GE Monogram Headphones 86710 User Manual

5. Initiate the device discovery feature on the mobile phone.  
Refer to the mobile phone user guide for instructions on  
initiating this feature.  
MUTING THE HEADSET  
You can mute and un-mute the microphone temporarily so  
that you cannot be heard by the connected party.  
6. When prompted by the mobile phone, enter the headset  
passkey or PIN code 0000. When pairing is complete, the Blue  
LED on headset will flash at three second intervals and the  
headset will be placed  
To mute the headset – While on a call, press and hold the  
Volume UP button “+” and the Volume DOWN button “-”  
concurrently more than 3 seconds, and you will hear a MUTE  
tone (Single beep), the microphone is muted.  
Bluetooth® Headset  
GE Model 86710  
If disconnection or a lost link occurs, it may be due to  
the following reasons:  
a) The range is over 33 feet between the headset and  
the mobile phone.  
To un-mute the headset - When microphone is muted, press  
and hold Volume UP “+”button and Volume DOWN “-” button  
concurrently for 3 seconds, and you will hear a MUTE tone  
(Single beep), the microphone is un-muted.  
User Guide  
b) The mobile phone disconnected the link to conserve  
power or enable another function.  
VOICE DIALING  
With the headset in standby mode, press and release (click)  
the Talk button on the Headset, and you will hear the “Voice  
Dial” tone (Two short beeps). Speak the name of the person  
you wish to call. The call is automatically connected to your  
headset.  
c) Either device has been switched off.  
Note: The headset, in normal operation, should maintain the  
connection with the mobile phone at all times once pairing  
has been successful and a connection has been established  
between the two devices.  
LAST NUMBER REDIAL  
Whilst in standby mode, press and hold the Volume UP “+”  
button for more than 3 seconds, and you will hear a “Last  
Number Redial” tone (single long beep); Release the Volume  
UP “+” button, the call is automatically connected to your  
mobile phone.  
To cancel pairing mode - While the headset is in pairing  
mode, you can cancel the pairing process and turn off the  
headset. Press and hold the Talk button for approx 3 seconds.  
You will hear an “OFF” tone (two descending “beeps”) and the  
Blue LED will flash quickly several times. Release the  
Talk button.  
Battery Chamber  
Cover  
Ear Hook  
Talk Button  
VISUAL INDICATORS  
The Blue and Amber LEDs will flash when certain operations  
(Turn on/off headset, enter pairing mode, and finish pairing  
mode) are initiated. They can also indicate the status of the  
headset:  
Volume  
UP  
Battery  
Cover  
Lock  
FITTING THE HEADSET ON YOUR EAR  
The AAA Headset is designed to fit comfortably in your ear.  
The ear hook can be fixed into the headset from both sides,  
allowing you to position on right or left ear. The ear hook can  
be separated from the Headset by simply pulling the base of  
the hook away from the main body of the Headset.  
Amber  
LED  
Status  
Indication  
Headset off  
All LEDs are off  
Microphone  
Headset in standby  
mode; ready to make  
or receive calls  
The ear hook can then be reinserted in the other direction for  
positioning on the opposite ear. The ear hook is flexible and  
can be bent to adjust the fit that is best for the individual user.  
Volume  
DOWN  
Blue LED flashes at 3 second intervals  
Headset in pairing mode Blue and amber LEDs flash alternately  
Blue LED  
To replace the ear cap - Stretch the rubber ear cap around  
the end of the speaker until secure.  
Headset making  
connection, audio  
connection for voice dial  
Blue LED flashes twice quickly at  
1 second intervals  
To place the headset on your ear - Place the headset  
speaker in your ear with the microphone angled towards  
your mouth. The headset should fit snugly in your ear.  
GETTING STARTED  
TROUBLE SHOOTING  
Remove all components from the package. Items in the pack  
include: AAA Bluetooth headset with Ear Hook, Ear Cap, User  
Guide. Please check the contents carefully and contact your  
local dealer immediately if there are any shortages.  
Please note that you should also be familiar with the  
operation of your mobile phone and how to connect to  
Bluetooth devices. Please read your mobile phone user guide  
carefully. Please note that the Bluetooth headset will only  
work with Bluetooth mobile phones. For operation with a PC  
or laptop device please note that these devices should also  
be Bluetooth enabled with appropriate third party software in  
order to enable correct operation.  
SWITCHING ON YOUR HEADSET  
To turn on the headset - With the headset turned off, press  
and hold the Talk button for about 3 seconds until you hear  
the “ON” tone (two ascending “beeps”) or you see the Blue  
LED start to flash. Release the Talk button. The headset turns  
on and is placed in standby mode, ready to make and receive  
calls. After turning on the headset, the headset will try to  
connect to the last paired/connected device automatically.  
GETTING TO KNOW YOUR HEADSET  
See image above. Please note some models of headset will  
differ slightly in style, color and the functionality may vary  
according to their specifications  
INSERT THE AAA BATTERY TO YOUR HEADSET  
The headset is powered by one AAA alkaline battery. Please  
insert a AAA alkaline battery before use. A new AAA battery  
will provide up to 20 hours of talk time and up to 30 days of  
standby time.  
Symptom/Problem  
Solution  
To turn off the headset - With the headset turned on, press  
and hold the Talk button for approx 3 seconds. You will hear  
an “OFF” tone (two descending “beeps”) and the Blue LED will  
flash quickly several times. Release the Talk button.  
When talk button is pressed,  
no LEDs are on or flashing  
• Check battery power  
• Consult authorized dealer  
Headset powers on with  
blue LED flashing but no  
connection to mobile phone  
• Check unit is paired to phone.  
Check settings in phone.  
Headset default name is BTHS.  
• Check phone is switched on  
• Check handsfree settings for  
phone  
MAKING CALLS  
Please note the talk time and standby time figures are  
best estimates only. Quoted figures will vary depending  
on usage patterns, connecting device (including mobile  
phone) and AAA battery specifications. We recommend  
using a high capacity AAA battery (alkaline, rechargeable  
NiMH or Lithium) for optimum performance. Rechargeable  
NiMH and lithium batteries may provide the lowest long  
term cost, despite higher initial costs.  
You can make calls from your mobile phone, or directly from  
the headset using voice dialing commands (if this feature is  
supported by your mobile phone).  
• Ensure headset & phone are  
within range  
To make calls from your mobile phone - Dial the call from  
your mobile phone. Dependent on your mobile phone  
settings the call is automatically connected to your headset.  
CUSTOMER SERVICE INFORMATION  
In addition to the troubleshooting table on this page you can  
email help at: [email protected] or call 800 654-  
8483. For other Bluetooth products or support, please view  
To make calls using VOICE DIALING (if supported by your  
mobile phone) - Click the Talk button on your headset. You  
will hear a Voice Dial tone possibly followed by the voice-dial  
prompt tone from your mobile phone. Speak the name of the  
person you wish to call. The call is automatically connected  
to your headset.  
To insert AAA battery  
1. Unlock the battery chamber  
cover by sliding the lock towards  
the Volume DOWN ‘–‘ button.  
90-Day Limited Warranty  
Jasco Products Company warrants this product to be free  
from manufacturing defects for a period of ninety days  
from the original date of consumer purchase. This warranty  
is limited to the repair or replacement of the product  
only and does not extend to consequential or incidental  
damage to other products that may be used with this unit.  
This warranty is in lieu of all other warranties express or  
implied. Some states do not allow limitations on how long an  
implied warranty lasts or permit the exclusion or limitation  
of incidental or consequential damages, so the above  
limitations may not apply to you. This warranty gives you  
specific rights, and you may also have other rights which vary  
from state to state. If unit should prove defective within the  
warranty period, return prepaid with dated proof of purchase  
to: Jasco Products Company,  
2. Open the battery chamber by  
UNLOCK  
To make calls using LAST NUMBER REDIAL (if supported by  
your mobile phone) - While in standby mode, press and hold  
the Volume UP “+” button for about 3 seconds, and you will  
hear a “Last Number Redial” tone (single beep); Release the  
Volume UP “+” button, the call is automatically connected to  
your mobile phone.  
sliding off the cover away from  
the ear piece in the direction of  
the arrow.  
3. Insert the AAA battery making  
sure the Positive (+) end is facing  
out of the chamber and hence touching the battery cover.  
RECEIVING CALLS  
4. Use the battery cover to push the battery down and slide  
the battery chamber cover back into place and lock.  
You must configure your mobile phone to answer calls  
directly on your Bluetooth headset. Refer to the mobile phone  
user guide for instructions on initiating this feature.  
PAIRING THE HEADSET WITH YOUR MOBILE PHONE  
Pairing is the process of linking the headset with your  
Bluetooth mobile phone. Before you use the AAA headset  
with your mobile phone you must pair them. After this  
process is completed, you can use the headset only with its  
paired mobile phone. If you wish to use the headset with a  
different mobile phone, you must repeat the pairing process  
with the new mobile phone. In this case, the headset will no  
longer work with the original mobile phone.  
When you hear your headset ring, click the Talk button on  
the headset. The call is automatically connected to your  
headset. Please note you can also Reject calls by depressing  
the talk button for about 3 seconds. (Not all phones support  
this feature)  
311 N.W. 122nd St., Oklahoma City, OK 73114  
DISCLAIMER  
ENDING CALLS  
When you have finished your call, press the Talk button on  
your headset. The call will be disconnected  
While every effort has been made to ensure that the  
information in this manual is accurate and complete, no  
liability will be accepted for any errors and/or omissions  
made. The manufacturer reserves the right to make changes  
and improvements to the specifications and features of  
the hardware and firmware of the products described in  
this document without prior notice. Reproduction, transfer,  
distribution or storage of part or all of the contents in this  
document in any form is prohibited without prior permission  
of the manufacturer. All trademarks acknowledged. The  
product is Bluetooth qualified by Nolan Systems.  
Please refer to the user manual of your mobile phone for  
further information on ‘How to Pair’. Typically, you need  
to make your phone ‘Discover’ the headset by using a  
“Bluetooth”, “Connect” or “Setup” menu then selecting an  
option to “Discover” other Bluetooth devices.  
TRANSFERRING CALLS  
You can transfer calls connected to your headset back  
to your mobile phone, or from your mobile phone to your  
headset. (Not all phones support this feature)  
To transfer calls from your headset to the phone or from the  
phone to the Headset press the Volume UP “+” button for  
more than 3 seconds until you hear a tone. The audio will be  
transferred.  
To pair the devices  
1. Before you pair the headset, ensure that the battery is  
fully charged.  
2. Set up your mobile phone to “Discover” your headset.  
ADJUSTING THE VOLUME  
To increase the volume - While on a call, press and release  
(click) the Volume UP button “+” to increase volume by 1 step.  
Repeat this procedure until you have reached the desired level.  
3. With the headset turned off, press and hold the Talk button  
for about 7 seconds until the blue and amber LEDs flash  
alternately or until you will hear the “PAIR” tone (the second  
of two tones)..  
To decrease the volume - While on a call, press and release  
(click) the Volume DOWN button “-“ to decrease volume by  
1 step. Repeat this procedure until you have reached the  
desired level.  
4. Release the Talk button. The headset is now in “Pairing”  
Mode.  
86710-2 vers. 2 7/06  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Conair Food Processor NE4 User Manual
CP TECHNOLOGIES Security Camera FCS 6010 User Manual
Digital Media Switch 900TL User Manual
Dukane Tablet MCC2 User Manual
DXG Technology Digital Camera DXG 518 User Manual
Edelbrock Automobile Parts 1926 User Manual
Electro Voice Music Mixer BK 1632 User Manual
Freecom Technologies Computer Drive Hard Drive Dock User Manual
GE Monogram Gas Grill ZGG48L31CSS User Manual
GE VCR VGN550 User Manual