LDS9000
™
AirFreeCA Dispenser
Operating Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Page
Getting Started.............................................................................................4
Specifications ...............................................................................................5
Operation.....................................................................................................6
Program Control ..........................................................................................7
How to Use the Control Panel.....................................................................8
LDS9000 Gun Assembly...........................................................................10
Attaching the Syringe ................................................................................11
Removing the Syringe................................................................................13
Program Function.......................................................................................14
How to Make a Bead .................................................................................17
Operating Tips ...........................................................................................18
Loading the Reservoirs...............................................................................20
Alternative Filling Methods .......................................................................21
Defining the System...................................................................................22
How the LDS9000 Works .........................................................................26
Troubleshooting..........................................................................................27
Glossary......................................................................................................28
Accessories .................................................................................................30
Dispenser Component Selector Guide......................................................31
Two Year Fault Free Warranty....................................................................32
Meets applicable CSA and CE requirements.
This manual is for the express and sole use of Fishman dispenser users and purchasers,
and no portion of this manual may be reproduced in any form.
Fishman, AirFree, AirPulse, PosiLok, FreeFlow, SafeLok and DripFree are trademarks
of Fishman Corporation. © 2004 Fishman Corporation
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
This manual contains all the information you will need to set up and test
the 9000 series AirPulseTM dispensers.
• You will find the hook up for the LDAV on pages 10-15. For the
MDAV, review 16-19. For the SDAV review 20-23.
• Next, pages 24-25 will show your how to set up and test a thick
paste-like material.
• Finally, pages 26-27 explain how to dispense watery fluids using
vacuum control.
The remainder of the manual applies to all 9000 series AirFreeTM
dispensers.
First Steps
1
Unpack the shipping box and use the supplied checklist to assure all
items are present. If an item is missing, please contact us immediately.
2
Make sure the set up area has access to power. No compressed air will
be needed. You are about to experience the world’s only AirFreeTM
fluid dispenser. No compressors, no filtration, no plumbing.
3
Activate your extended two (2) year no-fault warranty by following the
instructions in the enclosed “On Line Warranty” letter to activate online.
Once your dispenser is set up, return to this section to familiarize
yourself with the multiple functions of the program controls.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Input Voltage:
100-240 VAC
47-63Hz
Max Inrush Current:
Output Voltage:
Output Power:
Fuse Rating:
3.2A/1.8A
5.0VDC
4.6W
1.0A/250 VAC
Initiate Circuit:
Drive Motor:
Foot Pedal (dry contact), finger switch
LDAV
7.5 Degree 48 Steps/Rev
MDAV 3.75 Degree 96 Steps/Rev
SDAV
LDAV
3.75 Degree 96 Steps/Rev
Axial Movement:
.024 Axial Pitch, .0005"/Step
MDAV .024 Axial Pitch, .00025"/Step
SDAV .012 Axial Pitch, .000125"/Step
Control Circuitry:
Interface:
CMOS microprocessor
Tactile key pad
.23ml
Minimum Dispense Volume:
Control Unit
Size:
7.63 x 8.75 x 3.5in (19.4 x 22.2 x 8.9cm)
5.8lbs
Weight:
Gun:
Length:
7.15in
Weight:
7.4oz
Cable Length:
3 or 6 feet
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
The LDS9000 Dispensing System uses a patented Linear Drive System
(LDS) to transfer force from the drive motor to the syringe piston. The
motor, lead screw and syringe piston are linked mechanically. Each
attachment (gun to reservoir, gun to piston, piston to reservoir) is
specifically designed to provide zero flexing in the system during a
dispense. Simply put, zero flexing is what makes the LDS9000 the
world’s most repeatable dispenser.
Once the dispense cycle is complete, a
programmed mechanical pullback retracts the
drive rod which is mechanically attached to
the AirFreeTM piston. The combined action of
the plunger with the preprogrammed forward
steps, and pullback feature produces a highly
repeatable deposit with no post-dispense
ooze. A pause between forward and reverse
motion can be programmed in for use with
compressible fluids.
Flexible
Control
Cable
Patented
Linear
Drive
System
The inner diameter and length of the syringe
barrel are used to calculate dispense volume.
For example, the inner diameter of a 10cc
syringe barrel measures 1.63cm. One forward
step of the motor moves the drive rod/piston
.00127cm, resulting in .0026cc of fluid being
displaced. With a 5cc barrel, it takes two
steps to displace the same amount of fluid.
Flexible Control Cable
An electronic signal is sent via the electronic
control cable that connects the dispense gun
to the control box. The signal energizes the
motor pushing the drive rod, attached to the
piston, into the syringe barrel. The forward
motion forces the fluid out to make a deposit.
Power Supply
The LDS9000 features a universal power
supply. It automatically adjusts for input
voltages ranging from 100 VAC to 240 VAC.
There is no adjustment required by the user.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Program Control
LCD Display
Power
On/Off
Control
Pad
Extend
Auto
Foot
Control
Toggle
Switches
Retract Manual
Hand
Gun Port
Manual/Auto Dispense
• Each mode provides you access to different features on the liquid crystal
display. Use the Auto/Manual switch to move back and forth from
manual mode to automatic mode.
• In manual mode, you can use the foot pedal to dispense a deposit or bead
“by eye”. You are in manual mode when the Auto/Manual toggle switch
is in the downward position.
• In Automatic Dispense mode, you can set several variables, including
program number, syringe barrel size, deposit volume, dispense rate,
pullback, delay. You are in automatic dispense mode when the
Auto/Manual toggle switch is in the upward position.
Reverse Motion—Drawback
In manual mode, flip the Extend switch, located on the control panel, from
Extend to Retract to engage the motor in reverse direction. This will draw
fluid back into the reservoir stopping any ooze.
Hand Control
In both manual and auto mode, flip the Foot/Hand switch, from Foot to
Hand to operate the dispenser with a finger switch. Finger switches are
sold separately.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
How to use the Control Pad
P SYRINGE:30CC
1 VOLUME: 4.99
Wait 3-5 seconds for
on-screen instructions
On Screen Instructions
When in program mode, if you are not sure what to do wait approximately
3-5 seconds and rolling instructions appear. If you missed them, not to
worry, they will repeat until you make an entry.
New or Saved Program
In Auto Mode hit the NEXT key. Hit the left arrow to enter a new
program or hit the right arrow to enter a saved program.
Edit the existing program
In Auto mode hit the BACK key once to enter the program manager. Each
time you hit the BACK key it shows a different program parameter. Find
the one you wish to edit, make your edit and hit the ENTER key. Hit the
NEXT key as many times as needed to return to program mode. Follow
on-screen instructions.
Enter a Volume
In Auto mode when entering a new program or editing an existing one,
when prompted for a dispense volume press the digit keys to type the
amount you require. Press the ENTER key to save your input.
Skip forward/back through the menu
In Auto mode, press the NEXT key to skip one slot forward in the
programming menu. Use the BACK key to skip back one slot in the
programming menu.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Use the Control Pad
Erase an Input or Make a Selection
In Auto mode when entering a new program or editing, use the left and
right arrow keys to erase and input or skip between choices such as
multiple saved programs. Use the ENTER key to select a choice.
Confirming a Choice
In auto or manual, always use the ENTER key to save an input or selection.
The NEXT or BACK keys do not save—they only skip to the next choice.
The ENTER key saves your data.
Jog Between Menu Choices
In auto or manual, always use the left or right arrow to move between
menu selections.
Back Panel
R5232/DB9
Foot Pedal
Power Cord
Receptacle
9
Download from Www.Somanuals.com. All Manuals Search And Download.
LDS9000 Gun Assembly
SureLok™ Retaining Ring Cover
Tip Cap
Barrel Reservoir
PosiLokTM Piston
Piston Hub
Lead Screw
Dispensing Gun
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Attaching the Syringe
1
Remove the end cap from the barrel reservoir.
• Make sure a tip cap is on the barrel.
2
Remove the retaining ring from the dispense gun.
3
Holding the dispensing gun with the piston hub
pointed upward, place the barrel over the piston
hub of the dispense gun.
4
Holding both loosely. Step on the foot pedal until
the barrel ears are raised at least 1/4” (.635mm)
above the plate.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
AttachinthgetShyerSinygrien(gceon(ctoinnutiendu)ed)
5
Manually twist the barrel in a clockwise
direction until the luer lock connector is
finger tight and the ears of the barrel are
flush against the retaining plate. It may be
necessary to set the EXTEND/RETRACT
switch to RETRACT and step on the foot
pedal to bring the barrel ears completely
flush to the retaining plate. If you set the
switch to RETRACT be sure to set it back
to EXTEND before proceeding.
Note: Do not over-tighten the barrel. It is
only necessary to make a loose connection
to bring the barrel flush. The Retaining
Ring holds the barrel in place. Over
tightening can damage the piston hub.
Also, do not over retract the barrel ears.
Over retraction will cause air pockets
between the piston and material.
6
Slide the retaining ring cover over the
syringe and rotate the cover in a clockwise
direction.
7
The syringe should be firmly connected to
the dispensing gun.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Removing the Syringe
1
At the end of a dispense program the
control unit will display a message:
“Remove syringe and press enter.”
2
Remove the retaining ring cover by
turning clockwise.
3
Slide the retaining ring cover over the
barrel reservoir.
4
Twist the barrel reservoir clockwise to
remove it from the piston hub.
• Discard the barrel reservoir.
• Press ENTER.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Program Function
The LDS9000 AirFreeTM Dispensing system allows 10 user-defined
programs to be stored in memory, ranging from 0 to 9. The program stores:
• Barrel reservoir size
• Deposit volume
• Dispense rate
• Backoff or Pullback
• Delay between forward and reverse motion
Follow These Steps to Input a Program
<-SYRINGESIZE->
3 5 10 30
• Press the NEXT key
1
1
Use the left and right arrow keys to select
your syringe size.
.01 cc
2
Enter your dispense volume by using the
.00261-12.2335
keypad to enter your volume followed by
pressing the ENTER key or use the left or
right arrows to use the SpeedBarTM feature*.
2
.392 cc/sec
.065 - 1.567
3
Enter your dispense rate by using the keypad
to enter the volume followed by pressing the
ENTER key or use the left or right arrows to
use the SpeedBarTM feature*.
3
4
Enter the amount of back off by using the
5 STEPS
0 - 500
keypad followed by pressing the ENTER key
or use the left or right arrows to use the
SpeedBarTM feature*.
4
5
Enter the amount of delay (0-9 seconds)
0 seconds
between forward and reverse motion by using
the keypad followed by the ENTER key.
.00 - 10.00
5
SpeedbarTM—This feature is available in the volume input,
*
dispense rate input and backoff input. Hold down the left or
right arrow key to make this feature appear. Continue
holding to make the bar increase or decrease. The longer
you hold, the faster the bar moves. When satisfied, release
the key and SpeedbarTM will show you your selected volume.
<- SHOTSIZE ->
0cc
12cc
8
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Program Function
1
To save program, answer YES followed
by the program number (0-9) of the
location you wish to save your
program.
SAVE PROGRAM?
<- YES NO ->
1
2
If you want the program to
automatically load as the default
program when the machine is turned
on, answer YES to the default question.
DEFAULT POWER-ON
<- YES NO ->
2
• Press the foot pedal to dispense the
first deposit
Follow These Steps to Edit a Program
• Press the BACK key to enter the program manager.
Tip: The BACK key moves through each parameter until you reach
the start of the program manager. The NEXT key moves you
through each parameter to the bottom of the program manager.
• Press the BACK key as many times as you need to get to the parameter
you wish to edit.
• Use the keypad to make your edit followed by the enter key.
• Use the NEXT/BACK keys to make any remaining edits.
• When finished, use the NEXT key as many times as needed to get to the
Save menu.
• Save your program edits.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Program Function
Follow these steps to save a program to a different location.
• Press the BACK key to enter the program manager.
• Press the NEXT key to enter the Save menu.
• Press the left arrow to make the save.
• Select a location by pressing a digit from 0-9.
STORED PROGRAM
<-REPLACE NO->
Tip: If the program you choose already has a saved
program you will be asked if you wish or
overwrite the program.
DEFAULT POWER-ON
<- YES NO ->
• Decide if you want your saved program to
default at start up by choosing yes or no.
Follow these steps to restore a program at Start Up.
• Press the right arrow to enter the Save menu.
PROGRAM MANAGER
<-NEW SAVED->
• If you know the number of the program you
wish to restore, press the number now on the
keypad to restore the program.
• If you do not know the program number hit the right arrow to
review the saved programs.
Tip: The programs will automatically scroll in order from 0-9. Don’t
worry if you miss a program, the scroll feature will repeat until
you make a selection
• When you see the program you want appear on the screen press
the NEXT key and the program will restore.
Follow these steps to restore a program while in an active
program.
• Press the NEXT key.
• If you know the number of the program you wish to restore,
press the number now on the keypad to restore the program.
• If you do not know the program number hit the right arrow to
review the saved programs.
Tip: The programs will automatically scroll in order from 0-9.
• When you see the program you want appear on the screen press
the NEXT key and the program will restore.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Make a Bead
To dispense a continuous bead of fluid instead of
a single dot, follow these steps.
Extend
Auto
Foot
1
Switch the AUTO/MANUAL switch to
MANUAL.
Retract Manual
Hand
1
.00261 cc
2
Set the shot size to the lowest setting.
.00261-12.2335
2
3
.065 cc/sec
.065 - 1.567
For best results, set the dispense rate to slow,
to minimize backpressure in the syringe.
3
5 STEPS
0 - 500
4
As a beginning point, set drawback to 5 steps
4
5
Keep delay set to zero, then adjust as needed
0 seconds
to eliminate any post dispense ooze.
.00 - 10.00
5
• Press and hold the foot pedal until the
required amount is dispensed.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Tips
Suggested Tips
• The faster you dispense the more backoff you will need. That’s because
the speed at which the piston is traveling exceeds the flow rate of the
material out of the dispense tip. Therefore, creating internal pressure. More
reverse motion is required to get the internal reservoir pressure back to
zero. We recommend you start with a slow rate and progress from there.
• The LDS9000 positively displaces fluids. That means if you program
.02cc’s of fluid, you will get .02cc’s out of a very small tip or a large tip.
The only difference is trying to force the fluid through a very small tip will
take twice as long. We recommend you increase the fluid flow by using our
FreeFlowTM tapered tip.
• A change in the dispense rate will change your deposit size. When the
piston moves forward it often exceeds the flow rate of the fluid, thus
creating pressure buildup. The best way to rapidly relieve that pressure is to
apply reverse motion. When the dispense rate is doubled the fluid has half
the time to flow before reverse motion, therefore the deposit size becomes
smaller. Conversely, when the dispense rate is cut in half the fluid has twice
the time to flow before reverse motion, therefore the deposit size becomes
larger. The only way to maintain the same deposit size at all speeds is to
adjust all parameters.
First Shot Set Up
•Follow the steps listed in the LDS9000 Rapid Setup Guide. We
recommend you work with the Fishman test fluid provided in your
dispenser to establish the first deposit.
•When priming your dispense tip watch how long the fluid flows out of
the tip. Little to no ooze, start with a minimum amount of backoff (1-10
steps). Lots of ooze, start with a higher amount of backoff (10-25 steps)
and adjust from there.
•Start with a slow dispense rate and adjust your dispense volume and backoff
until you achieve the right size deposit. Once your deposit is stabilized try
adjusting the speed to your liking, watch the effect on your deposit. Return
to volume and backoff to tweak the deposit size. Always allow the deposit to
stabilize via 5 or 6 dispenses before making the next adjustment.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Tips
Components
• Always use Fishman AirFree™ barrel
reservoirs and dispense tips. Safely
dispose after use. This method prevents
contamination, ensures proper safety
and provides maximum cleanliness.
• The heart of the Linear Drive System
(LDS) is the AirFree™ piston. The
specially designed luer connection
provides a no slip connection assuring
the highest deposit repeatability.
• Use Fishman FreeFlow™ tapered dispense tips. Small gauge tips will
only create backpressure, put stress on the fluid and cause ooze. The
Linear Drive System will positively displace fluids, which allows the use
of larger tips with no effect on performance. The FreeFlow™ taper tips
eliminate fluid flow restrictions preventing drooling and ooze.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Loading the Reservoirs
Avoid Air in the Syringe Barrel
Trapped air in the fluid creates voids that will make the fluid
compressible. Although the LDS9000 Linear Drive System is
stable enough to handle most compressible fluids excess air will
force the user to use a greater amount of pullback. This will create
a greater amount of forward and reverse motion in the syringe
during a dispense cycle. Excess motion will put more stress on the
fluid being dispensed. The goal is to reduce dispense motion as
much as possible to protect the fluid and maximize repeatability.
Paying attention to minimization during syringe filling will
drastically improve performance.
For best results, use a Fishman barrel filing station (see next page).
If needed, use a centrifuge or vacuum chamber to eliminate any
trapped air.
Pourable Fluid
Twist on a tip cap and pour your
fluid into the barrel using a funnel.
Insert a Venting Ribbon along the
inside edge of the barrel, followed
by an AirFree™ piston. Carefully
press down until it contacts the
fluid. While holding the piston in
place gently pull the Venting
Ribbon from the barrel.
Thick or Non Leveling Fluid
If the fluid comes packed in a
caulking cartridge try loading the
reservoir with a caulking gun. If
not, spoon-feeding with a spatula
often works. Follow the loading by
inserting the Venting Ribbon along
the inside of the barrel, followed
by AirFree™ piston. Carefully
press down to move the fluid to
the bottom of the barrel and to
remove trapped air. While holding
the piston in place gently pull the
Venting Ribbon from the barrel.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Alternative Filling Methods
• If your fluid comes prepackaged in a medical style syringe use the
Fishman B250001 luer-to luer fitting to transfer the material from
prepackaged syringe to the Fishman syringe.
• Another option is to use the Fishman C370001 AirPulseTM reservoir filler.
Purchase your fluid in a 12oz cartridge or prepack the cartridge yourself.
The prepackaged cartridge easily sips into the barrel loader. Air pressure,
activated by a finger switch, transfers the fluid from the cartridge to the
Fishman syringe (piston inserted), filing from the bottom up.
•If the fluid comes prepackaged in a 1/10 gallon caulking style cartridge
use the Fishman B250001 barrel loader. Operation is exactly as above; the
only difference is the reservoir is designed to fit the caulking cartridge.
For additional assistance, contact one of our Application Specialists:
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Defining the System
Program Mode
Program mode is ideally suited for dot type applications or automated
(XYZ system) beads. This mode allows you to program a desired volume of
fluid for repeated and consistent output. In the program mode there are
two utilities. Program Manager and the Save/Restore Manager.
Utility 1: Program Manager
The Program Manager has five adjustable parameters:
• Barrel Selection
• Dispense Volume
• Dispense Rate
• Drawback
• Drawback Delay
Barrel Selection:
The selection of the proper barrel is critical to positive
displacement dispensing. For the best results always select the
smallest barrel reservoir that will work for your application. To
minimize set up time we preprogrammed the control unit using
standard Fishman luer lock barrels. Simply select the proper size
(3,5,10,30) and move to the next parameter.
Dispense Volume:
Having the ability to enter a dispense volume is what separates the
LDS9000 from traditional pneumatic dispensing systems. Our
patented technology allows us to apply a formula based on the
syringe’s inner diameter and the distance traveled by the PosiLokTM
piston to arrive at the desired volume. This method drastically
reduces the amount of time consumed by the guesswork of the
pneumatic systems.
Dispense Rate:
This is an important parameter that allows the LDS9000 to
dispense a wide range of material. By altering the speed at which
the Linear Drive System travels down the barrel, we can dispense
non-compressible to thixotropic materials with little to no impact
on rheology. The microprocessor calculates dispense rate in the cc
per second.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Defining the System
Drawback:
Upon completion of the dispense cycle, fluid oozing out of the
dispense tip is a common problem when dispensing compressible
fluids. The Drawback parameter eliminates any oozing by
implementing a mechanically reversed action at the end of the
dispense cycle. Because the system is intelligent, it knows the
distance traveled forward and the distance traveled back.
Therefore, on the next dispense cycle, the system will add the
distance traveled back to the forward motion, guaranteeing a
positive displaced dispense every time.
Example: The system
converts dispense
volume to motor
steps. Assume .02cc
equals 20 steps. The
following is what
happens when 10
steps of reverse
motion is added.
Drawback Delay:
This parameter is most useful when potting or beading with a
compressible fluid. A delay (in seconds) is applied between the
end of the forward motion and the start of the reverse motion
when drawback steps are programmed. This allows the entire
programmed shot to dispense prior to the reverse motion.
Utility 2: Save/Restore Manager
The Save/Restore Manager has three adjustable parameters:
• Save your program to ten locations
• Recall your program from ten locations
• Set a program as the default on start up.
The Save/Restore Manager allows you to save and recall up to ten
different programs, eliminating setup time when changing dispense
volumes. Also, you may specify one program as the default
program meaning this program will automatically load when the
controller is turned on. This is useful when multiple LDS9000 are
used on a production line. You are assured all systems will start
with the same program.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Defining the System
Manual Mode
Program is ideally suited for priming the dispense tip and manual
dispensing such as potting and beads. In manual mode the parameters and
function of the parameters are exactly the same as program mode. The only
difference is that the system will only dispense fluid for the amount of
time the user holds the foot pedal down.
The Linear Drive System
AirFree PosiLokTM Piston—
The heart of AirFree dispensing
This unique design has made positive displacement with a barrel
reservoir possible. Re-engineering the pneumatic piston concept,
the high interference fit of the piston and the luer lock connection
with the Linear Drive System enables intelligent dispensing. By
increasing the interference between the O.D. of the piston and the
I.D. of the barrel, we are able to completely seal the chamber
eliminating material leakage. The luer lock connection provides
complete control over forward and reverse motion. The intelligent
control unit microprocessor knows the barrel I.D., the distance
traveled forward and the distance traveled backward. With every
dispense cycle the piston moves the exact distance every time,
guaranteed. Drip-free dispensing, air pocket venting and all-plastic
component dispensing are maintained with the new design.
The Dispense Gun—
The precision of AirFree dispensing technology
The motor used inside the dispense gun is a linear actuator. The
linear actuator creates forward motion by rotating nut between
electrically charged poles. The drive screw runs through the nut
located at the center of the motor. The design of the plastic gun
housing captures the top of the drive screw preventing it from
rotation. When electrically charged, the center nut will step from
one magnetic pole to the other, moving the drive screw forward. It
is important to note that the drive screw not rotating allows the
attachment of the PosiLokTM piston, creating the linear motion
critical to positive displacement. By reversing the charge, we are
able to create reverse motion.
Note:
LDAV one electrical pulse (motor step) = .0005"
MDAV one electrical pulse (motor step) = .00025"
SDAV one electrical pulse (motor step) = .000125"
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Defining the System
Retaining Ring—
The brawn of the AirFree dispensing technology
The multi-legged stainless steel design locks the syringe in place,
making the syringe and gun one. In dispensing, any flexing
between the barrel reservoir and surface to which it is secured
represents a pressure loss and will change the amount of fluid
dispensed. Due to the tight tolerance between the stainless steel
retaining ring and the gun, there is no room for barrel flexing
when the thrust-of-dispense cycle is applied. This is a key
contributor to maintaining positive displacement dispensing.
The Control Unit—
The brains of AirFree dispensing
The control unit gives the user control over volume output;
dispense rate, reverse motion and motion delay. By imputing and
manipulating these parameters, the microprocessor will calculate
the number of steps needed to achieve the requested result. A
universal switching power supply automatically adapts to multiple
AC inputs. The foot pedal may be removed for automated
activation using a dry contact.
Helpful Hints
Priming the System
Removal of the tip cap and introduction of a new needle traps air
pockets inside the stem of the syringe and hub of the needle.
Because our system positively displaces fluid, it is very important no
air is present in any portion of the syringe. Therefore, it is important
that any trapped air is pushed out of the syringe prior to dispensing.
Changing Barrels Reservoirs
Same Size Barrels: Simply switch one barrel for the next. The
only consideration is to prime the new dispense tip prior to
dispensing (page ?). The LDS9000 recognizes barrels of the same
size so it is not necessary to reset the system.
Different Size Barrels: When changing to a different size barrel, it
is necessary to reset the lead screw, reset the dispense parameters
and prime the dispense tip. To reset the lead screw remove the
barrel reservoir, flip the Auto/Manual switch to Manual and the
Extend/Retract switch to Retract. Hold the foot pedal down until
the lead screw retracts all the way into the dispense gun.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
How the LDS9000 Works
With the power ON, here’s what happens
when you press the foot pedal:
1
The program is engaged, the motor is energized beginning the dispense
cycle countdown.
2
The motor pushes the lead screw, with piston attached to the end,
down the barrel pushing the liquid out the dispensing tip.
3
At the end of the program, the motor is de-energized—stopping
forward movement of the lead screw and stopping all fluid flow.
4
If drawback is programmed, the motor is re-energized and begins a
drawback cycle countdown.
5
The motor retracts the lead screw, with piston attached to the end,
creating a vacuum that stops any post dispense oozing. The vacuum is
controlled by the software program.
When in manual mode the microprocessor switches to direct motor
control by the foot pedal. As long as the foot pedal is pressed, the motor
remains energized, providing a flow of liquid for filling or beading.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Problem: The fluid continues to ooze long after the dispense, (including
drawback) is completed.
Potential Solutions:
•Check the needle size. The unpredictable nature of the
pneumatic drive system has forced customers to use the needle as
a flow control. What this means is that they use an ultra small
(25G) needle to control the flow fluid because the pneumatic
drive system can’t.
IMPORTANT: Using an ultra small needle works against our system.
Because we positively displace, we can get the same amount out of a
14G as a 25G. Use the needle with the largest I.D. and shortest length
possible, preferably a free flow tip, to reduce backpressure.
•Check that the syringe is packaged air free. The presence of air
will cause oozing. It is recommended the syringes be packaged
using centrifuge or vacuum when possible.
•Make sure you are using an PosiLokTM piston. Pistons are included
in your dispense kit.
Problem: The fluid is blowing by the AirFreeTM piston.
Potential Solutions:
•Examine the seal of the piston. Sometimes syringe fillers, either
by rushing or attempting to squeeze air out, allow fluid to
permeate the front seal of the piston. When the front seal is
maintained the piston will not leak. Also, adding a Fishman Piston
Stabilizer will help. See Accessories for ordering information.
•Make sure you are using Fishman Syringes. The inner diameter
has been preloaded into the software for dispense calculations.
Competitor’s syringes have different diameters, which will cause
problems trying to achieve the dispensed amount.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
FOOT .................................Setting for using a foot pedal to activate dispensing cycle
HAND................................Setting for using finger switch to activate a dispense cycle
SYR.....................................Syringe— barrel reservoir selection
DIA.....................................Length—user-defined syringe inside length from ears to bottom in
millimeters
V.........................................Volume—Volume to be dispensed, in cubic centimeters
R .........................................Dispense Rate—The rate, in cubic centimeters per second, at
which you want to dispense the fluid
PRGM.................................Program key to enter or exit at AUTO DISPENSE PROGRAM
MANAGER
ENTER ...............................Key to activate desired parameter
NEXT.................................Key to advance to the next screen without changing the exiting
parameters
SYRINGE
ATTACHMENT.................The ideal position for the ears of the barrel reservoir after locking
it into place, is flush up against the retaining plate. Note: Always
attach a new barrel reservoir with the tip cap on.
PRIMING
THE SYSTEM ...................Eliminates any trapped air between the barrel reservoir and
needle. Always prime the system at start up.
PARAMETER
LIMITS ...............................If you want to know the min., max, or high and low values of
parameters for a given syringe, type in 999 at the prompt and
press the ENTER key. View the display; it will flash the values
on the screen and then return.
RETRACT ..........................When you are in program mode and you change the
EXTEND/RETRACT switch to RETRACT, the system will
prompt you to hit the ENTER key or flip the switch back to
EXTEND. This is a safety precaution. If you retract with the
PosiLokTM piston attached, the barrel reservoir will fill up with air
from the open end. Before you use the retract feature, be sure
you remove your barrel reservoir. When retracting the lead screw
in manual mode, all you have to do is flip the
EXTEND/RETRACT switch to RETRACT. The PosiLokTM
piston will retract for as long as the foot pedal is depressed.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
DISPENSE RATE...............Always start with the slowest recommended rate and increase
incrementally.
DRAWBACK DELAY.........When using a small needle you can take advantage of the
drawback delay feature to give you more control over your output
volume. This feature allows the fluid to flow out of the syringe
before you drawback the PosiLokTM piston and begin your next
dispense cycle.
FACTORY SETTINGS .......The factory settings will be replaced with your settings when you
save into location #1 and #2
SAVE...................................When you save an application into a location that has a
previously stored application, you will be asked to replace the
existing application.
RESTORE ...........................When you restore an application from a location, the parameters
will flash on the display. You will then be asked to restore the
application.
ACTIVATING
A PARAMETER..................if you notice that a parameter that you set didn’t take effect,
make sure you pressed the ENTER key before proceeding to the
next screen. If you did not press the ENTER key, the values you
entered will not take effect on the next dispensing cycle.
NEEDLE SELECTION ..... When selecting a needle we recommend using the FreeFlowTM tip
with the LDS9000. This tip allows the least amount of flow
restriction thus allowing positive flow of the fluid from the
syringe.
PREPACKAGED
SYRINGE ..........................Must be free of air pockets to receive the full benefits of the
LDS9000. Contact your Fishman representative for AirFreeTM
filling suggestions.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Dispenser Component Selector Guide
The charts below are only a small sample of available Fishman components.
Please refer to the complete Fishman catalog to view the entire product line.
Retaining Ring
PosiLokTM
Flexible
The unique multi-legged
design firmly locks the
barrel into place
eliminating any possibility
of pressure loss during dispense.
Dispense Tips
Soft polypropylene burr and flash free tips
assure accurate deposit control.
Gauge ID
.5”
1.5”
Color
Quantity
Per Pack
Size
Retaining Ring
15G .049” Z532115 Z534115 Brown
18G .032” Z532118 Z534118 Dk. Green
20G .019” Z532120 Z534120 Pink
3cc
10cc
O312291
O314291
1
1
25G .014” Z532125 Z534125
Red
AirFreeTM CA
Barrels/Pistons
Accessories
Gun Stand
Each package contains
same amount of barrels
and PosiLok™ engageable
pistons.
Holds the dispense gun when not in use.
LDS9000 Stand D600001
Quantity
Per Pack
Size
Clear
Piston Stabilizer
3cc
O502051
O504171
50
30
10cc
Attaches to the end of the Linear
Drive System dispense rod. Clam
shell design clamps
onto the piston hub.
Each kit contains a
piston stabilizer, assembly
tool and instructions
PosiLokTM
Teflon®-
Lined
Dispense Tips
5cc Stabilizer Kit
10cc Stabilizer Kit
30cc Stabilizer Kit
Y010101
Y020101
Y030101
ID
1/2” Length
Hub Color
.020”
.006”
Z592121
Z592125
Gray
Pink
Automation Gun Bracket
Mounts the gun to an XYZ
dispense station.
LDS9000 Bracket
Y200001
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Two Year Fault-Free Warranty
Fishman Corporation (Fishman) warrants its product to be
free from defects in materials and workmanship for a period
of two years from the date of purchase.
Under this warranty, Fishman will repair or replace any defective
part or, at its own option, the complete dispenser regardless of
fault. To obtain service under warranty, product must be
returned, freight prepaid, to Fishman.
Before use, the customer must determine the suitability of
the product for their intended use and therefore customer
assumes all risk and liability connected with products use.
At no time under any circumstance shall any liability or
obligation of Fishman arising from the warranty exceed the
purchase price of the product.
Except as provided herein, Fishman makes no warranties,
express or implied, including warranties of merchantability
and fitness for a particular purpose. In no event will Fishman
be liable for direct, indirect, special, incidental, or
consequential damages arising out of use of this product.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Fishman Corporation
192 South Street
Hopkinton, MA 01748
800-433-2115 Fax 508-435-2119
www.fishmancorp.com
email: [email protected]
270264
Download from Www.Somanuals.com. All Manuals Search And Download.
|