Extron electronic Pacemaker MTP 15HD RS User Manual

MTP 15HD RS Series • Setup Guide  
This card provides quick start instructions for an experienced installer to set up and operate any of the MTP VGA video and RS‑232 transmission  
systems.  
Unjumpered for  
One-way (Default)  
Pre-installation — RS-232 Jumper  
The receiver’s RS‑232 circuits are factory‑set to be one‑way, transmitter to receiver. If the system has only one  
receiver, jumper JMP 1 on the main board can be set for two‑way communication as shown at right.  
JMP3  
JMP2  
JMP1  
Installation  
Step 1 — Mounting  
Jumpered for  
Two-way  
Turn off or disconnect all equipment power sources and mount the MTP transmitter and up to eight receivers  
as required.  
RS-232  
Tx Rx  
Step 2 — Transmitter Inputs  
Connect a computer (VGA) video source to the Input connector.  
Connect a VGA monitor to the Monitor connector.  
Plug an RS‑232 device into the RS‑232 port. Wire the connector as shown below.  
INPUT  
MONITOR  
Tx  
Rx  
Receive  
Transmit  
Ground  
Connected  
RS-232  
Device Pins  
Pins:  
12345678  
MTP  
Pins  
T568A  
Wire Color  
T568B  
Wire Color  
Gnd  
Pin  
1
White-green  
White-orange  
2
3
4
5
Green  
Orange  
Step 3 — TP Cables Between Units  
White-orange  
Blue  
White-green  
Blue  
Terminate a TP cable as shown at right. Connect it between the transmitter’s Output port and the  
receiver’s Input port (both ends must match).  
White-blue  
White-blue  
6
7
8
Orange  
Green  
White-brown  
Brown  
White-brown  
Brown  
Insert Twisted  
Pair Wires  
NOTE: If the unit is labeled “C7,” only CAT 7 cable should be used.  
NOTE: If you are using Enhanced Skew-Free™  
A/V cable, use the TIA/EIA T568A standard only.  
For daisy-chaining, connect up to eight TP cables between a receiver’s Buffered  
Output port and a daisy‑chained receiver’s Input port.  
RS-232  
Tx Rx  
Step 4 — Receiver Outputs  
Connect a VGA monitor to the Output connector.  
Plug an RS‑232 device into the RS‑232 port. Wire the connector as shown in step 2, above.  
OUTPUT  
Step 5 — Receiver DIP Switches  
H Sync and V. Sync switches — Set these switches up for positive sync or down for negative sync.  
ON  
Composite Sync, (SOG), and Video switches — Set these switches as shown in the following table to output the  
indicated format.  
1
2
3
4
5
6
Output Format  
C Sync  
SOG  
Video  
RGBHV  
RGBS  
RGsB  
Component*  
S‑Video*  
Composite*  
NOTE: * Input video format must match.  
End Unit switch — Set this switch up if either of the following is true:  
The receiver being configured is the only receiver connected to the transmitter.  
The receiver being configured is the last receiver in a daisy‑chained system.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Dyson Vacuum Cleaner DC18SAOP User Manual
Earlex Paint Sprayer HV7000 User Manual
Everpure Water System CGCC 1 User Manual
Excell Precision Pressure Washer VR2300 User Manual
Fisher Paykel Sleep Apnea Machine HC230 User Manual
Fisher Price Bouncy Seat B8865 User Manual
Fluke Thermometer 80t 150u User Manual
Garmin Car Stereo System 695 User Manual
GE Air Conditioner AEE08AK User Manual
Globalsat Technology GPS Receiver BU 303 SiRF II BU 353 SiRF III User Manual