Extron electronic Switch CSVEQ 100 D User Manual

User’s Manual  
CSVEQ 100 D  
Composite Video and S-Video Line Driver  
with Audio  
Extron USA - West Extron USA-East Extron Europe  
Extron Asia  
Extron Japan  
Extron China  
Extron Dubai  
Headquarters  
+800.633.9876  
+800.3987.6673  
+800.7339.8766  
+81.3.3511.7655  
+81.3.3511.7656 FAX  
+400.883.1568  
+971.4.2991800  
+971.4.2991880 FAX  
Inside USA / Canada Only  
Inside Europe Only  
Inside Asia Only  
Inside China Only  
+800.633.9876  
68-1598-01 Rev. A  
Inside USA / Canada Only  
+1.919.863.1794  
+1.919.863.1797 FAX  
+31.33.453.4040  
+31.33.453.4050 FAX  
+65.6383.4400  
+65.6383.4664 FAX  
+86.21.3760.1568  
+86.21.3760.1566 FAX  
08 08  
+1.714.491.1500  
+1.714.491.1517 FAX  
© 2008 Extron Electronics. All rights reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
警告  
安全须知 中文  
这个符号提示用户该设备用户手册中  
电源 设备只能使用产品上标明的电源。 设备  
必须使用有地线的供电系统供电。 第三条线  
(地线)是安全设施,不能不用或跳过。  
有重要的操作和维护说明。  
拔掉电源 为安全地从设备拔掉电源,请拔掉所有设备后  
或桌面电源的电源线,或任何接到市电系统的电源线。  
这个符号警告用户该设备机壳内有暴  
露的危险电压,有触电危险。  
电源线保护 妥善布线, 避免被踩踏,或重物挤压。  
维护 所有维修必须由认证的维修人员进行。 设备内部  
没有用户可以更换的零件。为避免出现触电危险不要自  
己试图打开设备盖子维修该设备。  
注意  
阅读说明书 户使用该设备前必须阅读并理  
解所有安全和使用说明。  
通风孔 有些设备机壳上有通风槽或孔,它们是用来防止  
机内敏感元件过热。 不要用任何东西挡住通风孔。  
保存说明书 用户应保存安全说明书以备将来使  
用。  
锂电池 不正确的更换电池会有爆炸的危险。 必须使用  
与厂家推荐的相同或相近型号的电池。 按照生产厂的  
建议处理废弃电池。  
遵守警告 用户应遵守产品和用户指南上的所有安  
全和操作说明。  
避免追加 不要使用该产品厂商没有推荐的工具或  
追加设备,以避免危险。  
FCC Class A Notice  
This equipment has been tested and found to comply with the limits for a Class A digital device,  
pursuant to part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this  
device may not cause harmful interference, and (2) this device must accept any interference received,  
including interference that may cause undesired operation. The Class A limits are designed to  
provide reasonable protection against harmful interference when the equipment is operated in  
a commercial environment. This equipment generates, uses, and can radiate radio frequency  
energy and, if not installed and used in accordance with the instruction manual, may cause harmful  
interference to radio communications. Operation of this equipment in a residential area is likely to  
cause harmful interference, in which case the user will be required to correct the interference at his  
own expense.  
This unit was tested with shielded cables on the peripheral devices. Shielded cables must be used  
with the unit to ensure compliance with FCC emissions limits.  
N
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Quick Start Guide — CSVEQ 100 D  
Installation and service must be performed by authorized  
personnel only. These line drivers must be used with UL  
approved, grounded electrical boxes.  
C
To install and set up the line driver, follow these steps and see the  
appropriate sections of this manual for details.  
Step 1  
Turn the input and output devices off and unplug their power cords.  
Verify that the line driver is disconnected from the power source  
before proceeding.  
Step 2  
Attach output cables to the rear panel of the line driver and to the  
output devices. See "Rear Panel Features and Operation" in chapter 3  
for details.  
Step 3  
Attach input cables from the input devices to the line driver’s front  
panel input connectors. See "Front Panel Features and Operation" in  
chapter 3.  
Step 4  
Connect power cords and turn on the output devices (projector/  
monitor, speakers) and input devices.  
Step 5  
The picture should appear and sound should be audible. If not,  
ensure that all devices are plugged in and receiving power. Check  
the cabling, make adjustments as needed. For further details, see  
"Testing and troubleshooting" in chapter 2.  
Step 6  
While watching the display, adjust the video gain and  
equalization by using the rotary gain and equalization (EQ) control  
potentiometers. An oscilloscope can be used to achieve a more  
precise adjustment. See “Gain adjustment control" and "Equalization  
(EQ) adjustment control” in chapter 3 for details.  
Make all adjustments using an Extron Tweeker or small screwdriver.  
If using very short output cables, set all potentiometers to the default  
setting (the arrow on the control pointing to the dot beside it).  
CSVEQ 100 D • Quick Start Guide  
QS-1  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Quick Start — CSVEQ 100 D, cont’d  
When using long cables, follow these steps:  
a. Supply the color bars test signal to the input. (Recommendation:  
use an Extron VTG 300 Video Test Generator to generate the test  
signal.)  
b. Adjust the Gain control(s) for the output until the signal level  
at the far end is the same as the input (or the display shows the  
correct brightness and contrast).  
c. Adjust the EQ control for the output so that no overshoot or  
round front corner appears at the far end on the oscilloscope or  
you see a sharp picture with no smearing.  
Step 7  
See "Installation Instructions" in chapter 2 for further installation  
details.  
CSVEQ 100 D • Quick Start Guide  
QS-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table of Contents  
All trademarks mentioned in this manual are the properties of their respective owners.  
68-1598-01 Rev. A  
08 08  
CSVEQ 100 D Table of Contents  
TOC-i  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table of Contents, cont’d  
CSVEQ 100 D • Table of Contents  
TOC-ii  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CSVEQ 100 D  
Chapter One  
1
Introduction  
About this Manual  
Features  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Introduction  
About this Manual  
The CSVEQ 100 D is a high performance composite video,  
S-video, and audio line driver designed to compensate for signal  
attenuation and high frequency loss encountered during long  
cable runs. It is capable of simultaneously driving composite  
video and S-video plus audio signals up to 1000 feet (300 m)  
on Extron MHR or RG59 high resolution video cables and STP  
series audio cables. The CSVEQ 100 D mounts in a Decora®  
style wallplate and is ideal for use in residential and commercial  
environments where video and audio signals need to be  
extended over a long distance.  
Features  
Long distance line driving — Drives composite video or  
S-video signals up to 1000 feet (300 meters) using Extron's  
MHR cable.  
Balanced or unbalanced stereo or dual mono output —  
Unbalanced stereo audio input can be output as balanced  
or unbalanced stereo audio or as dual mono.  
Video gain adjustment — Offers a video gain adjustment for  
composite video and Y of S-video with a range of  
-1 dB to +3 dB, and C of S-video with a range of 0 dB to  
+10 dB.  
Equalization adjustment — Features an equalization  
adjustment range of 0 dB to +7 dB at 5 MHz that changes  
the level and peaking of the output signal to compensate  
for use of long cables.  
Stereo or dual mono output jumper — A rear panel jumper  
selects between stereo and dual mono output formats.  
Front panel LED indicator — Indicates when the line driver is  
receiving power or a video signal.  
Compatibility — Compatible with NTSC, PAL, and SECAM  
CSVEQ 100 D • Introduction  
1-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
CSVEQ 100 D  
Chapter Two  
2
Installation  
Application Examples  
Installing the CSVEQ 100 D  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Installation  
Application Example  
To get started, refer to the "Quick Start Guide" at the beginning  
of this manual.  
Installation and service must be performed by  
authorized personnel only.  
C
Extron  
MPA 122  
Mini Power  
Ampliꢀer  
Extron  
SI 26X  
Two-way Ceiling  
Speakers  
Balanced  
Audio  
S-Video  
Extron  
CSVEQ 100 D  
Projector  
Composite Video, S-Video,  
and Audio Line Driver  
Composite  
Video  
S-VIDEO IN  
VIDEO IN  
1,000 Feet  
R
-
AUDIO IN  
L
DVD/VCR  
Combo  
CSVEQ 100 D application example  
CSVEQ 100 D • Installation  
2-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Installing the CSVEQ 100 D  
The CSVEQ 100 D is a wall-mounted product and can be  
mounted into an electrical wall box. This section includes site  
preparation, wall box installation, and the mounting of the line  
driver in the wall box.  
The line driver must be installed into an Underwriters  
Laboratories (UL) approved electrical wall box. The  
box is not included with the line driver; the installer is  
responsible for obtaining and installing the box.  
N
Preparing the site and installing the wall box  
Choose a location that allows cable runs without interference.  
Allow enough depth for both the wall box and the cables. You  
may need to install the cables into the wall or conduits before  
installing the line driver.  
The line driver can be installed in a standard one-gang electrical  
wall box. The installation must conform to national and local  
electrical codes. A dimensional drawing and a cutout template  
of the line driver are provided in appendix B of this manual.  
The cutout template shown in appendix B is not full size.  
Pay attention to the measurements shown on the template.  
N
1.  
Mark the guidelines for the opening on the wall.  
If the line driver is to be installed in a wall box, place  
the box against the installation surface and draw a line  
on it around the outside of the box.  
If the line driver is to be installed without a wall box  
(fastening it directly to the wall), measure and mark  
the surface for the cutout area indicated in the cutout  
template.  
2.  
3.  
Cut out the material from the marked area.  
Check the opening size by inserting the wall box (if used)  
or the line driver (if no box is used) into the opening. The  
box and line driver should fit easily into the opening.  
Enlarge or smooth the edges of the opening if needed.  
4.  
5.  
Feed cables through the wall box punch-out holes, and  
secure them with cable clamps to provide strain relief.  
Insert the wall box into the opening, and attach it to the  
wall or stud using nails or screws. The front edge should  
be flush with the outer wall surface. See the following  
illustration.  
CSVEQ 100 D • Installation  
2-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Installation, cont’d  
Wall Stud  
Wall Stud  
e
Installation Cable  
Cable Clamp  
lamp  
Nails  
Screws or Nails  
Attaching the wall box to a wall stud  
If attaching the wall box to wood, use four #8 or #10  
screws or 10-penny nails. A minimum of ½" (1.3 cm) of  
screw threads must penetrate the wood.  
If attaching the wall box to metal studs, use four #8 or  
#10 self-tapping sheet metal screws or machine bolts with  
matching nuts.  
Mounting the line driver  
Before mounting the line driver and if it has not already been  
tested, test the system to make sure that the connections and  
settings are correct. See "Testing and troubleshooting" in this  
chapter.  
If the system is operating correctly, the line driver can be  
installed in the wall. Adjust the gain and equalization, and set  
the Audio Out switch to Stereo or Dual Mono before fastening  
the line driver into the wall box. The controls and cables will  
be inaccessible after installation. See “Rear Panel Features  
and Operation" in chapter 3 for details about settings and  
adjustments.  
Continue mounting the line driver by following the steps below.  
1.  
Remove power from the line driver by disconnecting the  
power supply from the AC source.  
2.  
3.  
Connect the output cables to the rear of the device.  
Place the line driver through the opening in the wall and  
into the wall box. Take care not to damage the output  
cable(s), which fit behind the line driver at the back of the  
wall box.  
CSVEQ 100 D • Installation  
2-4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
4.  
Mount the line driver to the wall box with machine screws  
as shown in the following illustration.  
Wall Box  
Extron  
CSVEQ 100 D  
S-VIDEO  
IN  
VIDEO IN  
Wall opening  
R
AUDIO IN  
L
is flush with  
edge of box.  
Decora  
Faceplate  
Mounting the line driver to a wall box  
5.  
6.  
Attach the Decora® wall plate to the line driver as shown in  
the illustration above.  
Reconnect the power supply, connect input cables to the  
line driver, and restore power to the equipment.  
Installing the mud ring bracket  
The CSVEQ 100 D can also be installed using the included mud  
ring bracket. See the illustration below.  
1.  
Once the proper wall location for mounting the line driver  
has been determined, cut an opening in the wall using the  
proper mounting template found in the appendix.  
2.  
3.  
Carefully cut away the mounting surface material inside  
the traced template lines  
Test the fit of the mud ring. The doglegs should fit easily  
into the hole and the flat portion should rest flush against  
the wall. See the note in the following illustration.  
4.  
Rotate all doglegs inward.  
CSVEQ 100 D • Installation  
2-5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Installation, cont’d  
5.  
6.  
Insert the mud ring into the hole.  
Tighten all of the dogleg screws until the doglegs clamp  
the mud ring to the mounting surface. Do not overtighten.  
Standard mud rings only: If you are going to screw the  
mud ring to the surface, rather than using the detachable  
doglegs, mark the four surface mounting screw holes at the  
corners of the mud ring.  
Wall  
Extron  
Wall Mounting Bracket  
Extron  
CSVEQ 100 D  
S-VIDEO  
IN  
N
VIDEO  
I
R
AUDIO IN  
L
Decora  
Faceplate  
Installation using a mud ring  
CSVEQ 100 D • Installation  
2-6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Testing and troubleshooting  
1.  
Apply power to the line driver. The power/signal LED on  
the line driver lights amber (power) or green (video input).  
2.  
If the LED does not light, check the wiring at both the line  
driver and the power supply, and make sure the power  
supply is connected to a power source.  
If the image does not appear or there is no sound  
1.  
2.  
Make sure that all the devices are powered on.  
Ensure that the connectors are wired correctly at both  
ends of the cables. Audio cables must be wired for an  
unbalanced stereo input signal and for the appropriate  
(unbalanced or balanced) output signal.  
3.  
4.  
Check the video source’s user’s guide or contact Extron to  
determine if there are special requirements to output video  
to the external video port.  
Call the Extron S3 Sales and Technical Support Hotline if  
the image still does not appear or there is no sound.  
If the image is not displayed correctly  
1.  
If the picture is too bright or too dark, or if the edges of the  
image seem to exceed their boundaries, or if thin lines and  
sharp edges look thick and fuzzy, change the gain setting.  
If the picture appears and is stable, but it has ghosting  
or blooming, verify that the video input is properly  
terminated. If the problem is not resolved by changing the  
termination, try using a different input cable. Poor quality  
or damaged cable can cause ghosting and blooming.  
2.  
If the picture still is not displayed correctly, call the Extron  
S3 Sales and Technical Support Hotline.  
CSVEQ 100 D • Installation  
2-7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Installation, cont’d  
CSVEQ 100 D • Installation  
2-8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CSVEQ 100 D  
Chapter Three  
3
Operation  
Front Panel Features and Operation  
Rear Panel Features and Operation  
Replacing the Decora Faceplate  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Operation  
Front Panel Features and Operation  
Wall Plate  
Faceplate  
1
S-VIDEO  
IN  
VIDEO IN  
3
4
2
AUDIO IN  
L
R
Wall Plate  
Mounting Screw  
CSVEQ 100 D  
Front Panel  
Power indicator LED — This LED lights:  
a
• Amber when the line driver is receiving full power  
• Green when the line driver is receiving a video signal  
Video input connector — Connect a composite video input  
source to this RCA connector.  
b
c
S-video input connector — Connect an S-video input source to  
this 4-pin mini DIN connector. See the following pinout table.  
3
4
1
2
S-video Pinout Table  
NAME DESCRIPTION  
PIN  
1
GND  
GND  
Y
Ground (Y)  
Ground (C)  
Luminance  
Chrominance  
2
3
4
C
CSVEQ 100 D • Operation  
3-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Audio input connectors — Connect an unbalanced stereo audio  
source to these left (L) and right (R) RCA connectors. Wire the  
male connector as shown in the following illustration.  
d
Tip (+)  
Sleeve (  
)
CSVEQ 100 D • Operation  
3-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operation, cont’d  
Rear Panel Features and Operation  
CSVEQ 100 D  
5
6
7
8
9
AUDIO  
OUTPUT  
CONFIG  
JUMPER POSITION  
OFF = DUAL MONO  
ON = STEREO  
4
AUDIO OUTPUT  
3
1
2
CSVEQ 100 D Rear Panel  
Power connector — Connect the external 12 VDC power supply  
into this 2-pin, 3.5 mm direct insertion connector. The power  
supply is included with the unit. The "Power supply wiring"  
section in this chapter explains how to wire the connector.  
a
b
Audio output connector — Wire a balanced/unbalanced audio  
output device to this 3.5 mm, 5-pole, direct insertion captive  
screw connector. See the following wiring diagrams.  
CSVEQ 100 D • Operation  
3-4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Balanced Stereo  
Unbalanced Stereo  
Left Tip (+)  
Left Tip (+)  
Left Ring (-)  
Sleeve (s)  
Right Tip (+)  
Right Ring (-)  
Sleeve  
Right Tip (+)  
AUDIO  
OUTPUT  
CONFIG  
AUDIO  
OUTPUT  
CONFIG  
JUMPER POSITION  
OFF = DUAL MONO  
ON = STEREO  
JUMPER POSITION  
OFF = DUAL MONO  
ON = STEREO  
Set Audio Output jumper to Stereo.  
Set Audio Output jumper to Stereo.  
Balanced Mono  
Unbalanced Mono  
Use either the left or the right channel.  
Use either the left or the right channel.  
Tip (+)  
Ring (-)  
Sleeve  
Tip (+)  
Sleeve  
AUDIO  
OUTPUT  
CONFIG  
AUDIO  
OUTPUT  
CONFIG  
JUMPER POSITION  
OFF = DUAL MONO  
ON = STEREO  
JUMPER POSITION  
OFF = DUAL MONO  
ON = STEREO  
Set Audio Output jumper to Dual Mono.  
Set Audio Output jumper to Dual Mono.  
CAUTION Connect the sleeve to ground  
(Gnd). Connecting the sleeve to  
a negative (–) terminal will  
damage the audio output  
circuits.  
Do not tin the wires!  
Balanced audio is more resistant to noise and can be driven  
for longer distances than unbalanced audio. For best  
results, wire the output for balanced audio.  
N
Video output connector (green cable) — Connect a composite  
video output device to the BNC connector.  
c
S-video Y connector (luma, white cable) — Connect the luma of  
an S-video output device to the BNC connector.  
S-video C connector (chroma, yellow cable) — Connect the  
chroma of an S-video output device to the BNC connector.  
Audio output jumper — Set this jumper to select either stereo  
(jumper on) or dual mono (jumper off) output.  
d
e
When set for dual mono, the left and right channels output the  
same signal (either channel or both channels can be used). The  
audio output can be wired for balanced/unbalanced mono or  
stereo output. The wiring and the jumper setting must match.  
Output gain potentiometer (chroma) — Use a small  
screwdriver to rotate this potentiometer to adjust the chroma  
gain when the line driver is connected to long output cables.  
The adjustment range is 0 dB to +10 dB. The default is unity  
(the dot position). See "Gain adjustment control" in this chapter.  
CSVEQ 100 D • Operation  
3-5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operation, cont’d  
Output equalization (EQ) potentiometer (luma) — Use a  
f
small screwdriver to rotate this control to adjust equalization  
when the line driver is connected to long output cables. The  
adjustment range is 0 dB to +7 dB. The default is set to 0 dB (the  
dot position). See "Equalization (EQ) adjustment control" in this  
chapter.  
Output gain potentiometer (luma) — Use a small screwdriver  
to rotate this potentiometer to adjust the luminance gain  
when the line driver is connected to long output cables. The  
adjustment range is -1 dB to +3 dB. The default is unity (the dot  
position). See "Gain adjustment control" in this chapter.  
g
h
i
Output gain potentiometer (video) — Use a small screwdriver  
to rotate this control to adjust the gain when the line driver is  
connected to long output cables. The adjustment range is -1  
dB to +3 dB. The default is unity (the dot position). See "Gain  
adjustment control" in this chapter.  
Output equalization (EQ) potentiometer (video) — Use a  
small screwdriver to rotate this control to adjust equalization  
when the line driver is connected to long output cables. The  
adjustment range is 0 dB to +7 dB. The default is set to 0 dB (the  
dot position). See "Equalization (EQ) adjustment control" in this  
chapter.  
Power supply wiring  
Wire the line driver's power connector as shown below.  
Smooth  
Ridges  
3
A
A
5
SECTION A–A  
Power Supply  
Output Cord  
Captive Screw  
Connector  
Power connector wiring  
Power supply voltage polarity is critical. Incorrect  
voltage polarity can damage the power supply and the  
line driver. Identify the power cord negative lead by  
the ridges on the side of the cord.  
C
To verify the polarity before connection, plug in the power  
supply with no load and check the output with a voltmeter.  
CSVEQ 100 D • Operation  
3-6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
The two power cord wires must be kept separate while  
the power supply is plugged in. Remove the power  
before wiring.  
W
Do not tin the power supply leads before installing in the  
direct insertion connector. Tinned wires are not as secure  
in the connectors and could be pulled out.  
N
Gain adjustment control  
The gain control adjusts picture brightness by compensating  
for signal amplitude loss caused by cable resistance. To adjust  
the output gain, view the display while using a small, flat-blade  
screwdriver to rotate the potentiometer. This control produces  
a gain adjustment ranging from -1 dB to + 3 dB (video and luma  
of S-video) and from 0 dB to +10 dB (chroma of S-video). Select  
the setting that gives the best picture brightness.  
The gain control is a potentiometer with a mechanical stop  
at the high and the low end. After you have reached the  
high or low end of the adjustment, no change is apparent  
on the display. The default is unity (the dot position)  
N
You can judge the adjustment visually by viewing the display.  
For a more precise setting use an oscilloscope or a waveform  
monitor connected to the far end of the output cable, and adjust  
the gain so that the level at the waveform monitor is 100 IRE.  
Equalization (EQ) adjustment control  
The equalization control adjusts the output level and peaking  
to get a sharp picture. This adjustment changes the level and  
peaking of the output signal to compensate for capacitance  
caused by up to 1000 feet (300 meters) of Extron MHR cable.  
This control produces an equalization adjustment ranging from  
0 dB to + 7 dB (video and luma of S-video).  
CSVEQ 100 D • Operation  
3-7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Operation, cont’d  
Use a small, flat-blade screwdriver to rotate this control. View  
the display and select the setting that gives the sharpest picture.  
For a more precise setting, you can use an oscilloscope or a  
waveform monitor connected to the far end of the output  
cable, and adjust the equalization so that the color burst ranges  
between -20 IRE and +20 IRE.  
The EQ control is a potentiometer with a mechanical stop  
at the high and the low end. After you have reached the  
high or low end of the adjustment, no change is apparent  
on the display. The default is set to 0 dB (the dot position).  
N
Replacing the Decora Faceplate  
The front faceplate is replaced by removing the two rear panel  
mounting screws, replacing the faceplate, then reattaching the  
two screws, as shown in the CSVEQ 100 D example below.  
CSVEQ 100 D  
AUDIO  
OUTPUT  
CONFIG  
JUMPER POSITION  
OFF  
ON  
=
DUAL MONO  
=
STEREO  
AUDIO OUTPUT  
Mounting  
Screws  
Faceplate (rear)  
Removing the CSVEQ 100 D faceplate  
CSVEQ 100 D • Operation  
3-8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
CSVEQ 100 D  
Appendix A  
A
Specifications, Part Numbers,  
and Accessories  
Specifications  
Included Parts  
Optional Accessories  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Specifications, Part Numbers, and Accessories  
Specifications  
Video  
Gain................................................. Composite video and Y of S-video:  
-1 dB to +3 dB (x0.9 to x1.4), adjustable  
C of S-video: 0 dB to +10 dB (x1 to x3),  
adjustable  
Equalization................................... 0 dB to +7 dB (x1 to x2) at 5 MHz,  
adjustable  
Bandwidth (Y of S-video)............. 185 MHz (-3 dB)  
Output cable driving distance..... Up to 1000' (300 m) with Extron MHR  
cable  
Video input  
Number/signal type..................... 1 S-video, 1 composite video  
Connectors ..................................... 1 female 4-pin mini DIN, 1 female RCA  
Nominal level ................................ 1 Vp-p for Y of S-video, and for composite  
video (including sync)  
0.3 Vp-p for C of S-video  
Minimum/maximum levels........ 0.4 to 2.0 Vp-p with no offset at unity gain  
for composite video (including sync) or  
for Y of S-video  
Impedance...................................... 75 ohms  
Return loss...................................... <-25 dB @ 0 to 5 MHz  
DC offset (max. allowable)........... 4.0 V  
Input coupling............................... AC  
Video output  
Number/signal type..................... 1 composite video, 1 S-video  
Connectors ..................................... 3 female BNC attached via 4" pigtails  
Nominal level ................................ 1 Vp-p for Y of S-video, and for composite  
video (including sync)  
0.3 Vp-p for C of S-video  
Minimum/maximum levels........ 0.4 to 2.0 Vp-p (follows input)  
Impedance...................................... 75 ohms  
Return loss...................................... -30 dB @ 5 MHz  
DC offset......................................... ±5 mV with no input signal  
Floating: +0.1 to -0.6 V, depending on  
input signal content  
CSVEQ 100 D • Specifications and Parts  
A-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Sync  
Standards........................................ NTSC 3.58, NTSC 4.43, PAL, SECAM  
Audio  
Gain................................................. Unbalanced output: 0 dB; balanced output:  
+6 dB  
Frequency response ...................... 20 Hz to 20 kHz, ±0.5 dB  
THD + Noise.................................. 0.03% @ 1 kHz at nominal level  
S/N.................................................. >90 dB at maximum output (unweighted)  
Stereo channel separation ............ >80 dB @ 1 kHz  
Output cable driving distance..... Up to 1000' (300 m) with Extron STP cable  
Audio input  
Number/signal type..................... 1 stereo unbalanced  
Connectors ..................................... 2 female RCA  
Impedance...................................... 18k ohms unbalanced, DC coupled  
Nominal level ................................ -10 dBV (316 mVrms)  
Maximum level.............................. +8 dBV, unbalanced at 1% THD+N  
0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV 2 dBu  
N
Audio output  
Number/signal type..................... 1 stereo or dual mono (jumper-selectable),  
balanced/unbalanced  
Connectors ..................................... (1) 3.5 mm direct insertion captive screw  
connector, 5 pole  
Impedance...................................... 50 ohms unbalanced, 100 ohms balanced  
Gain error ....................................... ±0.5 dB channel to channel  
Nominal level ................................ -10 dBV, unbalanced; -2 dBu, balanced  
Maximum level ............................. +9 dBV, unbalanced; +17 dBu, balanced at  
1% THD+N with a 10k ohm load  
General  
External power supply................. 100 VAC to 240 VAC, 50/60 Hz, external;  
to 12 VDC, 2 A, regulated  
Power input requirements........... 12 VDC, 0.2 A  
CSVEQ 100 D • Specifications and Parts  
A-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications, Part Numbers, Accessories, cont’d  
Temperature/humidity................ Storage: -40 to +158 °F (-40 to +70 °C) /  
10% to 90%, noncondensing  
Operating: +32 to +122 °F (0 to +50 °C) /  
10% to 90%, noncondensing  
Cooling ........................................... Convection, no vents  
Mounting........................................ Wall or furniture mountable with standard  
US electrical wall boxes or mud rings  
Enclosure........................................ Metal rear enclosure, plastic faceplate  
Enclosure dimensions  
Faceplate............................. 2.6" H x 1.3" W x 0.1" D  
(6.6 cm H* x 3.3 cm W x 0.3 cm D)  
(Fits the opening in a 1 gang Decora®  
faceplate. *Height is 3.8" [9.5 cm],  
including mounting tabs.)  
(Depth excludes connectors.)  
Device ................................. 2.7" H x 1.8" W x 0.75" D  
(6.9 cm H x 4.6 cm W x 1.9 cm D)  
(Depth excludes connectors; height  
excludes mounting tabs.)  
Product weight .............................. 0.2 lbs (0.1 kg)  
Shipping weight ............................ 2 lbs (1 kg)  
Vibration......................................... ISTA 1A in carton (International Safe  
Transit Association)  
Listings............................................ UL, CUL  
Regulatory compliance  
Safety................................... CE, C-tick, CUL, UL  
EMI/EMC .......................... CE, C-tick, FCC Class A, ICES, VCCI  
MTBF............................................... 30,000 hours  
Warranty......................................... 3 years parts and labor  
All nominal levels are at 10%.  
N
N
Specifications are subject to change without notice.  
CSVEQ 100 D • Specifications and Parts  
A-4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Included Parts  
These items are included in each order of the CSVEQ 100 D.  
Included parts  
Replacement  
part number  
CSVEQ 100 D (black, white)  
60-951-02, -03  
Faceplate, black (included  
with 60-951-02 only)  
21-xxx-0xLF  
Faceplate, white (included  
with 60-951-03 only)  
21-xxx--0xLF  
Decora® wall plate, black  
included with 60-951-02  
only)  
Decora® wall plate, white  
(included with 60-951-03  
only)  
One-gang Decora® mud ring  
70-581-12  
12 VDC, 2 A external power  
supply  
28-181-01LF  
IEC power cord  
User’s manual  
Optional Accessories  
These items are optional accessories for the CSVEQ 100 D.  
Accessory  
Part number  
MHR-2 mini high resolution non-plenum  
cable, bulk  
22-123-xx  
22-129-xx  
22-145-xx  
22-146-xx  
22-098-xx  
22-164-xx  
MHR-2P mini high resolution plenum  
cable, bulk  
RG59 high resolution non-plenum cable,  
bulk  
RG59P high resolution plenum cable,  
bulk  
RG6 super high resolution non-plenum  
cable, bulk  
RG6P super high resolution plenum  
cable, bulk  
CSVEQ 100 D • Specifications and Parts  
A-5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Specifications, Part Numbers, Accessories, cont’d  
Accessory  
Part number  
MHR-2 SV mini high resolution S-video  
cables  
26-316-xx  
AV RCA cable  
STP cable  
IN8906, IN8920  
Various  
CSVEQ 100 D • Specifications and Parts  
A-6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CSVEQ 100 D  
Appendix B  
B
Dimensions and Template  
CVEQ 100 D Dimensions  
Cut-out Template  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Dimensions and Template  
CSVEQ 100 D Dimensions  
Dimensions are shown in inches [mm}.  
0.06” (0.15 cm)  
0.46” (1.55 cm)  
0.10” (0.25 cm)  
2.83” (7.19 cm)  
0.00” (0.00 cm)  
2.72” (6.91 cm)  
1.92” (4.86 cm)  
0.92” (2.32 cm)  
0.11” (0.28 cm)  
0.00” (0.00 cm)  
2.74” (6.96 cm)  
Front View  
Side View  
CSVEQ 100 D • Dimensions and Template  
B-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Cut-out Template  
Always check and go by the dimensions given in this  
appendix. The template is not full size.  
N
Cut-Out Template for the Extron  
CSVEQ 100 D  
2.79"  
(7.09 cm)  
Wall Plate  
1.75"  
(4.5 cm)  
Location of Line Driver  
2.8"  
4.50"  
(7.1 cm)  
(11.43 cm)  
SURFACE  
CUT-OUT AREA  
FOR  
To install  
FURNITURE  
MOUNT  
line driver  
directly into  
furniture or wall,  
cut along this line.  
TEMPLATE IS NOT FULL SIZE  
CSVEQ 100 D • Dimensions and Template  
B-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Dimensions and Template, cont’d  
CSVEQ 100 D • Specifications and Parts  
B-4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CSVEQ 100 D • Specifications and Parts  
B-5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Dimensions and Template, cont’d  
CSVEQ 100 D • Specifications and Parts  
B-6  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Crown Audio Stereo Amplifier D 150 User Manual
Desa Water Heater CGN10T User Manual
DXG Technology Camcorder DXG 5B7V User Manual
Eaton Electrical Marine Battery ETN1000 User Manual
Edelbrock Automobile 4760 User Manual
Fisher Price Baby Toy 77506 User Manual
Fisher Price Motorized Toy Car W2604 User Manual
Fostex Computer Drive MR 8HD CD User Manual
FujiFilm Digital Camera 7666 User Manual
GE Air Conditioner AEM18DL User Manual