Frymaster, a member of the Commercial Food Equipment Service Association, recommends
using CFESA Certified Technicians.
SEPTEMBER 2005
24-Hour Service Hotline 1-800-551-8633
* 8 1 9 5 9 9 1 *
Download from Www.Somanuals.com. All Manuals Search And Download.
DANGER
No structural material on the fryer should be altered or removed to accommodate placement of
the fryer under a hood. Questions? Call the Frymaster Dean Service Hotline at 1-800-551-8633.
DANGER
Adequate means must be provided to limit the movement of this appliance without depending
upon the gas line connection. Single fryers equipped with legs must be stabilized by installing
anchor straps. All fryers equipped with casters must be stabilized by installing restraining
chains. If a flexible gas line is used, an additional restraining cable must be connected at all
times when the fryer is in use.
DANGER
The front ledge of the fryer is not a step! Do not stand on the fryer. Serious injury can result
from slips or contact with the hot oil.
DANGER
Do not store or use gasoline or other flammable liquids or vapors in the vicinity of this or any
other appliance.
DANGER
Instructions to be followed in the event the operator smells gas or otherwise detects a gas leak
must be posted in a prominent location. This information can be obtained from the local gas
company or gas supplier.
DANGER
This product contains chemicals known to the state of California to cause cancer and/or birth
defects or other reproductive harm.
Operation, installation, and servicing of this product could expose you to airborne particles of
glasswool or ceramic fibers, crystalline silica, and/or carbon monoxide. Inhalation of airborne
particles of glasswool or ceramic fibers is known to the State of California to cause cancer.
Inhalation of carbon monoxide is known to the State of California to cause birth defects or other
reproductive harm.
DANGER
The crumb tray in fryers equipped with a filter system must be emptied into a fireproof container
at the end of frying operations each day. Some food particles can spontaneously combust if left
soaking in certain shortening material.
WARNING
Do not bang fry baskets or other utensils on the fryer’s joiner strip. The strip is present to seal
the joint between the fry vessels. Banging fry baskets on the strip to dislodge shortening will
distort the strip, adversely affecting its fit. It is designed for a tight fit and should only be
removed for cleaning.
NOTICE
The Commonwealth of Massachusetts requires any and all gas products to be installed by a
licensed plumber or pipe fitter.
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
PRO H55 SERIES GAS FRYER
INSTALLATION & OPERATION MANUAL
TABLE OF CONTENTS
CHAPTER 1: General Information
1.1 Applicability and Validity................................................................................................. 1-1
1.2 Parts Ordering and Service Information............................................................................ 1-1
1.3 Safety Information............................................................................................................. 1-2
1.4 European Community (CE) Specific Information............................................................. 1-2
1.5 Equipment Description...................................................................................................... 1-3
1.6 Installation, Operating, and Service Personnel ................................................................. 1-3
1.7 Definitions......................................................................................................................... 1-3
1.8 Shipping Damage Claim Procedure .................................................................................. 1-4
CHAPTER 2: Installation Instructions
2.1 General Installation Requirements .................................................................................... 2-1
2.2 Caster/Leg Installation ...................................................................................................... 2-3
2.3 Pre-Connection Preparations............................................................................................. 2-3
2.4 Connection to Gas Line..................................................................................................... 2-5
2.5 Converting to Another Gas Type ...................................................................................... 2-8
CHAPTER 3: Operating Instructions
3.1 Controller Operation and Programming............................................................................ 3-1
3.2 Start-Up Procedure............................................................................................................ 3-1
3.3 Boiling Out the Frypot ...................................................................................................... 3-3
3.4 Shutting the Fryer Down ................................................................................................... 3-3
CHAPTER 4: Filtration Instructions
4.1 Draining and Manual Filtering.......................................................................................... 4-1
4.2 Preparing the Built-In Filtration System for Use .............................................................. 4-2
4.3 Operation of the Filter ....................................................................................................... 4-5
4.4 Disassembly and Reassembly of the Magnasol Filter....................................................... 4-8
4.5 Draining and Disposing of Waste Oil ............................................................................... 4-9
4.6 Using the Optional Rear-Discharge Oil Disposal ........................................................... 4-10
CHAPTER 5: Preventive Maintenance
5.1 Fryer Preventive Maintenance Checks and Service.......................................................... 5-1
Daily Checks and Service.................................................................................................. 5-1
Weekly Checks and Service.............................................................................................. 5-1
Monthly Checks and Service............................................................................................. 5-3
Quarterly Checks and Service ........................................................................................... 5-4
Semi-Annual Checks and Service ..................................................................................... 5-6
5.2 Built-In Filtration System Preventive Maintenance Checks and Service ......................... 5-6
5.3 Annual/Periodic System Inspection .................................................................................. 5-7
CHAPTER 6: Operator Troubleshooting
6.1 Introduction ....................................................................................................................... 6-1
6.2 Troubleshooting Fryers with Computer Magic III.5, Basket Lift Timer, or Digital
Controller........................................................................................................................... 6-2
6.3 Troubleshooting Fryers with Solid State (Analog) Controller.......................................... 6-4
6.4 Troubleshooting the Built-In Filtration System ................................................................ 6-6
6.5 Troubleshooting the Basket Lift........................................................................................ 6-8
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
THIS PAGE INTENTIONALLY LEFT BLANK
Download from Www.Somanuals.com. All Manuals Search And Download.
PRO H55 SERIES GAS FRYER
CHAPTER 1: GENERAL INFORMATION
1.1
Applicability and Validity
The Pro H55 Series Gas Fryer has been approved by the European Union for sale and installa-
tion in the following EU countries: AT, BE, DE, DK, ES, FI, FR, GB, IE, IT, LU, NL, NO, PT
and SE.
This manual is applicable to and valid for all Pro H55 Series Gas Fryers sold in English-
speaking countries, including those in the European Union. Where conflicts exist between in-
structions and information in this manual and local or national codes of the country in which
the equipment is installed, installation and operation shall comply with those codes.
This appliance is only for professional use and shall be used by qualified personnel only, as
defined in Section 1.7.
1.2
Parts Ordering and Service Information
In order to assist you quickly, the Frymaster Factory Authorized Service Center (FASC) or Service
Department representative requires certain information about your equipment. Most of this
information is printed on a data plate affixed to the inside of the fryer door. Part numbers are found
in the Installation, Operation, Service, and Parts Manual. Parts orders may be placed directly with
your local FASC or distributor. Included with fryers when shipped from the factory is a list of
Frymaster FASCs. If you do not have access to this list, contact the Frymaster Service Department
at 1-800-551-8633 or 1-318-865-1711 or by e-mail: [email protected].
When ordering parts, the following information is required:
Model Number:
Serial Number:
Type of Gas or Voltage:
Item Part Number:
Quantity Needed:
Service information may be obtained by contacting your local FASC/Distributor. Service may also
be obtained by calling the Frymaster Service Department at 1-800-551-8633 or 1-318-865-1711 or
ready:
Model Number:
Serial Number:
Type of Gas:
In addition to the model number, serial number, and type of gas, please be prepared to describe the
nature of the problem and have ready any other information that you think may be helpful in solving
your problem.
RETAIN AND STORE THIS MANUAL IN A SAFE PLACE FOR FUTURE USE.
1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
1.3
Safety Information
Before attempting to operate your unit, read the instructions in this manual thoroughly. Throughout
this manual, you will find notations enclosed in double-bordered boxes similar to the ones that
follow.
CAUTION
CAUTION boxes contain information about actions or conditions that may cause or result
in a malfunction of your system.
WARNING
WARNING boxes contain information about actions or conditions that may cause or result
in damage to your system, and which may cause your system to malfunction.
DANGER
DANGER boxes contain information about actions or conditions that may cause or result
in injury to personnel, and which may cause damage to your system and/or cause your
system to malfunction.
Your fryer is equipped with automatic safety features:
1. High temperature detection shuts off gas to the burner assembly should the controlling
thermostat fail.
2. An optional safety switch built into the drain valve prevents burner ignition with the drain valve
even partially open.
1.4
European Community (CE) Specific Information
The European Community (CE) has established certain specific standards regarding equipment of
this type. Whenever a conflict exists between CE and non-CE standards, the information or
instructions concerned are identified by means of shadowed boxes similar to the one below.
Non-CE Standard
for Incoming Gas Pressures
Type
Minimum Maximum
6" W.C.
14" W.C.
3.49 kPa
Natural
1.49 kPa
14.68 mbar 34.72 mbar
11" W.C.
2.74 kPa
14" W.C.
3.49 kPa
LP
27.28 mbar 34.84 mbar
1-2
Download from Www.Somanuals.com. All Manuals Search And Download.
1.5
Equipment Description
Pro H55 Series high-efficiency gas fryers employ a unique infrared burner system that uses up to
43% less energy to cook the same volume as conventional open-burner fryers. Models in this series
include PH55, FMPH55, and FPPH55 variants. PH55 models have no built-in filtration system.
FPPH55 models have a built-in FootPrint Pro filtration system located under the leftmost two fryers
in a battery. FMPH55 models also have a built-in FootPrint Pro filtration system under the leftmost
two stations of a battery. The difference between FPPH55s and FMPH55s is that FPPH55s have no
holding stations (i.e., the battery consists only of fryers) while the FMPH55s have a holding station
at one of the positions in the battery. For example, an FPPH355 consists of three fryers with built-in
filtration; an FMH355, by comparison, consists of two fryers and one holding station with built-in
filtration. A PH355 consists of three fryers without built-in filtration.
All Pro H55 Series Gas fryers are of an open-frypot design with no tubes and have a hand-sized
opening into the deep cold zone, which makes cleaning the stainless frypot quick and easy.
Heating is supplied by a pair of infrared burner assemblies mounted on each side of the frypot.
Combustion air for the burners is supplied by a dedicated blower mounted on the front of the frypot.
Pro H55 Series Gas fryers can be configured for natural gas, propane (LP), or manufactured gas, as
required by the customer.
Each frypot is equipped with a temperature probe for precise temperature control.
All Pro H55 Series Gas fryers come standard with electronic ignition, melt cycle and boil-out mode.
Control options include Computer Magic III.5 computers, solid-state (analog) controllers, digital
controllers, and basket lift timers.
All fryers in this series require an external source of AC electrical power. Units can be configured
for voltages ranging from 100 VAC to 240 VAC.
FMPH55 and FPPH55 fryers are shipped completely assembled. PH55 fryers may require
installation of legs or optional casters at the point of use. All fryers are shipped with a package of
standard accessories. Each fryer is adjusted, tested, and inspected at the factory before crating for
shipment.
1.6
Installation, Operating, and Service Personnel
Operating information for Frymaster equipment has been prepared for use by qualified and/or
authorized personnel only, as defined in Section 1.7. All installation and service on Frymaster
equipment must be performed by qualified, certified, licensed, and/or authorized installation
or service personnel, as defined in Section 1.7.
1.7
Definitions
QUALIFIED AND/OR AUTHORIZED OPERATING PERSONNEL
Qualified/authorized operating personnel are those who have carefully read the information in this
manual and have familiarized themselves with the equipment functions, or who have had previous
experience with the operation of the equipment covered in this manual.
1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
QUALIFIED INSTALLATION PERSONNEL
Qualified installation personnel are individuals, firms, corporations, and/or companies which, either
in person or through a representative, are engaged in and are responsible for the installation of gas-
fired appliances. Qualified personnel must be experienced in such work, be familiar with all gas
precautions involved, and have complied with all requirements of applicable national and local
codes.
QUALIFIED SERVICE PERSONNEL
Qualified service personnel are those who are familiar with Frymaster equipment and who have been
authorized by Frymaster, L.L.C. to perform service on the equipment. All authorized service
personnel are required to be equipped with a complete set of service and parts manuals, and to stock
a minimum amount of parts for Frymaster equipment. A list of Frymaster Factory Authorized
Service Centers (FASC) is included with the fryer when shipped from the factory. Failure to use
qualified service personnel will void the Frymaster warranty on your equipment.
1.8
Shipping Damage Claim Procedure
Your Frymaster equipment was carefully inspected and packed before leaving the factory. The
transportation company assumes full responsibility for safe delivery upon its acceptance of the
equipment for transport.
What to do if your equipment arrives damaged:
1. File a claim for damages immediately, regardless of the extent of damages.
2. Inspect for and record all visible loss or damage, and ensure that this information is noted on
the freight bill or express receipt and is signed by the person making the delivery.
3. Concealed loss or damage that was unnoticed until the equipment was unpacked should be
recorded and reported to the freight company or carrier immediately upon discovery. A
concealed damage claim must be submitted within 15 days of the date of delivery. Ensure that
the shipping container is retained for inspection.
Frymaster DOES NOT ASSUME RESPONSIBILITY FOR DAMAGE OR LOSS
INCURRED IN TRANSIT.
1-4
Download from Www.Somanuals.com. All Manuals Search And Download.
PRO H55 SERIES GAS FRYER
CHAPTER 2: INSTALLATION INSTRUCTIONS
2.1
General Installation Requirements
Qualified, licensed, and/or authorized installation or service personnel, as defined in Section
1.7 of this manual, should perform all installation and service on Frymaster equipment.
Conversion of this appliance from one type of gas to another should only be performed by
qualified, licensed, and/or authorized installation or service personnel as defined in Section 1.7
of this manual.
Failure to use qualified, licensed, and/or authorized installation or service personnel (as de-
fined in Section 1.7 of this manual) to install, convert to another gas type or otherwise service
this equipment will void the Frymaster warranty and may result in damage to the equipment
or injury to personnel.
Where conflicts exist between instructions and information in this manual and local or na-
tional codes or regulations, installation and operation shall comply with the codes or regula-
tions in force in the country in which the equipment is installed.
DANGER
Building codes prohibit a fryer with its open tank of hot oil being installed beside an
open flame of any type, including those of broilers and ranges.
Upon arrival, inspect the fryer carefully for visible or concealed damage. (See Shipping Damage
Claim Procedure in Chapter 1.)
DANGER
Frymaster appliances equipped with legs are for stationary installations. Appliances
fitted with legs must be lifted during movement to avoid damage to the appliance
and bodily injury. For movable installations, optional equipment casters must be
used. Questions? Call 1-800-551-8633.
CLEARANCE AND VENTILATION
The fryer(s) must be installed with a 6” (150 mm) clearance at both sides and back when installed
adjacent to combustible construction; no clearance is required when installed adjacent to
noncombustible construction. A minimum of 24” (600 mm) clearance should be provided at the
front of the fryer.
DANGER
No structural material on the fryer should be altered or removed to accommodate
placement of the fryer under a hood. Questions? Call the Frymaster Dean Service
Hotline at 1-800-551-8633.
2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
One of the most important considerations of efficient fryer operation is ventilation. Make sure the
fryer is installed so that products of combustion are removed efficiently, and that the kitchen
ventilation system does not produce drafts that interfere with burner operation.
The fryer flue opening must not be placed close to the intake of the exhaust fan, and the fryer must
never have its flue extended in a “chimney” fashion. An extended flue will change the combustion
characteristics of the fryer, causing longer recovery time. It also frequently causes delayed ignition.
To provide the airflow necessary for good combustion and burner operation, the areas surrounding
the fryer front, sides, and rear must be kept clear and unobstructed.
DANGER
This appliance must be installed with sufficient ventilation to prevent the occurrence
of unacceptable concentrations of substances harmful to the health of personnel in
the room in which it is installed.
Fryers must be installed in an area with an adequate air supply and adequate ventilation. Adequate
distances must be maintained from the flue outlet of the fryer to the lower edge of the ventilation
filter bank. Filters should be installed at an angle of 45º. Place a drip tray beneath the lowest edge
of the filter. For U.S. installation, NFPA standard No. 96 states, “A minimum distance of 18 in.
(450 mm) should be maintained between the flue outlet and the lower edge of the grease filter.”
Frymaster recommends that the minimum distance be 24 in. (600 mm) from the flue outlet to the
bottom edge of the filter when the appliance consumes more than 120,000 BTU per hour.
For installations in the United States, information on construction and installation of ventilating
hoods can be found in the NFPA standard cited above. A copy of the standard may be obtained
from the National Fire Protection Association, Battery March Park, Quincy, MA 02269.
NATIONAL CODE REQUIREMENTS
The type of gas for which the fryer is equipped is stamped on the data plate attached to the inside of
the fryer door. Connect a fryer stamped “NAT” only to natural gas, those stamped “PRO” only to
propane gas, and those stamped “MFG” only to manufactured gas.
Installation shall be made with a gas connector that complies with national and local codes, and,
where applicable, CE codes. Quick-disconnect devices, if used, shall likewise comply with national,
local, and, if applicable, CE codes.
ELECTRICAL GROUNDING REQUIREMENTS
All electrically operated appliances must be grounded in accordance with all applicable national and
local codes, and, where applicable, CE codes. All units (cord connected or permanently connected)
should be connected to a grounded power supply system. A wiring diagram is located on the inside
of the fryer door. Refer to the rating plate on the inside of the fryer door for proper voltages.
DANGER
This appliance is equipped with a three-prong (grounding) plug for your protection
against electrical shock, and must be plugged directly into a properly grounded
three-prong receptacle. Do not cut, remove, or otherwise bypass the grounding
prong on this plug!
2-2
Download from Www.Somanuals.com. All Manuals Search And Download.
DANGER
This appliance requires electrical power for operation. Place the gas control valve in
the OFF position in case of a prolonged power outage. Do not attempt to operate
this appliance during a power outage.
AUSTRALIAN REQUIREMENTS
To be installed in accordance with AS 5601 / AG 601, local authority, gas, electricity, and any other
relevant statutory regulations.
FCC COMPLIANCE
The user is cautioned that any changes or modifications to Frymaster computers not expressly
approved by the party responsible for compliance could void the user’s authority to operate the
equipment.
Frymaster computers have been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC rules. While these devices are verified as Class A devices,
they have been shown to meet the Class B limits. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of the equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
The user may find the booklet “How to Identify and Resolve Radio-TV Interference Problems”
helpful. It is prepared by the Federal Communications Commission and is available from the U.S.
Government Printing Office, Washington, DC 20402, Stock No. 004-000-00345-4.
If necessary, the user should consult the dealer or an experienced radio and television technician for
additional suggestions.
2.2
Caster/Leg Installation
Depending upon the specific configuration ordered, your fryer may have been shipped without
installed casters or legs. DO NOT INSTALL THIS APPLIANCE WITHOUT CASTERS OR
LEGS. If the appliance requires the installation of casters or legs, install them in accordance
with the instructions included in your accessory package.
2.3
Pre-Connection Preparations
DANGER
DO NOT connect this appliance to the gas supply before completing each step in
this section.
After the fryer has been positioned under the exhaust hood, ensure the following has been
accomplished:
1. Adequate means must be provided to limit the movement of fryers without depending upon the
gas line connections. If a flexible gas hose is used, a restraining cable must be connected at all
times when the fryer is in use. The restraining cable and installation instructions are packed with
the flexible hose in the accessories box that was shipped with your unit.
2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Single unit fryers must be stabilized by installing restraining chains on fryers equipped with
casters or anchor straps on fryers equipped with legs. Follow the instructions in the accessory
pack to install the chains or straps.
DANGER
Do not attach an apron drainboard to a single fryer. The fryer may become unstable,
tip over, and cause injury. The appliance area must be kept free and clear of
combustible material at all times.
3. Level fryers equipped with legs by screwing out the legs approximately 1 inch then adjusting
them so that the fryer is level and at the proper height in the exhaust hood. Frymaster
recommends that the minimum distance from the flue outlet to the bottom edge of the hood be 24
in. (600 mm) when the appliance consumes more than 120,000 BTU per hour. NOTE: There
are no built-in leveling devices on fryers equipped with casters. The floor where the fryer is to
be installed must be level.
4. Test the fryer electrical system:
a. Plug the fryer electrical cord(s) into a grounded electrical receptacle.
b. Place the power switch in the ON position.
• For fryers equipped with solid-state (analog) controls, verify that the power and heat
lights are lit.
• For fryers having computer or digital displays, verify that the display indicates CYCL.
c. Place the fryer power switch in the OFF position. Verify that the power and heat lights are
out, or that the display is blank.
5. Refer to the data plate on the inside of the fryer door to determine if the fryer burner is
configured for the proper type of gas before connecting the fryer quick-disconnect device or
piping from the gas supply line.
6. Verify the minimum and maximum gas supply pressures for the type of gas to be used in
accordance with the accompanying tables.
CE Standard
CE Standard
for Incoming Gas Pressures
for Incoming Gas Pressures
for Fryers Manufactured After April 1999
for Fryers Manufactured Through April 1999
Orifice Diameter
Orifice Diameter
Regulator Pressure
Regulator Pressure
Pressure
(mbar)(1)
20
Pressure
(mbar)(1)
20
Single
Vat
Dual
Vat
Single
Vat
Dual
Vat
Single
Vat
Dual
Vat
Single
Vat
Dual
Vat
Gas
G20
G25
G30
G31
Gas
G20
G25
G30
G31
2 x 3.40 2 x 3.40 7 mbar
2 x 3.40 2 x 3.40 10 mbar
7 mbar
10 mbar
17 mbar
20 mbar
2 x 3.40 2 x 3.40 7 mbar
2 x 3.40 2 x 3.40 10 mbar
7 mbar
9 mbar
20 or 25
20 or 25
28/30 or 50 2 x 2.05 2 x 2.05 17 mbar
37 or 50 2 x 2.05 2 x 2.05 20 mbar
28/30 or 50 2 x 2.05 2 x 2.05 17 mbar 16,5 mbar
37 or 50 2 x 2.05 2 x 2.05 20,2 mbar 18,5 mbar
2
2
(1) mbar = 10,2 mm H O
(1) mbar = 10,2 mm H O
2-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Non-CE Standard
for Incoming Gas Pressures
Gas
Minimum
Maximum
6" W.C.
1.49 kPa
14" W.C.
3.48 kPa
Natural
14.93 mbar 34.84 mbar
11" W.C.
2.74 kPa
14" W.C.
3.48 kPa
LP
27.37 mbar 34.84 mbar
7. For fryers equipped with a FootPrint Pro system or basket lifts, plug the electrical cord(s) into a
power receptacle behind the fryer.
2.4
Connection to Gas Line
DANGER
Before connecting new pipe to this appliance, the pipe must be blown out thor-
oughly to remove all foreign material. Foreign material in the burner and gas con-
trols will cause improper and dangerous operation.
DANGER
When pressure-testing incoming gas supply lines, disconnect the fryer from the gas
line if the test pressure will be ½ PSIG (3.45 kPa, 13.84 inches W.C.) or greater to
avoid damage to the fryer’s gas tubes and gas valve(s).
DANGER
All connections must be sealed with a joint compound suitable for the gas being
used and all connections must be tested with a solution of soapy water before light-
ing any pilots.
Never use matches, candles, or any other ignition source to check for leaks. If gas
odors are detected, shut off the gas supply to the appliance at the main shut-off
valve and immediately contact the local gas company or an authorized service
agency for service.
DANGER
“Dry-firing” your unit will cause damage to the frypot and can cause a fire. Always
ensure that melted shortening, cooking oil, or water is in the frypot before firing the
unit.
The size of the gas line used for installation is very important. If the line is too small, the gas
pressure at the burner manifold will be low. This may cause slow recovery and delayed ignition.
The incoming gas supply line should be a minimum of 1½” (38 mm) in diameter. Refer to the chart
on the following page for the minimum sizes of connection piping.
2-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Gas Connection Pipe Sizes
(Minimum incoming pipe size should be 1 1/2" (41 mm))
4 or more
Gas
Natural
Single Unit
2 - 3 Units
1" (28 mm) 1 1/4" (36 mm)
1" (28 mm)
1" (28 mm) 1 1/4" (36 mm) 1 1/2" (41 mm)
units*
3/4" (22 mm)
Propane
1/2" (15 mm) 3/4" (22 mm)
Manufactured
* For distances of more than 20 feet (6 m) and/or more
than 4 fittings or elbows, increase the connection by one
pipe size.
The Pro H55 Series gas fryer has received the CE mark for the countries and gas categories
indicated in the table below. NOTE: The nominal heat input (QN) is 21kW except for AT, DE, LU
and category 3P/B, which is 23kW.
CE Approved Gas Categories by Country
COUNTRIES
CATEGORIES
GAS
G20
G30, G31
G20, G25
G30, G31
G20
G30, G31
G20, G25
G30, G31
G20, G25
G31
PRESSURE (MBAR)
20
50
20, 25
28-30, 37
20
AUSTRIA (AT)
II2H3B/P
I2E(R)B
I3+
BELGIUM (BE)
DENMARK (DK)
II2H3B/P
II2Esi3+
II2Esi3P
II2H3B/P
30
20, 25
28-30, 37
20, 25
50
FRANCE (FR)
G20
20
30
20
50
FINLAND (FI)
G30, G31
G20, G25
G30, G31
G31
II2ELL3B/P
I3P
GERMANY (DE)
50
G20
G30, G31
G20
G30, G31
G20
G30, G31
G20
G30, G31
G25
G31
20
28-30, 37
20
28-30, 37
20
28-30, 37
20
GREECE (GR)
ITALY (IT)
II2H3+
II2H3+
II2H3+
IRELAND (IE)
LUXEMBOURG (LU)
II2E3B/P
II2L3P
50
25
50
25
30
30
20
NETHERLANDS (NL)
G25
II2L3B/P
I3B/P
G30, G31
G30, G31
G20
G30, G31
G20
G30, G31
G20
G31
NORWAY (NO)
PORTUGAL (PT)
II2H3+
28-30, 37
20
28-30, 37
20
37, 50
20
30
II2H3+
II2H3P
SPAIN (ES)
G20
G30, G31
G20
SWEDEN (SE)
II2H3B/P
II2H3+
20
28-30, 37
UNITED KINGDOM (UK)
G30, G31
CE Standard
Required airflow for the combustion air supply is 2m3/h per kW.
2-6
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Connect the quick-disconnect hose to the fryer quick-disconnect fitting under the front of the
fryer and to the building gas line.
NOTE: Some fryers are configured for a rigid connection to the gas supply line. These units
are connected to the gas supply line at the rear of the unit.
When using thread compound, use very small amounts on male threads only. Use a pipe thread
compound that is not affected by the chemical action of LP gases (Loctite™ PST56765 Sealant
is one such compound). DO NOT apply compound to the first two threads. Doing so may allow
some of the compound to enter the gas stream, resulting in clogging of burner orifices and/or the
control valve.
2. Open the gas supply to the fryer and check all piping, fittings, and gas connections for leaks. A
soap solution should be used for this purpose.
3. Close the fryer drain valve and fill the frypot with water and boil-out solution to the bottom
OIL LEVEL line at the rear of the frypot. Light the fryer and perform the boil-out procedures
that are described in the “Lighting Instructions” and “Boiling Out the Frypot” topics found in
Chapter 3 of this manual.
DANGER
“Dry-firing” your unit will cause damage to the frypot and can cause a fire. Always
ensure that melted shortening, cooking oil, or water is in the frypot before firing your
unit.
4. The burner manifold pressure should be checked at this time by the local gas company or an
authorized service agent. The tables below and on the following page list the burner manifold
gas pressures for the various gas types that can be used with this equipment.
CE Standard
CE Standard
Burner Manifold Gas Pressures
for Fryers Manufactured After April 1999
Burner Manifold Gas Pressures
for Fryers Manufactured Through April 1999
Pressure (mbar)
Pressure (mbar)
Single
Vat
Dual
Vat
Single
Vat
Dual
Vat
Gas
Natural Gas Lacq
(G20) under 20 mbar
Gas
Natural Gas Lacq
(G20) under 20 mbar
7
7
7
10
6,5
9
Natural Gas Groningue *
(G25) under 25 mbar
Natural Gas Gronigue *
(G25) under 25 mbar
10
10
17
20
10
10
17
20
Natural Gas Groningue
(G25) under 20 mbar
Natural Gas Gronigue
(G25) under 20 mbar
10
9
Butane
(G30) at 28/30 or 50 mbar
Butane
(G30) at 28/30 or 50 mbar
17
16,5
18,5
Propane
(G31) under 37 or 50 mbar
Propane
(G31) under 37 or 50 mbar
20,2
* Belgian G25 = 7,0 mbar (single or dual)
* Belgian G25 = 7,0 mbar (single) or 6,5 (dual)
2-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Non-CE Standard
Burner Manifold Gas Pressures
Gas
Pressure
3" W.C.
0.73 kPa
Natural
8.25" W.C.
2.5 kPa
Propane
5. Check the programmed temperature or solid-state (analog) controller thermostat setting. (Refer
to the separate Frymaster Fryer Controllers User’s Manual furnished with your unit for the
setpoint programming instructions for your particular controller.)
2.5
Converting to Another Gas Type
DANGER
This appliance was configured at the factory for a specific type of gas. Converting
from one type of gas to another requires the installation of specific gas-conversion
components.
Switching to a different type of gas without installing the proper conversion
components may result in fire or explosion. NEVER ATTACH THIS APPLIANCE TO A
GAS SUPPLY FOR WHICH IT IS NOT CONFIGURED!
Conversion of this appliance from one type of gas to another should only be
performed by qualified, licensed, and authorized installation or service personnel, as
defined in Section 1.7 of this manual.
Pro H55 Series gas fryers manufactured for Non-CE countries use different burners for each type
gas. The burners in fryers built for Propane gas have a special gray-colored coating on the burner
tiles to enable them to withstand the higher caloric value of the Propane gas. Burners designed for
use in Propane units may be used in natural gas applications, but not vice versa.
Non-CE Gas Conversion Kits
Natural Gas to Propane (LP) Gas
Full Vat: Part Number 826-1145
Dual Vat: Part Number 826-1147
Propane (LP) Gas to Natural Gas
Full Vat: Part Number 826-1146
Dual Vat: Part Number 826-1148
Units manufactured for export to CE countries are equipped with “universal” burners that may be
used with either Natural (G20, G25) gas or Butane (G30) and Propane (G31) gasses.
CE Gas Conversion Kits for Units with Gas Valve 810-1715
G20 or G25 (Natural) to G30 or G31 Gas:
Part Number 826-1196
G30 or G31 to G20 or G25 (Natural) Gas:
Part Number 826-1197
2-8
Download from Www.Somanuals.com. All Manuals Search And Download.
CE GAS CONVERSION INSTRUCTIONS
1. Between G20- and G25-type Natural Gas, adjust the gas pressure at the regulator. (Refer to the
CE Standard Burner Manifold Gas Pressure Chart.) Do not change the orifice.
2. Between a 2nd family (G20 or G25) and a 3rd family gas (G30 Butane or G31 Propane):
a. Change the orifices.
b. Adjust the manifold pressure.
3. Affix the new label included with the conversion kit next to the existing rating plate stating that
the gas type has been converted. Remove any references to the previously used gas from the
existing rating plate. Conversion rating label PN 802-2144.
4. If the destination language changes, replace the labels. Call your local service agency or KES
for a label kit. The language of reference will be on the corner of the label.
2-9
Download from Www.Somanuals.com. All Manuals Search And Download.
THIS PAGE INTENTIONALLY LEFT BLANK
Download from Www.Somanuals.com. All Manuals Search And Download.
PRO H55 SERIES GAS FRYER
CHAPTER 3: OPERATING INSTRUCTIONS
3.1
Controller Operation and Programming
Pro H55 Series gas fryers can be equipped with any of the following controlling devices:
• Computer Magic III.5
• Solid State (Analog) Controller
• Digital Controller
• Basket Lift Timer
Refer to the appropriate section of the separate Frymaster Fryer Controllers User’s Manual furnished
with your fryer for the operating instructions for your specific controller.
3.2
Start-Up Procedure
WARNING
The on-site supervisor is responsible for ensuring that operators are made aware of
the inherent hazards of operating a hot oil filtering system, particularly the aspects
of oil filtration, draining and cleaning procedures.
CAUTION
If this is the first time the fryer is being used after installation, refer to Section 3.3,
Boil-Out Procedure.
CAUTION
The cooking oil/shortening capacity of the Pro H55 Series gas fryer is 50 lbs. (25
liters) at 70°F (21°C) for a full-vat and 25 lbs. (12.5 liters) at 70°F (21°C) for each half
of a dual-vat.
Before lighting the fryer, make sure the fryer is OFF and the frypot drain valve(s)
is/are closed. Remove the basket support rack(s), if installed, and fill the frypot to
the bottom OIL-LEVEL line.
If solid shortening is being used, make sure it is packed down into the bottom of the
frypot.
WARNING
Never operate this appliance with an empty frypot. The frypot must be filled with wa-
ter or cooking oil/shortening before lighting the burners. Failure to do so will dam-
age the frypot and may cause a fire.
3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Lighting the Fryer
1. Press the computer/controller ON/OFF switch to the OFF position.
For CE Fryers
For Non-CE Fryers
Placing the ON/OFF switch in the OFF
position also turns off the gas valve. Wait five
minutes before continuing with Step 2, which
will also turn on the gas valve.
After placing the ON/OFF switch in the OFF
position, turn the gas valve knob to the OFF
position. Wait 5 minutes, then turn the knob
to the ON postion and proceed with Step 2.
2. Press the computer/controller ON/OFF switch to the ON position and set the thermostat or
program the computer for normal cooking temperature.
3. If the burners fail to light, press the ON/OFF switch to the OFF position and wait 60 seconds.
Repeat step 2.
4. The fryer will automatically enter the melt cycle mode if the frypot temperature is below 180ºF
(82ºC). (NOTE: During the melt cycle, the burners will repeatedly fire for a few seconds, then
go out for a longer period.) When the frypot temperature reaches 180ºF (82ºC), the unit will
automatically switch to the heating mode. The burners will remain lit until the frypot
temperature reaches the programmed cooking temperature.
5. After the burners have been lit for at least 90 seconds, observe the flames through the burner
viewing ports located on each side of the combustion air blower.
Left Viewing Ports are
Right Viewing Ports
behind the motor
housings.
The optimum burn is a bright orange-red glow. If a blue flame is observed, or if there are dark spots
on a burner face, adjust the air gas mixture as follows: On the side of the blower housing opposite
3-2
Download from Www.Somanuals.com. All Manuals Search And Download.
the motor is a plate with a locking nut. Loosen the nut enough to allow the plate to be moved, then
adjust the position of the plate to open or close the air intake opening until a bright orange-red glow
is obtained. Carefully hold the plate in position and tighten the locking nut.
3.3
Boiling Out the Frypot
To ensure that the frypot is free of any contamination resulting from its manufacture, shipping, and
handling during installation, the frypot must be boiled out before first use. Refer to Drain and Clean
Frypot (page 5-1) for this procedure.
3.4
Shutting the Fryer Down
For short-term shut down during the workday, place the controller ON/OFF switch in the OFF
position and put the frypot covers in place (if the fryer is so equipped).
When shutting the fryers down at closing time, place the controller ON/OFF switch in the OFF
position. Then place the gas valve in the off position. See illustration below.
For CE Fryers
For Non-CE Fryers
Placing the ON/OFF switch in the OFF After placing the ON/OFF switch in the OFF
position also turns off the gas valve.
position, turn the gas valve knob to the OFF
position.
Put the frypot covers in place (if the fryer is so equipped).
3-3
Download from Www.Somanuals.com. All Manuals Search And Download.
THIS PAGE INTENTIONALLY LEFT BLANK
Download from Www.Somanuals.com. All Manuals Search And Download.
PRO H55 SERIES GAS FRYERS
CHAPTER 4: FILTRATION INSTRUCTIONS
WARNING
The on-site supervisor is responsible for ensuring that operators are made aware of
the inherent hazards of operating a hot oil filtering system, particularly the aspects
of oil filtration, draining and cleaning procedures.
4.1
Draining and Manual Filtering
DANGER
Draining and filtering of cooking oil must be accomplished with care to avoid the
possibility of a serious burn caused by careless handling. The oil to be filtered is at
or near 350°F (177°C). Ensure all hoses are connected properly and drain handles
are in their proper position before operating any switches or valves. Wear all
appropriate safety equipment when draining and filtering cooking oil.
DANGER
Allow oil to cool to 100°F (38°C) before draining into an appropriate container for
disposal.
DANGER
Do not drain more than one frypot at a time into the built-in filtration unit to avoid
overflow and spillage of hot oil.
DANGER
When draining oil into a disposal unit or portable filter unit, do not fill above the
maximum fill line located on the container.
If your fryer is not equipped with a built-in filtration system, the cooking oil must be drained into
another suitable container. (For safe, convenient draining and disposal of used cooking oil,
Frymaster recommends using the Frymaster Shortening Disposal Unit (SDU). The SDU is available
through your local distributor.)
1. Turn the fryer power switch to the OFF position. Screw the drainpipe (provided with your fryer)
into the drain valve. Make sure the drainpipe is firmly screwed into the drain valve and that the
opening is pointing down.
2. Position a metal container with a sealable cover under the drainpipe. The metal container must
be able to withstand the heat of the cooking oil and hold hot liquids. If you intend to reuse the
oil, Frymaster recommends that a Frymaster filter cone holder and filter cone be used when a
filter machine is not available. If you are using a Frymaster filter cone holder, be sure that the
cone holder rests securely on the metal container.
3. Open the drain valve slowly to avoid splattering. If the drain valve becomes clogged with food
particles, use the Fryer’s Friend (poker-like tool) to clear the blockage.
4-1
Download from Www.Somanuals.com. All Manuals Search And Download.
DANGER
NEVER attempt to clear a clogged drain valve from the front of the valve! Hot oil will
rush out creating the potential for severe burns.
DO NOT hammer on the drain valve with the cleanout rod or other objects. Damage
to the ball inside will result in leaks and will void the Frymaster warranty.
4. After draining the oil, clean all food particles and residual oil from the frypot. BE CAREFUL,
this material may still cause severe burns if it comes in contact with bare skin.
5. Close the drain valve securely and fill the frypot with clean, filtered or fresh cooking oil or solid
shortening to the bottom OIL-LEVEL line.
DANGER
When using solid shortening, pack the shortening down into the bottom of the
frypot. DO NOT operate the fryer with a solid block of shortening sitting in the upper
portion of the frypot. This will cause damage to the frypot and may cause a flash
fire.
4.2
Preparing the Built-In Filtration System for Use
The FootPrint Pro filtration system allows the oil in one frypot to be safely and efficiently filtered
while the other frypots in a battery remain in operation. The FootPrint Pro filtration system is
available in three different configurations:
•
•
•
Filter Paper – includes crumb tray, large hold-down ring, and metal filter screen.
Filter Pad – includes crumb tray, small hold-down ring, and metal filter screen.
Magnasol Filter – includes crumb tray and Magnasol filter assembly.
Section 4.2.1 covers preparation of the Filter Paper and Filter Pad configurations for use. Refer to
Section 4.2.2 for instructions on preparing the Magnasol Filter configuration for use. Operation of
all three configurations is the same and is covered in section 4.3. Disassembly and reassembly of the
Magnasol filter is covered in section 4.4.
4-2
Download from Www.Somanuals.com. All Manuals Search And Download.
4.2.1 Preparation for Use with Filter Paper or Filter Pad
1. Pull the filter pan out from the cabinet
Screen
and remove the crumb tray, hold-down
ring, filter paper and filter screen. (See
Figure 1) Clean all components with a
solution of detergent and hot water then
Filter Paper
dry thoroughly.
Crumb Tray
The filter pan is equipped with rollers in
rails, much like a kitchen drawer. The
pan may be removed for cleaning or to
gain access to interior components by
lifting the front of the pan to disengage
the front rollers, then pulling it forward
until the rear rollers clear the rails. The
pan cover must not be removed except
for cleaning, interior access, or to allow
a shortening disposal unit (SDU) to be
positioned under the drain.
Hold-Down Ring
Figure 1
2. Inspect the filter pan connection fitting
to ensure that both O-rings are in good
Inspect the filter
condition. (See Figure 2)
connection fitting
O-rings.
3. Then in reverse order, place the metal
filter screen in the center of the bottom
of the pan, then lay a sheet of filter paper
on top of the screen, overlapping on all
sides. (See Figure 1) If using a filter
pad, ensure the rough side of the pad is
up and lay the pad over the screen,
making sure that the pad is in between
the embossed ridges of the filter pan.
Figure 2
4. Position the hold-down ring over the
filter paper and lower the ring into the
pan, allowing the paper to rest on the
side of the filter pan. (See Figure 3)
Figure 3
4-3
Download from Www.Somanuals.com. All Manuals Search And Download.
5. When the hold-down ring is in position,
if using filter paper, sprinkle one cup of
filter powder evenly over the paper. (See
Figure 4)
If using a filter pad, position the hold
down ring on top of the pad. DO NOT
use filter powder with the pad.
Figure 4
6. Replace the crumb tray in the filter pan, then push the filter pan back into the fryer, positioning it
all the way to the back of the cabinet.
4.2.2 Preparation for Use with the Magnasol Filter Assembly
1. Pull the filter pan out from the cabinet
and remove the crumb tray and
Magnasol filter assembly. (See Figure
5)
The filter pan is equipped with rollers in
rails, much like a kitchen drawer. The
pan may be removed for cleaning or to
gain access to interior components by
lifting the front of the pan to disengage
the front rollers, then pulling it forward
until the rear rollers clear the rails. The
Figure 5
pan cover must not be removed except
for cleaning, interior access, or to allow
a shortening disposal unit (SDU) to be
positioned under the drain.
NOTE:
Refer to Section 4.4 for
Inspect the filter
screen O-ring.
instructions on how to disassemble and
reassemble the Magnasol filter screen
assembly.
Figure 6
2. Inspect the fitting on the bottom of the
Magnasol filter assembly to ensure that
the O-ring is present and in good
condition. (See Figure 6)
Inspect the filter
connection fitting
O-rings.
3. Inspect the filter pan connection fitting
to ensure that both O-rings are present
and in good condition. (See Figure 7)
Figure 7
4-4
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Replace the Magnasol filter assembly in the filter pan, ensuring that the fitting on the bottom of
the assembly is securely seated in the port in the bottom of the pan. Sprinkle one cup of the
Magnasol XL filter powder evenly over the screen.
5. Replace the crumb tray, then push the filter pan back into the fryer, positioning it all the way to
the back of the cabinet.
4.3
Operation of the Filter
DANGER
Draining and filtering of cooking oil must be accomplished with care to avoid the
possibility of a serious burn caused by careless handling. The oil to be filtered is at
or near 350°F (177°C). Ensure drain handles are in their proper position before
operating any switches or valves. Wear all appropriate safety equipment when
draining and filtering cooking oil.
DANGER
NEVER attempt to drain cooking oil from the fryer with the burners lit! Doing so will
cause irreparable damage to the frypot and may cause a flash fire. Doing so will also
void the Frymaster warranty.
1. Turn the fryer power OFF. Drain the
frypot into the filter pan by rotating the
valves counter clockwise to the right. If
necessary, use the Fryer's Friend clean-
out rod to clear the drain from inside the
frypot.
Open drain valves
by rotating 90°.
DANGER
Do not drain more than one frypot at a time into the built-in filtration unit to avoid
overflow and spillage of hot oil.
DANGER
NEVER attempt to clear a clogged drain valve from the front of the valve! Hot oil will
rush out creating the potential for severe burns.
DO NOT hammer on the drain valve with the cleanout rod or other objects. Damage
to the ball inside will result in leaks and will void the Frymaster warranty.
4-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Install the Power
Shower in the frypot
to be filtered.
2. If an optional Power Shower is included,
install it now. NOTE: Verify that the
Power Shower O-ring and gasket are
present and in good condition and that
the clean-out screws are installed at each
corner.
Snap the optional Power Shower into position.
DANGER
If the fryer includes a Power Shower, DO NOT operate the filter without the Power
Shower in place. Hot oil will spray out of the fryer and cause injury.
3. After the cooking oil has drained from
the frypot, pull the filter handle forward
(outward) to start the pump and begin
the filtering process. There may be a
slight delay before the pump activates.
Pull filter handle forward
to activate pump.
4. The filter pump draws the cooking oil through the filter medium and circulates it back up to and
through the frypot during a 5-minute process called polishing. Polishing cleans the oil by
trapping solid particles in the filter medium.
5. After the oil is filtered (about 5 minutes), close the drain valve and allow the fryer to refill. Let
the filter pump run 10 to 12 seconds after the oil begins to bubble (or sputter from the Power
Shower openings, if installed). Turn the filter off, remove the Power Shower if installed, and let
it drain.
4-6
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
The filter pump is equipped with a manual reset switch in case the filter motor
overheats or an electrical fault occurs. If this switch trips, turn off power to the filter
system and allow the pump motor to cool 20 minutes before attempting to reset the
switch (see photo below).
Filter Pump Reset Switch
6. Ensure the drain valve is fully closed. (If the drain valve is not fully closed, the fryer will not
operate.) Turn the fryer ON and allow the cooking oil to reach setpoint.
DANGER
The crumb tray in fryers equipped with a filter system must be emptied into a
fireproof container at the end of frying operations each day. Some food particles can
spontaneously combust if left soaking in certain shortening material.
WARNING
Do not bang fry baskets or other utensils on the fryer’s joiner strip. The strip is
present to seal the joint between the fry vessels. Banging fry baskets on the strip to
dislodge shortening will distort the strip, adversely affecting its fit. It is designed for
a tight fit and should only be removed for cleaning.
4-7
Download from Www.Somanuals.com. All Manuals Search And Download.
4.4
Disassembly and Reassembly of the Magnasol Filter
Dissassembly
1. Grasp the frame with your thumbs on the handles at the corner of the assembly and pull outward
in opposite directions to separate the frame at the corner. Continue to open the frame (it will
pivot at the opposite corner) until the outer screens and grid can be removed from the frame.
Step 2 - Separate
the outer screens
and grid.
Step 1 - Grasp frame with
thumbs on these handles and
pull frame appart at corner.
2. Separate the outer screens and grid.
Cleaning
1. Clean the two frame pieces, outer screens, and grid using a good quality degreaser and hot water
from a spray nozzle. The groove in the seal frame pieces can be cleaned with the edge of a
Scotch-Brite™ or similar cleaning pad.
2. At each scheduled boil-out, disassemble the leaf filter assembly and place in the frypot being
boiled out. Follow the boil-out procedure in Section 5.1.2 of this manual.
3. Allow all filter assembly components to air dry or thoroughly dry with clean towels before
reassembling.
Reassembly
1. Place the two outer screens together and align their edges (see illustration on following page).
2. Insert the screens into one of the frame halves (it doesn’t matter which one). Ensure that the
fitting in the bottom screen is on the opposite side of the frame from the handle.
3. Slip the grid between the screens, ensuring that the grid is centered between the edges of the
screens.
4. Connect the other half of the frame at the corner opposite the handles and pivot the frame onto
the free edges of the screen.
4-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Steps 1 and 2 - Stack outer screens
and insert edges into frame.
Step 3 - Insert grid between screens
after screens have been positioned in
frame.
Step 4 - Connect corner then pivot
frame over free edges of screens.
Handle
4.5
Draining and Disposing of Waste Oil
When your cooking oil has reached the end of its usable life, drain the oil into an appropriate
container for transport to the disposal container. Frymaster recommends the use of the Frymaster
Shortening Disposal Unit (SDU). NOTE: If using an SDU built before January 2004 the filter pan
cover must be removed to allow the unit to be positioned beneath the drain. To remove the lid, lift up
on the front edge and pull it straight out of the cabinet. Refer to the documentation furnished with
your disposal unit for specific operating instructions. If a shortening disposal unit is not available,
allow the oil to cool to 100°F (38°C), then drain the oil into a metal stockpot or similar metal
container. When draining is finished, close the fryer drain valve securely.
DANGER
Allow oil to cool to 100°F (38°C) before draining into an appropriate container for
disposal.
When draining oil into a disposal unit, do not fill above the maximum fill line located
on the container.
4-9
Download from Www.Somanuals.com. All Manuals Search And Download.
4.6
Using the Optional Rear-Discharge Oil Disposal
1. Ensure the filter pan is clean and ready for filtering. DO
NOT discharge oil through a dirty or incomplete filter
pan.
2. Ensure the oil is at operating temperature.
3. Turn the fryer off. Wear protective clothing and use
caution. Hot oil can cause serious injury.
4. Open the drain valve of the frypot with oil to be
discarded. Drain only one frypot at a time.
5. With the frypot drained and the oil to be discarded in the
filter pan, close the drain valve. Ensure all other drain
valves and oil-return valves are closed.
6. Ensure the oil disposal reservoir is not full and the fryer
is properly connected to the oil disposal system.
7. Discharge the oil by pressing down on the discharge
valve handle. The filter pump will come on and the oil
will be pumped from the filter pan. Turn the pump off
by lifting the discharge handle to the off position when
the filter pan empties. Repeat steps 1-7 if necessary to
discharge the oil from other frypots. DO NOT discharge
water or other liquids through the filter system.
8. Refill the fryer with fresh oil.
The oil discharge valve handle is
shown in the OFF position. Push it
down to discharge oil from the filter
pan.
4-10
Download from Www.Somanuals.com. All Manuals Search And Download.
PRO H55 SERIES GAS FRYERS
CHAPTER 5: PREVENTIVE MAINTENANCE
5.1
Fryer Preventive Maintenance Checks and Service
DAILY CHECKS AND SERVICE
Inspect Fryer and Accessories for Damage
Look for loose or frayed wires and cords, leaks, foreign material in frypot or inside cabinet, and any
other indications that the fryer and accessories are not ready and safe for operation.
Clean Fryer Cabinet Inside and Out
Clean inside the fryer cabinet with dry, clean cloth. Wipe all accessible metal surfaces and compo-
nents to remove accumulations of oil or shortening and dust.
Clean the outside of the fryer cabinet with a clean, damp cloth soaked with dishwashing detergent,
removing oil, dust, and lint from the fryer cabinet.
DANGER
Never attempt to clean fryer during the cooking process or when the frypot is filled
with hot oil. If water comes in contact with oil heated to cooking temperature, it can
cause the oil to splatter and severely burn nearby personnel.
WEEKLY CHECKS AND SERVICE
Drain and Clean Frypot
During normal usage of your fryer, a deposit of carbonized cooking oil will gradually form on the
inside of the frypot. This deposit must be periodically removed to maintain your fryer’s efficiency.
DANGER
Allow oil to cool to 100ºF (38ºC) or lower before draining to an appropriate container
for disposal.
1. Drain the frypot in accordance with Section 4.1 (page 4-1), but do not refill with cooking oil.
2. After draining the frypot, clean all food particles and residual oil from the frypot and filter pan
(if so equipped). BE CAREFUL, this material may still cause severe burns if it comes in contact
with bare skin.
3. Close the drain valve securely and fill the frypot with a solution of automatic dishwasher
detergent and water (or commercially available boil-out solution) to the bottom OIL-LEVEL
line.
5-1
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Set the thermostat to 195ºF (91ºC) or program the computer for Boil-Out (see separate Frymas-
ter Fryer Controllers User’s Manual) and simmer the solution for 1 hour.
WARNING
Never leave the fryer unattended during this process. If the solution overflows,
press the ON/OFF switch to the OFF position immediately.
5. After the solution has simmered for 1 hour, press the ON/OFF switch to the OFF position and
allow the solution to cool.
6. Drain the solution into a suitable container (NOT the built-in filtration system filter pan or
the Shortening Disposal Unit) and thoroughly wipe the frypot with a clean towel.
7. Close the drain valve and fill the frypot with clean, cold water and drain into a suitable container
(NOT the built-in filtration system filter pan or the Shortening Disposal Unit). Repeat the
rinse process again, and then wipe frypot with a clean, dry towel.
DANGER
Ensure that the frypot is completely free of water before filling with cooking oil or
shortening. When the oil or shortening is heated to cooking temperature, water in
the frypot will cause splattering.
Clean Filter Pan, Detachable Parts and Accessories
As with the frypot, a deposit of carbonized oil will accumulate on the filter pan and detachable parts
and accessories such as baskets, sediment trays, or fish plates.
Wipe the filter pan and all detachable parts and accessories with a clean cloth dampened with a
detergent solution (or the parts can be run through a dishwasher). Rinse and thoroughly dry each
part. DO NOT use steel wool or abrasive pads to clean these parts. The scratches that result from
such scrubbing make subsequent cleanings more difficult.
WARNING
Use a commercial-grade cleaner formulated to effectively clean and sanitize
food-contact surfaces. Read the directions for use and precautionary statements be-
fore use. Particular attention must be paid to the concentration of cleaner and the
length of time the cleaner remains on the food-contact surfaces.
5-2
Download from Www.Somanuals.com. All Manuals Search And Download.
MONTHLY CHECKS AND SERVICE
Check Calibration of Analog Controller Thermostat Control Knob
(This check applies only to units equipped with Analog Controllers)
1. Insert a good-grade thermometer or pyrometer probe into the oil, with the end touching the fryer
temperature-sensing probe and set the thermostat knob to frying temperature.
2. After the set temperature is reached, let the burner cycle on and off automatically three times to
allow the cooking oil temperature to become uniform. If necessary, stir to get all shortening in
the bottom of the frypot melted.
3. When the burner starts for the fourth time, the thermometer/pyrometer reading should be within
± 5ºF (2ºC) of the thermostat knob setting. If it is not, calibrate as follows:
a. Loosen setscrew in thermostat control knob until the knob will rotate freely on its shaft.
b. Rotate the knob until the index line on the knob is aligned with the marking that corresponds
to the thermometer or pyrometer reading.
c. Hold the knob and carefully tighten the setscrew.
d. Recheck the thermometer/pyrometer reading against the thermostat knob setting the next
time the burner lights.
e. Repeat steps 3.a. through 3.d. until the thermometer/pyrometer reading and knob setting
agree within ± 5ºF (2ºC). If calibration cannot be obtained for any reason, call a Factory
Authorized Service Center for assistance.
5. Remove the thermometer or pyrometer.
Check Computer Magic III.5 Set Point Accuracy
(This check applies only to units equipped with Computer Magic III.5 Controllers.)
1. Insert a good-grade thermometer or pyrometer probe into the oil, with the end touching the fryer
temperature-sensing probe.
2. When the computer display shows a series of four dashes “----” with no dot between the first and
second dashes (indicating that the frypot contents are within the cooking range), press the
switch once to display the temperature of the cooking oil as sensed by the temperature probe.
3. Press the
switch twice to display the set point.
4. Note the temperature on the thermometer or pyrometer. All three readings should be within
± 5ºF (2ºC) of each other. If not, contact a Factory Authorized Service Center for assistance.
5-3
Download from Www.Somanuals.com. All Manuals Search And Download.
QUARTERLY CHECKS AND SERVICE
Clean Combustion Air Blower Assembly
1. Disconnect the blower wiring harness and remove the four blower mounting nuts.
Blower
assembly
mounting nuts
Wiring connection
2. Remove the three fasteners that secure the blower motor assembly to the blower housing, and
separate the two components.
Remove these fasteners.
3. Wrap the motor with plastic wrap to prevent water from entering it. Spray degreaser or
detergent on the blower wheel and the blower housing. Allow it to soak for five minutes. Rinse
the wheel and housing with hot tap water, then dry with a clean cloth.
Wrap the motor and wires
with plastic wrap or a
plastic bag.
Blower Housing
Blower Wheel
5-4
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Remove the plastic wrap from the blower motor assembly. Reassemble the blower motor
assembly and blower housing. Reinstall the blower assembly in the fryer.
5. Reinstall the blower shield or shield assembly.
6. Light the fryer in accordance with the procedure described in Chapter 3, Section 3.1.
7. After the burners have been lit for at least 90 seconds, observe the flames through the burner
viewing ports located on each side of the combustion air blower.
Left Viewing
Port is Behind
Motor
(NOTE: Blower
shield omitted
for clarity.)
Right
Viewing
Port
The air/gas mixture is properly adjusted when the burner manifold pressure is in accordance with the
applicable table on page 2-7 and the burners display a bright orange-red glow. If a blue flame is
observed, or if there are dark spots on a burner face, the air/gas mixture requires adjustment.
On the side of the blower housing opposite the motor is a plate with one or two locking nuts.
Loosen the nut(s) enough to allow the plate to be moved, then adjust the position of the plate to open
or close the air intake opening until a bright orange-red glow is obtained. Carefully hold the plate in
position and tighten the locking nut(s).
SOME CE BLOWER ASSEMBLIES
MAY BE CONFIGURED THIS WAY
TYPICAL BLOWER ASSEMBLY
5-5
Download from Www.Somanuals.com. All Manuals Search And Download.
SEMI-ANNUAL CHECKS AND SERVICE
Clean Gas Valve Vent Tube
NOTE: This procedure is not required for fryers configured for export to CE
countries.
1. Set the fryer power switch and the gas valve to the OFF position.
2. Carefully unscrew the vent tube from the gas valve. NOTE: The vent tube may be straightened
for ease in removal.
3. Pass a piece of ordinary binding wire (.052 inch diameter) through the tube to remove any
obstruction.
4. Remove the wire and blow through the tube to ensure it is clear.
5. Reinstall the tube and bend it so that the opening is pointing downward.
Check Burner Manifold Pressure
DANGER
This task should be performed by qualified service personnel only. Contact your
FASC to arrange this service.
5.2
Built-in Filtration System Preventive Maintenance Checks and Service
WARNING
Never operate the filter system without cooking oil or shortening in the system.
WARNING
Never use the filter pan to transport old oil to the disposal area.
WARNING
Never drain water into the filter pan. Water will damage the filter pump.
There are no periodic preventive maintenance checks and services required for your FootPrint Pro
Filtration System other than daily cleaning of the filter pan with a solution of hot water and
detergent.
If you notice that the system is pumping slowly or not at all, verify that the filter pan screen is on the
bottom of the filter pan, with the paper on top of the screen. (If the unit is equipped with a Magnasol
filter screen rather than with the standard screen and paper system, verify that the O-ring on the
bottom fitting of the screen in present and in good condition.) Verify that the two O-ring(s) on the
fitting at the right front of the filter pan are present and in good condition.
5-6
Download from Www.Somanuals.com. All Manuals Search And Download.
GASKET
O-RING
CLEAN-OUT PLUGS
If the system is equipped with a Power Shower, drain the Power Shower completely after each use.
If oil is leaking at the point where the Power Shower plugs into the frypot, verify that the O-ring and
gasket on the connection fitting are present and in good condition. If you suspect blockage, unscrew
the clean-out plugs at each corner of the frame. Place the frame in a pan of hot water for several
minutes to melt any accumulation of solidified oil/shortening. Use a long, narrow bottlebrush with
hot water and detergent to clean inside the tubes. If necessary, insert a straightened paper clip or
similarly sized wire into the holes in the frame to remove any solidified shortening or other
blockages. Rinse with hot water, dry thoroughly, and reinstall the plugs before using.
DANGER
Failure to reinstall the clean-out plugs in the Power Shower will cause hot oil to
spray out of the frypot during the filtering process, creating an extreme burn hazard
to personnel.
5.3
Annual/Periodic System Inspection
This appliance should be inspected and adjusted periodically by qualified service personnel as
part of a regular kitchen maintenance program.
Frymaster recommends that a Factory Authorized Service Technician inspect this appliance at
least annually as follows:
Fryer
• Inspect the cabinet inside and out, front and rear for excessive oil.
• Verify that the flue opening is not obstructed by debris or accumulations of solidified oil or
shortening.
• Verify that burners and associated components (i.e. gas valves, pilot assemblies, ignitors, etc.)
are in good condition and functioning properly. Inspect all gas connections for leaks and verify
that all connections are properly tightened.
• Verify that the burner manifold pressure is in accordance with that specified on the appliance’s
rating plate.
5-7
Download from Www.Somanuals.com. All Manuals Search And Download.
• Verify that the temperature and high-limit probes are properly connected, tightened and
functioning properly, and that probe guards are present and properly installed.
• Verify that component box components (i.e. computer/controller, transformers, relays, interface
boards, etc.) are in good condition and free from oil and other debris. Inspect the component box
wiring and verify that connections are tight and that wiring is in good condition.
• Verify that all safety features (i.e. drain safety switches, reset switches, etc.) are present and
functioning properly.
• Verify that the frypot is in good condition and free of leaks and that the frypot insulation is in
serviceable condition.
• Verify that wiring harnesses and connections are tight and in good condition.
Built-In Filtration System
• Inspect all oil-return and drain lines for leaks and verify that all connections are tight.
• Inspect the filter pan for leaks and cleanliness. If there is a large accumulation of crumbs in the
crumb basket, advise the owner/operator that the crumb basket should be emptied into a fireproof
container and cleaned daily.
• Verify that all O-rings and seals (including those on the Power Shower if applicable and on the
quick-disconnect fitting) are present and in good condition. Replace O-rings and seals if worn or
damaged.
• Check filtration system integrity as follows:
− Verify that filter pan cover is present and properly installed.
−
With the filter pan empty, place each oil return handle, one at a time, in the ON position.
Verify that the pump activates and that bubbles appear in the cooking oil/shortening (or that
gurgling is heard from the Power Shower port if applicable) of the associated frypot.
− Close all oil return valves (i.e., place all oil return handles in the OFF position). Verify
proper functioning of each oil return valve by activating the filter pump using the lever on
one of the oil return microswitches. No air bubbles should be visible in any frypot (or no
gurgling should be heard from the Power Shower ports if applicable).
− Verify that the filter pan is properly prepared for filtering, then drain a frypot of oil heated to
350°F (177°C) into the filter pan and close the frypot drain valve. Place the oil return handle
in the ON position. Allow all cooking oil to return to the frypot (indicated by bubbles in the
cooking oil or on units with Power Showers, cessation of oil flow from the Power Shower).
Return the oil return handle to the OFF position. The frypot should have refilled in no more
than 2 minutes and 30 seconds.
5-8
Download from Www.Somanuals.com. All Manuals Search And Download.
PRO H55 SERIES GAS FRYERS
CHAPTER 6: OPERATOR TROUBLESHOOTING
6.1
Introduction
This chapter provides an easy reference guide to some of the common problems that may occur
during the operation of your equipment. The troubleshooting guides that follow are intended to help
you correct, or at least accurately diagnose, problems with your equipment. Although the chapter
covers the most common problems reported, you may encounter problems that are not covered. In
such instances, the Frymaster Technical Services staff will make every effort to help you identify
and resolve the problem.
When troubleshooting a problem, always use a process of elimination starting with the simplest
solution and working through to the most complex. Most importantly, always try to establish a clear
idea of why a problem has occurred. Part of your corrective action involves taking steps to ensure
that it doesn’t happen again. If a controller malfunctions because of a poor connection, check all
other connections while you’re at it. If a fuse continues to blow, find out why. Always keep in mind
that failure of a small component may often be indicative of potential failure or incorrect functioning
of a more important component or system.
Some of the troubleshooting actions that are recommended in this chapter involve removing suspect
components and substituting components that are known to be good. Whenever this in indicated,
refer to Sections 6.6 for specific instructions
If you are in doubt as to the proper action to take, do not hesitate to call the Frymaster Technical
Service Department or your local Frymaster Factory Authorized Service Center for assistance.
Before calling a servicer or the Frymaster HOTLINE (1-800-551-8633):
• Verify that electrical cords are plugged in and that circuit breakers are on.
• Verify that gas line quick-disconnects are properly connected.
• Verify that any gas line cutoff valves are open.
• Verify that frypot drain valves are fully closed.
DANGER
Hot cooking oil will cause severe burns. Never attempt to move this appliance when
filled with hot cooking oil or to transfer hot cooking oil from one container to another.
DANGER
This equipment should be unplugged when servicing, except when electrical circuit
tests are required. Use extreme care when performing such tests.
This appliance may have more than one electrical power supply connection point.
Disconnect all power cords before servicing.
Inspection, testing, and repair of electrical components should be performed by an
authorized service agent only.
6-1
Download from Www.Somanuals.com. All Manuals Search And Download.
6.2
Troubleshooting Fryers with Computer Magic III.5, Basket Lift Timer, or Digital
Controller
PROBLEM
PROBABLE CAUSES
CORRECTIVE ACTION
A. Press the ON/OFF switch to turn
the controller on.
A. Controller not turned on.
B. Verify that the fryer is plugged in
and that the circuit breaker is not
tripped.
B. No power to fryer.
C. If available, substitute a harness
known to be good for the suspect
harness. If the fryer functions
correctly, order replacement
harness from FASC.
No display on
computer or
controller.
C. Damaged computer/controller
wiring harness.
D. If available, substitute a
computer/controller known to be
working for the suspect
D. Failed computer/controller.
computer/controller. If the fryer
functions correctly, order
replacement from FASC.
If available, substitute a harness
known to be good for the suspect
harness. If the fryer functions
correctly, order replacement
harness from FASC.
Display shows
with alarm
Damaged computer/controller
wiring harness or connector.
sounding.
A. Drain valve not fully closed.
A. Press the ON/OFF switch off,
close the drain valve(s)
completely, then press the
ON/OFF switch on.
B. Turn the gas valve knob to the
ON position.
B. Gas valve is not turned on.
Display shows
with alarm
sounding. Heating
indicator is on, but
burners will not
light.
C. Verify that any in-line manual
shut off valve is open. Verify that
gas main cut off valve is open.
D. Verify that the quick-disconnect
fitting on the flexible gas line is
firmly connected to the fryer.
E. Verify that combustion air blower
is running. If not, call FASC for
service. If combustion air blower
is functional, clean and adjust per
instructions in Chapter 5 of this
manual.
C. Manual gas shut off valve closed.
D. Improperly connected quick-
disconnect fitting on gas line.
E. Obstructed or failed combustion
air blower.
6-2
Download from Www.Somanuals.com. All Manuals Search And Download.
PROBLEM
PROBABLE CAUSES
CORRECTIVE ACTION
A. If available, substitute a
computer/controller known to be
working for the suspect
Display shows
,
A. Failed computer/controller.
computer/controller. If the fryer
functions correctly, order
replacement from FASC.
heating indicator
cycles on and off
normally, but
B. If available, substitute a harness
known to be good for the suspect
harness. If the fryer functions
correctly, order replacement
harness from FASC.
burners will not
light and blower is
not running.
B. Damaged computer/controller
wiring harness.
Fryer is slow coming
out of melt cycle.
Display shows
Dirty or obstructed combustion air
blower.
Clean and adjust per instructions
in Chapter 5 of this manual.
a short time
after coming out of
melt cycle.
Fryer is operating
normally, but
Dirty or obstructed combustion air
blower.
Clean and adjust per instructions
in Chapter 5 of this manual.
recovery is slow
when cooking.
A. Dirty or obstructed combustion air A. Clean and adjust per instructions
Fryer is operating
normally, but
produces a popping
sound when burners
ignite.
blower.
in Chapter 5 of this manual.
B. Dirty or obstructed gas valve vent B. Clean per instructions in Chapter
tube (non-CE fryers only).
C. Malfunctioning combustion air
blower.
5 of this manual.
C. If blower is slow to come up to
speed, contact FASC for service.
If available, substitute a
Display shows
and alarm
sounds, but fryer
operates normally
(false alarm).
computer/controller known to be
working for the suspect
computer/controller. If the fryer
functions correctly, order
replacement from FASC.
If available, substitute a
computer/controller known to be
working for the suspect
computer/controller. If the fryer
functions correctly, order
replacement from FASC.
Failed computer/controller.
Failed computer/controller.
Computer will not
go into program
mode or some
buttons do not
actuate.
Heat indicator is on
and blower is
running, but burner
will not ignite.
Blown fuse on interface board or
ignition module.
Replace fuse.
6-3
Download from Www.Somanuals.com. All Manuals Search And Download.
PROBLEM
PROBABLE CAUSES
CORRECTIVE ACTION
If available, substitute a
computer/controller known to be
working for the suspect
computer/controller. If the fryer
functions correctly, order
replacement from FASC.
Heat indicator off
upon initial startup.
Display shows
Failed computer/controller.
or
with alarm
sounding.
6.3
Troubleshooting Fryers with Solid State (Analog) Controller
PROBLEM
PROBABLE CAUSES
A. No power to fryer.
CORRECTIVE ACTION
A. Verify that the fryer is plugged in
and that the circuit breaker is not
tripped.
B. If available, substitute a harness
known to be good for the suspect
harness. If the fryer functions
correctly, order replacement
harness from FASC.
B. Damaged controller wiring
harness.
Power switch ON, no
lights on controller,
fryer does not heat.
C. If available, substitute a controller
known to be working for the
suspect controller. If the fryer
functions correctly, order
C. Failed controller.
replacement from FASC.
If available, substitute a harness
known to be good for the suspect
harness. If the fryer functions
correctly, order replacement
harness from FASC.
Power light ON,
trouble light ON,
heating mode light
OFF.
Damaged controller wiring
harness.
A. Press the ON/OFF switch off,
close the drain valve(s)
A. Drain valve not fully closed.
completely, then press the
ON/OFF switch on.
B. Turn the gas valve knob to the
ON position.
B. Gas valve is not turned on.
C. Verify that any in-line manual
shut off valve is open. Verify that
gas main cut off valve is open.
D. Verify that the quick-disconnect
fitting on the flexible gas line is
firmly connected to the fryer.
E. Verify that combustion air blower
is running. If not, call FASC for
service. If combustion air blower
is functional, clean and adjust per
instructions in Chapter 5 of this
manual.
Power light ON,
trouble light ON,
heating mode light
ON. Burners do not
ignite.
C. Manual gas shut off valve closed.
D. Improperly connected quick-
disconnect fitting on gas line.
E. Obstructed or failed combustion
air blower.
6-4
Download from Www.Somanuals.com. All Manuals Search And Download.
PROBLEM
PROBABLE CAUSES
CORRECTIVE ACTION
A. If available, substitute a controller
known to be working for the
suspect controller. If the fryer
functions correctly, order
Heating mode light A. Failed controller.
cycles on and off
normally. Blower
replacement from FASC.
not running and
burners will not
B. If available, substitute a harness
known to be good for the suspect
harness. If the fryer functions
correctly, order replacement
harness from FASC.
B. Damaged controller wiring
ignite.
harness.
Fryer is slow coming
out of melt cycle.
Heating mode light
is ON. Trouble light
comes on a short
time after coming
out of melt cycle.
Fryer is operating
normally, but
Dirty or obstructed combustion air
blower.
Clean and adjust per instructions
in Chapter 5 of this manual.
Dirty or obstructed combustion air
blower.
Clean and adjust per instructions
in Chapter 5 of this manual.
recovery is slow
when cooking.
A. Obstructed combustion air
blower.
B. Dirty or obstructed gas valve vent B. Clean per instructions in Chapter
tube (non-CE fryers only).
C. Malfunctioning combustion air
blower.
A. Clean and adjust per instructions
in Chapter 5 of this manual.
Fryer is operating
normally, but
produces popping
sound when burners
ignite.
5 of this manual.
C. If blower is slow to come up to
speed, contact FASC for service.
Heating mode light
is on and blower is
running, but burner
will not ignite.
Blown fuse on interface board or
ignition module.
Replace fuse.
A. If available, substitute a controller
known to be working for the
suspect controller. If the fryer
functions correctly, order
Heating mode light
is cycling on and off A. Failed controller.
normally and fryer
is operating
replacement from FASC.
normally, but
trouble light is on
continuously (false
alarm).
B. If available, substitute a harness
known to be good for the suspect
harness. If the fryer functions
correctly, order replacement
harness from FASC.
B. Damaged controller wiring
harness.
6-5
Download from Www.Somanuals.com. All Manuals Search And Download.
PROBLEM
PROBABLE CAUSES
CORRECTIVE ACTION
Heating mode light
is ON with power
switch in OFF
If available, substitute a controller
known to be working for the
suspect controller. If the fryer
functions correctly, order
position. After
initial startup, fryer
continues to heat
until trouble light
comes on. Frypot
temperature is
Failed controller.
replacement from FASC.
above 410F (210°C).
6.4
Troubleshooting the Built-in Filtration System
PROBLEM
PROBABLE CAUSES
CORRECTIVE ACTION
A. If the pump runs normally after
resetting the thermal overload
switch, the pump was overheated.
A. Thermal overload switch has
tripped on an overheated motor.
Test: If the pump stopped
suddenly during the filtering
process, especially if after several
filtering cycles, the pump motor
has probably overheated. Place
the filter handle in the OFF
position, allow the pump to cool
for at least 45 minutes, and then
press the reset button on the pump
motor. Attempt to activate the
pump.
Always filter with the cooking oil
at or near frying temperature.
Allow the pump motor to cool off
for about ten minutes after
filtering two full frypots one after
the other.
Check the filter paper between
filterings. Replace the paper if
there is a large accumulation of
sediment.
Pump won’t start.
OR
B. Failed filter handle microswitch.
Pump stops during
filtering.
Test: If this is a multi-pot fryer,
attempt to operate the pump using
a different handle. If the pump
starts, the handle microswitch is
either out of alignment or has
failed.
B. If the switch is loose, tighten the
nuts and bolts holding it in place,
ensuring that when the handle is
placed in the ON position, the
lever on the microswitch is
pressed firmly against the switch.
When the handle is placed in the
ON position, the lever on the
microswitch should be firmly
pressed against the switch. If so,
the switch has failed. If not, the
switch is loose and/or misaligned.
If the switch has failed, call
FASC.
6-6
Download from Www.Somanuals.com. All Manuals Search And Download.
PROBLEM
PROBABLE CAUSES
C. Pump blockage.
CORRECTIVE ACTION
C. Pump blockages are usually
caused by sediment build-up in
the pump due to improperly sized
or installed filter paper and failure
to use the crumb screen. Call
FASC to have blockage cleared.
Test: Close the drain valve. Place
the filter handle in the OFF
position, allow the pump to cool
for at least 45 minutes, and then
press the reset button on the pump
motor. Pull the filter pan from the
unit and then activate the pump.
If the pump motor hums and then
stops, the pump is blocked.
(Continued from
previous page.)
Ensure that filter paper is of the
proper size and is installed
properly, and that the crumb
screen is used.
A. To properly filter, the oil should
be at or near 350°F (177°C). At
temperatures lower than this, the
oil becomes too thick to pass
through the filter medium easily,
resulting in much slower oil
return and eventual overheating of
the filter pump motor.
A. Cooking oil is too cold for
filtering.
B. Improperly installed or prepared
filter pan components.
Pump starts, but no
transfer takes place
or the transfer is
very slow.
B. Remove the oil from the filter pan
and replace the filter paper,
Test: Close the drain valve.
Move the filter handle to the OFF
position, pull the filter pan (and
Power Shower, if so equipped)
from the unit. Move the filter
handle to the ON position.
ensuring that the filter screen is in
place under the paper.
C. If this does not correct the
problem, the filter suction tube is
probably blocked. Remove the
blockage using a thin, flexible
wire. If unable to remove the
blockage, call FASC.
If a strong stream of air is being
pumped out of the oil return port
(or the Power Shower port), the
problem is with the filter pan
components.
A. Plugged openings or solidified
shortening in the Power Shower.
A. Clean the Power Shower per
instructions in Chapter 5 of this
manual.
Test: Look for oil squirting out
around the Power Shower gasket
but not coming out of the holes
around the frame. If so, Power
Shower is obstructed.
Power Shower is not
spraying properly.
B. Missing/worn o-rings and gasket B. Verify that o-rings and gasket are
on Power Shower. present and in good condition.
6-7
Download from Www.Somanuals.com. All Manuals Search And Download.
PROBLEM
PROBABLE CAUSES
C. Missing paper in filter pan. (This
causes too much pressure in the
oil return lines, resulting in a
strong flow through the Power
Shower, but also squirting of oil
from around the gasket.)
CORRECTIVE ACTION
(Continued from
previous page.)
C. Verify that filter paper is properly
installed in the filter pan.
6.5
Troubleshooting the Basket Lift
PROBLEM
Basket lift
movement is jerky
and/or noisy.
PROBABLE CAUSES
Basket lift rods need lubrication.
CORRECTIVE ACTION
Lubricate basket lift rods with
Lubriplate™ or equivalent light
white grease.
6-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Frymaster, L.L.C., 8700 Line Avenue, PO Box 51000, Shreveport, Louisiana 71135-1000
Shipping Address: 8700 Line Avenue, Shreveport, Louisiana 71106
TEL 1-318-865-1711
FAX (Parts) 1-318-219-7140
FAX (Tech Support) 1-318-219-7135
SERVICE HOTLINE
1-800-551-8633
819-5991
SEPTEMBER 2005
PRINTED IN THE UNITED STATES
Download from Www.Somanuals.com. All Manuals Search And Download.
|