Evo Fitness Treadmill EVO 3I User Manual

USER’S MANUAL  
EVO 3i MOTORIZED TREADMILL  
MODEL NUMBER: EVO 3i  
USER WEIGHT LIMITATION: 400lbs.  
TOLL FREE CUSTOMER SERVICE NUMBER: 1.888.800.1167  
SERIAL NUMBER (found on frame):  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3
EVO 3i MOTORIZED TREADMILL  
POWER REQUIREMENTS  
Power Requirements:  
IMPROPER CONNECTION OF THE EQUIPMENT GROUNDING CONNECTOR CAN RESULT IN A RISK OF AN  
ELECTRIC SHOCK. CHECK WITH A QUALIFIED ELECTRICIAN OR SERVICE MAN IF YOU ARE IN DOUBT AS TO  
WHETHER THE PRODUCT IS PROPERLY GROUNDED. DO NOT MODIFY THE PLUG PROVIDED WITH THE  
PRODUCT, IF IT WILL NOT FIT THE OUTLET; HAVE A PROPER OUTLET INSTALLED BY A QUALIFIED ELECTRICIAN.  
This treadmill can be seriously damaged by sudden voltage changes in your home’s electrical power. Voltage spikes, surges  
and noise interference can result from weather conditions or from other appliances being turned on or off. To reduce the  
possibility of treadmill damage, always use a surge protector (not included) with your treadmill.  
Surge protectors can be purchased at most hardware stores. The manufacturer recommends a single outlet surge protector  
with a UL 1449 rating as a Transient Voltage Surge Suppressor (TVSS) with a UL suppressed voltage rating of 400V or less  
and an electrical rating 120VAC, 15 amps.  
This treadmill must be grounded to reduce the risk of electrical shock. Grounding provides a path of least resistance for  
electric current, should the treadmill malfunction. This treadmill comes with an electrical cord having an equipment-grounding  
conductor and a grounding plug. Always plug the power cord into a surge protector, and plug the surge protector into an  
appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.  
This product is for use on a nominal 120-volt circuit, and has a grounding plug that looks like the plug illustrated in the  
drawing below.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4
EVO 3i MOTORIZED TREADMILL  
PREASSEMBLY  
Open the boxes:  
You are now ready to open the boxes of your new equipment. Make sure to inventory all of the parts that are included in the  
boxes. Check the Hardware Comparison Chart for a full count of the number of parts included for this product to be  
assembled properly. If you are missing any parts or have any assembly questions call your local Smooth Retailer.  
Gather your tools:  
Before starting the assembly of your unit, make sure that you have gathered all the necessary tools you may require to  
assemble the unit properly. Having all of the necessary equipment at hand will save time and make the assembly quick and  
hassle-free.  
Clear your work area:  
Make sure that you have cleared away a large enough space to properly assemble the unit. Make sure the space is free  
from anything that may cause injury during assembly. After the unit is fully assembled, make sure there is a comfortable  
amount of free area around the unit for unobstructed operation.  
Invite a friend:  
Some of the assembly steps may require heavy lifting. It is recommended that you obtain the assistance of another person  
when assembling this product.  
User Weight Limitation:  
Please note that there is a weight limitation for this product. If you weigh more than 400lbs. it is not recommended that  
you use this product. Serious injury may occur if the user’s weight exceeds the limit shown here. This product is not  
intended to support users whose weight exceeds this limit.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5
EVO 3i MOTORIZED TREADMILL  
HARDWARE COMPARISON CHART  
Hardware chart:  
For your convenience, we have identified the hardware used in the assembly of this product. This chart is provided to help  
you identify those items that may be unfamiliar to you.  
NO. DESCRIPTION  
QTY.  
3
M6 x 10mm Screw  
M8 x 10mm Bolt  
#8 x 19mm Screw  
#8 x 25mm Screw  
M8 x 25mm Bolt  
Plastic Bracket  
4
5
4
10  
11  
19  
96  
97  
A
14  
12  
4
2
M6 x 20mm Screw  
5mm Wrench  
2
1
B
Wrench  
1
C
5/6mm Allen Wrench  
1
MILLIMETERS  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6
EVO 3i MOTORIZED TREADMILL  
PARTS LIST  
No. Description  
Qty. Order No.  
No. Description  
Qty. Order No.  
1
Computer  
1
EVO3i-01  
EVO3i-02  
EVO3i-03  
EVO3i-04  
EVO3i-05  
EVO3i-06  
EVO3i-07  
EVO3i-08  
EVO3i-09  
EVO3i-10  
EVO3i-11  
EVO3i-12  
EVO3i-13  
EVO3i-14  
EVO3i-15  
EVO3i-16  
EVO3i-17  
EVO3i-18  
EVO3i-19  
EVO3i-20  
EVO3i-21  
EVO3i-22  
EVO3i-23  
EVO3i-24  
EVO3i-25  
EVO3i-26  
EVO3i-27  
EVO3i-28  
EVO3i-29  
30  
31  
32  
33  
34  
35  
36  
37  
38  
39  
40  
41  
42  
43  
44  
45  
46  
47  
48  
49  
50  
51  
52  
53  
54  
55  
56  
57  
58  
Transport Wheel Base  
M10 x 60mm Bolt  
2
2
4
1
1
2
1
1
1
1
1
1
2
2
1
1
2
1
1
1
1
8
10  
1
10  
9
2
2
1
EVO3i-30  
EVO3i-31  
EVO3i-32  
EVO3i-33  
EVO3i-34  
EVO3i-35  
EVO3i-36  
EVO3i-37  
EVO3i-38  
EVO3i-39  
EVO3i-40  
EVO3i-41  
EVO3i-42  
EVO3i-43  
EVO3i-44  
EVO3i-45  
EVO3i-46  
EVO3i-47  
EVO3i-48  
EVO3i-49  
EVO3i-50  
EVO3i-51  
EVO3i-52  
EVO3i-53  
EVO3i-54  
EVO3i-55  
EVO3i-56  
EVO3i-57  
EVO3i-58  
2
Safety Key  
1
3
M6 x 10mm Screw  
Console Support Tube  
4
Bushing  
Transport Wheel Bracket -  
4
1
Left  
Transport Wheel Bracket -  
5
M8 x 10mm Bolt  
Handlebar Rear End Cap –  
Left #1  
Handlebar Rear End Cap –  
Left #2  
Handlebar Rear End Cap –  
Right #1  
Handlebar Rear End Cap –  
4
Right  
6
1
Transport Wheel  
Upright Plastic Shroud - Left  
7
1
#1  
Upright Plastic Shroud - Left  
8
1
#2  
Upright Plastic Shroud -  
9
1
Right #2  
Right #2  
Upright Plastic Shroud -  
Right #1  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
#8 x 19mm Screw  
14  
16  
1
#8 x 25mm Screw  
Handlebar - Left  
Handlebar - Right  
Hand Pulse Sensor  
Handlebar Front End Cap  
M8 x 15mm Screw  
Left Upright  
Side Cover - Left  
Side Cover - Right  
Cushion  
1
2
M6 x 55mm Bolt  
Cushion  
2
2
Motor Hood  
1
#8 x 50mm Screw  
Side Rail - Left  
Deck End Cap - Left  
Side Rail - Right  
Deck End Cap - Right  
Rail Guide  
Right Upright  
1
M8 x 25mm Bolt  
M14 x 113 Bolt  
4
2
Bushing  
4
Power Switch Set  
M5 x 10mm Screw  
1
2
M8 x 25mm Screw  
Running Deck  
Deck Cushion  
M10 x 35mm Bolt  
M5 x 12mm Screw  
Clip  
Base Frame  
Running Deck Fixed Tube  
Sleeve  
1
2
Level Adjuster  
Cushion  
4
2
6 x 13mm Washer  
# 8 x 15mm Screw  
11  
28  
Elevation Motor  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7
EVO 3i MOTORIZED TREADMILL  
PARTS LIST  
No. Description  
M10 x 63mm Hex Head Bolt  
Qty. Order No.  
No. Description  
Qty. Order No.  
Elevation Support Tube  
59  
60  
61  
62  
63  
64  
65  
66  
67  
68  
69  
70  
71  
72  
73  
74  
75  
76  
77  
78  
79  
80  
81  
82  
83  
84  
85  
86  
87  
88  
1
5
2
1
1
2
12  
2
1
1
1
1
1
1
1
3
1
1
1
1
1
2
2
2
4
1
1
2
2
1
EVO3i-59  
EVO3i-60  
EVO3i-61  
EVO3i-62  
EVO3i-63  
EVO3i-64  
EVO3i-65  
EVO3i-66  
EVO3i-67  
EVO3i-68  
EVO3i-69  
EVO3i-70  
EVO3i-71  
EVO3i-72  
EVO3i-73  
EVO3i-74  
EVO3i-75  
EVO3i-76  
EVO3i-77  
EVO3i-78  
EVO3i-79  
EVO3i-80  
EVO3i-81  
EVO3i-82  
EVO3i-83  
EVO3i-84  
EVO3i-85  
EVO3i-86  
EVO3i-87  
EVO3i-88  
89  
90  
91  
92  
93  
94  
95  
96  
97  
1
EVO3i-89  
EVO3i-90  
EVO3i-91  
EVO3i-92  
EVO3i-93  
EVO3i-94  
EVO3i-95  
EVO3i-96  
EVO3i-97  
Cover - Left  
Elevation Support Tube  
M10 Nylon Nut  
1
Cover - Right  
Washer  
Elevation Support  
1
Rubber Cushion  
Motor Belly Pan  
# 8 x 35mm Screw  
M8 Nut  
1
M8 x 135mm Bolt  
M8 x 15 Screw  
4
10  
1
8x15XT2.0 Spring Washer  
8 x 16mm Washer  
M10 x 136mm Hex Head Bolt  
Motor Bracket  
Running Belt  
Plastic Bracket  
M6 x 20mm Screw  
2
2
Driving Motor  
Motor Drive Belt  
Front Roller with Fly Wheel  
Front Roller Shaft  
Micro Switch  
M6 x 70mm Bolt  
Deck Frame  
Motor Hood Side Cover - Right  
Motor Hood Side Cover - Left  
Frame Side Cover - Right  
Frame Side Cover - Left  
Plastic Clamp - Top  
Plastic Clamp - Bottom  
Bracket  
M8 x 19mm Allen Head Bolt  
Rear Roller  
Rear Roller Shaft  
M8 x 43mm Bolt  
Deck Wheel  
Running Deck Fixed Tube  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8
EVO 3i MOTORIZED TREADMILL  
PARTS DIAGRAM  
A MAJORITY OF THE PARTS SHOWN HERE HAVE BEEN PREASSEMBLED AT THE FACTORY.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9
EVO 3i MOTORIZED TREADMILL  
PARTS DIAGRAM  
A MAJORITY OF THE PARTS SHOWN HERE HAVE BEEN PREASSEMBLED AT THE FACTORY.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
10  
EVO 3i MOTORIZED TREADMILL  
ASSEMBLY  
STEP 1:  
Remove your treadmill from the carton and place it on the floor in an open area as shown in FIG-1.  
Attach the Left Upright (17) and Right Upright (18) to the Base Frame (24) as shown and secure in place using two M6 x  
55mm Bolts (43), two 6 x 13mm Washers (28) and four M8 x 25mm Allen Bolt (19).  
Download from Www.Somanuals.com. All Manuals Search And Download.  
11  
EVO 3i MOTORIZED TREADMILL  
ASSEMBLY  
STEP 2:  
Attach the Computer (1) to the Console Support Tube (4) using four M6 x 20mm Allen Head Bolts (3).  
Download from Www.Somanuals.com. All Manuals Search And Download.  
12  
EVO 3i MOTORIZED TREADMILL  
ASSEMBLY  
STEP 3:  
Rotate the Console Support Tube (4) to the correct position and secure with M5 x 12mm Screw (56).  
Download from Www.Somanuals.com. All Manuals Search And Download.  
13  
EVO 3i MOTORIZED TREADMILL  
ASSEMBLY  
STEP 4:  
Attach the Upright Plastic Shroud – Left #1 (36) and Upright Plastic Shroud – Left #2 (37) to the Left Upright (17) and secure  
with five #8 x 25mm Screws (11) and four #8 x 19mm Screws (10). Repeat this procedure on Right Upright (18) with Upright  
Plastic Shroud – Right #2 (38) and Upright Plastic Shroud – Right #1 (39).  
Download from Www.Somanuals.com. All Manuals Search And Download.  
14  
EVO 3i MOTORIZED TREADMILL  
ASSEMBLY  
STEP 5:  
First connect the wires between the Left Handlebar (12) and Left Upright (17) as shown, then attach the Left Handlebar (12)  
to the Left Upright (17) using two M8 x 10mm Bolts (5). Repeat this procedure for the Right Handlebar (13) and Right Upright  
(18).  
Download from Www.Somanuals.com. All Manuals Search And Download.  
15  
EVO 3i MOTORIZED TREADMILL  
ASSEMBLY  
STEP 6:  
Attach the Handlebar Rear End Cap – Left #1 (6) to the Handlebar Rear End Cap – Left #2 (7) over the Left Upright (17) and  
secure in place using two #8 x 19mm Screws (10) and two #8 x 25mm Screws (11). Attach the Handlebar Rear End Cap –  
Right #2 (9) to the Handlebar Rear End Cap – Right #1 (8) over the Right Upright (18) and secure in place using two #8 x  
19mm Screws (10) and two #8 x 25mm Screws (11).  
Download from Www.Somanuals.com. All Manuals Search And Download.  
16  
EVO 3i MOTORIZED TREADMILL  
TRANSPORT INSTRUCTIONS  
How to transport the treadmill:  
1. To move the treadmill you will need to first flip  
out the Right and Left Transport Wheel Brackets  
(34 and 33) located on the underside of the Left  
and Right Uprights (17 and 18). You may need  
to tilt the treadmill to one side in order to access  
the wheels. Be careful when tilting the treadmill  
because it is heavy. You may need the  
assistance of another person to do this.  
2. Be sure both Transport Wheel Brackets (34 and  
33) are flipped down and resting firmly on the  
floor as shown in drawing 2.  
3. Carefully lift the treadmill up slightly from the rear  
and roll it to a desired position. Flip the  
Transport Wheel Brackets (34 and 33) back up  
into their stored position. Follow the instructions  
on the STABILIZER ADJUSTMENT page in this  
manual to level the frame to the floor.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
17  
EVO 3i MOTORIZED TREADMILL  
LEVEL ADJUSTMENT  
LEVEL ADJUSTMENT:  
Uneven flooring could cause the SPRING KNOBS not to engage and thus prevent the EVO3i from inclining.  
To adjust the levelers follow these instructions:  
You will need someone to help you with this procedure, as you will need to tip the treadmill on its side.  
Tip the treadmill to the left/right. You will then see the LEVEL ADJUSTERS. These will need to be screwed either in or out  
to level the treadmill. Repeat for the other side. It may help to use a spirit level when adjusting the level on your treadmill.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
18  
EVO 3i MOTORIZED TREADMILL  
MAINTENANCE  
HOW TO MAINTAIN THE EVO 3i TREADMILL:  
Proper maintenance is very important to ensure your treadmill is always in top working condition. Improper maintenance  
could cause damage or shorten the life of your treadmill and exceed the LIMITED WARRANTY coverage.  
?? Important: Never use abrasives or solvents to clean the treadmill. To prevent damage to the computer, keep liquids  
away and keep it out of direct sunlight.  
?? Inspect and tighten all parts of the treadmill regularly. Replace any worn parts immediately.  
BELT ADJUSTMENT:  
Belt adjustment and tension performs two functions: adjustment for tension and centering. The running belt has been  
adjusted properly at the factory. However transportation, uneven flooring or other unpredicted reasons could cause the belt to  
shift off center resulting in the belt rubbing with the plastic side rail or end caps and possibly causing damage. To adjust the  
belt back to it’s proper position please follow the directions below:  
?? Walking belt has shifted to the left: First unplug the power cord from the surge protector. Using the hex key  
provided, turn the left rear roller adjustment bolt 1/4 turn in the clockwise direction. Plug the power cord back into  
the surge protector and run the treadmill at 2.5 mph. You should see the belt start to correct itself, moving back  
towards the center. Repeat the above procedure until the walking belt is centered. It may be necessary to set  
walking belt tension once you have completed this procedure if the belt feels like it is slipping while walking. Refer  
below to the "Walking belt slipping" instructions.  
?? Walking belt has shifted to the right: First unplug the power cord from the surge protector. Using the hex key  
provided, turn the right rear roller adjustment bolt 1/4 turn in the clockwise direction. Plug the power cord back into  
the surge protector and run the treadmill at 2.5 mph. You should see the belt start to correct itself, moving back  
towards the center. Repeat the above procedure until the walking belt is centered. It may be necessary to set  
walking belt tension once you have completed this procedure if the belt feels like it is slipping while walking. Refer  
below to the "Walking belt slipping" instructions.  
?? Walking belt is slipping: First unplug the power cord from the surge protector. Using the hex key provided, turn  
both the left and right rear roller adjustment bolts the same distance, usually a 1/4 turn in the clockwise direction.  
Plug the power cord back into the surge protector and run the treadmill at 2.5 mph. You should now walk on the belt  
to determine if the belt is still slipping. Repeat the above procedure until the walking belt is not slipping. The tension  
should be just tight enough not to slip.  
WARNING! Do not over tighten rollers! This will cause premature roller bearing failure!  
Right and left tension bolts are located at the rear of the treadmill.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
19  
EVO 3i MOTORIZED TREADMILL  
MAINTENANCE  
CLEANING:  
Routine cleaning of your treadmill will extend the product's life.  
?? Warning: To prevent electrical shock, be sure the power to the treadmill is OFF and the power cord is unplugged  
from the wall electrical outlet before attempting any cleaning or maintenance.  
?? Important: Never use abrasives or solvents to clean the treadmill. To prevent damage to the computer, keep  
liquids away and keep it out of direct sunlight.  
?? After each workout: Wipe off the console and other treadmill surfaces with a clean, water dampened soft cloth to  
remove excess perspiration.  
?? Weekly: Use of a treadmill mat is recommended for ease of cleaning. Dirt from your shoes contacts the belt and  
eventually makes it to underneath the treadmill. Vacuum underneath treadmill once a week.  
DECK LUBRICATION:  
The walking belt has been pre-lubricated at the factory. However, it is recommended that the walking board be checked  
periodically for lubrication to ensure optimal treadmill performance. Your treadmill should not have to be lubricated usually  
within the first year or 500 hours of use. For service call your local EVO dealer or contact us directly at 888-800-1167.  
Every 3 months of operation lift the sides of the walking belt and feel the top surface of the walking board as far as you can  
reach. If you feel signs of silicone, no further lubrication is required. If it feels dry to the touch, follow the instructions below.  
Please use Lube 'N Walk (can be purchased from your dealer or call the number on the front of the manual), or a non-  
petroleum based silicone such as "Napa 8300" (available at most stores).  
To apply lubricant to the walking belt:  
1. Position the walking belt so that the seam is located on top and in center of the walking board.  
2. Insert the spray nozzle into the spray head of the lubricant can.  
3. While lifting the side of the walking belt, position the spray nozzle between the walking belt and the board  
approximately 6" from the front of the treadmill. Apply the silicone spray to the walking board, moving from the front  
of the treadmill to the rear. Repeat this on the other side of the belt. Spray approximately 4 seconds on each side.  
4. Allow the silicone to "set" for 1 minute before using the treadmill.  
Spray lubricant from front to back.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
20  
EVO 3i MOTORIZED TREADMILL  
WARRANTY  
This warranty covers all parts including frame, electronics and wear parts for a lifetime. Labor costs under this warranty are  
covered for a period of one year from the date of purchase. If used in a commercial setting the warranty will change to cover  
three (3) years on all parts and one (1) year on labor. Labor will be provided by an approved Smooth Fitness reseller, or at  
the discretion of Smooth fitness, through an approved independent service agent.  
Conditions Of Warranty  
This warranty is valid only for the original purchaser and is not transferable. A copy of the original purchase receipt will be  
required to obtain warranty parts and/or service. As a condition of this warranty, Smooth Fitness requires that the EVO  
treadmills be lubricated on the belt and deck in accordance with the manufacturer's maintenance requirements, and using  
lubrication in conformity with the specifications provided by the manufacturer. Customer is required to maintain records to  
establish compliance with maintenance requirements. Smooth Fitness will not be responsible for repair or replacement of any  
part damaged or destroyed due to misuse, failure to properly maintain, and/or abuse.  
Remedies for Parts and Service:  
Smooth Fitness may at its discretion, choose to provide any of the following parts or repair options. In the event that a part is  
determined in need of replacement, upon receipt of the part by Smooth Fitness, Smooth Fitness may send out the part by  
UPS ground or another such carrier directly to the customer's home. The customer is responsible for the cost of sending the  
part to Smooth Fitness. For one year from the date of purchase, labor will be provided by a Smooth Fitness dealer or service  
agent free of charge. After that time, the customer may either replace the component, or hire the dealer/service agent to  
provide the labor at an additional cost. If Smooth Fitness in its sole discretion determines that the treadmill cannot or should  
not be repaired, it may decide to purchase the unit for the residual value in accordance with the following: 25% of retail  
purchase price after 5 years, 15% after 10 years, 5% after 15 years.  
Unit has a labor warranty of 1 year from date of installation.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
21  
EVO 3i MOTORIZED TREADMILL  
IMPORTANT STEPS  
Warning:  
Before using this product, please consult your personal physician for a complete physical examination. Frequent and  
strenuous exercise should be approved by your doctor first. If any discomfort should result from your use of this product, stop  
exercising and consult your doctor. Proper usage of this product is essential. Please read your manual carefully before  
exercising.  
Please keep all children away from the equipment during use and when equipment is unattended.  
Always wear appropriate clothing, including athletic shoes, when exercising. Do not wear loose clothing that could become  
caught during exercising.  
Make sure that all bolts and nuts are tightened when equipment is in use. Periodic maintenance is required on all exercise  
equipment to keep it in good condition.  
Before beginning:  
How you begin your exercise program depends on your physical condition. If you have been inactive for several years, or  
are severely overweight, you must start slowly and increase your time gradually, a few minutes per week.  
Initially you may be able to exercise only for a few minutes in your target zone. However, your aerobic fitness will improve  
over the next six to eight weeks. Don’t be discouraged if it takes longer. It’s important to work at your own pace. Ultimately,  
you’ll be able to exercise continuously for 30 minutes. And the better your aerobic fitness, the harder you will have to work to  
stay in your target zone. But remember these essentials:  
?? Contact your physician before starting a workout or training program. Have your doctor review your training and diet  
programs to advise you of a workout routine you should adopt.  
?? Begin your training program slowly with realistic goals that have been set by you and your doctor.  
?? Supplement your program with some type of aerobic exercise such as walking, jogging, swimming, dancing and/or  
bicycling. Monitor your pulse frequently. If you do not have an electronic heart rate monitor, have your physician  
show you the proper way to manually check your pulse by using your wrist or neck. Establish your target heart rate  
based on your age and condition.  
?? Drink plenty of fluids during the course of your routine. You must replace the water content lost from excessive  
exercising to avoid dehydration. Avoid drinking large amounts of cold liquids. Fluids should be at room temperature  
when consumed.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
22  
EVO 3i MOTORIZED TREADMILL  
TARGET HEART RATE  
Finding your pulse:  
To make sure your heart is beating in its target zone, you’ll need to know how to monitor your heart rate. The easiest way is  
to feel the pulse in the carotid artery on either side of your neck, between the windpipe and the large neck muscles. Count  
the number of beats in ten seconds, and then multiply that number by six. This gives you the number of beats per minute.  
How fast should your heart beat during aerobic exercise? Fast enough to reach and stay in its “target zone,” a range of beats  
per minute that is largely determined by your age and physical condition. To determine your target zone, consult the chart  
we have provided.  
FIND YOUR TARGET HEART RATE  
200  
180  
160  
140  
120  
100  
80  
20  
25  
30  
35  
40  
45  
50  
55  
60  
65  
70  
AGE IN YEARS  
ADVANCED: Sports, athletic conditioning or interval training  
FITNESS: Optimal training, aerobic or cardiovascular  
HEALTH: Beginner, low intensity with long duration produces fat burning  
Aerobic exercise:  
Is any sustained activity that sends oxygen to your muscles via your heart and lungs. It will improve the fitness of your lungs  
and heart: your body’s most important muscle. Aerobic fitness is promoted by any activity that uses your large muscle  
groups - arms, legs or buttocks, for example. Your heart beats quickly and you breathe deeply. An aerobic exercise should  
be part of your entire exercise routine.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
23  
EVO 3i MOTORIZED TREADMILL  
MUSCLE CHART  
Targeted muscle groups:  
The exercise routine that is performed on this product will develop primarily lower body muscle groups. These muscle groups  
are shown in gray color on the chart below.  
Shoulder muscles  
Bicep muscle  
A
C
E
G
I
B
D
F
H
J
Pectoral muscles  
Abdominal muscles  
Quadricep muscles  
Trapezius muscles  
Back muscles  
Forearm muscles  
Calf muscles  
Tricep muscles  
Gluteal muscles  
K
L
Hamstring muscles  
Download from Www.Somanuals.com. All Manuals Search And Download.  
24  
EVO 3i MOTORIZED TREADMILL  
STRETCHING ROUTINE  
Warm up and cool down:  
A successful exercise program consists of a warm-up, aerobic exercise, and a cool-down. Do the entire program at least two  
and preferably three times a week, resting for a day between workouts. After several months, you can increase your  
workouts to four or five times per week.  
Warming up is an important part of your workout, and should begin every session. It prepares your body for more strenuous  
exercise by heating up and stretching out your muscles, increasing your circulation and pulse rate, and delivering more  
oxygen to your muscles. At the end of your workout, repeat these exercises to reduce sore muscle problems. We suggest  
the warm-up and cool-down exercises on the following pages:  
Toe Touch:  
Slowly bend forward from your waist, letting your back and shoulders relax as you  
stretch toward your toes. Reach down as far as you can and hold for 15 counts.  
Shoulder Lift:  
Lift your right shoulder up toward your ear for one count. Then lift your left  
shoulder up for one count as you lower your right shoulder.  
Head Roll:  
Rotate your head to the right for one count, feeling the stretch up the left side of  
your neck. Next, rotate your head back for one count, stretching your chin to the  
ceiling and letting your mouth open. Rotate your head to the left for one count,  
and finally, drop your head to your chest for one count.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
25  
EVO 3i MOTORIZED TREADMILL  
STRETCHING ROUTINE  
Hamstring Stretch:  
Sit with your right leg extended. Rest the sole of your left foot against your right  
inner thigh. Stretch toward your toe as far as possible. Hold for 15 counts. Relax  
and then repeat with left leg extended.  
Inner Thigh Stretch:  
Sit with the soles of your feet together with your knees pointing outward. Pull your  
feet as close into your groin as possible. Gently push your knees towards the  
floor. Hold for 15 counts.  
Side Stretch:  
Open your arms to the side and continue lifting them until they are over your head.  
Reach your right arm as far upward toward the ceiling as you can for one count.  
Feel the stretch up your right side. Repeat this action with your left arm.  
Calf-Achilles Stretch:  
Lean against a wall with your left leg in front of the right and your arms forward.  
Keep your right leg straight and the left foot on the floor; then bend the left leg and  
lean forward by moving your hips toward the wall. Hold, and then repeat on the  
other side for 15 counts.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
26  
EVO 3i MOTORIZED TREADMILL  
TROUBLESHOOTING  
Troubleshooting  
NOTE: Do not touch any internal electric wires without consulting the manufacturer.  
Treadmill will not start:  
1. Make sure the power cord is plugged into a surge protector, the surge protector is plugged into a properly grounded outlet  
and the surge protector is turned on (refer to the Power Requirements section in this manual).  
2. Check the circuit breaker reset switch located on the front of the treadmill. Turn the power off, wait 5 minutes then press  
the rest switch.  
3. Check the house electrical breaker box and the circuit breaker for the room the treadmill is located in. If it has tripped,  
reset or have an electrician replace the breaker in home.  
4. Have an electrician check for inadequate voltage at the outlet.  
Treadmill looses power during use:  
1. Check the circuit breaker reset switch located on the front of the treadmill. Turn the power off, wait 5 minutes then press  
the rest switch.  
If the treadmill still will not operate, please call your local EVO dealer or contact us directly at 888-800-1167.  
2. Check the house electrical breaker box and the circuit breaker for the room the treadmill is located in. If it has tripped,  
reset or have an electrician replace the breaker in home.  
Treadmill walking belt slows during use:  
1. Check to make sure the treadmill is securely plugged into an UL-listed surge protector, rated at 15 amps, with a 14-guage  
cord of five feet or less and the surge protector is securely plugged into the outlet. If the treadmill still will not operate, please  
call your local EVO dealer or contact us directly at 888-800-1167.  
Treadmill walking belt slips or is not centered on rear roller:  
Refer to the Belt Adjustment section of this manual. If you require additional assistance please call your local EVO dealer or  
contact us directly at 888-800-1167.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Smooth Fitness  
112 Gaither Drive  
Mt. Laurel, NJ 08054  
Toll Free Customer Service:  
1.888.800.1167  
Website:  
Copyright © 2003  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Craftsman Blower 35879476 User Manual
Craftsman Saw 3152121 User Manual
Creative Digital Camera 3200Z User Manual
Cub Cadet Lawn Mower SLT X1050 SLTX1054 User Manual
Curtis Clock Radio SRCD247 User Manual
Curtis Home Theater System DVD5091 User Manual
Curtis Speaker System RCD 637 User Manual
CyberData Network Card Wall Mount Adapter User Manual
Delta Electronics Network Card VFD PU06 User Manual
FEIN Power Tools Drill ASze 648a User Manual