Fisher Price Satellite Radio N9326 User Manual

N9326  
www.fisher-prrice.com  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Important!  
• For proper setup and use, please read these instructions.  
• Please keep this instruction sheet for future reference, as it contains important information.  
• Transmitter operates on AC current. Receiver operates on AC current (use enclosed AC adaptor) or  
3.6V NiMH rechargeable battery pack (included).  
• Before first time use, charge the rechargeable battery pack for four hours.  
• Adult assembly is required for wall mounting. Tools needed for assembly: electric drill, ¼" drill bit,  
hammer, Phillips screwdriver (tools not included).  
• This product is not intended to be used as a medical monitor and its use should not replace  
adult supervision.  
• Test sound/audio reception of receiver before first-time use and whenever you change location of  
the transmitter.  
Adults Note: Periodically examine this product for damage to the cord, housing or other parts that may  
result in the risk of fire, electric shock or injury. If the product is damaged, do not use it.  
• Never use extension cords with the AC adaptor.  
• Never use transmitter or receiver near water (i.e. bathtub, sink, wet basement, etc.).  
• Always use transmitter and receiver where there is adequate ventilation. To prevent overheating,  
keep away from heat sources such as radiators, heat registers, direct sunlight, stoves, amplifiers,  
fire, excessive heat or other appliances that produce heat.  
• Fisher-Price® does not recommend the use of two monitors in one house.  
• Always remember that you are using public airwaves when using your monitor. Conversations, even from  
rooms near your transmitter, may broadcast to other nursery monitors, radios, cordless telephones or  
scanners outside your home. To protect the privacy of your home, always turn off the transmitter when  
not in use.  
• Do not connect to more than the recommended number of power supplies.  
• The AC adaptor is not a toy.  
• Disconnect the AC adaptor from the receiver before cleaning.  
• If this product begins to operate erratically, you may need to reset the electronics. Turn the transmitter  
power/volume dial off and then back on; press the receiver main power/menu button to turn power off  
and press again to turn power back on.  
• Carrier Frequency: 2.4 Ghz  
• Product features and decoration may vary from photos.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Features  
6
7
2
14  
9
10  
13  
11  
5
3
1
12  
8
4
4
Receiver  
Transmitter  
AC Adaptor/Charger  
Transmitter Tabletop Stand  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Features  
Main Power/Menu Button – Press to turn receiver main power ON; press again for the main  
menu; press and hold for approximately five seconds to turn main power OFF.  
1
Power L.E.D. – Turns on when receiver power is ON.  
2
3
Menu Navigation/Volume Control Button – Press up, down or side arrows to scroll through menu  
options. When the menu is not on the screen, press the side arrows to adjust volume.  
Speaker  
4
5
Video Screen  
Video Screen On/Off Button – Press to turn the video screen on; press again to turn it off.  
Sound Lights – Shows you baby's sounds.  
6
7
DC Input Jack – Insert the AC adaptor/charger pin to use AC power/charge the battery.  
Camera Lens  
8
9
Power/Volume Dial – Rotate to turn transmitter power ON and adjust volume to a comfortable  
level for baby.  
10  
Microphone  
11  
12  
Music, Sounds and Night Light Buttons  
Music – Choose from 5 lullaby songs.  
Sounds – Play nature sounds.  
Night Light – Turn on night light for baby.  
Power L.E.D. – Turns on when transmitter power is ON.  
13  
14  
Night Light – Lights room with a soft glow.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wall Mount Parts  
Wall Mount Bracket  
Cord Wrap  
Base Stand  
Fasteners Shown Actual Size  
Wall Anchor – 4  
#8 x 2" Screw – 4  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Charging the Battery  
(Inside the Receiver)  
DC Input Jack  
IMPORTANT! Fully charge the receiver (with battery pack inside) for four hours before first-time use.  
Use only the included AC adaptor charger! Do not use any other adaptor charger.  
• Fit the AC adaptor charger pin into the DC input jack on the receiver.  
• Plug the AC adaptor charger into a standard wall outlet.  
Notes: If power flow to the wall outlet is controlled by a switch, make sure the switch is “ON”. Use the AC  
adaptor charger only in a wall outlet. Do not plug the AC adaptor charger into a ceiling outlet. To connect  
to a supply that is not in the United States, use an adaptor (not included and sold separately) with the  
proper configuration for the power outlet.  
• If you are monitoring baby while charging the battery pack, you will see the charging icon  
video screen.  
on the  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Testing Sound/Video Reception  
Test transmitter transmission and receiver reception before installing the wall mount bracket  
and cord wrap (if used) and each time you change location of use.  
Power Dial  
Radio  
• Place the transmitter in the room where you intend to use it.  
• Point the transmitter toward the area you will be monitoring. Adjust the camera angle by rotating the top  
portion of the transmitter up or down.  
• Turn the power/volume dial ON.  
• Turn on a radio.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Testing Sound/Video Reception  
Sound Lights  
Main Power/Menu Select  
Button  
• Place the receiver in the room where you intend to use it.  
• Press the main power/menu select button on the front of the receiver to turn power ON.  
• Adjust the receiver location for best reception.  
• When sound is picked up by the receiver, the sound lights will turn on.  
- One or two lights indicate quieter sounds.  
- Three or more lights indicate louder sounds.  
• If you cannot see an image on the receiver screen, adjust the transmitter location or camera angle.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Transmitter Wall Mount Installation  
WARNING  
To prevent strangulation with power cord, never  
place transmitter within reach of child.  
IMPORTANT! Test the reception of the monitor before installing the wall mount bracket and cord wrap.  
Use the assistance of one adult to hold the transmitter against the wall in the spot you want to install it.  
Then, test the reception of the receiver in several locations around your house. Please refer to the Testing  
Sound/Video Reception section of these instructions.  
Download from Www.Somanuals.co1m0. All Manuals Search And Download.  
Transmitter Wall Mount Installation  
6 ft.  
• To provide the greatest viewing range, we recommend you install the wall mount bracket at least six feet  
from the floor.  
• Make sure the camera lens does not have an obstructed view of your baby. Adjust the camera up or down.  
• Allow adequate ventilation of the transmitter when mounted. Do not mount the transmitter above heating  
vents or other heat producing sources. Do not mount the transmitter where it can receive direct sunlight.  
• Install the wall mount bracket on a flat section of the wall. The wall mount bracket cannot be  
corner mounted.  
• Make sure the AC adaptor will reach a wall outlet before installing the wall mount bracket. To prevent  
entanglement, never use an extension cord.  
Download from Www.Somanuals.co1m1. All Manuals Search And Download.  
Transmitter Wall Mount Installation  
Wall Mount Bracket  
1
• Hold the wall mount bracket against the wall in the location you want to install it. Make sure the wall  
mount bracket is straight.  
• Using a pencil, make a mark on the wall inside the upper hole and lower slot on the wall mount bracket.  
• Set the wall mount bracket aside.  
2
• Using a ¼" drill bit, drill one hole through each pencil mark you made on the wall.  
Download from Www.Somanuals.co1m2. All Manuals Search And Download.  
Transmitter Wall Mount Installation  
Wall Anchor  
3
• Fit a wall anchor into each of the drilled holes.  
• Tap each wall anchor lightly with a hammer until the ends of each wall anchor are even with the surface  
of the wall.  
4
• Align the holes on the wall mount bracket with the wall anchors.  
• Insert two screws into the holes in the wall mount bracket and tighten with a Phillips screwdriver. Do not  
over-tighten.  
Download from Www.Somanuals.co1m3. All Manuals Search And Download.  
Transmitter Wall Mount Installation  
Wall Mount Bracket  
Cord Wrap  
5
• Position the cord wrap against the wall, so that it is centered below the wall mount bracket and as close  
to the floor as possible.  
• Move the cord wrap approximately ½" towards the wall outlet.  
• Using a pencil, make a mark on the wall inside both holes in the cord wrap.  
• Set the cord wrap aside.  
Download from Www.Somanuals.co1m4. All Manuals Search And Download.  
Transmitter Wall Mount Installation  
6
• Using a ¼" drill bit, drill one hole through each pencil mark you made on the wall.  
Wall Anchor  
7
• Place a wall anchor into each of the drilled holes.  
• Tap each wall anchor lightly with hammer until the ends of each wall anchor are even with the surface of  
the wall.  
Download from Www.Somanuals.co1m5. All Manuals Search And Download.  
Transmitter Wall Mount Installation  
Cord Wrap  
8
• Align the holes on the cord wrap with the wall anchors.  
• Insert two screws into the holes in the cord wrap and tighten with a Phillips screwdriver.  
Do not over-tighten.  
Transmitter  
Slot  
Base Stand  
Slot  
Wall Mount Bracket  
9
• Put the transmitter into the base stand.  
• Fit the transmitter cord into the slot in the base stand and the wall mount bracket.  
• Slide the stand into the slot on the wall mount bracket.  
Download from Www.Somanuals.co1m6. All Manuals Search And Download.  
Transmitter Wall Mount Installation  
6 ft.  
Groove  
Cord Wrap  
10  
IMPORTANT! Make sure the cord is taught between the transmitter and cord wrap. Excess cord can form  
loops or extend into the crib and present a strangulation hazard.  
• Extend the transmitter cord straight down the wall to the cord wrap.  
• Wrap the transmitter cord around the cord wrap, leaving just enough to reach the wall outlet. Make sure  
there is no slack in the transmitter cord.  
• Thread the transmitter cord through the groove in the front of the cord wrap. Make sure the transmitter  
cord is fully inserted in the groove.  
• Plug the transmitter cord into the wall outlet.  
Download from Www.Somanuals.co1m7. All Manuals Search And Download.  
Setup/On Screen Displays  
Main Menu  
• First, turn both transmitter and receiver  
power ON. Then press the main power/  
menu select button on the receiver to  
see the main menu.  
• Press the up, down or side arrows to  
scroll through menu options. As you  
scroll, the menu choices highlight and  
blink on the screen.  
• Press the main power/menu select  
to choose:  
Music  
Sounds  
MAIN POWER/  
MENU SELECT  
Night Light  
Voice Activated Screen  
Contrast/Brightness  
Turn Main Menu Off  
Hint: The main menu turns off if you  
do not scroll through choices or make  
a selection within approximately  
15 seconds. Simply press the main  
power/menu select button again to  
return to the main menu.  
• You can turn on music or sounds and  
a night light for baby. You cannot turn  
on both music and sounds.  
Download from Www.Somanuals.co1m8. All Manuals Search And Download.  
Setup/On Screen Displays  
Music  
Turn music off  
Turn music on and cycle through  
all five songs  
Select song number one  
Select song number two  
Select song number three  
Select song number four  
Select song number five  
Return to previous menu  
Exit menu  
If you turn the music ON the music  
icons  
will appear on the bottom of  
the screen.  
Sounds  
Turn sounds off  
Select nature sounds  
Select heartbeat sounds  
Return to previous menu  
Exit menu  
If you turn sounds ON one of the  
sound  
icons  
or  
will appear  
on the bottom of the screen.  
Download from Www.Somanuals.co1m9. All Manuals Search And Download.  
Setup/On Screen Displays  
Night Light  
Turn night light off  
Turn night light on  
Return to previous menu  
Exit menu  
If you turn the night light on the night  
light  
icon will appear on the bottom  
of the screen.  
Voice Activated  
(For Nighttime Use)  
Video screen turns on for 30 seconds  
and then turns off. When baby  
makes noise, video screen automati-  
cally turns back on. It will remain on  
and turn off after 30 seconds from  
the last sound detected. You can also  
press any button on the receiver to  
turn video back on.  
Video screen does not turn on when  
baby makes noise. Press the video  
screen on/off button on the top of the  
receiver to turn the video screen on  
and off.  
Return to previous menu  
Exit menu  
Download from Www.Somanuals.co2m0. All Manuals Search And Download.  
Setup/On Screen Displays  
Contrast/Brightness  
Press left or right side arrows to  
adjust contrast on the screen.  
Return to previous menu  
Exit menu  
Press left or right side arrows to  
adjust brightness on the screen.  
Return to previous menu  
Exit menu  
Download from Www.Somanuals.co2m1. All Manuals Search And Download.  
Setup/On Screen Displays  
Out of Range  
The out of range warning will flash on the  
screen and you will hear a tone when the  
receiver is out of range or the transmitter  
is turned off.  
Battery Indicators  
Indicates receiver is using  
battery power (only on the  
menu screen).  
Indicates battery power is low  
(and you will hear a tone). Plug  
in the AC adaptor/charger  
to use AC power and charge  
the battery.  
Indicates receiver is charging.  
Download from Www.Somanuals.co2m2. All Manuals Search And Download.  
Use  
IMPORTANT! Test the sound and video reception of the monitor before first time use and whenever you change  
the location of the transmitter (see Testing Sound/Video Reception section of these instructions).  
• Place the transmitter in the same room with child. Fit the transmitter into the tabletop base. Position the  
camera lens so it is facing child. For the best viewing range, the transmitter should be approximately  
five feet away from baby.  
• Unwrap and fully extend the power cord for best transmission. Plug the power cord into a standard  
wall outlet. Use the power cord only in a wall outlet. Do not plug the power cord into a ceiling outlet.  
Note: The microphone is located on the power cord. Do not place the transmitter microphone within reach of  
your child or in front of the transmitter. For best results, allow the cord to extend behind the transmitter.  
• Turn the power/volume dial to turn the power ON. The power L.E.D. will light.  
• Press the music  
• Press the sound  
button to play lullaby songs. (Press again to turn off the music.)  
button to play nature sounds. (Press again to turn off the sounds.)  
• Press the night light button  
for a soft, glowing light. (Press again to turn off the night light).  
Download from Www.Somanuals.co2m3. All Manuals Search And Download.  
Use  
• To use AC current, unwrap and fully extend the AC adaptor cord (for best reception). Insert the AC  
adaptor pin into the DC input jack on the receiver and plug into a standard wall outlet.  
• Press the main power/menu button on the receiver to turn the power on.  
• Press the side menu navigation buttons to turn the receiver volume up  
or down  
.
• To monitor baby without video, press the video on/off button at the top of the receiver. To turn video back  
on, simply press the button again.  
• The receiver can be used to stay in touch with baby around your house or yard. The receiver’s range is up  
to 400 feet (122 meters) away from the transmitter. The out of range warning will flash on the screen  
and you will hear a tone when the receiver is out of range.  
• To turn off the receiver, press and hold the main power/menu button for approximately five seconds.  
Download from Www.Somanuals.co2m4. All Manuals Search And Download.  
Night Vision Mode  
When the light in baby’s room is too low,  
the transmitter will automatically switch  
to night vision mode. The image on the  
receiver screen will appear in black and  
white, not color.  
Download from Www.Somanuals.co2m5. All Manuals Search And Download.  
Battery Replacement  
If you need to replace your NiMH rechargeable battery pack, please contact Fisher-Price® Consumer  
Relations at www.service.fisher-price.com or call 1-800-432-5437.  
• Locate the battery compartment door on the back of the receiver.  
• Loosen the screws in the battery compartment door with a Phillips screwdriver. Remove the battery  
compartment door.  
• Remove the exhausted battery pack and dispose of it properly.  
• Plug the new rechargeable battery pack into the receiver’s battery connector. Then, insert the battery  
pack in the battery compartment.  
• Replace the battery compartment door and tighten the screws with a Phillips screwdriver.  
Do not over-tighten.  
• Protect the environment by not disposing of this product with household waste (2002/96/EC).  
Check your local authority for recycling advice and facilities (Europe only).  
Battery Safety Information  
In exceptional circumstances, batteries may leak fluids that can cause a chemical burn injury or ruin your  
product. To avoid battery leakage:  
• If replacing the battery pack, insert it as indicated inside the battery compartment.  
• Always remove an exhausted battery pack from the product. Dispose of the battery pack safely.  
Do not dispose of product in a fire. The battery pack inside may explode or leak. Contact Fisher-Price®  
Consumer Relations at service.fisher-price.com or call 1-800-432-5437 to purchase a battery pack.  
• Never short-circuit the battery pack terminals.  
• Use only batteries of the same type, as recommended.  
Download from Www.Somanuals.co2m6. All Manuals Search And Download.  
Problems & Solutions  
Problem  
Solution  
No image on receiver screen  
Press the video screen on/off button. You can also change the  
voice activated setting to . The video screen automatically  
turns on when baby makes noise.  
Batteries in receiver are weak or dead. Use AC adaptor as power  
source and to charge the battery.  
Transmitter camera lens is obstructed. Adjust the camera  
angle on the transmitter.  
Receiver beeps and out of range Receiver is out of range of transmitter. Move receiver closer  
screen displays  
to transmitter.  
Note: Range varies depending on surrounding conditions such  
as noise levels, physical obstructions and signal interference.  
Under optimal conditions, the range is up to 400 feet.  
Transmitter power is off. Turn transmitter power on.  
Loose power cord connection and transmitter power is off.  
Check transmitter power cord plug-to-outlet connection.  
No power to wall outlet and transmitter power is off. Make sure  
light switch that controls power flow to wall outlet is on.  
Power is off because circuit breaker for room is off. Make sure  
house fuses and circuit breakers are on.  
Receiver power L.E.D.  
does not light  
Receiver power is off. Turn receiver power on.  
Battery pack in receiver is weak or dead. Use AC adaptor as  
power source and to charge the battery for four hours.  
Power is off because circuit breaker for room is off. Make sure  
house fuses and circuit breakers are on.  
No power to wall outlet and power is off. Make sure light switch  
that controls power flow to wall outlet is on.  
Download from Www.Somanuals.co2m7. All Manuals Search And Download.  
Problems & Solutions  
Problem  
Solution  
Receiver beeps and displays  
Battery pack in receiver is weak or dead. Use AC adaptor as  
low battery icon on screen power source and to charge the battery for four hours.  
Transmitter power L.E.D.  
does not light  
Transmitter power is off. Turn transmitter power on.  
Loose power cord connection and transmitter power is off.  
Check transmitter power cord plug-to-outlet connection.  
No power to wall outlet and transmitter power is off. Make sure  
light switch that controls power flow to wall outlet is on.  
Power is off because circuit breaker for baby’s room is off.  
Make sure house fuses and circuit breakers are on.  
You can hear conversations or  
sounds from other homes  
There is signal interference due to other nursery monitors on  
same channel or cordless telephone use. You may need to pair  
the receiver and transmitter. Remove the receiver battery door  
and press the pairing button with a paperclip. The power LED  
will blink when the pairing button is released. Then, turn over  
the transmitter and press the pairing button with a paperclip.  
The signal L.E.D. on the receiver will flash and you will hear  
a confirmation tone.  
Hint: If, after checking all of these solutions, you believe that your transmitter power cord or  
AC adaptor are damaged, please contact Fisher-Price®.  
Download from Www.Somanuals.co2m8. All Manuals Search And Download.  
FCC Statement (United States Only)  
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to  
part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful inter-  
ference in a residential installation. This equipment generates, uses and can radiate radio frequency energy  
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio  
communications. However, there is no guarantee that interference will not occur in a particular installation.  
If this equipment does cause harmful interference to radio or television reception, which can be determined  
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more  
of the following measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  
Consult the dealer or an experienced radio/TV technician for help.  
Note: Changes or modifications not expressly approved by the manufacturer responsible for compliance  
could void the user’s authority to operate the equipment.  
Video Monitor  
Model Number: N9326  
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:  
(1) This device may not cause harmful interference and (2) this device must accept any interference  
received, including interference that may cause undesired operation.  
Video Monitor  
Consumer Relations Department  
636 Girard Avenue  
East Aurora, New York 14052, U.S.A  
To maintain compliance with the FCC's RF exposure guidelines, place the transmitter at least 20 cm from users.  
Make sure the transmitter is not located near or operated along with any other antenna or transmitter.  
Download from Www.Somanuals.co2m9. All Manuals Search And Download.  
RSS-210 ICES-003 CNR-210 NMB-003  
RSS-210  
This device complies with RSS-210 of Industry Canada. Operation is subject to the following two  
conditions: (1) this device may not cause harmful interference and (2) this device must accept any  
interference received, including interference that may cause undesired operation.  
ICES-003  
This Class B digital apparatus complies with Canadian ICES-003. Operation is subject to the following  
two conditions: (1) this device may not cause harmful interference and (2) this device must accept any  
interference received, including interference that may cause undesired operation.  
CNR-210  
Ce dispositif est conforme au CNR-210 d’Industrie Canada. L’utilisation de ce dispositif est autorisée  
seulement aux conditions suivantes : (1) il ne doit pas produire de brouillage et (2) l’utilisateur du  
dispositif doit être prêt à accepter tout brouillage radioélectrique reçu, même si ce brouillage  
est susceptible de compromettre le fonctionnement du dispositif.  
NMB-003  
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. Cet appareil  
numérique de la classe B est conforme à la norme NMB-003 du Canada. L’utilisation de ce dispositif est  
autorisée seulement aux conditions suivantes : (1) il ne doit pas produire de brouillage et (2) l’utilisateur  
du dispositif doit être prêt à accepter tout brouillage radioélectrique reçu, même si ce brouillage est  
susceptible de compromettre le fonctionnement du dispositif.  
Download from Www.Somanuals.co3m0. All Manuals Search And Download.  
One (1) Year Limited Warranty (United States Only)  
Fisher-Price, Inc., 636 Girard Avenue, East Aurora, New York 14052 warrants to the original owner that this  
product is free from all defects in material and workmanship when used under normal conditions for  
a period of one (1) year from the date of purchase.  
Should the product fail to perform properly, we will repair or replace it at our option, free of charge.  
Purchaser is responsible for shipping the product to Consumer Relations at the address indicated above  
and for all associated freight and insurance cost. Fisher-Price, Inc. will bear the cost of shipping the  
repaired or replaced item to you. This warranty is void if the owner repairs or modifies the product. This  
warranty excludes any liability other than that expressly stated above including but not limited to any  
incidental or consequential damages.  
SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL  
DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.  
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH  
MAY VARY FROM STATE TO STATE.  
Care  
• Excess dirt in transmitter microphone will hamper transmission of sound. Wipe all parts with a damp  
cloth. Do not immerse any part of this monitor.  
Download from Www.Somanuals.co3m1. All Manuals Search And Download.  
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, New York 14052, U.S.A.  
©2008 Mattel, Inc. All Rights Reserved.  
® and ™ designate U.S. trademarks of Mattel, Inc  
PRINTED IN CHINA  
N9326a-0920  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Ernemann Projector E15 Series User Manual
ETA Systems Power Supply ETA S15 User Manual
FujiFilm All in One Printer 7750 User Manual
FujiFilm Digital Camera 16215853 User Manual
Fujitsu Laptop S6120D User Manual
Fujitsu Scanner C150 E194 01EN User Manual
Futrex Scale Futrex 5000 XL User Manual
GE Hot Beverage Maker 169040 User Manual
Global Technology Associates Kitchen Entertainment Center GB 2000X User Manual
Global Upholstery Co Indoor Furnishings Intensive Use and Multiple Shift User Manual