-disk partition. To avoid reformatting  
your hard disk, use the /FILE parameter instead of the /PARTITION  
parameter.  
/FILE  
If no save-to-disk partition exists, PHDISK creates a save-to-disk file  
large enough for the current system configuration.  
If a save-to-disk partition exists, PHDISK creates a save-to-disk file  
large enough to supplement the existing save-to-disk partition space.  
(The file created provides additional disk space required for save to  
disk operation.)  
/DELETE  
/PARTITION  
/FILE  
Deletes all data in the save-to-disk partition and renders disk space  
occupied by the save-to-disk partition unusable. (You must reformat  
the entire hard disk to use the hard disk space occupied by the  
deleted partition.)  
Delete save-to-disk file.  
PHDISK Hard Disk Preparation Utility  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
Table 3-20. PHDISK Command Line Options (Continued)  
Option  
/INFO  
Parameters  
Description  
/PARTITION  
/FILE  
Displays data about the save-to-disk partition.  
Displays data about the save-to-disk file.  
/REFORMAT  
/PARTITION  
Reformat the save-to-disk partition. This option is typically used if a  
hard disk error is detected in the save-to-disk partition.  
The example below shows the type of information that is displayed when PHDISK is called without a  
command line option. This example displays both the save to disk FILE INFORMATION and  
save-to-disk PARTITION INFORMATION headers. These headers are displayed only when both a  
save-to-disk partition and a save to disk file exist. (The USAGE and OPTIONS headers are displayed in  
several screens displayed by PHDISK).  
Note: When a save-to-disk partition and file both exist, save-to-disk data is stored in the partition first and any  
excess data is stored in the save-to-disk file. It is recommended that you configure your system to use  
either a save-to-disk partition exclusively or a save-to-disk file exclusively. This ensures that your  
save-to-disk data is stored in contiguous disk space.  
PHDISK 3.2.20 -- Phoenix NoteBIOS 4.0 (TM) Save to Disk Preparation Utility  
Copyright (c) Phoenix Technologies Ltd. 1995-99. All rights Reserved.  
Copyright (c) FUJITSU LIMITED. 1998-99  
Save to Disk file information:  
Your Save to Disk file is named C:\SAVE2DSK.BIN and has a size  
of xxxx KBytes. It has System, Hidden, and Read Only attributes.  
Save to Disk partition information:  
Partition starts at sector xxxxx (head xx, cylinder xx, sector xx)  
Partition size: xxxx KBytes total  
Current System Status:  
You currently need a Save to Disk area of xxxx KBytes. PhDisk will  
also require additional overhead and will automatically calculate the  
actual required space.  
You have both a file and a partition. Save to Disk will default  
to file. Either delete the file, or the partition.  
Usage:PHDISK [options]  
/CREATE  
/DELETE  
/INFO  
(/FILE or /PARTITION)  
(/FILE or /PARTITION)  
-- Create STD file or partition  
-- Delete existing STD file or partition.  
-- Information on STD disk area(s)  
-- Reformat existing STD partition  
/REFORMAT /PARTITION  
This utility configures a hard disk to utilize the Phoenix NoteBIOS 4.0  
Save to Disk feature. Please refer to your user manual for information  
regarding Save to Disk.  
CREATE Option  
3
The CREATE option measures the amount of on-board memory, and partitions a segment of the hard  
disk drive large enough to store all the data that might be there. The CREATE option formats the  
save-to-disk partition or file, marking bad spots on the hard disk drive as they are found.  
PHDISK Hard Disk Preparation Utility  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Automatic Memory Size Calculation  
3
PHDISK automatically measures all system and video memory and calculates the exact amount of hard  
disk space required to store the maximum amount of data the memory might contain. The result of this  
measurement, [SIZE], is displayed on the PHDISK screen.  
The total amount of system and video memory is calculated by the following formula:  
Calculated memory = Physical System Memory + Video Memory + 0.3 KBytes (Save to Disk overhead)  
Hard disk space is allocated by cluster, therefore, the save-to-disk partition may exceed [SIZE] by nearly  
one cluster. This space is used, as needed, for the bad-sector replacement pool.  
Specify Memory Size  
3
The amount of disk space required to store all system and video memory is calculated automatically  
whenever the CREATE option is used. If you specify a specific amount of memory, [SIZE], equal to or  
larger than the calculated space required, the amount of memory specified by the [SIZE] parameter is  
allocated. [SIZE] is measured in kilobytes (the measurement notation K, or KB, or KBytes, is not entered  
in the command line).  
• If [SIZE] is larger than or equal to the calculated space required:  
Save to Disk disk space allocated = [SIZE].  
• If [SIZE] is smaller than the calculated space required:  
[SIZE] is ignored, no Save to Disk disk space is allocated, and an error message is displayed.  
/PARTITION or /P  
3
PARTITION creates a hard disk partition where only save-to-disk data is stored.  
Caution  
Creating a save-to-disk partition will reformat the hard disk  
drive, erasing all data on the disk. You must back up your hard  
disk before using PHDISK to create a save-to-disk partition.  
To avoid reformatting your hard disk, use the /FILE parameter  
instead of the /PARTITION parameter.  
Note: The hard disk drive boot sector BIOS configuration option must be set to normal to create a save-to-disk  
partition.  
/FILE or /F  
3
The / FILE parameter creates a file in the hard disk’s MS-DOS partition that is used to store only  
save-to-disk data. When a save-to-disk partition already exists, a file large enough to supplement the  
save-to-disk partition is created by default.  
When the system and video memory outgrows the [SIZE] of the save-to-disk partition, the / FILE option  
can be used to re-allocate disk space. Using / FILE eliminates the user's need to create a new save-to-disk  
partition, and also eliminates the time consuming task of backing up the entire hard disk drive before  
running PHDISK / CREATE / PARTITION.  
If you want to use a save-to-disk file exclusively to store save-to-disk data, you must first delete any  
existing save-to-disk partition before creating a save-to-disk file.  
PHDISK Hard Disk Preparation Utility  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
             
/CREATE Option Syntax  
3
The syntax of the PHDISK / CREATE option is:  
PHDISK /CREATE [SIZE][/FILE][/PARTITION]  
Table 3-21 lists valid examples of the PHDISK / CREATE option.  
Table 3-21. PHDISK /CREATE Option  
Command  
PHDISK /CREATE /FILE  
Description  
If no save-to-disk partition exists, PHDISK creates  
a save-to-disk file large enough for the current  
system configuration.  
(or PHDISK /C /F)  
If a save-to-disk partition exists, PHDISK creates  
a save-to-disk file large enough to supplement the  
existing save-to-disk partition space. (The file  
created provides additional disk space required for  
save-to-disk operation.)  
PHDISK /CREATE /PARTITION  
(or PHDISK /C /P)  
Creates a save-to-disk partition using the amount  
of memory required as calculated by PHDISK.  
Caution  
Creating a save-to-disk partition will reformat the  
hard disk drive, erasing all data on the disk. You  
must back up your hard disk before using PHDISK  
to create a save-to-disk partition. To avoid  
reformatting your hard disk, use the /FILE  
parameter instead of the /PARTITION parameter.  
PHDISK /CREATE 10240 /FILE  
(or PHDISK /C 10240 /F)  
Creates a 10 MB save-to-disk file. The [SIZE]  
variable is 10240.  
REFORMAT Option  
3
The / REFORMAT option resets the pointers in a save-to-disk partition. Use this option after a  
save-to-disk operation is terminated by a read or write error.  
Note: Only save-to-disk partitions can be reformatted; save-to-disk files cannot. If a hard disk error occurs while  
writing to a save-to-disk file, use PHDISK /DELETE /FILE to delete the save-to-disk file. Then, use  
PHDISK /CREATE /FILE to create a new save-to-disk file.  
/REFORMAT Option Syntax  
3
Table 3-22 lists an example of the PHDISK / REFORMAT option.  
Table 3-22. PHDISK /REFORMAT Option  
Command  
Description  
PHDISK /REFORMAT /PARTITION  
(or PHDISK /R /P)  
Reformats the save-to-disk partition.  
PHDISK Hard Disk Preparation Utility  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
             
DELETE Option  
3
When DELETE is specified, the pointers and data in the specified save-to-disk partition or file are deleted.  
Use DELETE when bad data is displayed after a Resume From Disk operation.  
/DELETE Option Syntax  
3
Table 3-23 lists valid examples of the PHDISK / DELETE option.  
Table 3-23. PHDISK /DELETE Option  
Command  
Description  
PHDISK /DELETE /FILE  
(or PHDISK /D /F)  
Delete save-to-disk file.  
PHDISK /DELETE /PARTITION  
(or PHDISK /D /P)  
Deletes all data in the save-to-disk partition and  
renders disk space occupied by the save-to-disk  
partition unusable. (You must reformat the entire hard  
disk to use the hard disk space occupied by the  
deleted partition.)  
INFO Option  
3
The / INFO option displays data about the save-to-disk partition or file.  
/INFO Option Syntax  
3
Table 3-24 lists valid examples of the PHDISK / INFO option.  
Table 3-24. PHDISK /INFO Option  
Command  
PHDISK /INFO /FILE  
Description  
Displays the size (in kilobytes) of the  
save-to-disk file size.  
(or PHDISK /I /F)  
PHDISK /INFO /PARTITION  
(or PHDISK /I /P)  
Displays the PHDISK /INFO screen.  
An example of the / INFO screen when a save-to-disk partition exists is shown below:  
PHDISK 3.2.20 -- Phoenix NoteBIOS 4.0 (TM) Save to Disk Preparation Utility  
Copyright (c) Phoenix Technologies Ltd. 1995-99. All rights Reserved.  
Copyright (c) FUJITSU LIMITED. 1998-99  
Save to Disk partition information:  
Partition starts at sector xxxxx (head xx, cylinder xx, sector xx)  
Partition size: xxxx KBytes total  
Current System Status:  
You currently need a Save to Disk area of xxxx KBytes. PhDisk will  
also require additional overhead and will automatically calculate the  
actual required space.  
PHDISK Hard Disk Preparation Utility  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
               
Messages  
3
PHDISK returns various informational messages, not all of which are listed here. The following listing  
emphasizes the error messages, including a possible course of action.  
PHDISK Sign-on Message  
3
This message is displayed at system startup.  
PHDISK X.X - Phoenix NoteBIOS 4.0 (tm) Save to Disk Preparation Utility  
Copyright (c) Phoenix Technologies Ltd. 1995-99. All rights reserved.  
Copyright(c)FUJITSULIMITED.1998-99  
Help Screen  
3
The HELP screen is displayed when PHDISK is called without options. The following text is displayed  
when a save-to-disk partition already exists.  
Usage:PHDISK [options]  
/CREATE  
/DELETE  
/INFO  
(/FILE or /PARTITION) -- Create STD file or partition  
(/FILE or /PARTITION) -- Delete existing STD partition.  
-- Information on STD disk area(s)  
/REFORMAT /PARTITION  
-- Reformat existing STD partition  
This utility configures a hard disk to utilize the Phoenix NoteBIOS 4.0  
Save to Disk feature. Please refer to your user manual for information  
regarding Save to Disk.  
Unrecognized Option  
3
3
3
The following text is displayed when an invalid option is entered at the command line.  
Error: (User option) is an unrecognized command line option.  
For a command line summary, invoke PHDISK without any parameters.  
Run the PHDISK command again in this case.  
Fatal Error  
The following text is displayed when a hard disk error is detected during any save-to-disk operation.  
Error: A fatal hard disk error has occurred.  
Check your hardware configuration and re-execute PHDISK.  
Run a hard disk utility to determine the source of the error, then re-execute the PHDISK command.  
Not Enough Disk Space  
The following text is displayed when the amount of unused disk space available is less than the amount  
required to create the save-to-disk partition.  
Error: Not enough free disk space exists to create the suspend to disk  
partition. Refer to the user manual for possible suggestions on increasing  
the amount of free disk space for the suspend to disk partition.  
Delete unused files, backup the DOS partition, reformat the disk, then run  
PHDISK / CREATE / PARTITION to create a larger partition.  
PHDISK Hard Disk Preparation Utility  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                 
Save to Disk Partition Exists  
3
The following text is displayed when a PHDISK / CREATE / PARTITION operation is attempted while a  
save-to-disk partition exists.  
Error:Phoenix NoteBIOS Save to Disk partition already exists. To resize the  
partition, delete the existing partition with PHDISK/DELETE and create the  
partition with PHDISK/CREATE.  
Reallocate the save-to-disk partition if needed, or use the / CREATE / FILE option instead. (Note that a  
partition will require contiguous disk space.)  
Too Many Bad Sectors  
3
The following text is displayed when the save-to-disk partition is too small because of an increasing  
number of bad sectors.  
Error: Too many errors exist in the Phoenix NoteBIOS (tm) Save to Disk  
partition. Check your hardware configuration and rerun PHDISK.  
Execute PHDISK / CREATE / FILE to create a save-to-disk file.  
First Two Sectors Bad  
3
The following text is displayed when the save-to-disk partition cannot be used.  
Error: The first two sectors in the Save to Disk partition are both  
unusable. This disk is unsuitable for the Phoenix NoteBIOS Save to Disk  
feature.  
Attempt to reformat the partition using PHDISK / REFORMAT / PARTITION. (You may need to first  
delete the partition using PHDISK / DELETE / PARTITION depending on the disk error.)  
PHDISK /CREATE Failed to Execute  
3
The following text is displayed when no save-to-disk partition exists, or the partition table on head 0,  
cylinder 0, sector 1 is corrupted.  
Error: The Phoenix NoteBIOS (tm) Save to Disk partition doesn’t exist or the  
hard disk partition table on head 0, cylinder 0, sector 1 is corrupted.  
Invoke PHDISK/CREATE to create the Save to Disk partition.  
Execute PHDISK / CREATE / PARTITION.  
Good Sector Map Corrupted  
3
The following text is displayed when a save-to-disk partition exists but the GSM is corrupted.  
Error: The "Good sector map" (GSM) in the Phoenix NoteBIOS Save to Disk  
partition is bad. Invoke PHDISK /REFORMAT to rebuild this table.  
Use PHDISK / REFORMAT / PARTITION to reset the GSM flags.  
PHDISK Hard Disk Preparation Utility  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
Not Enough System Memory  
3
3
The following text is displayed when not enough system memory is available to execute PHDISK.  
Error: Couldn’t allocate additional memory required to execute PHDISK.  
Add more system memory, then try the PHDISK command again.  
File Already Exists  
The following text is displayed when the PHDISK / CREATE / FILE command is entered when a  
save-to-disk file already exists.  
PHDISK X.X -- Phoenix NoteBIOS 4.0 (tm) Save to Disk Preparation Utility  
Copyright (c) Phoenix Technologies Ltd. 1995-99. All rights reserved.  
Copyright (c) FUJITSU LIMITED. 1998-99  
Save to Disk file information:  
Your Save to Disk file is named C:\SAVE2DSK.BIN and has a size  
of xxxx KBytes. It has System, Hidden, and Read Only attributes.  
The system will now be reset to allow the BIOS to  
recognize the changes. If the system fails to reboot,  
please reset the system manually.  
Press any key to reset the system...  
Delete the current file, using PHDISK / DELETE / FILE, before creating another save-to-disk file.  
PHDISK Hard Disk Preparation Utility  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Chapter 4  
Installing Hardware Options  
This chapter provides procedures for installing PC Cards and DIMM cards. (For details on replacing the  
pen tablet’s internal IDE hard disk drive, refer to “Removing the Hard Disk Drive” on page 75.)  
Installing a PC Card  
4
You can install a PC Card while the system is running, when the system is off, or when system operation  
is suspended.  
To install a PC Card,  
1. With the arrow on the PC Card facing up, insert the card through the shutters in the PC Card slot, as  
shown in Figure 4-1.  
2. Push the PC Card into the slot until it is seated.  
3. If necessary, install any driver or application software necessary to use your PC Card. Note that Card  
and Socket Services are configured automatically by the operating system.  
The PC Card is now installed and you can use the PC Card with your system.  
PC Card slot  
Eject button  
Figure 4-1 Installing a PC Card  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
Removing a PC Card  
4
4
To remove a PC Card,  
1. Stop the PC Card using the appropriate features of your operating system.  
2. Press the Eject button for the PC Card slot.  
3. Pull the PC Card all the way out of the slot.  
Installing a DIMM Card  
Only one DIMM socket is available on the pen tablet. You will need to remove any DIMM card currently  
installed in the system before you can install a new DIMM card. See “Removing a DIMM Card” on page  
37 for details.  
To install a DIMM card in the pen tablet,  
1. Ensure that the pen tablet is off. To do so, carry out the Shut Down command in the Start menu. (Do  
not attempt to remove or install a DIMM card when the system is in Suspend mode or running.)  
2. Remove the two screws from the cover plate on the back of the pen tablet and remove the cover plate  
as shown in Figure 4-2.  
Figure 4-2 Installing a DIMM Card  
3. Insert the DIMM card in the socket at an angle and push it down until it locks into place. Note that the  
DIMM card is keyed to prevent it from being inserted backwards.  
4. Reinstall the cover and screws that you removed in step 2.  
5. Confirm that the DIMM card is recognized by the system. To do so, run BIOS Setup. The size of the  
DIMM card should be displayed in the Info menu in BIOS Setup.  
The DIMM card is installed in the pen tablet and you can now use the system.  
Removing a PC Card  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Removing a DIMM Card  
4
To remove a DIMM card,  
1. Ensure that the pen tablet is off. To do so, carry out the Shut Down command in the Start menu. (Do  
not attempt to remove or install a DIMM card when the system is in Suspend mode or running.)  
2. Remove the screws from the cover plate on the back of the pen tablet and remove the cover plate as  
shown in Figure 4-2.  
3. Spread the fingers on the socket that lock the DIMM card in place until the DIMM card is loose.  
Reference Figure 4-3.  
4. Remove the DIMM card from the socket.  
5. Reinstall the cover plate if you are not installing a new DIMM card.  
The DIMM card is now removed from the pen tablet. Refer to “Installing a DIMM Card” on page 36 if  
you are installing a new DIMM card.  
Figure 4-3 Removing a DIMM Card  
Removing a DIMM Card  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Chapter 5  
Hardware Specifications  
Specifications for the Stylistic 3500 pen tablet and mini-dock are given in this chapter.  
General Specifications  
5
General specifications for the pen tablet are given in Table 5-1.  
Table 5-1. Logic System Specifications  
Feature  
Architecture  
Specification  
IBM-AT compatible  
Comments  
Microprocessor  
Chipset  
Intel 500 MHz Celeron processor  
Intel 440MX -100  
100 MHz system bus  
Cache  
Level 1 (L1) cache: 32 KB  
Level 2 (L2) cache: 128 KB  
L1 cache (internal CPU) is always enabled.  
Flash ROM with boot block  
512 KB (flash ROM upgradeable)  
BIOS ROM  
RAM (expansion)  
One 144-pin DIMM slot.  
Supports up to 256MB memory.  
Total allowable RAM is 256MB. Memory  
from third-party vendors is not supported for  
use with the Stylistic 3500 pen tablet.)  
Video Controller  
Video Memory  
I/O Controller  
ATI Mobility-M  
4MB VRAM  
Mobile multimedia VGA controller with  
SVGA enhancements.  
High speed VRAM integrated in video  
controller.  
FDC37N769  
Standard Microsystems Corporation  
Controller for: serial ports, parallel port, IrDA  
port, and floppy disk drive.  
PC Card Controller  
PCI1420  
Texas Instruments  
Controller is on PCI bus. Supports CardBus  
(PCI bridge) and PCIC protocols. Note that  
the controller does not support Zoomed  
Video.  
Audio Controller  
Integrated into the Intel chipset, supported by  
AC’97 - SigmaTel codec.  
LAN Controller  
Modem Chipset  
Intel 82559  
Built around Lucent 1646 DSP chipset  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                             
Display Specifications  
5
Specifications for the Stylistic 3500 pen tablet display are given in Table 5-2.. The Stylistic 3500 pen tablet  
is available with one of three different displays. Note the display type for your system when referring to  
this table. Comments indicate which displays are best suited to particular environments and applications.  
Table 5-2. Display Specifications  
Feature  
Specification  
Comments  
Indoor Color TFT  
LCD  
• 10.4" diagonal TFT Color  
• XGA 1024 x 768 dot composition  
• Transmissive  
Best choice for indoor lighting environments.  
• 256 K colors  
• Brightness: Minimum 13 nits (cd/m2)  
Maximum 130 nits (cd/m2)  
• Backlight: CFL x 1, 8 gradations  
Indoor/Outdoor Color  
TFT LCD  
• 10.4" diagonal TFT Color  
• SVGA 800 x 600 dot composition  
• Transmissive  
Best choice when pen tablet must be used  
both indoors and outdoors. When used  
indoors, the LCD backlight provides  
adequate display brightness. When used  
outdoors, the LCD can be used with  
reflected light only (the backlight may be  
needed in the shade).  
• 256 K colors  
• Brightness: Minimum 15 nits (cd/m2)  
Maximum 150 nits (cd/m2)  
• Backlight: CFL x 1, 8 gradations  
Outdoor Color TFT  
LCD  
• 10.4" diagonal TFT Color  
• SVGA 800 x 600 dot composition  
• Reflective  
Best choice when pen tablet must be used  
primarily outdoors.  
• 256 K colors  
External Video Capabilities  
5
The Stylistic 3500 pen tablet port replicator or mini-dock can drive an external video monitor. You can  
select an external monitor, the pen tablet display screen, or both as the active video display. The pen  
tablet supports VGA, SVGA, and XGA video modes with external monitors. Screen resolutions supported  
for external video monitors are given in Table 5-3.  
Note: After panning, stretching, or rotating the display, be sure to return the display to its normal resolution  
before attempting to recalibrate the pen.  
Table 5-3. Supported Video Modes for External Monitors  
Resolution  
Colors  
Up to 16 M  
640x480 (VGA)  
800x600* (SVGA)  
1024x768** (XGA)  
Up to 16 M  
Up to 16 M  
* SVGA LCD: For an SVGA LCD or external monitor, 800x600 resolution will not compensate, but display will be  
small.  
** XGA LCD: For XGA LCD or external monitor, 1024x768 resolution will not compensate, but display will pan.  
Display Specifications  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
             
Digitizer Specifications  
5
The Stylistic 3500 pen tablet digitizer consists of the pen, a sensor grid, and supporting controller  
circuitry. The sensor grid is built into the pen tablet in front of the display screen and detects pen  
pressure.  
Technology Notice  
5
The display for your pen tablet incorporates a breakthrough digitizer technology that dramatically  
improves outdoor viewability. Compared to traditional outdoor displays, the new display excels in  
providing superior visibility in full sunlight, and a clear, bright picture indoors, in low light conditions, or  
at night.  
This new technology involves the use of a liquid between the digitizer layers to minimize light refraction  
and reduce glare. As a result of this technology, users may notice the appearance of tiny air bubbles  
which are caused by changes in atmospheric pressure (such as that experienced in an airplane). These  
tiny bubbles are temporary and do not affect system performance or usability. The digitizer still functions  
normally when the air bubbles are present.  
The air bubbles are formed when the liquid vaporizes due to pressure change. When the pen tablet is  
returned to normal use conditions, the tiny air bubbles are absorbed back into the liquid after a short  
amount of time.  
If these air bubbles are visually distracting, or if they form a larger bubble, gently rub the screen with a  
soft cotton cloth in a circular motion, similar to cleaning the screen of fingerprint oil.  
Table 5-4. Digitizer Specifications  
Feature  
Specification  
Pressure-sensitive  
Comments  
Type  
Resistive digitizer  
Active Area  
213.2 mm x 160.4 mm  
0.1 mm  
Area of display screen that reacts with the pen.  
Resolution  
Maximum Sampling Rate  
Interface  
100 points per second  
Serial interface  
None  
Pen Switches  
Pen buttons can be emulated with use of  
right-mouse button hotpad.  
Digitizer Specifications  
40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
Peripheral Interface Specifications  
5
Specifications for peripheral interfaces on the Stylistic 3500 pen tablet are given in Table 5-5. For  
specifications on peripheral interfaces provided by the port replicator, see “Port Replicator Specifications”  
later in this chapter. Also note that pin assignments and other details for peripheral interfaces on the  
Stylistic 3500 pen tablet are given in Chapter 6 of this manual.  
Table 5-5. Peripheral Interface Specifications  
Feature  
Specification  
Comments  
PC Card Slot  
One Type II PCMCIA CardBus slot.  
Compliant with PC Card Standard Rev. 3.0  
Supports CardBus and PCIC (PC Card I/O  
Cards)  
IDE Interface  
Modem Port  
Supports one IDE hard disk drive (2.5 inch)  
RJ-11 connector for internal modem  
IDE hard disk drive is preinstalled at factory.  
See “Internal LAN/Modem Specifications” on  
page 44 for more information. Note that the  
LAN portion of the device is accessible only  
via the mini-dock.  
Serial Port  
Standard 9-pin connector that allows you to  
connect an external serial device.  
Universal Serial Bus  
Port (USB A)  
One USB Series A receptacle on pen tablet.  
IrDA Port  
Infrared transceiver built into pen tablet.  
Compliant with IrDA Standard Revision 1.1  
Supports: FIR (4 Mbps max),  
SIR (115 Kbps max)  
Range: approximately 1 M, 15 degrees from  
center  
Infrared Keyboard  
Port  
Infrared receiver built into the pen tablet for  
use with an optional infrared keyboard.  
Proprietary Fujitsu receiver.  
Range: approximately 1 M, 15 degrees from  
center  
DC Power Input  
16 VDC ±10%, 3.36 A  
External power can be connected to DC  
input connector on the pen tablet, mini-dock,  
port replicator, or high-usage contacts. See  
“DC Power Inputs” on page 67 for more  
details.  
Connector vendor: Hosiden  
(Hosiden part number HEC3900-01-010)  
This connector is a EIAJ-RC5320A standard  
connector.  
Audio Jacks  
Monaural microphone input mini jack  
Stereo headphone output mini jack  
Standard 3.5 mm mini jacks.  
See “Audio Jacks” on page 59 for details on  
audio inputs and outputs.  
System Interface  
Port  
200-pin connector  
For use with Stylistic 3500 port replicator or  
mini-dock.  
High-Usage  
Contacts  
8-position external contact connector  
provides connections for: DC power input and  
USB.  
See “High Usage Contacts” on page 47 for  
signal assignments of the high-usage  
contacts.  
Floppy Disk Drive  
Port  
26-pin floppy disk drive connector  
For use with Fujitsu floppy disk drive.  
Peripheral Interface Specifications  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                           
Power System Specifications  
5
Specifications for the Stylistic 3500 pen tablet power system are given in Table 5-6. The power system and  
power management characteristics are further described in Chapter 7 of this manual.  
Table 5-6. Power System Specifications  
Feature  
Specification  
Comments  
Power Management  
Specification  
ACPI Specification Revision 1.0  
ACPI: Windows 98 and Windows 2000 are  
supported.  
Supported  
Battery Pack  
Rechargeable 6-cell lithium ion battery pack  
Capacity: 3100 mAh  
Nominal operating voltage: 10.8 V  
Charge time (in suspend or off mode):  
≈ 180 minutes (90% charge)  
≈ 240 minutes (99-100% charge)  
Charge time (system running): Depends upon  
applications in use, power management utility  
setup, and backlight.  
Charge times are for a 0% charged battery  
pack charging in pen tablet (not in an  
external battery charger).  
If the battery pack is 90% or higher when you  
connect DC power, the battery pack will not  
charge, thus preventing overcharging.  
Battery life values are approximate.  
Battery life:  
≈ Approximately 4 hours when running  
(dependent upon application, power  
management, and backlight)  
≈ Minimum 5 days in Suspend-to-RAM mode  
≈ Approximately 30 days in Fully Off mode  
Bridge Battery  
• Nickel metal hydride  
• 6 cells  
Bridge battery supplies power to RAM in  
suspend mode for about 5 minutes while  
battery pack is removed. (Note: bridge  
battery cannot power system in fully on  
mode.)  
• Capacity: 6.0 V, 35 mAH (210 mWh)  
• Suspend life (backup battery only):  
Approximately 5 minutes  
Bridge battery is charged:  
• In all modes when external DC power is  
connected.  
• Charge Time: 100 hours (with AC)  
• In On, Idle, or Standby modes (when  
system is running) when external power  
is not connected.  
Sub Battery  
AC Adapter  
• Lithium battery (built in)  
• 265 mAh  
Provides real time clock power backup.  
Approximate battery life is 5 years. (Not field  
replaceable.)  
• Input: 100-240 VAC, 50/60 Hz  
• Output: 16 VDC ±10%, 3.36 A  
Power System Specifications  
42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                 
Environmental Specifications  
5
Environmental specifications for the Stylistic 3500 pen tablet are given in Table 5-7.  
Table 5-7. Environmental Specifications  
Feature  
Temperature  
Specification  
Operating: 0° to 40°C (32° to 104°F)  
Nonoperating: -20° to 60°C (-4° to 140°F)  
(with appropriate power management)  
Humidity  
Vibration  
Operating: 20% to 80% RH noncondensing  
Nonoperating: 20% to 80% RH noncondensing  
0.67G, random  
Physical Specifications  
5
Physical specifications for the Stylistic 3500 pen tablet are given in Table 5-8.  
Table 5-8. Stylistic 3500 Pen Tablet Specifications  
Feature  
Specification  
Pen Tablet Dimensions  
11 x 8.5 x 1.1 in (280 x 215 x 27.4 mm)  
3.2 lbs. (1.45 Kg)  
Pen Tablet Weight  
(with battery pack)  
Hand Strap Inserts  
M-3 size, 4mm depth  
Agency Approval Specifications  
5
Specifications for government agency approvals are given in Table 5-9.  
Table 5-9. Agency Approval Specifications  
Feature  
Emissions  
Specification  
• FCC Part 15 Class B  
• EN55022 Class B  
• EN55024  
Immunity  
Safety  
• EN61000-3-2  
• EN61000-3-3  
• UL 1950  
• CSA950  
• EN60950  
Modem  
• FCC Part 68  
• IC CS03  
Environmental Specifications  
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                   
Internal LAN/Modem Specifications  
5
The internal LAN/ modem device connects to the system’s PCI bus. Specifications for the internal LAN/  
modem are given in Table 5-10. The internal LAN/ modem is built-in and is not field replaceable. The  
internal modem is a global device.  
Table 5-10. Internal LAN/Modem Specifications  
Feature  
Specification  
LAN Part  
Transmission media  
Transmission system  
Data transfer velocity  
Network form  
Non-shielded twisted-pair cable.  
Base-band method  
100 Mbps/10 Mbps  
Star  
Max. segment length  
100 m  
Max. number of node/  
segments  
Dependent upon hub  
Data link control  
method  
CSMA/CD  
Message protocol  
Variable length frame  
Pre-amp  
Synchronous method  
Error correct method  
32-bit CRC check  
Frame addressing  
method  
Unique address  
Group address  
Simultaneous address  
Data encode/decode  
method  
Manchester method (10 Mbps)  
MLT-3 method (100 Mbps)  
Chipset  
Built around Lucent  
1646 DSP chipset  
56 Kbps*  
Modem Part  
Data rate  
Protocols  
• ITU-T V.90  
• ITU-T V.34  
• ITU-T V.32bis  
• ITU-T V.32  
• ITU-T V.22bis  
Standards  
Hayes AT command set  
• V.42bis data compression  
• MNP Class 5 data compression  
Compression method  
Error correction  
V.42 automatic correction  
MNP Class 4  
Compliance  
countries  
US / Canada / Japan / Belgium / Denmark / Finland / France /  
Germany / The Netherlands / Italy / Norway / Sweden / Switzerland /  
United Kingdom / Austria / Portugal / Ireland / Spain / Greece  
Internal LAN/Modem Specifications  
44  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Table 5-10. Internal LAN/Modem Specifications  
Feature  
Specification  
EIA/TIA 578 (Class 1)  
Fax  
Standard  
Protocol  
G3 facsimile standard: ITU-T T.30  
Capability  
ITU-T V.17  
ITU-T V.29  
ITU-T V.27  
ITU-T V.21 ch2  
*
Current FCC restrictions, line conditions, and other external factors will reduce  
actual data transmission rates.  
Internal LAN/Modem Specifications  
45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Port Replicator/Mini-Dock Specifications  
5
The Stylistic 3500 port replicator and mini-dock are designed to provide optimal support for your pen  
tablet. Specifications for interfaces on the Stylistic 3500 port replicator and mini-dock are given in Table  
5-11. Note that these interfaces duplicate corresponding ports on the pen tablet. For details on peripheral  
interfaces provided by the port replicator and mini-dock, refer to Chapter 6 of this manual.  
Note: The connectors and ports on the port replicator and mini-dock are identical with one exception: the  
mini-dock has a PCMCIA slot, but the port replicator does not.  
Table 5-11. Stylistic 3500 Port Replicator/Mini-Dock Specifications  
Feature  
Specification  
Comments  
DC power input  
+ tip / - sleeve  
16 VDC ±10%, 3.36 A  
Keyboard Port  
Mouse Port  
Video Port  
6-pin PS/2-style  
Supports most PS/2-style keyboards.  
6-pin PS/2-style  
Standard 15-pin video connector  
System supports simultaneous operation of  
external monitor with LCD.  
Serial Port A  
LAN Port  
Male 9-pin D connector  
Standard RJ-45 port  
NS 16C550-compatible, fully functional  
RS-232C serial port.  
See “Internal LAN/Modem Specifications” on  
page 44 for more information. Note that this  
portion of the LAN/Modem device is  
accessible only via the port replicator or  
mini-dock.  
Floppy Disk Drive  
Port  
26-pin connector for use with Fujitsu floppy  
disk drives.  
Line Output Jack  
3.5 mm mini stereo jack  
Using the line output jack does not disable  
any other audio features on the pen tablet or  
port replicator. (The line output jack is not  
disabled when other audio jacks are used.)  
Universal Serial Bus  
Port  
USB Series A receptacle  
Parallel Port  
25-pin D connector, female  
Standard 68-pin PCMCIA connector  
Output only, bidirectional, and ECP  
operational modes are supported.  
PCMCIA  
Available on mini-dock only. Will support one  
Type III or two Type II CardBus cards.  
Port Replicator/Mini-Dock Specifications  
46  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
Chapter 6  
Peripheral Interfaces  
Details on peripheral interfaces on the Stylistic 3500 pen tablet are described in this chapter.  
The Stylistic 3500 pen tablet provides the following peripheral interfaces:  
• DC input connector  
• Serial port  
• IrDA port  
• Infrared keyboard port  
• Universal Serial Bus (USB)  
• RJ-11 jack for internal modem  
• Stereo headphone jack  
• Stereo microphone jack  
• System interface port*  
• High-usage contacts  
• Floppy disk drive port  
• PC Card socket  
• Hard disk drive port  
* Note that the system interface port (also referred to as the port replicator or mini-dock connector in  
some documentation) allows you to connect the Stylistic 3500 port replicator or mini-dock.  
Pin assignments for peripheral interfaces on the Stylistic 3500 pen tablet are given in the following  
sections.  
High Usage Contacts  
6
The high usage contacts on the Stylistic 3500 pen tablet provide signals for the DC power input and USB  
devices. Signal assignments for the metal contacts are shown in Table 6-1.  
Table 6-1. Metal Contacts  
Connector Position Locations  
Position  
Signal  
1
2
3
4
5
6
7
8
DC-IN  
DETECT0  
USBVCC1  
USBP-  
USBP+  
USBG  
1
8
DETECT1  
GND  
High Usage Contacts  
47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
               
Serial Port  
6
The serial port provides a standard 9-pin connector that allows you to use the pen tablet with an external  
serial device. Pin assignments for the serial port connector are shown in Table 6-2.  
Table 6-2. Serial Port Connector Pin Assignments  
Connector Pin Locations  
Pin  
Signal Name  
Host  
I/O  
1
CD  
2
3
4
RD (RxD)  
SD (TxD)  
ER (DTR)  
5
6
SG (GND)  
DR (DSR)  
-----  
7
8
9
RS (RTS)  
CS (CTS)  
CI (RI)  
DC Power Input  
6
The DC power input connector connects to the AC adapter or auto adapter to power the pen tablet. The  
DC power input connector is a two-conductor connector with a center pin and sleeve. Pin assignments for  
this connector are given in Table 6-3.  
Table 6-3. DC Power Input Connector Pin Assignments  
Conductor  
Center Pin  
Sleeve  
Description  
Comments  
16 Volts DC ±10%, 3.36 A  
Ground  
(Hosiden part number  
HEC3900-01-010)  
This connector is a  
EIAJ-RC5320A standard  
connector. See “DC Power Input  
Connector Pin Assignments” on  
page 48 for more details.  
When a DC power source is connected to the DC power input on the pen tablet, circuitry built into the  
pen tablet provides protection against reverse polarity and overvoltage.  
Serial Port  
48  
Download from Www.Somanuals.com. All Manuals Search And Download.  
             
Floppy Disk Drive Port  
6
The floppy disk drive port on the pen tablet is compatible with the Fujitsu floppy disk drive. Pin  
assignments for the floppy disk drive connector are given in Table 6-4.  
Table 6-4. Floppy Disk Drive Connector Pin Assignments  
Signal  
Name  
Connector Pin Locations  
Pin  
Signal Description  
1
GND  
Ground  
Ground  
2
GND  
25 23 21 19 17 15 13 11  
9
7
8
5
6
3
4
1
3
HDSEL#  
RDATA#  
FDATCH#  
WDATA#  
MODE#  
N.C.  
Head select  
Read disk data  
Floppy disk drive attached  
Write data  
26 24 22 20 18 16 14 12 10  
2
4
5
6
7
Mode select  
No connection  
Drive select  
5-Volt power  
5-Volt power  
5-Volt power  
Index  
8
9
DRVSEL#  
5V  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
5V  
5V  
INDEX#  
WP#  
Write protected  
Track 00  
TRK0#  
GND  
Ground  
WGATE#  
GND  
Write gate  
Ground  
N.C.  
No connection  
Step pulse  
STEP#  
DIR  
Direction control  
Motor on  
MOTOR#  
N.C.  
No connection  
Disk change  
Ground  
DSKCHG#  
GND  
N.C.  
No connection  
#Indicates active-low signal.  
Floppy Disk Drive Port  
49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Universal Serial Bus Port  
6
The pen tablet provides a Universal Serial Bus (USB) port that is compliant with the Universal Serial Bus  
Specification Revision 1.0. The USB port is a powered USB hub and can support concurrent operation of up  
to 127 devices. The Stylistic 3500 pen tablet functions as a USB host and supports high-power,  
bus-powered functions as defined in the USB specification. System resources for the USB are assigned by  
the operating system, no software configuration is necessary; however, it may be necessary to install  
drivers and application software to support your USB device.  
The Stylistic 3500 port replicator and mini-dock provide one USB port. The pen tablet can supply a  
maximum of 500 mA at 5 volts (or a 5-unit load as defined by the USB specification) on each USB  
connector (for a total of 1,000 mA using both USB connectors, one on main unit and the other on the port  
replicator, or mini dock, or high usage cradle, or wall mount cradle).  
Ensure that your USB configuration does not exceed this maximum load. Note that the conductor gauge  
and length of your USB cabling will affect the voltage drop and signal propagation between USB devices.  
Refer to the Universal Serial Bus Specification for details on cable requirements or contact your cable  
vendor. Also note that some USB devices are self-powered and do not draw power over the USB cable.  
Contact pin assignments for the USB port are shown in Table 6-5.  
Table 6-5. Universal Serial Bus Port Contact Pin Assignments  
Contact  
Number  
Contact Pin Locations  
Signal Name  
Signal Description  
1
5V  
Cable power (+ 5 volts DC,  
500mA)  
Position 2  
Position 1  
Position 3  
Position 4  
2
3
4
DATA -  
DATA +  
GND  
Data  
Data  
Cable ground  
Universal Serial Bus Port  
50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
System Interface Port  
6
The system interface port on the Stylistic 3500 pen tablet allows you to attach the Stylistic 3500 port  
replicator or mini-dock. The system interface port is a 200-pin connector. Figure 6-1 shows the pin  
locations for the system interface port connector on the pen tablet.  
Note: The connectors used for the system interface port are manufactured by JAE. Part numbers are:  
female: KX20-200RG-F2LT, male: KX20-200BG-F2LT  
Figure 6-1 System Interface Port Connector (On Pen Tablet)  
LCD Side  
50  
49 48 47  
4
3
2
1
100 99 98 97  
54 53 52 51  
150 149 148 147  
200 199 198 197  
104 103 102 101  
154 153 152 151  
Back Side  
The pin assignments for the system interface port connector on the pen tablet are given in Table 6-6.  
Signals designated with the “pound” (#) symbol are active low.  
Note: • Signal names listed in the second column of this table are not industry standard signal names. They  
are provided to assist in cross-referencing these signal names when they appear elsewhere.  
• Signals provided on the system interface port duplicate signals for connectors on the pen tablet. Do not  
use peripheral connectors on the pen tablet when using corresponding interfaces on the system  
interface port.  
System Interface Port  
51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
The port replicator/ mini-dock connector is not a “hot pluggable” connector. You must shut down or  
suspend the pen tablet before connecting the port replicator. The system interface port is disabled (all  
signals de-asserted) when system operation is suspended.  
Table 6-6. System Interface Port Connector Pin Assignments  
Signal  
Name  
Pin  
Level  
+16V  
Description  
DC Power Input  
Port or Connector  
DC-IN  
1
POW1  
2
POW1  
3
POW1  
4
POW1  
5
POW1  
6
POW1  
7
LOUTLG  
LOUTL  
5VMAIN  
5VMAIN  
5VMAIN  
5VMAIN  
FDSEL0#  
FMODE#  
FSIDE#  
VGAGND  
VGAGND  
VSYNC  
VGAB  
GND  
Analog  
+5V  
Ground Left  
Line Output Audio Jack  
Port Replicator  
8
Signal Left  
9
+5 Volt Power Output  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
Drive Select  
Density Select  
Head Select  
VGA Ground  
FDD  
CRT  
GND  
+5V  
Vertical Sync Signal  
DAC Blue Signal  
VGA Ground  
Analog  
GND  
VGAGND  
RTSA#  
DSRA#  
SMI  
RS-232C  
Request to Send  
Data Set Ready  
SMI Input  
Serial Port  
+3.3V  
+5V  
Port Replicator  
Parallel Port  
ID0  
Port Replicator ID Input  
Error  
PPERR#  
PAFD#  
PRD6  
Autofeed Output  
Port Data 6  
PRD5  
Port Data 5  
PRD0  
Port Data 0  
System Interface Port  
52  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Table 6-6. System Interface Port Connector Pin Assignments (Continued)  
Signal  
Name  
Pin  
30  
Level  
Description  
Port or Connector  
PC Card Slot  
B_D10  
PCMVCC  
Card Data 10  
Write Protect  
31  
32  
33  
34  
35  
36  
37  
38  
39  
40  
41  
42  
43  
44  
45  
46  
47  
48  
49  
50  
51  
52  
53  
54  
55  
56  
57  
58  
59  
60  
B_WP  
B_BVD1  
B_A0  
Battery Voltage Detect 1  
Card Address 0  
Card Address 1  
Card Reset  
B_A1  
B_RESET  
B_A6  
Card Address 6  
Card Address 15  
Card Address 22  
Ground  
B_A15  
B_A22  
GND  
GND  
Port Replicator  
PC Card Slot  
B_A19  
B_A11  
B_IORD#  
B_D7  
PCMVCC  
Card Address 19  
Card Address 11  
I/O Read  
Card Data 7  
GND  
GND  
Ground  
Port Replicator  
PC Card Slot  
B_D11  
B_D3  
PCMVCC  
Card Data 11  
Card Data 3  
GND  
GND  
LAN  
Ground  
Port Replicator  
LAN (RJ-45)  
GND  
LANTX-  
LANTX+  
GND  
Transmit Data  
GND  
--  
Ground  
Port Replicator  
Reserved  
DC-IN  
NC  
--  
POW1  
POW1  
POW1  
NC  
+16V  
DC Power Supply from Port Replicator  
--  
--  
Reserved  
SPOUT1  
LOUTR  
LOUTRG  
NC  
Analog  
Speaker Out  
Signal Right  
Ground Right  
--  
Speaker  
Line Output Audio Jack  
--  
Reserved  
System Interface Port  
53  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table 6-6. System Interface Port Connector Pin Assignments (Continued)  
Signal  
Name  
Pin  
61  
Level  
+5V  
Description  
+5V Power Output  
Port or Connector  
Port Replicator  
5VMAIN  
FWG#  
62  
63  
64  
65  
66  
67  
68  
69  
70  
71  
72  
73  
74  
75  
76  
77  
78  
79  
80  
81  
82  
83  
84  
Write Gate  
FDD  
FINDEX#  
5VMAIN  
FRDDT#  
VGAGND  
VGAGND  
DDCDATA  
VGAGND  
VGAGND  
RIA#  
Index  
+5V Power Output  
Read Disk Data  
VGA Ground  
Port Replicator  
FDD  
GND  
CRT  
+5V  
Serial data for VESA DDC2B monitor  
VGA Ground  
GND  
RS-232C  
+5V  
Ring Indicator  
Clear to Send  
Data Carrier Detect  
Keyboard Detect  
Printer Select Input  
Initiate Output  
Strobe Output  
Port Data 7  
Serial Port  
CTSA#  
DCDA#  
K-SW  
Keyboard  
PSLIN#  
PINIT#  
PSTB#  
PRD7  
Parallel Port  
GND  
GND  
Ground  
Port Replicator  
Parallel Port  
PC Card Slot  
PRD1  
+5V  
Port Data 1  
B_D0  
PCMVCC  
Card Data 0  
B_CD2#  
B_VS1  
GND  
Card Detect 2  
Voltage Sense 1  
Ground  
GND  
Port Replicator  
System Interface Port  
54  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table 6-6. System Interface Port Connector Pin Assignments (Continued)  
Signal  
Name  
Pin  
85  
Level  
Description  
Card Address 4  
Port or Connector  
PC Card Slot  
B_A4  
PCMVCC  
86  
B_A5  
Card Address 5  
Card Address 12  
Card Address 23  
Card Address 20  
Card Address 14  
Card Address 9  
I/O Write  
87  
B_A12  
88  
B_A23  
89  
B_A20  
90  
B_A14  
91  
B_A9  
92  
B_IOWR  
B_CE1#  
B_D15  
93  
Card Enable 1  
Card Data 15  
Card Data 12  
Card Data 4  
94  
95  
B_D12  
96  
B_D4  
97  
GND  
GND  
LAN  
Ground  
Port Replicator  
LAN (RJ-45)  
98  
GND  
99  
LANRX-  
LANRX+  
DETECT1  
USBGND  
USBGND  
USBGND  
USBGND  
SPOUT2G  
SPOUT2  
NC  
Receive Data  
100  
101  
102  
103  
104  
105  
106  
107  
108  
109  
110  
111  
112  
113  
114  
115  
+16V  
GND  
Core Unit Detect 1  
USB Ground  
Port Replicator  
USB  
Speaker Ground  
Speaker Out  
--  
Speaker  
Analog  
--  
Reserved  
NC  
FMOTOR#  
5VMAIN  
FSTEP#  
FWP#  
+5V  
Motor On  
FDD  
+5V Power Output  
Step  
Port Replicator  
FDD  
Write Protected  
+5V Power Output  
FDD Attach  
5VMAIN  
FDATCH#  
Port Replicator  
FDD  
System Interface Port  
55  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table 6-6. System Interface Port Connector Pin Assignments (Continued)  
Signal  
Name  
Pin  
Level  
GND  
Description  
Port or Connector  
116  
117  
118  
119  
120  
121  
122  
123  
124  
125  
126  
127  
128  
129  
130  
131  
132  
133  
134  
135  
136  
137  
138  
139  
140  
141  
142  
143  
144  
VGAGND  
VGAGND  
DDCCLK  
VGAG  
VGAGND  
NC  
VGA Ground  
CRT  
+5V  
Analog  
GND  
--  
Serial Clock for VESA DDC2B monitor  
DAC Green Signal  
VGA Ground  
--  
Reserved  
NC  
SINA  
RS-232C  
GND  
Receive Data  
Ground  
Serial Port  
GND  
Port Replicator  
Keyboard  
KDATA  
KCLOCK  
BUSY#  
PACK#  
PRD3  
+5V  
Keyboard Data  
Keyboard Clock  
Busy  
Parallel Port  
PC Card Slot  
Acknowledge  
Port Data 3  
PRD2  
Port Data 2  
B_D1  
PCMVCC  
Card Data 1  
Card Data 8  
Bus Cycle Wait  
Ready  
B_D8  
B_WAIT#  
B_READY  
B_A3  
Card Address 3  
Input Acknowledge  
Card Address 7  
Card Address 24  
Ground  
B_INPACK  
B_A7  
B_A24  
GND  
GND  
Port Replicator  
PC Card Slot  
B_WE#  
B_A8  
PCMVCC  
Write Enable  
Card Address 8  
Card Address 17  
Card Address 10  
Ground  
B_A17  
B_A10  
GND  
GND  
Port Replicator  
System Interface Port  
56  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table 6-6. System Interface Port Connector Pin Assignments (Continued)  
Signal  
Name  
Pin  
Level  
Description  
Port or Connector  
PC Card Slot  
145  
146  
147  
148  
149  
150  
151  
152  
153  
154  
155  
156  
157  
158  
159  
160  
161  
162  
163  
164  
165  
166  
167  
168  
169  
170  
171  
172  
173  
174  
175  
176  
B_D13  
PCMVCC  
Card Data 13  
Card Data 5  
B_D5  
PCMVCC  
PCMVCC  
PCMVCC  
DETECT0  
NC  
PCMVCC Power Supply  
+16V  
--  
Core Unit Detect 1  
Port Replicator  
Reserved  
USB  
--  
USBVCC  
USBVCC  
USBP+  
USBP-  
+5V  
USBVCC Power Supply  
USB DATA+  
USB DATA-  
USB Ground  
Ground  
USBGND  
GND  
GND  
+5V  
Port Replicator  
GND  
GND  
FDCHG#  
5VMAIN  
FDIR#  
Disk Change  
+5V Power Output  
Direction Control  
Track 00  
FDD  
Port Replicator  
FDD  
FTRK0#  
5VMAIN  
FWD#  
+5V Power Output  
Write Data  
Port Replicator  
FDD  
VGAGND  
VGAGND  
HSYNC  
VGAR  
GND  
VGA Ground  
CRT  
+5V  
Horizontal Sync Signal  
DAC Red Signal  
VGA Ground  
Analog  
GND  
VGAGND  
GND  
Ground  
Port Replicator  
Serial Port  
SOUTA  
DTRA#  
MCLOCK  
MDATA  
PCMVPP  
RS-232C  
+5V  
Transmit Data  
Data Terminal Ready  
Mouse Clock  
Mouse  
Mouse Data  
PCMVPP  
PCMVPP Power Supply  
PC Card Slot  
System Interface Port  
57  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table 6-6. System Interface Port Connector Pin Assignments (Continued)  
Signal  
Name  
Pin  
Level  
+5V  
Description  
Printer Selected Status  
Port or Connector  
Parallel Port  
177  
178  
179  
180  
181  
182  
183  
184  
185  
186  
187  
188  
189  
190  
191  
192  
193  
194  
195  
196  
197  
198  
199  
200  
PSLCT  
PPE  
Paper End  
GND  
GND  
Ground  
Port Replicator  
Parallel Port  
PC Card Slot  
PRD4  
B_D2  
+5V  
Port Data 4  
PCMVCC  
Card Data 2  
B_D9  
Card Data 9  
B_BVD2  
GND  
Battery Voltage Detect 2  
Ground  
GND  
Port Replicator  
PC Card Slot  
B_A2  
PCMVCC  
Card Address 2  
Attribute Memory Select  
Voltage Sense 2  
Card Address 25  
Card Address 16  
Card Address 21  
Card Address 13  
Card Address 18  
Output Enable  
Card Enable 2  
Card Data 14  
Card Data 6  
B_REG  
B_VS2  
B_A25  
B_A16  
B_A21  
B_A13  
B_A18  
B_OE#  
B_CE2#  
B_D14  
B_D6  
B_CD1#  
GND  
Card Detect 1  
Ground  
GND  
--  
Port Replicator  
Reserved  
NC  
--  
PCMVCC  
PCMVCC  
PCMVCC Power Supply  
PC Card Slot  
†
The Port Replicator Detect signal is grounded when the port replicator is attached. (Note that this is not a System  
Management Interrupt signal line on the microprocessor.)  
System Interface Port  
58  
Download from Www.Somanuals.com. All Manuals Search And Download.  
IrDA Port  
6
The IrDA port on the Stylistic 3500 pen tablet is compliant with the Infrared Data Association (IrDA)  
Standard Revision 1.1. Specifications for the IrDA port on the pen tablet are given in Table 6-7. Before you  
can use the IrDA port, the Serial Port B Device BIOS option must be set to IrDA or FIR. See “Serial/  
Parallel Port Configurations Submenu Options” on page 11 for details on BIOS options for the IrDA port.  
Table 6-7. IrDA Port Specifications  
Feature  
Specification  
Standard supported  
Distance  
IrDA Standard Revision 1.1  
Up to 1 meter point to point (environmental conditions affect usable range)  
Infrared rays (wavelength peak 875 nm)  
Conveyable wave  
Signal  
Send data / Receive data  
Modulation/Data Rate  
IrDA SIR: 9.6 - 115.2 Kbps  
IrDA FIR: 4,000.0 Kbps  
Angle  
0° to 15° from center of beam (30° viewing angle)  
Audio Jacks  
6
All audio jacks on the Stylistic 3500 pen tablet and Stylistic 3500 port replicator are stereo mini jacks.  
Some audio functions on the pen tablet are disabled when audio jacks are used. Table 6-8 shows which  
audio inputs are disabled when inputs on the pen tablet and port replicator or mini-dock are used  
(enabled). Table 6-9 shows which audio outputs are disabled when outputs on the pen tablet and port  
replicator are used.  
Table 6-8. Active Audio Inputs  
Pen Tablet  
Port Replicator/Mini-dock  
Input Activity  
Microphone  
(built-in)  
Microphone  
Input Jack  
Microphone  
Input Jack  
Line Input  
Jack  
Microphone On  
(microphone built into pen tablet)  
Enabled  
Plug not  
inserted  
Plug not  
inserted  
NA  
Pen tablet Microphone jack used  
(external microphone connected)  
Disabled  
Disabled  
NA  
Enabled  
Disabled  
NA  
Plug not  
inserted  
NA  
Port replicator Microphone jack used  
(external microphone connected)  
Enabled  
NA  
Port replicator Line In jack used  
NA  
Enabled  
NA indicates that the condition does not apply. (The condition has no effect on the given input.)  
IrDA Port  
59  
Download from Www.Somanuals.com. All Manuals Search And Download.  
               
Table 6-9. Active Audio Outputs  
Pen Tablet  
Port Replicator  
Output Activity  
Speaker  
(built-in)  
Headphone  
Jack  
Headphone  
Line Output  
Jack  
Jack  
Speaker On  
(speaker built into pen tablet)  
Enabled  
Plug not  
inserted  
Plug not  
inserted  
NA  
Pen tablet Headphone jack used  
(external headphone connected)  
Disabled  
Disabled  
NA  
Enabled  
Enabled  
Enabled  
NA  
NA  
Enabled*  
NA  
Port replicator Headphone jack used  
(external headphone connected)  
NA  
Port replicator Line Output jack used  
Enabled  
*
Using the headphone jacks on the pen tablet and port replicator at the same time is not recommended.  
“NA” indicates that the condition does not apply. (The condition has no effect on the given output.)  
Audio Jacks  
60  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
PC Card Port  
6
The PC Card socket is compliant with PC Card standard 3.0. Table 6-10 shows the pin assignments for the  
PC Card port. Table 6-2 illustrates the pin locations on the connector.  
Figure 6-2 PC Card Port Configuration  
30 31 32 33 34  
1
2
3
4
5
64  
66 67 68  
35 36 37 38 39  
65  
Table 6-10. PC Card Port Pin Assignments  
16-bit PC Card Interface  
Memory-Only I/O & Memory  
CardBus  
Pin  
1
2
3
4
5
6
7
8
9
GND  
D3  
GND  
D3  
GND  
CAD0  
D4  
D4  
CAD1  
D5  
D5  
CAD3  
D6  
D6  
CAD5  
D7  
D7  
CAD7  
CE1#  
A10  
OE#  
A11  
A9  
CE1#  
A10  
OE#  
A11  
A9  
CCBE0#  
CAD9  
CAD11  
CAD12  
CAD14  
CCBE1#  
CPAR  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
A8  
A8  
A13  
A14  
WE#  
READY  
VCC  
VPP1  
A16  
A15  
A13  
A14  
WE#  
IREQ#  
VCC  
VPP1  
A16  
A15  
CPERR#  
CGNT#  
CINT#  
VCC  
VPP1  
CCLK  
CIRDY#  
PC Card Port  
61  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Table 6-10. PC Card Port Pin Assignments  
16-bit PC Card Interface  
CardBus  
Pin  
21  
Memory-Only  
A12  
I/O & Memory  
A12  
CCBE2#  
22  
23  
24  
25  
26  
27  
28  
29  
30  
31  
32  
33  
34  
35  
36  
37  
38  
39  
40  
41  
42  
43  
44  
45  
46  
47  
48  
49  
50  
51  
52  
A7  
A7  
CAD18  
CAD20  
CAD21  
CAD22  
CAD23  
CAD24  
CAD25  
CAD26  
CAD27  
CAD29  
RFU  
A6  
A6  
A5  
A5  
A4  
A4  
A3  
A3  
A2  
A2  
A1  
A1  
A0  
A0  
D0  
D0  
D1  
D1  
D2  
D2  
WP  
GND  
GND  
CD1#  
D11  
D12  
D13  
D14  
D15  
CE2#  
VS1#  
RUF  
RFU  
A17  
A18  
A19  
A20  
A21  
VCC  
VPP2  
IOIS16#  
GND  
GND  
CD1#  
D11  
D12  
D13  
D14  
D15  
CE2#  
VS1#  
IORD#  
IOWR#  
A17  
A18  
A19  
A20  
A21  
VCC  
VPP2  
CCLKRUN#  
GND  
GND  
CCD1#  
CAD2  
CAD4  
CAD6  
RFU  
CAD8  
CAD10  
CVS1  
CAD13  
CAD15  
CAD16  
RFU  
CBLOCK#  
CSTOP#  
CDEVSEL#  
VCC  
VPP2  
PC Card Port  
62  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table 6-10. PC Card Port Pin Assignments  
16-bit PC Card Interface  
CardBus  
Pin  
53  
Memory-Only  
A22  
I/O & Memory  
A22  
CTRDY#  
54  
55  
56  
57  
58  
59  
60  
61  
62  
63  
64  
65  
66  
67  
68  
A23  
A23  
CFRAME#  
CAD17  
CAD19  
CVS2  
A24  
A24  
A25  
A25  
VS2#  
RESET  
WAIT#  
RFU  
REG#  
BVD2  
BVD1  
D8  
VS2#  
RESET  
WAIT#  
INPACK#  
REG#  
SPKR#  
STSCHG#  
D8  
CRST#  
CSERR#  
CREQ#  
CCBE3#  
CAUDIO  
CSTSCHG  
CAD28  
CAD30  
CAD31  
CCD2#  
GND  
D9  
D9  
D10  
D10  
CD2#  
GND  
CD2#  
GND  
PC Card Port  
63  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Hard Disk Drive Port  
6
Under ordinary circumstances, it is not necessary to access the hard disk drive port. The pin locations are  
listed in Table and illustrated in Figure in the event of hard disk replacement.  
Figure 6-3 Hard Disk Drive Pin Locations  
43 41 39 37 35 33 31 29 27 25 23 21 19 17 15 13 11  
30  
16 14 12  
9
7
8
5
6
3
4
1
2
44 42 40 38 36 34 32  
28 26 24 22 20 18  
10  
Table 6-11. Hard Disk Drive Pin Assignments  
HDD side  
Pin Number  
PCB side  
Pin Number  
Signal Name  
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
RESET#  
GND  
DATA7  
DATA8  
DATA6  
DATA9  
DATA5  
DATA10  
DATA4  
DATA11  
DATA3  
DATA12  
DATA2  
DATA13  
DATA1  
DATA14  
DATA0  
DATA15  
GND  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
10  
11  
12  
13  
14  
15  
16  
17  
18  
KEY  
19  
20  
21  
22  
DMARQ  
GND  
DIOW# / STOP  
GND  
Hard Disk Drive Port  
64  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Table 6-11. Hard Disk Drive Pin Assignments  
HDD side  
Pin Number  
PCB side  
Pin Number  
Signal Name  
25  
23  
DIOR# / HDMARDY# /  
HSTROBE  
26  
27  
24  
25  
GND  
IORDY / #DDMARDY /  
DSTROBE  
28  
29  
30  
31  
32  
33  
34  
35  
36  
37  
38  
39  
40  
41  
42  
43  
44  
26  
27  
CSEL#  
DMACK#  
GND  
28  
29  
30  
31  
32  
33  
34  
35  
36  
37  
38  
39  
40  
INTRQ  
IOCS16#  
DA1  
PDIAG#  
DA0  
DA2  
CS0#  
CS1#  
DASP#  
GND  
+5V (LOGIC)  
+5 V (MOTOR)  
GND  
RESERVE  
Hard Disk Drive Port  
65  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 7  
System Power  
This chapter covers the Stylistic 3500 pen tablet’s system power hardware, power management states,  
and state transitions.  
System Power Hardware  
7
The Stylistic 3500 pen tablet uses components designed for low power consumption in mobile  
applications. DC power, whether supplied by the battery pack or an external source, is regulated to  
different voltage levels required to power various components in the system.  
Battery Pack  
7
When the system is not connected to external power, system power is provided by the battery pack.  
When an external DC power source is connected to the pen tablet, the battery pack is charged and the  
system is powered by the external source.  
The battery pack can also be removed from the pen tablet and charged in an external charger. A bridge  
battery built into the pen tablet powers the system in suspend mode for approximately 5 minutes while  
the battery pack is removed.  
Note: Do not remove the battery pack while the system is running. Suspend system operation or shut down the  
system before removing the battery pack. The bridge battery will not power the system in the Fully On  
state.  
The pen tablet is equipped with a microcontroller, called the power management microcontroller unit  
(PMU), which is dedicated to managing battery pack power. The battery pack charge is monitored by the  
PMU. The PMU determines the percent of charge remaining in the battery pack, controls the battery level,  
and supplies battery status information to the system through a dedicated interface.  
A low voltage level detect circuit (independent of the PMU) measures the battery pack voltage level to  
determine whether the battery pack voltage has dropped to the critically low level (the critically low  
voltage varies depending on total current draw). When the system is running and the critically low  
voltage level is reached, the circuit forces the system into Suspend mode and the battery level window  
indicates the critically low condition.  
When the system is forced into Suspend mode by a critically low battery, the system is powered by the  
remaining charge in the battery pack or the bridge battery (whichever has the highest voltage). In this  
mode, the Suspend/ Resume button is disabled and system operation cannot be resumed until either an  
external DC power source is connected or a battery pack with adequate charge is installed.  
66  
Download from Www.Somanuals.com. All Manuals Search And Download.  
                 
DC Power Inputs  
7
External DC power can be connected at three locations on the pen tablet:  
• DC power connector on the pen tablet  
• System interface connector  
• DC input positions of the high-usage contacts  
A DC power source connected to any of these inputs must provide 3.36 amps at a continuous DC voltage  
of 16 volts ±10%. Specifications for the DC input connectors on the pen tablet and port replicator are  
given below.  
Table 7-1. DC Input Connectors  
Connector type  
EIAJ RC-5320A Type 5  
Hosiden  
Connector vendor  
Vendor part number*  
Pin assignments  
HEC3900-01-010  
Center conductor: +16 VDC ±10%  
Sleeve: ground  
* This is the part number for the female DC input connector on the pen tablet and the port replicator.  
System Power Hardware  
67  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Chapter 8  
BIOS Configuration Application Programming Interfaces  
This chapter describes application programming interfaces (APIs) that allow Windows applications to  
configure BIOS settings. These APIs include functions in the BIOSSET.DLL (dynamic-link library).  
This DLL includes functions that can be called from Windows applications to configure BIOS parameters  
for the Stylistic 3500 pen tablet.  
To use these functions with your applications:  
• Include the header file BIOSINC.H in your program source code.  
• Ensure that the BIOSSET.DLL file is in the C:\ WINDOWS\ SYSTEM directory on your system at run  
time.  
The DLL files are available on-line and can be downloaded from the Fujitsu PC web site at:  
www.fujitsupc.com  
Function prototypes for these APIs are written in the C programming language and are described in this  
guide using C syntax. Although ideally suited for program development using a compiler that supports  
the ANSI C or C++ standard, these functions can be called from applications developed in other  
programming languages, such as Microsoft Visual Basic, which allow you to use DLLs. Refer to the  
documentation for your programming language for details on calling functions in DLLs.  
Version Information  
8
Version information for the DLL can be obtained by calling the GetFileVersionInfo and  
GetFileVersionInfoSize functions supplied in the Microsoft Visual C++ development library.  
Note: Version information can also be viewed by selecting the file and carrying out the Properties command in  
Windows.  
Summary of Functions  
8
A summary of functions you should be familiar with to use this API is given below:  
• InitializeBIOS  
This function initializes the API. This function must be called before any other functions in this API  
can be called.  
• UpdateBIOSCheckSum  
Applications which use this API must call this function to close the API before the application exits.  
• ReadBIOSSettings  
This function retrieves BIOS settings for a BIOS option that you specify.  
• BiosSetupSet  
This function sets the BIOS setting that you specify.  
68  
Download from Www.Somanuals.com. All Manuals Search And Download.  
               
Note: Parameter names given in this manual in prototypes for some of these functions may differ from  
parameter names given in the prototypes that appear in the header files. This is done to provide consistent  
terminology throughout this manual.  
InitializeBIOS  
8
This function initializes the API. This function must be called before any other functions in this API can  
be called. This function,  
• Opens the API.  
• Connects to the APM BIOS.  
A prototype of this function is shown below:  
intInitializeBIOS(void)  
This function accepts no parameters and returns the value SETUP_SUCCESS when it completes  
successfully. If an error occurs, this function returns an error value as defined in Table 8-1.  
UpdateBIOSCheckSum  
8
Applications that initialize this API using InitializeBIOS must call this function before the application  
exits. This function performs the following tasks:  
• Updates the CMOS checksum and CRC values.  
• Disconnects from the APM BIOS.  
A prototype of this function is shown below:  
intUpdateBIOSCheckSum(void)  
This function accepts no arguments and returns the value SETUP_SUCCESS when it completes  
successfully. If an error occurs, this function returns an error value as defined in Table 8-1.  
ReadBIOSSettings  
8
This function retrieves the setting for a given BIOS option. You define the BIOS option to be retrieved by  
passing the appropriate parameters for the desired option. A prototype is shown below:  
DWORDReadBIOSSettings(DWORDdwSetupParam)  
The Option parameter defines the BIOS option you want to retrieve. Definitions for the Option parameter  
are listed in Table 8-2 later in this section.  
On success, this function returns the Setting for the requested BIOS option. See Table 8-2 for a listing of  
settings for each BIOS option. Possible error codes returned by this function are listed in Table 8-1.  
BiosSetupSet  
8
This function sets the BIOS option you specify. A prototype of the function is shown below:  
intBiosSetupSet(DWORDdwSetupParam,intnValue)  
The Option parameter defines the BIOS option you want to set. The Setting parameter defines the setting  
for the given option. Definitions for the Option parameter are listed in Table 8-2 on page 70.  
InitializeBIOS  
69  
Download from Www.Somanuals.com. All Manuals Search And Download.  
               
On success, this function returns the label SETUP_SUCCESS. In the event of an error, this function  
returns one of the error codes listed in Table 8-1.  
Error Codes  
8
Error codes returned by functions in this API are given in Table 8-1.. These values are defined in the  
header file BIOSINC.H.  
Table 8-1. BIOS Configuration API Error Codes  
Return Value  
Description  
SETUP_INVALID_PARAMETER The Option parameter is out of range. The value passed does not  
specify a valid BIOS option.  
SETUP_INTERNAL_ERROR  
Windows system call failure.  
Option and Setting Parameters  
8
Option and Setting parameters accepted by the functions described in this chapter are defined in the  
header file for the DLL. Table 8-2 lists the Option parameter and corresponding Setting parameters for  
each BIOS option. (These Setting parameters are also the values returned by the ReadBIOSSettings function  
on success.)  
Table 8-2. Option and Setting Parameters and Return Values  
Option Parameter  
Option Description  
Setting Parameter  
Setting Description  
Enabled  
SERIAL_PORT  
SERIAL_PORT_ON  
SERIAL_PORT_OFF  
SERIAL_PORT_AUTO  
Disabled  
Serial Port  
Auto  
SERIAL_ADDRESS  
Serial Port Address  
SERIAL_ADD_2E8  
SERIAL_ADD_2F8  
SERIAL_ADD_3E8  
SERIAL_ADD_3F8  
SER_INT_IRQ3  
I/ O Address 2E8  
I/ O Address 2F8  
I/ O Address 3E8  
I/ O Address 3F8  
IRQ 3  
SERIAL_INTERRUPT  
Serial Port Interrupt  
SER_INT_IRQ4  
IRQ 4  
INFRARED_PORT  
INFRARED_PORT_ON  
INFRARED_PORT_OFF  
INFRARED_PORT_AUTO  
Enabled  
Disabled  
Auto  
Infrared Port  
INFRARED_ADDRESS  
Infrared Port Address  
INFRA_ADD_2E8  
INFRA_ADD_2F8  
INFRA_ADD_3E8  
INFRA_ADD_3F8  
I/ O Address 2E8  
I/ O Address 2F8  
I/ O Address 3E8  
I/ O Address 3F8  
INFRARED_INTERRUPT  
INFRA_INT_IRQ3  
INFRA_INT_IRQ4  
IRQ 3  
IRQ 4  
Infrared Port Interrupt  
Error Codes  
70  
Download from Www.Somanuals.com. All Manuals Search And Download.  
           
Table 8-2. Option and Setting Parameters and Return Values (Continued)  
Option Parameter  
Option Description  
Setting Parameter  
INFRA_DEV_FIR  
INFRA_DEV_IRDA  
Setting Description  
INFRARED_MODE  
FIR  
IrDA (SIR mode)  
Infrared Device Mode  
INFRARED_SEC_ADDRS  
Secondary Infrared Address  
INFRA_ADD_100  
INFRA_ADD_108  
INFRA_ADD_110  
INFRA_ADD_118  
I/ O Address 100  
I/ O Address 108  
I/ O Address 110  
I/ O Address 118  
INFRARED_DMA  
INFRA_DMA_DMA1  
INFRA_DMA_DMA3  
DMA Channel 1  
DMA Channel 3  
Infrared Direct Memory Access  
(DMA) Channel  
PARALLEL_PORT  
PARALLEL_PORT_ON  
PARALLEL_PORT_OFF  
PARALLEL_PORT_AUTO  
Enabled  
Disabled  
Auto  
Parallel Port  
PARALLEL_ADDRESS  
PAR_ADD_278  
PAR_ADD_378  
PAR_ADD_3BC  
I/ O Address 278  
I/ O Address 378  
I/ O Address 3BC  
Parallel Port Address  
PARALLEL_INTERRUPT  
Parallel Port Interrupt  
PAR_INT_IRQ3  
PAR_INT_IRQ4  
IRQ 3  
IRQ 4  
PAR_INT_IRQ7  
IRQ 7  
PARALLEL_MODE  
Parallel Port Mode  
PAR_MODE_BID  
PAR_MODE_ECP  
Bidirectional  
Extended Capabilities  
Port  
PAR_MODE_OUTP  
Output Only  
PARALLEL_DMA  
PAR_DMA_DMA1  
PAR_DMA_DMA3  
DMA Channel 1  
DMA Channel 3  
Parallel Port ECP DMA Channel  
KBD_MOU_PLUG  
KBD_MOU_PLUG_ON  
KBD_MOU_PLUG_OFF  
Enabled  
Disabled  
Keyboard/ Mouse Hot Plug  
MODEM_CONTROLLER  
MODEM_ENB  
MODEM_DIS  
Enabled  
Disabled  
Internal Modem  
DISPLAY  
DISP_INT  
DISP_EXT  
DISP_BOT  
LCD  
External Monitor  
Both  
Display  
Option and Setting Parameters  
71  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table 8-2. Option and Setting Parameters and Return Values (Continued)  
Option Parameter  
Option Description  
Setting Parameter  
Setting Description  
COMPENS  
DISP_ENB  
Enabled  
DISP_DIS  
Disabled  
Expand VGA Screen  
HOT_PAD  
Hotpad  
HP_ENABLE  
HP_DISABLE  
Enabled  
Disabled  
HD_SECTOR  
BS_NORM  
BS_WP  
Normal  
Write Protect  
Hard Disk Boot Sector  
THERMAL_CNTR  
Thermal Controller  
THERMAL_CPU  
THERMAL_FAN  
CPU thermal control  
Fan thermal control  
FLOPPY_CONTROLLER  
FLPY_ENB  
FLPY_DIS  
Enabled  
Disabled  
Floppy Disk Drive Controller  
LAN_CONTROLLER  
LAN Controller  
LAN_ENB  
LAN_DIS  
Enabled  
Disabled  
Auto  
LAN_AUTO  
IDE_CONTROLLER  
IDE Controller  
IDE_ENB  
IDE_DIS  
Enabled  
Disabled  
SR_SWITCH  
SR_ENABLE  
SR_DISABLE  
Enabled  
Disabled  
Suspend/ Resume Switch  
QUICK_BOOT  
QUICK_ENABLE  
QUICK_DISABLE  
Enabled  
Disabled  
QuickBoot Mode  
QUICK_AUTO  
Auto  
DIAG_SCREEN  
DIAG_ENABLE  
DIAG_DISABLE  
Enabled  
Disabled  
Boot-time Diagnostic Messages  
EXEC_ENVRN  
SETUP_ENABLE  
SETUP_DISABLE  
Enabled  
Disabled  
Pre-Boot Execution Environment  
NUM_LOCK  
Numlock  
NUM_ON  
On  
NUM_OFF  
NUM_AUTO  
Off  
Auto  
Option and Setting Parameters  
72  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Chapter 9  
Programmable Hotpad Libraries for Windows Applications  
This chapter provides details on using libraries that allow Windows applications to use the  
programmable hotpad on the pen tablet.  
Note: The library files and the header file referenced in this chapter can be downloaded from the Fujitsu PC  
website: www.fujitsupc.com  
The following two libraries allow you to use the programmable hotpad with your applications:  
• HOTPAD.DLL  
A dynamic-link library.  
• HOTPAD.LIB  
A static library which allows your application to link to HOTPAD.DLL.  
Functions described in this chapter are the same for both of these libraries. Use one of these libraries  
depending on whether you want to use dynamic or static linking in your application.  
To use dynamic linking:  
• Include the header file HOTPAD.H in the program code for your application.  
• The file HOTPAD.DLL must be in the C:\ WINDOWS\ SYSTEM directory at run time.  
To use static linking:  
• Include the file HOTPAD.LIB in your program code.  
• The file HOTPAD.DLL must be in the C:\ WINDOWS\ SYSTEM directory at run time.  
Note: The DLL is still used at run time when you use static linking. Using static linking resolves calls to the  
DLL when your program is compiled.  
Hotpad Notification  
9
Applications using this DLL are notified when a hotpad event occurs (when the programmable hotpad is  
tapped) using a notification message sent to the window procedure of the application.  
Hotpad notification is enabled and disabled using the following functions:  
• SetHotpadNotification  
This function enables hotpad notification for the calling application.  
• KillHotpadNotification  
This function disables hotpad notification for the calling application.  
These functions are described in the following sections.  
Note: Hotpad notification using a call-back function is not supported by HOTPAD.DLL.  
73  
Download from Www.Somanuals.com. All Manuals Search And Download.  
         
SetHotpadNotification  
9
This function enables hotpad notification. Applications which are to receive notification of hotpad events  
must call this function once to enable hotpad notification. A prototype of this function is shown below:  
intSetHotpadNotification(HWNDWindowHandle,UINTMessageID)  
Parameters this function accepts are described below:  
Parameter  
Description  
WindowHandle  
Handle to the application window that will receive hotpad  
notification messages.  
MessageID  
Message ID of the notification message that will be sent to the  
calling application window when a hotpad event occurs.  
Return values for SetHotpadNotification are as follows:  
Return Value  
Description  
Positive nonzero integer  
Hotpad notification ID. Returned on success.  
The library assigns a unique hotpad notification ID number for each  
occurrence of the SetHotpadNotification function. Your application  
must pass this ID number when hotpad notification is disabled  
using the KillHotpadNotification function.  
0
Memory allocation failure.  
-1  
-2  
WindowHandle parameter not valid.  
Could not allocate system timer.  
KillHotpadNotification  
9
This function disables hotpad notification for your application. Programs which have enabled hotpad  
notification should call this function before exiting or when hotpad notification is no longer desired. A  
prototype of this function is shown below:  
BOOLKillHotpadNotification(intNotificationID)  
You must pass the hotpad notification ID number that was returned by SetHotpadNotification as the  
NotificationID parameter. Note that this function disables hotpad notification for the calling application  
only. Other applications which have enabled hotpad notification will continue to receive hotpad  
notification. Return values for this function are as follows:  
Return Value  
Description  
TRUE  
Returned if the function is successful. Hotpad notification is  
disabled.  
FALSE  
Returned if the function fails.  
This function will fail if the NotificationID parameter is not a valid  
hotpad notification ID.  
SetHotpadNotification  
74  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Appendix A  
Replacing the IDE Hard Disk Drive  
The internal IDE hard disk drive in the Stylistic 3500 pen tablet can be removed and replaced, if  
necessary.  
Caution  
Observe the following guidelines when handling the hard disk drive:  
• Do not attempt to disassemble or modify the hard disk drive.  
• Do not remove any labels from the hard disk drive.  
• HDD replacement should only be performed at a static-free workstation.  
Avoid touching connector pins and circuit boards on the drive or pen tablet.  
Electrostatic discharge caused by doing so can damage sensitive  
components.  
Removing the Hard Disk Drive  
9
To remove the hard disk drive from the pen tablet,  
1. Ensure that the pen tablet is off. To do so, carry out the Shut Down command in the Start menu.  
2. Using a Phillips screw driver (size #1), remove the two screws in the hard disk drive cover plate and  
remove it as shown in Figure A-1:.  
Figure A-1: IDE Hard Disk Drive Cover Plate  
75  
Download from Www.Somanuals.com. All Manuals Search And Download.  
               
3. Carefully disconnect the small connector by pulling upwards (reference Figure A-2:). Use care when  
disconnecting this connector; it is attached to a delicate flex cable.  
Caution  
• Do not pull the tab on the flex cable connector when lifting  
the drive. Doing so will damage the flex cable; it is fragile  
and has very little slack.  
• Be careful not to damage the hard disk drive’s printed  
circuit board when removing the drive. Handle the drive by  
the edges and avoid touching the printed circuit board with  
your hands or tools.  
Figure A-2: Unplugging the Hard Disk Drive Connector  
Removing the Hard Disk Drive  
76  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
4. Using your thumbs, push back on the two corners of the hard drive at the locations indicated in Figure  
A-3:. Using firm pressure, push the hard disk drive towards the edge of the system. The small foam  
inserts on the end of the hard disk tray offer sufficient “give” for the drive to be removed without  
damaging the flex cable.  
Foam inserts  
Figure A-3: Removing the Hard Disk Drive, Part 1  
5. While pushing back on the hard drive, lift the connector end out of the tray, as illustrated in Figure  
A-4.  
Figure A-4: Removing the Hard Disk Drive, Part 2  
6. Remove the hard drive from the tray, as illustrated in Figure A-5. Once the hard disk drive has been  
removed from the pen tablet, you can install a new hard disk drive. If you are returning the hard disk  
drive for repair, ensure that the packaging material will protect the drive sufficiently during shipment.  
Removing the Hard Disk Drive  
77  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Flex Cable Connector  
Flex Cable  
Foam Insert  
Connector  
Unused pins  
Figure A-5: Installing the IDE Hard Disk Drive  
Installing the Hard Disk Drive  
9
To install the hard disk drive, refer to Figures A-1 through A-5, and perform the following steps:  
1. Connect the flex cable to the hard disk drive and fold the tab on the flex cable down under the flex  
cable as shown in Figure A-5:. Note the orientation of the hard disk drive and note that four pins on  
the hard disk drive connector are not used. (The connector on the flex cable is keyed so it cannot be  
installed incorrectly.)  
2. Ensure that the plastic liner tray is in place and insert the hard disk drive into the pen tablet. Note that  
the liner tray is installed between the hard disk drive and surrounding surfaces of the pen tablet to  
prevent the shock mount pads from sticking to the hard disk drive.  
3. Follow the steps contained in the section entitled “Removing the Hard Disk Drive” in reverse order.  
Use care when installing the drive to prevent damage to the flex cable.  
The hard disk drive is now installed in the pen tablet.  
Installing the Hard Disk Drive  
78  
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Appendix B  
AT Command Set  
This Appendix contains a summary of AT commands used by the Stylistic 3500 pen tablet’s modem.  
There are several things to note about this set of commands:  
• Commands should be entered as ASCII characters.  
• Commands should begin with “AT”, with a description of the character after the “AT”.  
• The commands are not case-sensitive; upper and lower case characters are treated the same.  
• All commands should be followed by the “CR” character stored in “S3”.  
• Spaces are counted as characters.  
• Command indication can be a selected letter or number message, or it can be no return message by  
designation.  
• Data format is as follows:  
Start bit  
Data bit  
Parity  
Stop bit  
1
7
even  
1
1
1
1
7
7
8
odd  
none  
none  
1
2
1
Note: Baud rate and data format are detected by the “AT” character.  
79  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
AT Commands Table  
9
AT Data Commands  
9
The shaded portion of the table are stored with the AT&W command.  
Command  
Specification  
Default  
A/  
A
Repeat last command.  
Answer command.  
Dial  
D
T
123456789*0#ABCD  
3
P
1234567890  
W
Wait for dial tone. Modem waits for a second dial tone before processing the  
dial string.  
@
Wait for quiet answer.  
‘
Pause for a time specified by S8 before dialing.  
Hook flash  
!
;
Return to command mode after processing command.  
S=n  
Dial a telephone number previously stored using the &Zn=x command. The  
range of n is 0-3.  
E
H
I
0
1
Disables echo to the computer  
Enables echo to the computer  
3
3
0
Modem goes on-hook  
1
0
1
2
Modem goes off-hook  
Returns modem identity string and driver version number, same as I3  
Calculates ROM checksum and displays it on the DTE.  
Performs a ROM check and calculates and verifies the checksum, displaying  
OK or ERROR.  
3
0
1
2
Returns modem identity string and driver version number, same as I0  
Selects low volume.  
L
Selects low volume.  
Selects medium volume.  
3
3
3
0
1
Selects high volume.  
M
The speaker is off.  
The speaker is on until the modem detects the carrier signal.  
2
3
The speaker is always on when modem is off-hook.  
The speaker is on until the carrier is detected, except while dialing.  
AT Commands Table  
80  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Command  
Specification  
Default  
N
O
0
When originating or answering, this is for handshake only at the  
communication standard specified by S7 and the ATB command.  
1
0
When originating or answering, begin the handshake only at the  
communication standard specified by S7 and the ATB command. During  
handshake, fallback to a lower speed may occur.  
3
Instructs the modem to exit online command mode and return to data mode  
(see AT Escape Sequence, +++).  
P
Select Pulse Dialing.  
Q
0
1
Enables modem to send result codes to the computer.  
3
3
Disables modem from sending result codes to the computer.  
Select Tone Dialing.  
T
V
0
1
Displays results codes as digits.  
Displays results codes as text.  
X
Result Code Selection and Call Progress Monitoring  
Dialing  
After S6  
Result Code  
No Dialtone  
Not displays  
Busy Code  
Displays  
“CONNECT”  
0
1
2
Not displays  
Displays  
“CONNECTXXX”  
After S6  
Not displays  
Displays  
Not displays  
Not displays  
Displays  
“CONNECTXXX”  
Wait Dial Tone  
(S6)  
Displays  
“CONNECTXXX”  
3
4
After S6  
Not displays  
Displays  
Displays  
Displays  
Displays  
“CONNECTXXX”  
Wait Dial Tone  
(S6)  
3
3
3
Z
Reset and recall stored user profile.  
&C  
0
1
State of the carrier from remote modem is ignored. DCD circuit is always on.  
DCD turns on when the remote modem’s carrier signal is detected, and off  
when the carrier signal is not detected.  
&D  
0
1
2
Ignores status of DTR signal.  
Enters command state upon On-to-Off transition of DTR.  
Goes on hook upon On-to-Off transition of DTR.  
3
Goes on hook and resets upon On-to-Off transition of DTR.  
Recall factory setting as active configuration.  
Disable flow control.  
&F  
&K  
0
3
Enable RTS/CTS (hardware) flow control.  
3
4
Enable XON/XOFF flow control.  
AT Commands Table  
81  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Command  
Specification  
Default  
3
&P  
0
1
39% make/break ratio. 10PPS  
33% make/break ratio. 10PPS  
2
0
33% make/break ratio. 20PPS  
DSR always ON.  
&S  
3
1
DSR comes on when establishing a connection and goes off when the  
connection ends.  
&T  
&V  
0
1
Abort. Stops any test in progress.  
Local analog loop.  
View active configuration and stored profile.  
Store current configuration  
&W  
&Zn  
/A  
Store telephone number. (n=0, 1, 2, 3)  
Sets MNP block size max. 64 characters  
Sets MNP block size max. 128 characters  
Sets MNP block size max. 192 characters  
Sets MNP block size max. 256 characters  
0
1
2
3
3
3
/Bn  
/K  
Transmit break to remote. /B1-/B9 break length in 100ms units.  
1) Receives break from the DTE when on-line mode.  
5
0, 2, 4  
Enter on-line command mode, no break set to remote.  
1
3
5
Clear data buffers and send break to remote modem  
Send break to remote modem immediately.  
Send break to remote modem in sequence with transmitted data.  
2) On-line command mode during a data connection. The /B is received in order to  
send a break to the remote.  
0, 1  
2, 3  
4, 5  
Clear data buffers and send break to remote modem.  
Send break to remote modem immediately.  
Send break to remote modem in sequence with data.  
3) Break is received from a remote modem during on-line mode.  
0, 1  
2, 3  
4, 5  
Clears data buffers and sends break to the DTE.  
Send a break immediately to the DTE.  
Send a break in sequence with received data to the DTE.  
AT Commands Table  
82  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Command  
Specification  
Default  
/N  
0
1
2
3
Normal speed-buffered mode.  
Direct mode (if parallel I/F is selected, same as /NO).  
MNP reliable mode (MNP -> disconnect)  
Auto-reliable mode (LAPM -> MNP -> NORMAL -> disconnect).  
Same as /N5.  
3
4
5
LAPM-reliable mode (LAPM -> disconnect)  
Auto-reliable mode (LAPM -> MNP -> NORMAL -> disconnect).  
Same as /N3.  
/V  
/X  
0
1
Disable protocol result code appended to DCE speed.  
Enable protocol result code appended to DCE speed.  
3
3
2
0
Same as /V1.  
Do not pass XON/XOFF flow control characters.  
1
Pass XON/XOFF flow control characters.  
-V90=<n>  
=0  
=1  
Disable V.90  
Enable V.90 Auto Rate  
3
=2  
Attempt to connect at 28000 bit/s  
Attempt to connect at 29333 bit/s  
Attempt to connect at 30666 bit/s  
Attempt to connect at 32000 bit/s  
Attempt to connect at 33333 bit/s  
Attempt to connect at 34666 bit/s  
Attempt to connect at 36000 bit/s  
Attempt to connect at 37333 bit/s  
Attempt to connect at 38666 bit/s  
Attempt to connect at 40000 bit/s  
Attempt to connect at 41333 bit/s  
Attempt to connect at 42666 bit/s  
Attempt to connect at 44000 bit/s  
Attempt to connect at 45333 bit/s  
Attempt to connect at 46666 bit/s  
Attempt to connect at 48000 bit/s  
Attempt to connect at 49333 bit/s  
Attempt to connect at 50666 bit/s  
Attempt to connect at 52000 bit/s  
=3  
=4  
=5  
=6  
=7  
=8  
=9  
=10  
=11  
=12  
=13  
=14  
=15  
=16  
=17  
=18  
=19  
=20  
AT Commands Table  
83  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Command  
Specification  
Default  
=21  
=?  
?
Attempt to connect at 53333bit/s  
Shows the current value.  
Shows the range [0-21]  
%C  
0
1
V.42bis/MNP5 disable. No data compression.  
V.42bis/MNP5 enable. Data compression enabled.  
3
3
%E  
0
1
2
Disable line quality monitor and auto-retrain.  
Enable line quality monitor and auto-retrain.  
Enable line quality monitor and fall back/fall forward.  
AT Commands Table  
84  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AT Fax (Class1) Commands  
9
Command  
Specification  
Service class indication (*1)  
Default  
+FCLASS  
?
=n  
Service class selection (*2)  
3
=?  
=n  
=n  
=n  
=?  
=n  
=?  
=n  
=?  
=n  
=?  
Service class capabilities (*2)  
+FTS  
+FRS  
+FTM  
Transmission silence (n=0-255, 10ms intervals)  
Receive silence. (n=0-255, 10ms intervals)  
Transmit FAX data with <n> carrier.  
Transmit FAX modulation. (*3)  
+FRM  
+FTH  
+FRH  
Receive FAX with <n> carrier.  
Receive FAX modulation. (*3)  
Transmit HDLC data with <n> carrier.  
Transmit HDLC data modulation (*3).  
Receive HDLC data with <n> carrier.  
Receive HDLC data modulation. (*3).  
*1:  
000 -> Data mode  
*2:  
0 -> Data mode  
001 -> Facsimile Class 1  
008 -> Voice Mode  
1 -> Facsimile Class 1  
8 -> Voice Mode  
080 -> VoiceView Mode (not supported)  
80 -> VoiceView Mode (not supported)  
*3: Modulation by parameter  
3: V.21 Channel2  
24: V.27ter  
48: V.27ter  
72: V.29  
300bps  
2400bps  
4800bps  
7200bps  
73: V.17  
7200bps (long  
7200bps (short)  
9600bps  
74: V.17  
96: V.29  
97: V.17  
9600bps (long  
9600bps (short)  
12000bps (long)  
12000bps (short)  
14400bps (long)  
14400bps (short)  
98: V.17  
121: V.17  
122: V.17  
145: V.17  
146: V.17  
9
AT Commands Table  
85  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
V.25ter AT Commands  
9
Command  
Specification  
Return ‘Lucent Data/Fax’  
Description  
+GMI  
Manufacturer Identification  
Version/Revision Information  
Modem Identification  
+GMR  
+GMM  
Return Lucent driver version number (e.g., 5.54)  
Return ‘H.324 video-ready rev. 1.0’  
AT+A8E=<v80>  
v8o  
1: The default value disables the CI origination  
option while in V.8 negotiation. However, the  
modem, when initiating the call as a data call,  
detects ANSam and is capable of starting in  
V.34 mode.  
Defined for two conditions: as a  
parameter to configure V.8  
originating and answering  
operation while the DCE is  
on-hook.It initiates an action if  
the DCE is off-hook. If enabled,  
V.8 negotiation does not  
preclude simultaneous  
6: Enables DCE control of V.8 and CI option.  
implementation of other  
negotiation means like V.8bis,  
V.18, or V.32bis.  
v8a  
1: The default value disables the CI option while  
in V.8 negotiation. However, the modem,  
when answering a call, sends the ANSam  
and is capable of starting in V.34 mode.  
5: Enables DCE control of V.8 and CI option.  
v8cf  
21h: Call function for H.324 calls.  
c1h: Call function for DSVD calls.  
AT+A8E?  
Report current values of  
subparameter.  
AT+A8E=?  
Report supported ranges of  
values <v8o>, <v8a>, <v8cf>  
+A8I:<v8cf><CR>  
This indication is used by an  
answering DCE if +A8E,  
<v8a>!=0, to indicate detection of  
a V.8 CI signal, and report the  
recovered Call Function octet(s).  
Value <v8cf> is a hexadecimal  
code octet that can take values  
as shown above in +A8E  
command.  
+A8M=<hexadecimal  
coded CM or JM octet  
string>  
Refer to V.8 document for coding.  
Directs the DCE to send a V.8  
CM or JM signal using the  
specified hexadecimal coded  
string.  
+A8A:<type><CR>  
1: Indicates V.8 ANSam signal flags.  
0: Indicates no ANSam signal detected.  
AT Commands Table  
86  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
S Register Table  
9
Default is North America. The shaded portions of the table are stored with AT&W command.  
Reg  
S0  
Function  
Units  
Default  
Range  
*
Auto answer ring number  
Rings  
000  
000-255  
*JP000-015  
000-255  
S1  
S2  
S3  
S4  
S5  
S6  
Ring counter. Read only.  
Escape character  
Rings  
ASCII  
ASCII  
ASCII  
ASCII  
sec  
000  
043  
013  
010  
008  
002  
000-128  
**  
**  
**  
*
Carriage return character (CR)  
Line feed character (LF)  
Backspace character (BS)  
Wait time for dial tone.  
000-127  
000-127  
000-032  
002-065  
*JP  
004  
*JP004-065  
*
S7  
Wait time for dial tone.  
sec  
sec  
050  
001-255  
*JP035-059  
002-065  
*
*
*
S8  
Pause for dial delay modifier “,”.  
Carrier loss Disconnect time.  
DTMF Dialing speed.  
002  
S10  
S11  
100ms 020  
001-255  
1ms  
095  
050-150  
*JP70-150  
000-255  
S12  
S14  
Escape prompt delay.  
20ms  
050  
General bit mapped options status. (Read only)  
0: Enable short form result codes  
1: Enable long form result codes.  
ATV0  
ATV1  
Bit 3  
Bit 6  
3
0: 10PPS  
AT&P0,  
&P1  
3
1: 20PPS  
AT&P2  
S21  
General bit mapped options status (Read only)  
0: DTR behavior.  
AT&D0  
AT&D1  
AT&D2  
Bits 4, 3  
1: DTR behavior.  
2: DTR behavior.  
3
3: DTR behavior.  
0: DCD behavior.  
1: DCD behavior.  
AT&D3  
Bit 5  
“*”  
: These S-registers are country-specific.  
“**” : These return to default value by &W command  
“*JP” : Default for Japan mode  
S Register Table  
87  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
S22  
Results bit mapped options status (Read only)  
0: Displays “CONNECT”  
ATX0  
ATX1  
ATX2  
ATX3  
ATX4  
Bits 6-4  
4: Displays “CONNECT xxx”  
5: ATX1 mode + dial tone detection  
6: ATX1 mode + busy tone detection  
7: ATX1 mode + dial & busy tone detection  
3
3
0: 33% Make/Break ratio  
AT&P1,  
&P2  
Bit 7  
1: 39% Make/Break ratio  
AT&P0  
S24  
S37  
Timer to control sleep mode.  
000 = disable  
sec  
010  
000,  
005-065  
Dial line rate.  
=0  
Maximum modem speed  
3
=1  
Reserved  
=2  
1200 bits/s and 75 bits/s  
300 bits/s  
=3  
=4  
Reserved  
=5  
1200 bits/s  
=6  
2400 bits/s  
=7  
4800 bits/s  
=8  
7200 bits/s  
=9  
9600 bits/s  
=10  
=11  
=12  
=13  
=14  
=15  
=16  
=17  
=18  
=19  
12000 bits/s  
14400 bits/s  
16800 bits/s  
19200 bits/s  
21600 bits/s  
24000 bits/s  
26400 bits/s  
28800 bits/s  
31200 bits/s  
33600 bits/s  
S Register Table  
88  
Download from Www.Somanuals.com. All Manuals Search And Download.  
S38  
56K Dial Line Rate  
=0  
=1  
56K disabled  
3
56K enabled - automatic speed selection - maximum  
modem speed.  
=2  
32000 bits/s  
34000 bits/s  
36000 bits/s  
38000 bits/s  
40000 bits/s  
42000 bits/s  
44000 bits/s  
46000 bits/s  
48000 bits/s  
50000 bits/s  
52000 bits/s  
54000 bits/s  
56000 bits/s  
=3  
=4  
=5  
=6  
=7  
=8  
=9  
=10  
=11  
=12  
=13  
=14  
S91  
Line Transmit Level.  
-dBm  
14  
9-15  
This register is effective only for Japan.  
S Register Table  
89  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Result Codes Summary  
9
Result Code  
Numeric  
Description  
OK  
0
1
2
3
Command executed.  
CONNECT  
RING  
Modem connected to line.  
A ring signal has been detected.  
NO CARRIER  
Modem lost carrier signal, or does not detect carrier  
signal, or does not detect answer tone.  
ERROR  
4
Invalid command.  
NO DIALTONE  
6
No dial tone detected.  
BUSY  
7
Busy signal detected.  
NO ANSWER  
8
No quiet answer.  
CONNECT 2400 EC*  
CONNECT 4800 EC*  
CONNECT 9600 EC*  
CONNECT 14400 EC*  
CONNECT 19200 EC*  
CONNECT 7200 EC*  
CONNECT 12000 EC*  
CONNECT 16800 EC*  
CONNECT 300 EC*  
CONNECT 21600 EC*  
CONNECT 24000 EC*  
CONNECT 26400 EC*  
CONNECT 28800 EC*  
CONNECT 31200 EC*  
CONNECT 33600 EC*  
CONNECT 38400 EC*  
CONNECT 57600 EC*  
CONNECT 115200 EC*  
DELAYED  
10  
11  
12  
13  
14  
24  
25  
86  
40  
55  
56  
57  
58  
59  
60  
28  
18  
87  
88  
89  
90  
70  
71  
72  
Connection at 2400 bits/s.  
Connection at 4800 bits/s.  
Connection at 9600 bits/s.  
Connection at 14400 bits/s.  
Connection at 19200 bits/s.  
Connection at 7200 bits/s.  
Connection at 12000 bits/s.  
Connection at 16800 bits/s.  
Connection at 300 bits/s.  
Connection at 21600 bits/s.  
Connection at 24000 bits/s.  
Connection at 26400 bits/s.  
Connection at 28800 bits/s.  
Connection at 31200 bits/s.  
Connection at 33600 bits/s.  
Connection at 38400 bits/s. (DTE rate)  
Connection at 57600 bits/s. (DTE rate)  
Connection at 115200 bits/s. (DTE rate)  
Delay is in effect for the dialed number.  
Dialed number is blacklisted.  
Blacklist is full.  
BLACKLISTED  
BLACKLIST FULL  
CONNECT 32000 EC*  
CONNECT 34000 EC*  
CONNECT 03600 EC*  
Connection at 32000 bits/s. (K56flex or V.90 mode)  
Connection at 34000 bits/s. (K56flex mode)  
Connection at 36000 bits/s. (K56flex or V.90 mode)  
Result Codes Summary  
90  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Result Code  
Numeric  
Description  
CONNECT 38000 EC*  
CONNECT 40000 EC*  
CONNECT 42000 EC*  
CONNECT 44000 EC*  
CONNECT 46000 EC*  
CONNECT 48000 EC*  
CONNECT 50000 EC*  
CONNECT 52000 EC*  
CONNECT 54000 EC*  
CONNECT 56000 EC*  
CONNECT 28000 EC*  
CONNECT 29333 EC*  
CONNECT 30666 EC*  
CONNECT 33333 EC*  
CONNECT 34666 EC*  
CONNECT 37333 EC*  
CONNECT 38666 EC*  
CONNECT 41333 EC*  
CONNECT 42666 EC*  
CONNECT 45333 EC*  
CONNECT 46666 EC*  
CONNECT 49333 EC*  
CONNECT 50666 EC*  
CONNECT 53333 EC*  
CONNECT 54666 EC*  
73  
74  
Connection at 38000 bits/s. (K56flex mode)  
Connection at 40000 bits/s. (K56flex or V.90 mode)  
Connection at 42000 bits/s. (K56flex mode)  
Connection at 44000 bits/s. (K56flex or V.90 mode)  
Connection at 46000 bits/s. (K56flex mode)  
Connection at 48000 bits/s. (K56flex or V.90 mode)  
Connection at 50000 bits/s. (K56flex mode)  
Connection at 52000 bits/s. (K56flex or V.90 mode)  
Connection at 54000 bits/s. (K56flex mode)  
Connection at 56000 bits/s. (K56flex mode)  
Connection at 28000 bits/s. (V.90 mode)  
Connection at 29333 bits/s. (V.90 mode)  
Connection at 30666 bits/s. (V.90 mode)  
Connection at 33333 bits/s. (V.90 mode)  
Connection at 34666 bits/s. (V.90 mode)  
Connection at 37333 bits/s. (V.90 mode)  
Connection at 38666 bits/s. (V.90 mode)  
Connection at 41333 bits/s. (V.90 mode)  
Connection at 42666 bits/s. (V.90 mode)  
Connection at 45333 bits/s. (V.90 mode)  
Connection at 46666 bits/s. (V.90 mode)  
Connection at 49333 bits/s. (V.90 mode)  
Connection at 50666 bits/s. (V.90 mode)  
Connection at 53333 bits/s. (V.90 mode)  
Connection at 54666 bits/s. (V.90 mode)  
75  
76  
77  
78  
79  
80  
81  
82  
100  
101  
102  
103  
104  
105  
106  
107  
108  
109  
110  
111  
112  
113  
114  
* EC only appears when the extended result code configuration option is enabled. EC is replaced by one of the  
following symbols, depending upon the error control method used:  
V42bis -> V.42 error control and V.42bis data compression.  
V42 -> V.42 error control only.  
MNP5 -> MNP class 4 error control and MNP class 5 data compression.  
MNP4 -> MNP class 4 error control only.  
Neck -> No error control protocol.  
Note: In “Normal mode”, connection speed is up to 31200bps.  
Result Codes Summary  
91  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Appendix C  
Agency Notices  
FCC Notices  
9
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant  
to Part 15 of the FCC rules. Changes or modifications not expressly approved by Fujitsu PC Corporation  
could void the user’s authority to operate the equipment.  
Notice to Users of Radios and Television  
9
These limits are designed to provide reasonable protection against harmful interference in a residential  
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed  
and used in accordance with the instructions, may cause harmful interference to radio communications.  
However, there is no guarantee that interference will not occur in a particular installation. If the  
equipment does cause harmful interference to radio or television reception, which can be determined by  
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more  
of the following measures:  
• Reorient or relocate the receiving antenna.  
• Increase the separation between the equipment and receiver.  
• Connect the equipment into an outlet that is on a different circuit than the receiver.  
• Consult the dealer or an experienced radio/ TV technician for help.  
Shielded interconnect cables must be employed with this equipment to ensure compliance with the  
pertinent RF emissions limits governing this device.  
Notice to Users of the US Telephone Network  
9
Note: Stylistic 3500 pen tablets shipped outside of North America do not have an internal modem. The  
following information applies only to those systems with an internal modem.  
The Stylistic 3500 pen tablet is supplied with an internal modem which complies with Part 68 of the FCC  
rules. On the pen tablet is a label that contains the FCC Registration Number and Ringer Equivalence  
Number (REN) of this system, along with other information. If requested, users must provide their  
telephone company with the following information:  
• The telephone number to which the pen tablet is connected  
• The Ringer Equivalence Number (REN) for this equipment  
• The information that the system requires a standard modular jack type USOC RJ-11C which is FCC  
Part 68-compliant  
• The FCC Registration Number  
This equipment is designed to be connected to the telephone network or premises wiring using a  
standard modular jack type USOC RJ-11C which is FCC Part 68-compliant.  
The REN is used to determine the number of devices you may connect to your telephone line and still  
have all those devices ring when your number is called.Too many devices on one line may result in  
92  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
failure to ring in response to an incoming call. In most, but not all, areas, the sum of all of the devices  
should not exceed five (5). To be certain of the number of devices you may connect to your line, as  
determined by the RENs, contact your local telephone company.  
If this equipment causes harm to the telephone network, your telephone company may discontinue your  
service temporarily. If possible, they will notify you in advance. If advance notice is not practical, they  
will notify you as soon as possible. You will also be advised of your right to file a complaint with the  
FCC.  
This fax modem also complies with fax branding requirements per FCC Part 68.  
If you experience trouble with this equipment, please contact your support representative.  
Your telephone company will probably ask you to disconnect this equipment from the telephone network  
until the problem is corrected and you are sure that the equipment is not malfunctioning.  
This equipment may not be used on coin service telephones provided by your telephone company.  
Connection to party lines is subject to state tariffs. Contact your state’s public utility commission, public  
services commission, or corporation commission for more information.  
FCC rules prohibit the use of non-hearing aid compatible telephones in the following locations or  
applications:  
• All public or semipublic coin-operated or credit card telephones.  
• Elevators, highways, tunnels, (automobile, subway, railroad, or pedestrian) where a person with  
impaired hearing might be isolated in an emergency.  
• Places where telephones are specifically installed to alert emergency authorities such as fire, police, or  
medical assistance personnel.  
• Hospital rooms, residential health care facilities, convalescent homes, and prisons.  
• Workstations for the hearing impaired.  
• Hotel, motel, or apartment lobbies.  
• Stores where telephones are used by patrons to order merchandise.  
• Public transportation terminals where telephones are used to call taxis or to reserve lodging or rental  
cars.  
• In hotel and motel rooms at least ten percent of the rooms must contain hearing aid compatible  
telephones which will be provided to hearing impaired customers on request.  
DOC (Industry Canada) Compliance Notices  
9
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus  
as set forth in the radio interference regulations of the Canadian Department of Communications.  
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux  
appareils numériques de classe B prescrites dans le règlement sur le brouillage radioélectrique édicté par  
le Ministère des Communications du Canada.  
Notice to Users of Radios and Television  
9
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment  
regulations.  
Cet appareil numérique de la classe B respecte toutes les exigences du règlement sur le matériel  
brouilleur du Canada.  
DOC (Industry Canada) Compliance Notices  
93  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Notice to Users of the Canadian Telephone Network  
9
The Canadian Industry Canada label identifies certified equipment. This certification means that the  
equipment meets certain telecommunications network protective, operational, and safety requirements.  
The Department does not guarantee the equipment will operate to the user’s satisfaction.  
Repairs to telecommunication equipment should be made by a Canadian authorized maintenance facility.  
Any repairs or alterations not expressly approved by Fujitsu PC Corporation or any equipment failures  
may give the telecommunications company cause to request the user to disconnect the equipment from  
the telephone line.  
The connecting arrangement code for this equipment is CA11A.  
The Load Number assigned to each telephone terminal device denotes the percentage of the total load to  
be connected to a telephone loop or circuit to be used by the device to prevent overloading. The  
termination on a loop may consist of any combination of devices such that the total of the load numbers  
of all devices does not exceed 100.  
Caution  
For safety, users should ensure that the electrical ground of the  
power utility, the telephone lines, and the metallic water pipes are  
connected together. Users should not attempt to make such  
connections themselves but should contact the appropriate electric  
inspection authority or electrician. This may be particularly  
important in rural areas.  
Avis Aux Utilisateurs Du Réseau Téléphonique Canadien  
9
L’étiquette canadienne Industrie Canada identifie l’équipement certifié. Cette certification signifie que  
l’équipement satisfait certaines normes de protection, d’exploitation et de sécurité des réseaux de  
télécommunications. Le département ne garantit pas le fonctionnement de l’équipement à la satisfaction  
de l’utilisateur.  
Le Stylistic 3500 possede un modem interne conforme aux normes de certification d’Industrie Canada  
pour protéger les réseaux de télécommunications et satisfaire aux normes de sécurité. Avant de connecter  
cet équipement à une ligne téléphonique, l’utilisateur doit vérifier s’il est permis de connecter cet  
équipement aux installations de télécommunications locales. L’utilisateur est averti que même la  
conformité aux normes de certification ne peut dans certains cas empêcher la dégradation du service.  
Les réparations de l’équipement de télécommunications doivent être effectuées par un service de  
maintenance agréé au Canada. Toute réparation ou modification, qui n’est pas expressement approuvée  
par Fujitsu PC Corporation, ou toute défaillance de l’équipement peut entrainer la compagnie de  
télécommunications à exiger que l’utlilisateur déconnecte l‘équipement de la ligne téléphonique.  
Le code d’arrangement de connexion de cet équipement est CA11A.  
Le numéro de charge assigné à chaque terminal téléphonique indique le pourcentage de la charge totale  
pouvant être connecté à une boucle ou à un circuit téléphonique, utilisé par ce périphérique afin de  
prévenir toute surcharge. La terminaison d’une boucle peut être constituée de n’importe quelle  
combinaison de périphériques de sorte que le total de numéros de charge de tous les périphériques  
n’excède pas 100.  
DOC (Industry Canada) Compliance Notices  
94  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Avertissement  
Pour assurer la sécurité, les utilisateurs doivent vérifier que la prise  
de terre du service d’électricité, les lignes téléphoniques et les  
conduites d’eau métalliques sont connectées ensemble. Les  
utilisateurs NE doivent PAS tenter d’établir ces connexions  
eux-mêmes, mais doivent contacter les services d’inspection  
d’installations électriques appropriés ou un électricien. Ceci peut  
être particulièrement important en régions rurales.  
DOC (Industry Canada) Compliance Notices  
95  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Index  
Security menu options, 18, 20  
serial port A, enabling, 11  
serial port B, device, selecting, 11  
setup prompt, enabling, 24  
A
AC adapter, specifications, 42  
ACPI, support for, 1  
agency approval, specifications, 43  
agency compliance, 43  
starting, 5  
supervisor password, enabling, 18  
suspend mode timeout, selecting, 22  
suspend mode, selecting, 22  
suspend/resume button, normal, resume only, power on/  
off, configuration, 23  
system date, changing, 8  
system time, changing, 8  
using, 6  
agency notices, 92  
Air Bubbles in Display, 40  
APIs for configuring BIOS options, 68  
BIOSSetupSet, 69  
Error Codes, 70  
InitializeBIOS, 69  
Option and Setting parameters, 70  
ReadBIOSSettings, 69  
summary of functions, 68  
BIOS version, displaying in BIOS Setup, 25  
boot sequence, selecting in BIOS Setup, 24  
boot-time diagnostic messages, enabling in BIOS Setup, 24  
bridge battery, 42  
UpdateBIOSCheckSum, 69  
APM Power Savings, BIOS option, 21  
audio inputs and outputs, enabled and disabled on pen tablet  
and port replicator, 59  
audio jacks, connector, specifications, 41  
C
cache, specifications, 38  
cache, viewing size of in BIOS Setup, 25  
calibration, pen, 4  
CIC PenX 1.7 with CIC HRS 5.0.5, 2  
configuration tools and utilities, overview, 2  
connectors  
DC power input, pin assignments, 48  
floppy disk drive port, pin assignments, 49  
high-usage contacts, position assignments, 47  
serial port, pin assignments, 48  
system interface port, pin assignments, 52  
CPU speed, specifications, 38  
B
battery  
battery pack, battery life, 42  
battery pack, charge status, 66  
battery pack, system power hardware and power  
management, 66  
bridge battery, specifications, 42  
main battery pack, specifications, 42  
sub battery, 42  
BIOS configuration APIs, 68  
BIOS settings  
CPU speed, viewing in BIOS Setup, 25  
current BIOS settings, 4  
about, 4  
BIOS Setup  
Boot menu options, 24  
boot sequence, selecting, 24  
boot-time diagnostic messages, enabling, 24  
display screen, 6  
Exit menu options, 25  
floppy disk drive, enabling, 8  
hotpads, enabling, 10  
IDE Hard Disk Drive submenu, 9  
Info menu, 25  
IR mode, selecting, 11  
level 2 cache, enabling, 8  
Main menu options, 8  
parallel port mode, selecting, 12  
parallel port, enabling, 12  
Plug and Play OS, enabling, 10  
Power Savings menu, 21  
QuickBoot mode, enabling, 24  
resume on modem ring, enabling, 22  
resume on serial activity, enabling, 23  
resume on time, enabling, 22  
D
date, changing in BIOS Setup, 8  
DC power input, 48  
connector, pin assignments, 48  
connector, specifications, 67  
voltage specifications, 41  
default settings for BIOS Setup options, 25  
digitizer, specifications, 40  
dimensions, pen tablet, 43  
DIMM card, removing, 37  
DIMM slot, specifications, 38  
display select hotpad and display BIOS option, 14  
display, external, selecting in BIOS Setup, 14  
display, specifications, indoor and outdoor displays, 39  
DLLs for configuring BIOS options, See also APIs for  
configuring BIOS options, 68  
DLLs for configuring BIOS options, version information, 68  
DMI event logging options, BIOS Setup, 17  
Index-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
E
L
ECP mode, parallel port, selecting, 12  
emulate mouse, pen subsystem, 4  
environmental, specifications, 43  
exiting BIOS Setup, exit menu options, 25  
external video, 39  
level 1 cache, viewing size of in BIOS Setup, 25  
level 2 cache, enabling in BIOS Setup, 8  
level 2 cache, viewing size of in BIOS Setup, 25  
M
memory  
F
DIMM slot, specifications, 38  
video memory, specifications, 38  
viewing size of in BIOS Setup, 25  
microphone, disabled when external microphone used, 59  
Microsoft Developer’s Network, ix  
Microsoft Pen Services 2.0 with CIC HRS 5.0.5, 2  
mini-dock  
floppy disk drive  
enabling in BIOS Setup, 8  
port, connector specifications, 41  
port, pin assignments, 49  
H
specifications, 46  
modem, internal, See also internal modem, 1  
mouse emulation, pen subsystem, 2  
Handwriter Settings control panel, overview, 3  
Handwriter Tutorial for Pen X, selecting the correct subsystem  
for, 4  
Handwriting Trainer for pen Windows, selecting the correct  
subsystem for, 4  
O
hard disk drive  
operating systems, supported, 2  
organization of this manual, viii  
configuration method, selecting in BIOS Setup, 9  
installing, 78  
internal, replacing, 75  
removing, 75  
P
specifications, 41  
parallel port  
spin-down timeout, configuring in BIOS Setup, 21  
hard disk drive port, specifications, 64  
hardware options, installing, 35  
headphone jack, 60  
enabling in BIOS Setup, 12  
mode, selecting in BIOS Setup, 12  
password on boot, BIOS option, 18  
passwords, in BIOS Setup, 18  
PC 99 design guidelines, 1  
PC Card  
heat  
system, and power management, 21  
high-usage contacts  
PC Card Standards, related documentation, ix  
slots, specifications, 41  
support, 1–2  
position assignments, 47  
specifications, 41  
hotpad notification, 73  
hotpads, enabling in BIOS Setup, 10  
humidity, specifications, 43  
PC Card port, specifications, 61  
PC Card support, for Windows 98 and Windows 2000, 2  
PC Card supported standard, release 3.0, 2  
PC Cards, installing, 35  
PC Cards, removing, 36  
PCIC protocol, 1  
I
I/O controller, specifications, 38  
info menu, in BIOS Setup, 25  
installing PC Cards, 35  
pen buttons, configuring, 4  
Pen Configuration control panel  
capabilities, 4  
installing the hard disk drive, 78  
installing the internal hard disk drive, 75  
internal LAN/modem  
specifications, 44  
internal modem, 1  
IR mode, selecting in BIOS Setup, 11  
IrDA port, specifications, 41, 59  
IrDA standards, ix  
overview, 3  
pen digitizer, specifications, 40  
pen subsystem, selecting, 4  
pen subsystems, supported, 4  
pen support, selectable subsystems, 2  
pen tablet features, 1  
Pen Windows, subsystem supported, 4  
Pen X, subsystem supported, 4  
pen, calibration, 4  
IRQ Reservation submenu, BIOS Setup, 16  
pen, sampling rate, 4  
peripheral interface, specifications, 41  
peripheral interfaces, on pen tablet, 47  
permanent BIOS settings, 4  
PHDISK  
K
KillHotpadNotification function, 74  
command line options, 27  
Index-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
create option, 28  
create option syntax, 30  
delete option, 31  
environmental, 43  
hard disk drive port, 64  
high-usage contacts, 41  
humidity, 43  
errors, 32–34  
file option, 29  
I/O controller, 38  
hard disk preparation utility, 27  
help screen, 32  
infrared keyboard port, 41  
interfaces, 46  
info option, 31  
IrDA port, 41, 59  
messages, 32  
logic system, 38  
partition and file size, 29  
partition option, 29  
reformat option, 30  
memory, 38  
PC Card controller, 38  
PC Card port, 61  
utility, overview, 3  
physical, 43  
physical specifications, 43  
Plug and Play OS, enabling in BIOS Setup, 10  
port replicator, specifications, 46  
power management  
port replicator/mini-dock, 46  
power management, APM revision level 1.2 supported, 42  
power system, 42  
processor, 38  
ACPI revision 1.0 supported, 42  
APM revision 1.2 supported, 42  
power management microcontroller unit (PMU), 66  
power system, specifications, 42  
states, 66  
serial port, 41  
sub battery, 42  
temperature, 43  
USB port, 41  
video controller, 38  
video memory, 38  
power savings, BIOS Setup options, 21  
programmable hotpad, libraries for programming, 73  
sub battery, 42  
supervisor password, diskette access, supervisor only, 19  
supervisor password, enabling in BIOS Setup, 18  
suspend mode timeout, selecting in BIOS Setup, 22  
suspend mode, selecting in BIOS Setup, 22  
suspend/resume button, normal, resume only, power on/off,  
configuration, 23  
Q
QuickBoot mode, enabling in BIOS Setup, 24  
suspend-to-disk after 1 hour in suspend-to-RAM mode, 22  
SVGA video mode, 39  
system date, changing in BIOS Setup, 8  
system interface port  
connector type, 41  
system power, 66  
R
related documentation, ix  
removing a DIMM card, 37  
removing the hard disk drive, 75  
resume on modem ring, enabling in BIOS Setup, 22  
resume on serial activity, enabling in BIOS Setup, 23  
resume on time, enabling in BIOS Setup, 22  
resume time, setting in BIOS, 22  
system time, changing in BIOS Setup, 8  
T
technical support, x  
S
temperature, specifications, 43  
TFT color display, specifications, 39  
time, changing in BIOS Setup, 8  
sampling rate, pen, 4  
save-to-disk, partition and file size, 29  
serial port A, enabling in BIOS Setup, 11  
serial port B device, selecting in BIOS Setup, 11  
serial port, connector, pin assignments, 48  
serial port, specifications, 41  
SetHotpadNotification function, 74  
setup prompt, enabling in BIOS setup, 24  
speaker, disabled when headphone jack used, 60  
Specifications, 38  
U
Universal Serial Bus, specification, ix  
USB port, position assignments, 50  
USB port, specifications, pen tablet, 41  
USB port, specifications, port replicator, 46  
user password, enabling in BIOS Setup, 18  
specifications  
AC adapter, 42  
agency approvals, 43  
audio controller, 38  
V
battery pack, 42  
cache, 38  
DC power input connector, 67  
DC power input voltage, 41  
digitizer, 40  
video controller, specifications, 38  
video memory, specifications, 38  
video modes supported for use with external monitor, 39  
video, external, 39  
DIMM slot, 38  
Index-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
W
weight, pen tablet, 43  
Windows 2000  
ACPI and BIOS settings, 21  
version preinstalled, 2  
Windows 98  
ACPI and BIOS settings, 21  
support, 2  
Windows NT  
PC Card support, 2  
version preinstalled, (Workstation 4.0), 2  
X
XVGA video mode, 39  
Index-4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3/01  
FPC58-0473-01  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Electro Voice Portable Speaker 15TRX User Manual
Fender Guitar 011 7602 User Manual
Fisher Price Motorized Toy Car 75548 User Manual
FMI Indoor Fireplace DVF36NH HA User Manual
Frigidaire Ice Maker IM115 User Manual
Furuno Telephone FS 1503 User Manual
GE Automobile Electronics design line 5 button key fob User Manual
GE Monogram Dishwasher EDW5000 User Manual
Generac Portable Generator 005518 1 User Manual
Go Go Babyz Baby Accessories UA105 User Manual