Important
Please read PRECAUTIONS, this User’s Manual and Setup Guide
(separate volume) carefully to familiarize yourself with safe and effective
usage.
• Please read the Setup Guide (separate volume)
• The latest User’s Manual is available for download from our site:
Download from Www.Somanuals.com. All Manuals Search And Download.
Notice for this monitor
This product is suited to creating documents, viewing multimedia content, and other general purposes.
This product has been adjusted specifically for use in the region to which it was originally shipped. If the product is used
outside the region, it may not operate as specified in the specifications.
This product may not be covered by warranty for uses other than those described in this manual.
The specifications noted in this manual are only applicable for power cords and signal cables specified by us.
Use optional products manufactured or specified by us with this product.
As it takes about 30 minutes for the performance of electrical parts to stabilize, adjust the monitor 30 minutes or more
after the monitor power has been turned on.
In order to suppress the luminosity change by long-term use and to maintain the stable luminosity, use of a monitor in
lower brightness is recommended.
When the screen image is changed after displaying the same image for extended periods of time, an afterimage may
appear. Use the screen saver or timer to avoid displaying the same image for extended periods of time.
Periodic cleaning is recommended to keep the monitor looking new and to prolong its operation lifetime.
The LCD panel is manufactured using high-precision technology. However, missing pixels or lit pixels may appear on
the LCD panel, this is not malfunction.
Percentage of effective pixels : 99.9994% or higher.
The backlight of the LCD panel has a fixed life span. When the screen becomes dark or begins to flicker, please contact
your dealer.
Do not press on the panel or edge of the frame strongly, as this may result in the display malfunction, such as the
interference patterns, etc. If pressure is continually applied to the LCD panel, it may deteriorate or damage your LCD
panel. (If the pressure marks remain on the LCD panel, leave the monitor with a white or black screen. The symptom
may disappear.)
Do not scratch or press on the panel with any sharp objects, such as a pencil or pen as this may result in damage to the
panel. Do not attempt to brush with tissues as this may scratch the LCD panel.
When the monitor is cold and brought into a room or the room temperature goes up quickly, dew condensation
may occur inside and outside the monitor. In that case, do not turn the monitor on and wait until dew condensation
disappears, otherwise it may cause some damages to the monitor.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning
Attention
• Never use any solvents or chemicals, such as thinner, benzene, wax, alcohol, and abrasive cleaner, which may damage
the cabinet or LCD panel.
NOTE
• Optional ScreenCleaner is recommended for cleaning the panel surface.
[LCD Panel]
• Clean the LCD panel with a soft cloth such as cotton cloth or lens cleaning paper.
• Remove persistent stains gently with a cloth dampened with a little water, and then clean the LCD panel again with a
dry cloth for better finishing.
[Cabinet]
Clean the cabinet with a soft cloth dampened with a little mild detergent.
To use the monitor comfortably
• An excessively dark or bright screen may affect your eyes. Adjust the brightness of the monitor according to the
environmental conditions.
• Staring at the monitor for a long time tires your eyes. Take a 10-minute rest every hour.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
Notice for this monitor.............................................. 3
2-11 Screen Size Selection.................................... 23
● To change screen size [Screen Size] ............... 23
● To adjust brightness of non-display area
CONTENTS............................................................. 5
[Border Intensity] .............................................. 23
Chapter 1 Features and Overview ..................... 7
2-12 Setting Adjustment Menu Display................ 24
● To update menu settings [Menu Size/Menu
1-1 Features............................................................ 7
1-2 Controls and Functions .................................. 8
1-3 Compatible Resolutions/Frequencies ........... 9
1-4 Functions and Basic Operation.................... 10
Position/Menu Off Timer/Translucent] .............. 24
2-13 Setting Orientation ........................................ 25
● To set the orientation of the Adjustment menu
[Orientation]...................................................... 25
2-14 Locking Buttons ............................................ 25
Chapter 2 Settings and Adjustments .............. 13
2-15 Displaying Monitor Information
[Information]................................................... 25
2-1 Utility Disk ...................................................... 13
● Disk contents and software overview............... 13
● To use ScreenManager Pro for LCD ................ 13
2-16 Enabling/Disabling DDC/CI communication.... 26
2-17 Setting Power Indicator ON/OFF
2-2 Screen Adjustment ........................................ 14
Digital Input.......................................................... 14
Analog Input ........................................................ 14
[Power Indicator] ........................................... 26
2-18 Setting Language [Language] ...................... 26
2-19 Setting EIZO logo display ON/OFF............... 26
2-3 Color Adjustment........................................... 17
● To select the display mode (FineContrast mode)...17
● To perform advanced adjustments ................... 18
● Adjustment items in each mode ....................... 18
● To adjust the brightness [Brightness] ............... 18
● To adjust the contrast [Contrast]....................... 18
● To adjust the color temperature [Temperature].... 19
● To adjust the gamma value [Gamma]............... 19
● To adjust the color saturation [Saturation]........ 19
● To adjust the hue [Hue] .................................... 20
● To adjust the gain value [Gain]......................... 20
2-20 Resuming the Default Setting [Reset] ......... 27
● To reset color adjustment values...................... 27
● To reset all adjustments to the factory default
settings............................................................. 27
Chapter 3 Connecting Cables .......................... 28
3-1 Connecting More than Two PCs to the Monitor... 28
● To switch the input signal ................................. 28
● To set input signal selection [Input Signal] ....... 29
3-2 Adjusting the DVI Input Level
2-4 Adjusting Volume [Volume] .......................... 20
[DVI Input Level] ............................................ 29
2-5 Switching sound source during DisplayPort
signal input [Source]....................................... 20
3-3 Connecting Peripheral USB Devices............... 30
2-6 Turning off the audio output at Power Saving
mode [Power Save] ......................................... 21
2-7 Setting On/Off for the automatic brightness
adjustment function [Auto EcoView] ............ 21
2-8 Setting On/Off for Power Saving mode
[Power Save] .................................................. 21
2-9 Turning off the monitor automatically
[Off Timer] ...................................................... 22
2-10 Displaying the level of power saving by
EcoView Index................................................ 22
CONTENTS
5
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
Chapter 4 Troubleshooting............................... 31
Chapter 5 Reference ......................................... 34
5-1 Attaching an Arm........................................... 34
5-2 Folding the EZ-UP stand............................... 35
5-3 Specifications ................................................ 36
5-4 Glossary ......................................................... 44
5-5 Preset Timing................................................. 46
FCC Declaration of Conformity.......................... 47
Hinweise zur Auswahl des richtigen
Schwenkarms für Ihren Monitor......................... 48
Hinweis zur Ergonomie....................................... 48
CONTENTS
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Features and Overview
Thank you very much for choosing an EIZO color LCD monitor.
1-1 Features
• 22” wide format LCD Applicable to WSXGA+ (1680×1050) (S2233W)/
22” wide format LCD Applicable to WUXGA (1920×1200) (S2243W)
• Built-in speakers and headphone jack
• Power saving function
Suppressing the power consumption*1 reduces the carbon dioxide emissions.
This product is equipped with various power saving functions.
–
Power Consumption when main power switch is Off: 0W
Equipped with main power switch.
Turning off the main power switch completely shuts off power supply to the monitor while the monitor is not used.
–
Auto EcoView function
The sensor on the front side of the monitor detects the environmental brightness to adjust the screen brightness automatically
and comfortably.
Excessively high brightness may lead a damage to the natural environment as well as to your eyes. Suppressing the excessively
high brightness will be helpful to reduce the power consumption and the damage to your eyes.
– EcoView Index function
The green indicator shows the power consumption ratio responding to the brightness of the monitor. You can realize the power
consumption reduction by taking consideration in the ratio of power saving.
• FineContrast function
• Applicable to DisplayPort (applicable to 8 bit)*2
The image signal and audio signal can both be transmitted via a single DisplayPort cable (option).
• Applicable to DVI long cable
• Portrait/Landscape display available
• The software “ScreenManager Pro for LCD” to adjust the screen using the mouse and keyboard is included
• HDCP (High-bandwidth Digital Content Interface)
1
*
Reference values:
– S2233W
Maximum power consumption: 80W (Luminance Max., at default settings)
Standard power consumption: 32W (Luminance 120cd/m2, at default settings)
– S2243W
Maximum power consumption: 80W (Luminance Max., at default settings)
Standard power consumption: 36W (Luminance 120cd/m2, at default settings)
When transmitting an audio signal using the DisplayPort cable, the graphics board must be compatible with audio
2
*
output.
NOTE
• This monitor supports the Portrait/Landscape display. This function allows you to change the orientation of the Adjustment menu
when using the monitor screen in vertical display position. (Refer to “To set the orientation of the Adjustment menu [Orientation]”
• For using the monitor with “Portrait” position, the graphics board supporting portrait display is required. When using the monitor
with “Portrait” position, the setting needs to be changed depending on the graphics board used in your PC. Refer to the manual of
the graphics board for details.
• The stand of the unit can be replaced with an arm or another stand. (Refer to “5-1 Attaching an Arm” on page 34.)
Chapter 1 Features and Overview
7
Download from Www.Somanuals.com. All Manuals Search And Download.
1-2 Controls and Functions
Ex. Height adjustable stand
16
17
18
Adjustment menu
®
20
*
21
( ScreenManager
)
1
2
3
4
5
6
7
8 9
19
10 11 12
13 14 15
1
2
3
4
Sensor
Auto EcoView button
EcoView Index button
Input Signal Selection button
Switches input signals for display when more than two PCs are connected to
5
6
Mode button
Enter button
Displays the Adjustment menu, determines an item on the menu screen, and
7
Control buttons (Left, Down,
Up, Right)
• Chooses an adjustment item or increases/decreases adjusted values for
•
•
or
or
8
9
Power button
Turns the power on or off.
Power indicator
Indicates monitor’s operation status.
Blue: Operating
Orange: Power saving
Off: Power off
10 Speaker
Outputs audio source.
11 Main Power Switch
12 Power connector
13 Stereo mini jack
Turns the main power on or off.
Connects the power connector.
Connects the stereo mini jack cable.
Left : DisplayPort Connector / Center : DVI-I Connector / Right : D-Sub mini
15-pin connector
14 Input signal connectors
15 USB port (Up)
Connects the USB cable to use the software that needs USB connection, or
16 USB Port (Down)
17 Stand
Connects a peripheral USB device.
Used to adjust the height and angle of the monitor screen.
Covers the monitor cables.
18 Cable holder
19 Headphone jack
20 Security lock slot
Connects the headphones.
Complies with Kensington’s MicroSaver security system.
21 Option speaker (i·Sound L3)
mounting holes
Used to attach the option speaker (i·Sound L3). (May not allowed to attach
the option speaker depending on the stand type.)
Chapter 1 Features and Overview
8
Download from Www.Somanuals.com. All Manuals Search And Download.
1-3 Compatible Resolutions/Frequencies
The monitor supports the following resolutions.
Analog Input (D-Sub)
S2233W
S2243W
Resolution
Frequency
Mode
Dot Clock ~150MHz Dot Clock ~202.5MHz
√
√
√
√
√
√
√
–
√
–
√
√
√
√
√
√
√
√
√
√
640 × 480
720 × 400
~75 Hz
70 Hz
VGA, VESA
VGA TEXT
800 × 600
~75 Hz
~75 Hz
75 Hz
VESA
1024 × 768
1152 × 864
1280 × 960
1280 × 1024
1600 × 1200
2 1680 × 1050
3 1920 × 1200
VESA
VESA
VESA
60 Hz
~75 Hz
~75 Hz
60 Hz
VESA
VESA
1
* *
VESA CVT
VESA CVT, VESA CVT RB
1
* *
60 Hz
Digital Input (DVI-D)
Resolution
S2233W
S2243W
Frequency
Mode
Dot Clock ~120MHz
Dot Clock ~162MHz
√
√
√
√
√
√
–
–
√
–
√
√
√
√
√
√
√
√
√
√
640 × 480
720 × 400
60 Hz
70 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
VGA
VGA TEXT
VESA
800 × 600
1024 × 768
1280 × 960
1280 × 1024
1600 × 1200
1 1680 × 1050
2 1680 × 1050
3 1920 × 1200
VESA
VESA
VESA
VESA
*
VESA CVT
VESA CVT RB
VESA CVT RB
1
* *
1
* *
Digital Input (DisplayPort)
Resolution
S2233W
S2243W
Frequency
Mode
Dot Clock ~120MHz
Dot Clock ~162MHz
√
√
√
√
√
√
√
√
√
–
–
√
–
√
√
√
√
√
√
√
√
√
√
√
√
√
640 × 480
720 × 400
60 Hz
70 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
VGA, CEA
VGA TEXT
CEA
720 × 400 (4:3)
720 × 400 (16:9)
800 × 600
CEA
VESA
1024 × 768
1280 × 720
1280 × 960
1280 × 1024
1600 × 1200
1 1680 × 1050
2 1680 × 1050
3 1920 × 1200
VESA
CEA
VESA
VESA
VESA
*
VESA CVT
VESA CVT RB
VESA CVT RB
1
* *
1
* *
1
2
3
*
*
*
When displaying the wide format input signal, a graphics board in conformance with VESA CVT standard is required.
Recommended resolution (S2233W: Set this resolution)
Recommended resolution (S2243W: Set this resolution)
Chapter 1 Features and Overview
9
Download from Www.Somanuals.com. All Manuals Search And Download.
1-4 Functions and Basic Operation
To adjust the screen and color
[At analog signal input]
Analog input only
1
Screen Adjustment
(Automatic Adjustment)
●
●
To adjust flickering and position
[Screen]……………………………… see page 14
To adjust color gradation automatically
[At digital signal input]
[Range] ……………………………… see page 16
2
Screen Adjustment
(Advanced Adjustment)
[At analog signal input] [At digital signal input]
• The Adjustment menu and the FineContrast mode
name cannot be displayed at the same time.
FineContrast mode
Color Adjustment
●
●
To remove flickering or blurring
Simple Adjustment [FineContrast mode]
This function allows easy selection of a desired mode
from six modes according to monitor application.
[Phase*]……………………………… see page 15
To correct screen position
[Position*] …………………………… see page 16
To modify blurred characters/lines
To set when a noise appears on the screen
●
●
●
*
Items marked with * can be adjusted with analog
input.
●
●
To adjust the brightness [Brightness]
Press or to adjust brightness.
Color Adjustment
Advanced Adjustment
Adjusting Volume [Volume]
Press or to adjust volume.
●
“Brightness”, “Contrast”, “Temperature”,
●
●
Setting On/Off for the automatic brightness
adjustment function [Auto EcoView]
“Gamma”, “Saturation”, “Hue” and “Gain” can be
set for each mode (Custom/EyeCare/sRGB/Text/
Picture/Movie).
Settable functions vary with the FineContrast
mode.
Press
to switch the setting.
Displaying the level of power saving by EcoView
Index
Press
to display the level of power saving mode.
Resuming the default settings
●
To reset color adjustment values
Chapter 1 Features and Overview
10
Download from Www.Somanuals.com. All Manuals Search And Download.
To make useful settings/adjustments
[At analog signal input]
Power-save Settings
●
●
●
Setting On/Off for Power Saving mode
Turning off the monitor automatically
Displaying the level of power saving by EcoView
[At digital signal input]
Other Settings
● To change screen size [Screen Size]
……………………………………… see page 23
● To adjust brightness of non-display area
[Border Intensity] …………………… see page 23
Information
●
To set input signal selection
To update menu settings
●
[Menu Size/Menu Position/Menu Off Timer/
Translucent] ………………………… see page 24
To set the orientation of the Adjustment menu
Setting Power Indicator ON/OFF
[Power Indicator] …………………… see page 26
To reset all adjustments to the factory default
●
●
●
●
Displaying Monitor Information [Information]
Language
Sound Settings
[At D-Sub/DVI-D signal input]
[At DisplayPort signal input]
●
Setting Language [Language]
●
●
Enabling/Disabling DDC/CI communication
Adjusting the DVI Input Level
●
●
Adjusting Volume [Volume]………… see page 20
Switching sound source during DisplayPort
signal input [Source*] ……………… see page 20
Turning off the audio output at Power Saving
mode [Power Save]………………… see page 21
●
●
●
[DVI Input Level] ……………………… see page 29
*
An item marked with * can be adjusted with
DisplayPort input.
Chapter 1 Features and Overview
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic operation of Adjustment menu
[Displaying Adjustment menu and selecting function]
(1) Press
. The Main menu appears.
(2) Select a function with
(3) Select a function with
/
/
/
/
/
/
, and press
, and press
. The Sub menu appears.
. The adjustment/setting menu appears.
, and press . The setting is saved.
(4) Adjust the selected item with
/
/
/
[Exiting Adjustment menu]
(1) Choose <Return> from the Sub menu and press
(2) Choose <Exit> from the Main menu and press
. The Main menu appears.
. The Adjustment menu quits.
NOTE
• The Adjustment menu can also be exited by pressing
twice quickly.
• <Exit> or <Return> can also be selected by pressing
twice in the Main menu or Sub menu.
Chapter 1 Features and Overview
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Settings and Adjustments
2-1 Utility Disk
An “EIZO LCD Utility Disk” (CD-ROM) is supplied with the monitor. The following table shows the disk contents and
the overview of the software programs.
●
Disk contents and software overview
The disk includes application software programs for adjustment, and User’s Manual. Refer to “Readme. txt” file on the
disk for software startup procedures or file access procedures.
Item
A “Readme.txt” file
Overview
OS
Screen adjustment pattern files
ScreenManager Pro for LCD
Used when adjusting the image of the
analog signal input manually.
A software for adjusting the screen using Windows XP/Vista
the mouse and keyboard.
Connect the monitor to the PC with the
supplied USB cable before installation.
* WindowMovie Checker Software WindowMovie is a function of
ScreenManager Pro for LCD. For more
information, refer to the User’s Manual
of ScreenManager Pro for LCD on the
disk.
EIZO ScreenSlicer
A software that divides a screen and
lays out multiple windows efficiently.
Windows XP/Vista
User’s Manual of this monitor (PDF file)
●
To use ScreenManager Pro for LCD
For the installation and use of ScreenManager Pro for LCD, refer to its User’s Manual on the disk.
To adjust the monitor using ScreenManager Pro for LCD, connect a PC to the monitor with the supplied USB cable.
Chapter 2 Settings and Adjustments
13
Download from Www.Somanuals.com. All Manuals Search And Download.
2-2 Screen Adjustment
Digital Input
When digital signals are input, images are displayed correctly based on the
preset data of the monitor, but if characters and/or lines appear blurred, go to
step 6 “To modify blurred characters/lines [Smoothing]”. When performing
subsequent pages.
Attention
• Wait 30 minutes or more from
monitor power on before starting
adjustments.
Analog Input
• Auto adjust function does not work
for the images under the resolution of
800 × 600 (SVGA).
The monitor screen adjustment is used to suppress flickering of the screen or
adjust screen position and screen size correctly according to the PC to be used.
The auto adjust function works in the following cases:
• When a signal is input into the monitor for the first time
• When the resolution or Vertical/Horizontal Frequency not
displayed before is set
If the screen is not displayed correctly even after performing the auto
adjustment, perform the screen adjustments according to the procedures on the
following pages to use the monitor comfortably.
[Adjustment Procedure]
Attention
Perform the auto adjustment.
1
• This function works correctly when
an image is fully displayed over the
Windows or Macintosh display area.
It does not work properly when an
image is displayed only on a part of
the screen (command prompt window,
for example) or when a black
● To adjust flickering, screen position, and screen size
automatically [Screen]
(1) Choose <Screen> from the <Auto Adjustment> menu, and press
.
The <Auto Adjustment> menu appears.
(2) Choose <Execute> with
or
, and press
.
background (wallpaper, etc.) is in use.
• This function does not work correctly
with some graphics boards.
Flickering, screen position, and screen size are corrected by the auto-
adjustment function.
• “Auto in Progress” appears on the
screen during auto adjustment.
If the screen is not displayed correctly even after adjusting in step
1 above, perform the adjustments according to the procedures on
the following pages. When the screen is displayed correctly, go to
step 5 “To adjust color gradation automatically [Range]”.
Prepare the display pattern for the analog display adjustment.
NOTE
2
• For how to open and contents of the
screen adjustment pattern files, refer
to “Readme.txt”.
Load the “EIZO LCD Utility Disk” to your PC, and then open the screen
adjustment pattern files.
Chapter 2 Settings and Adjustments
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Perform the auto adjustment again with the analog screen
adjustment pattern displayed.
3
● To adjust flickering, screen position, and screen size
automatically [Screen]
(1) Display Pattern 1 of the screen adjustment pattern files in full
screen on the monitor.
(2) Choose <Screen> from the <Auto Adjustment> menu, and press
.
The <Auto Adjustment> menu appears.
(3) Choose <Execute> with
or
, and press
.
Flickering, screen position, and screen size are corrected by the auto-
adjustment function.
If the screen is not displayed correctly even after adjusting in step
3 above, perform the adjustments according to the procedures on
the following pages. When the screen is displayed correctly, go to
step 5 “To adjust color gradation automatically [Range]”.
NOTE
Perform advanced adjustments for the following using the
<Screen> menu of the Adjustment menu.
4
• Press the control button slowly so as
not to miss the adjustment point.
• When blurring, flickering or bars
appear on the screen after adjustment,
proceed to [Phase] to remove
flickering or blurring.
Adjust the clock, phase and position, in this order.
● To eliminate vertical bars [Clock]
(1) Choose <Clock> from the <Screen> menu, and press
The <Clock> menu appears.
.
(2) Adjust the clock with
or
, and press
.
The adjustment is completed.
Attention
● To remove flickering or blurring [Phase]
• Flickering or blurring may not be
eliminated depending on your PC or
graphics board.
Adjustable range: 0 to 63
(1) Choose <Phase> from the <Screen> menu, and press
The <Phase> menu appears.
.
(2) Adjust the phase with
or
, and press
.
NOTE
The adjustment is completed.
• When vertical bars appear on the
screen after adjustment, go back to
“To eliminate vertical bars [Clock]”.
(Clock → Phase → Position)
Chapter 2 Settings and Adjustments
15
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE
● To correct screen position [Position]
(1) Choose <Position> from the <Screen> menu, and press
The <Position> menu appears.
• Since the number of pixels and the
pixel positions are fixed on the LCD
monitor, only one position is provided
to display images correctly. The
position adjustment is made to shift
an image to the correct position.
.
(2) Adjust the position with
/
/
/
to display the image
properly in the display area of the monitor, and press
The adjustment is completed.
Adjust the color gradation.
5
● To adjust color gradation automatically [Range]
Every color gradation (0 to 255) can be displayed by adjusting the
signal output level.
(1) Display Pattern 2 of the screen adjustment pattern files in full
screen on the monitor.
(2) Choose <Range> from the <Auto Adjustment> menu, and press
.
(3) Choose “Execute” with
or
, and press
.
The output range is adjusted automatically.
(4) Close the Pattern 2.
Modify blurred characters or lines.
6
Attention
● To modify blurred characters/lines [Smoothing]
When a image is displayed with a resolution other than the
recommendation, the characters or lines of the displayed image may be
blurred.
• Smoothing setting may not be required
depending on the display resolution.
(You cannot choose the smoothing
icon.)
Adjustable range: 1 to 5
(1) Choose <Screen> from the Adjustment menu, and press
(2) Choose <Smoothing> from the <Screen> menu, and press
The <Smoothing> menu appears.
.
.
(3) Adjust the characters/lines with
The adjustment is completed.
or
, and press
.
Chapter 2 Settings and Adjustments
16
Download from Www.Somanuals.com. All Manuals Search And Download.
2-3 Color Adjustment
●
To select the display mode (FineContrast mode)
FineContrast allows you to select the best display mode easily according to the
monitor’s application.
FineContrast mode
Mode
Custom
Purpose
Available to change all setting values.
Allows the brightness to be set lower than possible with
other modes.
EyeCare
sRGB
Text
Suitable for color matching with sRGB compatible
peripherals.
Suitable for displaying texts for word processing or
spreadsheets.
Suitable for displaying images such as photos or picture
images.
Picture
Movie
Suitable for playing back animated images.
Displays the
current mode.
NOTE
(1) Press
.
• The Adjustment menu and the
FineContrast mode name cannot be
displayed at the same time.
• “ScreenManager Pro for LCD”
allows you to select the FineContrast
mode automatically according to the
application used.
The FineContrast mode name appears at the lower left of the screen.
(2) One of five modes is displayed in turn each time
is pressed.
Custom EyeCare
sRGB Text Picture Movie
(Refer to “Chapter 3 Auto
FineContrast” on the User’s Manual
for “ScreenManager Pro for LCD”.)
Chapter 2 Settings and Adjustments
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Attention
●
To perform advanced adjustments
• Wait 30 minutes or more from
monitor power on before starting the
color adjustment.
Independent setting and saving of color adjustment are available for each
FineContrast mode.
• Perform the range adjustment first
when adjusting color for analog input
signals.
●
Adjustment items in each mode
According to the FineContrast mode selected, the adjustable function differs.
(Refer to “To adjust color gradation
• The same image may be seen in
different colors on multiple monitors
due to their monitor-specific
characteristics. Make fine color
adjustment visually when matching
colors on multiple monitors.
: Adjustment available −: Invalid for adjustment
√
FineContrast mode
Icon
Function
Custom EyeCare sRGB
Text
Picture Movie
Brightness
Contrast
Temperature
Gamma
Saturation
Hue
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
−
√
√
√
√
√
√
−
−
−
−
−
−
√
NOTE
• The values shown in “%” or “K” are
available only as reference.
−
√
−
√
• Using the “ScreenManager Pro for
LCD” allows you to perform the color
adjustment by using the mouse and
keyboard of your PC. The adjusted
status can be registered as a color data
and restore the data later. (Refer to
“Chapter 4 Color Adjustment” on the
User’s Manual for “ScreenManager
Pro for LCD”.)
√
√
Gain
−
−
−
Reset
√
√
√
●
To adjust the brightness [Brightness]
NOTE
The screen brightness is adjusted by changing the brightness of the backlight
(Light source from the LCD back panel).
• You can also adjust the brightness
by pressing
or
without
displaying the adjustment menu.
• When FineContrast is set to the
[EyeCare] mode and Brightness is
lowered to its minimum value, any
further adjustments will automatically
be transfered to Contrast. When
transferred to Contrast adjustment the
color of the value in the adjustment
menu will change.
Adjustable range: 0 to 100%
(1) Choose <Color> from the Adjustment menu, and press
(2) Choose <Brightness> from the <Color> menu, and press
The <Brightness> adjustment menu appears.
.
.
(3) Adjust the brightness with
The adjustment is completed.
or
, and press
.
●
To adjust the contrast [Contrast]
NOTE
The luminance of the screen is adjusted by varying the video signal level.
Adjustable range: 0 to 100%
• In the contrast of 50%, every color
gradation is displayed.
• When adjusting the monitor, it
is recommended to perform the
brightness adjustment which may
not lose the gradation characteristics,
prior to the contrast adjustment.
Perform the contrast adjustment in the
following cases.
(1) Choose <Color> from the Adjustment menu, and press
(2) Choose <Contrast> from the <Color> menu, and press
The <Contrast> adjustment menu appears.
.
.
(3) Adjust the contrast with
The adjustment is completed.
or
, and press
.
– When you feel the image is dark
even if the brightness is set to
100%. (Set the contrast to higher
than 50%).
– When you feel the image is bright
even if the brightness is set to 0%.
(Set the contrast to lower than
50%).
Chapter 2 Settings and Adjustments
18
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE
●
To adjust the color temperature [Temperature]
• You cannot adjust the value if the
icon is not displayed, depending on
the FineContrast mode selected. (See
“Adjustment items in each mode” on
page 18.)
• [Gain] allows you to perform more
advanced adjustment (See “To adjust
• If you set to [Off], the image is
displayed in the preset color of the
monitor (Gain: 100% for each RGB).
• When changing the gain value, the
color temperature adjusting range is
changed to “Off”.
The color temperature can be adjusted. The color temperature is normally used
to express the hue of “White” and/or “Black” by a numerical value. The value
is expressed in degrees “K” (Kelvin).
In the same way as the flame temperature, the image on the monitor is displayed
reddish if the color temperature is low and is bluish if the color temperature is
high. The gain preset values are set for each color temperature setting value.
5000K
The white color image is displayed reddish. The 5000K or 6000K
is usually used in the printing industry.
6500K
The white color image is displayed in warm white like paper white.
The temperature is suitable to display photographs or video
images.
9300K
The white color image is displayed slightly bluish white.
Adjustable range: Off, 4000K-10000K (specified by every 500K unit,
including 9300K)
(1) Choose <Color> from the Adjustment menu, and press
(2) Choose <Temperature> from the <Color> menu, and press
The <Temperature> adjustment menu appears.
.
.
(3) Adjust the color temperature with
The adjustment is completed.
or
, and press
.
NOTE
●
To adjust the gamma value [Gamma]
• You cannot adjust the value if the
icon is not displayed, depending on
the FineContrast mode selected. (See
“Adjustment items in each mode” on
page 18.)
The gamma value can be adjusted. The luminance of the monitor varies
depending on the input signal, however, the variation rate is not proportional to
the input signal. To keep the balance between the input signal and the luminance
of the monitor is called as “Gamma correction”.
Adjustable range: 1.8, 2.0, 2.2
(1) Choose <Color> from the Adjustment menu, and press
(2) Choose <Gamma> from the <Color> menu, and press
The <Gamma> adjustment menu appears.
.
.
(3) Adjust the gamma value with
The adjustment is completed.
or
, and press
.
Attention
●
To adjust the color saturation [Saturation]
• This function does not enable to
display every color gradation.
This function allows you to adjust the saturation of the color on the monitor.
Adjustable range: -128 to 127
NOTE
• You cannot adjust the value if the
icon is not displayed, depending on
the FineContrast mode selected. (See
“Adjustment items in each mode” on
page 18.)
(1) Choose <Color> from the Adjustment menu, and press
(2) Choose <Saturation> from the <Color> menu, and press
The <Saturation> adjustment menu appears.
.
.
(3) Adjust the saturation of the color with
The adjustment is completed.
or
, and press
.
• Setting the minimum (-128) turns the
image to a monochrome screen.
Chapter 2 Settings and Adjustments
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Attention
●
To adjust the hue [Hue]
• This function does not enable to
display every color gradation.
This function allows you to adjust the hue. If you set the hue to a high value,
the image turns greenish. If low, the image turns purplish.
Adjustable range: -32 to 32
NOTE
• You cannot adjust the value if the
icon is not displayed, depending on
the FineContrast mode selected. (See
“Adjustment items in each mode” on
page 18.)
(1) Choose <Color> from the Adjustment menu, and press
.
(2) Choose <Hue> from the <Color> menu, and press
The <Hue> adjustment menu appears.
.
(3) Adjust the hue with
or
, and press
.
The adjustment is completed.
Attention
●
To adjust the gain value [Gain]
• This function does not enable to
display every color gradation.
Each luminance of red/green/blue composing the color is called “Gain”. The
gain adjustment may change the color tone of the “White” (when the max input
signal for each color is obtained)
NOTE
• You cannot adjust the value if the
icon is not displayed, depending on
the FineContrast mode selected. (See
“Adjustment items in each mode” on
page 18.)
• The gain value may change depending
on the value of the color temperature.
• When changing the gain value, the
color temperature adjusting range is
changed to “Off”.
Adjustable range: 0 to 100%
(1) Choose <Color> from the Adjustment menu, and press
(2) Choose <Gain> from the <Color> menu, and press
The <Gain> adjustment menu appears.
.
.
(3) Adjust the respective value of Red, Green or Blue with
or
, and press
.
The adjustment is completed.
NOTE
2-4 Adjusting Volume [Volume]
This function allows you to adjust volume up or down.
Adjustable range: 0 to 20
• You can also adjust volume by
pressing
displaying the adjustment menu.
• The volume for the DisplayPort
and the stereo mini jack can be set
individually.
or
without
(1) Choose <Sound> from the Adjustment menu, and press
(2) Choose <Volume> from the <Sound> menu, and press
The volume adjustment menu appears.
.
.
(3) Adjust the volume with
The adjustment is completed.
or
, and press
.
2-5 Switching sound source during
DisplayPort signal input [Source]
This function allows you to switch sound source during DisplayPort signal
input. You can select the DisplayPort or Stereo Mini Jack.
NOTE
• This function is available with
DisplayPort input.
(1) Choose <Sound> from the Adjustment menu, and press
(2) Choose <Source> from the <Sound> menu, and press
The Source adjustment menu appears.
.
.
(3) Select “DisplayPort” or “Stereo Mini Jack” with
The setting is completed.
or
, and press
.
Chapter 2 Settings and Adjustments
20
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE
2-6 Turning off the audio output at Power
Saving mode [Power Save]
• No audio is output while the monitor
is in the Power Saving mode, if
input signal and sound source are of
DisplayPort.
This monitor allows you to turn off the audio output from the speakers/
headphone at the power saving mode.
(1) Choose <Sound> from the Adjustment menu, and press
(2) Choose <Power Save> from the <Sound> menu, and press
The <Power Save> setting menu appears.
.
.
(3) Select “On” or “Off” with
The setting is completed.
or
, and press
.
NOTE
2-7 Setting On/Off for the automatic
brightness adjustment function
[Auto EcoView]
• Be careful not to block the sensor on
the lower side of the monitor when
using the Auto EcoView function.
The sensor on the front side of the monitor detects the environmental brightness
to adjust the screen brightness automatically and comfortably by using the Auto
EcoView function.
(1) Press
.
The <Auto EcoView> setting menu appears.
(2) The On/Off setting is toggled by pressing
.
2-8 Setting On/Off for Power Saving mode
[Power Save]
This function allows you to set the monitor into the power saving mode
according to the PC status.
(1) Choose <PowerManager> from the Adjustment menu, and press
(2) Choose <Power Save> from the <PowerManager> menu, and press
The <Power Save> setting menu appears.
.
.
(3) Select “On” or “Off” with
The setting is completed.
or
, and press
.
■
Analog input
This monitor complies with the VESA DPMS standard.
Attention
• Turning off the main power switch
or unplugging the power cord
completely shuts off power supply to
the monitor.
• Devices connected to the USB port
(upstream and downstream) work
when the monitor is in power saving
mode or when the power button of
the monitor is Off. Therefore, power
consumption of the monitor varies
with connected devices even in the
power saving mode.
[Power Saving System]
Power
Indicator
PC
Monitor
Operating
Operating
Power saving
Blue
Orange
Power saving
STAND-BY
SUSPENDED
OFF
■
Digital input
• DVI-D
This monitor complies with the DVI DMPM standard.
• DisplayPort
This monitor complies with the DisplayPort Standard V1.1a.
• Power consumption varies even
when the stereo mini jack cable is
connected.
Chapter 2 Settings and Adjustments
21
Download from Www.Somanuals.com. All Manuals Search And Download.
[Power Saving System]
The monitor enters the power saving mode in five seconds in connection with
the PC setting.
PC
Monitor
Operating
Power saving
Power Indicator
Blue
Orange
Operating
Power saving
2-9 Turning off the monitor automatically
[Off Timer]
This function allows you to switch the setting to turn off the monitor
automatically after a specified time has passed at the power saving mode.
Adjustable range: Disable, Enable (0, 1, 2, 3, 5, 10, 15, 20, 25, 30, 45 min,
1-5h)
(1) Choose <PowerManager> from the Adjustment menu, and press
(2) Choose <Off Timer> from the <PowerManager> menu, and press
The <Off Timer> setting menu appears.
.
.
(3) Select “Enable” or “Disable” with
or
.
When selecting “Enable”, set a monitor Off time with
or
.
(4) Press
.
The setting is completed.
NOTE
2-10 Displaying the level of power saving by
EcoView Index
• EcoView Index appears when
adjusting brightness or switching the
FineContrast mode, etc.
You can switch the on/off setting
of displaying EcoView Index in
<EcoView Index> menu from the
<PowerManager> menu. (Only when
the orientation of the adjustment
menu is set to "Landscape")
This function allows you to display the power saving level by green indicator.
The power saving ratio comes to high as the indicator level meter lights towards
right.
(1) Press
.
The EcoView Index menu appears.
Chapter 2 Settings and Adjustments
22
Download from Www.Somanuals.com. All Manuals Search And Download.
2-11 Screen Size Selection
●
To change screen size [Screen Size]
The image with the resolution other than the recommended resolution is
displayed in full screen automatically. You can change the screen size by using
<Screen Size> from <Others> menu.
Menu
Function
Displays an image in full screen. Images are distorted in
some cases because the vertical rate is not equal to the
horizontal rate.
Full Screen
(default setting)
Displays an image in full screen. In some cases, a blank
horizontal or vertical border appears to equalize the vertical
rate and the horizontal rate.
Enlarged
Normal
Displays images with the specified resolution.
Example: Image size 1280 x 1024 in case of S2243W
Full Screen
(Default setting)
Normal
Enlarged
(1920 1200)
(1500 1200)
(1280 1024)
×
×
×
(1) Choose <Others> from the Adjustment menu, and press
(2) Choose <Screen Size> from the <Others> menu, and press
The screen size setting window appears.
.
.
(3) Select “Full Screen,” “Enlarged,” or “Normal” with
press
or
, and
.
The screen size setting is completed.
●
To adjust brightness of non-display area [Border Intensity]
A border (black area with no image) around the image appears in the “Normal”
or “Enlarged” mode.
Border
(1) Choose <Others> from the Adjustment menu, and press
.
(2) Choose <Border Intensity> from the <Others> menu, and press
The <Border Intensity> menu appears.
.
(3) Adjust border intensity with
or
, and press
.
The border intensity adjustment is completed.
Chapter 2 Settings and Adjustments
23
Download from Www.Somanuals.com. All Manuals Search And Download.
2-12 Setting Adjustment Menu Display
●
To update menu settings [Menu Size/Menu Position/Menu
Off Timer/Translucent]
Menu Size
Change the Adjustment menu size using the following procedure.
(1) Choose <Others> from the Adjustment menu, and press
.
(2) Choose <Menu Settings> from the <Others> menu, and press
.
(3) Choose <Menu Size> from the <Menu Settings> menu, and press
The <Menu Size> menu appears.
.
(4) Select “Normal” or “Enlarged” with
The setting is completed.
or
, and press
.
Menu Position
Adjust the menu position using the following procedure.
(1) Choose <Others> from the Adjustment menu, and press
.
(2) Choose <Menu Settings> from the <Others> menu, and press
.
(3) Choose <Menu Position> from the <Menu Settings> menu, and press
The <Menu Position> menu appears.
.
(4) Select a menu position with
The setting is completed.
/
/
/
, and press
.
NOTE
Menu Off Timer
• The display time of the FineContrast
mode and EcoView Index remains
unchanged.
Set the menu display time using the following procedure.
Adjustment range: Disable, Enable (15, 30, 45, 60s)
(1) Choose <Others> from the Adjustment menu, and press
.
(2) Choose <Menu Settings> from the <Others> menu, and press
.
(3) Choose <Menu Off Timer> from the <Menu Settings> menu, and press
The <Menu Off Timer> menu appears.
.
(4) Select “Enable” or “Disable” with
or
.
When selecting “Enable”, choose a time for displaying menu with
.
or
(5) Press
.
The setting is completed.
Translucent
Set the transparency for menu display using the following procedure.
(1) Choose <Others> from the Adjustment menu, and press
.
(2) Choose <Menu Settings> from the <Others> menu, and press
.
(3) Choose <Translucent> from the <Menu Settings> menu, and press
The <Translucent> menu appears.
.
.
(4) Adjust the transparency for menu display with
The setting is completed.
or
, and press
Chapter 2 Settings and Adjustments
24
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE
2-13 Setting Orientation
• For using the monitor with
“Portrait” position, the graphics
board supporting portrait display is
required. When using the monitor
with “Portrait” position, the setting
needs to be changed depending on the
graphics board used in your PC. Refer
to the manual of the graphics board
for details.
●
To set the orientation of the Adjustment menu [Orientation]
This function allows you to change the orientation of the Adjustment menu
when using the monitor screen in vertical display position.
(1) Choose <Others> from the Adjustment menu, and press
(2) Choose <Orientation> from the Others menu, and press
The <Orientation> menu appears.
.
.
(3) Select “Landscape” or “Portrait” with
The setting is completed.
or
, and press
.
(4) When selecting “Portrait”, turn the monitor screen 90° in clockwise
direction.
2-14 Locking Buttons
This function allows you to lock
to prevent changing the adjusted/set status.
(1) Press
(2) Press
to turn off the monitor.
holding down to turn on the monitor.
The Lock/Unlock setting is toggled by performing the operation in step 2.
NOTE
2-15 Displaying Monitor Information
[Information]
• The usage time is not always “0”
when you purchase the monitor due
to factory inspection.
This function allows you to display the input signal status, current resolution
and model name.
Information 1/3 : Input signal status (D-Sub/DVI Digital/DisplayPort),
resolution and H/V frequency
Information 2/3 : Enable/Disable setting for DDC/CI
Information 3/3 : Model name, serial number and usage time
(1) Choose <Information> from the Adjustment menu, and press
The <Information> menu appears.
.
(2) Then, press
to check settings, etc.
Chapter 2 Settings and Adjustments
25
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE
2-16 Enabling/Disabling DDC/CI
communication
• You can check the DDC/CI setting in
the <Information> menu.
This function allows you to enable/disable the DDC/CI communication.
(1) Press
(2) Press
to turn off the monitor.
holding down to turn on the monitor.
The Enable/Disable setting is toggled by performing the operation in step 2.
2-17 Setting Power Indicator ON/OFF
[Power Indicator]
This function allows you to set the power indicator (blue) ON/OFF in the
monitor ON condition.
(1) Choose <Others> from the Adjustment menu, and press
.
(2) Choose <Power Indicator> from the <Others> menu, and press
The <Power Indicator> menu appears.
.
(3) Select “Enable” or “Disable” with
The setting is completed.
or
, and press
.
2-18 Setting Language [Language]
This function allows you to select a language for the adjustment menu or
displaying message.
Selectable languages
English/German/French/Spanish/Italian/Swedish/Simplified Chinese/
Traditional Chinese/Japanese
(1) Choose <Language> menu from the Adjustment menu, and press
The <Language> menu appears.
.
(2) Choose a language with
The setting is completed.
/
/
/
, and press
.
2-19 Setting EIZO logo display ON/OFF
The EIZO logo appears on the display when turning on the monitor. This
function allows you to display, or not, the EIZO logo.
(1) Press
(2) Press
to turn off the monitor.
holding down to turn on the monitor.
The EIZO logo display setting is toggled by performing the operation in step 2.
Chapter 2 Settings and Adjustments
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Attention
2-20 Resuming the Default Setting [Reset]
There are two types of Reset. One is to reset the color adjustment only to the
default settings, and the other is to reset all the settings to the default settings.
• After resetting, you cannot undo the
operation.
●
To reset color adjustment values
Only the adjustment values in the current FineContrast mode will revert to the
default settings (factory settings).
(1) Choose <Color> from the Adjustment menu, and press
(2) Choose <Reset> from the <Color> menu and press
The <Reset> menu appears.
.
.
(3) Select <Reset> with
or
, and press
.
The color adjustment values revert to the default settings.
●
NOTE
To reset all adjustments to the factory default settings
• For main default settings, refer
to “Main default settings (factory
Reset all adjustments to the factory default settings.
(1) Choose <Others> from the Adjustment menu, and press
(2) Choose <Reset> from the <Others> menu, and press
The <Reset> menu appears.
.
.
(3) Select <Reset> with
or
, and press
.
All setting values revert to the default settings.
Chapter 2 Settings and Adjustments
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Connecting Cables
3-1 Connecting More than Two PCs to the
Monitor
More than two PCs can be connected to the monitor through the D-Sub mini 15
pin, the DVI-D and the DisplayPort connector on the back of the monitor.
Connection examples
DisplayPort
connector
D-Sub mini
15-pin Connector
DVI-D connector
To PC 1
D-Sub mini
15-pin Connector
Analog
Signal cable
(supplied MD-C87)
To PC 2
DVI-D connector
Digital
Signal cable
(supplied FD-C39)
To PC 3
DisplayPort connector
Digital
Signal cable
(PP200 option)
●
To switch the input signal
The input signal switches each time
is pressed.
When the signal is switched, the active input port name appears at the top right
corner of the screen.
Chapter 3 Connecting Cables
28
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE
●
To set input signal selection [Input Signal]
• When “Auto” is selected for <Input
Signal>, the monitor’s power-saving
function works only when the two
PCs are in the power-saving mode.
The monitor recognizes the connector through which PC signals are input.
When a PC is turned off or enters the powersaving mode, the monitor
automatically displays another signal.
Priority setting
Auto
Function
When a PC is turned off or enters the powersaving
mode, the monitor automatically displays another
signal.
Manual
The monitor detects only the PC’s signals currently
displaying automatically. Select an active input signal
with
.
[Input signal setting]
(1) Choose <Others> from the Adjustment menu, and press
(2) Choose <Input Signal> from the <Others> menu, and press
The <Input Signal> menu appears.
.
.
(3) Select “Auto” or “Manual” with
The setting is completed.
or
, and press
.
Attention
3-2 Adjusting the DVI Input Level
[DVI Input Level]
• Select "Manual" only if a noise
appears on the screen when using a
DVI long cable.
This function allows you to adjust the DVI signal input level when using a DVI
long cable.
Adjustment range: Auto, Manual (1 to 8)
(1) Press
(2) Press
to turn off the monitor.
holding down to turn on the monitor.
The <DVI Input Level> adjustment menu appears.
(3) Select “Auto” or “Manual” with
or
.
When selecting “Manual”, adjust the input level with
or
to display correctly.
(4) Press
.
The adjustment is completed.
Chapter 3 Connecting Cables
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Attention
3-3 Connecting Peripheral USB Devices
This monitor has a hub compatible with USB. Connected to a PC compatible
with USB or another USB hub, this monitor functions as a USB hub allowing
connection to peripheral USB devices.
• This monitor may not work depending
on PC, OS or peripheral devices
to be used. For USB compatibility
of peripheral devices, contact their
manufactures.
• Devices connected to the USB port
(upstream and downstream) work
when the monitor is in power saving
mode or when the power button of
the monitor is Off. Therefore, power
consumption of the monitor varies
with connected devices even in the
power saving mode.
● Required System Environment
(1) A PC equipped with a USB port or another USB hub connected to
a USB compatible PC
(2) Windows 2000/XP/Vista or Mac OS 9.2.2 and Mac OS X 10.2 or later
(3) EIZO USB cable (MD-C93)
• When the main power switch is Off,
device connected to the USB port will
not operate.
● Connection Procedure (Setup of USB Function)
(1) Connect the monitor first to a PC using the signal cable, and run
the PC.
(2) Connect the supplied USB cable between the downstream USB
port of a USB compatible PC (or another USB hub) and the
monitor’s upstream USB port.
(3) Connect the peripheral USB device to the USB port (downstream)
of the monitor.
Downstream
Upstream
The USB hub function is set up automatically upon connection of
the USB cable.
Chapter 3 Connecting Cables
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 Troubleshooting
If a problem still remains after applying the suggested remedies, contact your local dealer.
• No-picture problems → See No.1 - No.2.
• Imaging problems (digital input) → See No.3 - No.8.
• Imaging problems (analog input) → See No.3 - No.12.
• Other problems → See No.13 - No.16.
• USB problems → See No.17.
Problems
Possible cause and remedy
1. No picture
• Power indicator does not light.
• Check whether the power cord is connected correctly. If
the problem persists, turn off the main power, and then
turn it on again a few minutes later.
• Turn the main power switch on.
• Press
.
• Power indicator lights blue.
• Set each adjusting value in [Brightness], [Contrast] and
• When using the long DVI cable, adjust the DVI input
• Power indicator lights orange.
• Power indicator flashes orange.
• Switch the input signal with
• Operate the mouse or keyboard.
• Check whether the PC is turned on.
.
• There is a problem in the device that uses DisplayPort
connection. Solve the problem, and turn off the main
power of the monitor, and then turn it on again. Refer to
the user’s manual of the device that uses DisplayPort
connection for details.
2. The message below appears.
This message appears when the signal is not input
correctly even when the monitor functions properly.
• This message appears when no signal is input.
Example:
• The message shown left may appear, because some
PCs do not output the signal soon after power-on.
• Check whether the PC is turned on.
• Check whether the signal cable is connected properly.
• Switch the input signal with
.
• When using the long DVI cable, adjust the DVI input
• The message shows that the input signal is out of the • Check whether the signal setting of your PC matches
specified frequency range. (Such signal frequency is
displayed in red.)
Example:
the resolution and the vertical frequency settings for the
• Reboot the PC.
• Select an appropriate display mode using the graphics
board’s utility. Refer to the manual of the graphics board
for details.
fD : Dot Clock
(Displayed only when the digital signal inputs)
fH : Horizontal Frequency
fV : Vertical Frequency
3. The screen is too bright or too dark.
• Adjust using [Brightness] or [Contrast]. (The LCD
monitor backlight has a fixed life span. When the screen
becomes dark or begins to flicker, contact your local
Chapter 4 Troubleshooting
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Problems
4. Characters are blurred.
Possible cause and remedy
• Check whether the signal setting of your PC matches
the resolution and the vertical frequency settings for the
5. Afterimages appear.
• Use a screen saver or off timer function for a long-time
image display.
• Afterimages are particular to LCD monitors. Avoid
displaying the same image for a long time.
6. Green/red/blue/white dots or defective dots remain • This is due to LCD panel characteristics and is not a
on the screen. failure.
7. Interference patterns or pressure marks remain on • Leave the monitor with a white or black screen. The
the screen.
symptom may disappear.
8. Noise appears on the screen.
• When entering the signals of analog input, change the
setting to “On” in <Signal Filter> from the <Screen>
menu.
• When entering the signals of HDCP system, the normal
images may not be displayed immediately.
• When using the long DVI cable, adjust the DVI input
9. Display position is incorrect.
• Adjust image position so that it is displayed properly
• If the problem persists, use the graphics board’s utility if
available to change the display position.
image is flickering.
11. Whole screen is flickering or blurring.
12. Upper part of the screen is distorted as shown
below.
• This is caused when both composite sync (X-OR)
signal and separate vertical sync signal are input
simultaneously. Select either composite signal or
separate signal.
13. The <Smoothing> icon on the Adjustment menu
<Screen> cannot be selected.
• Smoothing setting may not be required depending on the
display resolution. (You cannot choose the smoothing
icon.)
• <Smoothing> is disabled when the screen is displayed in
the following resolutions.
• 1680 × 1050 (S2233W)
• 1920 × 1200 (S2243W)
• Select [Enlarged] during <Screen Size> in the
resolution of 1600 × 1200. (S2243W)
• Select [Normal] during <Screen Size>.
14. The adjustment menu does not appear.
• Check whether the operation lock function works.
15. The auto adjust function does not work correctly.
• This function does not work when digital signal is input.
• This function does not work correctly with some graphics
boards.
Chapter 4 Troubleshooting
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Problems
Possible cause and remedy
16. No audio output.
• Check whether the mini jack cable is correctly connected.
• Check whether volume is set to 0.
• Check the setting of the PC and the audio playback
software.
• During DisplayPort signal input, check the [Source]
17. The monitor connected with the USB cable is not
detected. / USB devices connected to the monitor
does not work.
• Check whether the USB cable is connected correctly.
• Change the USB port to another one. If the PC or
peripheral devices works correctly by changing the USB
port, contact your local dealer. (Refer to the manual of
the PC for details.)
• Reboot the PC.
• If the peripheral devices work correctly when the PC and
peripheral devices are connected directly, please contact
your local dealer.
• Check whether the PC and OS are USB compliant. (For
USB compliance of the respective devices, consult their
manufacturers.)
• Check the PC’s BIOS setting for USB when using
Windows. (Refer to the manual of the PC for details.)
Chapter 4 Troubleshooting
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 Reference
5-1 Attaching an Arm
Attention
The stand can be removed and replaced with an arm (or another stand) to be
attached to the monitor. Use an arm or stand of EIZO option.
• When attaching an arm or stand,
follow the instructions of their user’s
manual.
• When using another manufacturer’s
arm or stand, confirm the following in
advance and select one conforming to
the VESA standard.
Lay the LCD monitor on a soft cloth spread over on a stable
surface with the panel surface facing down.
1
– Clearance between the screw holes:
100 mm × 100 mm
Remove the stand. (Prepare a screwdriver.)
2
– Thickness of plate: 2.6 mm
– Strong enough to support weight of
the monitor unit (except the stand)
and attachments such as cables.
Use the screws as described below.
– EZ-UP stand
Free mount type:
The screws supplied with this
monitor (M4 × 12mm)
Unscrew the four screws securing the unit and the stand with the
screwdriver.
Attach the monitor to the arm or stand.
3
Secure the monitor to the arm or stand using the screws specified in the
user’s manual of the arm or stand.
– FlexStand
Height adjustable stand:
The screws fixing the stand to the
monitor
• When using an arm or stand, attach it
to meet the following tilt angles of the
monitor.
– Up 45 degrees, down 45 degrees
(horizontal display, and vertical
display rotated 90 degrees
clockwise)
• Connect the cables after attaching an
arm.
• If you need to remove the EZ-UP
stand, turn the panel on the monitor
to the left and right a little to appear
the four screws positioned under the
stand. Then unscrew the four screws.
Chapter 5 Reference
34
Download from Www.Somanuals.com. All Manuals Search And Download.
5-2 Folding the EZ-UP stand
Perform the following procedures to fold the stand when re-packing a monitor
with an EZ-UP stand.
Remove the cable holder.
1
Lower the monitor screen position until the hinge of the stand
touches the stand base, and attach the lock metal fitting.
2
Adjust the monitor angle so as the monitor screen not to touch the stand
base.
Lock metal fitting
Hinge
Stand Base
Fall the monitor screen backward with keeping slide-up the
“Unlock” knob.
3
When maximally tilting (25º) the monitor screen backward, the “Unlock”
knob may be hard to be slid-up. Then, slightly tilt up the monitor to
vertical direction and slide-up the “Unlock” knob.
“Unlock” knob
Chapter 5 Reference
35
Download from Www.Somanuals.com. All Manuals Search And Download.
5-3 Specifications
S2233W
LCD Panel
22.0-inch (560 mm) TFT color LCD with anti-glare hard coating
Viewing angle: Horizontal 178°, Vertical 178° (CR:10 or more)
Dot Pitch
0.282 mm
Horizontal Scan Frequency
Analog: 31-82 kHz
Digital (DVI-D/DisplayPort) : 31-65 kHz
Vertical Scan Frequency
Analog: 55-76 Hz (Non-interlace)
(1680 × 1050: 55-61 Hz)
Digital (DVI-D/DisplayPort) : 59-61 Hz (Non-interlace)
(VGA TEXT: 69-71 Hz)
Resolution
1680 dots × 1050 lines
Max. Dot Clock
Analog: 150 MHz
Digital (DVI-D/DisplayPort) : 120 MHz
Max. Display Color
Display Area (H × V)
Power Supply
Approx. 16.77 million colors (1064.33 million colors/10bit LUT)
473.8 mm × 296.1 mm
100-120 VAC ±10%, 50/60Hz 0.85A
200-240 VAC ±10%, 50/60Hz 0.43A
Power
Consumption
Screen Display On
Power saving mode
Power button Off
90W or less (with USB load, Speaker working)
80W or less (without USB load, Speaker not working)
1.5W or less (for D-Sub single signal input, without USB load, when stereo
mini jack cable is not connected, [Input Signal] : “Manual”)
1W or less (without USB load, when stereo mini jack cable is not
connected)
Main Power switch Off
0W
Input Signal Connector
D-Sub mini 15-pin
DVI-D connector (Applicable to HDCP)
DisplayPort (Standard V1.1a, applicable to HDCP and 8-bit)
Applicable Format (Audio signal)
- 2ch linear PCM (32 kHz/44.1 kHz/48 kHz/88.2 kHz/96 kHz)
Analog Input Signal (Sync)
Analog Input Signal (Video)
Separate, TTL, positive/ negative
Composite, TTL, positive/ negative
Analog, Positive (0.7Vp-p/75Ω)
TMDS (Single Link)
Digital Signal (DVI-D) Transmission
System
Video Signal Memory
Analog signal: 45 (preset: 16)
Digital signal (DVI-D): 10
Digital signal (DisplayPort): 10
Audio Output
Line input
Speaker output: 0.5W + 0.5W (8Ω, THD: 10% or less)
Headphone output: 2mW + 2mW
Input impedance : 48 kΩ (typ.)
Input level :1.0 Vrms (Max.)
Plug & Play
Analog / Digital (DVI-D) : VESA DDC 2B / EDID structure 1.3
Digital (DisplayPort) : VESA DisplayPort / EDID structure 1.4
Dimensions
(Width) ×
(Height) ×
(Depth)
Main unit (including
Height adjustable stand) (8.2 inch)
511 mm (20.1 inch) × 439 - 521 mm (17.3 - 20.5 inch) × 208.5 mm
Main unit (including EZ- 511 mm (20.1 inch) × 351.5 - 516.5 mm (13.8 - 20.3 inch) × 279.9 -
UP stand)
307.5 mm (11.0 - 12.1 inch)
Main unit (includeing
FlexStand)
511 mm (20.1 inch) × 347.5 - 521.5 mm (13.7 - 20.5 inch) × 240.5 -
256 mm (9.5 - 10.1 inch)
Main unit (without stand) 511 mm (20.1 inch) × 333 mm (13.1 inch) × 85 mm (3.35 inch)
Chapter 5 Reference
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Mass
Main unit (including
Height adjustable stand)
Approx. 9.6 kg (21.2 lbs.)
Main unit (including EZ- Approx. 11.4 kg (25.1 Ibs.)
UP stand)
Main unit (includeing
FlexStand)
Approx. 9.6 kg (21.2 Ibs.)
Main unit (without stand) Approx. 6.6 kg (14.6 lbs.)
Movable range Height adjustable stand Tilt: 40° Up, 0° Down
Swivel: 35° Right, 35° Left
Adjustable height: 82 mm (3.2 inch)
Rotation: 90° (clockwise)
EZ-UP stand
FlexStand
Tilt: 25° Up, 0° Down
Swivel: 172° Right, 172° Left
Adjustable height: 165 mm (6.5 inch)
Rotation: 90° (clockwise)
Tilt: 30° Up, 0° Down
Swivel: 172° Right, 172° Left
Adjustable height: 225 mm (8.9 inch) (Tilt 0°: 174mm (6.9 inch))
Rotation: 90° (clockwise)
Environmental Temperature
Conditions
Operating temperature: 5 °C - 35 °C (41 °F - 95 °F)
Storage temperature: -20 °C - 60 °C (-4 °F - 140 °F)
Humidity
Operating humidity: 20% - 80% R.H. (no condensation)
Storage humidity: 10% - 80% R.H. (no condensation)
Pressure
Operating: 700 to 1,060 hPa
Storage: 200 to 1,060 hPa
USB
Standard
Port
USB Specification Revision 2.0
Upstream port × 1, Downstream port × 2
Downstream: Max. 500mA/1 port
Supply current
S2243W
LCD Panel
22.0-inch (560 mm) TFT color LCD with anti-glare hard coating
Viewing angle: Horizontal 178°, Vertical 178° (CR:10 or more)
Dot Pitch
0.247 mm
Horizontal Scan Frequency
Analog: 31-94 kHz
Digital (DVI-D/DisplayPort) : 31-76 kHz
Vertical Scan Frequency
Analog: 55-76 Hz (Non-interlace)
(1920 × 1200: 55-61 Hz)
Digital (DVI-D/DisplayPort) : 59-61 Hz (Non-interlace)
(VGA TEXT: 69-71 Hz)
Resolution
1920 dots × 1200 lines
Max. Dot Clock
Analog: 202.5 MHz
Digital (DVI-D/DisplayPort) : 162 MHz
Max. Display Color
Display Area (H × V)
Power Supply
Approx. 16.77 million colors (1064.33 million colors/10bit LUT)
473.8 mm × 296.1 mm
100-120 VAC ±10%, 50/60Hz 0.85A
200-240 VAC ±10%, 50/60Hz 0.43A
Chapter 5 Reference
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Power
Consumption
Screen Display On
Power saving mode
Power button Off
90W or less (with USB load, Speaker working)
80W or less (without USB load, Speaker not working)
1.5W or less (for D-Sub single signal input, without USB load, when stereo
mini jack cable is not connected, [Input Signal] : “Manual”)
1W or less (without USB load, when stereo mini jack cable is not
connected)
Main Power switch Off
0W
Input Signal Connector
D-Sub mini 15-pin
DVI-D connector (Applicable to HDCP)
DisplayPort (Standard V1.1a, applicable to HDCP and 8-bit)
Applicable Format (Audio signal)
- 2ch linear PCM (32 kHz/44.1 kHz/48 kHz/88.2 kHz/96 kHz)
Analog Input Signal (Sync)
Analog Input Signal (Video)
Separate, TTL, positive/ negative
Composite, TTL, positive/ negative
Analog, Positive (0.7Vp-p/75Ω)
TMDS (Single Link)
Digital Signal (DVI-D) Transmission
System
Video Signal Memory
Analog signal: 45 (preset: 16)
Digital signal (DVI-D): 10
Digital signal (DisplayPort): 10
Audio Output
Line input
Speaker output: 0.5W + 0.5W (8Ω, THD: 10% or less)
Headphone output: 2mW + 2mW
Input impedance : 48 kΩ (typ.)
Input level :1.0 Vrms (Max.)
Plug & Play
Analog / Digital (DVI-D) : VESA DDC 2B / EDID structure 1.3
Digital (DisplayPort) : VESA DisplayPort / EDID structure 1.4
Dimensions
(Width) ×
(Height) ×
(Depth)
Main unit (including
Height adjustable stand) (8.2 inch)
511 mm (20.1 inch) × 439 - 521 mm (17.3 - 20.5 inch) × 208.5 mm
Main unit (including EZ- 511 mm (20.1 inch) × 351.5 - 516.5 mm (13.8 - 20.3 inch) × 279.9 -
UP stand)
307.5 mm (11.0 - 12.1 inch)
Main unit (includeing
FlexStand)
511 mm (20.1 inch) × 347.5 - 521.5 mm (13.7 - 20.5 inch) × 240.5 -
256 mm (9.5 - 10.1 inch)
Main unit (without stand) 511 mm (20.1 inch) × 333 mm (13.1 inch) × 85 mm (3.35 inch)
Mass
Main unit (including
Height adjustable stand)
Approx. 9.6 kg (21.2 lbs.)
Main unit (including EZ- Approx. 11.4 kg (25.1 Ibs.)
UP stand)
Main unit (includeing
FlexStand)
Approx. 9.6 kg (21.2 lbs.)
Main unit (without stand) Approx. 6.6 kg (14.6 lbs.)
Movable range Height adjustable stand Tilt: 40° Up, 0° Down
Swivel: 35° Right, 35° Left
Adjustable height: 82 mm (3.2 inch)
Rotation: 90° (clockwise)
EZ-UP stand
FlexStand
Tilt: 25° Up, 0° Down
Swivel: 172° Right, 172° Left
Adjustable height: 165 mm (6.5 inch)
Rotation: 90° (clockwise)
Tilt: 30° Up, 0° Down
Swivel: 172° Right, 172° Left
Adjustable height: 225 mm (8.9 inch) (Tilt 0°: 174mm (6.9 inch))
Rotation: 90° (clockwise)
Chapter 5 Reference
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Environmental Temperature
Conditions
Operating temperature: 5 °C - 35 °C (41 °F - 95 °F)
Storage temperature: -20 °C - 60 °C (-4 °F - 140 °F)
Humidity
Operating humidity: 20% - 80% R.H. (no condensation)
Storage humidity: 10% - 80% R.H. (no condensation)
Pressure
Operating: 700 to 1,060 hPa
Storage: 200 to 1,060 hPa
USB
Standard
Port
USB Specification Revision 2.0
Upstream port × 1, Downstream port × 2
Downstream: Max. 500mA/1 port
Supply current
Main default settings (factory settings)
Auto EcoView
On
Smoothing
3
FineContrast Mode
PowerManager
Custom
On
Input Signal
Manual
Full Screen
Disable
Normal
Screen Size
Off Timer
Menu Settings
Menu Size
Menu Off Timer
45 sec
Language
English
Chapter 5 Reference
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Outside Dimensions
S2233W/S2243W (Height adjustable stand)
481.5(19)
168(6.6)
unit : mm (inch)
SWIVEL
240.5(9.5)
325(12.8)
264.5(10.4)
511(20.1)
475.8(18.7)
17.6(0.69)
17.6(0.69)
205.5(8.1)
100(3.9)
205.5(8.1)
PIVOT
20
(0.79)
208.5(8.2)
S2233W/S2243W (EZ-UP stand)
481.5(1.9)
129.3(5.1)
unit : mm (inch)
SWIVEL
(220)
511(20.1)
(208.5)
17.6(0.69)
475.8(18.7)
17.6(0.69)
205.5(8.1)
100(3.9)
205.5(8.1)
PIVOT
64.3
(2.53)
27.5
(1.08)
φ272(10.7)
279.9(11)
307.5(12.1)
Chapter 5 Reference
40
Download from Www.Somanuals.com. All Manuals Search And Download.
S2233W/S2243W (FlexStand)
481.5 (18.0)
unit : mm (inch)
SWIVEL
511 (20.1)
285 (11.2)
17.6 (0.69)
17.6 (0.69)
475.8 (18.7)
205.5 (8.1)
100 (3.9)
205.5 (8.1)
235 (9.3)
PIVOT
36.2 (1.43)
235.5 (9.3)
256 (10.1)
240.5 (9.5)
φ220
Chapter 5 Reference
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Connector Pin Assignment
• DVI-D connector
Pin No.
Signal
T.M.D.S. Data 2-
T.M.D.S. Data 2+
T.M.D.S. Data2/4 Shield
NC*
Pin No.
9
Signal
T.M.D.S. Data1-
Pin No.
17
Signal
T.M.D.S. Data0-
1
2
3
4
5
6
7
10
T.M.D.S. Data1+
T.M.D.S. Data1/3 Shield
NC*
18
T.M.D.S. Data0+
T.M.D.S. Data0/5 Shield
NC*
11
19
12
20
NC*
13
NC*
21
NC*
DDC Clock (SCL)
DDC Data (SDA)
14
+5V Power
22
T.M.D.S. Clock shield
T.M.D.S. Clock+
15
Ground (return for +5V,
Hsync, and Vsync)
23
8
NC*
16
Hot Plug Detect
24
T.M.D.S. Clock-
(NC*: No Connection)
• D-Sub mini 15-pin connector
Pin No.
Signal
Pin No.
Signal
Red video ground
Green video ground
Blue video ground
NC*
Pin No.
11
Signal
NC*
1
2
3
4
5
Red video
6
7
Green video
Blue video
NC*
12
Data (SDA)
H. Sync
8
13
9
14
V. Sync
Ground
10
Ground
15
Clock (SCL)
(NC*: No Connection)
• DisplayPort connector
19 17 15 13 11
9
7
5
3
1
20 18 16 14 12 10
8
6
4
2
Pin No.
Signal
Pin No.
8
Signal
Ground
Pin No.
15
Signal
AUX CH+
ML Lane3-
Ground
1
2
3
4
5
6
7
ML Lane1+
ML Lane0-
Ground
Ground
9
16
ML Lane3+
ML Lane2-
Ground
AUX CH-
10
17
Hot Plug Detect
Return
11
18
ML Lane0+
CONFIG1
CONFIG2
12
19
ML Lane2+
ML Lane1-
DP PWR
13
20
14
Chapter 5 Reference
42
Download from Www.Somanuals.com. All Manuals Search And Download.
• USB port
Upstream
Upstream
Series B connector
Series A connector
Contact No. Signal
Remarks
VCC
Cable power
Serial data
Serial data
Cable ground
1
2
3
4
– Data
+ Data
Ground
Accessories List
Cleaning Kit
EIZO ScreenCleaner
*
Speaker Unit
i•Sound L3
PP200
Signal Cable
* May not allowed to attach the option speaker depending on the stand type.
For the latest information about the accessories, refer to our web site.
Chapter 5 Reference
43
Download from Www.Somanuals.com. All Manuals Search And Download.
5-4 Glossary
Clock
The analog input monitor needs to reproduce a clock of the same frequency as the dot clock of the graphics system in
use, when the analog input signal is converted to a digital signal for image display.
This is called clock adjustment. If the clock pulse is not set correctly, some vertical bars appear on the screen.
DDC/CI (Display Data Channel/Command Interface)
VESA provides the standardization for the interactive communication of the setting information, etc. between a PC
and the monitor.
DisplayPort
VESA provides the digital interface standard for the digital display device. DisplayPort can transfer the video signal
up to 16 bits for each channel of RGB, and the audio signal too. (This monitor supports the 8-bit video signal only.)
DVI (Digital Visual Interface)
DVI is a digital interface standard. DVI allows direct transmission of the PC’s digital data without loss.
This adopts the TMDS transmission system and DVI connectors. There are two types of DVI connectors. One is
a DVI-D connector for digital signal input only. The other is a DVI-I connector for both digital and analog signal
inputs.
DVI DMPM (DVI Digital Monitor Power Management)
DVI DMPM is a digital interface power-saving function. The “Monitor ON (operating mode)” and “Active Off
(power-saving mode)” are indispensable for DVI DMPM as the monitor’s power mode.
Gain
This is used to adjust each color parameter for red, green and blue. An LCD monitor displays the color by the light
passing through the panel color filter. Red, green and blue are the three primary colors. All the colors on the screen
are displayed by combining these three colors. The color tone can be changed by adjusting the light intensity (volume)
passing through each color’s filter.
Gamma
Generally, the monitor brightness varies nonlinearly with the input signal level, which is called “Gamma
Characteristic”. A small gamma value produces a low-contrast image, while a large gamma value produces a high-
contrast image.
HDCP (High-bandwidth Digital Contents Protection)
Digital signal coding system developed to copy-protect the digital contents, such as video, music, etc. This helps
to transmit the digital contents safely by coding the digital contents sent via DVI terminal on the output side and
decoding them on the input side.
Any digital contents cannot be reproduced if both of the equipments on the output and input sides are not applicable
to HDCP system.
Phase
Phase means the sampling timing to convert the analog input signal to a digital signal. Phase adjustment is made to
adjust the timing. It is recommended that phase adjustment be made after the clock is adjusted correctly.
Range Adjustment
Range adjustment controls the signal output levels to display every color gradation. It is recommended that range
adjustment be made before color adjustment.
Chapter 5 Reference
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Resolution
The LCD panel consists of numerous pixels of specified size, which are illuminated to form images. This monitor
consists of 1680 (S2233W) / 1920 (S2243W) horizontal pixels and 1050 (S2233W) / 1200 (S2243W) vertical pixels.
At a resolution of 1680×1050 (S2233W) / 1920×1200 (S2243W), all pixels are illuminated as a full screen (1:1).
sRGB (Standard RGB)
International standard for “color reproduction and color space” among peripheral devices (such as monitors, printers,
digital cameras, scanners). sRGB allows Internet users to closely match colors as a simple color matching means for
the Internet use.
Temperature
Color temperature is a method to measure the white color tone, generally indicated in degrees Kelvin. The screen
becomes reddish at a low temperature, and bluish at a high temperature, like the flame temperature.
5000K: Slightly reddish white
6500K: Warm white like paper white
9300K: Slightly bluish white
TMDS (Transition Minimized Differential Signaling)
A signal transmission system for digital interface.
VESA DPMS (Video Electronics Standards Association - Display Power Management Signaling)
VESA provides the standardization of signals from PC (graphics board) for power saving of PC monitors. DPMS
defines the signal status between PC and monitor.
Chapter 5 Reference
45
Download from Www.Somanuals.com. All Manuals Search And Download.
5-5 Preset Timing
The following table shows factory preset video timing (for analog signal only).
Attention
• Display position may be deviated
depending on the PC connected,
which may require screen adjustment
using Adjustment menu.
Frequency
Mode
Dot clock
Horizontal: kHz Polarity
Vertical: Hz
Horizontal
Vertical
Horizontal
Vertical
Horizontal
Vertical
Horizontal
Vertical
Horizontal
Vertical
Horizontal
Vertical
Horizontal
Vertical
Horizontal
Vertical
Horizontal
Vertical
Horizontal
Vertical
Horizontal
Vertical
Horizontal
Vertical
Horizontal
Vertical
Horizontal
Vertical
Horizontal
Vertical
Horizontal
Vertical
31.47
59.94
31.47
70.09
37.86
72.81
37.50
75.00
35.16
56.25
37.88
60.32
48.08
72.19
46.88
75.00
48.36
60.00
56.48
70.07
60.02
75.03
67.50
75.00
60.00
60.00
63.98
60.02
79.98
75.03
75.00
60.00
81.25
65.00
87.50
70.00
93.75
75.00
65.29
59.95
Negative
Negative
Negative
Positive
Negative
Negative
Negative
Negative
Positive
Positive
Positive
Positive
Positive
Positive
Positive
Positive
Negative
Negative
Negative
Negative
Positive
Positive
Positive
Positive
Positive
Positive
Positive
Positive
Positive
Positive
Positive
Positive
Positive
Positive
Positive
Positive
Positive
Positive
Negative
Positive
• If a signal other than those listed in
the table is input, adjust the screen
using the Adjustment menu. However,
screen display may still be incorrect
even after the adjustment.
• When interlace signals are used, the
screen cannot be displayed correctly
even after screen adjustment using the
Adjustment menu.
VGA 640×480@60Hz
25.2 MHz
28.3 MHz
31.5 MHz
31.5 MHz
36.0 MHz
40.0 MHz
50.0 MHz
49.5 MHz
65.0 MHz
75.0 MHz
78.8 MHz
108.0 MHz
108.0 MHz
VGA TEXT
720×400@70Hz
VESA 640×480@73Hz
VESA 640×480@75Hz
VESA 800×600@56Hz
VESA 800×600@60Hz
VESA 800×600@72Hz
VESA 800×600@75Hz
VESA 1024×768@60Hz
VESA 1024×768@70Hz
VESA 1024×768@75Hz
VESA 1152×864@75Hz
VESA 1280×960@60Hz
VESA 1280×1024@60Hz 108.0 MHz
VESA 1280×1024@75Hz 135.0 MHz
VESA 1600×1200@60Hz
162.0 MHz
(S2243W)
Horizontal
Vertical
Horizontal
Vertical
Horizontal
Vertical
Horizontal
Vertical
VESA 1600×1200@65Hz
175.0 MHz
(S2243W)
VESA 1600×1200@70Hz
189.0 MHz
(S2243W)
VESA 1600×1200@75Hz
202.5 MHz
(S2243W)
VESA CVT
1680×1050@60Hz
146.3 MHz
VESA CVT
1920×1200@60Hz
(S2243W)
Horizontal
Vertical
74.56
59.89
74.04
Negative
Positive
Positive
193.3 MHz
154.0 MHz
VESA CVT RB
1920×1200@60Hz
(S2243W)
Horizontal
Vertical
59.95
Negative
Chapter 5 Reference
46
Download from Www.Somanuals.com. All Manuals Search And Download.
For U.S.A. , Canada, etc. (rated 100-120 Vac) Only
FCC Declaration of Conformity
We, the Responsible Party
EIZO NANAO TECHNOLOGIES INC.
5710 Warland Drive, Cypress, CA 90630
Phone: (562) 431-5011
declare that the product
Trade name: EIZO
Model: FlexScan S2233W/S2243W
is in conformity with Part 15 of the FCC Rules. Operation of this product is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures.
* Reorient or relocate the receiving antenna.
* Increase the separation between the equipment and receiver.
* Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
* Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
Note
Use the attached specified cable below or EIZO signal cable with this monitor so as to keep interference within the
limits of a Class B digital device.
- AC Cord
- Shielded Signal Cable (enclosed)
Canadian Notice
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de le classe B est comforme à la norme NMB-003 du Canada.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Hinweise zur Auswahl des richtigen Schwenkarms für Ihren Monitor
Dieser Monitor ist für Bildschirmarbeitsplätze vorgesehen. Wenn nicht der zum Standardzubehör gehörige
Schwenkarm verwendet wird, muss statt dessen ein geeigneter anderer Schwenkarm installiert werden. Bei der
Auswahl des Schwenkarms sind die nachstehenden Hinweise zu berücksichtigen:
Der Standfuß muß den nachfolgenden Anforderungen entsprechen:
a)Der Standfuß muß eine ausreichende mechanische Stabilität zur Aufnahme des Gewichtes vom Bildschirmgerät
und des spezifizierten Zubehörs besitzen. Das Gewicht des Bildschirmgerätes und des Zubehörs sind in der
zugehörenden Bedienungsanleitung angegeben.
b)Die Befestigung des Standfusses muß derart erfolgen, daß die oberste Zeile der Bildschirmanzeige nicht höher
als die Augenhöhe eines Benutzers in sitzender Position ist.
c)Im Fall eines stehenden Benutzers muß die Befestigung des Bildschirmgerätes derart erfolgen, daß die Höhe der
Bildschirmmitte über dem Boden zwischen 135 – 150 cm beträgt.
d)Der Standfuß muß die Möglichkeit zur Neigung des Bildschirmgerätes besitzen (max. vorwärts: 5°, min. nach
hinten ≥ 5°).
e)Der Standfuß muß die Möglichkeit zur Drehung des Bildschirmgerätes besitzen (max. ±180°). Der maximale
Kraftaufwand dafür muß weniger als 100 N betragen.
f) Der Standfuß muß in der Stellung verharren, in die er manuell bewegt wurde.
g)Der Glanzgrad des Standfusses muß weniger als 20 Glanzeinheiten betragen (seidenmatt).
h)Der Standfuß mit Bildschirmgerät muß bei einer Neigung von bis zu 10° aus der normalen aufrechten Position
kippsicher sein.
Hinweis zur Ergonomie :
Dieser Monitor erfüllt die Anforderungen an die Ergonomie nach EK1-ITB2000 mit dem Videosignal, 1680 ×
1050 (S2233W)/1920 × 1200 (S2243W), Digital Eingang und mindestens 60,0 Hz Bildwiederholfrequenz, non
interlaced. Weiterhin wird aus ergonomischen Gründen empfohlen, die Grundfarbe Blau nicht auf dunklem
Untergrund zu verwenden (schlechte Erkennbarkeit, Augenbelastung bei zu geringem Zeichenkontrast.)
Übermäßiger Schalldruck von Ohrhörern bzw. Kopfhörern kann einen Hörverlust bewirken.
Eine Einstellung des Equalizers auf Maximalwerte erhöht die Ausgangsspannung am Ohrhörer- bzw.
Kopfhörerausgang und damit auch den Schalldruckpegel.
„Maschinenlärminformations-Verordnung 3. GPSGV:
Der höchste Schalldruckpegel beträgt 70 dB(A) oder weniger gemäss EN ISO 7779“
[Begrenzung des maximalen Schalldruckpegels am Ohr]
Bildschirmgeräte: Größte Ausgangsspannung 150 mV
48
Download from Www.Somanuals.com. All Manuals Search And Download.
关于电子信息产品污染控制标识
本标识根据「电子信息产品污染控制管理办法」，适用于在中华人民共和国销售的电子信息产品。
标识中央的数字为环保使用期限的年数。只要您遵守该产品相关的安全及使用注意事项，在自制
造日起算的年限内，不会产生对环境污染或人体及财产的影响。上述标识粘贴在机器背面。
•
有毒有害物质或元素的名称及含量
有毒有害物质或元素
六价铬
（Pb） （Hg） （Cd） （Cr（VI）） （PBB）
部件名称
铅
汞
镉
多溴联苯 多溴二苯醚
（PBDE）
印刷电路板
机箱
×
○
×
×
○
○
×
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
液晶显示器
其他
○：表示该有毒有害物质在该部件所有均质材料中的含量均在SJ/T 11363-2006规定的限量要求以下。
表示该有毒有害物质至少在该部件的某一均质材料中的含量超出SJ/T 11363-2006规定的限量要求。(企业可
在此处,根据实际情況对上表中打“×” 的技术原因进行进一步说明)
×：
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|