All about the
Use&Care
of your
Room Air Conditioner
TABLE OF CONTENTS
Important Safety Instructions ............................... 2-3
Product Registration ............................................. 4
Normal Sounds .................................................... 4
Air Conditioner Features ....................................... 5
Operating Instructions .......................................... 5-10
.............................................. 10
Care and Cleaning
Energy Saving Ideas ........................................... 10
Before You Call ................................................... 11
Major Appliance Limited Warranty ........................ 12
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Instructions
SAFETY PRECAUTIONS
CAUTION! Avoid Injury or damage to the unit or other property
Provide occasional ventilation during use. Do not direct airflow at fireplaces or other heat related sources as this could cause flare ups or make
units run excessively.
Do not climb on or place objects on outdoor part of the unit.
Do not hang objects off the unit.
Do not place containers with liquids on the unit.
Turn off the air conditioner at the power source when it will not be used for an extended period of time.
Periodically check the condition of the unit’s installation accessories for any damage.
Do not apply heavy pressure to the radiator fins of the unit.
Operate the unit with air filter in place.
Do not block or cover the intake grille, discharge area and outlet ports.
Ensure that any electrical/electronic equipment is one yard away from the unit.
Do not use or store flammable gases near the unit.
READ THIS SECTION BEFORE ATTEMPTING TO OPERATE AIR CONDITIONER.
Unit must be upright for one hour prior to operating.
The power supply cord contains a current device that senses damage to the power cord. To test
your power supply cord do the following:
Plug in the Air Conditioner.
The power supply cord will have TWO buttons on the plug head. Press the TEST button. You will
notice a click as the RESET button pops out.
Plug in &
Press the RESET button. Again you will notice a click as the button engages.
press RESET
The power supply cord is now supplying electricity to the unit.
NOTE:
Do not use this device to turn the unit on or off.
Always make sure the RESET button is pushed in for correct operation.
The power supply cord must be replaced if it fails to reset when either the TEST button is pushed,
or it cannot be reset. A new one can be obtained from the product manufacturer.
If power supply cord is damaged, it CANNOT be repaired. It MUST be replaced by one obtained
from the product manufacturer.
2009 Electrolux Home Products, Inc.
All rights reserved.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Product Registration & Normal Sounds
Record Your Model and Serial Numbers
Product Registration
Record in the space provided below the model and serial numbers. On all models, the
serial plate is located on the outside of the cabinet.
Model No.
Serial No.
Register Your Product
The self-addressed PRODUCT REGISTRATION CARD should be filled in completely,
signed and returned to the Frigidaire Company.
Normal Sounds
High pitched Chatter
Today’s high efficiency compressors
may have a high pitched chatter
during the cooling cycle.
Vibration
Unit may vibrate and make noise
because of poor wall or window
construction or incorrect installation.
Sound of Rushing Air
At the front of the unit, you may
hear the sound of rushing air
being moved by the fan.
Pinging or Swishing
Droplets of water hitting condenser
during normal operation may cause
“pinging or swishing” sounds.
Gurgle/Hiss
“Gurgling or hissing” noise may be heard
due to refrigerant passing through
evaporator during normal operation.
2009 Electrolux Home Products, Inc.
All rights reserved.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Air Conditioner Features & Operating Instructions
ELECTRONIC CONTROL
Before you begin, thoroughly familiarize yourself with the control panel and remote
as shown below and all its functions, then follow the symbol for the functions you
desire. The unit can be controlled by the touch pad alone or with the remote.
Air Conditioner Features
ADJUSTS
TEMPERATURE
OR TIME
DISPLAYS
TEMPERATURE/TIME
SLEEP MODE
CHECK FILTER
RESET BUTTON
SETS FAN
SPEED
REMOTE TEMP
SENSING INDICATOR
(some models)
TURNS UNIT
ON OR OFF
SETS MODE
ACTIVATES TIMER
Battery Size: AAA
Warning: Do not mix old and new batteries. Do not mix alkaline, standard
(carbon-zinc), or rechargeable (nickel-cadmium) batteries.
w/DISPLAY &
FOR HEAT MODELS
REMOTE SENSING
BUTTON
Operating Instructions
NOTE
The following instructions represent the Touch Pad, the same instructions can be used for the Remote Control.
TO TURN UNIT ON:
YOU WILL SEE:
DO THIS:
PRESS ON/OFF
BUTTON
2009 Electrolux Home Products, Inc.
All rights reserved.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Instructions
Operating Instructions
TO CHANGE TEMPERATURE SETTlNG:
YOU WILL SEE:
DO THIS:
PRESS
PRESS
TO RAISE
TO LOWER
Note: Tap or hold either up (
) or down (
) button until the desired temperature is seen on the display. This temperature will
be automatically maintained anywhere between 60 °F (16 °C) and 90 °F (32 °C) for cooling mode. The temperature will be auto-
matically maintained anywhere between 55 °F (13 °C) and 80 °F (27 °C) for heating mode. If you want the display to read the
actual room temperature. See "To Operate on Fan Only" section on this page.
TO ADJUST FAN SPEEDS:
YOU WILL SEE:
DO THIS:
PRESS TO SELECT
TO USE AUTO FAN FEATURE:
YOU WILL SEE:
DO THIS:
PRESS FAN
BUTTON
SELECT AUTO
Note: Fan starts at High Speed and adjusts to a slower speed as the room temperature dictates. For example, if the room doesn't
get too warm, it will stay at the slowest speed. If the room temperature rises quickly, such as a door being opened, it will auto-
matically go to the highest speed. The fan speeds will re-adjust back to the slowest speed as the room returns to the original set
temperature. Press either the fan slower or fan faster button to adjust the fan speed manually. This function is deactivated in the
heating mode on 115V models.
TO OPERATE ON FAN ONLY:
YOU WILL SEE:
DO THIS:
PRESS
MODE BUTTON
CHOOSE
FAN ONLY
Note: Use this function only when cooling is not desired, such as for room air circulation or to exhaust stale air on some models.
(Remember to open the vent during this function, but keep it closed during cooling for maximum cooling efficiency.) You can
choose any fan speed you prefer. (Except “Auto Fan”).
During this function, the display will show the actual room temperature, not the set temperature as in the cooling mode. Fan Only
cannot be selected when the unit is in the “Remote Sensing” mode. (on those units with that feature).
2009 Electrolux Home Products, Inc.
All rights reserved.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Instructions
Operating Instructions
(continued)
TO USE THE ENERGY SAVER
FEATURE:
YOU WILL SEE:
DO THIS:
PRESS
MODE BUTTON
CHOOSE
ENERGY SAVER
Note: In this mode, the fan will continue to run for 1 minute after the compressor shuts off. The fan then cycles on for 20 seconds
at 10 minute intervals until the room temperature is above the set temperature, at which time the compressor turns back on.
TIMER: DELAY STOP / START
FEATURE
YOU WILL SEE HOW MUCH TIME
IS CHOSEN:
THEN
FIRST
DO THIS:
DO THIS:
PRESS
UP/DOWN
SET BUTTONS
PRESS
TIMER BUTTON
Note: For Delay Stop, the unit must be in the On position.
Note: For Delay Start, the unit must be in the Off position.
First, Press TIMER button, then adjust timer setting, tap or hold the UP arrow (
) or the DOWN arrow (
) to change delay
timer at 0.5 hour increments, up to 10 hours, then at 1 hour increments up to 24 hours. The control will count down the time
remaining until start (8, 7.5, 7, etc.). The Delay Start Operation automatically selects cooling with maximum Fan speed (if Cool,
Energy Saver, or Fan Only was the last mode selected) or heating with maximum Fan speed (if Heat was the last mode selected.
Note: On 115V models only low speed can be selected.) The temperature maintained will be the same as previously set. To change
the set temperature, press "COOL" then Up or Down arrows until the desired temperature is indicated on the display. After 5
seconds, the control will automatically change the display back to the hours remaining until the unit will start/stop. Pressing the
unit On/Off button at any time will cancel the Delay Start/Stop function. The Delay Start/Stop Feature will work until the unit either
starts or stops. Once that happens the above steps have to be repeated again.
SLEEP FEATURE:
YOU WILL SEE:
DO THIS:
PRESS
SLEEP BUTTON
Note: In this mode the selected temperature will increase by 2 °F 30 minutes after the mode is selected. The temperature will then
increase by another 2 °F after an additional 30 minutes. This new temperature will be maintained for 7 hours before it returns to
the originally selected temperature. This ends the "Sleep" mode and the unit will continue to operate as originally programmed.
The "Sleep" mode program can be cancelled at any time during operation by again pressing the "Sleep" button.
2009 Electrolux Home Products, Inc.
All rights reserved.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Instructions
Operating Instructions
(continued)
CHECK FILTER FEATURE:
YOU WILL SEE:
DO THIS:
PRESS FILTER
RESET BUTTON
Note: This feature is a reminder to clean the Air Filter (See Care and Cleaning) for more efficient operation. The LED (light) Will
illuminate after 250 hours of operation. To reset after cleaning the filter, press the "Filter Reset" button and the light will go off.
REMOTE SENSING FEATURE
(on some models)：
LIGHT pulsing ( On & Off intermittently ).
DO THIS:
PRESS REMOTE
SENSING
START BUTTON
NOTE: Unit display shows the set temperature
NOTE: Remote display
is actual temperature
at remote control only
Note: This feature can be activated from the remote control ONLY, the unit must be in a cooling mode.
To activate the remote sensing feature, point the remote control towards the unit and press the remote sensing Start button. Next, use
the “ ” buttons to set the desired temperature at the remote. (Note that the set temperature will only be displayed on the unit
itself ). The LIGHT on the unit control will pulse to indicate it received the signal. The LIGHT on the remote control will pulse each time it
sends a signal. lt will periodically send this signal until the feature is deactivated by pressing the remote sensing Stop button. lf the unit
does not receive the remote sensing signal during any 3 minute interval, the unit will beep to indicate the remote sensing mode has
ended. The display on the remote control indicates the temperature at the remote ONLY.
NOTE: The Remote Sensing function is terminated either by using the Remote Sensing Stop button or the main ON/OFF button on the
unit.
HEATING FEATURE(on some models)：
YOU WILL SEE:
DO THIS:
PRESS
MODE BUTTON
SELECT HEAT
Note: This feature can be used with any combination of FAN Speeds (Low speed only on 115V models), Timer, or Sleep Modes. When in
the "Heat" mode,the fan will run continuously while heat is needed. The temperature will automatically be maintained anywhere between
55 °F(13 °C) and 80 °F(27 °C). When the room set temperature is satisfied, the fan will cycle off and on to circulate and sample the room
air.
2009 Electrolux Home Products, Inc.
All rights reserved.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Instructions
Operating Instructions
(continued)
FAULT CODES:
If the display reads "HS" , a sensor has
failed. Contact your Authorized Frigidaire
Service Center.
If the display reads "AS" , a sensor has
failed. Contact your Authorized Frigidaire
Service Center.
If the display reads "ES" , a sensor has
failed. Contact your Authorized Frigidaire
Service Center.
YOU WILL SEE:
TO CHANGE TEMPERATURE DISPLAY:
DO THIS:
PRESS AND HOLD THE
UP/DOWN BUTTONS
TOGETHER FOR 3 SECONDS
Note: The control is capable of displaying temperature in degrees Fahrenheit or degrees Celsius.
TO TURN UNIT OFF:
YOU WILL SEE:
DO THIS:
PRESS
ON/OFF BUTTON
Note: When unit is shut off in the Heat Mode, the fan will continue to run for a few seconds to dissipate residual heat within the unit.
ADDITIONAL THINGS YOU SHOULD KNOW
Now that you have mastered the operating procedure, here are more features in your control that you should become familiar with.
The "Cool" circuit has an automatic 3 minute time delayed start if the unit is turned off and on quickly.
This prevents overheating of the compressor and possible circuit breaker tripping. The fan will continue
to run during this time.
There is a 2-Second delay for the compressor shutting down when selecting FAN ONLY/HEAT. This is to cover the possibility of
having to roll through to select another mode.
The control will maintain the set temperature within 2 degrees Fahrenheit, between 60F and 90F degrees (in cool mode), 55F
and 80F degrees (in heat mode).
After a power outage, the unit will memorize the last setting and return the unit to the same setting once power is restored.
2009 Electrolux Home Products, Inc.
All rights reserved.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Instructions & Care and Cleaning & Energy Saving Ideas
Operating Instructions
(continued)
4-Way Air Directional Louvers
The 4-Way air directional louvers allow you to direct the air flow Up or Down
and Left or Right throughout the room as needed. To adjust the air direc-
tional louvers side-to-side, use the center handle as you move it side-to-side.
(4-WAY)
Clean your air conditioner occasionally to keep it looking new. Be sure to unplug
the unit before cleaning to prevent shock or fire hazards.
Care and Cleaning
Air Filter Cleaning
The air filter should be checked at least once a month to see if cleaning is
necessary. Trapped particles in the filter can build up and cause an accumulation
of frost on the cooling coils.
Grasp the filter by the center and pull up and out.
Wash the filter using liquid dishwashing detergent and warm water. Rinse filter
thoroughly. Gently shake excess water from the filter. Be sure filter is
thoroughly dry before replacing
Or instead of washing, you may vacuum the filter clean.
Cabinet Cleaning
Be sure to unplug the air conditioner to prevent shock or fire hazard. The
cabinet and front may be dusted with an oil-free cloth or washed with a cloth
dampened in a solution of warm water and mild liquid dishwashing detergent.
Rinse thoroughly and wipe dry.
Never use harsh cleaners, wax or polish on the cabinet front.
Be sure to wring excess water from the cloth before wiping around the controls.
Excess water in or around the controls may cause damage to the air conditioner.
Plug in air conditioner.
Winter Storage
If you plan to store the air conditioner during the winter, remove it carefully from
the window according to the installation instructions. Cover it with plastic or return
it to the original carton.
NOTE: To prevent rust or electrical connections from being damaged, store air
conditioner in an upright position and a dry place.
Do not block air flow inside with blinds, curtains or furniture; or outside with
shrubs, enclosures, or other buildings.
Energy Saving Ideas
The capacity of the room air conditioner must fit the room size for efficient and
satisfactory operation.
Install the room air conditioner on the shady side of your home. A window that faces
north is best because it is shaded most of the day.
Close the fireplace damper, floor and wall registers so cool air does not escape up
the chimney and into the duct work.
Keep blinds and drapes in other windows closed during the sunniest part of the day.
Clean the air filter as recommended in the section “Care and Cleaning”.
Proper insulation and weather stripping in your home will help keep warm air out
and cool air in.
External house shading with trees, plants or awnings will help reduce the air
conditioner’s work load.
Operate heat producing appliances such as ranges, washers, dryers and dishwashers
during the coolest part of the day.
2009 Electrolux Home Products, Inc.
All rights reserved.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Before You Call
Before calling for service, review this list. It may save you time and expense. This list includes common occurrences that are not
the result of defective workmanship or materials in this appliance.
OCCURRENCE
SOLUTION
Wall plug disconnected. Push plug firmly into wall outlet.
Air conditioner will not operate.
Plug Current Device Tripped. Press the RESET button.
House fuse blown or circuit breaker tripped. Replace fuse with time delay type or reset circuit breaker.
Control is OFF. Turn Control ON and set to desired setting.
Room temperature below 60°F (16°C). Cooling may not occur until room temperature rises above
60°F (16°C).
Air from unit does not feel cold
enough.
Temperature sensing element touching cold coil, located behind air filter. Straighten away from coil.
Reset to a lower temperature.
Compressor shut-off by changing modes. Wait approximately 3 minutes and listen for compressor to
restart when set in the COOL mode.
Outdoor temperature below 60 O F (16 OC). To defrost the coil, set FAN ONLY mode.
Air conditioner cooling, but room
is too warm - ice forming
on cooling coil behind decorative
front
Air filter may be dirty. Clean filter. Refer to Care and Cleaning section. To defrost, set to FAN ONLY
mode.
Temperature is set too low for night-time cooling. To defrost the coil, set to FAN ONLY mode. Then,
set temperature to a higher setting.
Dirty air filter - air restricted. Clean air filter. Refer to Care and Cleaning section.
Temperature is set too high. Set temperature to a lower setting.
Air conditioner cooling, but room
is too warm - NO ice forming on
cooling coil behind decorative
front.
Air directional louvers positioned improperly. Position louvers for better air distribution.
Front of unit is blocked by drapes, blinds, furniture, etc. - restricts air distribution. Clear blockage in
front of unit.
Doors, windows, registers, etc. open - cool air escapes. Close doors, windows, registers, etc.
Unit recently turned on in hot room. Allow additional time to remove “stored heat” from walls, ceiling,
floor and furniture.
Dirty air filter - air restricted. Clean air filter.
Air conditioner turns on and off
rapidly.
Outside temperature extremely hot. Set FAN speed to a faster setting to bring air through cooling coils
more frequently.
Air movement sound. This is normal. If too loud, set to lower FAN setting.
Noise when unit is cooling.
Sound of fan hitting water-moisture removal system. This is normal when humidity is high. Close
doors, windows and registers.
Window vibration - poor installation. Refer to installation instructions or check with installer.
Improper installation. Tilt air conditioner slightly to the outside to allow water drainage. Refer to
installation instructions or check with installer.
Water dripping INSIDE when
unit is cooling.
Water dripping OUTSIDE when
unit is cooling.
Unit removing large quantity of moisture from humid room. This is normal during excessively humid
days.
Remote control not located within range. Place remote control within 20 feet & 120° radius of the
front of the unit．
Remote Sensing Deactivating
Prematurely (some models).
Remote control signal obstructed. Remove obstruction.
Set temperature too low. lncrease set temperature.
Room too cold.
Remote Sensing activated (on some models) and remote control located in Hot Spot - Relocate remote
control or deactivate remote sensing.
If These Solutions Fail, Call 1-800-944-9044 For Frigidaire Service.
2009 Electrolux Home Products, Inc.
All rights reserved.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Major Appliance Limited Warranty
Your appliance is covered by a limited two-year warranty and a limited 3-5 year warranty on the sealed system (the compressor,
condenser, evaporator and tubing). For two years from your original date of purchase, Electrolux will pay all costs for repairing or
replacing any parts of this appliance that prove to be defective in materials or workmanship when such appliance is installed,
used and maintained in accordance with the provided instructions. From the third to the fifth year from your original purchase
date, Electrolux will repair or replace any parts in the Sealed Refrigeration System (compressor, condenser, evaporator and tubing)
that prove to be defective in materials or workmanship. In years 3-5, the consumer will be responsible for diagnostic, labor and
parts costs as well as any removal, transportation and reinstallation expenses which are incurred during service on components
other than those covered under the Sealed Refrigeration System 5-year warranty.
Exclusions
This warranty does not cover the following:
1. Products with original serial numbers that have been removed, altered or cannot be readily determined.
2. Product that has been transferred from its original owner to another party or removed outside the USA or
Canada.
3. Rust on the interior or exterior of the unit.
4. Products purchased "as-is" are not covered by this warranty.
5. Food loss due to any refrigerator or freezer failures.
6. Products used in a commercial setting.
7. Service calls which do not involve malfunction or defects in materials or workmanship, or for appliances not
in ordinary household use or used other than in accordance with the provided instructions.
8. Service calls to correct the installation of your appliance or to instruct you how to use your appliance.
9. Expenses for making the appliance accessible for servicing, such as removal of trim, cupboards, shelves,
etc., which are not a part of the appliance when it is shipped from the factory.
10. Service calls to repair or replace appliance light bulbs, air filters, water filters, other consumables, or knobs,
handles, or other cosmetic parts.
11. Surcharges including, but not limited to, any after hour, weekend, or holiday service calls, tolls, ferry trip
charges, or mileage expense for service calls to remote areas, including the state of Alaska.
12. Damages to the finish of appliance or home incurred during installation, including but not limited to floors,
cabinets, walls, etc.
13. Damages caused by: services performed by unauthorized service companies; use of parts other than
genuine Electrolux parts or parts obtained from persons other than authorized service companies; or external
causes such as abuse, misuse, inadequate power supply, accidents, fires, or acts of God.
DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES
CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR OR
REPLACEMENT AS PROVIDED HEREIN. CLAIMS BASED ON IMPLIED WARRANTIES, INCLUDING WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST
PERIOD ALLOWED BY LAW, BUT NOT LESS THAN ONE YEAR. ELECTROLUX SHALL NOT BE LIABLE FOR
CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND INCIDENTAL EXPENSES
RESULTING FROM ANY BREACH OF THIS WRITTEN LIMITED WARRANTY OR ANY IMPLIED WARRANTY. SOME
STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSE-
QUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES, SO THESE LIMITATIONS
OR EXCLUSIONS MAY NOT APPLY TO YOU. THIS WRITTEN WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS.
YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE.
If You Need Keep your receipt, delivery slip, or some other appropriate payment record to establish the warranty period
Service
should service be required. If service is performed, it is in your best interest to obtain and keep all receipts.
Service under this warranty must be obtained by contacting Electrolux at the addresses or phone
numbers below.
This limited warranty only applies in the USA and Canada. In the USA, your appliance is warranted by Electrolux Major Appliances
North America, a division of Electrolux Home Products, Inc. In Canada, your appliance is warranted by Electrolux Canada Corp.
Electrolux authorizes no person to change or add to any obligations under this warranty. Obligations for service and parts under
this warranty must be performed by Electrolux or an authorized service company. Product features or specifications as described
or illustrated are subject to change without notice.
USA
Canada
1.800.265.8352
Electrolux Canada Corp.
5855 Terry Fox Way
Mississauga, Ontario, Canada
L5V 3E4
1.800.944.9044
Electrolux Major Appliances
North America
P.O. Box 212378
Augusta, GA 30907
2009 Electrolux Home Products, Inc.
All rights reserved.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
|