User’s Manual
Monochrome LCD Monitor
It shall be assured that the final system is in compliance
to IEC60601-1-1 requirements.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
TABLE OF CONTENTS
PRECAUTIONS...................................................................................4
1. INTRODUCTION .....................................................................................9
1-1. Features ........................................................................................................9
1-2. Package Contents..........................................................................................9
1-3. Controls & Connectors ..............................................................................10
2. CABLE CONNECTION .........................................................................12
3. ScreenManager....................................................................................15
3-1. How to use the ScreenManager ..................................................................15
3-2. ScreenManager Adjustments and Settings...................................................16
3-3. Useful Functions .........................................................................................17
3-4. Power-save Setup ........................................................................................19
4. MAKING USE OF USB (Universal Serial Bus)...................................20
5. ATTACHING AN ARM ...........................................................................22
6.TROUBLESHOOTING...........................................................................24
7. CLEANING............................................................................................27
8. SPECIFICATIONS.................................................................................28
9. GLOSSARY...........................................................................................31
TABLE OF CONTENTS
3
Download from Www.Somanuals.com. All Manuals Search And Download.
English
PRECAUTIONS
IMPORTANT!
• This product has been adjusted specifically for use in the region to which it was
originally shipped. If operated outside the region to which it was originally shipped,
the product may not perform as stated in the specifications.
• To ensure personal safety and proper maintenance, please read this section and the
caution statements on the unit (refer to the figure below).
[Location of the Caution Statements]
SIGNAL1
OWERINPUT
[Symbols on the unit]
Symbol
Location
This symbol indicates
Side
Main power switch
Press to turn the monitor’s main power off.
Side
Main power switch
Press to turn the monitor’s main power on.
Power button
Front
Control panel
Press to turn the monitor’s power on or off.
Rear
Alternating current
Name Plate
Rear
Alerting electrical hazard
Name Plate
Rear
Caution
Name Plate
Refer to SAFETY SYMBOLS section in this
manual.
4
PRECAUTIONS
Download from Www.Somanuals.com. All Manuals Search And Download.
English
WARNING
If the unit begins to emit smoke, smells like something is burning, or
makes strange noises, disconnect all power connections immediately
and contact your dealer for advice.
Attempting to use a malfunctioning unit may result in fire, electric shock, or
equipment damage.
Do not open the cabinet or modify the unit.
Opening the cabinet or modifying the unit may result in fire, electric shock, or
burn.
Refer all servicing to qualified service personnel.
Do not attempt to service this product yourself as opening or removing covers
may result in fire, electric shock, or equipment damage.
Keep small objects or liquids away from the unit.
Small objects accidentally falling through the ventilation slots into the cabinet
or spillage into the cabinet may result in fire, electric shock, or equipment
damage.
If an object or liquid falls/spills into the cabinet, unplug the unit immediately.
Have the unit checked by a qualified service engineer before using it again.
Place the unit at the strong and stable place.
A unit placed on an inadequate surface may fall and result in injury or
equipment damage.
If the unit falls, disconnect the power immediately and ask your dealer for
advice.
OK
Do not continue using a damaged unit. Using a damaged unit may result in
fire or electric shock.
Set the unit in an appropriate location.
Not doing so may result in fire, electric shock, or equipment damage.
*
*
Do not place outdoors.
Do not place in the transportation system (ship, aircraft, trains, automobiles,
etc.)
*
*
*
*
Do not place in a dusty or humid environment.
Do not place in a location where the steam comes directly on the screen.
Do not place near heat generating devices or a humidifier.
Do not place in an inflammable gas environment.
PRECAUTIONS
5
Download from Www.Somanuals.com. All Manuals Search And Download.
English
WARNING
To avoid danger of suffocation, keep the plastic packing bags away
from babies and children.
Use the enclosed power cord and connect to the standard power outlet
of your country.
Be sure to remain within the rated voltage of the power cord.
Not doing so may result in fire or electric shock.
To disconnect the power cord, grasp the plug firmly and pull.
OK
Tugging on the cord may damage and result in fire or electric shock.
The equipment must be connected to a grounded main outlet.
Not doing so may result in fire or electric shock.
Use the correct voltage.
* The unit is designed for use with a specific voltage only. Connection to
another voltage than specified in this User’s Manual may cause fire, electric
shock, or equipment damage.
* Do not overload your power circuit, as this may result in fire or electric
shock.
Handle the power cord with care.
* Do not place the cord underneath the unit or other heavy objects.
* Do not pull on or tie the cord.
If the power cord becomes damaged, stop using it. Use of a damaged cord may
result in fire or electric shock.
Never touch the plug and power cord if it begins to thunder.
Touching them may result in electric shock.
6
PRECAUTIONS
Download from Www.Somanuals.com. All Manuals Search And Download.
English
WARNING
When attaching an arm stand, please refer to the user’s manual of the
arm stand and install the unit securely with the enclosed screws.
Not doing so may cause the unit to become unattached, which may result in
injury or equipment damage. When the unit is dropped, please ask your dealer
for advice. Do not continue using a damaged unit. Using a damaged unit may
result in fire or electric shock. When reattaching the tilt stand, please use the
same screws and tighten them securely.
Do not touch a damaged LCD panel directly with bare hands.
The liquid crystal that may leak from the panel is poisonous if it enters the
eyes or mouth.
If any part of the skin or body comes in direct contact with the panel, please
wash thoroughly. If some physical symptoms result, please consult your
doctor.
Follow local regulation or laws for safe disposal.
The backlight of the LCD panel contains mercury.
CAUTION
Handle with care when carrying the unit.
Disconnect the power cord and signal cables and remove the optional unit.
Moving the unit with the cord or the option attached is dangerous. It may
result in injury.
When handling the unit, grip the bottom of the unit firmly with both
hands ensuring the panel faces outward before lifting.
Dropping the unit may result in injury or equipment damage.
OK
Do not block the ventilation slots on the cabinet.
* Do not place any objects on the ventilation slots.
*
Do not install the unit in a closed space.
*
Do not use the unit laid down or upside down.
Blocking the ventilation slots prevents proper airflow and may result in fire,
electric shock, or equipment damage.
PRECAUTIONS
7
Download from Www.Somanuals.com. All Manuals Search And Download.
English
CAUTION
Do not touch the plug with wet hands.
Doing so may result in electric shock.
Use an easily accessible power outlet.
This will ensure that you can disconnect the power quickly in case of a
problem.
Periodically clean the area around the plug.
Dust, water, or oil on the plug may result in fire.
Unplug the unit before cleaning it.
Cleaning the unit while it is plugged into a power outlet may result in electric
shock.
If you plan to leave the unit unused for an extended period, disconnect
the power cord from the wall socket after turning off the power switch
for the safety and the power conservation.
LCD Panel
In order to suppress the luminosity change by long-term use and to maintain
the stable luminosity, please use the monitor with the brightness below 500
cd/m2 (equal to default setting of BRIGHTNESS approximately 70 %).
The screen may have defective pixels. These pixels may appear as slightly light
or dark area on the screen. This is due to the characteristics of the panel itself,
and not the product.
The backlight of the LCD panel has a fixed life span. When the screen becomes
dark or begins to flicker, please contact your dealer.
Do not press on the panel or edge of the frame strongly, as this may result in
damage to the screen. There will be prints left on the screen if the pressed
image is dark or black. If pressure is repeatedly applied to the screen, it may
deteriorate or damage your LCD panel. Leave the screen white to decrease the
prints.
Do not scratch or press on the panel with any sharp objects, such as a pencil or
pen as this may result in damage to the panel. Do not attempt to brush with
tissues as this may scratch the panel.
8
PRECAUTIONS
Download from Www.Somanuals.com. All Manuals Search And Download.
English
1. INTRODUCTION
Thank you very much for choosing an EIZO Monochrome Monitor.
1-1. Features
• DVI (p.31) Digital input (TMDS (p.31)) compliant
• [Resolution] 2M pixels (1600 dots × 1200 lines)
[Horizontal scanning frequency] 75 kHz
[Vertical scanning frequency] 60 Hz
• USB (Universal Serial Bus) hub supported (p.20)
• The height adjustable stand incorporated
• Ultra slim bezel incorporated
• Power saving function (p.18) (DVI-DMPM(p.31))
NOTE
• Regarding the scanning resolution, the G22-BL/G22-CL supports only the exclusive
timing.
1-2. Package Contents
Please contact your local dealer for assistance if any of the listed items are missing or
damaged.
• LCD Monitor *1
• Power Cord
• Signal Cable (FD-C39)
• EIZO USB Cable (MD-C93)
• User’s Manual
• LIMITED WARRANTY
*1
The orientation of display is landscape position at the default setting. For the
portrait display, pivot the panel in the counter-clockwise direction 90° before
installing the monitor.
NOTE
• Please retain the packing materials for future transference.
1. INTRODUCTION
9
Download from Www.Somanuals.com. All Manuals Search And Download.
English
1-3. Controls & Connectors
Front
(1)
(2)
ENTER
Control Panel
(6)
(3)
(4)
(5)
(1) ScreenManager®
(2)
Main Power Switch
Enter Button
Control Buttons (Left, Down, Up, Right) *1
(3) ENTER
(4)
(5)
(6)
Power Button
Power Indicator *2
Green
Operation
Orange
Power saving
Flashing orange (2 times for each)
Flashing orange slowly
Off
Power save mode
Power is off (Main power is on)
Power off
*1
*2
These buttons are changed to Up, Left, Right, Down in case of selecting
“Landscape” for <Orientation> of ScreenManager <Others> (p.16).
Green lighting when the screen is displayed (Operation mode) can be changed to
non-light, see page 16.
Regarding the power indicator for the off timer, see page 17.
10 1. INTRODUCTION
Download from Www.Somanuals.com. All Manuals Search And Download.
English
Rear
(9)
(10)
(11)
(7)
(8)
(12)
Side
(7) Height Adjustable Stand (Detachable) * 3
(8)
Security Lock Slot *4
(9)
USB Port (1 Upstream)
USB Port (2 Downstream)
(10)
(11)
(12)
DVI-D Input Connector
Power Connector
*3
The LCD monitor has the capability of the Portrait/Landscape display. (The panel
pivots in the clockwise direction 90°.) The LCD monitor can be used with an
optional arm stand by removing the stand (p.22).
*4
Allows for connection of a security cable. This lock supports Kensington’s
MicroSaver security system. For further information, please consult’
Kensington Technology Group
2855 Campus Drive, San Mateo, CA 94403 USA
Tel.: 800-650-4242, x3348, Intl: 650-572-2700, x3348, Fax: 650-572-9675
1. INTRODUCTION 11
Download from Www.Somanuals.com. All Manuals Search And Download.
English
2. CABLE CONNECTION
NOTE
• Be sure that the power switches of both the PC and the monitor are OFF.
• Please refer to the manual of the PC also to connect the monitor.
1. Pivot the panel in the counter-clockwise to fix in portrait position.
2. Plug the signal cable into the connector at the rear of the monitor
and the other end of the cable into the video connector on the PC.
After connecting, secure the connection with the screw-in fasteners.
90°
SGINAL1
Signal Cable
FD-C39
OEWRINPUT
Power Cord
Connector
Signal Cable
PC
Signal Cable (FD-C39 enclosed) Video Output Connector / Exclusive graphics board
DVI
3. Plug the power cord into the power connector on the rear of the
monitor.
12 2. CABLE CONNECTION
Download from Www.Somanuals.com. All Manuals Search And Download.
English
4. Lead the power cord and signal cable into the cable holder at rear of
the monitor.
NOTE
• When housing the cables into the cable holder, lead them to the cable entrance
side and pinch the projection to open the cable entrance.
• The cables are recommended to lead with slight sag for the smooth motion of
the stand.
Projection
Cable Entrance
Cable Holder
5. Plug the other end of the power cord into a power outlet.
WARNING
Use the enclosed power cord and connect to the standard
power outlet of your country.
Be sure to remain within the rated voltage of the power cord.
Not doing so may result in fire or electric shock.
The equipment must be connected to a grounded main
outlet.
Not doing so may result in fire or electric shock.
2. CABLE CONNECTION 13
Download from Www.Somanuals.com. All Manuals Search And Download.
English
6. Turn on the monitor’s Power Button and then switch on the PC’s
power.
The monitor’s power indicator will light up (green).
If an image does not appear, refer to the “6. TROUBLESHOOTING” (p.24) for
advice.
Whenever finished, turn off the PC and the monitor.
7. Set the kind of graphics card.
“8bit” of “Monochrome” (the 8bit monochrome graphics card) is set as default.
If your computer is equipped with the 10bit monochrome graphics card or the 8bit
color graphics card, follow the procedure below.
(1) Select the <Signal Selection> in the ScreenManager (p.15) <Others> menu.
(2) Set the graphics card equipped the computer.
8. When using the optional calibration kit (p.29), connect the upstream
port of the monitor to the downstream port of the USB compliant
PC with the USB cable.
For further details about the calibration, refer to user’s manual in the calibration
kit.
NOTE
• Adjust brightness of the screen depending on the brightness of your environment.
• Be sure to take adequate rests. A 10-minute rest period each hour is suggested.
14 2. CABLE CONNECTION
Download from Www.Somanuals.com. All Manuals Search And Download.
English
3. ScreenManager
3-1. How to use the ScreenManager
ScreenManager
Main Menu
Control Buttons
Left, Down, Up, Right
Enter Button
1. Entering the ScreenManager
Press the Enter Button once to display the main menu of the ScreenManager.
2. Making Adjustments and Settings
(1) Select the desired sub menu icon using the Control Buttons and press the Enter
Button. The sub menu appears.
(2) Use the Control Buttons to select the desired setting icon and press the Enter
Button. The setting menu appears.
(3) Use the Control Buttons to make all required adjustments and press the Enter
Button to save the settings.
3. Exiting the ScreenManager
(1) To return to the main menu, select the <Return> icon or press the Down Button
twice, followed by the Enter Button.
(2) To exit the ScreenManageru, select the <Exit> icon or press the Down Button
twice, followed by the Enter Button.
NOTE
• Double clicking the Enter Button also exits the ScreenManager menu.
3. ScreenManager 15
Download from Www.Somanuals.com. All Manuals Search And Download.
English
3-2. ScreenManager Adjustments and Settings
The following table shows all the ScreenManager’s adjustment and setting menus.
Main menu
Sub menu
Brightness*1
Reference
Screen
Control the brightness for the entire
screen.
Unlock
Unlock the lock. (p.18)
LUT Setting
Default / Normal *2 / Custom*3
Set the LUT (Look-up table) (p.31)
setting.
PowerManager
Others
DVI DMPM
Off Timer
3-4. Power-save Setup. (p.19)
Set the monitor’s off timer to on or off.
(p.17)
Menu Position
Menu Off Timer
Menu
Settings
Adjust the menu position.
Set the menu displaying time.
Orientation
Change the orientation of the
ScreenManager for monitor’s portrait
position.
Signal Selection
Power Indicator
Set the kind of graphics card.
Make non-light for green lighting when
the screen is displayed.
Reset
Return to the factory default settings.
(p.29)
Information
Language
Information
Review the ScreenManager’s settings,
model name, serial number and usage
time *4.
English/Japanese
Select the ScreenManager’s language.
*1
*2
Directly pressing the Control Buttons also adjusts the brightness.
Set to the “Normal” in case of using the monitor with the characteristic of panel
original.
*3
*4
“Custom” automatically stores the customized data after the calibration is performed.
Due to the inspection on the factory, the usage time may not be “0 hour” at shipping.
16 3. ScreenManager
Download from Www.Somanuals.com. All Manuals Search And Download.
English
3-3. Useful Functions
Adjustment Lock
Use the “Adjustment Lock” function to prevent any accidental changes.
Locked function
• Settings in the ScreenManager.
• Adjustment of brightness by the Control Buttons.
[How to lock]
(1) Switch off the monitor’s power by the power button on the control panel.
(2) Press on the Enter button while switching on the monitor’s power.
[How to unlock]
(1) Switch off the monitor’s power by the power button on the control panel.
(2) Hold down the Enter button once again and turn the power back on.
Off Timer
The off timer function causes the monitor to automatically enter a power off state after
a predetermined amount of time has lapsed. This function was created to reduce
afterimage (p.31) characteristics that are particular to LCD monitors when the monitor
screen is left on for a long period without use.
[Procedure]
(1) Select <Off Timer> in the ScreenManager <Others> menu.
(2) Select “Enable” and press the Right and Left Buttons to adjust the “On Period” (1
to 23 hours).
[Off timer System]
PC
Monitor
Power Indicator
On Period (1H - 23H)
Last 15 min. in “On period”
“On period” expire
Operation
Green
Advance Notice *1
Green Flashing
Power off
Flashing orange slowly
*1
Advance notice (Power Indicator flashing green) will be given 15 minutes before the monitor
automatically enters the “Power Off” mode. To delay entering the “Power Off” mode, press
the Power Button during the advance notice period. The monitor will continue to operate for
an additional 90 minutes.
[Power Resumption Procedure]
Press the Power Button to return to a normal screen.
NOTE
• The off timer function works while the PowerManager is active, but there is no
advance notice before the monitor’s power is switched off.
3. ScreenManager 17
Download from Www.Somanuals.com. All Manuals Search And Download.
English
Unlock Function after Calibration
The calibration is available when using the specified optional calibration kit (p.29).
After the calibration, the functions below are automatically locked.
Locked function
• Brightness adjustment (including the adjustment by Left and
Right Buttons on the control panel)
• LUT Setting
Unlock function is available by using ScreenManager.
[How to unlock]
(1) Select the <Unlock> of <Screen> menu.
(2) Select “Unlock”.
NOTE
• Performing the <Reset> of <Others>, locked functions are also unlocked.
18 3. ScreenManager
Download from Www.Somanuals.com. All Manuals Search And Download.
English
3-4. Power-save Setup
The <PowerManager> menu in the ScreenManager enables to set the power-save setup.
NOTE
• Do your part to conserve energy, turn off the monitor when you are finished using it.
Disconnecting the monitor from the power supply is recommended to save energy
completely.
• Even if the monitor is in a power saving mode, USB compliant devices function
when they are connected to the monitor’s USB (both the upstream and the
downstream ports). Therefore, power consumption of the monitor will change
according to the connected devices even if the monitor is in a power saving mode.
This monitor complies with the DVI DMPM (p.31).
[Procedure]
(1) Set the PC’s power saving settings.
(2) Select “DVI DMPM” in the <PowerManager> menu.
[Power saving system]
PC
Monitor
Power Indicator
Operation
Operation
Green
Power saving
Power saving
Orange
Flashing orange
(2 times for each)
Off mode
Power saving
[Procedure]
Operate the mouse or keyboard to return to a normal screen.
Power on the PC to return a normal screen from the Off mode of the PC.
3. ScreenManager 19
Download from Www.Somanuals.com. All Manuals Search And Download.
English
4. MAKING USE OF USB
(Universal Serial Bus)
This monitor provides a hub which supports the USB standard. When connecting to a
USB compliant PC or another hub, the monitor functions as a hub to which the USB
compliant peripherals can be easily connected.
Required system environment
• PC with build-in USB ports or another USB hub connected to the USB compliant PC
• EIZO USB Cable (MD-C93)
NOTE
• The USB hub function may not work properly depending on the PC or peripherals.
Please consult the manufacturer of each device about the USB support.
• Using the USB Rev. 2.0 compatible PC or peripherals is recommended.
• When the monitor is not on, the peripherals connected to the downstream ports will
not operate.
• Even if the monitor is in a power saving mode, the devices connected to the
monitor’s USB ports (both the upstream and the downstream) will function.
Connecting to the USB HUB
1. Connect the monitor to the PC with the signal cable (p.12) first, then
turn on the PC.
2. Connect the upstream port of the monitor to the downstream port of
the USB compliant PC or another hub by using the USB cable.
To Downstream
Ports of the PC
Upstream Port:
or Another Hub
Connect the USB compliant PC or
another hub using the USB cable.
Upstream Port
After connecting the USB cable, the USB function can be set up automatically.
20 4. MAKING USE OF USB (Universal Serial Bus)
Download from Www.Somanuals.com. All Manuals Search And Download.
English
3. After setting up, the monitor’s USB hub is available for connecting
USB compliant peripherals to the downstream ports of the monitor.
Connecting Examples
Monitor
PC
Mouse
Keyboard
Printer
Downstream Ports:
Printer
Keyboard
Connect the cables from USB
compliant peripherals such as a
mouse, keyboard, etc.
Downstream
Ports
4. MAKING USE OF USB (Universal Serial Bus) 21
Download from Www.Somanuals.com. All Manuals Search And Download.
English
5. ATTACHING AN ARM
The LCD monitor can be used with an arm by removing the tilt stand and attaching the
arm or stand to the LCD monitor.
NOTE
• If you will use the arm or stand of other companies, confirm the followings to the arm
or stand maker before selecting.
- Hole spacing on the arm mounting: 100 mm x 100 mm (VESA compliant)
- Supportable Weight: Total weight of the monitor (without stand) and attaching
equipment such as a cable
- TÜV/GS approved arm or stand
• Please connect cables after attaching an arm stand.
Setup Procedure
1. Hold the center of the stand mounting cover and slide them
rightward or leftward to remove the mounting cover.
Stand mounting cover
2. Lay the LCD monitor down. Do not scratch the panel.
3. Remove the tilt stand by loosening the screws.
(4 pcs of M4 x 10 mm)
22 5. ATTACHING AN ARM
Download from Www.Somanuals.com. All Manuals Search And Download.
English
4. Attach an arm stand to the LCD monitor securely.
Arm-stand
4 Mounting Screws: M4 × 10 (mm)
5. ATTACHING AN ARM 23
Download from Www.Somanuals.com. All Manuals Search And Download.
English
6.TROUBLESHOOTING
If a problem persists even after applying the suggested remedies, contact an EIZO dealer.
• No picture problems →See No.1 - No.2
• Imaging problems →See No.3 - No.7
• Other problems →See No.8 - No.9
• USB problems →See No.10 - No.11
Problems
1. No picture
Points to check with possible solutions
†ꢀCheck that the power cord is correctly connected.
If the problem persists, turn off the monitor power
for a few minutes, then turn it back on and try
again.
• Indicator status: Off
†ꢀCheck the “Brightness” setting.
• Indicator status: Green
• Indicator status: Orange
†ꢀTry pressing a key on the keyboard, or clicking the
mouse. (p.19)
†ꢀTry pressing the Power Button.
†ꢀTry turning the PC on.
• Indicator status: Slowly flashing
Orange
• Indicator status: Flashing Orange
(twice for each)
This message appears when the signal is not inputted
correctly, even if the monitor functions properly.
2. Error message shown below will
remain on the screen for 40
seconds.
†ꢀWhen the image is displayed correctly after a short
time, there is no problem with the monitor. (Some
PCs do not output the signal soon after powering
on.)
†ꢀCheck that the PC is turned ON.
†ꢀCheck that the signal cable is properly connected to
the PC or graphics board.
†ꢀUse the graphics board's utility software to change
the frequency setting. (Refer to the manual of the
graphics board.)
3. Error message shown below will
appears.
• The message appears when the signal
is out of input range. ([Input Range]
Resolution: 1600 x 1200, Frequency:
60 Hz)
24 6. TROUBLESHOOTING
Download from Www.Somanuals.com. All Manuals Search And Download.
English
Problems
Points to check with possible solutions
†ꢀAdjust the <Brightness>. (The backlight of the LCD
monitor has a fixed life span. When the screen
becomes dark or begins to flicker, please contact
your dealer.)
4. The screen is too bright or too
dark.
†ꢀWhen the screen image is changed after displaying
the same image for a long period, an afterimage
may appear. The “Afterimage” can be removed
gradually by changing the displayed image. Use the
“Off Timer” function and avoid keeping the screen
on all the time. (p.17)
5. Afterimages appear.
†ꢀThis is due to the characteristics of the panel itself
6. The screen has defective pixels
(e.g. slightly light or dark).
and not the LCD product.
†ꢀLeaving the screen white may solve the problem.
7. Fingerprints remain on the
screen.
†ꢀAfter the calibration, the functions like brightness
are automatically locked. Please refer to page 18 to
unlock.
8. “Locked!” message appears and
the adjustment controls are not
available when pressing the
Control Buttons.
†ꢀThe adjustment lock is probably on. To unlock:
switch the LCD monitor off. Then, while pressing
the Enter Button, switch the power on. (p.17)
9. The Main menu of
ScreenManager does not
operate.
†ꢀCheck that the USB cable is correctly connected.
10. USB function cannot be setup.
†ꢀCheck that the PC and OS are USB compliant. (For
verification of USB support, consult the
manufacturer of each system.)
†ꢀCheck the PC’s BIOS setting for USB. (For details,
refer to the manual of the PC.)
6. TROUBLESHOOTING 25
Download from Www.Somanuals.com. All Manuals Search And Download.
English
Problems
Points to check with possible solutions
†ꢀCheck that the USB cable is correctly connected.
11. PC is hung up. / The peripherals
connected to the downstream
ports do not operate.
†ꢀCheck the downstream ports by connecting the
peripherals to other downstream ports. If the
problem is solved by doing this, contact an EIZO
dealer. (For details, refer to the manual of the PC.)
†ꢀTry executing the following method.
- Restarting the PC
- Connecting the PC and peripherals directly
If the problem is solved by doing this, contact an
EIZO dealer.
26 6. TROUBLESHOOTING
Download from Www.Somanuals.com. All Manuals Search And Download.
English
7. CLEANING
Periodic cleaning is recommended to keep the monitor looking new and to prolong its
operation lifetime.
NOTE
• Never use thinner, benzene, alcohol (ethanol, methanol, or isopropyl alcohol),
abrasive cleaners, or other strong solvents, as these may cause damage to the
cabinet or LCD panel.
Cabinet
To remove stains, wipe the cabinet with a soft, lightly moistened cloth using a mild
detergent. Do not spray wax or cleaner directly into the cabinet.
LCD Panel
• The LCD surface can be cleaned with a soft cloth, such as cotton or lens paper.
• If necessary, stubborn stains can be removed by moistening part of a cloth with water
to enhance its cleaning power.
7. CLEANING 27
Download from Www.Somanuals.com. All Manuals Search And Download.
English
8. SPECIFICATIONS
LCD Panel
50 cm (19.6 inch), TFT Monochrome LCD panel
Anti-Glare Hard Coating 3H, Response Time: approx. 40 ms
Horizontal: 170°, Vertical: 170° (CR≥10)
0.249 mm
Viewing Angle
Dot Pitch
Horizontal Scan Frequency
Vertical Scan Frequency
Resolution
75 kHz (only exclusive timing supported)
60 Hz (only exclusive timing supported)
2M pixels (1600 dots × 1200 lines)
162 MHz
Dot Clock
Gray Scale
1024 steps of 3061 steps
Display Area
398.4 mm (H) × 298.8 mm (V) (15.7” (H) × 11.8” (V))
(Viewable image size: 498 mm (19.6”))
Power Supply
100-120/200-240 VAC ±10%, 50/60 Hz, 0.9-0.7/0.5-0.4 A
Power Consumption
Min.: 65 W, Max.: 85 W (With USB hub)
Power Saving Mode: Less than 6 W (When the USB hub are not
connected.)
Input Connector
DVI-D × 1
Input Signal
Dimensions
TMDS (Single Link)
337 mm (W) × 493 ∼ 575 mm (H) × 208.5 mm (D)
(13.3” (W) × 19.4” ∼ 22.6” (H) × 8.2” (D))
Dimensions (without stand)
337 mm (W) × 441 mm (H) × 78.5 mm (D)
(13.3” (W) × 17.4” (H) × 3.09” (D))
Weight
8.3 kg (18.3 lbs.)
5.3 kg (11.7 lbs.)
Weight (without stand)
Environment Conditions
Temperature
Operating: 0 °C ∼ 35 °C (32 °F ∼ 95 °F)
Storage: -20 °C ∼ 60 °C (-4 °F ∼ 140 °F)
Humidity 30 % to 80 % R.H. Non-condensing
Pressure 860 to 1,060 hPa
USB Standard
Rev. 2.0 complied self-powered hub
Communication Speed
Downstream Power Supply
USB ports
480 Mbps (high), 12 Mbps (full), 1.5 Mbps (low)
500 mA for each (Max.)
Upstream port × 1, Downstream port × 2
Certifications and Standards TÜV Rheinland /GM, CB, NRTL/C-TÜV, CE (93/42/EEC), FCC-A
Classification of Equipment
Type of protection against electric shock: Class I
EMC class: EN60601-1-2 2001: Group1 Class A
Classification of medical device (MDD 93/42/EEC): Class I
28 8. SPECIFICATIONS
Download from Www.Somanuals.com. All Manuals Search And Download.
English
Dimensions
mm (inches)
337(13.3)
300.8(11.8)
3(0.12)
3(0.12)
78.5(3.09)
55(2.17)
168(6.6)
R
O
TAT
I
O
N
27(1.06)
325.5(12.8)
208.5(8.2)
FRONT
SIDE
TOP
Default settings
PowerManager
Off Timer
DVI DMPM
Disable
Menu Position
Menu Off Timer
Orientation
Center
45 seconds
Portrait
Signal Selection
Language
Monochrome 8bit
English
Optional
Calibration Kit
EIZO RadiCS GX2
8. SPECIFICATIONS 29
Download from Www.Somanuals.com. All Manuals Search And Download.
English
Pin Assignment
DVI-D Connector
Pin
No.
Signal
Pin
No.
Signal
Pin
No.
Signal
3
1
9
17
2
4
12
20
6
7
8
5
13
21
10 11
19
14 15 16
24
22 23
18
1
2
3
TMDS Data2-
9
TMDS Data1- 17
TMDS Data0-
TMDS Data0+
TMDS Data2+ 10 TMDS Data1+ 18
TMDS Data2/4 11 TMDS Data1/3 19
TMDS Data0/5
Shield
Shield
Shield
4
5
6
NC*
12
13
14
NC
20
21
NC
NC
NC
NC
DDC Clock
(SCL)
+5V Power
22 TMDS Clock shield
7
8
DDC Data (SDA) 15 Ground (For +5V) 23
TMDS Clock+
TMDS Clock-
Analog Vertical 16 Hot Plug Detect 24
Sync
(*NC: No Connection)
USB Ports
No.
Signal
Signal
Upstream
Downstream
Series A
1
2
3
4
VCC
- Data
+ Data
Ground
Cable power
Serial data
Serial data
Cable Ground
Series B
30 8. SPECIFICATIONS
Download from Www.Somanuals.com. All Manuals Search And Download.
English
9. GLOSSARY
Afterimage
The Afterimage is particular to LCD monitors when the monitor screen is left on for a
long period without use. The “Afterimage” can be removed gradually by changing
the displayed image.
DVI
(Digital Visual Interface)
A digital flat panel interface. DVI can transmit digital data from the PC directly
without loss with the signal transition method “TMDS”.
There are two kinds of DVI connectors. One is DVI-D connector for digital signal
input only. The other is DVI-I connector for both digital and analog signal inputs.
DVI DMPM
(DVI Digital Monitor Power Management)
The Power management system for the digital interface. The “Monitor ON” status
(operation mode) and the “Active Off” status (power-saving mode) are indispensable
for the DVI-DMPM as the monitor’s power mode.
LUT
(Look-up table)
Look-up table is the compensation data, to which the monitor refers, when the
monitor outputs the input data from a graphics board. In this model, the “Default*”
adjusted beforehand referring to look-up table at a factory or “Normal”, which is in
the state of the characteristic of panel original, (i.e. not adjusted) can be available.
“Custom” automatically stores the customized data after the calibration is performed.
*“Default” is adjusted with the 500cd/ms brightness to DICOM grayscale standard.
Resolution
The LCD panel consists of a fixed number of pixel elements which are illuminated to
form the screen image. The EIZO G22-BL/G22-CL display panel consists of 1600
horizontal pixels and 1200 vertical pixels. At a resolution of 1600 × 1200, all pixels
are displayed as a full screen.
TMDS
(Transition Minimized Differential Signaling)
A signal transition method for the digital interface.
9. GLOSSARY 31
Download from Www.Somanuals.com. All Manuals Search And Download.
For U.S.A, Canada, etc. (rated 100-120 Vac) Only
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will required to correct the interference at his own expense.
Changes or modifications not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
Note
Use the attached specified cable below or EIZO signal cable with this monitor so as to keep interference
within the limits of a Class A digital device.
- AC Cord
- Shielded Signal Cable (enclosed)
Canadian Notice
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de le classe A est comforme à la norme NMB-003 du Canada.
For Europe, etc. (rated 200-240 Vac) Only
Warning
This is a Class A product. In a domestic environment this product may cause radio interference in which
case the user may be required to take adequate measures.
Warnung
Bey dem gerät handelt es sich um ein Klasse-A-Produkt. Bei Betrieb des Geräts in Wohnumgebungen ist
gegebenenfalls durch entsprechende Maßnahmen dafür zu sorgen, dass eine Störung des Radio- und
Fernsehempfangs vermieden wird.
Avertissement
Cet appareil est de classe A. Il est susceptible de créer des interférences radio dans un environnement
domestique, dans ce cas l’utilisateur devra prendre les mesures appropriées.
Recycle Auskunft
Die Rücknahme dieses Produktes nach Nutzungsende übernimmt EIZO in Deutschland zusammen mit dem
Partner MIREC GmbH & Co. KG. Dort werden die Geräte in ihre Bestandteile zerlegt, die dann der
Wiederverwertung zugeführt werden. Um einen Abholtermin zu vereinbaren und die aktuellen Kosten zu
erfahren, benutzen Sie bitte folgende Rufnummer: 02153-73 35 00. Weitere Informationen finden Sie auch
Recycling Information for customers in Switzerland:
All recycling information is placed in the SWICO’s website.
Recycling-Information für Kunden in der Schweiz:
Alle Informationen zum Thema Recycling finden Sie auf der Homepage des Brancheverbandes SWICO.
Renseignements de recyclage pour les clients en Suisse:
Vous trouvez tous les renseignements pour le sujet de recyclage sur la page WEB de I’UNION DE BRAN
CHE SWICO.
Recycling Information for customers in USA:
All recycling information is placed in the EIZO Nanao Technologies, Inc’s website.
Återvinnings information för kunder i Sverige:
All information om återvinning finns på Eizo Europe AB:s hemsida:
www.eizo.se
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|