FMI Indoor Fireplace FMH26TN User Manual

COMPACT HEAT MAJIC™

VENT-FREE NATURAL GAS FIREPLACE SYSTEM

OWNER’S OPERATION AND INSTALLATION MANUAL

FMH26TN

14,000 to 26,000 Btu/Hr

with Thermostat

Shown with Optional

Cabinet Mantel/Hearth

Base Accessory

WARNING: Improper installa-

WARNING: If the information in this manual

tion,adjustment,alteration,ser-

is not followed exactly, a fire or explosion

vice,ormaintenancecancause

may result causing property damage, per-

sonal injury, or loss of life.

injury or property damage. Re-

fer to this manual for correct

— Do not store or use gasoline or other

flammable vapors and liquids in the

vicinity of this or any other appliance.

installationandoperationalpro-

cedures. For assistance or ad-

ditional information consult a

qualified installer, service

agency, or the gas supplier.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do

not use any phone in your building.

• Immediatelycallyourgassupplierfrom

a neighbor’s phone. Follow the gas

supplier’s instructions.

WARNING:Thisisanunvented

gas-fired heater. It uses air

(oxygen) from the room in

whichitisinstalled.Provisions

for adequate combustion and

ventilation air must be pro-

vided.RefertoAirforCombus-

tion and Ventilation section on

page 5 of this manual.

• If you cannot reach your gas supplier,

call the fire department.

— Installation and service must be per-

formed by a qualified installer, service

agency, or the gas supplier.

This appliance may be installed in an aftermarket*, permanently located, manufactured

(mobile) home, where not prohibited by local codes.

This appliance is only for use with the type of gas indicated on the rating plate. This

appliance is not convertible for use with other gases.

*Aftermarket: Completion of sale, not for purpose of resale, from the manufacturer

Save this manual for future reference.

Download from Www.Somanuals.com. All Manuals Search And Download.

OWNER’S MANUAL

SAFETY

PRODUCT

FEATURES

LOCAL CODES

INFORMATION

Install and use fireplace with care. Follow all

localcodes.Intheabsenceoflocalcodes,use

the latest edition of The National Fuel Gas

Code ANSI Z223.1/NFPA 54*.

Continued

SAFETY PILOT

14. Turn off and unplug fireplace and let

cool before servicing. Only a qualified

service person should service and re-

pair fireplace.

This fireplace has a pilot with an Oxygen

DepletionSensing(ODS)safetyshutoffsys-

tem. The ODS/pilot is a required feature for

vent-free room fireplaces. The ODS/pilot

shuts off the fireplace if there is not enough

fresh air.

*Available from:

American National Standards Institute, Inc.

1430 Broadway

15. Operating fireplace above elevations of

4,500 feet could cause pilot outage.

New York, NY 10018

National Fire Protection Association, Inc.

Batterymarch Park

16. Do not operate fireplace if any log is

broken. Do not operate fireplace if a

log is chipped (dime-sized or larger).

PIEZO IGNITION SYSTEM

This fireplace has a piezo ignitor. This sys-

tem requires no matches, batteries, or other

sources to light fireplace.

Quincy, MA 02269

17. Provide adequate clearances around air

openings.

UNPACKING

1. Remove log box and fireplace from

carton. The hood is not attached.

THERMOSTATIC HEAT

CONTROL

This fireplace has a thermostat sensing bulb

and a control valve. The thermostat will

automatically modulate the heat output to

maintain a consistent room temperature.

This results in greater fireplace comfort.

This can also result in lower gas bill.

IMPORTANT: The fireplace hood is

inside the cardboard protective end

wrap on the left side of fireplace (as

viewed from front). A decal is on the

outside of the cardboard end wrap stat-

ing hood is enclosed (see Figure 2).

2. Remove hood from cardboard protec-

tive end wrap as shown in Figure 2.

3. Remove all protective packaging ap-

plied to fireplace for shipment.

PRODUCT IDENTIFICATION

Fireplace

Cabinet

4. Make sure your fireplace includes one

hardware packet.

5. Check fireplace for any shipping

damage. If fireplace is damaged,

promptly inform dealer where you

bought fireplace.

IMPORTANT:

THIS PACKAGE CONTAINS A

Hood

Screen

FIREPLACE HOOD. UNWRAP

CARTON AND REMOVE HOOD

BEFORE DISCARDING

PROTECTIVE PACKAGING.

Enclosed

Decal

Cardboard

Protective

Fireplace

End Wrap

Logs

Control Knob

Ignitor Button

Hood

Figure 1 - Vent-Free Natural Gas Fireplace System

Figure 2 - Removing Fireplace Hood

107105

Download from Www.Somanuals.com. All Manuals Search And Download.

NATURAL GAS VENT-FREE FIREPLACE SYSTEM

Log

Screen

Shipping

Screw

ASSEMBLY

Shoulder

Screw

WARNING: Always have

branch support and screen in

place before operating fireplace.

Thispreventsexcessivetempera-

tures on fireplace surfaces.

Burner

Support

WARNING: Failure to position

thepartsinaccordancewiththese

diagrams or failure to use only

parts specifically approved with

this fireplace may result in prop-

erty damage or personal injury

ASSEMBLING FIREPLACE

Tools Required:

• Phillips screwdriver

• 5/16" hex wrench

• slotted screwdriver

Branch

Support

Screen

Installing Log

1. Lift screen up and pull out to remove.

2. Cut two plastic straps to remove the log

from the firebox cavity.

Figure 3 - Assembling Fireplace

3. An optional blower is available. See Ac-

cessories, page 26. Install optional

blower now. Follow installation in-

structions provided with blower.

4. Gently rotate hood to upright position.

Make sure hood tabs are behind lou-

vers and hood is resting on firebox top

(see Figure 4).

Assembling Hood

1. Locate four black phillips sheet metal

screws from the hardware packet.

2. Rotate hood as shown in Figure 4.

Make sure hood tabs point toward

fireplace.

4. Remove log packaging material and

discard packaging. Gently place log set

on burner support (see Figure 3). The

log should fit flat against top of burner

support and log locators fit into the slots

under the log. Do not allow log to con-

tact flame. If flame contacts log, soot

will be created.

5. Align screw holes on hood with screw

holes on firebox top.

6. Insert screws as shown in Figure 4.

Tighten screws firmly.

3. Insert hood tabs between baffle and

louvers (see Figure 4).

Louver

Hood

Tabs

Hood Tab

5. Reattach screen by placing the notches

in the screen frame over the shoulder

screws and pushing down.

Baffle

Sheet

Metal

Screw

Firebox Top

Figure 4 - Assembling Hood

107105

Download from Www.Somanuals.com. All Manuals Search And Download.

OWNER’S MANUAL

Confined and Unconfined Space

PROVIDING ADEQUATE

VENTILATION

AIR FOR

The National Fuel Gas Code, ANSI Z223.1/

NFPA54definesaconfinedspaceasaspace

whose volume is less than 50 cubic feet per

1,000 Btu per hour (4.8 m³per kw) of the

aggregate input rating of all appliances in-

stalledinthatspaceandanunconfinedspace

as a space whose volume is not less than 50

cubic feet per 1,000 Btu per hour (4.8 m³per

kw) of the aggregate input rating of all

appliances installed in that space. Rooms

communicating directly with the space in

whichtheappliancesareinstalled*,through

openings not furnished with doors, are con-

sidered a part of the unconfined space.

COMBUSTION AND

VENTILATION

The following are excerpts from National

FuelGasCode, ANSIZ223.1/NFPA54, Sec-

tion5.3, AirforCombustionandVentilation.

WARNING: This heater shall

notbeinstalledinaconfinedspace

or unusually tight construction

unless provisions are provided

foradequatecombustionandven-

tilation air. Read the following in-

structions to insure proper fresh

air for this and other fuel-burning

appliances in your home.

All spaces in homes fall into one of the three

following ventilation classifications:

1. Unusually Tight Construction

2. Unconfined Space

3. Confined Space

The information on pages 5 through 7 will

help you classify your space and provide

adequate ventilation.

Today’s homes are built more energy effi-

cient than ever. New materials, increased

insulation, and new construction methods

helpreduceheatlossinhomes.Homeowners

weather strip and caulk around windows and

doorstokeepthecoldairoutandthewarmair

in. During heating months, home owners

want their homes as airtight as possible.

* Adjoining rooms are communicating only

iftherearedoorlesspassagewaysorventila-

tion grills between them.

Unusually Tight Construction

The air that leaks around doors and win-

dows may provide enough fresh air for

combustion and ventilation. However, in

buildings of unusually tight construction,

you must provide additional fresh air.

Unusually tight construction is de-

fined as construction where:

While it is good to make your home energy

efficient, your home needs to breathe. Fresh

air must enter your home. All fuel-burning

appliances need fresh air for proper com-

bustion and ventilation.

a. walls and ceilings exposed to the

outside atmosphere have a con-

tinuous water vapor retarder with

a rating of one perm (6 x 10^-11kg

per pa-sec-m²) or less with open-

ings gasketed or sealed and

Exhaustfans, fireplaces, clothesdryers, and

fuel burning appliances draw air from the

house to operate. You must provide ad-

equate fresh air for these appliances. This

will insure proper venting of vented fuel-

burning appliances.

b. weather stripping has been

added on openable windows and

doors and

c. caulking or sealants are applied

to areas such as joints around

window and door frames, be-

tween sole plates and floors, be-

tween wall-ceiling joints, be-

tween wall panels, at penetra-

tions for plumbing, electrical, and

gas lines, and at other openings.

If your home meets all of the three

criteria above, you must provide ad-

ditional fresh air. See Ventilation Air

From Outdoors, page 7.

If your home does not meet all of the

three criteria above, proceed to De-

termining Fresh-Air Flow For Fire-

place Location, page 6.

Continued

107105

Download from Www.Somanuals.com. All Manuals Search And Download.

NATURAL GAS VENT-FREE FIREPLACE SYSTEM

AIR FOR

COMBUSTION AND

VENTILATION

Continued

DETERMINING FRESH-AIR FLOW FOR FIREPLACE LOCATION

Determining if You Have a Confined or Unconfined Space

Use this worksheet to determine if you have a confined or unconfined space.

Space: Includes the room in which you will install fireplace plus any adjoining rooms with doorless passageways or ventilation grills

between the rooms.

1. Determine the volume of the space (length x width x height).

Length x Width x Height = _________________cu. ft. (volume of space)

Example: Space size 20 ft. (length) x 16 ft. (width) x 8 ft. (ceiling height) =2560 cu. ft. (volume of space)

If additional ventilation to adjoining room is supplied with grills or openings, add the volume of these rooms to the total volume of

the space.

2. Multiply the space volume by 20 to determine the maximum Btu/Hr the space can support.

_____________________(volume of space) x 20 = (Maximum Btu/Hr the space can support)

Example: 2560 cu. ft. (volume of space) x 20 = 51,200 (maximum Btu/Hr the space can support)

3. Add the Btu/Hr of all fuel burning appliances in the space.

Vent-free fireplace

Gas water heater*

Gas furnace

Vented gas heater

Gas fireplace logs

__________________Btu/Hr

Example:

30,000

26,000

56,000

Gas water heater

Vent-free fireplace +

Btu/Hr

Total

Other gas appliances* + __________________Btu/Hr

Total = __________________Btu/Hr

* Do not include direct-vent gas appliances. Direct-vent draws combustion air from the outdoors and vents to the outdoors.

4. Compare the maximum Btu/Hr the space can support with the actual amount of Btu/Hr used.

_________________ Btu/Hr (maximum the space can support)

_________________ Btu/Hr (actual amount of Btu/Hr used)

Example: 51,200 Btu/Hr (maximum the space can support)

56,000 Btu/Hr (actual amount of Btu/Hr used)

The space in the above example is a confinedspace because the actual Btu/Hr used is more than the maximum Btu/Hr the space cansupport.

You must provide additional fresh air. Your options are as follows:

A. Rework worksheet, adding the space of an adjoining room. If the extra space provides an unconfined space, remove door to adjoin-

ing room or add ventilation grills between rooms. See Ventilation Air From Inside Building, page 7.

B. Vent room directly to the outdoors. See Ventilation Air From Outdoors, page 7.

C. Install a lower Btu/Hr fireplace, if lower Btu/Hr size makes room unconfined.

If the actual Btu/Hr used is less than the maximum Btu/Hr the space can support, the space is an unconfined space. You will need no

additional fresh air ventilation.

WARNING:If the area in which the heater may be operated is smaller than that defined as an unconfined space

or if the building is of unusually tight construction, provide adequate combustion and ventilation air by one of

themethodsdescribedintheNationalFuelGasCode,ANSIZ223.1/NFPA54,Section5.3orapplicablelocalcodes.

107105

Download from Www.Somanuals.com. All Manuals Search And Download.

OWNER’S MANUAL

AIR FOR

COMBUSTION AND

VENTILATION

12"

Continued

VENTILATION AIR

Ventilation Air From Inside

Building

Ventilation Grills

Into Adjoining Room,

Option 2

Ventilation

Grills

Thisfreshairwouldcomefromanadjoining

unconfined space. When ventilating to an

adjoining unconfined space, you must pro-

vide two permanent openings: one within

12" of the ceiling and one within 12" of the

floor on the wall connecting the two spaces

(see options 1 and 2, Figure 5). You can also

remove door into adjoining room (see op-

tion 3, Figure 5). Follow the National Fuel

Gas Code, ANSI Z223.1/NFPA 54, Section

5.3, Air for Combustion and Ventilation for

required size of ventilation grills or ducts.

into Adjoining

Room,

Option 1

Remove

Door into

Adjoining

Room,

Option 3

12"

Ventilation Air From Outdoors

Provide extra fresh air by using ventilation

grills or ducts. You must provide two per-

manent openings: one within 12" of the

ceiling and one within 12" of the floor.

Connect these items directly to the outdoors

orspacesopentotheoutdoors.Thesespaces

include attics and crawl spaces. Follow the

NationalFuelGasCode,ANSIZ223.1/NFPA

54, Section 5.3, Air for Combustion and

Ventilation for required size of ventilation

grills or ducts.

Figure 5 - Ventilation Air from Inside Building Shown with Optional Mantel

Ventilated

Outlet

Attic

Air

IMPORTANT: Do not provide openings for

inlet or outlet air into attic if attic has a

thermostat-controlledpowervent.Heatedair

enteringtheatticwillactivatethepowervent.

Outlet

Air

To Attic

Crawl

Space

Inlet

Air

Ventilated

Inlet Air

Crawl Space

Figure 6 - Ventilation Air from Outdoors Shown with Optional Mantel

107105

Download from Www.Somanuals.com. All Manuals Search And Download.

NATURAL GAS VENT-FREE FIREPLACE SYSTEM

CEILING

Note: Your vent-free fireplace is designed

to be used in zero clearance installations.

Wall or framing material can be placed

directly against any exterior surface on the

rear, sides, or top of your fireplace, except

where stand-off spacers are integrally at-

tached. If standoff spacers are attached to

your fireplace, these spacers can be placed

INSTALLATION

NOTICE: This heater is intended

foruseassupplementalheat.Use

this heater along with your pri-

mary heating system. Do not in-

stall this heater as your primary

heat source. If you have a central

heating system, you may run

36"

Minimum

From

Sides Of

Fireplace

directly against wall or framing materials.

system’scirculatingblowerwhile

using heater. This will help circu-

late the heat throughout the

house. In the event of a power

outage, you can use this heater

as your primary heat source.

Use the dimensions shown for rough open-

ings to create the easiest installation (see

Built-In Fireplace Installation, page 9).

Left

Side

Right

Side

CHECK GAS TYPE

Use only natural gas. If your gas supply is

not natural gas, do not install fireplace. Call

dealerwhereyouboughtfireplaceforproper

type fireplace.

FLOOR

0" Minimum To Top Surface Of Carpeting,

Tile Or Other Combustible Material

WARNING: A qualified ser-

vicepersonmustinstallfireplace.

Follow all local codes.

Figure7-MountingClearancesAsViewed

From Front of Fireplace Shown Built In

The Wall

INSTALLATION ITEMS

Before installing fireplace, make sure you

have the items listed below.

CEILING

WARNING: Never install the

fireplace

• piping (check local codes)

• sealant (resistant to propane/LP gas)

• equipment shutoff valve *

• test gauge connection *

• ground joint union

• sediment trap

Top Of

Mantel Can

• in a bedroom or a bathroom

• in a recreational vehicle

• where curtains, furniture,

clothing, or other flammable

objectsarelessthan36inches

from the front, top, or sides of

the fireplace

• as a fireplace insert

• in high traffic areas

• in windy or drafty areas

36"

Be Flush

Minimum

With Wall

• tee joint

• pipe wrench

* ACSAdesign-certifiedequipmentshutoff

valve with 1/8" NPT tap is an acceptable

alternative to test gauge connection. Pur-

chase the optional CSA design-certified

equipment shutoff valve from your dealer.

See Accessories, page 26.

Right

Side

Left

Side

CAUTION: This fireplace cre-

ates warm air currents. These

currents move heat to wall sur-

faces next to fireplace. Installing

fireplace next to vinyl or cloth

wall coverings or operating fire-

place where impurities (such as,

butnotlimitedto,tobaccosmoke,

aromatic candles, cleaning flu-

ids,oilorkerosenelamps,etc.)in

the air exist, may discolor walls

or cause odors.

Note:Ifdesired,purchaseafour-sidedbrass

trim kit for built-in installations. See Acces-

sories, page 26.

0" Minimum To Top Surface Of Carpeting,

Tile Or Other Combustible Material

Figure8-MountingClearancesAsViewed

From Front of Fireplace Shown with

Optional Mantel

LOCATING FIREPLACE

WARNING:Maintainthemini-

mum clearances shown in Fig-

ures 7 and 8. If you can, provide

greater clearances from floor,

ceiling, and joining wall.

Note: When installing fireplace directly on

carpeting, tile or other combustible material,

other than wood flooring, the fireplace shall

beinstalledonametalorwoodpanelextend-

ing the full width and depth of the fireplace

IMPORTANT:Vent-freefireplacesaddmois-

ture to the air. Although this is beneficial,

installing fireplace in rooms without enough

ventilationairmaycausemildewtoformfrom

too much moisture. See Air for Combustion

and Ventilation, pages 5 through 7.

You can recess firebox into the wall. You

can also position fireplace in the optional

cabinet or corner mantels. IMPORTANT:

Only use optional cabinet or corner mantels

specified in this manual. Purchase the op-

tional mantel from your dealer (see Acces-

sories, page 26).

CAUTION: If you install the

fireplace in a home garage

• fireplace pilot and burner must

beatleast18inchesabovefloor.

• locate fireplace where moving

vehicle will not hit it.

107105

Download from Www.Somanuals.com. All Manuals Search And Download.

OWNER’S MANUAL

9. Check all gas connections for leaks. See

INSTALLATION

WARNING: If pre-wiring, do

not connect wiring to any electri-

cal source at this time.

Checking Gas Connections, page 16.

Continued

10. If using optional brass trim kit, install

the trim after final finishing and/or

painting of wall. See instructions in-

cluded with brass trim accessory for at-

taching brass trim.

For convenience and efficiency, install

fireplace

Install fireplace electrical outlet

and connect wiring to outlet be-

fore connecting to electrical

source. The fireplace electrical

outlet is included with the

GA3450(T) blower accessory.

• where there is easy access for operation,

inspection, and service.

IMPORTANT: When finishing your fire-

box,combustiblematerialssuchaswallboard,

gypsumboard,sheetrock,drywall,plywood,

etc. maybebuttedupnexttothesidesandtop

of the firebox. Combustible materials should

never overlap the firebox front facing.

• in coldest part of room.

An optional blower kit is available from

your dealer. See Accessories, page 26. If

planningtouseblower,locatefireplacenear

an electrical outlet.

Only use the fireplace electrical

outlet supplied with the

GA3450(T) blower accessory.

BUILT-IN FIREPLACE

INSTALLATION

Note:Aqualified installer should make

all electrical connections.

WARNING: Do not allow any

combustiblematerialstooverlap

the firebox front facing.

3. Install gas piping to fireplace location.

This installation includes an approved

flexible gas line (if allowed by local

codes) after the equipment shutoff

valve. The flexible gas line must be the

last item installed on the gas piping.

Built-ininstallationofthisfireplaceinvolves

installing fireplace into a framed-in enclo-

sure. This makes the front of fireplace flush

with wall. An optional brass trim kit acces-

sory is available (see Accessories, page 26).

Brasstrimwillextendpastsidesoffireplace

approximately 1/2 inch. This will cover the

rough edges of the wall opening. If install-

ingabuilt-inmantelabovethefireplaceyou

must follow the clearances shown in Figure

12, page 10. Follow the instructions below

to install the fireplace in this manner.

IMPORTANT: Noncombustible materials

such as brick, tile, etc. may overlap the front

facing, but should never cover any neces-

sary openings like louvered slots.

4. If you have not assembled firebox, fol-

low instructions on page 4.

WARNING: Do not allow non-

combustible materials to cover

any necessary openings like lou-

vered slots.

5. Carefully set fireplace in front of rough

opening with back of fireplace inside

wall opening.

6. Attach flexible gas line to fireplace gas

regulator. See Connecting Fireplace to

Gas Supply, page 15.

Actual Framing

WARNING: Never modify or

cover the louvered slots on the

front of the firebox.

Height

26"

26 ³/4"

9 ¹/2"

3/4"

26 ⁷/8"

10 ¹/2"

3/4"

7. Bend four nailing flanges on outer cas-

ing with pliers (see Figure 11).

Front Width

Depth

8. Attach fireplace to wall studs using

nails or wood screws through holes in

nailing flange.

WARNING: Use only noncom-

bustiblemortaroradhesiveswhen

overlapping the front facing with

noncombustible facing material.

Bottom

1. Frame in rough opening. Use dimen-

sions shown in Figure 9 for the rough

opening.

If installing in a corner, use dimensions

shown in Figure 10 for the rough open-

ing. The height is 26 ⁷/8" which is the

same as the wall opening above.

10 ¹

/2"

Nails or

Wood

Screws

26⁷

/8"

3/4" Off

2. If installing GA3450(T) blower acces-

sory, do so at this time. Follow instruc-

tions included with blower accessory.

The Floor

Minimum

26⁷

/8"

Figure9-RoughOpeningforInstallingin

Wall

Note: If not installing blower acces-

sory, you may wish to run electrical

wiring to your fireplace for future

blower installation (see Accessories,

page 26) Use only approved three-wire

electrical wiring.

36⁵

25⁷

Nailing

Flanges

26⁷

51³

Figure 10 - Rough Opening for Installing

in Corner

Figure11-AttachingFireplacetoWallStuds

Continued

107105

Download from Www.Somanuals.com. All Manuals Search And Download.

NATURAL GAS VENT-FREE FIREPLACE SYSTEM

3. Place mantel around fireplace/base 12. Check for leaks. See Checking Gas

INSTALLATION

assembly.

4. Assemble brass trim kit. See Assem- 13. Place mantel around fireplace. Be care-

bling Brass Trim, page 11. ful not to damage wall or mantel.

5. Firmly snap brass trim kit on shoulder 14. Place brass trim kit on the shoulder

Connections, page 16.

Continued

Mantel Clearances for Built-In

Installation

If placing mantel above built-in fireplace,

youmustmeetminimumclearancebetween

mantel shelf and top of fireplace opening.

screws. Shoulder screws are located on

fireplace cabinet (see Figure 13).

screws located on the side and top of

the fireplace. Firmly snap the brass trim

over the shoulder screws on fireplace

(see Figure 13).

6. Align brass trim kit for flush fit around

opening.

NOTICE:Surfacetemperaturesof

adjacent walls and mantels be-

comehotduringoperation.Walls

and mantels above the firebox

may become hot to the touch. If

installedproperly,thesetempera-

turesmeettherequirementofthe

national product standard. Fol-

low all minimum clearances

shown in this manual.

15. Adjust assembly to remove any gaps.

Attach remaining two 3" wood screws

from hardware pack through openings

inside of fireplace sides into the man-

tel. The openings are located at top be-

hind the area for the black louvers (see

Figure 13).

7. Use two 3" wood screws provided and

attach fireplace base to wooden base

(see Figure 13).

8. Remove brass trim kit and mantel. Be

careful not to damage wall or mantel.

9. Place wood base next to wall at instal-

lation location.

16. Reinstall top black louvers.

10. Attach wood base to floor with two 1 ³/4"

black screws provided (see Figure 14).

If the floor is concrete use anchor method

(see AttachingWood Base to Solid Floor,

page 14).

Hole for 3"

wood screw

Shoulder

Screws

for attaching

fireplace to

mantel

NOTICE: If your installation does

notmeettheminimumclearances

shown, you must do one of the

following:

11. Install gas line. See Connecting To Gas

Supply, page 14.

Mantel Shelf

• raise the mantel to an accept-

able height

• remove the mantel

10"

Note:

All vertical

measurements

are from top of

fireplace

2 ¹/2

OPTIONAL MANTEL

INSTALLATION

opening to

Note: Refer to instructions provided with

the mantel for assembly instructions. Refer

to instructions below for system installa-

tion. Refer to instructions on page 4 for

firebox assembly. Blower accessory should

be installed if it is being used (see Accesso-

ries, page 26).

bottom of

Hole for 3"

mantel shelf. All

measurements

are in inches.

wood screw

for attaching

fireplace to

wooden base

Assembled

Brass Trim

Side of

Firebox

Figure 13 - Attaching Brass Trim to

Fireplace

1. Unscrew four brass screws that attach

top louver to fireplace. Remove louver

from fireplace and set aside.

1 ³/4" Screw

2. Place fireplace on wood base.

Wood Base

Figure 12 - Minimum Mantel Clearances

for Built-In Installation

Figure 14 - Attaching Wood Base to Floor

107105

Download from Www.Somanuals.com. All Manuals Search And Download.

OWNER’S MANUAL

Branch

Support

INSTALLING BLOWER

ACCESSORY GA3450T

INSTALLATION

Shoulder

Screw

Continued

Removing Upper Louver

Assembly

Assembling Brass Trim (Brass

trim shipped with mantel)

Remove

Screw

1. Remove packaging from three remain-

ing pieces of brass trim.

To install the blower accessory, you must

first remove the upper louver assembly.

Valve

Cover

Shield

2. Locate two adjusting plates with set 1. Lift screen off heater.

screws, and two shims in the hardware

2. Remove 4 screws from louver assem-

packet.

bly (see Figure 16). Save these screws.

3. Align shim under adjusting plate as

shown in Figure 15.

3. Pull louver assembly straight out from

the cabinet. Be careful not to scratch

the paint. Set louver assembly and

4. Slide one end of adjusting plate/shim

in slot on mitered edge of top brass trim

(see Figure 15).

screws aside.

Blower Bracket

Mounting Holes

5. Slide other end of adjusting plate/shim

in slot on mitered edge of side brass

trim (see Figure 15).

Bottom Louver

Assembly

Snap

Bushings

6. While firmly holding edges of brass

trim together, tighten both set screws

on the adjusting plate with slotted

screwdriver.

Figure 17 - Removing Valve Cover Shield

Installing Blower Assembly

7. Repeat steps 1 through 6 for other corner.

Upper Louver

Assembly

CAUTION: Label all wires

priortodisconnectionwhenser-

vicing controls. Wiring errors

can cause improper and danger-

ous operation.

8. Set brass assembly aside for later in-

stallation.

Brass Screws

Top Brass

Figure 16 - Removing Upper Louver

Assembly

Trim

Set

Screws

Slot

Removing Valve Cover Shield

CAUTION: Verify proper op-

eration after servicing.

1. Open bottom louver assembly by

swinging the assembly down (see Fig-

ure 17).

Mitered

Edge

Note: If you are using a mantel with your

heater, use the following instructions. If

your heater is built-in, see For Built-In In-

stallation on page 13.

Shim

2. Using short Phillips screwdriver, re-

move the screw under the center of the

branch support. Rotate valve cover

shield clockwise and slide out.

IMPORTANT: Do not remove shoul-

der screw on the left side of valve cover

shield. Slide the valve cover shield off

of the shoulder screw (see Figure 17).

Side Brass

Trim

Adjusting

Plate

1. Install snap bushings found in hardware

kit into both holes in rear of valve cover

shield.

Slot

2. Make sure the wire harness is firmly

connected to the terminals on the blower

bracket assembly.

Note: If you do not have a short

Phillips screwdriver, the screen, twigs,

and branch support must be removed

so a longer screwdriver may be used.

See Connecting Fireplace To Gas Sup-

ply, page 15 and follow step 2.

Figure 15 - Assembling Brass Trim

3. Note the wire locations on back of

AUTO/OFF/ON switch. The terminals

on back of switch are numbered 1, 2,

and 3. Carefully remove red wire from

terminal 1 and blue wire from terminal

3. Black wire can remain on middle

terminal 2 (see Figure 18, page 12).

Continued

107105

Download from Www.Somanuals.com. All Manuals Search And Download.

NATURAL GAS VENT-FREE FIREPLACE SYSTEM

6. Route the wire harness through the 9. Install the switch plate on the valve

INSTALLATION

hole in left side of baffle. Pull wire

harness through lower opening above

where the valve shield was removed.

(see Figure 18).

cover shield with 2 #10 screws provided

(see Figure 19). Reinstall the valve

cover shield. Route power cord out of

the cabinet by inserting it through the

bushing on the outer casing (see Fig-

ure 18). Plug fan kit into 120-Volt

grounded power supply and test opera-

tion. Note: When switch is in the

AUTO position, the fan will start after

the heater has run for a few moments.

The fan will continue to run for sev-

eral moments after the heater has been

turned off. When switch is in the ON

position, the fan will run until turned

to OFF. Reinstall upper louver assem-

bly and hood if previously removed,

(see Figure 16, page 11). Close lower

louver door.

Continued

4. Carefully disconnect green and white

wires at their insulated connectors.

7. Insert the 4 wire harness into one of the

round holes in the rear of the valve cover

shield and through the rectangular hole

in the front of shield (see Figure 18).

5. In top of the heater cabinet, locate the

four mounting holes on the outer cas-

ing. Align these four holes with those

on the blower bracket assembly. Attach

blower bracket assembly to the outer

casing with 4 #10 screws provided (see

Figure 18).

8. Reconnect red wire to switch position

3. Reconnect blue wire to switch posi-

tion 1. Reconnect green and white wires.

Wiring Routing

Hole in Baffle

Blower Bracket

Assembly

Screw

Baffle

Valve Cover

Shield

Wire

Harness

Switch

Plate

Power

Cord

Screw

Figure19-InstallingSwitchPlatetoValve

Cover Shield

Red

Blue

Switch

Plate

Wire

Harness

Valve Cover

Shield

Box Cover

Figure 18 - Installing Blower Bracket Assembly

107105

Download from Www.Somanuals.com. All Manuals Search And Download.

OWNER’S MANUAL

Fan Switch

INSTALLATION

(Auto/Off/On)

Auto

Continued

Off

Thermostat

Switch

(N.O.)

Blue

For Built-In Installation

WARNING: A licensed elec-

trician must connect the wiring

harness to electrical supply fol-

lowing all local codes. Electri-

cian must provide a clamp on

the box cover to secure the wir-

ing. Wiring should be routed

through the bushing in the hole

on the outer casing of heater.

Blue

110/115

V.A.C.

Red

Blower

Motor

Black

Red

White

Green

White

Green

Figure 20 - Wiring Diagram For Blower Accessory Built-In Installation

Follow instructions Removing Valve Cover

Shield (page 11), then

Blower Bracket

Assembly

1. Install a snap bushing found in hardware

kit into one of the holes found on rear of

valve cover shield. The other hole is for

a strain relief clamp (not supplied) to

secure incoming electrical supply.

Screw

2. Follow steps 2 through 6 in Installing

Blower Assembly, pages 11 and 12.

Also remove black wire from middle

switch terminal 2.

3. Remove black plastic strain relief and

power cord from switch plate. The

power cord supplied will not be used in

built-in installations. Pop in the plastic

snap bushing found in hardware kit into

the hole left by supply cord/strain relief.

Switch

Wire

Harness

Power

Cord

Outlet

Receptacle

4. A licensed electrician must follow the

wiring diagram to connect incoming

electrical supply to fan kit wiring har-

ness (see Figure 20).

Red

Blue

5. Plug power cord to the outlet receptacle

(not provided) as shown in Figure 21.

Wind the extra cable in power cord and

and tie it up with the plastic wire strap

(see Figure 21). Set the cable bundle

between the burner bracket and outer

casing, away from the burner.

Switch Plate

Plastic Wire

Strap

Valve

Cover

Shield

6. Reinstall valve cover shield.

Box Cover

Wire

7. Test to make sure the blower is work-

ing properly.

Harness

Clamp Connector

(not included)

8. Reinstall upper louver assembly and

hood if previously removed, (see Figure

16, page 11). Close lower louver door.

Figure 21 - Installing Blower Bracket Assembly

Continued

107105

Download from Www.Somanuals.com. All Manuals Search And Download.

NATURAL GAS VENT-FREE FIREPLACE SYSTEM

CONNECTING TO GAS

INSTALLATION

CAUTION:Use only new,

SUPPLY

Continued

black iron or steel pipe. Inter-

nally-tinned copper tubing may

be used in certain areas. Check

your local codes. Use pipe of

1/2" or greater diameter to al-

low proper gas volume to fire-

place. If pipe is toovolumepres-

sure will occur.

WARNING: This appliance re-

quires a 45° male flare fitting 5/8"-

18 UNF (Unified National Fine

Thread) inlet connection and the

flexible gas line provided.

Extension Cord

Use extension cord if needed. The cord must

have a three-prong, grounding plug and a

three-hole receptacle. Make sure cord is in

good shape. It must be heavy enough to carry

the current needed. An undersized cord will

cause a drop in line voltage. This will result

in loss of power and overheating. Use a No.

16 AWG cord for lengths less than 50 feet.

WARNING: A qualified ser-

vice person must connect fire-

place to gas supply. Follow all

local codes.

Installation must include an equipment

shutoff valve, union, and plugged 1/8" NPT

tap. Locate NPT tap within reach for test

gauge hook up. NPT tap must be upstream

from fireplace (see Figure 23).

Attaching Wood Base to Solid

Floor

IMPORTANT: Install main gas valve

(equipment shutoff valve) in an accessible

location. The main gas valve is for turning

on or shutting off the gas to the appliance.

WARNING: Never connect

fireplace to private (non-utility)

gas wells. This gas is commonly

known as wellhead gas.

For attaching base to solid floors (concrete

or masonry)

Note: Floor anchors and mounting screws

are in hardware package. The hardware

package is provided with fireplace.

Check your building codes for any special

requirementsforlocatingequipmentshutoff

valve to fireplaces.

IMPORTANT: Check gas line pressure be-

fore connecting fireplace to gas line. Gas

line pressure must be no greater than 14

1. Drill holes at marked locations using

5/16" drill bit. For solid floors (con- inchesofwater.Ifgaslinepressureishigher,

crete or masonry), drill at least 1" deep. fireplace regulator damage could occur.

ApplypipejointsealantlightlytomaleNPT

threads. This will prevent excess sealant

from going into pipe. Excess sealant in pipe

could result in clogged fireplace valves.

2. Fold floor anchor as shown in Figure 22.

CSA Design-Certified

3. Insert floor anchor (wings first) into

hole. Tap anchor flush to floor.

Equipment Shutoff Valve

With 1/8" NPT Tap*

CAUTION:Usepipejointseal-

ant that is resistant to liquid pe-

troleum (LP) gas.

4. Insert mounting screws through base

and into floor anchors.

5. Tighten screws until base is firmly fas-

tened to floor.

We recommend that you install a sediment

trap in supply line as shown in Figure 23.

Locate sediment trap where it is within

reach for cleaning. Install in piping system

betweenfuelsupplyandheater.Locatesedi-

ment trap where trapped matter is not likely

to freeze. A sediment trap traps moisture

and contaminants. This keeps them from

going into fireplace controls. If sediment

trap is not installed or is installed wrong,

fireplace may not run properly.

From Gas

Meter (5"

W.C. to

10.5" W.C.

Pressure)

3" Minimum

Cap Pipe Tee

Figure 22 - Folding Anchor

Nipple Joint

Sediment Trap

Figure 23 - Gas Connection

* Purchase the optional CSA design-certified

equipment shutoff valve from your dealer. See

Accessories, page 26.

107105

Download from Www.Somanuals.com. All Manuals Search And Download.

OWNER’S MANUAL

5. Check all gas connections for leaks. See

INSTALLATION

CAUTION: Avoid damage to

Checking Gas Connections, page 16.

Continued

regulator.Holdgasregulatorwith

wrenchwhenconnectingittogas

piping and/or fittings.

6. Replace branch support back into fire-

place. Feed flexible gas line into fire-

place base area while replacing branch

support. Make sure the entire flexible

gas line is in fireplace base area. Reat-

tach branch support to fireplace with

screws removed in step 2.

CONNECTING EQUIPMENT

SHUTOFF VALVE TO

HEATER CONTROL

4. Apply pipe joint sealant lightly to male

threads of gas connector attached to

flexible gas line/equipment shutoff

valve (see Figure 25).

Installation Items Needed

• Phillips screwdriver

• sealant (resistant to propane/LP gas, not

provided)

Screen

Shipping

Screw

1. Remove fireplace screen. Remove two

screws that hold fireplace screen in

place for shipping. These screws are

located near top of screen. Discard

screws. Lift fireplace screen up and pull

out to remove.

Branch

Support

Shoulder

Screw

2. Remove screws that attach branch sup-

port to fireplace (see Figure 24). Care-

fully lift up branch support and remove

from fireplace (see Figure 24).

Flexible

Gas Line

3. Route flexible gas line, included, from

fireplace control to equipment shutoff

valve through side or rear access holes

in outer casing.

NOTICE: Most building codes do

not permit concealed gas con-

nections. A flexible gas line is

provided to allow accessibility

fromthefireplace(seeFigure25).

The flexible gas supply line con-

nection to the equipment shutoff

valve should be accessible.

Screen

Figure 24 - Removing Branch Support From Fireplace

To Fireplace

Gas Regulator

Equipment Shutoff Valve

Provided by Installer

Flexible Gas Line from

Fireplace Gas Regulator

To External

Regulator

Figure 25 - Attaching Flexible Gas Line to Equipment Shutoff Valve

Continued

107105

Download from Www.Somanuals.com. All Manuals Search And Download.

NATURAL GAS VENT-FREE FIREPLACE SYSTEM

Test Pressures Equal To or Less Than

1/2 PSIG (3.5 kPa)

Pressure Testing Fireplace Gas

Connections

1. Open equipment shutoff valve (see Fig-

INSTALLATION

Continued

1. Close equipment shutoff valve (see Fig-

ure 26).

CHECKING GAS

CONNECTIONS

2. Pressurize supply piping system by either

2. Open main gas valve located on or near

gas meter.

using compressed air or opening main gas

valve located on or near gas meter.

3. Make sure control knob of fireplace is

in the OFF position.

WARNING: Test all gas pip-

3. Check all joints from gas meter to equip-

ment shutoff valve (see Figure 27).Apply

a noncorrosive leak detection fluid to gas

joints. Bubbles forming show a leak.

ing and connections for leaks

after installing or servicing. Cor-

rect all leaks at once.

4. Check all joints from equipment shutoff

valve to thermostat gas valve (see Fig-

ure 27). Apply a noncorrosive leak de-

tection fluid to gas joints. Bubbles

forming show a leak.

4. Correct all leaks at once.

WARNING:Neveruseanopen

flame to check for a leak. Apply a

noncorrosiveleakdetectionfluid

toalljoints.Bubblesformingshow

a leak. Correct all leaks at once.

5. Correct all leaks at once.

_POO_SITpen

Equipment

Shutoff

Valve

6. Light fireplace (see Operating Fire-

place, pages 17 and 18). Check all other

internal joints for leaks.

7. Turn off fireplace (see To Turn Off Gas

to Appliance, page 18).

Pressure Testing Gas Supply

Piping System

Closed

8. Replace front panel.

Test Pressures In Excess Of 1/2 PSIG

(3.5 kPa)

Figure 26 - Equipment Shutoff Valve

1. Disconnect appliance with its appliance

main gas valve (control valve) and equip-

ment shutoff valve from gas supply pip-

ing system. Pressures in excess of 1/2

psig will damage fireplace regulator.

Equipment

Shutoff

Valve

2. Cap off open end of gas pipe where

equipment shutoff valve was connected.

Gas Meter

3. Pressurize supply piping system by either

using compressed air or opening main gas

valve located on or near gas meter.

4. Check all joints of gas supply piping

system. Apply a noncorrosive leak de-

tection fluid to gas joints. Bubbles

forming show a leak.

5. Correct all leaks at once.

6. Reconnect heater and equipment

shutoff valve to gas supply. Check re-

connected fittings for leaks.

Figure 27 - Checking Gas Joints

107105

Download from Www.Somanuals.com. All Manuals Search And Download.

OWNER’S MANUAL

Note: You may be running this fire-

place for the first time after hooking

up to gas supply. If so, the control

knob may need to be pressed in for

30 seconds or more. This will allow

air to bleed from the gas system.

• If control knob does not pop up

when released, contact a qualified

service person or gas supplier for

repairs.

LIGHTING

INSTRUCTIONS

OPERATING

FIREPLACE

WARNING: You must operate

this fireplace with the fireplace

screen in place. Make sure fire-

place screen is installed before

running fireplace.

FOR YOUR SAFETY

READ BEFORE

LIGHTING

WARNING: If you do not fol-

low these instructions exactly, a

fireorexplosionmayresultcaus-

ing property damage, personal

injury or loss of life.

NOTICE: During initial operation

of new fireplace, burning logs

will give off a paper-burning

smell. Orange flame will also be

present. Open window to vent

smell. Operate fireplace on HI

position to burn off odor. This

will only last a few hours.

6. With control knob pressed in, push

down and release ignitor button.

This will light pilot. The pilot is at-

tached to the front of burner. If

needed, keep pressing ignitor but-

ton until pilot lights.

A. This appliance has a pilot which must

be lighted by hand. When lighting the

pilot, follow these instructions exactly.

Note: If pilot does not stay lit, refer

to Troubleshooting, pages 20 through

22. Also contact a qualified service

person or gas supplier for repairs.

Until repairs are made, light pilot with

match. To light pilot with match, see

Manual Lighting Procedure, page 18.

B. BEFORE LIGHTING smell all

around the appliance area for gas. Be

sure to smell next to the floor because

some gas is heavier than air and will

settle on the floor.

1. STOP! Read the safety information,

column 1.

2. Make sure equipment shutoff valve

is fully open.

3. Turn control knob clockwise

to the OFF position.

WHAT TO DO IF YOU SMELL

GAS

7. Keep control knob pressed in for 30

seconds after lighting pilot. After 30

seconds, release control knob.

• Do not try to light any appliance.

• Do not touch any electric switch; do

not use any phone in your building.

• Immediately call your gas supplier

from a neighbor’s phone. Follow

the gas supplier’s instructions.

• If you cannot reach your gas sup-

plier, call the fire department.

4. Wait five (5) minutes to clear out any

gas.Then smell for gas, including near

the floor. If you smell gas, STOP! Fol-

low “B” in the safety information,

column 1. If you don’t smell gas, go

to the next step.

Note: If pilot goes out, repeat steps

3 through 7. This fireplace has a

safety interlock system. Wait one (1)

minute before lighting pilot again.

8. Turn control knob counterclockwise

to desired heating level. The

main burner should light. Set control

knob to any heat level between HI

and LO.

5. Turn control knob counterclockwise

the PILOT position. Press

in control knob for five (5) seconds

(see Figure 28).

C. Use only your hand to push in or turn

the gas control knob. Never use tools.

If the knob will not push in or turn

by hand, don’t try to repair it, call a

qualified service technician or gas

supplier. Force or attempted repair

may result in a fire or explosion.

Control Knob

Ignitor Button

CAUTION:Donottrytoadjust

heatinglevelsbyusingtheequip-

ment shutoff valve.

D. Do not use this appliance if any part

has been under water. Immediately call

a qualified service technician to inspect

the appliance and to replace any part

of the control system and any gas con-

trol which has been under water.

Thermocouple

Ignitor Electrode

Pilot Burner

Figure 28 - Control Knob In The OFF

Position

Figure 29 - Pilot

Continued

107105

Download from Www.Somanuals.com. All Manuals Search And Download.

NATURAL GAS VENT-FREE FIREPLACE SYSTEM

MANUAL LIGHTING

PROCEDURE

1. Follow steps 1 through 5 under Light-

OPERATING

INSPECTING

BURNER

FIREPLACE

Continued

ing Instructions, page 17.

Check pilot flame pattern and burner flame

pattern often.

2. With control knob pressed in, strike

match. Hold match to pilot until pi-

lot lights.

TO TURN OFF GAS

TO APPLIANCE

Shutting Off Fireplace

1. Turn control knob clockwise

to the OFF position.

PILOT FLAME PATTERN

Figure31showsacorrectpilotflamepattern.

Figure 32 shows an incorrect pilot flame

pattern. Theincorrectpilotflameisnotprop-

erlyheatingthethermocouple.Thiswillcause

the thermocouple to cool. When the thermo-

couple cools, the fireplace will shut down.

3. Keep control knob pressed in for 30

seconds after lighting pilot. After 30

seconds, release control knob. Now

follow step 8, page 17.

2. Turn off all electric power to the ap-

pliance if service is to be performed.

Shutting Off Burner Only (pilot

stays lit)

OPERATING BLOWER

If pilot flame pattern is incorrect, as shown

in Figure 32

This blower has three settings: ON, OFF,

andAUTO.IntheONposition,theblower

will operate constantly. In the OFF posi-

tion, the blower will not operate. In the

AUTOposition,theblowerwillstartwhen

thethermostatsensesasufficientincrease

in firebox temperature.

Turn control knob clockwise

the PILOT position.

• turn fireplace off (see To Turn Off Gas to

Appliance)

THERMOSTAT

CONTROL OPERATION

• see Troubleshooting, pages 20 through 22

Note: The pilot flame on natural gas units

will have a slight curve, but flame should be

blue and have no yellow or orange color.

The thermostatic control used on this fire-

place differs from standard thermostats.

Standard thermostats simply turn on and

off the burner. The thermostat used on

this fireplace senses the room tempera-

ture. The thermostat adjusts the amount

of gas flow to the burner. This increases or

decreasestheburnerflameheight.Attimes

the room may exceed the set temperature.

If so, the burner will shut off. The burner

willcyclebackonwhenroomtemperature

drops below the set temperature.

Note: Your fireplace and thermostat

blower will not turn on and off at the

same time. The fireplace may run for

several minutes before the blower turns

on.Aftertheheatermodulatestothepilot

position, the blower will continue to run.

The blower will shut off after the firebox

temperature decreases.

Thermocouple

Pilot Burner

Note: It is safe to operate fireplace with

blower turned off. However, the blower

helps distribute heated air from the

fireplace.

The control knob can be set to any heat

level between HI and LO.

Figure 31 - Correct Pilot Flame Pattern

Auto/Off/On Switch

Note: The thermostat sensing bulb mea-

sures the temperature of air near the

fireplace cabinet. This may not always

agree with room temperature (depend-

ing on housing construction, installation

location, room size, open air tempera-

tures, etc.). Frequent use of your fire-

place will let you determine your own

comfort levels.

Thermocouple

Pilot Burner

OFF

Figure 32 - Incorrect Pilot Flame Pattern

Figure 30 - Auto/Off/On Switch

107105

Download from Www.Somanuals.com. All Manuals Search And Download.

OWNER’S MANUAL

4. Check the injector holder located at the

INSPECTING

CLEANING AND

end of the burner tube again. Remove

any large particles of dust, dirt, lint, or

pet hair with a soft cloth or vacuum

cleaner nozzle.

BURNER

MAINTENANCE

Continued

WARNING: Turn off fireplace

and let cool before cleaning.

BURNER FLAME PATTERN

5. Blow air into the primary air holes on

the injector holder.

Figure 33 shows a correct burner flame

pattern.Figure34showsanincorrectburner

flame pattern. The incorrect burner flame

pattern shows sporadic, irregular flame tip-

ping. The flame should not be dark or have

an orange/reddish tinge.

6. In case any large clumps of dust have

now been pushed into the burner repeat

steps 3 and 4.

CAUTION:Youmustkeepcon-

trol areas, burner, and circulating

air passageways of fireplace

clean. Inspect these areas of fire-

place before each use. Have fire-

place inspected yearly by a quali-

fiedserviceperson.Fireplacemay

need more frequent cleaning due

to excessive lint from carpeting,

pet hair, bedding material, etc.

Clean the pilot assembly also. A yellow tip

on the pilot flame indicates dust and dirt in

the pilot assembly. There is a small pilot air

inlet hole about two inches from where the

pilot flame comes out of the pilot assembly

(see Figure 36). With the unit off, lightly

blow air through the air inlet hole. You may

blowthroughadrinkingstrawifcompressed

air is not available.

Note: When using the fireplace the first

time, the flame will be orange for approxi-

mately one hour until the log cures.

Ifburnerflamepatternisincorrect,asshown

in Figure 34

• turn fireplace off (see To Turn Off Gas to

Appliance, page 18)

CLEANING BURNER

INJECTOR HOLDER AND

PILOT AIR INLET HOLE

Injector Holder

• see Troubleshooting, pages 20 through 22

The primary air inlet holes allow the proper

amount of air to mix with the gas. This pro-

videsacleanburningflame. Keeptheseholes

clear of dust, dirt, lint, and pet hair. Clean

these air inlet holes prior to each heating

season.Blockedairholeswillcreatesoot.We

recommendthatyoucleantheuniteverythree

months during operation and have heater in-

spected yearly by a qualified service person.

Ports/Slots

Burner

Tube

Figure 33 - Correct Burner Flame Pattern

Primary Air Inlet

Holes

Figure 35 - Injector Holder On Outlet

Burner Tube

Wealsorecommendthatyoukeeptheburner

tube and pilot assembly clean and free of

dustanddirt.Tocleanthesepartswerecom-

mend using compressed air no greater than

30 PSI. Your local computer store, hard-

ware store, or home center may carry com-

pressed air in a can. You can use a vacuum

cleaner in the blow position. If using com-

pressed air in a can, please follow the direc-

tions on the can. If you don't follow direc-

tionsonthe can, youcoulddamage the pilot

assembly.

Pilot Air

Inlet Hole

Figure34-IncorrectBurnerFlamePattern

Figure 36 - Pilot Inlet Air Hole

1. Shut off the unit, including the pilot.

Allow the unit to cool for at least thirty

minutes.

CABINET

Air Passageways

2. Inspect burner, pilot, and primary air

inlet holes on injector holder for dust

and dirt (see Figure 35).

• Use a vacuum cleaner or pressurized air

to clean.

Exterior

3. Blow air through the ports/slots and

holes in the burner.

• Use a soft cloth dampened with a mild

soap and water mixture. Wipe the cabi-

net to remove dust.

107105

Download from Www.Somanuals.com. All Manuals Search And Download.

NATURAL GAS VENT-FREE FIREPLACE SYSTEM

TROUBLESHOOTING

Note: For additional help, visit DESA

International’stechnicalservicewebsite

at www.desatech.com.

WARNING: Turn off and un-

plug fireplace and let cool before

servicing. Only a qualified ser-

vice person should service and

repair fireplace.

CAUTION: Never use a wire,

needle, or similar object to clean

ODS/pilot.ThiscandamageODS/

pilot unit.

Note:Alltroubleshootingitemsarelistedin

order of operation.

OBSERVED PROBLEM

POSSIBLE CAUSE

REMEDY

When ignitor button is pressed, there is no 1. Ignitor cable pinched or wet

spark at ODS/pilot

1. Free ignitor cable if pinched by any

metal or tubing. Keep ignitor cable dry

2. Ignitor electrode not connected to igni- 2. Reconnect ignitor cable

tor cable

3. Broken ignitor cable

4. Bad piezo ignitor

5. Ignitor electrode broken

6. Ignitor electrode positioned wrong

3. Replace ignitor cable

4. Replace piezo ignitor

5. Replace pilot assembly

6. Replace pilot assembly

When ignitor button is pressed, there is 1. Gas supply turned off or equipment 1. Turn on gas supply or open equipment

spark at ODS/pilot but no ignition

shutoff valve closed

shutoff valve

2. Control knob not in PILOT position

2. Turn control knob to PILOT position

3. Control knob not pressed in while in 3. Press in control knob while in PILOT

PILOT position

position

4. Air in gas lines when installed

4. Continue holding down control knob. Re-

peat igniting operation until air is removed

5. Clean ODS/pilot (see Cleaning and

Maintenance, page 19) or replace ODS/

pilot assembly

5. ODS/pilot is clogged

6. Gas regulator setting is not correct

6. Replace gas regulator

ODS/pilot lights but flame goes out when 1. Control knob not fully pressed in

1. Press in control knob fully

control knob is released

2. Control knob not pressed in long enough 2. After ODS/pilot lights, keep control

knob pressed in 30 seconds

3. Safety interlock system has been triggered 3. Wait one minute for safety interlock sys-

tem to reset. Repeat ignition operation

4. Equipment shutoff valve not fully open 4. Fully open equipment shutoff valve

5. Thermocouple connection loose at con- 5. Hand tighten until snug, then tighten 1/4

trol valve

turn more

6. Pilot flame not touching thermocouple, 6. A) Contact local natural gas company

which allows thermocouple to cool,

causing pilot flame to go out. This prob-

lem could be caused by one or both of

the following:

B) Clean ODS/pilot (see Cleaning and

Maintenance, page 19) or replace ODS/

pilot assembly

A) Low gas pressure

B) Dirty or partially clogged ODS/pilot

7. Thermocouple damaged

8. Control valve damaged

7. Replace pilot assembly

8. Replace control valve

www.desatech.com

107105

Download from Www.Somanuals.com. All Manuals Search And Download.

OWNER’S MANUAL

TROUBLESHOOTING

Continued

OBSERVED PROBLEM

POSSIBLE CAUSE

REMEDY

Burner does not light after ODS/pilot is lit

1. Burner orifice is clogged

1. Clean burner (see Cleaning and Mainte-

nance, page 19) or replace burner orifice

2. Contact local natural gas company

2. Inlet gas pressure is too low

Delayed ignition of burner

1. Manifold pressure is too low

2. Burner orifice is clogged

1. Contact local natural gas company

2. Clean burner (see Cleaning and Mainte-

nance, page 19) or replace burner orifice

Burner backfiring during combustion

1. Burner orifice is clogged or damaged

1. Clean burner (see Cleaning and Mainte-

nance, page 19) or replace burner orifice

2. Replace burner pressure

2. Burner damaged

3. Low inlet gas pressure

3. Contact local natural gas company

4. Gas regulator defective

4. Replace gas regulator

Yellow flame during burner combustion

1. Not enough air

1. Check burner for dirt and debris. If

found, clean burner (see Cleaning and

Maintenance, page 19)

2. Gas regulator defective

2. Replace gas regulator

Slight smoke or odor during initial operation 1. Residues from manufacturing processes 1. Problem will stop after a few hours of

operation

Fireplace produces a whistling noise when 1. Turning control knob to HI position 1. Turn control knob to LO position and

burner is lit

when burner is cold

let warm up for a minute

2. Air in gas line

2. Operate burner until air is removed from

line. Have gas line checked by local

natural gas company

3. Air passageways on fireplace blocked

3. Observe minimum installation clear-

ances (see pages 8 through 10)

4. Dirty or partially clogged burner orifice 4. Clean burner (see Cleaning and Mainte-

nance, page 19) or replace burner orifice

Whitepowderresidueformingwithinburner 1. When heated, vapors from furniture pol- 1. Turn heater off when using furniture

box or on adjacent walls or furniture

ish, wax, carpet cleaners, etc. may turn

into white powder residue

polish, wax, carpet cleaners, or similar

products

www.desatech.com

Continued

107105

Download from Www.Somanuals.com. All Manuals Search And Download.

NATURAL GAS VENT-FREE FIREPLACE SYSTEM

TROUBLESHOOTING

Continued

WARNING: If you smell gas

• Shut off gas supply.

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your

building.

• Immediatelycallyourgassupplierfromaneighbor’sphone. Followthe

gas supplier’s instructions.

• If you cannot reach your gas supplier, call the fire department.

IMPORTANT:Operatingfireplacewhereimpuritiesinairexistmaycreateodors.Cleaning

supplies, paint, paint remover, cigarette smoke, cements and glues, new carpet or textiles,

etc., create fumes. These fumes may mix with combustion air and create odors.

OBSERVED PROBLEM

POSSIBLE CAUSE

REMEDY

Fireplace produces a clicking/ticking noise 1. Metal expanding while heating or con- 1. This is common with most fireplaces. If

just after burner is lit or shut off

tracting while cooling

noise is excessive, contact qualified ser-

vice person

Fireplace produces unwanted odors

1. Fireplace burning vapors from paint, hair 1. Ventilate room. Stop using odor caus-

spray, glues, etc. (See IMPORTANT

ing products while fireplace is running

statement above)

2. Gas leak. SeeWarning statement at 2. Locate and correct all leaks (see Check-

top of page

ing Gas Connections, page 16)

Fireplace shuts off in use (ODS operates)

1. Not enough fresh air is available

2. Low line pressure

3. ODS/pilot is partially clogged

1. Open window and/or door for ventilation

2. Contact local natural gas company

3. Clean ODS/pilot (see Cleaning and

Maintenance, page 19)

Gas odor even when control knob is in OFF 1. Gas leak. SeeWarning statement at 1. Locate and correct all leaks (see Check-

position

top of page

ing Gas Connections, page 16)

2. Control valve defective

2. Replace control valve

Gas odor during combustion

1. Foreign matter between control valve 1. Take apart gas tubing and remove for-

and burner eign matter

2. Gas leak. SeeWarning statement at 2. Locate and correct all leaks (see Check-

top of page

ing Gas Connections, page 16)

Moisture/condensationnoticedonwindows 1. Not enough combustion/ventilation air

1. Refer to Air for Combustion and Venti-

lation requirements (page 5)

www.desatech.com

107105

Download from Www.Somanuals.com. All Manuals Search And Download.

OWNER’S MANUAL

SPECIFICATIONS

REPLACEMENT

PARTS

Btu (Variable)

Type Gas

14,000/26,000

Natural Only

Piezo

Note: Use only original replacement parts.

Thiswillprotectyourwarrantycoveragefor

parts replaced under warranty.

Ignition

Pressure Regulator Setting

3" W.C.

Inlet Gas Pressure (in. of water) *

Maximum

PARTS UNDER WARRANTY

10.5"

Contact authorized dealers of this product.

If they can’t supply original replacement

part(s) call DESA International’s Technical

Service Department at 1-866-672-6040 for

referral information.

Minimum

Dimensions, Inches (H x W x D)

Fireplace (including hood and screws)

Carton

25 ⁷/8 x 26 ¹³/16 x 9 ³/8

32 ⁵/8 x 27 ³/16 x 11 ⁵/8

Weight, pounds

Fireplace

When calling DESA International, have

ready

44 ¹/2 lbs.

48 lbs.

Shipping

• your name

* For purposes of input adjustment

• your address

• model and serial numbers of your fireplace

• how fireplace was malfunctioning

TECHNICAL

SERVICE

SERVICE HINTS

• type of gas used (propane/LP or natural

gas)

When Gas Pressure Is Too Low

• purchase date

You may have further questions about in-

stallation, operation, or troubleshooting. If

so, contact DESA International’s Technical

Service Department at 1-866-672-6040.

• pilot will not stay lit

• burner will have delayed ignition

• fireplace will not produce specified heat

Usually, we will ask you to return the part to

the factory.

You may feel your gas pressure is too low. When calling, please have your model and

Ifso, contactyourlocalnaturalgassupplier. serial numbers of your heater ready.

PARTS NOT UNDER

WARRANTY

You can also visit DESA International’s

technical services web site at

www.desatech.com.

Contact authorized dealers of this product. If

theycan’tsupplyoriginalreplacementpart(s)

call DESA International at 1-866-672-6040

for referral information.

When calling DESA International, have

ready

• model number of your fireplace

• the replacement part number

107105

Download from Www.Somanuals.com. All Manuals Search And Download.

NATURAL GAS VENT-FREE FIREPLACE SYSTEM

ILLUSTRATED

PARTS

BREAKDOWN

FMH26TN

107105

Download from Www.Somanuals.com. All Manuals Search And Download.

OWNER’S MANUAL

This list contains replaceable parts used in your fireplace. When ordering parts, follow the instructions

listed under Replacement Parts on page 23 of this manual.

PARTS LIST

FMH26TN

KEY NO.

PART NO.

DESCRIPTION

QTY.

102633-02

102624-02

099230-02

098304-01

107178-01

103209-05

102635-02CK

101629-02

103209-01

104281-02BR

102638-01

104285-01

099211-01

103963-01

102834-01

098304-03

098303-02

104335-01CK

102649-01CK

099415-10

102875-01

101381-01

099387-11

098271-06

107186-02

101006-02

098249-01

098522-23

102639-01

101628-01

102869-01

102731-01

103295-03BR

107153-01

104313-01

104313-02

M10908-2

103734-01

M11084-26

097809-03

101629-01

Outer Casing Top

Outer Casing

Shoulder Screw

Screw, #10 x 3/8"

Burner

Louvered Door

Left and Right Side Front

Bushing

Top Louver

Firebox Hood

Firebox Top

ODS/Pilot Assembly

Firebox Wrapper

Control Bracket Screw

Inlet Tube

Burner Tube

Screw 8-18 x 3/8"

Regulator Screw

Outer Shell Base

Branch Support

Gas Regulator

Regulator Bracket

Valve Cover and Piezo

Pilot Tube

Ignitor Cable

Injector

Pilot Bracket

Nut, M5

Gas Valve

Baffle

Flexible Connector

Control Bracket

Control Shield

Screen Assembly

Log Set Assembly Kit

Right Hinge

Left Hinge

Hinge Screws

Burner Support

Hex Head Screw, #10 x 3/8"

3/8" NPT x 3/8" Flare Brass Fitting

Bushing

PARTS AVAILABLE — NOT SHOWN

101054-01

100563-01

103470-01

Lighting Instructions Plate

Warning Plate

Hardware Package

** Part not available for field replacement.

107105

Download from Www.Somanuals.com. All Manuals Search And Download.

NATURAL GAS VENT-FREE FIREPLACE SYSTEM

ACCESSORIES

Purchase these fireplace accessories from

your local dealer. If they cannot supply these

accessories call DESA International’s Sales

Department at 1-866-672-6040 for referral

information. You can also write to the ad-

dress listed on the back page of this manual.

THERMOSTATICALLY -

CONTROLLED BLOWER KIT

GA3400T

For all models. Provides better heat distri-

bution. Makes fireplace more efficient.

Automatically turns off and on as needed.

CORNER MANTEL WITH

FULL HEARTH BASE

Unfinished - GMC63U

Finished - GMC64F

White Lacquer - GMC65W

CLEANING KIT - GCK

(Not Shown)

EQUIPMENT SHUTOFF

VALVE - GA5010

Forusewithfireplace. Space-savingmantel

andhearthbasecornerdesignfeaturesclean,

classic lines. Available in a stained oak

finish,whitelacquerfinish,oranunfinished

birch, ready to stain or paint. Complete

assemblyinstructionsincluded.Three-sided

brass trim kit included.

For all models. Your vent-free gas appli-

ance requires regular cleaning and mainte-

nance to prevent performance problems.

This kit gives you the tools and instructions

to make it easy to clean all critical areas of

your appliance.

For all models. Equipment shutoff valve

with 1/8" NPT tap.

BRASS TRIM KIT - GA6094

Optional three-sided brass trim kit for cus-

tom and recessed installations (when unit is

on the floor). Provides a finished appear-

CABINET MANTEL WITH

FULL HEARTH BASE AND

ance by covering rough edges of wall open- ROUNDED LEG STYLING

ing. Included with all mantels.

Unfinished - GMC61U

Oak Finished - GMC60F

(Appearance May Differ by Model)

BRASS TRIM KIT - GA6095

Optional four-sided brass trim kit for recessed

built-ininstallations(whenunitisraisedoffof

the floor. Provides a finished appearance by

covering rough edges of wall opening.

For use with fireplace. A mantel and hearth

base offers compact styling and completes

the fireplace look. Available in a oak stain

finish, or an unfinished birch, ready to stain

or paint. Complete assembly instructions

included.Three-sidedbrasstrimkitincluded.

107105

Download from Www.Somanuals.com. All Manuals Search And Download.

OWNER’S MANUAL

NOTES

_______________________________________________________________________________________________

107105

Download from Www.Somanuals.com. All Manuals Search And Download.

WARRANTY INFORMATION

KEEP THIS WARRANTY

Model

Serial No.

Date Purchased

Always specify model and serial numbers when communicating with the factory.

We reserve the right to amend these specifications at any time without notice. The only warranty applicable is our standard written

warranty. We make no other warranty, expressed or implied.

LIMITED WARRANTY

VENT-FREE NATURAL GAS COMPACT HEAT MAJIC™ FIREPLACE SYSTEM

DESA International warrants this product to be free from defects in materials and components for four (4) years and five (5) years

on stainless steel burners from the date of first purchase, provided that the product has been properly installed, operated and

maintained in accordance with all applicable instructions. To make a claim under this warranty the Bill of Sale or cancelled check

must be presented.

This warranty is extended only to the original retail purchaser. This warranty covers the cost of part(s) required to restore this

fireplace to proper operating condition and an allowance for labor when provided by a DESA Authorized Service Center. Warranty

part(s) MUST be obtained through authorized dealers of this product and/or DESA International who will provide original factory

replacement parts. Failure to use original factory replacement parts voids this warranty. The fireplace MUST be installed by a

qualified installer in accordance with all local codes and instructions furnished with the unit.

This warranty does not apply to parts that are not in original condition because of normal wear and tear, or parts that fail or become

damagedasaresultofmisuse, accidents, lackofpropermaintenanceordefectscausedbyimproperinstallation. Travel, diagnosticcost,

labor, transportation and any and all such other costs related to repairing a defective fireplace will be the responsibility of the owner.

TOTHEFULLEXTENTALLOWEDBYTHELAWOFTHEJURISDICTIONTHATGOVERNSTHESALEOFTHEPRODUCT;

THIS EXPRESS WARRANTY EXCLUDES ANY AND ALL OTHER EXPRESSED WARRANTIES AND LIMITS THE DURA-

TION OF ANY AND ALL IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS

FORAPARTICULARPURPOSETOFOUR(4)YEARSONALLCOMPONENTSANDFIVE(5)YEARSONSTAINLESSSTEEL

BURNERS FROM THE DATE OF FIRST PURCHASE; AND DESA INTERNATIONAL’S LIABILITY IS HEREBY LIMITED TO

THE PURCHASE PRICE OF THE PRODUCT AND DESA INTERNATIONAL SHALL NOT BE LIABLE FOR ANY OTHER

DAMAGES WHATSOEVER INCLUDING INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES.

Some states do not allow a limitation on how long an implied warranty lasts or an exclusion or limitation of incidental or

consequential damages, so the above limitation on implied warranties, or exclusion or limitation on damages may not apply to you.

This warranty gives you specific legal rights, and you may also have other rights that vary from state to state.

For information about this warranty write:

2701 Industrial Drive

P.O. Box 90004

Bowling Green, KY 42102-9004

www.desatech.com

107105-01

107105 01

Rev. C

04/02

NOT A UPC

Download from Www.Somanuals.com. All Manuals Search And Download.

Eiki Fitness Equipment LC X50 User Manual
Evolution Technologies Oxygen Equipment OM 900M User Manual
Extron electronic Switch 2 VGAcc User Manual
Extron electronic Switch 12800 User Manual
Extron electronic Switch FOX T USW 203 User Manual
Fisher Price Baby Toy T6340 User Manual
Fisher Price Motorized Toy Car 74598 User Manual
Frigidaire Washer LTF2140FS1 User Manual
FujiFilm Digital Camera Z100fd User Manual
GE Range 10 95 CG User Manual