Edelbrock Automobile Parts SOHC Ford V8 User Manual

EFI Victor Jr. 4.6L Intake Manifold  
For 4.6L SOHC Ford V8  
®
Catalog #28385  
INSTALLATION INSTRUCTIONS  
PLEASE study these instructions carefully before beginning this installation. Most installations can be accomplished with common tools and  
procedures. However, you should be familiar with and comfortable working on your vehicle. If you do not feel comfortable performing this installation,  
it is recommended to have the installation completed by a qualified mechanic. If you have any questions, please call our Technical Hotline at:  
1-800-416-8628, 7:00 am - 5:00 pm, Pacific Standard Time, Monday through Friday or e-mail us at [email protected].  
IMPORTANT NOTE: Proper installation is the responsibility of the installer. Improper installation  
will void your warranty and may result in poor performance and engine or vehicle damage.  
DESCRIPTION: This intake manifold is designed to allow the use of aftermarket EFI on a Ford 4.6L Modular Single Overhead Cam engine. This will  
eliminate the use of the OEM fuel injection system and is intended for longblocks that have been installed in early model or custom vehicles. A fuel  
rail kit for this manifold is sold seperately as part #3639.  
KIT CONTENTS:  
1 Victor Jr. Intake Manifold  
1 Fitting; 3/8 NPT to 3/4” hose  
1 Plug; 3/8 NPT  
8 Bolt; M6 x 1.0 x 30mm hex flange head  
INSTALLATION PROCEDURE  
NOTE: This intake manifold is not designed for use in street driven vehicles equipped with the 4.6L engine. It is primarily intended to be used on race  
cars that require air and fuel in excess of what the factory fuel injection system and manifold are capable of supplying. These installation instructions  
do not attempt to cover the steps necessary to convert a vehicle to aftermarket fuel injection, they only cover what is needed to install this intake on  
a properly prepared longblock.  
MANIFOLD INSTALLATION:  
1. Use only the recommended OEM intake gaskets with this manifold.  
2. Fully clean the intake manifold and cylinder head flanges. No  
sealants or adhesives are necessary.  
3. Install the manifold on the block. Lightly coat the manifold bolts with  
30W motor oil then gently thread them into the heads to hold the  
intake in place. Do not apply any torque to the bolts at this time.  
4. Install the themostat and allow it to drop into the machined recess.  
The o-ring supplied with the thermostat should then be pressed in  
and compressed by the thermostat housing.  
5. The manifold bolts (including the thermostat housing bolts) can now  
be tightened according to the torque sequence (See Figure 1).  
Figure 1 - Torque Sequence  
Torque manifold bolts to 15-20 ft/lbs.  
®
Edelbrock Corporation • 2700 California St. • Torrance, CA 90503  
Tech-Line: 1-800-416-8628 • E-Mail: [email protected]  
Catalog #28385  
Rev. 7/08 - AJ/mc  
©2008 Edelbrock Corporation  
Brochure #63-28385  
Page 1  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Exmark Lawn Mower 4500 528 User Manual
Festool Sander DS 400 EQ User Manual
First Alert Home Security System 3035DEF User Manual
GBC Binding Machine 250T User Manual
GE Flat Panel Television JBP70SK User Manual
GE Microwave Oven 164 D2588P188 User Manual
GE Monogram Refrigerator ZDBI240 User Manual
GE PDAs Smartphones eKEY User Manual
GE Pressure Washer WNSB8060 User Manual
Gianni Industries Door 10010 Series User Manual