TWISTER
2700XV
Original Instructions
For all customer enquiries or for replacement parts, contact:-
¤ 01325 300303
customer.services@husqvarna.co.uk
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Do not use the product if the electric cables are dam-
aged or worn.
condition before use.
Use
4. Immediately disconnect from the mains electricity supply if
the cable is cut, or the insulation is damaged. Do not touch
the electric cable until the electrical supply has been dis-
connected. Do not repair a cut or damaged cable. Re-
place it with a new one.
1. Use the product only in daylight or good artificial light.
2. Do not use the product when it is raining or in damp
and wet areas.
3. Never use the product in or near water or ponds.
4. Know how to stop the product quickly in an emergency.
5. On slopes, be extra careful of your footing and wear
non-slip footwear.
5. Your electric cable must be uncoiled, coiled cables can
overheat and reduce the efficiency of the product.
6. Do not pull cable around sharp objects.
7. Always switch off at the mains before disconnecting any
plug, cable connector or extension cable.
6. Do not walk backwards whilst operating your prod-
uct, you could trip. Walk, never run.
7. Always direct the cable to the rear, away from the product.
8. Keep children, pets and bystanders at a safe dis-
tance when using your product.
8. Switch off, remove plug from mains and examine
electric supply cable for damage or ageing before
winding cable for storage. Do not repair a damaged
cable, replace it with a new one. Use only genuine
replacement cable.
9. Keep long hair away from air inlet.
10.Keep all inlets clear of debris.
11.Always remain alert.
9. Never carry the product by the cable.
10.Never pull on the cable to disconnect any of the plugs
11.Always wind cable carefully, avoiding kinking.
12.Use only on AC mains supply voltage shown on the
product rating label.
12.Do not attempt to use your product without the fully
assembled debris bag fitted.
13.Never blow debris in the direction of bystanders.
14.Do not overreach. Keep proper footing and balance
at all times.
13.Our products are double insulated to EN60335.
Under no circumstance should an earth be con-
nected to any part of the product.
15.The impeller continues to rotate after your product
has been switched off.
16.Remove the plug from the mains :-
Preparation
-
before removing or replacing fully assembled debris
bag;
1. While using your product always wear substantial
footwear and long trousers.
-
-
-
-
before leaving the product unattended for any period;
before clearing a blockage;
2. The use of eye protection is recommended.
3. The use of ear protection is recommended.
4. To prevent dust irritation, the wearing of a face mask
is recommended.
before checking, cleaning or working on the product;
if the product starts to vibrate abnormally. Check im-
mediately. Excessive vibration can cause injury.
Maintenance and storage
5. Do not wear loose clothing or jewellery that can be
drawn into the air inlet.
1. Keep all nuts, bolts and screws tight to be sure the
6. Do not wear clothing with attachments, i.e. toggles or
drawstrings that can be drawn into the air inlet.
7. Inspect your product before each use.
8. Do not use if any part is damaged or broken or if any
of the screws are loose. Have it repaired by an au-
thorised repairer.
product is in a safe working condition.
2. Replace worn or damaged parts for safety.
3. Use only genuine replacement parts and accessories
4. Inspect the debris bag regularly. If the debris bag be-
comes worn or damaged, replace.
5. Store in a cool dry place and out of reach of children.
Do not store outdoors.
9. Always check your product is in a safe operating
CABLES
IMPORTANT
cut off plug is inserted into a 13 amp socket.
1. No earth required. Flymo products are double
insulated to EN60335 and under no circum-
stances should an earth be connected to any
part of the product.
2
•
Use only 1.00mm size cable up to 40 metres
length maximum.
Maximum rating :
2
1.00mm size cable, 10 amps 250 volts AC.
2. Ensure the mains voltage suits your product
3. IMPORTANT!
•
YOUR PRODUCT IS SUPPLIED WITH CABLE
WIRED DIRECTLY INTO THE PRODUCT.
The wires in the mains lead are coloured in ac-
cordance with the following code:
1. Flymo Mains Cables and Extension Cables are
available from your local Approved Service Centre.
2. Do not wire an extension cable directly to your
product yourself. Please contact your local Ap-
proved Service Centre for further information on
the connectors and kits available.
BLUE
-
NEUTRAL
LIVE
BROWN
-
The wire which is coloured BLUE must be con-
nected to the Terminal which is marked with the
letter 'N' or coloured BLACK.
3. Only use extension cables specifically designed
for outdoor use.
The wire which is coloured BROWN must be
connected to the Terminal which is marked with
the letter 'L' or coloured RED.
CONNECTORS
IMPORTANT
4. It is important that the outer sheath is clamped
correctly into the 3-pin plug.
•
Flymo connectors are suitable for use with 2 core
cable only. Under no circumstances should these
connectors be used for earthed products.
All Flymo connectors and cables are of splashproof
construction. They are not waterproof and must not
be left outside permanently nor should they be sub-
merged or immersed in water. Do not let cable lay or
trail through pools of water or splashed with water
from hose pipes.
5. If in doubt consult your local Service Repairer or
qualified electrician before the machine is used.
6. A 13 Amp fuse must be fitted to the Mains Plug.
7. The normal plug fuse and household fuse only
protect the electrical equipment and are not a
safeguard against electrocution.
•
If the mains cable is damaged, it must be re-
placed with the correct Flymo assembly from an
Flymo Approved Service Dealer (see leaflet en-
closed in product)
MAINS PLUG REPLACEMENT
IMPORTANT
If the plug supplied is cut off it should be de-
stroyed. There is an electric shock hazard if a
•
Download from Www.Somanuals.com. All Manuals Search And Download.
Blow Tube & Shoulder Harness Assembly
A
B
C
Blow Tube Assembly
Shoulder Harness Assembly
1. Attach the blow tube to the product as shown in Fig
1. Attach the Shoulder Harness to the product as illustrated in Fig B.
2. Adjust the Shoulder Harness as required to ensure it is in
the most comfortable position. (C).
A, ensuring it clicks securely into position.
Suction Tube Assembly
D
Suction Tube Assembly
1. Attach the two Suction Tube halves together as illus-
trated in Pic D. Ensure that the two halves click se-
curely into position.
IMPORTANT
When the Suction Tube halves are attached together,
this is a permanent fixture, they can not be disassem-
bled.
Converting from Blower to Suction
E1
E2
E3
1. Turn the product over and press the release catch on
2. Slide the catch away from the product (E2) and re-
move the Blow Tube from the product (E3).
the Blow Tube (E1).
F1
F2
F3
3. Press the release catch on the Impeller Guard (F1).
4. Release the wire hook (F2).
5. Turn the Impeller Guard anti-clockwise until it can be
removed (F3).
Download from Www.Somanuals.com. All Manuals Search And Download.
G1
G2
G3
H1
H3
6. Attach the assembled Suction Tube to the product
aligning the arrows as indicated (G1).
7. Turn the Suction Tube until it clicks into position (G2).
8. Secure the wire hook into postion and close the catch
(G3).
H2
9. Place the loop on the Debris Bag over the end of
the Suction Tube (H1)
10.Attach the Debris Bag inlet to the product as
shown in Pic H2, ensuring that it clicks securely
into position. (H3)
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Use
J1
J2
Cable Restraint
1. Form loop in mains cable and push the loop
through the slot (J1).
2. To secure, position loop over the hook and
pull the cable back through the slot (J2).
WARNING
K
M
N
L
The use of eye protection is recommended. The use
of ear protection is recommended. To prevent dust irri-
tation, the wearing of a face-mask is recommended.
Never point your product at bystanders.
Using As A Blower
+
-
Blow Mode - The product will blow debris from pa-
tios, paths, driveways, lawns, bushes, borders etc.
1. Point nozzle towards the ground.
2. To start squeeze the switch lever (K).
3. Stand back from debris to be cleared.
4. To control the speed of the blow mode, use the variable
speed dial. Move the dial forward for a faster speed
and backwards for a slower speed (L).
5. Point the tube towards the debris and slowly
approach (M).
6. To stop release the switch lever.
•
If Blow performance is reduced, the blow outlet
may be blocked. Switch off the product and dis-
connect from the mains electricity supply. Re-
move the Blow Tube and clear any blockage in
the blow outlet using a blunt implement (N)
Using As A Vacuum
Vacuum Mode - In this position your product will
pick up leaves, small twigs and garden debris.
•
For best performance, turn speed control to
maximum.
1. Position the tube slightly above the debris,
squeeze the switch lever (E) and move the
product slowly back and forth (P).
3. Do not force the tube into the debris as this will
impair performance.
4. To stop release the switch lever.
•
If Vacuum performance is reduced, the Debis
bag inlet may be blocked. Switch off the prod-
uct and disconnect from the mains electricity
supply. Remove the Debris Bag and clear any
blockage in the Debris Bag inlet using a blunt
implement (Q)
P
Q
Download from Www.Somanuals.com. All Manuals Search And Download.
Emptying the Debris Bag
R1
R2
Emptying the Debris Bag
ꢀ
1. Remove the Debris Bag as described in the
ʻConverting from Blower to Suctionʼ section.
2. Empty debris bag as shown in Pic. R1
D
S
O
NOT PLACE HANDS IN BAG WHEN EMPTYING,
3. RHeA-fRitPthe Debris BagAaUsSEdescribed in the ʻCon-
DEBRIS CAN
C
INJURY (R2)
verting from Blower to Suctionʼ section.
ꢁ
Caring for your product
WARNING Never use water for cleaning your
S1
S3
S2
S4
product, use only a dry cloth. Do not clean with
chemicals or solvents, some can destroy critical
plastic parts.
After Using Your Product
1. Switch off and disconnect from the mains electricity
supply before cleaning your product.
2. Always empty the debris bag.(R1)
3. Inspect the fan for damage and replace if nec-
essary. Clean the fan with a soft brush ensur-
ing it is free from debris (S1)
4. Clean the Debris/Blow Outlet with a soft
brush.(S2)
5. Clean the air vents with a soft brush (S3)
6. Wipe over the product with at dry cloth (S4).
Storing Your Product
Always store the product in a dry place ensuring the
cable is not likely to be damaged on sharp edges
etc.
Fault Finding Hints
Poor Vacuum
Fails To Operate
1. Is the power turned on?
1. Check speed control is at maximum.
2. The air inlets may be blocked, clean all air inlets.
3. The Debris Bag inlet may be blocked. Remove De-
bris Bag and clear blockage with a blunt edge instru-
ment.
2. Is the Blow Tube, Impeller Guard, Suction Tube or
Debris bag fitted correctly?
3. Check the fuse in the plug, if blown replace.
4. Fuse continues to blow?
Immediately disconnect from the mains electricity sup-
ply and consult your local Approved Service Centre
Poor Blowing
1. The air inlets may be blocked, clean all air inlets.
2. Blow outlet may be blocked. Remove Blow Tube and
clear blockage with blunt edge instrument
3. If poor blowing persists?
4. If poor vacuuming persists?
Immediately disconnect from the mains electricity sup-
ply and consult your local Approved Service Centre
Excessive Vibration
1. Inspect the fan for damage and replace if necessary
2. If excessive vibration persists?
Immediately disconnect from the mains electricity sup-
ply and consult your local Approved Service Centre
Immediately disconnect from the mains electricity sup-
ply and consult your local Approved Service Centre
Guarantee & Guarantee Policy
If any part is found to be defective due to faulty manufacture
within the guarantee period, Husqvarna UK Ltd, through its Au-
thorised Service Repairers will effect the repair or replacement
to the customer free of charge providing:
Failures not covered by guarantee
* Failures as a result of not reporting an initial fault.
* Failures as a result of sudden impact.
* Failures as a result of not using the product in accor-
dance with the instructions and recommendations con-
tained in this Operator's Manual.
(a)The fault is reported directly to the Authorised Repairer.
(b)Proof of purchase is provided.
(c)The fault is not caused by misuse, neglect or faulty
adjustment by the user.
* Machines used for hire are not covered by this guar-
antee.
(d)The failure has not occurred through fair wear and tear.
(e)The machine has not been serviced or repaired,
taken apart or tampered with by any person not au-
thorised by Husqvarna UK Ltd.
* The following items listed are considered as wearing
parts and their life is dependent on regular mainte-
nance and are, therefore not normally subject to a
valid warranty claim: Electric Mains cable, Debris Bag.
* Caution!
(f) The machine has not been used for hire.
(g)The machine is owned by the original purchaser.
(h)The machine has not been used commercially.
Husqvarna UK Ltd does not accept liability under the
warranty for defects caused in whole or part, directly
or indirectly by the fitting of replacement parts or addi-
tional parts that are not either manufactured or ap-
proved by Husqvarna UK Ltd, or by the machine
having been modified in any way
*
This guarantee is additional to, and in no way dimin-
ishes the customers statutory rights.
Failures due to the following are not covered, therefore it
is important that you read the instructions contained in
this Operator's Manual and understand how to operate
and maintain your machine:
Download from Www.Somanuals.com. All Manuals Search And Download.
Service Recommendations
your complete machine including cable and any
extension cables used.
1. We strongly recommend that your product is serviced at least
every twelve months, more often in a professional application.
2. Always use genuine Flymo Spare Parts.
A network of specialist dealers can be found in your local Yel-
low Pages. To obtain service on your Flymo product simply
telephone or visit your local Service Centre. Should you re-
quire service under the terms of our guarantee the Service
Centre will require proof of purchase.
3. Prepacked spares are available from most Flymo Approved
Service Dealers (See enclosed leaflet in product).
4. Your product is uniquely identified by a silver and
black product rating label
All of the centres listed stock genuine Flymo Spare Parts.
NOTE: Our Service Repairers act on their own behalf
and are not empowered to commit or legally bind
Husqvarna UK Ltd in any manner whatsoever.
5. If you have a problem with your machine contact your local
Approved Service Centre ensuring you have full details of
your product as described on the product rating label.
6. Should it be necessary for work to be carried out
by your Service Centre, it is important to take
Environmental Information
•
•
Awareness of the environment must be considered
when disposing of ʻend-of-lifeʼ product.
If necessary, contact your local authority for disposal
information.
the recycling of electrical and electronic equipment. By ensuring
this product is disposed of correctly, you will help prevent poten-
tial negative consequences for the environment and human
health, which could otherwise be caused by inappropriate waste
handling of this product. For more detailed information about re-
cycling of this product, please contact your local council office,
your household waste disposal service or the shop where you
The symbol
on the product or on its packaging indicates
that this product may not be treated as household waste. In-
stead it shall be handed over to the applicable collection point for purchased the product.
EC Declaration of Conformity
Husqvarna UK Ltd., Aycliffe Industrial Park
Newton Aycliffe, Co. Durham, DL5 6UP, England
Declare under our sole responsibility that the product(s);
Category........................................ Electric Leaf Collector
Model(s).........................................TGV2700
Identification of Series................... See Product Rating Label
Year of Construction...................... See Product Rating Label
Complies with the essential requirements & provisions of the following EC Directives:
98/37/EC (until 31.12.09), 2006/42/EC (from 01.01.10), 2004/108/EC, 2000/14/EC
based on the following standards applied:
IEC60335-1, IEC60335-2-100, EN50366, EN55014-1, EN55014-2, EN61000-3-2, EN61000-3-3
The maximum A weighted sound pressure level LpA at the operatorʼs position, recorded on a sample of the above
product(s) corresponds to the Level given in the table.
The maximum hand / arm vibration weighted value measured according to EN ISO 5349 on a sample of the above
product(s) corresponds to the Value given in the table.
2000/14/EC: The Measured Sound Power LWA & Guaranteed Sound Power LWA values are according to the tabulated
figures.
Conformity Assessment Procedure.................. Annex VI
Notified Body.................................................... Intertek, Cleeve Road
Leatherhead, Surrey
KT22 7SB, England
Newton Aycliffe, 06/05/2008
M. Bowden,
Research & Development Director
Husqvarna UK Ltd.
TGV2700
Type
Speed of Rotation of Cutting Device (RPM)
17,000
2.7
Power (kW)
99
Measured Sound Power LWA (dB(A))
Guaranteed Sound Power LWA (dB(A))
Level (dB(A))
100
85.7
2.84
4.7
2
Value (m/s )
Weight (Kg)
Husqvarna UK Ltd
Aycliffe Industrial Park
NEWTON AYCLIFFE
Co.Durham DL5 6UP
ENGLAND
Telephone - 01325 302302 Fax - 01325 310339
Our policy of continuous improvement means that the specification of products may be altered from time to time without prior notice.
5100005-01
Download from Www.Somanuals.com. All Manuals Search And Download.
|