Echo Blower ES 255 User Manual

SHRED'N'VAC®  
Operator's Manual  
MODEL  
ES-255  
wARNiNg  
Read rules for safe operation and instructions carefully. ECHO provides this  
Operator's Manual, which must be read and understood for proper and safe opera-  
tion.  
X750011944  
11/09  
X7501180704  
Download from Www.Somanuals.com. All Manuals Search And Download.  
®
Sh r e d 'N'Va c  
Op e r a t O r 'S Ma N u a l  
3
sa f e T y  
m a n u a l s a f e T y s y m b o l s a n d Im p o r T a n T In f o r m a T Io n  
Throughout this manual and on the product itself, you will find safety alerts and helpful, informational messages pre-  
ceded by symbols or key words. The following is an explanation of those symbols and key words and what they mean to  
you.  
CiRClE AND SlASH SyMbOl  
This symbol means the specific action  
shown is prohibited. Ignoring these prohi-  
bitions can result in serious or fatal injury.  
DANgER  
The safety alert symbol accompanied by the word  
“DANGER” calls attention to an act or condition  
which WILL lead to serious personal injury or  
death if not avoided.  
NOTE  
wARNiNg  
This enclosed message provides tips for use, care  
and maintenance of the unit.  
The safety alert symbol accompanied by the word  
WARNING” calls attention to an act or condi-  
tion which CAN lead to serious personal injury or  
death if not avoided.  
IMPORTANT  
The enclosed message provides information nec-  
essary for the protection of the unit.  
CAUTiON  
The safety alert symbol accompanied by the word  
“CAUTION” calls attention to an act or condition  
which may lead to minor or moderate personal  
injury if not avoided.  
In T e r n a T Io n a l s y m b o l s  
Symbol  
description/application  
Symbol  
description/application  
Symbol form/shape  
Symbol form/shape  
Symbol  
Symbol  
description/application  
Symbol form/shape  
Symbol form/shape  
description/application  
ignition  
Emergency stop  
ON/OFF  
Read and understand  
Operator's Manual.  
Fuel and oil mixture  
Finger Severing  
Carburetoradjustment  
- low speed mixture  
wear eyes, ears and  
head protection  
Primer bulb  
wear hand  
protection. Use  
two handed.  
Carburetor adjustment  
- High speed mixture  
Carburetor adjustment  
- idle speed  
Hot  
Surface  
Choke Control  
"Run"  
Position  
Choke Control  
"Cold Start"  
Position  
wear slip resistant  
foot wear.  
Safety/Alert  
(Choke Open)  
(Choke Closed)  
or sparks near fuel.  
DO NOT smoke  
near fuel.  
DO NOT allow flames  
idle Speed  
Fast Speed  
p e r s o n a l C o n d IT Io n a n d s a f e T y e q u Ip m e n T  
wARNiNg  
SHRED'N'VAC® users risk injury to themselves and others if the SHRED'N'VAC® is used improperly and/or safety  
precautions are not followed. Proper clothing and safety gear must be worn when operating SHRED'N'VAC® .  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4
Physical Condition  
Your judgment and physical dexterity may not be good:  
• if you are tired or sick,  
• if you are taking medication,  
• if you have taken alcohol or drugs.  
Operate unit only if you are physically and mentally well.  
Eye Protection  
Wear eye protection that meets ANSI Z87.1 or CE requirements whenever you operate the unit.  
Hand Protection  
Wear no-slip, heavy-duty work gloves to improve your grip on the blower handle. Gloves also reduce the transmission  
of machine vibration to your hands.  
Breathing Protection  
Wear a facemask to protect against dust.  
Hearing Protection  
ECHO recommends wearing hearing protection whenever unit is used.  
Proper Clothing  
Wear snug fitting, durable clothing;  
• Pants should have long legs, shirts with long sleeves.  
• DO NOT WEAR SHORTS,  
• DO NOT WEAR TIES, SCARVES, and JEWELRY.  
Wear sturdy work shoes with nonskid soles:  
• DO NOT WEAR OPEN TOED SHOES,  
• DO NOT OPERATE UNIT BAREFOOTED.  
Keep long hair away from engine and blower intake. Retain hair with cap or net.  
Hot Humid Weather  
Heavy protective clothing can increase operator fatigue, which may lead to heat stroke. Schedule heavy work for early  
morning or late afternoon hours when temperatures are cooler.  
Vibration and Cold  
It is believed that a condition called Raynaud’s Phenomenon, which affects the fingers of certain individuals, may be  
brought about by exposure to vibration and cold. Exposure to vibration and cold may cause tingling and burning sen-  
sations, followed by loss of color and numbness in the fingers. The following precautions are strongly recommended,  
because the minimum exposure, which might trigger the ailment, is unknown.  
• Keep your body warm, especially the head, neck, feet, ankles,  
hands, and wrists.  
• Maintain good blood circulation by performing vigorous arm  
exercises during frequent work breaks, and also by not smoking.  
• Limit the hours of operation. Try to fill each day with jobs where  
operating the unit or other hand-held power equipment is not  
required.  
• If you experience discomfort, redness, and swelling of the fingers  
followed by whitening and loss of feeling, consult your physician  
before further exposing yourself to cold and vibration.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
®
Sh r e d 'N'Va c  
Op e r a t O r 'S Ma N u a l  
5
Repetitive Stress Injuries  
It is believed that overusing the muscles and tendons of the fingers, hands, arms, and shoulders may cause soreness,  
swelling, numbness, weakness, and extreme pain in those areas. Certain repetitive hand activities may put you at a high  
risk for developing a Repetitive Stress Injury (RSI). An extreme RSI condition is Carpal Tunnel Syndrome (CTS), which  
could occur when your wrist swells and squeezes a vital nerve that runs through the area.  
Some believe that prolonged exposure to vibration may contribute to CTS. CTS can cause severe pain for months or  
even years.  
To reduce the risk of RSI/CTS, do the following:  
• Avoid using your wrist in a bent, extended, or twisted position.  
Instead try to maintain a straight wrist position. Also, when  
grasping, use your whole hand, not just the thumb and index  
finger.  
• Take periodic breaks to minimize repetition and rest your hands.  
• Reduce the speed and force with which you do the repetitive  
movement.  
• Do exercises to strengthen the hand and arm muscles.  
• Immediately stop using all power equipment and consult a doc-  
tor if you feel tingling, numbness, or pain in the fingers, hands,  
wrists, or arms. The sooner RSI/CTS is diagnosed, the more  
likely permanent nerve and muscle damage can be prevented.  
DANgER  
Do not operate this product indoors or in inadequately ventilated  
areas. Engine exhaust contains poisonous emissions and can cause  
serious injury or death.  
Read the Manuals  
• Provide all users of this equipment with the Operator’s Manual  
and Safety Manual for instructions on Safe Operation.  
Clear the Work Area  
• Spectators and fellow workers must be warned, and children and  
animals prevented from coming nearer than 15 m (50 ft.) while  
the unit is in use.  
• Take wind conditions into account: avoid open doors and win-  
dows.  
• Do not point blower at people or animals.  
• Review area to be cleared. Look for potential hazards such as  
stones or metal objects.  
Keep a Firm Grip  
• Hold the handle in one hand, with thumb and fingers encircling  
the handle.  
Keep a Solid Stance  
• Maintain footing and balance at all times. Do not stand on slip-  
pery, uneven or unstable surfaces. Do not work in odd positions  
or on ladders. Do not over reach.  
Avoid Hot Surfaces  
• Keep exhaust area clear of flammable debris. Avoid contact dur-  
ing and immediately after operation.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6
e q u Ip m e n T C h e C k  
wARNiNg  
Use only ECHO approved attachments. Serious injury may result from the use of a non-approved attachment combi-  
nation. ECHO, INC. will not be responsible for the failure of cutting devices, attachments or accessories which have  
not been tested and approved by ECHO. Read and comply with all safety instructions listed in this manual and safety  
manual.  
• Check unit for loose/missing nuts, bolts and screws. Tighten and/or replace as needed.  
• Do not use blower if any part is missing or damaged.  
• Have repairs done only by an authorized ECHO Service dealer.  
• Do not use any attachment, accessory or replacement part unless it is recommended in this Operator's Manual.  
wARNiNg  
Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all  
openings.  
ALWAYS stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop  
before removing obstructions, clearing debris, or servicing unit.  
DO NOT start or operate unit unless all guards and protective covers are properly assembled to unit.  
NEVER reach into any opening while the engine is running. Moving parts may not be visible through openings.  
wARNiNg  
Check fuel system for leaks due to fuel tank damage, especially if the unit is dropped. If damage or leaks are found,  
do not use unit, otherwise serious personal injury or property damage may occur. Have unit repaired by an authorized  
servicing dealer before using.  
em Is s Io n Co n T r o l (e x h a u s T & e v a p o r a T Iv e )  
EPA 2010 and Later  
The emission control system for the engine is EM/TWC (Engine Modification and 3-way Catalyst) and for the fuel tank  
the Control System is EVAP (Evaporative Emissions) or N (for nylon tank). Evaporative emission may be applicable to  
California models only.  
An Emission Control Label is located on the unit. (This is  
an EXAMPLE ONLY; information on label varies by engine  
FAMILY).  
PRODUCT EMISSION DURABILITY (EMISSION COMPLIANCE PERIOD)  
The 300 hour emission compliance period is the time span selected by the manufacturer certifying the engine emis-  
sions output meets applicable emissions regulations, provided that approved maintenance procedures are followed as  
listed in the Maintenance Section of this manual.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
®
Sh r e d 'N'Va c  
Op e r a t O r 'S Ma N u a l  
7
de s C r Ip T Io n  
Locate the safety decal on your unit. Make sure the decals are legible and that you understand and follow the instruc-  
tions on them. If a decal cannot be read, a new one can be ordered from your ECHO dealer. See PARTS ORDERING  
instructions for specific information.  
10  
16  
2
3
1
4
15  
17  
9
8
11  
12  
7
13  
5
6
14  
1
Hot Decal (near muffler and engine)  
P/N X505002310  
General Warning Decal (located on  
blower housing)  
4
Sound Label (located on blower  
housing)  
P/N X505002080  
P/N X508000130  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8
1. SAFETY DECAL - Lists important safety precautions.  
2. STOP SWITCH - "SLIDE SWITCH" mounted on top of handle. Push forward to start and run. Slide back to stop.  
3. SPARK PLUG - Provides spark to ignite fuel mixture.  
4. SAFETY DECAL - Lists important safety precautions.  
5. FUEL TANK CAP - Covers and seals fuel tank.  
6. RECOIL STARTER HANDLE - Pull recoil handle slowly until recoil starter engages, then quickly and firmly.  
When engine starts, return handle slowly. DO NOT let handle snap back or damage to unit will occur.  
7. SPARK ARRESTOR MUFFLER OR SPARK ARRESTOR MUFFLER WITH CATALYST -The muffler or  
catalytic muffler controls exhaust noise and emission. The spark arrestor screen prevents hot, glowing particles of  
carbon from leaving the muffler. Keep exhaust area clear of flammable debris.  
8. CHOKE - Choke is located on top of the air cleaner. Move choke lever to "COLD START" (  
for cold starting. Move choke lever to "RUN" ( ) position to open choke.  
) to close choke  
9. PURGE BULB - Pumping purge bulb before starting engine draws fresh fuel from the fuel tank, purging air from  
the carburetor. Pump purge bulb until fuel is visible and flows freely in the clear fuel tank return line. Pump purge  
bulb an additional 4 or 5 times..  
10. BLOWER PIPES - Exclusive positive locking system.  
11. THROTTLE POSITION LEVER - Pull back to increase engine speed. Friction washers maintain throttle lever  
setting.  
12. THROTTLE TRIGGER - Spring loaded to return to idle when released. During acceleration, press trigger gradu-  
ally for best operating technique.  
13. AIR CLEANER - Contains replaceable air filter element.  
14. LOCKING RING - Locks blower pipe.  
15. SHOULDER STRAP - Secures debris bag to sholder.  
16. VACUUM TUBE - Sucks in materials to be shredded.  
17. DEBRIS BAG - Collects shredded material.  
SHRED'N'VAC®  
Co n T e n T s  
Operator's Manual  
MODEL  
ES-255  
1 - Power Head  
WARNING  
Read rules for safeoperationandinstructions carefully. ECHOprovidesthisOperator's  
Manual,whichmustbereadandunderstoodforproperand safe operation.  
1 - Blower Pipe (upper)  
1 - Blower Pipe (lower)  
1 - SHRED 'N' VAC® Suction Tube  
1 - Elbow Pipe  
X753002680  
08/06  
X7531180000  
1 - Debris Bag  
1 - Operator's Manual  
1 - Warranty Registration Card  
1 - Echo Power Blend X TM 2-stroke oil sample  
Download from Www.Somanuals.com. All Manuals Search And Download.  
®
Sh r e d 'N'Va c  
9
Op e r a t O r 'S Ma N u a l  
as s e m b l y  
wARNiNg  
Never perform maintenance or assembly procedures with engine  
running or serious personal injury may result.  
b l o w e r a p p l IC a T Io n  
Install Blower Pipes  
1. Stand unit upright on blower base.  
2. Release locking ring (C) with a coin or screwdriver, and rotate so  
that lock symbol (A) is at top of ring.  
3. Align locking ribs (E) on upper blower pipe with recesses (D) in  
locking ring, and slide upper blower pipe into locking ring.  
blower pipe (upper)  
4. After inserting upper blower pipe into fan case so that line (F)  
meets locking ring (C), rotate locking ring clockwise 1/8 turn to  
lock upper blower pipe in place.  
5. Align tabs (H) with grooves (G) and slide lower blower pipe over  
upper pipe until there is light resistance. Do not force connection.  
6. Hold upper pipe, and turn lower pipe clockwise, engaging posi-  
tive locking channels until connection is firm. Do not force con-  
nection.  
NOTE  
Blower use will eventually loosen pipe connections. Exclusive  
positive locking system allows pipes to be tightened. If loosening  
occurs, remove lower straight pipe, and install according to instruc-  
tions 5 & 6.  
blower pipe (upper)  
blower pipe (lower)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
10  
v a C u u m /s h r e d d In g a p p l IC a T Io n  
Remove Blower Pipes  
1. Release locking ring (C) with a coin or screwdriver, and rotate  
ring so that lock symbol (A) is at top of ring.  
2. Remove pipes from locking ring.  
Install Vacuum Tube  
1. Turn knob (I) counter clockwise until hinged housing cover is  
free to open for vacuum tube installation.  
2. Opening housing cover, slide recess (J) on vacuum tube into  
locking rib (K), and turn the vacuum tube clockwise so that it is  
locked.  
NOTE  
Engine will not start/operate unless safety interlock switch (K) is  
activated by the vacuum tube.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
®
Sh r e d 'N'Va c  
11  
Op e r a t O r 'S Ma N u a l  
Install Bag  
1. Stand unit upright on blower base.  
2. Release locking ring (C) with a coin or screwdriver, and rotate so  
that lock symbol (A) is at top of ring.  
3. Align locking ribs (L) on elbow with recesses (D) in locking ring,  
and slide elbow into locking ring.  
4. After inserting elbow into fan case so that line (M) meets locking  
ring (C), rotate locking ring clockwise 1/8 turn to lock elbow in  
place.  
5. Place debris bag opening over flared end of elbow, and cinch bag  
(O) securely at the position (N) with Velcro strap.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
12  
op e r a T Io n  
wARNiNg  
Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all  
openings. Always stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop  
before removing obstructions, clearing debris, or servicing unit. Blower housing may contain shredder blades and  
other sharp edges that can cause serious injuries if touched, even if engine is off and blades are not moving. Wear  
gloves to protect hands from sharp edges and hot surfaces.  
wARNiNg  
Operation of this equipment may create sparks that can start fires around dry vegetation. This unit is equipped  
with a spark arrestor and a spark arrestor may be required. The operator should contact local fire agencies for  
laws or regulations relating to fire prevention requirements.  
f u e l  
NOTICE: Use of unmixed, improperly mixed, or fuel older than 90 days, (stale fuel), may cause hard starting, poor  
performance, or severe engine damage and void the product warranty. Read and follow instructions in the Storage  
section of this manual.  
wARNiNg  
Alternative fuels, such as E-15 (15% ethanol), E-85 (85% ethanol) or any fuels not meeting ECHO requirements are  
NOT approved for use in ECHO 2-stroke gasoline engines. Use of alternative fuels may cause performance prob-  
lems, loss of power, overheating, fuel vapor lock, and unintended machine operation, including, but not limited to,  
improper clutch engagement. Alternative fuels may also cause premature deterioration of fuel lines, gaskets, carbu-  
retors and other engine components.  
Fuel Requirements  
Gasoline - Use 89 Octane [R+M/2] (mid grade or higher) gasoline known to be good quality. Gasoline may contain up to  
10% Ethanol (grain alcohol) or 15% MTBE (methyl tertiary-butyl ether). Gasoline containing methanol (wood alcohol)  
is NOT approved.  
Two Stroke Oil - A two-stroke engine oil meeting ISO-L-EGD (ISO/CD 13738) and J.A.S.O. FC/FD Standards must  
be used. Echo brand premium Power Blend X TM Universal 2-Stroke Oil meets these standards. Engine problems due to  
inadequate lubrication caused by failure to use an ISO-L-EGD (ISO/CD 13738) and J.A.S.O. FC/FD certified oil, such  
as Echo premium Power Blend X TM, will void the two-stroke engine warranty.  
IMPORTANT  
Echo premium Power Blend X TM Universal 2-Stroke Oil may be mixed at 50:1 ratio for application in all Echo en-  
gines sold in the past regardless of ratio specified in those manuals.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
®
Sh r e d 'N'Va c  
13  
Op e r a t O r 'S Ma N u a l  
Handling Fuel  
DANgER  
Fuel is VERY flammable. Use extreme care when mixing, storing or handling or serious personal injury may result.  
• Use an approved fuel container.  
• DO NOT smoke near fuel.  
• DO NOT allow flames or sparks near fuel.  
• Fuel tanks/cans may be under pressure. Always loosen fuel caps slowly allowing pressure to equalize.  
• NEVER refuel a unit when the engine is HOT or RUNNING!  
• DO NOT fill fuel tanks indoors. ALWAYS fill fuel tanks outdoors over bare ground.  
• DO NOT overfill fuel tank. Wipe up spills immediately.  
• Securely tighten fuel tank cap and close fuel container after refueling.  
• Inspect for fuel leakage. If fuel leakage is found, do not start or operate unit until leakage is repaired.  
• Move at least 3m (10 ft.) from refueling location before starting the engine.  
Mixing Instructions  
1. Fill an approved fuel container with half of the required amount  
of gasoline.  
2. Add the proper amount of 2-stroke oil to gasoline.  
3. Close container and shake to mix oil with gasoline.  
4. Add remaining gasoline, close fuel container, and remix.  
IMPORTANT  
Spilled fuel is a leading cause of hydrocarbon emissions. Some  
states may require the use of automatic fuel shut-off containers  
to reduce fuel spillage.  
After use  
• DO NOT store a unit with fuel in its tank. Leaks can occur. Return  
unused fuel to an approved fuel storage container.  
Shoulder  
level  
Fuel tank  
Storage - Fuel storage laws vary by locality. Contact your local gov-  
ernment for the laws affecting your area. As a precaution, store fuel in  
an approved, airtight container. Store in a well-ventilated, unoccupied  
building, away from sparks and flames.  
IMPORTANT  
Stored fuel ages. Do not mix more fuel than you expect to use in  
thirty (30) days, ninety (90) days when a fuel stabilizer is added.  
IMPORTANT  
Stored two-stroke fuel may separate. ALWAYS shake fuel con-  
tainer thoroughly before each use.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
14  
s T a r T In g C o l d e n g In e  
1. Stop Switch  
Move stop switch button (A) away from the STOP position.  
A
b
2. Throttle Position Lever  
Move throttle position lever (B) midway between idle and full  
throttle positions.  
3. Choke  
Move choke (C) to Cold Start (  
) Position.  
4. Purge Bulb  
C
Pump purge bulb (D) until fuel is visible and flows freely in the  
clear fuel tank return line.  
D
IMPORTANT  
Recoil starter: Use short pulls - only 1/2 ~ 2/3 of rope for start-  
ing. Do not allow the rope to snap back in. Always hold the unit  
firmly.  
5. Recoil Starter  
Place the unit on a flat, clear area. Firmly grasp throttle grip with  
left hand and rapidly pull recoil starter handle/rope (E) until en-  
gine fires, or maximum 5 pulls.  
6. Choke  
Move choke lever (C) to Run (  
engine.  
) position if necessary, restart  
E
NOTE  
If engine does not start after 5 pulls, repeat instructions 3-6.  
7. After engine warm up, gradually depress throttle trigger to in-  
crease engine RPM to operating speed.  
NOTE  
C
Allow engine to warm up before use.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
®
Sh r e d 'N'Va c  
15  
Op e r a t O r 'S Ma N u a l  
s T a r T In g w a r m e n g In e  
The starting procedure is the same as Cold Start except DO NOT close  
the choke.  
A
b
1. Stop Switch  
Move stop switch button (A) away from the STOP position.  
2. Throttle Position Lever  
Move throttle position lever (B) midway between idle and full  
throttle positions.  
3. Purge Bulb  
Pump purge bulb (D) until fuel is visible and flows freely in the  
clear fuel tank return line.  
4. Recoil Starter  
D
Place the unit on a flat, clear area. Firmly grasp throttle grip with  
left hand and rapidly pull recoil starter handle/rope (E) until en-  
gine fires.  
IMPORTANT  
Recoil starter: Use short pulls - only 1/2 ~ 2/3 of rope for start-  
ing. Do not allow the rope to snap back in. Always hold the unit  
firmly.  
NOTE  
If engine does not start after 5 pulls, use Cold Start Procedure.  
E
s T o p p In g e n g In e  
A
1. Throttle Trigger/Throttle Position Lever  
Release throttle trigger (F). Move throttle position lever (B)  
forward to idle position and allow engine to return to idle before  
shutting off engine.  
F
b
2. Stop Switch  
Move stop switch (A) to “STOP” position.  
wARNiNg  
If engine does not stop when stop switch is moved to STOP posi-  
tion, close choke - COLD START position - to stall engine. Have  
your ECHO dealer repair stop switch before using blower again.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
16  
o p e r a T In g b l o w e r  
wARNiNg  
Engine exhaust IS HOT, and contains Carbon Monoxide (CO), a  
poison gas. Breathing CO can cause unconsciousness, serious in-  
jury, or death. Exhaust can cause serious burns. ALWAYS position  
unit so that exhaust is directed away from your face and body.  
wARNiNg  
Always wear safety glasses, hearing protection and a face filter  
mask or serious personal injury may result. Do not point the blower  
pipe in the direction of people or pets.  
IMPORTANT  
Use reduced speed only when performing light-duty tasks or  
to comply with local noise regulations. Continuous low speed  
operation may allow fuel/oil residue to build-up on the piston  
and cause rapid build-up of carbon on the spark arrestor screen,  
resulting in overheating and engine damage. To reduce harmful  
build-up, run engine at wide open throttle for at least 5 minutes  
every hour, and inspect/clean the spark arrestor screen after ap-  
proximately 40 hours of operation.  
F
b
Read the Safety Section carefully.  
IMPORTANT  
To avoid engine damage due to over-revving, do not block  
blower pipe.  
1. Use only during appropriate hours.  
2. Allow the engine to warm up at a fast idle for a few minutes.  
3. Control engine speed with throttle trigger (F), or for continu-  
ous use, set engine speed with throttle position lever (B). Rotate  
throttle position lever forward for lower speed, back for higher  
speed.  
4. Use lower speed to blow debris from hard surfaces.  
5. Additional speed may be necessary to clean debris, snow, etc.  
from lawns and flowerbeds.  
NOTE  
Never use a higher speed setting than necessary to perform a task.  
Remember, the higher the engine speed, the louder the blower  
noise. Minimize dust by using blower at lower speeds. Keep debris  
on your property.  
Be Smart - be a good neighbor.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
®
Sh r e d 'N'Va c  
17  
Op e r a t O r 'S Ma N u a l  
®
s h r e d 'n' v a C o p e r a T Io n  
wARNiNg  
Flying debris hazard. Never operate unit as a vacuum unless  
discharge elbow is installed and debris bag is securely cinched to  
elbow. Failure to follow instructions can result in serious injuries.  
wARNiNg  
Debris bag is flammable and could be ignited if allowed to contact  
hot muffler cover or exhaust. Keep bag away from hot surfaces at  
all times.  
1. Adjust debris bag strap to support bag on operator’s shoulder.  
Bag must not be folded at intake area, or intake will clog. Further  
adjustment may be necessary as the debris bag fills and becomes  
heavier.  
2. Grip throttle control handle with left hand, and lower handle/  
stand with right hand.  
NOTE  
3. Operate unit with beveled end of tube facing downward. Keep  
tube opening close to material being vacuumed for best results.  
4. Empty bag when debris level reaches intake opening. To empty  
bag, move stop switch to “Stop” position, and wait for blower  
to stop running. Loosen Velcro strap at elbow and slide bag off  
elbow. Open other end of bag, and empty contents. Close bag,  
and reattach to blower. Secure bag with Velcro strap.  
Vacuum action works best at higher  
engine speeds. Avoid using vacuum in  
areas where rocks or other large, hard  
debris may be vacuumed into unit. Clear  
these areas with blower first, blowing  
light debris into a pile. Use attachment  
to vacuum pile.  
®
s h r e d 'n' v a C T r o u b l e s h o o T In g  
Problem  
Cause  
Remedy  
Check elbow and debris bag, and clear  
as needed. Make sure bag is not folded  
over at intake during use.  
Unit runs, but doesn’t vacuum or  
has poor suction  
Elbow or debris bag clogged  
Check vacuum tube, and remove ob-  
structions. Avoid wet leaves.  
Obstructions in vacuum tube  
Unit stopped suddenly during vacu-  
uming, and now starter won’t work  
Remove vacuum tube and check fan  
area. Remove object.  
Object stuck in fan housing area  
Use vacuum for leaves and small  
twigs, maximum 1/4” diameter x 3”  
long.  
Material being vacuumed too big or  
too hard for blades to shred  
Unit jams repeatedly during use  
Tube/housing fit tight.  
Vacuum tube difficult to install or  
remove from unit  
Apply small amount of soapy water  
to end of tube to ease assembly or  
removal. Turns tube 1/4 turn to loosen  
for removal.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
18  
ma In T e n a n C e  
wARNiNg  
Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all  
openings. Always stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop  
before removing obstructions, clearing debris, or servicing unit. Allow unit to cool before performing service. Wear  
gloves to protect hands from sharp edges and hot surfaces.  
Your ECHO blower is designed to provide many hours of trouble free service. Regular scheduled maintenance will help  
your blower achieve that goal. If you are unsure or are not equipped with the necessary tools, you may want to take your  
unit to an ECHO Service Dealer for maintenance. To help you decide whether you want to DO-IT-YOURSELF or have  
the ECHO Dealer do it, each maintenance task has been graded. If task is not listed, see your ECHO Dealer for repairs.  
s k Il l l e v e l  
Level 1 =  
Level 2 =  
Easy to do. Common tools may be required.  
Moderate difficulty. Some specialized tools may be required.  
ECHO offers REPOWERTM Maintenance Kits and Parts to make your maintenance job easier.  
m a In T e n a n C e In T e r v a l s  
REQ'D  
SKILL  
LEVEL  
3 MONTHS  
OR 90  
HOURS  
MAINTENANCE  
PROCEDURE  
DAILY OR  
BEFORE USE REFUEL  
EVERY  
YEARLY  
600 HOURS  
COMPONENT / SYSTEM  
Air Filter  
Inspect/Clean  
1
1
1
1
1
1
2
2
2
1
1
I / C *  
I / C  
R *  
Choke Shutter  
Fuel Filter  
Inspect/Clean  
Inspect/Replace  
I *  
I *  
I / R *  
R *  
Fuel Cap Gasket  
Fuel System  
Inspect/Replace  
Inspect/Replace  
I (1) *  
I / C  
I (1) *  
Spark Plug  
Inspect/Clean/Replace  
Inspect/Clean  
I / C / R *  
Cooling System  
Muffler Spark Arrestor  
Cylinder Exhaust Port  
Recoil Starter Rope  
Screws/Nuts/Bolts  
Inspect/Clean/Replace  
Inspect/Clean/Decarbon  
Inspect/Clean  
I / C / R *  
I / C  
I / C *  
I *  
Inspect/Tighten/Replace  
MAINTENANCE PROCEDURE LETTER CODES: I = INSPECT, R = REPLACE, C = CLEAN  
IMPORTANT NOTE - Time intervals shown are maximum. Actual use and your experience will determine the  
frequency of required maintenance.  
MAINTENANCE PROCEDURE NOTES:  
(1) Low evaporative fuel tanks DO NOT require regular maintenance to maintain emission integrity.  
* All recommendations to replace are based on the finding of damage or wear during inspection.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
®
Sh r e d 'N'Va c  
19  
Op e r a t O r 'S Ma N u a l  
a Ir f I l T e r  
Level 1.  
Tools required: 25-50 mm (1-2 in.) Cleaning brush.  
Parts required: REPOWERTM AIR & FUEL FILTER KIT.  
NOTE  
Clean daily.  
1. Close choke (Cold Start Position [ ]). This prevents dirt from  
entering the carburetor throat when the air filter is removed. Brush  
accumulated dirt from air cleaner area.  
2. Remove air filter cover. Brush dirt from inside cover.  
3. Remove air filter and lightly brush debris from filter. Replace  
filter if it is damaged, fuel soaked, very dirty, or the rubber sealing  
edges are deformed.  
4. If filter can be reused, be certain it:  
• Fits tightly in the air filter cavity.  
• Is installed with the original side out.  
5. Install air filter cover.  
f u e l f I l T e r  
Level 1.  
Tools required:  
200-250 mm (8-10 in.) length of wire with one end  
bent into a hook. Clean rag, funnel, and an approved  
fuel container.  
Parts required: REPOWERTM AIR & FUEL FILTER KIT.  
DANgER  
Fuel is VERY flammable. Use extreme care when mixing, storing  
or handling.  
1. Use a clean rag to remove loose dirt from around fuel cap and  
empty fuel tank.  
2. Use the “fuel line hook” to pull the fuel line and filter from the  
tank.  
3. Remove the filter from the line and install the new filter.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
20  
s p a r k p l u g  
Level 2.  
Tools required:  
T-Wrench, Feeler gauge  
Parts Required: REPOWERTM Tune-Up Kit  
IMPORTANT  
Use only NGK BPM8Y spark plug otherwise severe engine  
damage may occur.  
1. Remove spark plug and check for fouling, worn and rounded  
center electrode.  
2. Clean the plug or replace with a new one. DO NOT sand blast to  
clean. Remaining sand will damage engine.  
0.65 mm  
(0.026 in.)  
3. Adjust spark plug gap by bending outer electrode.  
4. Tighten spark plug to 150-170 kgf • cm (130-150 in • lbf).  
C o o l In g s y s T e m  
Level 2.  
Tools required: 25-50 mm (1-2 in.) cleaning brush, 4 mm Hex  
Wrench.  
Parts Required: None, if you are careful.  
IMPORTANT  
To maintain proper engine operating temperatures, cooling air must  
pass freely through the cylinder fin area. This flow of air carries  
combustion heat away from the engine.  
Overheating and engine seizure can occur when:  
• Air intakes are blocked, preventing cooling air from reaching the  
cylinder.  
• Dust and grass build up on the outside of the cylinder. This build up  
insulates the engine and prevents the heat from leaving.  
Removal of cooling passage blockages or cleaning of cooling fins is  
considered “Normal Maintenance”. Any failure attributed to lack of  
maintenance is not warranted.  
Cleaning Grill  
1. Brush accumulated debris from crankcase intake grill above the  
fuel tank.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
®
Sh r e d 'N'Va c  
21  
Op e r a t O r 'S Ma N u a l  
Cleaning Cylinder Fins  
1. Remove engine cover (two screws), pull cover away from engine.  
Clean cylinder fins to allow cooling air to pass freely.  
2. Loosely reassemble engine cover with two screws.  
3. Tighten all screws securely.  
e x h a u s T s y s T e m  
Spark Arrestor Screen  
Level 2.  
Tools required: Cross Head Screwdriver, 4 mm Hex Wrench, Soft  
metal brush  
Parts Required: Spark arrestor screen, Gasket  
E
D
1. Remove engine cover (two screws), pull cover away from engine.  
Clean cylinder fins with brush to allow cooling air to pass freely.  
C
b
2. Remove spark arrestor cover (A), deflector (B), plate (C), gasket  
(D), and spark arrestor screen (E) from muffler. Replace screen if  
plugged with carbon deposits.  
A
NOTE  
When cleaning carbon deposit, be careful not to damage the cata-  
lytic element inside muffler.  
3. Install spark arrestor screen, gasket, plate, deflector, and cover.  
4. Loosely reassemble engine cover with two screws.  
5. Tighten all screws securely.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
22  
Exhaust Port Cleaning  
Level 2.  
Tools required: 4 mm Hex Wrench., Wood or plastic scraper  
Parts Required: As needed: Heat Shield  
1.  
2.  
3.  
Remove spark plug lead from spark plug, and remove engine  
cover (2 screws).  
A
b
Place piston at top dead center. Remove muffler (A) and heat  
shield (B).  
Use a wood or plastic scraping tool to clean deposits from cylin-  
der exhaust port.  
IMPORTANT  
Never use a metal tool to scrape carbon from the exhaust port.  
Do not scratch the cylinder or piston when cleaning the exhaust  
port. Do not allow carbon particles to enter the cylinder.  
4.  
5.  
6.  
Inspect heat shield, and replace if damaged.  
Install heat shield and muffler.  
Tighten muffler mounting bolts (or nuts) to 60-70 in•lbf (70-80  
kgf•cm).  
7.  
Install engine cover and attach spark plug lead.  
Start engine, and warm to operating temperature.  
8.  
9.  
Stop engine, and re-tighten mounting bolts (or nuts) to specifica-  
tions.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
®
Sh r e d 'N'Va c  
23  
Op e r a t O r 'S Ma N u a l  
s h r e d d e r b l a d e  
Level 1.  
wARNiNg  
Never remove vacuum tube or open fan guard when SHRED ‘N’  
VAC® is running or serious personal injury may result. Always  
wear heavy-duty work gloves when working in shredder blade area.  
1.  
2.  
With engine stopped, remove spark plug wire, remove vacuum  
tube from unit.  
Remove accumulated debris from blade and inspect for damage.  
IMPORTANT  
Do not operate SHRED ‘N’ VAC® if shredder blade is damaged  
or broken. Return unit to Echo Dealer for service.  
3.  
Install vacuum tube. Refer to “Install Vacuum Tube and Bag  
Assembly” (page 9) in assembly section for correct assembly  
procedures.  
d e b r Is b a g  
Level 1.  
Parts Required: None  
Shake dust from bag and inspect for hole or tears. Inspect zipper and  
clean debris from teeth to assure complete closing of zipper.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
24  
C a r b u r e T o r a d j u s T m e n T  
Engine Break-In  
New engines must be operated a minimum duration of two tanks of fuel  
break-in before carburetor adjustments can be made. During the break-  
in period your engine performance will increase and exhaust emissions  
will stabilize. Idle speed can be adjusted as required.  
High Altitude Operation  
This engine has been factory adjusted to maintain satisfactory starting,  
emission, and durability performance up to 1,100 feet above sea level  
(ASL) (96.0 kPa). To maintain proper engine operation and emission  
compliance above 1,100 feet ASL the carburetor may need to be ad-  
justed by an authorized ECHO service dealer.  
IMPORTANT  
If the engine is adjusted for operation above 1,100 feet ASL, the  
carburetor must be re-adjusted when operating the engine below  
1,100 feet ASL, otherwise severe engine damage may result.  
Level 2.  
Tools required: Screwdriver, tachometer (Echo P/N 99051130017)  
Parts required: None.  
NOTE  
Every unit is run at the factory and the carburetor is set in compli-  
ance with emission regulations. Carburetor adjustments, other than  
idle speed, must be performed by an authorized ECHO dealer.  
Idle Adjustment  
Before adjustment make sure that:  
Air filter is clean and properly installed.  
Spark arrestor screen is free of carbon.  
Blower pipes are installed.  
1. Start engine, run at idle for one minute.  
2. Complete warm up by running at full throttle for 5 minutes, oper-  
ating choke twice to clear air from carburetor chambers.  
3. Check idle speed and reset if necessary. If a tachometer is avail-  
able, idle speed screw (A) should be set to the specifications  
found on Page 27"Specifications" of this manual. Turn idle screw  
(A) clockwise to increase idle speed; counter clockwise to de-  
crease idle speed.  
A
Download from Www.Somanuals.com. All Manuals Search And Download.  
®
Sh r e d 'N'Va c  
25  
Op e r a t O r 'S Ma N u a l  
Tr o u b l e s h o o T In g  
TROUblESHOOTiNg CHART  
Problem  
Check  
Status  
Cause  
Remedy  
Clean or replace  
Clean or replace  
See your Echo dealer  
Fuel at carburetor  
No fuel at carburetor  
Fuel strainer clogged  
Fuel line clogged  
Carburetor  
Fuel at cylinder  
No fuel at cylinder  
Muffler wet with fuel  
Carburetor  
See your Echo dealer  
Fuel Mixture too rich  
Open choke  
Clean/replace air filter  
Adjust carburetor  
See your Echo dealer  
Engine cranks -  
starts hard/  
doesn't  
start  
Spark at end  
of plug wire  
No spark  
No spark  
Stop switch off  
Electrical problem  
Interlock switch  
Turn switch to ON  
See your Echo dealer  
See your Echo dealer  
Spark at plug  
Spark gap incorrect  
Covered with carbon  
Fouled with fuel  
Adjust to .65mm (0.026 in.)  
Clean or replace  
Clean or replace  
Plug defective  
Replace plug  
Air filter  
Air filter dirty  
Normal wear  
Clean or replace  
Replace  
Fuel filter  
Fuel filter dirty  
Contaminants/residues in  
fuel  
Fuel vent  
Fuel vent plugged  
Plug dirty/worn  
Contaminants/residues in fuel Clean or replace  
Engine runs,  
but dies or  
does not  
accelerate  
properly  
Spark Plug  
Normal wear  
Vibration  
Clean and adjust or replace  
Carburetor  
Improper adjustment  
Adjust  
Clean  
Cooling System  
Cooling system  
dirty/plugged  
Extended operation in  
dirty/dusty locations  
Spark Arrestor Screen  
N/A  
Spark arrestor screen Normal wear  
plugged  
Replace  
Engine does  
not crank  
N/A  
Internal engine problem  
See your Echo dealer  
Engine runs,  
blower doesn't  
work or is  
Blower pipe  
Pipe clogged  
Pipe loose  
Build-up of debris  
Vibration  
Unclog  
Tighten  
Replace  
weak/uneven  
Pipe damaged  
Wear/Misuse  
DANgER  
Fuel vapors are extremely flammable and may cause fire and/or explosion. Never test for ignition spark by ground-  
ing spark plug near cylinder plug hole, otherwise serious personal injury may result.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
26  
sT o r a g e  
wARNiNg  
During operation the muffler or catalytic muffler and surrounding cover becomes hot. Always keep exhaust area clear  
of flammable debris during transportation or when storing, otherwise serious property damage or personal injury may  
result.  
Long Term Storage (Over 30 Days)  
Do not store your unit for a prolonged period of time (30 days or longer) without performing protective storage mainte-  
nance which includes the following:  
1. Store unit in a dry, dust free place, out of the reach of children.  
DANgER  
Do not store where fuel fumes may accumulate or reach an open flame or spark.  
2. Place the stop switchs in the "STOP" position.  
3. Remove accumulation of grease, oil, dirt and debris from exterior of unit.  
4. Perform all periodic lubrication and services that are required.  
5. Tighten all screws and nuts.  
6. Drain the fuel tank completely and pull the recoil starter handle several times to remove fuel from the carburetor.  
7. Remove the spark plug and pour 7cc (1/4 oz.) of fresh, clean ECHO 2-stroke engine oil into the cylinder through  
the spark plug hole.  
A. Place a clean cloth over the spark plug hole.  
B. Pull the recoil starter handle 2-3 times to distribute the oil inside the engine.  
C. Observethepistonlocationthroughthesparkplughole.Pulltherecoilhandleslowlyuntilthepistonreachesthe  
top of its travel and leave it there.  
8. Install the spark plug (do not connect ignition cable).  
9. Remove blower/vacuum pipes from unit.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
®
Sh r e d 'N'Va c  
27  
Op e r a t O r 'S Ma N u a l  
sp e C If IC a T Io n s  
MODEL ----------------------------------------------------------ES-255  
Length ------------------------------------------------------------340 mm (13.4 in.) (w/o pipes)  
Width --------------------------------------------------------------260 mm (10.2 in.)  
Height -------------------------------------------------------------350 mm (13.8 in.)  
Weight w/blower pipes------------------------------------------4.8 kg (10.6 lb.)  
Weight w/vac pipes----------------------------------------------5.9 kg (13.0 lb.)  
Engine Type ------------------------------------------------------Air cooled, two-stroke, single cylinder gasoline engine  
Displacement -----------------------------------------------------25.4cc (1.55 cu. in.)  
Bore----------------------------------------------------------------34.0 mm (1.34 in.)  
Stroke--------------------------------------------------------------28.0 mm (1.10 in.)  
Carburetor---------------------------------------------------------Zama Diaphragm model w/purge bulb  
Ignition System --------------------------------------------------Flywheel Magneto, capacitor discharge ignition type  
Spark Plug --------------------------------------------------------NGK BPMR8Y Gap 0.65 mm (0.026 in.)  
Exhaust System --------------------------------------------------Spark arrestor muffler or spark arrestor muffler with catalyst  
Fuel ----------------------------------------------------------------Mixed (Gasoline and Two-stroke Oil)  
Fuel/Oil Ratio ----------------------------------------------------50 : 1 Power Blend X ™ ISO-L-EGD (ISO/CD 13738) and  
J.A.S.O. M345- FC/FD, two-stroke, air-cooled engine oil.  
Gasoline-----------------------------------------------------------Use 89 Octane unleaded. Do not use fuel containing methyl  
alcohol, more than 10% ethyl alcohol or 15% MTBE. Do not  
use alternative fuels such as E-15 or E-85.  
Oil------------------------------------------------------------------Power Blend X ™ Premium Universal 2-Stroke Oil  
Fuel Tank Capacity ----------------------------------------------0.5 lit. (16.9 US fl. oz.)  
Recoil Starter System -------------------------------------------Automatic Recoil Starter Centrifugal Type  
Idle Speed (RPM)------------------------------------------------2,800 - 3,200  
Wide Open Throttle Speed (RPM) ----------------------------6,000 - 6,500  
Maximum Air Speed w/pipes (MPH) -------------------------69.3 m/sec (155 mph)  
Maximum Air Volume ------------------------------------------9.7 m3/min. (342 cu. ft./min.)  
Sound Level at 50 ft. dB(A) scale per ANSI B175.2 -------70 dB(A)  
IMPORTANT  
This spark ignition system complies with the Canadian standard ICES-002.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
28  
wa r r a n T y sT a T e m e n T s  
ECHO LIMITED WARRANTY STATEMENT FOR  
PRODUCT SOLD IN USA AND CANADA BEGINNING 01/01/2010  
ECHO'S RESPONSIBILITY  
ECHO Incorporated’s Limited Warranty, provides to the original purchaser that this ECHO product is free from defects in material and workmanship.  
Under normal use and maintenance from date of purchase, ECHO agrees to repair or replace at ECHO’s discretion, any defective product  
free of charge at any authorized ECHO servicing dealer within listed below application time periods, limitations and exclusions. THIS LIMITED  
WARRANTY IS ONLYAPPLICABLE TO ECHO PRODUCTS SOLD BYAUTHORIZED ECHO DEALERS. IT IS EXTENDED TO THE ORIGINAL  
PURCHASER ONLY, AND IS NOT TRANSFERABLE TO SUBSEQUENT OWNERS EXCEPT FOR EMISSION RELATED PARTS. Repair  
parts and accessories replaced under this warranty are warranted only for the balance of the original unit or accessory warranty period. Any  
damage caused by improper installation or improper maintenance is not covered by this warranty. All parts or products replaced under warranty  
become the property of ECHO, Inc. This warranty is separate from the Emission control warranty statement supplied with your new product.  
Please consult the Emission Control Warranty Statement for details regarding emission related parts. For a list of Authorized ECHO Dealers  
refer to WWW.ECHO-USA.COM or call 1-800-432-ECHO.  
OWNER’S RESPONSIBILITY  
To ensure trouble free warranty coverage it is important that you register your ECHO equipment on-line at WWW.ECHO-USA.COM or by fill-  
ing out the warranty registration card supplied with your unit. Registering your product confirms your warranty coverage and provides a direct  
link if we find it necessary to contact you.  
The owner shall demonstrate reasonable care and use, and follow preventative maintenance, storage, fuel and oil usage as prescribed in the  
operator’s manual. Should a product difficulty occur, you must, at your expense, deliver or ship your ECHO unit to an authorized ECHO servicing  
dealer for warranty repairs (within the applicable warranty period), and arrange for pick-up or return of your unit after the repairs have been  
made. For your nearest authorized ECHO servicing dealer, call ECHO’s Dealer Referral Center, at 1-800-432-ECHO or you can locate an ECHO  
servicing dealer at WWW.ECHO-USA.COM. Should you require assistance or have questions concerning ECHO’s Warranty Statement, you  
can contact our Consumer Product Support Department at 1-800-673-1558 or contact us through the web at WWW.ECHO-USA.COM.  
PRODUCT WARRANTY PERIOD  
RESIDENTIAL APPLICATION  
5 YEAR WARRANTY - All units for residential, or non-income producing use will be covered by this limited warranty for five (5) years from  
date of purchase.  
EXCEPTIONS:  
For two-stroke engine powered products, the electronic ignition module, flexible drive cables, SRM solid drive shafts, and TC tines  
are warranted for the life* of the product on parts only.  
Cutting attachments such as, but not limited to, bars, chains, sprockets, blades, and nylon trimmer heads for residential or non-income  
producing use will be covered for failures due to defects in material or workmanship for a period of 60 days from original product  
purchase date. Any misuse from contact with concrete, rocks, or other structures is not covered by this warranty.  
ECHO’s Rapid Loader String Head carries a lifetime warranty on the line locking system, parts only; no labor. Refer to your operator’s  
manual for string head installation and maintenance instructions.  
All SB-Series and PRO ATTACHMENT SERIES Split Shaft attachments carry the same warranty duration as the units they are  
designed to fit.  
COMMERCIAL APPLICATION  
1 YEAR WARRANTY - All Chain Saws, QuikVent Saws, and Cut-Off Saws for commercial, institutional, agricultural, industrial, or income  
producing use will be covered by this limited warranty for one (1) year from the date of purchase.  
2 YEAR WARRANTY - All other units for commercial, institutional, agricultural, industrial, or income producing use will be covered by this  
limited warranty for two (2) years from the date of purchase.  
EXCEPTIONS:  
For two-stroke engine powered products, the electronic ignition module, flexible drive cables, SRM solid drive shafts and TC tines,  
are warranted for the life* of the product on parts only.  
Cutting attachments such as, but not limited to, bars, chains, sprockets, blades, and nylon trimmer heads for commercial, institutional,  
agricultural, industrial, rental, or income producing will be covered for failures due to defects in material or workmanship for a period  
of 30 days from original product purchase date. Any misuse from contact with concrete, rocks, or other structures is not covered by  
this warranty.  
ECHO’s Rapid Loader String Head carries a lifetime warranty on the line locking system, parts only; no labor. Refer to your operator’s  
manual for string head installation and maintenance instructions.  
All SB-Series and PRO ATTACHMENT SERIES Split Shaft attachments carry the same warranty duration as the units they are  
designed to fit.  
RENTAL APPLICATION - 90 DAYS WARRANTY  
• Units for rental use will be covered against defects in material and workmanship for a period of 90 days from the date of purchase.  
*
ECHO’s liability under the “Lifetime” coverage is limited to furnishing parts specified under the PROdUCT wARRANTy PERIOd section of  
this warranty statement for “Life” free of charge for a period of ten (10) years after the date of the complete unit’s final production.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
®
Sh r e d 'N'Va c  
29  
Op e r a t O r 'S Ma N u a l  
PURCHASED REPAIR PARTS, SHORT BLOCKS AND ACCESSORIES  
• 90-day residential, or non-income producing warranty  
• 30-day commercial, institutional, agricultural, industrial, income producing, or rental application warranty  
ATTENTION TWO-STROKE ENGINE POWER PRODUCT OWNERS  
This ECHO two-stroke engine power product is a quality-engineered unit which has been manufactured to exact tolerances to provide superior  
performance. To help ensure the performance of the unit, it is required to use two-stroke oil which meets the ISO-L-EGD Standard per ISO/CD  
13738 and JASO M345/FC/FD Standards. ECHO Power Blend™ Two-Stroke Oil is a premium two-stroke oil specifically formulated to meet  
ISO-L-EGD (ISO/CD 13738) and JASO M345/FC/FD Standards. The use of two-stroke oils designed for other applications, such as for outboard  
motors or lawnmowers can result in severe engine damage, and will void your two-stroke engine limited warranty.  
THIS WARRANTY DOES NOT COVER DAMAGE CAUSED BY:  
Lack of lubrication or engine failure, due to the use of two-stroke oils that do not meet the ISO-L-EGD (ISO/CD 13738) and JASO M345/  
FC/FD Standards. Engine problems due to inadequate lubrication caused by failure to use an ISO-L-EGD compliant and JASO M345/FC/  
FD registered oil, will void the two-stroke engine limited warranty. ECHO Power Blend™ Two-Stroke Oil meets the ISO-L-EGD and JASO  
M345/FC/FD Standard. Emission related parts are covered for 5 years residential use or 2 years commercial use regardless of two-stroke  
oil used, per the statement listed in the EPA or California Emission Defect Warranty Explanation.  
damage caused by use of gasohol, containing methanol (wood alcohol), or gasoline containing less than 89 octane. Only use gasoline which  
contains 89 octane or higher. Gasohol which contains a maximum 10% ethanol (grain alcohol) or 15% MTBE (methyl/tertiary/butyl/ether)  
is also approved. The prescribed mixing ratio of gasoline to oil is listed on the ECHO oil label and covered in your operator’s manual.  
Engine damage caused by use of ether or any starting fluids.  
damage caused by tampering with engine speed governor or emission components, or running engines above specified and recommended  
engine speeds as listed in your operator’s manual.  
Operation of the unit with improperly maintained/removed cutting shield or removed/damaged air filter.  
damage caused by dirt, pressure or steam cleaning the unit, salt water, corrosion, rust, varnish, abrasives, and moisture.  
defects, malfunctions or failures resulting from abuse, misuse, neglect, modifications, alterations, normal wear, improper servicing, or use  
of unauthorized attachments.  
Incorrect storage procedures, stale fuel, including failure to provide or perform required maintenance services as prescribed in the operator's  
manual. Preventative maintenance as outlined in the operators manual is the customer’s responsibility.  
Failures due to improper set-up, pre-delivery service or repair service by anyone other than authorized ECHO servicing dealer during the  
warranty period.  
Certain parts and other items are not warranted, including but not limited to: lubricants, starter cords, and engine tune-ups.  
Use of spark plugs other than those meeting performance and durability requirements of the OEM spark plug listed in the Operator's  
Manuals.  
Overheating or carbon scoring failures due to restricted, clogged exhaust port or combustion chamber, including damage to spark arrester  
screen.  
Adjustments after the first (30) thirty days and beyond, such as carburetor adjustment and throttle cable adjustment.  
damage to gears or gear cases caused by contaminated grease or oil, use of incorrect type or viscosity of lubricants, and/or failure to comply  
with recommended grease or oil change intervals.  
damage caused by loading SHREd 'N' VAC® beyond recommended capacity.  
damage caused by pump or sprayer running dry, pumping or spraying caustic or flammable materials, or lack of or broken strainers.  
Additional damage to parts or components due to continued use after operational problem or failure occurs. Should operational problem or  
failure occur, the product should not be used, but delivered as is to an authorized ECHO servicing dealer.  
It is a dealer’s and/or customer’s responsibility to complete and return the warranty registration card supplied with your ECHO product or by visiting  
WWW.ECHO-USA.COM. your receipt of purchase including date, model and serial number must be maintained and presented to an authorized  
ECHO servicing dealer for warranty service. Proof of purchase rests solely with the customer. Some states do not allow limitations on how long  
an implied warranty lasts, so the above limitations may not apply to you. Some states do not allow the exclusion or limitation of incidental or  
consequential damages, so you may also have other specific legal rights which vary from state to state. This limited warranty is given by ECHO  
Incorporated, 400 Oakwood Rd., Lake Zurich, IL 60047.  
DISCLAIMER OF IMPLIED WARRANTIES  
This limited warranty is in lieu of all other expressed or implied warranties, including any warranty of FITNESS FOR A PARTICULAR PURPOSE  
OR USE and any implied warranty of MERCHANTABILITY otherwise applicable to this product. ECHO and its affiliated companies shall not be  
liable for any special incidental or consequential damage, including lost profits. There are no warranties extended other than as provided herein.  
This limited warranty may be modified only by ECHO.  
99922201032  
12/03/09  
Download from Www.Somanuals.com. All Manuals Search And Download.  
30  
ECHO INCORPORATED EMISSION CONTROL WARRANTY STATEMENT  
FOR ECHO AND SHINDAIWA BRANDS  
The Environmental ProtectionAgency (EPA) and the CaliforniaAir Resources Board (C.A.R.B.) and ECHO Incorporated (ECHO Inc.) are pleased  
to explain the emission control system warranty on your 2010 and later equipment/small off-road engine (SORE). New equipment/SORE must be  
designed, built and equipped to meet stringent EPA and C.A.R.B. anti-smog standards. ECHO Inc. must warrant the emission control system on  
your equipment/SORE for the periods of time listed below, provided there has been no abuse, neglect or improper maintenance of your equipment/  
SORE. Your emission control system may include parts such as: carburetor, fuel-injection system, ignition system, catalytic converter/muffler, fuel  
tank, fuel feed lines, fuel cap assembly, spark plug, air filters, and other associated components. Where a warrantable condition exists, ECHO  
Inc will repair your equipment/SORE at no cost to you including diagnosis, parts and labor. The Emission Control System warranty is extended  
to the original owner including all subsequent owners.  
MANUFACTURER'S WARRANTY COVERAGE:  
The emission control system is warranted for 2 years or the length of the ECHO Inc. warranty, whichever is longer. If any emission-related part  
on your equipment is defective, the part will be repaired or replaced by ECHO Inc. or its Authorized Service Representative.  
OWNER'S WARRANTY RESPONSIBILITIES:  
As the equipment/SORE owner, you are responsible for the performance of the required maintenance listed in your Operator's Manual. ECHO  
Inc. recommends that you retain all receipts covering maintenance on your equipment/SORE however, ECHO Inc. cannot deny warranty solely  
for the lack of receipts or for your failure to ensure the performance of all scheduled maintenance. As the equipment/SORE owner, you should be  
aware that ECHO Inc. may deny you warranty coverage if your equipment/SORE or a part has failed due to abuse, neglect, improper maintenance  
or unapproved modifications.  
You are responsible for presenting your equipment/SORE to an ECHO Inc. authorized service representative as soon as a problem exists. The  
warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days. If a warrantable condition exists and there is no  
Authorized Dealer within 100 miles, ECHO Inc. will pay to ship the unit to the nearest authorized dealer. If you have questions regarding your  
warranty coverage, you should contact ECHO Inc. at 1-800-673-1558, web site WWW.ECHO-USA.COM or contact Shindaiwa at 1-877-986-  
7783, web site WWW.SHINDAIWA.COM.  
WHAT DOES THIS WARRANTY COVER?  
ECHO Inc. warrants that your equipment/SORE was designed, built and equipped to conform with applicable EPA and C.A.R.B. emissions  
standards and that your equipment/SORE is free from defects in material and workmanship that would cause it to fail to conform with applicable  
requirements for 2 years or the length of the ECHO Inc. warranty, whichever is longer. The warranty period begins on the date the product is  
purchased by an end user.  
HOW WILL A COVERED PART BE CORRECTED?  
If there is a defect in a part covered by this warranty, any ECHO Inc. Authorized Service Dealer will correct the defect. You will not have to pay  
anything to have the part adjusted, repaired or replaced. This includes any labor and diagnosis for warranted repairs performed by the dealer. In  
addition, engine parts not expressly covered under this warranty but whose failure is a result of a failure of a covered part will be warranted.  
WHAT PARTS ARE COVERED?  
Any applicable emission related part not scheduled for "required maintenance" will be repaired or replaced within the warranty period. The repaired  
or replaced part will be warranted for the remaining ECHO Inc. warranty period.  
Any warranted part that is scheduled only for regular inspection in the written instructions supplied is warranted for the warranty period stated  
above. Any such part repaired or replaced under warranty will be warranted for the remaining ECHO Inc. warranty period.  
Any emission related part scheduled for replacement during "required maintenance" is warranted for the period of time prior to the first scheduled  
replacement point for that part. Any such part repaired or replaced under warranty shall be warranted for the remainder of the period prior to the  
first scheduled replacement point for that part.  
Any manufacturer-approved replacement part may be used in the performance of any warranty maintenance or repairs on emission related parts,  
and must be provided without charge if the part is still under warranty.  
Any replacement part that is equivalent in performance and durability may be used in non-warranty maintenance or repairs, and shall not reduce  
the warranty obligations of the manufacturer.  
Throughout the equipment/SORE warranty period, ECHO Inc. will maintain a supply of warranted parts sufficient to meet the expected demand  
for such parts.  
SPECIFIC EMISSION RELATED WARRANTED PARTS:  
• Electronic Ignition System  
• Catalytic Converter / Muffler Assembly  
• Choke  
• Spark Plug  
• Carburetor (complete assembly or replaceable components)  
• Fuel-Injection Assembly (or replaceable components)  
• Fuel Cap Assembly  
• Fuel Tank  
• Air Filter  
• Fuel Feed Line (and associated clamps/connectors as applicable)  
WHAT IS NOT COVERED?  
Any failure caused by abuse, neglect, improper maintenance, unapproved modifications, use of unapproved add-on parts/modified parts or  
unapproved accessories.  
99922201033  
01/2010  
This Emission Control Warranty is valid only for the U.S.A., it's Territories, and Canada.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
®
Sh r e d 'N'Va c  
31  
Op e r a t O r 'S Ma N u a l  
n o T e s  
Download from Www.Somanuals.com. All Manuals Search And Download.  
se r v IC In g In f o r m a T Io n  
p a r T s /s e r Ia l n u m b e r  
Genuine ECHO Parts and ECHO REPOWER™ Parts and Assemblies  
for your ECHO products are available only from an Authorized ECHO  
Dealer. When you do need to buy parts always have the Model Num-  
ber, Type and Serial Number of the unit with you. You can find these  
numbers on the engine housing. For future reference, write them in the  
space provided below.  
Model No. _________________SN. ___________________  
s e r v IC e  
Service of this product during the warranty period must be performed  
by an Authorized ECHO Service Dealer. For the name and address of  
the Authorized ECHO Service Dealer nearest you, ask your retailer or  
call: 1-800-432-ECHO (3246). Dealer information is also available on  
our Web Site. When presenting your unit for Warranty service/repairs,  
proof of purchase is required.  
DEAlER? Call  
1-800-432-ECHO  
1-800-432-3246  
or  
www.echo-usa.com  
e C h o C o n s u m e r p r o d u C T s u p p o r T  
If you require assistance or have questions concerning the applica-  
tion, operation or maintenance of this product you may call the ECHO  
Consumer Product Support Department at 1-800-673-1558 from 8:30  
am to 4:30 pm (Central Standard Time) Monday through Friday. Before  
calling, please know the model and serial number of your unit.  
CONSUMER PRODUCT  
SUPPORT  
1-800-673-1558  
8:30 - 4:30 Mon - Fri C.S.T.  
w a r r a n T y r e g Is T r a T Io n  
To ensure trouble free warranty coverage it is important that you regis-  
out the warranty registration card supplied with your unit. Registering  
your product confirms your warranty coverage and provides a direct  
link between you and ECHO if we find it necessary to contact you.  
a d d IT Io n a l o r r e p l a C e m e n T m a n u a l s  
Replacement Operator, Safety Manuals, and Parts Catalogs are available from your ECHO dealer or at www.echo-  
usa.com or by contacting ECHO Inc., 400 Oakwood Road, Lake Zurich, IL 60047 (800-673-1558). Always check the  
ECHO Web Site for updated information.  
Safety Videos are available from your Echo dealer. A $5.00 shipping charge will be required for each video.  
ECHO, iNCORPORATED  
400 Oa k w O O d RO a d  
la k e Zu r IC h , Il 60047-1564  
P07213001001/P07213999999  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Eiki CRT Television LC XB33N User Manual
Eiki CRT Television LC XWP2000 User Manual
Electro Voice Portable Speaker Royal 400 User Manual
ETA Systems Power Supply PD10VRS User Manual
Extron electronic Stereo Amplifier DVI DA4 User Manual
Fujitsu Recording Equipment MB15E07SL User Manual
GarrettCom Switch Magnum 3000 User Manual
GE Cordless Telephone 25912 User Manual
GE Dishwasher GHDA690P User Manual
GMC Automobile X2208 User Manual