HP-5102
User Manual
01-2013 / v1.0
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
2.3 Fast Ethernet Port................................................................................................................................6
3.1 Win 8....................................................................................................................................................7
3.2 Win XP/Vista / 7.................................................................................................................................15
Chapter 4: Using the Utility Software..............................................................................................................21
Chapter 6: Troubleshooting.............................................................................................................................27
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1: Introduction
1.1 Product Features
Easy plug-n-play setup and 128-bit AES security
Max. powerline speed up to 500Mbps
Backward compatible with 200Mbps powerline adapters
Features energy saving mode to reduce power consumption
Utilizes existing electrical wires to transmit network data
Powerline transmission range up to 300 meters
1.2 Application
High-definition (HD) and standard-definition (SD) video distribution
Broadband Internet sharing
Internet Protocol Television (IPTV) and Voice over Internet Protocol (VoIP)
applications
3
Download from Www.Somanuals.com. All Manuals Search And Download.
1.3 Compatibility
500Mbps powerline devices (HomePlug AV standard) are incompatible and cannot be
used with 14Mbps and 85Mbps powerline devices (HomePlug 1.0 and 1.1 standards).
1.4 System Requirements
Operating System
CPU
RAM
Utility supports Windows XP/Vista/7/8
Intel Pentium III 1.0GHz (or above)
256MB (or above)
Free Disk Space
Network Interface
100MB (or above)
Ethernet port (100Mbps or above) and an Ethernet cable
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Interfaces
2.1 LEDs
LED
Status
Green
Blinking
Off
Description
LAN port connected
LAN activity (transferring data)
LAN port not connected
LAN
The green indicator turns on and the red
indicator turns blinks slowly when the device is
detecting a powerline link.
The green indicator turns on and the red
indicator turns blinks quickly to indicate data is
being transferred over the powerline link.
Green/Red
PLC
Off
Green
Off
No other PLC device detected
Powered on
Powered off
PWR
2.2 Button
Interface
Description
This is a Fast Ethernet port for connecting to a
computer or other devices with a network port.
Creates an encrypted powerline network group
automatically (press the button for less than 3 seconds).
Ethernet Port
Group/Reset
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Leaves an encrypted powerline network group
(press the button for 5~8 seconds).
Restores the powerline adapter to factory defaults
(press the button for 10~15 seconds).
2.3 Fast Ethernet Port
You can connect the powerline adapter to a router, a computer, or any network device
via this Fast Ethernet port.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3:Utility Software Installation
3.1 Win 8
Step 1 Before installing the utility software, make sure that no other powerline utility is
installed on your computer. If any other utility software is installed, uninstall it and
reboot the computer.
Step 2 Insert the CD into your CD-ROM drive. When the following EZmax Wizard appears,
select your model.
Step 3 Then click “Setup Utility”.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 4 Click right button on WinPCap4.1.2 then click “Properties”.
Step 5 Click Compatibility tab and check “Run this program in compatibility mode for:",
then select Windows 7, then click “Apply”.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 6 Then click “WinPcap_4_1_2”. The wizard will guide you through the setup process.
Step 7 When the following WinPcap Compatibility Assistant appears, select Run the
program without getting help.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 8 After the installation is complete, click “Finish”.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 9 Click the “Edimax PowerLine Utility”, the “PLC 500Mbps Utility” appears, click
“Next” to continue.
Step 10 Select where you want to install the utility software, and then click “Next”.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 11 After the installation is complete, click “Close”.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 12 An icon will appear on your desktop. Click the icon to open the utility software.
Note: You can manage all the connected powerline adapters with the utility
software. However, installing the utility software is optional.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
3.2 Win XP/Vista / 7
Step 1 Before installing the utility software, make sure that no other powerline utility is
installed on your computer. If any other utility software is installed, uninstall it and
reboot the computer.
Step 2 Insert the CD into your CD-ROM drive. When the following EZmax Wizard appears,
select your model.
Step 3 Then click “Setup Utility”.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 4 If you have not installed WinPcap version 4.1.2 (or higher) on your computer
before. The wizard will guide you through the setup process.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 5 When the “Edimax PowerLine Utility” setup wizard appears, click “Next” to
continue.
Step 6 In the “License Agreement” screen, please select “I Agree” and then click “Next” to
continue.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 7 Select where you want to install the utility software, and then click “Next”.
Step 8 If you confirm to install the utility, click “Next”.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 9 After the installation is complete, click “Close”.
Step 10 An icon will appear on your desktop. Click the icon to open the utility software.
Note: You can manage all the connected powerline adapters with the utility
software. However, installing the utility software is optional.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Using the Utility Software
4.1 Main Tab
The “Main” tab provides a list of powerline adapters connected to the network. The
upper panel displays local powerline adapters. The lower panel displays remote powerline
adapters in the network.
Set Name
Enter Password
Select a device and click “Set Name” to rename the device.
By default, this column is blank. Select a device and click
“Enter Password” to set up a password for the device.
Click “Scan” and the utility software will perform an
immediate scan of other remote powerline adapters. By
default, the utility automatically scans every few seconds.
Scan
21
Download from Www.Somanuals.com. All Manuals Search And Download.
4.2 Diagnostics Tab
The “Diagnostics” tab displays the system information and history of all remote
devices.
The upper panel displays technical data concerning the software and hardware on the
host computer and the lower panel displays the history of all remote devices.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5: Group Button
This section demonstrates how to add or remove devices from a HomePlug AV network
with the “Group” button.
5.1 Forming a HomePlug AV Logical Network
When two devices with different group keys are connected to the same powerline and
you want them to form a logical network, follow the following procedures:
Step 1 Press and hold the “Group” button on adapter A for less than 3 seconds. The
Power LED will start to blink.
Step 2 Within 120 seconds after the Power LED starts blinking on adapter A, press the
“Group” button on adapter B for less than 3 seconds.
Step 3 Wait for the connection to be established.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
5.2 Joining a Network
If you want to add a new powerline device to an existing network, follow the following
procedures:
Step 1 Press the “Group” button on an adapter in the existing network (adapter A or B) for
less than 3 seconds. The Power LED will start to blink.
Step 2 Within 120 seconds after the Power LED starts blinking on adapter A or B, press
the “Group” button on the new adapter (adapter C) for at least 3 seconds.
Step 3 Wait for the connection to be established.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
5.3 Leaving a Network & Joining another Network
If you want to remove a powerline device from an existing network and add it to
another network, follow the following procedures:
Step 1 Press the “Group” button on the adapter to be removed (adapter B) for at least 10
seconds.
Step 2 Wait for adapter B to be disconnected with adapter A & C.
Step 3 Press the “Group” button on an adapter in another network (adapter D) for less
than 3 seconds. The Power LED will start to blink.
Step 4 Within 120 seconds after the Power LED starts blinking on adapter D, press the
“Group” button on adapter B for at least 3 seconds.
Step 5 Wait for the connection to be established.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6: Troubleshooting
If your powerline adapters have difficulty communicating with each other, try the
following procedures:
Try power cycling the unit by unplugging it from the electric outlet for 10 seconds and
plugging it in again.
Use a pin to hold the reset button down for 2 seconds on each unit you are trying to
connect. The units will reset and attempt to establish a connection using factory default
settings.
Try plugging the powerline adapter into an adjacent electric outlet.
Powerline adapters work better when plugged directly into an electric outlet. Using a
power strip or surge protector may degrade network performance or completely block
network signals.
This powerline adapter should not be used on GFI protected electric outlets, as some
outlets will filter out the powerline signal.
This powerline adapter should not be used in areas with excessive heat.
Certain florescent or incandescent lights are noise sources that can degrade
performance.
If your building has more than one circuit breaker box, your powerline adapters may not
be able to establish a connection across different circuit breaker boxes. In such cases, try
establishing a connection across different circuit breaker boxes by linking two powerline
adapters together with an Ethernet cable.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio technician for help.
FCC Caution
This device and its antenna must not be co-located or operating in conjunction with any other antenna or
transmitter. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Any changes or modifications not expressly approved by
the party responsible for compliance could void the authority to operate equipment.
Federal Communications Commission (FCC) Radiation Exposure Statement
This equipment complies with FCC radiation exposure set forth for an uncontrolled environment. In order to avoid
the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be
less than 2.5cm (1 inch) during normal operation.
Federal Communications Commission (FCC) RF Exposure Requirements
SAR compliance has been established in the laptop computer(s) configurations with PCMCIA slot on the side near the
center, as tested in the application for certification, and can be used in laptop computer(s) with substantially similar
physical dimensions, construction, and electrical and RF characteristics. Use in other devices such as PDAs or lap
pads is not authorized. This transmitter is restricted for use with the specific antenna tested in the application for
certification. The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
R&TTE Compliance Statement
This equipment complies with all the requirements of DIRECTIVE 1999/5/EC OF THE EUROPEAN PARLIAMENT AND
THE COUNCIL of March 9, 1999 on radio equipment and telecommunication terminal equipment and the mutual
recognition of their conformity (R&TTE). The R&TTE Directive repeals and replaces in the directive 98/13/EEC
(Telecommunications Terminal Equipment and Satellite Earth Station Equipment) As of April 8, 2000.
Safety
This equipment is designed with the utmost care for the safety of those who install and use it. However, special
attention must be paid to the dangers of electric shock and static electricity when working with electrical equipment.
All guidelines of this and of the computer manufacture must therefore be allowed at all times to ensure the safe use
of the equipment.
EU Countries Intended for Use
The ETSI version of this device is intended for home and office use in Austria, Belgium, Bulgaria, Cyprus, Czech,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Turkey, and United Kingdom. The ETSI
version of this device is also authorized for use in EFTA member states: Iceland, Liechtenstein, Norway, and
Switzerland.
EU Countries Not Intended for Use
None
28
Download from Www.Somanuals.com. All Manuals Search And Download.
EU Declaration of Conformity
English:
This equipment is in compliance with the essential requirements and other relevant provisions of
Directive 2004/108/EC, 2009/125/EC.
Français:
Cet équipement est conforme aux exigences essentielles et autres dispositions de la directive
2004/108/EC, 2009/125/EC
Čeština:
Toto zařízení je v souladu se základními požadavky a ostatními příslušnými ustanoveními směrnic
2004/108/EC, 2009/125/EC.
Polski:
Urządzenie jest zgodne z ogólnymi wymaganiami oraz szczególnymi warunkami określonymi
Dyrektywą UE 2004/108/EC, 2009/125/EC.
Română:
Русский:
Magyar:
Türkçe:
Acest echipament este în conformitate cu cerinţele esenţiale şi alte prevederi relevante ale
Directivei 2004/108/EC, 2009/125/EC.
Это оборудование соответствует основным требованиям и положениям Директивы
2004/108/EC, 2009/125/EC.
Ez a berendezés megfelel az alapvető követelményeknek és más vonatkozó irányelveknek
(2004/108/EC, 2009/125/EC)
Bu cihaz 2004/108/EC, 2009/125/EC direktifleri zorunlu istekler ve diğer hükümlerle ile
uyumludur.
Українська: Обладнання відповідає вимогам і умовам директиви 2004/108/EC, 2009/125/EC.
Slovenčina: Toto zariadenie spĺňa základné požiadavky a ďalšie príslušné ustanovenia smerníc 2004/108/EC,
2009/125/EC.
Deutsch:
Español:
Dieses Gerät erfüllt die Voraussetzungen gemäß den Richtlinien 2004/108/EC, 2009/125/EC.
El presente equipo cumple los requisitos esenciales de la Directiva 2004/108/EC, 2009/125/EC.
Italiano:
Questo apparecchio è conforme ai requisiti essenziali e alle altre disposizioni applicabili della
Direttiva 2004/108/EC, 2009/125/EC.
Nederlands: Dit apparaat voldoet aan de essentiële eisen en andere van toepassing zijnde bepalingen van
richtlijn 2004/108/EC, 2009/125/EC.
Português: Este equipamento cumpre os requesitos essênciais da Directiva 2004/108/EC, 2009/125/EC.
Norsk:
Dette utstyret er i samsvar med de viktigste kravene og andre relevante regler i Direktiv
2004/108/EC, 2009/125/EC.
Svenska:
Dansk:
Suomi:
Denna utrustning är i överensstämmelse med de väsentliga kraven och övriga relevanta
bestämmelser i direktiv 2004/108/EC, 2009/125/EC.
Dette udstyr er i overensstemmelse med de væ sentligste krav og andre relevante forordninger i
direktiv 2004/108/EC, 2009/125/EC.
Tämä laite täyttää direktiivien 2004/108/EC, 2009/125/EC oleelliset vaatimukset ja muut
asiaankuuluvat määräykset.
WEEE Directive & Product Disposal
At the end of its serviceable life, this product should not be treated as household or general waste. It
should be handed over to the applicable collection point for the recycling of electrical and electronic
equipment, or returned to the supplier for disposal.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Edimax Technology Network Card 80211 b User Manual
Electro Voice Speaker EVA 1151D User Manual
Eureka Vacuum Cleaner 3040 Series User Manual
Fisher Price Baby Accessories R9949 User Manual
Fluke Network Card MedTester 5000C User Manual
Frigidaire Dishwasher 154768601 User Manual
Frigidaire Electric Grill Electric Patio Grill User Manual
GE Clothes Dryer DCCB330EDKC User Manual
GE Indoor Furnishings 10186 User Manual
Genelec Speaker 7050B User Manual