e x e r c i s e
s y s t e m
O W N E R ’ S M A N U A L
Download from Www.Somanuals.com. All Manuals Search And Download.
PRODUCT SPECIFICATIONS
Hitch Pins (5)—
Height
Adjustment
“C” Pin
2 small safety hitch pins located in
the base of the right and left rails on
the column end of the exercise unit.
Vertical Height
Adjustment Column
2 small
3 large
3 large hitch pins located in the leg
pulley accessory kit.
Arm Pulley
Assembly
Height
Adjustment
Lever
Glideboard
Cable
Front Crossbar
Handle
Top Inner Rail
Center Support Rail
Back Crossbar
Rollers
Bottom Outer Rail
Leg Pulley Accessory Kit
2 Large
Hitch
Pins
Wing Attachment
Pulley/D-Ring
Assembly
1 Large
Hitch Pin
Rope
Foot
Harness
Foam
Pad
O-ring
Brackets
Clip
LENGTH:
folded 501/2”
in use 88”
Leg Pulley Bracket
For use with leg pulley
accessory only.
HEIGHT:
folded 81/2”
in use 44”
Allen
Wrenches
WIDTH:
161/8”
WEIGHT:
58 lbs.
Stopper
MAX. USER WEIGHT:
275 lbs.
Packed in the leg pulley
accessory kit
— 4 —
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
WARNING
FAILURE TO READ AND FOLLOW THE SAFETY INSTRUCTIONS IN THIS MANUAL
MAY RESULT IN SERIOUS INJURY.
Before beginning this or any exercise program, consult a physician or health profes-
sional, who can assist you in planning a program appropriate for your age and physical con-
dition. This is especially important if you are over age 35 or have pre-existing health prob-
lems.
Do not overexert yourself. Stop exercising immediately and consult your doctor if you expe-
rience pain or tightness in your chest, irregular heart beat, shortness of breath, or if you feel
faint, nauseous, or dizzy.
This product is designed for home use only. It is not intended for commercial or institu-
tional use. Use only as instructed. Do not stand on the product.
Adult supervision is required at all times.
Keep fingers, loose clothing, and hair away from moving parts.
Inspect your exerciser before each use to ensure proper operation. Do not use this
equipment unless all moving parts are working properly.
The exerciser should be used on carpeted surfaces only.
Use only the accessory items recommended by the manufacturer.
To avoid serious injury, care should be taken at all times when getting on and off this or any
exercise equipment.
— 5 —
Download from Www.Somanuals.com. All Manuals Search And Download.
SET UP
W
A
R
NI
N
G
KEEP HAIR, FINGERS, LOOSE CLOTHING, PETS, AND CHILDREN AWAY FROM HINGES
AND OTHER MOVING PARTS TO AVOID SERIOUS INJURY. ALSO, TO AVOID SERIOUS
INJURY, BE SURE TO HAVE THE HEIGHT ADJUSTMENT “C” PIN AND HITCH PINS AT
BASE OF RAILS LOCKED IN PLACE BEFORE GETTING ON YOUR TOTAL GYM 1000.
1.
Pull the product out of the shipping box. Remove all packaging materials, including
tape and cardboard inserts, from your Total Gym® 1000. Hitch Pin Location:
Three (3) large pins in the leg pulley accessory kit and two small safety pins
locked into base of right and left rails to prevent height adjustment column
from falling forward.
2.
Lay product flat on the floor. Remove the wing accessory
from its packaging. Make sure you have plenty of space
3.
on both ends of the product. Slide the glideboard all the
way towards the front crossbar.
3.
4.
Raise the exerciser up and spread the unit open
approximately 12 inches so that it rests firmly on
the front and back crossbars.
Back
Crossbar
Front
Crossbar
12”
4.
Place one hand on the edge of the
frame and begin to pull it out slowly
until the frame is lying flat on the floor.
Be sure to support the frame in the
center to avoid having the product
drop suddenly onto the floor.
5a
5.
(a) Remove the 2 small safety hitch pins
located in the brackets at the end of the
right and left rails.
5b
(b) Take hold of the vertical height
adjustment column and pull it up until
it is upright.
5c.
IMPORTANT
(c) Re-insert the 2 small safety hitch pins
through the brackets at the end of the right
and left rails.
— 6 —
Download from Www.Somanuals.com. All Manuals Search And Download.
6.
(a) Position one foot on back crossbar to keep
the product from lifting off the floor. With one
hand on either the right or left rail and the other
hand holding the height adjustment “C” pin,
slide the rails up along the height adjustment
column. Line up the hole to the first (lowest)
position on the height adjustment column.
6a.
6b.
(b) Insert height adjustment “C” pin
from the back as shown.
7.
7.
Push the pin down into its locked position (it should lay
flat against the height adjustment column).
Never sit on or exercise on the Total Gym® 1000
with out the height adjustment “C” pin securely
locked into place.
WARNING
FAILURE TO SECURELY LOCK THE HEIGHT ADJUSTMENT “C” PIN INTO
PLACE MAY RESULT IN SERIOUS INJURY.
NOTE: The rails and glideboard can be raised to any desired level on the height adjustment
column depending upon your degree of fitness. Please note, however, that the rails cannot be
raised to the highest position on the height adjustment column when the leg pulley bracket is
attached to the column. See page 10 for instructions on how to install the leg pulley bracket.
Be sure you have plenty of free space around the exerciser so that performing on the Total
Gym® 1000, as well as getting on and off, is convenient and safe.
Begin using the Total Gym® 1000 at a low incline. As your fitness level increases, raise
the incline to increase the intensity of your workout and improve your muscle strength.
Each time you raise or lower the adjustment column, be sure you hold it to keep it from
dropping to the floor.
— 7 —
Download from Www.Somanuals.com. All Manuals Search And Download.
WING ACCESSORY
The wing accessory provided with your unit has been uniquely designed to serve several pur-
poses. It can be placed at the top or bottom of the exerciser and angled toward you or away
from you depending upon what is comfortable for you.
Two thick foam pads are provided with the wing accessory. They must be attached to the
wing (if not already) before exercising. To do this:
1.
Simply wet each end of the straight crossbar of the wing with some soapy water.
Fig. 1
2.
Then, attach foam pads on the cross bar as shown
in Figure 1. Let dry before beginning to exercise
with the wing accessory.
Proper ways to use the wing accessory in accordance with
the exercises you wish to do:
PULL UPS
1.
Locate the holes at the top of the right and left rails on the column end of the unit.
2.
With the wing angled toward the glideboard, line up the brackets on the wing with the
desired position holes on the rails.
Fig. 2
3.
4.
Insert the 2 large hitch pins through the holes on the
wing accessory brackets and the hole on the rails, as
shown in Figure 2.
You are now ready to perform pull up and chin up exercises
to work the arms, lats and back. See your Exercise Booklet
for specific exercises.
LEG PULL: CRUNCHES, LEGS AND SIT UPS
1.
Locate the holes at the top of the right and left rails on the
column end of the unit.
2.
With the wing angled away from the glideboard, line up the
brackets on the wing with the desired position holes on the
rails.
Fig. 3
3.
4.
Insert the 2 large hitch pins through the holes on the
wing accessory brackets and the hole on the rails,
as shown in Figure 3.
You are now ready to perform leg pulls, crunches and sit up
exercises to work the abdominals, waist and legs. See your
Exercise Booklet for specific exercises.
— 8 —
Download from Www.Somanuals.com. All Manuals Search And Download.
FRONT PRESS
1.
Locate the holes at the bottom of the right and left rails near
the front crossbar.
Fig. 4
2.
With the wing angled toward the glideboard, line up the
brackets on the wing with the desired position holes on
the rails.
3.
4.
Insert the 2 large hitch pins through the holes on the wing
accessory brackets and the hole on the rails, as shown
in Figure 4.
You are now ready to perform the front press which works the
upper chest and triceps. See your Exercise Booklet for specific exercises.
SQUATS
1.
Locate the holes at the bottom of the right and left rails
near the front crossbar.
Fig. 5
2.
With the wing angled away from the glideboard, line up
the brackets on the wing with the desired position holes
on the rails.
3.
4.
Insert the 2 large hitch pins through the holes on the wing
accessory brackets and the hole on the rails, as shown
in Figure 5.
You are now ready to perform the front press which works the thighs and calves.
See your Exercise Booklet for specific exercises.
NOTE: When performing the squat exercises, be sure to position your hands
on the side of the glideboard, NOT along the bottom of the board in order to avoid
pinched fingers.
Download from Www.Somanuals.com. All Manuals Search And Download.
— 9 —
HOW TO ATTACH THE LEG PULLEY ACCESSORY KIT
Leg Pulley Accessory Kit
Pulley/D-Ring
Assembly
O-ring
Rope
Harness
Hitch
Pin
Leg Pulley Bracket
For use with leg pulley
Clip
accessory only.
1.
Connect the leg pulley bracket to the height adjustment column by
aligning bracket with the hole at the top of the column. (Be sure
1.
bracket is right side up.) Insert large hitch pin through the hole to
secure bracket onto the height adjustment column.
2.
3.
4.
Detach the arm pulley mechanism from the hook on the
underside of the glideboard.
Connect the O-ring (the one that is connected to the leg pulley
rope) to the hook on the underside of the glideboard.
Next, connect the D-ring/pulley combination of your leg pulley
accessory kit to the leg pulley bracket on the height adjustment
4.
column. If rope appears to be twisted, take “D” ring off and turn
pulley around.
5.
5.
6.
Attach the foot harness to one of your feet by placing your
O-Ring (loose)
foot in the harness so the sewn-in-ring is on the bottom of
your foot. Pull tightly on the belt so the harness is secure.
(a) Position yourself on the glideboard correctly for the
Harness
Buckle
Foot Harness
specific exercise you want to perform. See your
Exercise Booklet for specific exercises that utilize the
O-ring (sewn in)
leg pulley accessory.
(b) While lying down on the glideboard, connect the clip on the
6b.
Clip
end of the rope to an O-ring on the harness attached to
your foot. Depending on the exercise you are performing,
connect the clip to the proper O-ring. Be sure to always
stabilize the glideboard when clipping the harness on or off.
Also, use caution when getting on or off the glideboard. You
are now ready to exercise using the leg pulley accessory.
O-Ring (loose)
(c) To disconnect the harness, unclip the rope from the O-ring on
the harness while lying down on the glideboard. Be sure to
stabilize glideboard when disconnecting foot harness.
WARNING
OPERATE LEG PULLEY WITH CAUTION TO AVOID CONTACT WITH LEG PULLEY BRACKET
— 10 —
Download from Www.Somanuals.com. All Manuals Search And Download.
STARTING OUT
Wear athletic shoes and comfortable light clothing when exercising on the Total Gym® 1000.
Do not exercise barefoot. Check your exerciser before using to ensure that all the parts are in
place and working properly (see page 12 for details of the inspection process). Adult super-
vision is required at all times.
Begin using the product at a low incline. As your fitness level progresses, increase the incline
to increase the intensity and improve your muscle strength. Don’t be in a hurry to exercise at
a high intensity level; start out easily and build gradually. The Total Gym® 1000 is as easy as
1-2-3 to use, so read on.
1.
Important Things to Remember When Using the Total Gym®1000
• Always have control of the glideboard before getting on and off the exerciser.
• Keep your feet on the floor when getting on and off the exerciser. Only remove them
from the floor for the duration of the exercise.
• If you are using the handles, hold onto them as you get on and off the glideboard.
2.
Exercising with the Handles Only
Grasp the handles which are attached to the cable and slide the glideboard to a posi-
tion in which you can comfortably sit or lay down on when performing the desired exer-
cise (see the Exercise Booklet). Be sure to keep your feet on the floor until you are in
the correct position for the specific exercise. Then, if the exercise calls for your feet to
be off the floor, place your feet as specified in the instructions.
3.
Exercising with the Wing Accessory Only
Slide the glideboard to a position in which you can comfortably sit or lay down on
when performing the desired exercise (see the Exercise Booklet). Keep your feet on
the ground until you are in the correct position and feel comfortable. Then, place your
feet in the proper position and begin to exercise.
When starting your exercise program, begin with the basic exercises in the Exercise Booklet
included with your Total Gym® 1000 to familiarize yourself with the movements. Use the low-
est incline level to start with—you can work up to a higher incline level in the weeks and
months to come.
For the specific Total Gym® 1000 exercises and programs, study and follow the instruc-
tions in the Exercise Booklet included with your product.
— 11 —
Download from Www.Somanuals.com. All Manuals Search And Download.
INSPECTION AND MAINTENANCE
INSPECT YOUR TOTAL GYM 1000 PRIOR TO EACH USE
®
Before using your Total Gym® 1000 for your workout session, be sure to make the
following inspection:
•
•
•
Make sure the equipment is fully opened and sitting on a solid level surface with plenty
of clearance on all sides. Unit should be used on carpeted surfaces only.
Make sure all the hitch pins and the height adjustment “C” pin are securely in place
and locked into position.
Check that the pulley is attached securely to the hook on the front underside of the
glideboard.
•
•
•
•
Check that the cables are traveling correctly in the groove of each pulley.
Make sure the cable is securely fastened to each hand grip.
Check that the wing accessory is installed correctly when in use.
Make sure the glideboard is gliding smoothly along the frame.
ROUTINE MAINTENANCE
•
Wipe down your Total Gym® 1000 on a regular basis using a clean cloth and alcohol or
alcohol-based products like Windex® or 409®. Do not leave towels or workout clothing
laying or hanging on the equipment.
•
Periodically check the following parts for signs of fraying or other wear: the cable, the
pulleys, the wheels, the glideboard, the wing accessory and the frame. If a part needs
to be replaced, do not use the equipment until it is repaired.
•
Never use a lubricant such as WD-40® or ArmorAll® to lubricate or clean the unit. Use
only 3-in-1® oil or machine oil to lubricate the axles of the wheel or pulley, not the roller
surface.
TO STORE YOUR TOTALGYM® 1000
Follow these easy steps to store your Total Gym® 1000 properly:
1.
2.
3.
First, remove the wing accessory and leg pulley accessory.
Be sure the arm pulley cable is attached to the underside of the glideboard for folding.
Position one foot on back crossbar to keep the product from lifting off the floor. With
one hand on the rail, grasp the height adjustment “C” pin and pull it out from the height
adjustment column. Slowly lower the rails until they rest on the back crossbar.
Next, lower the height adjustment column all the way down until it rests on the center
rail.
4.
— 12 —
Download from Www.Somanuals.com. All Manuals Search And Download.
5a.
5.
(a) Remove the 2 small safety hitch pins
located in the brackets at the base of the
right and left rails on the column end
of the unit.
5b.
(b) Fold down vertical height adjustment
column and replace pins.
6.
6.
7.
With caution, to avoid pinched
fingers or hands, lift up at the center
of the frame and fold the exerciser
together until it rests firmly on the front
and back crossbars about 12 inches apart.
Back
Crossbar
Front
Crossbar
Continue to fold the exerciser together
until it is completely folded and roll the
12”
exerciser into a closet for storage. To store
under a bed, simply lower the exerciser to the floor and roll under the bed.
CAUTION
USE CAUTION WHEN FOLDING THE EXERCISER.
TO REMOVE THE GLIDEBOARD
You can also remove the glideboard if you need to fit the exerciser under a narrow space
(between 6” and 8”).
CAUTION
THE GLIDEBOARD WEIGHS APPROXIMATELY 15 LBS. USE CAUTION WHEN
LIFTING IT OFF OF THE EXERCISER. LIFTING INCORRECTLY MAY RESULT IN
USER INJURY.
1.
With exerciser laying flat on the floor, disconnect the pulley from the hook on the
underside of the glideboard. (The 2 small safety hitch pins should be securely
fastened through the brackets at the base of the right and left rails on the column end
of the unit.)
2.
3.
Next, lift up the glideboard and slide it off the
frame of the exerciser. When the bench is
completely off the exerciser, set it aside.
2.
Next, remove the 2 small safety hitch pins and
fold the exerciser together as described above.
Be sure you reinsert the 2 hitch pins before folding.
— 13 —
Download from Www.Somanuals.com. All Manuals Search And Download.
TOTAL GYM 1000 PARTS LIST
®
PART # PART DESCRIPTION
QTY.
PART # PART DESCRIPTION
QTY.
2
PART # PART DESCRIPTION
QTY.
1
2
Vertical Column
Tube Rollers
Stoppers
1
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
Left Fender
31
32
33
34
35
36
37
38
39
40
Pulley Assembly
Handle Assembly
Wing
4
2
1
2
2
3
1
1
1
1
2
Right Fender
Fender Bolts
Wheels
2
3
4
4
4
Screws
3
4
Grips
5
Washers
14
7
Wheel Spacer Tube
Adjustment Tube
Plastic Slide Bushing
Square Tube Cap
Round Tube Caps
Eyebolts
4
Foam Pads
Pins
6
Nuts
1
7
Screws
4
1
Leg Pulley
Bracket
8
Upper Rail (right & left)
Center Support Rail
Rectangular Tube Caps
Plastic Bushings
Shaft
1
1
9
1
6
“D” Ring
10
11
12
13
14
15
6
2
Harness
4
Eyebolt Nuts
Nut Caps
2
1
2
LITERATURE PACK
Lower Rail
1
Safety Hitch Pins
“C” Pin
2
41
42
43
Owner’s Manual
1
1
1
Platform
1
1
Exercise Booklet
Warranty Card
Platform Rail
1
Cable Assembly
1
23
A
22
24
31
26
27
30
29
18
21
31
16
28
20
19
24
26
14
27
17
A
18
19
20
28
32
25
19
38
17
39
37
20
31
15
36
18
20
24
40
1
34
16
18
10
19
33
8
11
24
9
34
2
35
10
4
36
6
3
12
5
13
36
4
7
2
3
3
7
— 14 —
Download from Www.Somanuals.com. All Manuals Search And Download.
OWNER’S PURCHASE RECORD
Total Gym® 1000 Exerciser
Date Purchased
Purchased From
Serial Number
(located on the height adjustment column)
Important! Save your sales receipt. You may wish to tape or staple it into this book.
©1997 and ©1999 Fitness Quest® Inc. All rights reserved. Made in Taiwan.
©1997 Total Gym Fitness, Ltd. All rights reserved. Total Gym® is a registered trademark of Total Gym
Fitness Ltd. U.S. Patented #405,132. Foreign patent pending. No part of this booklet may be reproduced
or utilized in any form by any means, electronic, mechanical or otherwise, without express written consent
of the copyright holder.
Download from Www.Somanuals.com. All Manuals Search And Download.
|