POLE PRUNER SAFETY MANUAL
DANGER!
Misuse may result in serious or fatal injuries. You must read, under-
stand, and follow these safety instructions and the instructions in your
Operator’s Manual before operating a Power Pruner.
DANGER!
Overhead pruning can result in serious injury or death. Wear head, eye,
face and ear protection that meets ANSI standards to avoid injury from
falling objects or prolonged noise exposure. Place blade cover on
blade when transporting or storing unit.
432-ECHO (3246). Ask how to obtain a FREE Safety Video. Echo’s supplemental Safety
Video provides helpful safety and operating information.
X752000011
12/07
X7522300101
Download from Www.Somanuals.com. All Manuals Search And Download.
SYMBOL MEANINGS AND WARNINGS
Maintain a distance 15m (50 feet) from electrical lines
and electrical sources to avoid electrocution or electrical
shock.
Wear sturdy, protective safety shoes or boots with non-
skid soles. Maintain secure footing and balance.
Read and understand Operator’s Manual to avoid injury.
Wear head, eye, face and ear protection that meets
ANSI standards to avoid injury from falling objects or
prolonged noise exposure.
Hold the Power Pruner™ firmly with both hands with
thumbs and fingers encircling the front and rear handles.
To avoid injury never grasp exposed blades or use
product with one hand.
ON
I
OFF
O
Make sure engine switch is off or unit is unplugged (for
electric) and blades have stopped moving before clearing
jammed material.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
DEFINITION OF TERMS
UNIT - Power head, handles, cutting assembly and pole.
GASOLINEANDELECTRICPOWEREDTERMS
CHOKE LEVER - The engine control attached to the
carburetor that is used to enrich the fuel mixture for cold
starting. Refer to Operator’s Manual for more details
about correct position and use of the choke lever.
GENERALTERMS
ANSI Z87.1 - The established standard for eye protection
devices set forth by the American National Standards
Institute.
BALLISTIC - A special material used in protection devices
designed to reduce the risk of penetration from saw chain
contact.
CLUTCH - The mechanism that transmits the rotation of
the engine’s crankshaft to the cutting assembly.
DIELECTRIC MATERIAL-Amaterial that reduces the
likelihood of shock or electrocution from non-intentional
contact during operation by providing protection against
current flow through the unit to the operator.
BINDING - Closing the cut or shifting the wood, possibly
trapping the saw blade in the cut. Binding includes
pinching. (Also, see PINCH on page 6.)
BRANCH - A secondary shoot or stem arising from one of
the main axes of a tree or woody plant.
GAUGE - A term that is used to describe the size of wire
required when using extension cords with electric units
over specific distances.
BRANCH COLLAR - Trunk tissue that forms around the
base of a branch between the main stem and the branch.
GFCI - Ground Fault Circuit Interrupter. An electrical
circuit breaking device which provides protection against
electrical shock hazards.
BRUSHING OUT - Cutting or otherwise removing under-
growth and brush in the cutting area and along the
planned path of retreat.
IGNITION/STOP SWITCH - An electrical switch which
allows the engine to start and run, and turns the engine
off. Refer to Operator’s Manual to learn and understand
the stop and start procedure.
BUCKING - Generally the standard cross cuts made to
section a log or felled tree. Variations include overbucking
(cutting from top down) and underbucking (from under-
side).
THROTTLE TRIGGER - The device that controls the fuel
and air flow to the gasoline engine, either increasing or
decreasing the engine’s RPM. Refer to the Operator’s
Manual for an illustrated description.
CHAIN TENSIONER - The device which permits precise
adjustment of the saw chain tension.
CHAPS - Specially designed leg protection which can
reduce the risk of injury due to contact with a moving saw
chain.
THROTTLE TRIGGER LOCKOUT LEVER - A lever on the
top of the throttle handle which must be depressed before
the throttle can be activated. When
the operator releases the throttle trigger lockout lever,
the throttle trigger will lock in the idle position.
CHOKE - The engine control used to enrich the fuel
mixture for cold starting.
THROTTLE TRIGGER/STOP SWITCH - An electrical
switch which allows the electric motor to start and run,
and turns the motor off when released. Refer to
Operator’s Manual to learn and understand the stop and
start procedure.
CLEARING - Removing undergrowth and saplings from an
area.
CLOSURE - The process of woundwood covering a cut or
other tree injury.
THROTTLING BACK - Releasing the throttle trigger
to allow a decrease in engine speed (RPM).
CROTCH - The angle formed at the attachment between a
branch and another branch, leader, or trunk.
THROTTLING UP - To increase the engine’s RPM by
depressing the throttle trigger to desired level.
CROWN - The upper portion of a tree from the lowest
branch on the trunk to the top.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
DEFINITION OF TERMS
CROWN CLEANING - The removal of dead, dying,
diseased, crowded, weakly attached branches from the
tree’s crown.
HEARING PROTECTION DEVICES - These are ear-muff or
plug-type devices worn to reduce exposure to harmful
noises while permitting an operator to hear certain sounds.
CROWN REDUCTION - The reduction of the top, sides, or
individual limbs by the means of removal of the leader or
longest portion of a limb.
HOT STICK – Is a non conductive insulated pole used by
electric utilities in moving live downed power lines.
Cleaning material designed with “hot stick” is certified for
cleaning dielectric tools.
CROWN THINNING - The selective removal of branches
to increase light penetration and air movement, and to
reduce weight.
JAMMING - The restriction of the motion of the saw chain
or blade while the engine is running due to an excessive
cutting load or pinching as the cut closes against the
guide bar and saw chain. This can occur when attempting
to cut branches or stems with an excessive feed rate to the
blades.
CUT - The exposed wood area resulting from the removal
of a branch or a portion of it.
CUTTING SHOE - The lower front of the guide bar cover
used as a work stop and/or pivot point when sawing the
blade into the wood.
KICKBACK – This describes two highly dangerous
reactions that can occur. When used alone in this manual,
the term “kickback” refers to rotational kickback. Kickback
can occur if the unshielded guide bar nose touches an
object or the ground.
DECAY - Degradation of woody tissue caused by biologi-
cal organisms.
FACE MASK -Amask to shield the face from flying
objects. Face masks alone do not provide adequate
protection for your eyes. Eye protection goggles or
glasses meeting ANSI Standard Z87.1 must be worn
underneath the face mask. See GOGGLES/GLASSES
(below).
• ROTATIONALKICKBACK - The violent reaction that
can occur when the saw chain at the upper section of
the nose is suddenly stopped or impeded, thereby
dangerously driving the guide bar nose in an upward
arc toward the operator.
•
LINEAR KICKBACK - A push reaction, which can
occur under certain conditions when the guide bar is
buried in a cut and the cut closes, pinching the saw
chain along the top rails of the guide bar and propelling
the saw straight back toward the operator.
FACE SHIELD -Adevice worn in front of the eyes and a
portion of, or all of, the face to supplement eye protection.
A face shield alone does not provide adequate protection
for your eyes. Eye protection goggles or glasses meeting
ANSI Standard Z87.1 or CE Standard must be worn
underneath the face mask. See GOGGLES/GLASSES
(below).
LEADER - A dominant upright stem, usually the main
trunk. There can be several leaders in one tree.
FACILITY - Equipment or structure used to deliver or
provide protection for the delivery of an essential service
such as electricity.
LIMB - Same as branch, but larger and more prominent.
OBSTRUCTING - To hinder, block, close off, or be in the
way of; to hinder or retard a desired effect or shape.
FOLLOW THROUGH - After the saw completes a cut and
is no longer supported by the wood, the bar and chain can
continue on its path and strike the legs, feet or body of the
operator or helper.
PARENT BRANCH OR STEM - The tree trunk; or a large
limb from which lateral branches grow.
PINCH - Specifically the closing-in of the wood which
pinches and stops the saw chain along the top rails of the
guide bar during a cut. This can result in the saw being
propelled straight back toward the operator (called a Linear
Kickback). Pinch can also occur on the lower rails of the
guide bar, resulting in the saw being pulled away from the
operator.
GOGGLES/GLASSES - A device covering the eyes and
sockets, having impact-resistant lenses. Such goggles/
glasses must meet the ANSI Z87.1 or CE Standard. “Z87”
or “CE” is stamped on approved goggles/glasses.
GUIDE BAR - The railed structure that supports and
guides the saw chain.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
DEFINITION OF TERMS
PRECUT OR PRECUTTING - The two-step process to
remove a branch before the finished cut is made so as to
prevent splitting or bark tearing into the parent stem. The
branch is first undercut, then cut from the top before the
final cut.
TREE CUTTING WOUND - The opening that is created
any time the tree’s protective bark covering is penetrated,
cut, or removed. Pruning a live branch creates a wound,
even when the cut is properly made.
UTILITY - An entity that delivers a public service such as
electricity or communication.
PRUNING - Removal of plant parts.
RECIPROCATING CUTTING BLADE -Amoving blade
that alternately changes direction on a linear cutting axis.
UTILITY SPACE - The physical area occupied by the
utility’s facilities and the additional space required to
ensure its operation.
REDUCED-KICKBACK SAWCHAIN -Asaw chain which
has been demonstrated to reduce kickback on some saw
models during ANSI testing.
PUSH AND PULL - When cutting is done along the
bottom rails of the guide bar, the reaction on the saw is a
pull away from the operator. When the top of the guide
bar is used, the reaction pushes the saw toward the
operator. Both are normal reactions that must be con-
trolled by the operator.
SCABBARD - A sheath to cover the saw chain and guide
bar during transport and at other times when the pruner is
not in use.
SKATING - When the guide bar and saw chain or blade
fails to dig in during a cut, the guide bar or blade can begin
hopping or dangerously skidding along the surface of the
branch, possibly resulting in the loss of control of the
pruner. To prevent or reduce skating, properly hold the
pruner with two hands and make sure the saw chain or
blade has established a groove for cutting.
QUALIFIED LINE CLEARANCE TREE TRIMMER - A tree
worker who, through related training and on-the-job
experience is familiar with the techniques in line clearance
and has demonstrated his/her ability in the performance of
the special techniques involved. This qualified person
may or may not be currently employed by a line clearance
contractor.
SPRING POLE - Be alert for spring poles and stay clear of
them during cutting. A spring pole can spring suddenly
when cut, or when the wood holding it down is cut away.
A spring pole can strike you or deflect the saw into your
body
QUALIFIEDTREEWORKER, PERSON, ORPERSONNEL-
Person(s) who, through related training and on-the-job
experience, are familiar with the hazards of pruning,
trimming, repairing, maintaining or removing trees and with
the equipment used in such operations, and have demon-
strated ability in the performance of the special techniques
involved.
STUB - An undesirable short length of a branch remaining
after a break or incorrect pruning cut is made.
REASONS FOR PRUNING - The reasons for tree pruning
may include, but are not limited to, reducing hazards,
maintaining or improving tree health and structure,
improving aesthetics, or satisfying a specific need such as:
removing diseased, dead, dying, decayed, interfering or
obstructing branches; training young trees; and, utility
line clearance. Before pruning, the primary objective
should be clearly defined. That objective should be
accomplished in the manner most beneficial to the health
of the tree.
STRESS FRACTURE - Structural blade or housing damage
resulting from jamming in a cut, using the guide bar/blade
as a lever, dropping the unit, or other abuse.
TERMINAL ROLE - Branch that assumes the dominant
vertical position on the top of a tree.
THINNING - The removal of a branch or branches at the
point of original or the shortening of a branch or branches.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY APPAREL
Always wear eye protection conforming to the ANSI Z87.1 or CE
Standard when operating a pole saw (Z87 or CE is stamped on the eye
protection). Wood chips, dust, snapping branches and other debris can
be tossed by the cutting saw chain into the operator’s facial area. Eye
protection may also offer some protection in the event the chain hits the
operator in the eye area. If conditions warrant that a ventilated face
shield be worn, eye protection must be worn underneath it. Hay fever
(rhinitis) sufferers may purchase disposable masks at hardware or
medical supply stores to help reduce the intake of allergenic particles.
Also, ECHO recommends wearing hearing protection at all times or
hearing loss can occur. You should reduce the risk of hearing damage by
wearing either “headset” type protectors or approved ear plugs. (Note:
Stuffing ears with cotton is not recommended.) All persons who make
part of their living using saws should be tested periodically for hearing
deterioration.
WARNING
DANGER
Operate a pole saw only while wearing eye and/or face protection
that conforms to ANSI Z87.1 or CE Safety Standard (Z87 or CE is
stamped on the eye protection).
Never wear loose clothing, unbuttoned jackets, flared sleeves and
cuffs, scarfs, tie strings, neckties, cords, chains, or jewelry. Also,
secure long hair which could snag or become entangled in the saw
chain, power head or underbrush.
Never operate a pole saw when you are alone. Arrange to have
someone remain within calling distance in case you need help.
During transportation a guide bar or blade cover known as a
scabbard, should always be used.
Failure to follow these warnings can result in serious injury or death.
Always wear a “hard hat” when felling or working under trees. Wear
heavy duty, nonslip gloves for improved grip, and also for protection
against cold and vibration. Safety tip shoes or boots with nonslip soles
should be worn. To reduce the risk of back strain, consider the use of a
lumbar support brace or belt.
Clothing should be of sturdy, protective material. It should be snug-
fitting to resist snagging, but roomy enough for freedom of movement.
Trouser legs should not be flared or cuffed, and should be either tucked
into the boot tops or trimmed short. Safety vests, leg chaps and logger’s
pants of ballistic material are available. It is the operator’s responsibility
to wear such additional protection if conditions warrant.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY PRECAUTIONS
WARNING
DANGER
Do not attempt to start or operate your pole saw until you have
carefully read and completely understand your Operator’s and
Safety Manuals. Locate, understand and follow the warning decals
on your pole saw. Be familiar with the controls and the proper use
of the unit. Know how to shut the unit off. Failure to follow these
warnings can result in serious injury or death.
WARNING
DANGER
Kickback Safety Precaution for Pole Saw Users
KICKBACK may occur when the nose or tip of the guide bar
touches an object, or when the wood closes in and pinches the saw
chain in the cut. Tip contact in some cases may cause a lightning-
fast reverse reaction, kicking the guide bar up and back toward the
operator (this is called a rotational kickback). Pinching the saw chain
along the top of the guide bar may push the guide bar rapidly back
toward the operator (this is called a linear kickback). Either of these
reactions may cause you to lose control of the unit, which could
result in serious injury.
Do not rely exclusively upon the safety devices built into your pole saw.
As a pole saw user, you should take several steps to keep your cutting
jobs free from accident or injury.
•
With a basic understanding of kickback, you can reduce or eliminate
the element of surprise. Sudden surprise contributes to accidents.
Understand that rotational kickback is preventable by keeping an
unshielded guide bar nose from touching an object or the ground.
•
Do not operate a pole saw with one hand! This can result in the pole
saw “skating” or skidding, which can result in personal injury due to
loss of control. Serious injury to the operator, helpers or bystanders
may result from one-handed operation. For proper control, always
use two hands when operating a pole saw.
•
Keep a good firm grip on the pole saw with both hands, with the right
hand on the rear handle and the left hand on the front handle, when
the engine or motor is running. Use a firm grip with thumbs and
fingers encircling the pole saw handles and grips. A firm grip will
help you reduce kickback and maintain control of the pole saw. Don’t
let go.
•
•
Make sure that the area in which you are cutting is free from obstruc-
tions. Do not let the unshielded guide bar nose contact a log, branch,
or any other obstruction while you are operating the unit.
Normally cutting at high engine speeds will reduce the likelihood of
kickback. However, cutting at part-throttle or low engine speeds may
be preferable to control the pole saw in tight situations and may also
reduce the likelihood of kickback.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY PRECAUTIONS
•
•
Follow sharpening and maintenance instructions for the saw chain in
your Operator’s Manual. Do not resharpen saw blades.
Use only replacement guide bars, saw chains or blades specified by
the manufacturer.
•
•
Do not over reach.
Do not operate the unit if you are fatigued, or under the influence of
alcohol, medication or any substance that can affect your vision,
dexterity or judgment. You must be in good physical and mental
health to operate a pole saw safely.
•
Never operate your pole saw unit without its proper guards, shields,
and protective devices in place. Check to make sure before operating.
•
•
Do not operate a unit in disrepair, or with damaged or missing parts.
Use only genuine ECHO replacement parts. Check that the cutting
attachment, guide bar and saw chain are firmly attached and in safe
operating condition.
DEALER?
Call
All maintenance specified in your pole saw Operator’s Manual should
be performed by you or an authorized ECHO servicing dealer. Any
service or repair work that the Operator’s Manual does not address
should be done by an authorized ECHO servicing dealer only. For a
dealer near you dial 1-800-432-ECHO (3246).
1-800-432-ECHO
•
Use caution when handling fuel. Move the pole saw at least 3m (10
feet) from the fueling point before starting the engine.
•
Do not allow other persons to be near the pole saw when you are
starting or cutting with the saw. Keep bystanders and animals 15m
(50 feet) away from the work area. Do not let anyone hold wood for
you to cut.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY PRECAUTIONS
• Keep all parts of your body away from the saw chain or blade when
the engine is running.
• Before you start the engine or motor, make sure the saw chain or blade
is not contacting anything.
• Carry the pole saw with the engine or motor stopped, the guide bar
and saw chain or blade to the front, and keep the hot muffler away
from your body.
• Do not operate a pole saw that is damaged, improperly adjusted, or not
completely and securely assembled. Be sure that the saw chain or
blade stops moving when the throttle control trigger is released.
• Shut off the engine or motor before setting the unit down.
• Use extreme caution when cutting small-size brush and saplings
because slender material may catch the saw chain and be whipped
toward you or pull you off balance.
• When cutting a limb that is under tension, be alert for springback so
that you will not be struck by the limb or saw when the tension in the
wood fibers is released.
• Keep the handles dry, clean, and free of oil or fuel mixture.
• Do not operate a pole saw standing in a tree.
• Fuel your pole saw safely. Handle flammable fuel with care. Use an
approved gasoline container. Do not smoke or bring sparks or flame
near the fuel supply. Use proper fueling procedures recommended in
the pole saw Operator’s Manual. Do not over fill the fuel tank. If
spilling occurs, clean up before you attempt to start the unit. Always
make sure engine fuel cap is securely tightened before operating.
• Use only one ECHO approved extension on your pole saw.
• Do not hit rocks, stones, or other foreign objects with the saw chain or
blade.
• If the cutting attachment strikes an obstruction, stop the engine or
motor immediately and inspect the cutting attachment for damage, do
not contact ground with saw chain or blade.
• When transporting your pole pruner use the appropriate guide bar or
blade scabbard.
1 0
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY PRECAUTIONS
•
•
Do not run the gasoline engine indoors, or where there is poor
ventilation. Engine exhaust contains deadly carbon monoxide
poison.
Keep both feet on the ground. Do not work from off-the ground
positions. Working from ladders is extremely dangerous because
ladders can slip, as well as, limit your control of the pole saw. Work-
ing aloft should be left to professionals.
•
•
Use your saw only to cut wood or wood products. Do not cut solid
metal, sheet metal, plastics or any non-wood materials.
Stay on the uphill side when pruning, limbs may roll down hill
when cut.
•
•
Work only when there is adequate lighting to see clearly.
When there are several workers, they should be stationed where they
will not interfere with one another. During cutting operations, only
one person should be working on a tree.
•
•
•
•
Before cutting, clear the area of materials likely to start brush fires or
interfere with you or the saw. Be sure the path of retreat is clear. It is
wise to plan two exit paths in case one becomes blocked.
Do not go under trees during periods of high wind or heavy precipita-
tion. If a fallen or broken tree creates an emergency, leave removal to
a professional tree removal service.
Any tree with a hollow rotted trunk, thick loose bark, and dead
branches is extremely dangerous to disturb by cutting. Such trees
should be worked on by professionals.
Do not allow anyone to enter a zone of 15m (50 feet) from where you
are working. If the risk of eye injury exists to people outside of 15m
(50 feet), require them to wear ANSI or CE approved eye protection.
•
•
Always disconnect and move the spark plug wire away from the spark
plug before you work on the unit or leave it unattended.
Ensure that the operator can see where the cutting action is occur-
ring. Use the proper tools. If the branch or limb cannot be safely cut
with your pole saw, use other tools such as hand pruners or hand
saws or consult with a professional.
•
•
Be aware of local ordinances which may restrict the use of a pole
pruner product.
Use only certified dielectric cleaning material such as “hot stick” for
cleaning dielectric tools. Refer to your Operator’s Manual for
additional information.
1 1
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY PRECAUTIONS
WARNING
DANGER
The pole saw’s engine can continue to run when the blade is
jammed. Before attempting to release or free the jam, always switch
the engine off, disconnect the spark plug wire from the spark plug.
After assuring the blade and engine have stopped, proceed to clear
the jam. Wear gloves while clearing material from the jammed blades.
Never grasp the sharp, exposed cutting blade of the pole saw. If you
contact the cutting blade, serious personal injury may occur.
OFF
O
•
Do not misuse the blade or the unit. Never use the unit for anything
other than it was intended. Do not use it as a hammer, lever, or
crowbar.
•
•
To avoid burns, always make sure that the muffler side of the engine
is away from your body.
Shut off the pole saw immediately if the unit starts to shake or vibrate
excessively. This could be a sign of danger. A part may be broken or
loose.
•
After shutting off the engine or motor, keep your fingers and body
away from the cutting attachment until all movement has stopped.
Saw chain or blade will coast to a stop after releasing the throttle.
1 2
Download from Www.Somanuals.com. All Manuals Search And Download.
SOME ADDITIONAL SAFETY PRECAUTIONS
PRECAUTIONS IN HOT, HUMID WEATHER - Heavy clothing can
increase an operator’s fatigue. Heat stroke or heat exhaustion is pos-
sible. Under these adverse conditions, you must judge whether wearing
heavy protective clothing or lighter but less protective items bears the
least risk. Or you might wisely choose to delay work until the tempera-
ture drops.
PRECAUTIONSAGAINSTVIBRATIONAND COLD - It is believed that
a condition called Raynaud’s Phenomenon, which affects the fingers of
certain individuals, may be brought about by exposure to cold and
vibration. Accordingly, your ECHO pole saw has a vibration reduction
system designed to reduce the intensity of vibration received through
the handles. Exposure to cold and vibration may cause tingling and
burning followed by loss of color and numbness in the fingers. We
strongly recommend that you take the following precautions because the
minimum exposure which might trigger the ailment is unknown.
•
•
•
•
Keep your body warm, especially the head, neck, feet, ankles, hands
and wrists.
Maintain good blood circulation by performing vigorous arm exer-
cises during frequent work breaks and also by not smoking.
Limit the number of hours of cutting operation. Try to fill a part of
each work day with jobs other than pruning.
If you experience discomfort, redness and swelling of the fingers,
followed by whitening and loss of feeling, consult your physician
before further exposing yourself to cold and vibration.
PRECAUTIONS AGAINST REPETITIVE STRESS INJURIES - It is
believed that overusing the muscles and tendons of the fingers, hands,
arms and shoulders may cause soreness, swelling, numbness, weakness
and extreme pain to the areas just mentioned. Certain repetitive hand
activities may put you at a high risk for developing a repetitive stress
injury (RSI). An extreme RSI condition is Carpal Tunnel Syndrome (CTS),
which can occur when your wrist swells and squeezes a vital nerve that
runs through the area. Some believe that prolonged exposure to vibra-
tion may contribute to CTS. CTS can cause severe pain for months or
even years. To reduce the risk of RSI/CTS, do the following:
•
Avoid using your wrist in a bent, extended or twisted position.
Instead, try to maintain a straight wrist position. Also, when grasp-
ing, use your whole hand, not just the thumb and index finger.
Take periodic breaks to minimize repetition and rest your hands.
Reduce the speed and force in which you do the repetitive movement.
Do exercises to strengthen the hand and arm muscles.
Immediately stop using all power equipment and consult a doctor if
you feel tingling, numbness or pain in the fingers, hands, wrists or
arms. The sooner RSI/CTS is diagnosed, the more likely permanent
nerve and muscle damage can be prevented.
•
•
•
•
EQUIPMENT TO BRING ALONG - When using gasoline powered
engines, fuel supplies should be carried in approved fuel containers.
Bring an extinguisher or shovel in case of a fire. Despite the precautions
which can be taken, operating a pole saw presents some dangers so keep
a first aid kit handy.
1 3
Download from Www.Somanuals.com. All Manuals Search And Download.
FORCES TO CONTROL
This section is about forces which must be controlled to avoid injury
when operating a pole saw. Pros and cons of various safety devices are
included in the discussion. Always remember that your best defenses
are to exercise caution and use the pole saw properly.
Here is an example of a reaction to an action: if you sit on the floor and
push forcefully enough against a wall with your feet, your body will slide
away from the wall. For pole saw operators, when the saw chain forces
its way into the wood from one direction, the reaction tends to move the
pole saw in the opposite direction.
PULL, PUSH and KICKBACK - terms for the direction a reaction takes.
•
PULL - This occurs when you are cutting on top of a log with the
lower portion of the saw chain moving toward you. The pole saw will
be pulled into the wood and away from you.
•
•
PUSH - This is the cutting on the underside of a log with the top of
the bar. It pushes the pole saw toward you.
ROTATIONAL KICKBACK - This happens when the saw chain is
moving downward around the upper nose of the bar. Solid contact in
this situation may dangerously drive the guide bar tip upward in an
arc toward you.
FORCE
REACTION
FORCE
•
LINEAR KICKBACK - Describes a sudden PUSH reaction when the
guide bar is buried in a cut which closes and pinches the saw chain
along the top rails of the guide bar. This propels the pole saw
straight back toward the operator.
REACTION
Rotational kickback is predictable, preventable and controllable. If the
operator is not alert to the possibility of a kickback, it may come as a
complete surprise. The best defense against rotational kickback is
making sure the saw chain contacts nothing solid at the upper nose of
the guide bar. PUSH and PULL forces are controlled by anticipating
which reaction will happen and adjusting your position and stance to
compensate.
ROTATIONALKICKBACK
FORCE OF GRAVITY - When you are operating a pole saw you must
accommodate for gravity. Maintain proper grip and stance. Keep good
footing. Don’t cut while off balance — gravity may work against you.
Never reach too far with the pole saw.
CHAIN MOVING DOWNWARD AT IMPACT
FOLLOW THROUGH - When you’re about to complete a cut, be ready to
throttle back and hold up the pole saw so that the cutting attachment will
not follow through into you or hit the ground after the guide bar or blade
cuts through the branch.
SKATING - This condition occurs when the saw chain or blade does not
dig in properly when starting a cut. In other words, the saw chain or
blade does not get tracked as it attempts to penetrate the wood. The
guide bar or blade can then begin hopping or skidding side-to-side along
the surface. At this point, you do not have full control of the saw, and
the guide bar nose or blade could strike an obstruction and create a
kickback.
If you are holding the saw with one hand and a branch with the other, the
saw could skate laterally into your hand holding the branch. To prevent
or reduce skating, hold the pole saw with two hands and make sure the
saw chain or blade has established a groove for cutting. Throttling down
the saw chain or blade speed may help to get a groove started, but once
the saw chain or blade is grooved, throttle the unit up to complete the
cut.
1 4
Download from Www.Somanuals.com. All Manuals Search And Download.
FORCES TO CONTROL
On guide bar and saw chain configured pole saws, proper saw chain
tension cannot be maintained when and if the:
•
•
•
Drive sprocket is worn.
Guide bar is improperly clamped to the pole saw.
Tension adjuster has not engaged the guide bar, thus allowing the
guide bar to shift.
•
•
Guide Bar rails are in poor condition.
Guide bar and saw chain are improperly lubricated.
WARNING
DANGER
Equipment, including your pole saw, should not be transported in
the same compartment as passengers, and must be secured in some
manner. Cover the saw chain and guide bar or blade with a scabbard
or serious injury may occur.
PROPER GRIP ON THE POLE SAW -Afirm grip is one requirement for
pole saw control. The saw should always be held firmly with both hands
with thumbs and fingers encircling the front and rear handles whenever
the engine or motor is running.
•
•
Wear heavy duty nonslip gloves to improve your grip on the handles.
Grasp the front handle firmly with your left hand. Use the proper grip
with fingers encircling and the thumb on the underside. Thumb
position is the key to a strong grip.
•
Grasp the rear handle in the same manner as the front handle. Use
index finger to work the throttle trigger, and practice operating the
engine stop switch without losing your hold on the unit.
WARNING
DANGER
Always use a wraparound grip. Never use a grip where the thumb
and finger do not encircle the unit handles. If you use an improper
grip, even a slight push or kick of the unit may dislodge your hand
and cause serious injury.
1 5
Download from Www.Somanuals.com. All Manuals Search And Download.
BALANCE AND BODY POSITION FOR CUTTING
Pole saws are designed for light to medium trimming of limbs and
branches up to 20.3 cm (8 in.) in diameter. After starting, pick up the pole
saw and proceed as follows:
•
•
•
Plan cut carefully. Check direction branch will fall.
Do not stand directly beneath branch being cut.
Plan a retreat path from falling branches. Branches may bounce when
striking the ground.
•
•
Stand with your weight on both feet. Adjust your stance so as to be
away from the saw chain or blade and the line the limb will fall.
When ready to cut:
Hold front cutting guide against branch. This will prevent the branch
from whipping. DO NOT use back and forth sawing action.
Look out for the branch immediately behind the one being cut. If the
saw chain hits the rear branch damage to the saw chain may occur (or
kickback).
•
•
•
•
•
Accelerate to full throttle.
Apply cutting pressure.
Ease cutting pressure when nearing end of cut to maintain control.
When pruning a limb 10.2cm (4 inches) in diameter or larger cut as
follows:
1. Under cut 1/4 limb diameter near tree trunk.
2. Finish top cut slightly further out on limb from tree trunk.
3. Flush cut stub at trunk.
Long branches should be removed in several pieces.
At completion of the cut, let go of the throttle trigger, carefully lift the
pole saw clear, and idle the engine before moving away.
DO NOT use Pole Saw for felling or bucking.
•
•
•
WARNING
DANGER
Moving toward the next place to cut before throttling down and
lifting the saw clear of the cut can cock the saw chain or blade
against the sides of the cut. Always throttle down and let the saw
chain or blade come to a stop and lift the saw clear of the wood
before moving away. Failure to do so may result in serious injury.
•
Review your cuts carefully. Sometimes the way the branch is stressed
will endanger you.
WARNING
DANGER
If a branch starts to fall, causing your saw to bind, LEAVE THE SAW
AND GETAWAY FAST! or serious injury may occur.
•
•
Do not let the nose of the guide bar come near any solid object while
the saw chain is rotating. Never let the guide bar dip into the ground.
Keep your body out of the path of a potential kickback. During all
cutting, do not bend toward or otherwise crowd the guide bar or
blade.
•
•
Cut only one piece of wood at a time.
Do not thrust the nose of the guide bar into a pile of branches or
dense brush where you cannot see if the nose is in the clear.
When starting a cut, be ready to control any tendency of the guide
bar to skate as it attempts to penetrate the wood. Kickback could be
a secondary reaction if the guide bar nose or blade skates into an
obstruction.
•
1 6
Download from Www.Somanuals.com. All Manuals Search And Download.
BALANCE AND BODY POSITION FOR CUTTING
•
•
•
•
When completing an elevated cut, be ready to hold up the pole saw
as it cuts into the clear, so it will not follow through.
Limit your cutting to the range within which you can control the pole
saw fully. Don’t reach out because you could lose your balance.
Make limbing and pruning cuts one at a time. Do not try to prune
more than one branch at a time.
Do not prune near power lines.
PINCHING, BINDING, SPLITTING
Wind bends trees. Gravity bends branches that are not flat on the
ground. A branch weakened by a cut over 1/3 the diameter is like two
branches hinged together. The cut may either close or open wider,
depending on how the branch is lying.
When cutting branches, always make the weakening cut from the
direction (opposite the hinge side) which causes the cut to widen. If
made from the wrong side, the cut will close, binding the guide bar and
pinching the saw chain or blade.
If the branch is under heavy stress, prevent splitting by making a shallow
cut (up to 1/3 diameter) on the hinge side first. But, always finish with
the weakening cut in a direction toward the hinge side.
When the branch is supported on both ends and is to be cut in between,
underbuck (cut upward from the bottom side) for the finishing cut.
1 7
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMBING AND BUCKING
When you wish to cut off an unsupported section from the end of a
branch, the weakening or finishing cut should be an overbuck (from top
down). However, you may begin with a shallow underbuck to avoid
splitting and some damage to the tree or limb.
WARNING
DANGER
Do not cut, walk or stand on a limb while cutting. Serious personal
injury may result.
If the saw chain becomes pinched in a bind, SHUT OFF THE ENGINE OR
MOTOR. Free the bind by lifting the limb. Use levers, poles, etc. for
lifting. This avoids back injuries.
When a branch is held off the ground by its limbs, determine which of
these are needed for support. Leave these while you cut off all the other
limbs and branches.
You will lose support of the limbs as sections of the branch are cut. Go
to the high ground side of the branch to buck off limbs. Be sure to have
a retreat path should the limb roll toward you as branches are removed.
Do not use SRS models for bore cutting or serious personal injury
may result.
WARNING
DANGER
OFF
O
WARNING
DANGER
There is danger of kickback during boring. It is not recommended to
bore cut with a pole pruner. Do not use SRS models for bore cutting.
Serious personal injury or death can result from improper bore
cutting.
Avoid windfalls. Windfalls are tangled branches, roots and trees. Clean
these out only by cutting from the perimeter.
1 8
Download from Www.Somanuals.com. All Manuals Search And Download.
WHEN TO CALL A PROFESSIONAL
There are times that the solution to a problem with a mature tree is best
handled by a professional arborist.
When do you call for professional help?
1. When you don’t have the expertise and proper equipment to safely
accomplish the job.
2. When the tree is too large and pruning requires extension equipment
like a bucket truck.
3. When the tree is located near utility lines, buildings or a highway you
should consult a professional.
4. When major storm damage requires judgment on whether and how to
save a tree.
5. If you are not sure when or how to prune.
Be selective about who you hire to care for your trees. Look for a
company that uses certified arborists trained to properly care for trees.
Inquire about the equipment they use. For example, will they use a
bucket truck to reach your high branches or do they use extended-reach
pruning equipment? Do they use safety accessories and safe equipment,
like insulated power equipment for use around high-voltage wires?
Always ask a tree care company for customer references. Take the time
to visit them and look at the job that was done on their trees.
1 9
Download from Www.Somanuals.com. All Manuals Search And Download.
PRUNING: TIMING AND TECHNIQUE
Pruning is vital to the health and beauty of trees. Pruning
controls the size and direction of growth, improves a tree’s
health, diminishes risk of infection and increases the size of
flower and fruit production. Proper pruning also encourages
growth by opening up the tree’s canopy and branch structure.
But first and foremost, proper pruning is important for tree health.
Dead wood that is left on a tree is a food source for fungi and
bacteria that can damage a tree. Such dead and decaying wood
can also open passageways for invasive insects.
TIMING
On most trees, the ideal time to prune is during the winter months
when sap flow has either stopped entirely in northern regions or
slowed considerably in southern regions. Early spring is also a
good time to prune, as long as trees have six weeks of healing
time before the first signs of growth.
There are exceptions. Trees and shrubs that flower in the early
spring, such as lilacs and redbuds, are best pruned within the
two-week period following blossom drop. Many varieties of
needled evergreens are best pruned in the spring as well, just as
new growth emerges.
Pruning should be matched to the needs of each tree, in tech-
nique and timing. Some trees require frequent pruning while
others require very little.
PRUNINGTECHNIQUES
Before pruning any tree, determine the objective. There are
several reasons to prune a tree. As a general rule, prune a tree
first for safety reasons, then for health, and then for aesthetics.
No matter what the reason is for pruning, as a general rule of
thumb, remove no more than a quarter of the tree’s foliage.
Pruning techniques vary depending on the size and location of
the branch.
When a small branch is pruned away, the cut should be made
close to where it emerges from a larger branch. This way, the
plant’s natural growth pattern is encouraged. Cuts on branches
or stems should be made at a moderate angle; too great an angle
exposes a large, oblong wound that takes longer to heal and is
more susceptible to infection.
When trimming side branches, the final pruning cuts should be
made at the outside edge of the branch collar (the slightly
swollen area where the branch attaches to the trunk). On larger,
heavy branches pruning cuts may have to be made several
inches from where the branch emerges, to avoid any tearing of
the bark when the branch falls.
2 0
Download from Www.Somanuals.com. All Manuals Search And Download.
PRUNING: TIMING AND TECHNIQUE
•
WOUND DRESSINGS - Wound dressings have been shown to
interfere with the natural development of callus tissues that eventu-
ally close the pruning wound. In some cases, wound dressings can
even harbor disease organisms much like what occurs when a Band-
Aid is left on a skin cut too long. It is far more important to make the
cut smooth, outside of the collar and allow the wound to dry.
If a wound dressing is desired for aesthetic purposes, use a very thin
coat, just enough to darken the wound area. The best are the aerosol
sprays of water-emulsified asphalt sold in garden centers. Do not use
oil-based paints, thick tars or other materials containing petroleum
solvents.
•
MAINTAIN TREE HEALTH - The key to good wound closure
following pruning is to maintain a healthy tree through proper
watering, fertilizer application and pest control. Trees under stress
from drought, over-watering, pest attack, lawn mower and other
mechanical damage, and poor nutrition cannot successfully fight off
invasion of disease.
For larger branches, a three-step approach is recommended to avoid
tearing or ripping the tree’s bark.
1. The first cut should be a shallow notch, made on the underside of
the branch several inches from the branch collar.
2. The second cut, which goes entirely through the branch, is made
just outside the first cut.
3. The remaining stub is then cut just outside the branch collar.
Always prune branches to the point of origin. Remove small twigs where
they emerge from small branches and remove large branches at the
juncture with a larger branch or at the trunk.
Be sure to remove all dead or damaged branches first, followed by
branches that interfere with each other or those that form weak angles.
Retain the strongest, best placed branches; remove the weaker ones.
SHRUBS
Many shrubs have growth patterns similar to trees, but on a smaller
scale. They should be pruned like trees, with these considerations:
A. Prime pruning periods for deciduous shrubs depend on the
purposes for which the shrubs are grown. For example, shrubs
whose foliage is the greatest attribute can be pruned anytime
during the winter to early spring. Shrubs whose spring flowers are
their best feature are best pruned immediately after the blooming
period. And shrubs grown primarily for their summer blossoms
can be pruned during the winter.
B. Up to one-third of a deciduous shrub’s growth can be removed at
any one time. By selectively removing the oldest, heaviest
branches at ground level, you automatically reduce its height.
Some of the most sturdy hedge plants can be cut back further, to
within six or eight inches of the ground during late winter. These
plants will shoot up new growth in the spring, thickening a young
hedge or rejuvenating an old one.
2 1
Download from Www.Somanuals.com. All Manuals Search And Download.
PRUNING: TIMING AND TECHNIQUE
C. With most needled evergreens, pruning is confined to
trimming back a portion of new growth to control height or
spread, or to even the shape. Pine growth tips (commonly
called candles) can be cut back from one-third to three-
quarters prior to the time the needles of the candles unfold.
The growth tips of spruce and fir can be trimmed back by as
much as three-quarters while the shoots are still tender and
flexible.
TECHNIQUE
When trimming shrubs and hedges, there are two approaches. One
involves pruning away old wood to induce new shoots and growth;
the other involves clipping or trimming the shrub to reduce its total
height. Small-leaf, close-textured shrubs respond well to repeated
clipping and make the best formal hedges. Larger-leaf, open shrubs
are better suited for pruning and not trimming with a hedge clipper.
When operating hedge shears or clippers, hold the cutting blades
parallel to the surface you’re trimming, and cut back to the point
where you’ve previously sheared. By starting low and working your
way up, it makes it easier to trim the top part of the hedge. Tools like
ECHO’S new shaft hedge trimmers help to extend reach while the
articulating hedge trimmer makes sculpting a breeze and facilitates
reaching across the top of taller hedges while still maintaining a
parallel cut.
When the trimming project is done, remove the bulk of the clippings,
but don’t worry about the few that remain on top of the hedge or
that fall within its borders.
In a few days they will shrivel up and die.
PRUNING DO’S AND DON’TS
Two common practices are particularly harmful to trees and should
be avoided at all costs.
•
One is referred to as topping, the indiscriminate heading of large
upright branches to reduce the height of a tree.
•
The other is called tipping, the cutting away of lateral branches
to reduce crown width.
Both practices not only leave behind an unsightly tree, they also
inflict damage that will kill the remainder of the cut branch and quite
possibly cause additional tree stress.
Still, one of the most common ways trees are injured is to simply not
follow recommended pruning practices that needlessly rip away bark
or otherwise leave trees susceptible to insects, disease and decay.
Also, latest research has shown that painting tree wounds is not
necessary. Trees develop their own barriers to seal off damaged or
freshly pruned tissues.
Routine pruning is vital to the health of all trees and shrubs. When
done properly, it will work to maintain health, vigor and beauty and
help ensure these landscape elements deliver years of trouble-free
enjoyment to property owners.
2 2
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
2 3
Download from Www.Somanuals.com. All Manuals Search And Download.
ECHO INCORPORATED
400 OAKWOOD ROAD
LAKE ZURICH, IL 60047
PHONE: (847) 540-8400
Printed in USA
NOTICE:
ECHO, INCORPORATED reserves the right to make changes in this safety manual or the models
without advanced notice.
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Everpure Water System EV9104 50BB User Manual
Extron electronic Network Card SCS 300 User Manual
Fisher Price Automobile L7978 User Manual
Foundations Baby Furniture 100 EVBP User Manual
Franke Consumer Products Ventilation Hood FCR 708 H TC User Manual
Fujitsu Server BX900 S1 User Manual
Fundex Games Games Old Maid User Manual
Furuno Radar Detector FMD 8010 User Manual
GE Washer WBVH5200 User Manual
Gladiator Garageworks Freezer 2253210A User Manual