Bounce ’n Play Activity Dome
Model Number: 79534
Instructions
Please save these instructions for future reference.
Adult assembly is required.
Tool needed for assembly: Phillips Screwdriver.
Use only for a child who is unable to push up on hands and knees, pull up or sit unassisted.
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
Metal Canopy Stay
®
®
Pad
2 Covers
3 Toys
2 Base Wires
Base
Plastic Mesh Cover Stay
M6 x 13/8" Screw - 8
M5 x 113/16" Screw - 2
M6 Lock Nut - 8
M5 Lock Nut - 2
SHOWN ACTUAL SIZE
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
IMPORTANT! Before each use or assembly, inspect this product for damaged hardware, loose joints, missing parts or
sharp edges. DO NOT use if any parts are missing or broken. Contact Fisher-Price® for replacement parts and
instructions if needed. Never substitute parts.
Button Hole
Plastic Mesh
Cover Stay
3
1
Frame
Middle Hole
Middle Hole
Mesh Cover
Frame Tube
Frame Tube
Base
• Position the ends of the frame tubes against the
middle holes in a frame.
• Position the base upright on a flat surface.
• Locate the end of the base with the mesh cover. Insert
the entire plastic mesh cover stay into one of the
button holes in the mesh cover.
Hexagonal
Opening
4
• Be sure to tuck the plastic mesh cover stay away from
the button holes in both sides of the mesh cover.
M6 Lock Nut
Frame Tube
Canopy Tunnel
2
Metal
Base
Canopy
Stay
Frame
Tube
Frame
M6 x 13/8" Screw - 4
M6 Lock Nut - 4
• Insert an M6 x 13/8" screw through each frame tube
and into the frame.
• Fit an M6 lock nut into each corresponding hexagonal
opening on the back of the frame.
• Insert the metal canopy stay through the canopy tunnel.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
5
7
Metal Canopy Stay
Cover
Upper
Hole
• Tighten the screws with a Phillips screwdriver. Do not
over-tighten.
Slot
Tab
• Repeat this procedure to attach the other ends of the
frame tubes to the frame on the other side of the base.
Frame
M5 x 113/16" Screw - 2
M5 Lock Nut - 2
6
• Position one end of the metal canopy stay against the
upper hole in a frame.
Lower Hole
Base Wire
• Insert an M5 x 113/16" screw through the hole in
the cover.
• Fit the end of the screw through the hole in the metal
canopy stay and into the hole in the frame.
• Push on the cover to insert and“snap”the tab on
the cover into the slot in the frame. Make sure you
hear a “snap”.
• Fit an M5 lock nut into the corresponding hexagonal
opening on the back of the frame.
Lower Hole
Base Wire
• Tighten the screw with a Phillips screwdriver. Do not
over-tighten.
• Repeat this procedure to attach the other end of the
metal canopy stay and the remaining cover to the
frame on the other side of the base.
M6 x 13/8" Screw - 4
M6 Lock Nut - 4
• Position the base wires around the base so that the
ends point upward and are in front of the lower holes
in a frame.
• Insert an M6 x 13/8" screw through each base wire and
into the frame.
• Fit an M6 lock nut into each corresponding hexagonal
opening on the back of the frame.
• Tighten the screws with a Phillips screwdriver. Do not
over-tighten.
5
• Repeat this procedure to attach the other ends of the
base wires to the frame on the other side of the base.
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Use
To Unfold
Toys
8
Carry Straps
Canopy
Fasteners
1
Pad
Fastener
®
®
• Position the product on a flat surface.
• Unfasten the carry straps.
Base Fastener
• Lift the canopy.
• Fasten the pad fasteners to the base fasteners.
• Attach the toys to the canopy fasteners.
2
Assembly is now complete, but Bounce ‘n Play
Activity Dome is not ready for use. Please refer to
the Use instructions, page 7, steps 3 and 4.
Sides of Base Wire
• Grasp both sides of a base wire.
• Pull both sides of the base wire outward and then let
the base wire rotate down.
Note: If the base wire does not freely rotate down, pull
the sides of the base wire further outward.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Use
Using the Canopy
3
Canopy Down
5
Canopy Up
Frame
Groove
Groove
Base Wire
®
• Lift the product up slightly so that the base wire
“snaps”into the groove in each frame. Make sure
you hear a “snap”.
• Adjust the canopy up or down.
• Repeat Use Steps 2 and 3 to unfold the other base wire.
Using the Mesh Cover
Zipper
Mesh
Cover Up
4
Canopy Up
6
Frame
Groove
Base Wire
®
• Push down on the product to
be sure the base wires are in
the correct position.The base
wires should rest in the groove
in each frame.
• Adjust the canopy and mesh cover up.
• While holding the mesh cover up, fasten the
zipper closed.
Correct
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Use
To Fold for Portability
7
Use
Carry Straps
9
Frame
Groove
Groove
Base Wire
®
• Grasp both sides of a base wire.
• Fasten the carry straps.
• While lifting the product up slightly, pull both sides of
the base wire outward to remove the base wire from
the groove in each frame.
Care
Base Wire
The pad is machine washable.Wash the pad separately
in cold water on the gentle cycle. Do not use bleach.
Tumble dry separately on low heat and remove promptly.
The fabric, frame and toys may be wiped clean using a
mild cleaning solution and a damp cloth.
8
Correct
• Rotate the base wire up.
• Repeat this procedure to fold the other base wire.
If you have any questions about this product:
In CANADA: Mattel Canada Inc., 6155 Freemont Blvd., Mississauga, Ontario L5R 3W2.
Questions? 1-800-567-7724.
In GREAT BRITAIN: Mattel U.K., Ltd., Helpline: 01628 500302.
In AUSTRALIA: Mattel Australia Pty. Ltd., 658 Church Street, Locked Bag #870, Richmond,
Victoria 3121 Australia. Consumer Advisory Service 1-800-800-812 (valid only in Australia).
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A.
79534 B 79534-0920
©1998 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc.
Printed in Hong Kong
Download from Www.Somanuals.com. All Manuals Search And Download.
|