All about the
Use&Care
of your
Room Air Conditioner
TABLE OF CONTENTS
Important Safety Instructions ............................... 2-3
Product Registration ............................................. 4
Packaging ........................................................... 4
Normal Sounds .................................................... 4
Operating Instructions .......................................... 5-6
Care and Cleaning .............................................. 7
Energy Saving Ideas ........................................... 7
Before You Call ................................................... 8
Major Appliance Warranty ................................... 9
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Instructions
SAFETY PRECAUTIONS
CAUTION! Avoid Injury or damage to the unit or other property
Provide occasional ventilation during use. Do not direct airflow at fireplaces or other heat related sources as this could cause flare ups or make
units run excessively.
Do not climb on or place objects on outdoor part of the unit.
Do not hang objects off the unit.
Do not place containers with liquids on the unit.
Turn off the air conditioner at the power source when it will not be used for an extended period of time.
Periodically check the condition of the unit’s installation accessories for any damage.
Do not apply heavy pressure to the radiator fins of the unit.
Operate the unit with air filter in place.
Do not block or cover the intake grille, discharge area and outlet ports.
Ensure that any electrical/electronic equipment is one yard away from the unit.
Do not use or store flammable gases near the unit.
READ THIS SECTION BEFORE ATTEMPTING TO OPERATE AIR CONDITIONER.
Unit must be upright for one hour prior to operating.
The power supply cord contains a current device that senses damage to the power cord. To test
your power supply cord do the following:
Plug in the Air Conditioner.
The power supply cord will have TWO buttons on the plug head. Press the TEST button. You will
notice a click as the RESET button pops out.
Plug in &
Press the RESET button. Again you will notice a click as the button engages.
press RESET
The power supply cord is now supplying electricity to the unit.
NOTE:
Do not use this device to turn the unit on or off.
Always make sure the RESET button is pushed in for correct operation.
The power supply cord must be replaced if it fails to reset when either the TEST button is pushed,
or it cannot be reset. A new one can be obtained from the product manufacturer.
If power supply cord is damaged, it CANNOT be repaired. It MUST be replaced by one obtained
from the product manufacturer.
2009 Electrolux Home Products, Inc.
All rights reserved.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Product Registration, Packaging & Normal Sounds
Record Your Model and Serial Numbers
Product Registration
Record in the space provided below the model and serial numbers. On all models, the
serial plate is located on the outside of the cabinet.
Model No.
Serial No.
Register Your Product
The self-addressed PRODUCT REGISTRATION CARD should be filled in completely,
signed and returned to the Frigidaire Company.
Remove all packaging from inside the carton, along with any
inserts placed into the side louvers.
Packaging
PACKAGING
INSERTS
Normal Sounds
High pitched Chatter
Today’s high efficiency compressors
may have a high pitched chatter
during the cooling cycle.
Vibration
Unit may vibrate and make noise
because of poor wall or window
construction or incorrect installation.
Sound of Rushing Air
At the front of the unit, you may
hear the sound of rushing air
being moved by the fan.
Pinging or Swishing
Droplets of water hitting condenser
during normal operation may cause
“pinging or swishing” sounds.
Gurgle/Hiss
“Gurgling or hissing” noise may be heard
due to refrigerant passing through
evaporator during normal operation.
2009 Electrolux Home Products, Inc.
All rights reserved.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Instructions
To begin operating the air conditioner, follow these steps:
Using Air Conditioner
Operating Instructions
Set the temperature selector to the highest number (coldest or coolest setting).
Set the mode control to the highest COOL setting.
Adjust the louvers for comfortable air flow (see Air Directional Louvers).
Once the room has cooled, adjust the temperature selector to the setting you
find most comfortable.
Review the “Operating Instructions” section for other settings.
The controls featured in this manual are representative of many available
models. Your model may offer slightly different features.
Temperature Selector
This is used to set the desired room temperature when the unit is being
operated in the “COOL MODE”.
To set the desired room temperature, rotate the selector switch to the desired
setting. After the set temperature is achieved, the thermostat will automatically
start and stop the compressor in order to maintain the desired set temperature.
Rotate the temperature selector clockwise for higher cool setting. Higher cool
settings will provide lower room temperature.
Rotate the temperature selector counter-clockwise for lower cool settings.
Lower cool settings will provide higher room temperature.
Cool Mode
The desired cool setting is selected by rotating the MODE knob to the appropriate location.
“High Cool” has maximum cooling effect and airflow.
“
” between “High Cool” and “Low Cool” has the intermediate cooling effect and airflow.
“Low Cool” has minimum cooling effect and airflow.
Note:If your unit is equipped with a vent handle, keep it closed for maximum efficiency.
Fan Mode
Rotate the MODE knob to the left to select your choice of fan speeds for air circulation.
Note: When selecting a fan speed, the compressor will not run. On models with a vent
control, this mode can be used to remove stale air from the room, or to draw fresh air
into the room. Check the section ‘Additional Things You Should Know’.
WARNING
Please always wait 3 minutes when turning unit off then on again, and when changing from cool to fan and back to
cool. This prevents compressor from overheating & possible circuit breaker tripping.
Failure to follow these instructions may be harmful to your unit.
2009 Electrolux Home Products, Inc.
All rights reserved.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Instructions
Operating Instructions
(continued)
Air Directional Louvers
Air directional louvers control air flow direction. Your air conditioner has the louver
type described below.
(8-WAY)
AUGER WHEELS
Auger Type
The louvers will allow you to direct the air flow Up or Down and Left or Right
throughout the room as needed. Rotate the Auger Wheels until the desired
Left/Right direction is obtained. Pivot horizontal louvers until the desired
Up/Down direction is obtained.
ADDITIONAL THINGS YOU SHOULD KNOW
Now that you have mastered the operating procedure, here are more features that you should become familiar with.
Fresh Air Vent Control (on some models)
The Fresh Air Vent allows the air conditioner to:
1. Recirculate inside air - Vent Closed (see Fig. 1)
2. Draw fresh air into the room - Fresh Air (see Fig. 2)
3. Exchange air from the room - Vent Open (see Fig. 3)
Figure 1 (VENT CLOSED)
Figure 2 (FRESH AIR)
Figure 3 (VENT OPEN)
2009 Electrolux Home Products, Inc.
All rights reserved.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and Cleaning & Energy Saving Ideas
Clean your air conditioner occasionally to keep it looking new. Be sure to unplug
the unit before cleaning to prevent shock or fire hazards.
Care and Cleaning
Air Filter Cleaning
The air filter should be checked at least once a month to see if cleaning is
necessary. Trapped particles in the filter can build up and cause an accumulation
of frost on the cooling coils.
Push the vent handle to the Vent Closed position(where applicable).
Open the front panel.
Grasp the filter by the center and pull up and out.
Wash the filter using liquid dishwashing detergent and warm water. Rinse filter
thoroughly. Gently shake excess water from the filter. Be sure filter is
thoroughly dry before replacing
Or instead of washing, you may vacuum the filter clean.
Cabinet Cleaning
Be sure to unplug the air conditioner to prevent shock or fire hazard. The
cabinet and front may be dusted with an oil-free cloth or washed with a cloth
dampened in a solution of warm water and mild liquid dishwashing detergent.
Rinse thoroughly and wipe dry.
Never use harsh cleaners, wax or polish on the cabinet front.
Be sure to wring excess water from the cloth before wiping around the controls.
Excess water in or around the controls may cause damage to the air conditioner.
Plug in air conditioner.
Winter Storage
If you plan to store the air conditioner during the winter, remove it carefully from
the window according to the installation instructions. Cover it with plastic or return
it to the original carton.
Do not block air flow inside with blinds, curtains or furniture; or outside with
shrubs, enclosures, or other buildings.
Energy Saving Ideas
The capacity of the room air conditioner must fit the room size for efficient and
satisfactory operation.
Install the room air conditioner on the shady side of your home. A window that faces
north is best because it is shaded most of the day.
Close the fireplace damper, floor and wall registers so cool air does not escape up
the chimney and into the duct work.
Keep blinds and drapes in other windows closed during the sunniest part of the day.
Clean the air filter as recommended in the section “Care and Cleaning”.
Proper insulation and weather stripping in your home will help keep warm air out
and cool air in.
External house shading with trees, plants or awnings will help reduce the air
conditioner’s work load.
Operate heat producing appliances such as ranges, washers, dryers and dishwashers
during the coolest part of the day.
2009 Electrolux Home Products, Inc.
All rights reserved.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Before You Call
Before calling for service, review this list. It may save you time and expense. This list includes common occurrences that are not
the result of defective workmanship or materials in this appliance.
OCCURRENCE
SOLUTION
Wall plug disconnected. Push plug firmly into wall outlet.
Air conditioner will not operate.
Plug Current Device tripped. Press the RESET button.
House fuse blown or circuit breaker tripped. Replace fuse with time delay type or reset circuit breaker.
Selector Control in OFF position. Turn selector to ON (some models) or the desired FAN or COOL setting.
Unit turned off by moving thermostat to a higher number and then immediately turning back to a colder
number. Wait approximately 3 minutes. Listen for compressor to restart.
Unit turned off and then on too quickly. Turn unit off and wait 3 minutes before restarting.
Temperature selector set too low. Adjust temperature selector to higher number for cooling.
Turn selector to a higher COOL position.
Air from unit does not feel cold
enough.
Temperature selector set too warm. Set temperature selector to colder temperature.
Room temperature below 60O F (16O C). Cooling may not occur until room temperature rises above
60 OF (16O C).
Temperature sensing tube touching cold coil, located behind air filter. Straighten tube away from coil.
Outdoor temperature below 60 O F (16 OC). To defrost the coil, set selector to a FAN position. Then, set
thermostat to warmer position.
Air conditioner cooling, but
room is too warm - ice forming
on cooling coil behind decorative
front
Air filter may be dirty. Clean filter. Refer to Care and Cleaning section. To defrost, set selector to FAN.
Temperature selector set too cold for night-time cooling. To defrost the coil, set selector to a FAN
position. Then, set temperature selector to warmer position.
Dirty air filter - air restricted. Clean air filter. Refer to Care and Cleaning section.
Temperature selector set too warm. Turn temperature selector clockwise to a colder setting.
Air directional louvers positioned improperly. Position louvers for better air distribution.
Air conditioner cooling, but room
is too warm - NO ice forming on
cooling coil behind decorative
front.
Front of unit is blocked by drapes, blinds, furniture, etc. - restricts air distribution. Clear blockage in
front of unit.
Doors, windows, registers, etc. open - cool air escapes. Close doors, windows, registers, etc.
Unit recently turned on in hot room. Allow additional time to remove “stored heat” from walls, ceiling,
floor and furniture.
Dirty air filter - air restricted. Clean air filter.
Air conditioner turns on and off
rapidly.
Outside temperature extremely hot. Set to High Cool to bring air through cooling coils more frequently.
Noise when unit is cooling.
Air movement sound. This is normal. If too loud, turn selector to lower FAN setting.
Sound of fan hitting water-moisture removal system. This is normal when humidity is high. Close doors,
windows and registers.
Window vibration - poor installation. Refer to installation instructions or check with installer.
Improper installation. Tilt air conditioner slightly to the outside to allow water drainage. Refer to
installation instructions or check with installer.
Water dripping INSIDE when
unit is cooling.
Water dripping OUTSIDE when
unit is cooling.
Unit removing large quantity of moisture from humid room. This is normal during excessively humid
days.
Temperature selector set too high, set to a lower number on temperature dial.
Room too cold.
If These Solutions Fail, Call 1-800-944-9044 For Frigidaire Service.
2009 Electrolux Home Products, Inc.
All rights reserved.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Major Appliance Warranty
Your appliance is covered by a limited one-year warranty and a limited 2-5 year warranty on the sealed system (the compressor,
condenser, evaporator and tubing). For one year from your original date of purchase, Electrolux will pay all costs for repairing or
replacing any parts of this appliance that prove to be defective in materials or workmanship when such appliance is installed,
used and maintained in accordance with the provided instructions. From the second to the fifth year from your original purchase
date, Electrolux will repair or replace any parts in the Sealed Refrigeration System (compressor, condenser, evaporator and tubing)
that prove to be defective in materials or workmanship. In years 2-5, the consumer will be responsible for diagnostic, labor and
parts costs as well as any removal, transportation and reinstallation expenses which are incurred during service on components
other than those covered under the Sealed Refrigeration System 5-year warranty.
Exclusions
This warranty does not cover the following:
1. Products with original serial numbers that have been removed, altered or cannot be readily determined.
2. Product that has been transferred from its original owner to another party or removed outside the USA or
Canada.
3. Rust on the interior or exterior of the unit.
4. Products purchased "as-is" are not covered by this warranty.
5. Food loss due to any refrigerator or freezer failures.
6. Products used in a commercial setting.
7. Service calls which do not involve malfunction or defects in materials or workmanship, or for appliances not
in ordinary household use or used other than in accordance with the provided instructions.
8. Service calls to correct the installation of your appliance or to instruct you how to use your appliance.
9. Expenses for making the appliance accessible for servicing, such as removal of trim, cupboards, shelves,
etc., which are not a part of the appliance when it is shipped from the factory.
10. Service calls to repair or replace appliance light bulbs, air filters, water filters, other consumables, or knobs,
handles, or other cosmetic parts.
11. Surcharges including, but not limited to, any after hour, weekend, or holiday service calls, tolls, ferry trip
charges, or mileage expense for service calls to remote areas, including the state of Alaska.
12. Damages to the finish of appliance or home incurred during installation, including but not limited to floors,
cabinets, walls, etc.
13. Damages caused by: services performed by unauthorized service companies; use of parts other than
genuine Electrolux parts or parts obtained from persons other than authorized service companies; or external
causes such as abuse, misuse, inadequate power supply, accidents, fires, or acts of God.
DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES
CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR OR
REPLACEMENT AS PROVIDED HEREIN. CLAIMS BASED ON IMPLIED WARRANTIES, INCLUDING WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST
PERIOD ALLOWED BY LAW, BUT NOT LESS THAN ONE YEAR. ELECTROLUX SHALL NOT BE LIABLE FOR
CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND INCIDENTAL EXPENSES
RESULTING FROM ANY BREACH OF THIS WRITTEN LIMITED WARRANTY OR ANY IMPLIED WARRANTY. SOME
STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSE-
QUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES, SO THESE LIMITATIONS
OR EXCLUSIONS MAY NOT APPLY TO YOU. THIS WRITTEN WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS.
YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE.
If You Need Keep your receipt, delivery slip, or some other appropriate payment record to establish the warranty period
Service
should service be required. If service is performed, it is in your best interest to obtain and keep all receipts.
Service under this warranty must be obtained by contacting Electrolux at the addresses or phone
numbers below.
This warranty only applies in the USA and Canada. In the USA, your appliance is warranted by Electrolux Major Appliances North
America, a division of Electrolux Home Products, Inc. In Canada, your appliance is warranted by Electrolux Canada Corp.
Electrolux authorizes no person to change or add to any obligations under this warranty. Obligations for service and parts under
this warranty must be performed by Electrolux or an authorized service company. Product features or specifications as described
or illustrated are subject to change without notice.
USA
Canada
1.800.265.8352
Electrolux Canada Corp.
5855 Terry Fox Way
Mississauga, Ontario, Canada
L5V 3E4
1.800.944.9044
Electrolux Major Appliances
North America
P.O. Box 212378
Augusta, GA 30907
2009 Electrolux Home Products, Inc.
All rights reserved.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
|