®
4x1 DVI DL Switcher
EXT-DVI-441DL
User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
1
Introduction
2
Operation Notes
Features
3
4
Panel Layout
Panel Descriptions
5
6
Connecting and Operating The 4x1 DVI DL Switcher
RMT-4IR Remote Control Description
4x1 DVI DL Switcher Remote Installation
4x1 Remote and Switcher Configuration
EDID Modes
7
8
9
10
12
13
14
14
20
22
23
24
DL (Dual Link) Only Modes
RS-232 Serial Control
RS-232 Serial Control Commands
EDID Management
Routing Commands
Rack Mount Installation
Specifications
Warranty
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Congratulations on your purchase of the 4x1 DVI DL Switcher. Your complete
satisfaction is very important to us.
Gefen
Gefen delivers innovative, progressive computer and electronics add-on solutions
that harness integration, extension, distribution and conversion technologies.
Gefen’s reliable, plug-and-play products supplement cross-platform computer
systems, professional audio/video environments and HDTV systems of all sizes
with hard-working solutions that are easy to implement and simple to operate.
The Gefen 4x1 DVI DL Switcher
The rack-mountable Gefen 4x1 DVI DL Switcher offers an economical solution by
eliminating the need to purchase many displays for each DVI source in a studio
or lab situation. A plug-and-play solution, the 4x1 DVI DL Switcher shares one
dual-link display with up to four computers or other DVI video sources, saving
space on your desktop. The source computer is selected using the included IR
remote control or through RS-232 control.
How It Works
The DVI monitor is connected to the switcher’s output. Up to four DVI sources
connect to the switcher’s DVI inputs using included high quality DVI cables.
The included power supply is connected to the switcher via the locking power
plug and then to a power outlet. The currently selected computer’s video signal
appears on the shared monitor. Video sources are selected/switched using the
RMT-4IR remote control, RS-232 control, or the input selector push button on the
front panel of the switcher.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION NOTES
READ THESE NOTES BEFORE INSTALLING OR
OPERATING THE GEFEN 4X1 DVI DL SWITCHER
•
The 4x1 DVI DL Switcher will take any of up to four (4) DVI dual-link or
single-link resolution inputs and switch them, one at a time, to a DVI output
device such as a display/monitor or projector. Resolutions can be up to
3840x2400.
•
•
The 4x1 DVI DL Switcher is housed in a metal box for better RF shielding.
By default, the EDID of the attached display is copied to all the local inputs.
Make sure that the display is connected to the switcher before applying
power.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
Features
•
•
•
•
Switches easily between any four DVI-SL or DVI DL sources
Maintains highest resolution dual link DVI
Supports resolutions up through 3840x2400
EDID Storage and programming for best source/display compatibility
•
•
•
•
•
Extends the range of the video signal on the DVI outputs up to 50 feet
Discrete IR remote control included
Serial RS-232 port for switching input sources via automated control or PC
Supports DDWG standards for DVI monitors
Rack ears included
Package Includes
(1) 4x1 DVI DL Switcher
(4) 6-ft Dual Link DVI cables (M-M)
(1) 5V DC Power Supply
(1) User’s Manual
(1) IR remote control
(1) Set of Rack Ears
3
Download from Www.Somanuals.com. All Manuals Search And Download.
PANEL LAYOUT
Front Panel
4
5
1
2
3
Back Panel
9
8
6
7
4
Download from Www.Somanuals.com. All Manuals Search And Download.
PANEL DESCRIPTIONS
1
2
3
4
5
6
External IR Port
For connection of external IR extension device such as the Gefen IR Extender
(part # EXT-RMT-EXTIR).
IR Receiver
Receives IR signal from the handheld Infrared remote control unit included with
the product.
DVI Signal Status LEDs 1-4
Provide visual confirmation of the currently selected DVI input signal out of the
four DVI input ports.
DVI Input Selector
Push-button switch cycles the next DVI input 1-4 in a forward sequence starting
again at 1.
Power Indicator LED
Indicates when the 4x1 DVI DL Switcher is receiving 5V DC power from its
included AC power supply.
5V Locking Power Receptacle
Supplies power to the 4x1 DVI DL Switcher from the included external 5V DC
power supply. The 5V power supply has a locking power tip which screws into
this receptacle.
7
8
9
DVI Input Ports 1-4
DVI video sources one through four attach to the 4x1 DVI DL Switcher.
DVI Output Port
This DVI output port is connected to the display device (Monitor, Projector).
RS-232 Serial Communications Interface
Provided for external control of the 4x1 DVI DL Switcher.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING AND OPERATING THE 4X1 DVI DL SWITCHER
How to Connect the 4x1 DVI DL Switcher to your devices:
1. Connect user supplied DVI cables from the DVI sources into the 4x1 DVI
Switcher’s Inputs.
2. Connect the cable from your display (monitor or projector) into the DVI Out
of the 4x1 DVI DL Switcher.
3. Connect the 5V power supply, then plug it into the wall. Turn on the DVI
display or projector first, then the video sources (computers). Turn on
the 4x1 DVI DL Switcher by screwing its 5V DC power supply tip into the
receptacle in the rear of the chassis.
Note: The Switcher retrieves device resolution and video timing capability
information called EDID from the display and feeds it to all connected input
sources. This mode of operation is called LOCAL EDID mode. It allows
a much faster setup time and improved operational stability since input
sources do not need to individually collect and store EDID on their own.
If some sources do not display correctly, you can individually configure each
input source and/or program custom EDIDs (such as standard compatible
resolutions) into the Switcher, or alternately set each input source to directly
read EDID from the display device (with the Local EDID Mode turned OFF).
These procedures are covered in detail on pages 10-11 along with EDID
concepts in general.
Wiring Diagram for the 4x1 DVI DL Switcher
DUAL LINK DVI CABLE
Computer
Computer
Computer
Switcher
Computer
Dual Link DVI Display
EXT-DVI-441DL
6
Download from Www.Somanuals.com. All Manuals Search And Download.
4X1 DVI DL SWITCHER REMOTE DESCRIPTION
LED Indicator
Input Selection
Buttons
The RMT-4IR remote control will allow the user to select which of 4 DVI sources will
be displayed. Please use the information below when selecting the desired source
for output to a display or other DVI video receiving device.
RMT-4IR Button
DVI Source
1
2
3
4
1
2
3
4
7
Download from Www.Somanuals.com. All Manuals Search And Download.
4X1 DVI DL SWITCHER REMOTE INSTALLATION
To use the RMT-4IR remote, remove the battery cover on the back of the remote to
reveal the battery compartment. Insert the included battery into the open battery slot.
The positive (+) side should be facing up. Ensure that both DIP (Dual Inline Package)
switches are in the OFF position. Replace the battery cover. The remote ships with 2
batteries. One battery is needed for operation and the other battery is complimentary.
Empty Battery Slot
IR Code Dip Switches
8
Download from Www.Somanuals.com. All Manuals Search And Download.
4X1 REMOTE CONTROL AND SWITCHER CONFIGURATION
How to Resolve IR Code Conflicts
In the event that IR commands from other remote controls conflict with the
supplied RMT-4IR remote control, changing the remote control channel will
alleviate this issue. The RMT-4IR remote control and the 4x1 DVI DL Switcher
both have banks of DIP (Dual Inline Package) Switches for configuring the
remote channel that the units use to communicate. These settings must exactly
match each other for proper operation.
The DIP Switch bank on the RMT-4IR is located underneath the battery cover.
DIP Switch banks for the 4x1 DVI DL Switcher are located on the underside of
the unit beneath a black piece of metallic tape. One DIP switch bank (4-switch)
is for the adjustment of remote control frequencies and switch behavior. The
other DIP switch (8-switch) is reserved for Gefen use only. DIP Switches 1 and 2
on the RMT-4IR directly correspond to DIP Switches 1 and 2 on the 4x1 DVI DL
Switcher. Only switches 1 and 2 (of 4 in that bank) are used for IR Code settings.
Remote Channel 1:
Default
Remote Channel 2:
Remote Channel 4:
1
1
2
2
1
1
2
2
Remote Channel 3:
Left: Picture of the opened rear battery
compartment of the RMT4-IR remote showing
the exposed DIP Switch bank between the
battery chambers.
4x1 DVI DL Switcher
Remote Channel 1:
Default
Remote Channel 2:
1
1
3
3
2
2
4
4
1
1
3
3
2
2
4
Remote Channel 3:
Remote Channel 4:
4
9
Download from Www.Somanuals.com. All Manuals Search And Download.
EDID MODES
What is EDID and what is it used for?
Under normal circumstances, an audio/video source device (digital or analog) will
require information about a connected device/display to assess what resolutions
and features (capabilities) are possible. The source device can then tailor its
output to create resolutions and/or features that are compatible with the attached
device/display. This capability information is called EDID (Extended Display
Identification Data). A source device can only accept and read one EDID data
structure/record from a connected source device/display. Likewise, the source
device can output only one video resolution to a connected device/display.
The importance of EDID with regards to the 4x1 DVI DL Switcher
The 4x1 DVI DL/SL Switcher handles multiple sources/inputs. Each connected
source device must correctly read one EDID data structure in order to address its
display device correctly. EDID management is carefully handled by the 4x1 DVI
DL Switcher to insure that EDID is recorded and retransmitted properly, otherwise
display of the input sources might not occur correctly (or at all).
Managing EDID with the 4x1 DVI DL Switcher
The 4x1 DVI DL Switcher uses 2 modes for routing EDID. They are:
1. When the local EDID Mode is ON, (factory default setting) the Switcher
copies the EDID of the connected display to the local memory location as
they are selected. Each device must fully “boot up” before you can select the
next input. The connected device derives EDID information from the local
memory location.
2. When the local EDID Mode is OFF, each time a new source device is
selected, the Switcher connects EDID from the attached display to the
currently selected input source.
Both modes are described in greater detail on the opposite page.
NOTE: The 4x1 DVI DL Switcher also features an EDID Lock Mode, allowing
the EDID to be stored. See the following page for details.
How do I change EDID modes in the 4x1 DVI DL Switcher?
There is a bank of 4 DIP (Dual Inline Package) switches located on the main
circuit board of the Switcher underneath a small piece of silver grey tape on the
underside of the Switcher. When the sticker is removed, there will be two DIP
switch banks visible, one with 4 switches and one with 8 switches. The 8-switch
DIP switch bank is not used here (it is used for the DL (dual link) feature covered
later on page 12.)
10
Download from Www.Somanuals.com. All Manuals Search And Download.
EDID MODES
EDID Modes
The diagram below illustrates the 4-position DIP switch bank (containing 4 small
white toggle switches as shown). The functions of the switches are as follows:
DIP SWITCH
Function
IR Channel
1
2
3
4
IR Channel
EDID Mode
1
3
2
4
EDID Lock Mode
Use DIP switch 3 to set the desired EDID mode. (UP is On)
How to set the two EDID Modes:
1. Local EDID Mode ON (Switch 3 = OFF, FACTORY DEFAULT SETTING)
•
During power-on, the connected display’s EDID is copied to all four local
EDID storage locations at once. EDID stored in local memory is then
passed to all input sources.
•
The EDID stored in the local locations can be overwritten with another
EDID from the following locations:
•
•
Built-in EDID memory bank (up to 7 EDID records can be stored)
EDID collected directly from the input display upon power-up.
2. Local EDID Mode OFF (Switch 3 = ON)
•
The DDC signal of the connected display is routed directly to each input
source. Each time a new source device is selected, EDID is transmitted
from the attached display to the currently selected input source. (This
mode will successfully pass HDCP signals.)
3. EDID Lock Mode (DIP Switch 4 = ON)
•
Locks the last stored EDID, even if the unit is power-cycled. To store a
new EDID, do the following:
1. Power-down the Switcher and set DIP Switch 4 to the OFF position.
2. Connect the display to the DVI output port then power-on the Switcher.
3. Set DIP Switch 4 to the ON position to lock the EDID.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
DL (DUAL LINK) ONLY MODES
DL (Dual Link) Only Modes
The 8-position DIP switch bank located on the underside of the 4x1 DVI DL
Switcher can be used to set each individual input to work in a Dual Link Only
mode. These modes should only be enabled if issues occur when using Dual
Link sources and displays in the default mode.
DIP SWITCH
Function
DIP SWITCH
Function
N/A
1
2
3
4
Input 1 Mode
Input 2 Mode
Input 3 Mode
Input 4 Mode
5
6
7
8
N/A
N/A
N/A
DL (Dual Link) and SL (Single Link) Mode (Switch=OFF) DEFAULT
•
This setting can be set individually for each input. This mode will allow
the connection of both Dual Link and Single Link displays.
DL (Dual Link) Only Mode (Switch=ON)
•
This setting can be set individually for each input. This mode should be
enabled if issues with the default occur with Dual Link displays.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
RS-232 SERIAL CONTROL INTERFACE
What features are available via the RS-232 serial communications port?
The 4x1 DVI DL Switcher can accept commands through the RS-232 serial
communications port located on the rear panel. The current RS-232 control
features are the ability to switch/route inputs to outputs without the RMT-4IR
remote control.
How do I use these features?
These features were initially intended for utilization by custom installers in
automated setups. However, these features can be tested by using any Windows
PC with a terminal emulation program. The next few pages will show you how.
What pins are used for communication with the 4x1 DVI DL Switcher?
Only pins 2 (Receive), 3 (Transmit), and 5 (Ground) are used for communication.
A null-modem adapter should not be used with this Switcher.
5 4 3 2 1
1 2 3 4 5
9 8 7 6
6 7 8 9
Only Pins 2 (RX), 3 (TX), and 5 (Ground) are used on the RS-232 serial interface
What are the RS-232 communications port settings?
Bits per second ............................................................................................ 19200
Data bits ............................................................................................................... 8
Parity ............................................................................................................. None
Stop bits ................................................................................................................1
Flow Control .................................................................................................. None
13
Download from Www.Somanuals.com. All Manuals Search And Download.
RS-232 SERIAL CONTROL COMMANDS
RS-232 Features
RS-232 remote functions are used to control of this product’s features. Features
include input to output routing, EDID storage, EDID management, etc.
Functions Syntax
The syntax for each function is always the same:
#Character as the start flag → Function name → Space ( _ ) as function name
end flag → Parameter 1 → Space → Parameter n → Carriage Return ( \r ) →
Sample:
#FunctionName_param1_param2_param3_param4...\r
Syntax is NOT case sensitive.
EDID Management
Function
Description
#EDIDDSTOLO Read downstream EDID and stores into all inputs
#EDIDDSTOBA Read downstream EDID and stores in EDID Bank
#EDIDBATOLO Read from EDID bank and store into all local inputs
#DDCTODS
#DDCTOLO
#DEF
Route input DDC to downstream EDID (pass-through mode)
Routes input DDC to local EDID
Sets unit to default factory settings
#LOEDIDTOBA Load EDID from serial port and store in EDID bank
#LOEDIDTOLO Loads EDID from serial port and store in any input
#PRBAEDID
#PRDSEDID
#PRLOEDID
Reads EDID from EDID bank and sends to serial port
Reads downstream EDID and sends it to serial port
Reads local input EDID and sends it to serial port
14
Download from Www.Somanuals.com. All Manuals Search And Download.
RS-232 SERIAL CONTROL COMMANDS
#EDIDDSTOLO Function
The #EDIDDSTOLO function reads the downstream EDID and stores into all lo-
cal inputs.
Syntax:
#EDIDDSTOLO
Parameters:
None
#EDIDDSTOBA Function
The #EDIDDSTOBA function reads the downstream EDID and stores it to a
specified EDID bank.
Syntax:
#EDIDDSTOBA param1
Parameters:
param1
EDID bank offset
[1 - 7]
#EDIDBATOLO Function
The #EDIDBATOLO function reads an EDID from an EDID bank and stores it in
all inputs.
Syntax:
#EDIDBATOLO param1
Parameters:
param1
EDID bank offset
[1 - 7]
15
Download from Www.Somanuals.com. All Manuals Search And Download.
RS-232 SERIAL CONTROL COMMANDS
#DDCTODS Function
The #DDCTODS function routes the input DDC to the downstream EDID (pass-
through mode).
Syntax:
#DDCTODS
Parameters:
None
#DDCTOLO Function
The #DDCTOLO function routes the input DDC to the local EDID.
Syntax:
#DDCTOLO
Parameters:
None
#DEF Function
The #DEF function set the Switcher to the factory default settings.
Syntax:
#DEF
Parameters:
None
16
Download from Www.Somanuals.com. All Manuals Search And Download.
RS-232 SERIAL CONTROL COMMANDS
#LOEDIDTOBA Function
The #LOEDIDTOBA function loads the specified EDID file and stores it in a
specified EDID bank.
Syntax:
#LOEDIDTOBA param1 param2 param3
Parameters:
param1
Echo mode
[0 - 1]
Value
Meaning
0
1
Semi echo mode
Full echo mode
param2
param3
EDID size
[1 - 2]
Value
Meaning
1
2
128 byte EDID
256 byte EDID
EDID bank offset
[1 - 7]
17
Download from Www.Somanuals.com. All Manuals Search And Download.
RS-232 SERIAL CONTROL COMMANDS
#LOEDIDTOLO Function
The #LOEDIDTOLO function loads the specified EDID file to a specified local
input.
Syntax:
#LOEDIDTOLO param1 param2
Parameters:
param1
param2
Echo mode
[0 - 1]
Value
Meaning
0
1
Semi echo mode
Full echo mode
EDID size
[1 - 2]
Value
Meaning
1
2
128 byte EDID
256 byte EDID
#PRBAEDID Function
The #PRBAEDID function reads the EDID file from the specified bank and sends
it to the serial port.
Syntax:
#PRBAEDID param1 param2
Parameters:
param1
param2
EDID bank offset
File type
[1 - 7]
[0 - 1]
Value
Meaning
.BIN file
.TXT file
0
1
18
Download from Www.Somanuals.com. All Manuals Search And Download.
RS-232 SERIAL CONTROL COMMANDS
#PRDSEDID Function
The #PRDSEDID function reads the downstream EDID and sends it to the serial
port.
Syntax:
#PRDSEDID param1
Parameters:
param1
File type
[0 - 1]
Value
Meaning
.BIN file
.TXT file
0
1
#PRLOEDID Function
The #PRLOEDID function reads the local EDID and spools it to the serial port.
Syntax:
#PRLOEDID param1
Parameters:
param1
File type
[0 - 1]
Value
Meaning
.BIN file
.TXT file
0
1
19
Download from Www.Somanuals.com. All Manuals Search And Download.
RS-232 SERIAL CONTROL COMMANDS
Commands
Simplified syntax was used for command implementation for faster operation with
the device: # character – isn’t needed, the command name is reduced to 1 letter.
The commands are not case-sensitive.
Command
Description
P
1
2
3
4
Displays the function menu
Switch to Input 1
Switch to Input 2
Switch to Input 3
Switch to Input 4
The ASCII character table below indicates which Switcher input will be routed to
the output Display when the corresponding ASCII (numeric) character is typed.
ASCII
Input
Binary
1
2
3
4
1
2
3
4
0011 0001
0011 0010
0011 0011
0011 0100
20
Download from Www.Somanuals.com. All Manuals Search And Download.
RS-232 SERIAL CONTROL COMMANDS
2. USING SHORT-CUT CHARACTERS TO CHANGE SETTINGS
2.1 HYPERTERMINALtm SETTINGS in Microsoft Windowstm
First, please setup correct communications by performing these commands (as
shown on the screen shot immediately below):
File->Properties->Setting->ASCII Setup
Also, please be sure to unmark the check box that says “Send line ends with line
feeds.”
2.2 EXAMPLE -- CHANGE THE ROUTED SOURCE
Now you are ready to route Display input sources.
At the Hyperterminal cursor prompt, type the numeral key of the input to switch
to, followed by the ENTER key.
Wait until you see the message “Function Done” on the Display. At this point the
Display should show the correct Source corresponding to the numeral that was
typed.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
RACK MOUNT INSTALLATION
Rack mount ears are provided for installation of this unit into a 1U rack mount
space.
1. Locate the side screws on the unit.
2. Remove the front 2 screws that are located closest to the front of the unit.
3. Using the removed screws, screw the rack mounting bracket into the unit.
4. Repeat the procedure on the opposite side of the unit.
1
Front of unit
Rear of unit
2
3
4
22
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
Video Amplifier Bandwidth:..................................................................2 x 165 MHz
Input Video Signal:...............................................................................1.2 Volts p-p
Input DDC Signal:..........................................................................5 Volts p-p (TTL)
Single Link Max. Resolution:................................................................1920 x 1200
Dual Link Max. Resolution:.................................................................. 3840 x 2400
DVI Connector:.................................................... DVI-I 29-pin female (digital only)
Power Supply:...............................................................................................5V DC
Power Consumption:.............................................5 Watts (min.) / 25 Watts (max.)
Dimensions:.....................................................................17.1” W x 1.8” H x 4.4” D
Rackmountable:..............................................................................1U Rack Space
Shipping Weight:...........................................................................................12 lbs.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY
Gefen warrants the equipment it manufactures to be free from defects in material
and workmanship.
If equipment fails because of such defects and Gefen is notified within two (2)
years from the date of shipment, Gefen will, at its option, repair or replace the
equipment, provided that the equipment has not been subjected to mechanical,
electrical, or other abuse or modifications. Equipment that fails under conditions
other than those covered will be repaired at the current price of parts and labor in
effect at the time of repair. Such repairs are warranted for ninety (90) days from
the day of reshipment to the Buyer.
This warranty is in lieu of all other warranties expressed or implied, including
without limitation, any implied warranty or merchantability or fitness for any
particular purpose, all of which are expressly disclaimed.
1. Proof of sale may be required in order to claim warranty.
2. Customers outside the US are responsible for shipping charges to and from
Gefen.
3. Copper cables are limited to a 30 day warranty and cables must be in their
original condition.
The information in this manual has been carefully checked and is believed to
be accurate. However, Gefen assumes no responsibility for any inaccuracies
that may be contained in this manual. In no event will Gefen be liable for
direct, indirect, special, incidental, or consequential damages resulting from
any defect or omission in this manual, even if advised of the possibility of such
damages. The technical information contained herein regarding the features and
specifications is subject to change without notice.
For the latest warranty coverage information, refer to the Warranty and Return
PRODUCT REGISTRATION
Please register your product online by visiting the Register Product page
under the Support section of the Gefen Web site.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
25
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
26
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
Download from Www.Somanuals.com. All Manuals Search And Download.
Rev A10
20600 Nordhoff St., Chatsworth CA 91311
1-800-545-6900 818-772-9100 fax: 818-772-9120
Pb
This product uses UL listed power supplies.
Download from Www.Somanuals.com. All Manuals Search And Download.
|