Pub. 988-0143-881
www.eaglesonar.com
Mapping GPS Receiver
Installation and Operation
Instructions
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Section 1: Read Me First!............................................................... 1
Capabilities and Specifications: IntelliMap® 640c............................ 2
How GPS Works ................................................................................. 4
Introduction to GPS and WAAS......................................................... 6
How to use this manual: typographical conventions ........................ 8
Arrow Keys...................................................................................... 8
Keyboard.......................................................................................... 8
Menu Commands ............................................................................ 8
Instructions = Menu Sequences ..................................................... 8
Section 2: Installation & Accessories....................................... 11
Preparations...................................................................................... 11
GPS Antenna/Receiver Module Installation ................................... 11
Power Connections ........................................................................... 12
NMEA Cable Connections................................................................ 14
Mounting the Unit: Bracket, In-Dash or Portable.......................... 15
Bracket Installation...................................................................... 16
In-Dash Installation...................................................................... 17
Portable Installation..................................................................... 18
MMC or SD Card Memory Card Installation.................................. 19
To add an MMC or SD Card......................................................... 20
Section 3: Basic GPS Operations............................................... 23
Keyboard ........................................................................................... 23
Power/lights on and off..................................................................... 24
Main Menu........................................................................................ 24
Pages ................................................................................................. 26
Satellite Status Page .................................................................... 26
Navigation Page............................................................................ 28
Map Page....................................................................................... 30
Background map vs. MapCreate map content............................. 32
Resize Window command ............................................................. 34
Basic GPS Quick Reference........................................................ 36
Find Your Current Position ............................................................. 37
Moving Around the Map: Zoom & Cursor Arrow Keys................... 37
Selecting Any Map Item with the Cursor........................................ 38
Searching .......................................................................................... 38
Set a Waypoint.................................................................................. 40
To create and save a Waypoint:.................................................... 41
Navigate To a Waypoint................................................................... 43
Set Man Overboard (MOB) Waypoint ............................................. 44
Navigate Back to MOB Waypoint.................................................... 44
Navigate to Cursor Position on Map................................................ 45
i
Download from Www.Somanuals.com. All Manuals Search And Download.
Navigate to a Point of Interest......................................................... 46
Creating and Saving a Trail............................................................. 46
To Save a Trail .............................................................................. 47
Displaying a Saved Trail.................................................................. 48
To turn off trail display:................................................................ 48
To turn on trail display:................................................................ 48
Navigating Trails.............................................................................. 48
Visual Trailing .............................................................................. 49
Navigate a Trail ............................................................................ 49
Navigate a Back Trail................................................................... 51
Transfer Custom Maps and GPS Data Files................................... 52
Custom Maps:................................................................................ 52
GPS Data files:.............................................................................. 52
Cancel Navigation ............................................................................ 54
Section 4: Advanced GPS Operations...................................... 55
Find Distance From Current Position To Another Location.......... 55
Find Distance From Point to Point.................................................. 55
Icons .................................................................................................. 56
Create Icon on Map....................................................................... 56
Create Icon at Current Position................................................... 56
Delete an Icon................................................................................ 57
Navigate to an Icon....................................................................... 57
Routes................................................................................................ 57
Create and Save a Route .............................................................. 58
Delete a Route............................................................................... 60
Edit a Route Name........................................................................ 61
Edit Route Waypoints................................................................... 61
Navigate a Route........................................................................... 62
Navigate a Route in Reverse ........................................................ 62
Trails ................................................................................................. 63
Delete a Trail................................................................................. 63
Edit a Trail.................................................................................... 63
Utilities ............................................................................................. 65
Alarm Clock................................................................................... 65
Sun/Moon Rise & Set Calculator.................................................. 65
Trip Calculator.............................................................................. 65
Trip Down Timer........................................................................... 65
Trip Up Timer ............................................................................... 65
Waypoints ......................................................................................... 65
Delete a Waypoint......................................................................... 65
Delete a Waypoint from the map ................................................. 65
Edit a Waypoint ............................................................................ 65
Waypoint Symbol .......................................................................... 66
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
Waypoint Position......................................................................... 66
Selecting a Waypoint .................................................................... 66
Set a Waypoint by Average Position............................................ 66
Set a Waypoint by Projecting a Position...................................... 67
Section 5: System & GPS Setup Options.................................. 69
Alarms............................................................................................... 69
To change alarm settings:............................................................. 69
Check MMC Files and Storage Space.............................................. 70
Communications Port Configuration............................................... 70
Configure NMEA .............................................................................. 71
Coordinate System Selection ........................................................... 72
To setup Loran TD:....................................................................... 73
Map Fix ............................................................................................. 73
To configure a map fix: ................................................................. 74
Customize Page Displays ................................................................. 75
Customize Satellite Status Page.................................................. 75
GPS Simulator.................................................................................. 76
To get to the GPS Simulator:........................................................ 76
Simulating Trail or Route Navigation ......................................... 76
Initialize GPS.................................................................................... 77
Map Auto Zoom................................................................................. 77
Map Data .......................................................................................... 78
Earth Map Detail.......................................................................... 78
Pop-up Map Information .............................................................. 78
Map Boundaries............................................................................ 78
Fill Water With White .................................................................. 79
Map Overlays (Range Rings; Lat/Long Grid) .............................. 79
Map Datum Selection....................................................................... 79
Map Detail Category Drawn............................................................ 80
Map Orientation ............................................................................... 81
NauticPath USA Marine Charts................................................... 82
Nautical Chart Notes.................................................................... 82
Port Information ........................................................................... 83
Tidal Current Information............................................................ 84
Tide Information ........................................................................... 86
Navionics Charts............................................................................. 87
Overlay Data..................................................................................... 88
To overlay information on your screen: ....................................... 89
To remove overlaid data: .............................................................. 90
To move overlaid data:.................................................................. 90
Pop-up Help ...................................................................................... 91
Reset Options.................................................................................... 92
Require WAAS.................................................................................. 92
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Screen Contrast and Brightness...................................................... 93
Set Language .................................................................................... 93
Set Local Time .................................................................................. 93
Show WAAS Alarm........................................................................... 94
Software Version Information.......................................................... 94
Sounds and Alarm Sound Styles...................................................... 95
Track Smoothing............................................................................... 96
Trail Options..................................................................................... 96
Delete All Trails............................................................................ 97
Trail Update Rate ......................................................................... 97
Delete Trail.................................................................................... 98
New Trail....................................................................................... 98
Trail Visibility and Other Trail Options...................................... 98
Transparency .................................................................................... 99
Units of Measure ............................................................................ 100
Section 6: Searching ................................................................... 101
Find Addresses ............................................................................... 102
Find Any Item Selected by Map Cursor ........................................ 104
Find Interstate Highway Exits...................................................... 104
Find Map Places or Points of Interest (POI) ................................. 106
Find Streets or Intersections ......................................................... 108
Find Waypoints............................................................................... 112
Section 7: Supplemental Material ........................................... 115
WARNING!
A CAREFUL NAVIGATOR NEVER RELIES ON ONLY ONE METHOD
TO OBTAIN POSITION INFORMATION.
CAUTION
When showing navigation data to a position (waypoint), a GPS unit will show
the shortest, most direct path to the waypoint. It provides navigation data to the
waypoint regardless of obstructions. Therefore, the prudent navigator will not
only take advantage of all available navigation tools when traveling to a way-
point, but will also visually check to make sure a clear, safe path to the waypoint
is always available.
WARNING!
When a GPS unit is used in a vehicle, the vehicle operator is solely re-
sponsible for operating the vehicle in a safe manner. Vehicle operators
must maintain full surveillance of all pertinent driving, boating or fly-
ing conditions at all times. An accident or collision resulting in damage
to property, personal injury or death could occur if the operator of a
GPS-equipped vehicle fails to pay full attention to travel conditions and
vehicle operation while the vehicle is in motion.
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 1: Read Me First!
How this manual can get you out on the road, fast!
Welcome to the exciting world of digital GPS! We know you're anxious
to begin navigating, but we have a favor to ask. Before you grab the
IntelliMap® 640c and begin installing it, please give us a moment or
two to explain how our manual can help you get the best performance
from your compact, wide-screen, mapping GPS receiver.
First, we want to thank you for buying an Eagle GPS unit. Whether
you're a first time user or a professional fisherman, you'll discover that
your IntelliMap 640c is easy to use, yet capable of handling demanding
navigation tasks. When you team your unit with our custom mapping
software MapCreate 6, you have an incredible combination. You won't
find another GPS unit with this much power and this many features for
this price!
Our goal for this book is to get you on the road fast, with a minimum of
fuss. Like you, we'd rather spend more time navigating and less time
reading the manual!
So, we designed our book so that you don't have to read the whole thing
from front to back for the information you want. At the start (or end) of
each segment, we'll tell you what content is coming up next. If it's a
concept you're already familiar with, we'll show you how and where to
skip ahead for the next important topic. We've also made it easy to look
up any tips you may need from time to time. Here's how:
The manual is organized into 7 sections. This first section is an intro-
duction to Eagle GPS. It tells you the basics you need to know before
you can make the unit look around and tell you where you are.
Section 2 will help you install your unit. We'll show you how to get the
MultiMedia Card (MMC) correctly installed inside the unit. We'll also
tell you about some of the available accessories.
Section 3 covers Basic GPS Operation. It will show you how easy it is to
run the IntelliMap 640c, right out of the box. This section features a
one-page GPS Quick Reference. (If you've already jumped ahead
and figured out how to install the unit yourself, and you just
can't wait any longer, turn to the Quick Reference on page 36
and head for the road with your GPS unit!)
Section 3 contains short, easy-to-scan GPS lessons that follow one an-
other in chronological order. They're all you'll need to know to find your
way on the water or in the wilderness quickly.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
After you've learned the basics (or if you already have some GPS expe-
rience), you may want to try out some of the IntelliMap 640c's many
advanced navigation features. That brings us to Section 4, Advanced
GPS Operations. This section contains the rest of the unit's GPS com-
mand functions, organized in alphabetical order.
When you come to a GPS menu command on the IntelliMap 640c's screen,
you can look it up in the manual by skimming over the table of contents,
just flipping through Section 3 or scanning through the command portion of
Section 4.
This unit is ready to use right out of the box, but you can fine tune and cus-
tomize its operation with dozens of options. We describe how to use general
system options along with GPS options in Section 5, System Setup and
GPS Setup Options. Section 5 is organized in alphabetical order.
In Section 6, we go into more detail on one of the IntelliMap 640c's most
remarkable capabilities — Searching. We'll introduce a search example
in the Basic GPS Operation section, but there are so many map items
you can search for, we had to give this function its own section in the
manual! For example, did you know this unit can look up business
phone numbers, functioning as a virtual Yellow Pages? We’ll show you
how in Section 6.
Finally, in Section 7, we offer Supplemental Material, including a list of
the GPS datums used, warranties and customer service information.
Now, if you're into the fine details, glance over the next segment on
specifications to see just how much GPS power your IntelliMap 640c con-
tains. It's important to us (and our power users), but, if you don't care
how many watts of power the unit has, or how many waypoints it can
store, skip ahead to important information on how our GPS works, on
page 4.
Capabilities and Specifications: IntelliMap® 640c
General
Display:............................ 5.0" (12.7 cm) diagonal 256-color TFT LCD;
programmable to viewing preference.
Resolution:...................... 640V x 480H pixel resolution; 307,200 total
pixels.
Backlighting:.................. Backlit screen and keypad with multiple
lighting levels for night use.
Input power:................... 10 to 15 volts DC.
Current drain: ............... With lights on: 700 ma.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Case size:......................... 5.4" H x 6.9" W x 3.4" D (13.8 x 17.6 x 8.6
cm); sealed and waterproof; suitable for
saltwater use.
MMC slots: ...................... One, with waterproof door (SD card
compatible).
Recording:........................MMC & SD cards for recording GPS trip de-
tails and displaying charts or custom maps.
Back-up memory:.......... Built-in memory stores GPS data for dec-
ades. User settings are stored when unit is
turned off.
Languages:...................... 10; menu languages selectable by user.
GPS
Receiver/antenna:......... External EGC-12W GPS/WAAS antennal
module .
Background map:.......... Built-in custom, detailed Eagle map. Con-
tains: enhanced detail of continental U.S.
and Hawaii. Includes more than 60,000 nav
aids and 10,000 wrecks/obstructions in
coastal and Great Lakes waters. Metro
areas, selected major streets/highways and
interstate exit services details included.
Custom mapping:.......... MapCreate 6 software optional; optional
plug and play LEI FreedomMaps offer the
same high-detail without the computer work
of MapCreate. Other plug and play mapping
options include Fishing Hot Spots,
LakeMaster Pro Maps, LEI NauticPath
charts and Navionics charts.
Mapping memory:......... Up to 2 gigabytes on one MMC (or SD) card.
Position updates: .......... Every second.
Position points: ............. 1,000 waypoints; 1,000 event marker icons.
Audible alarms: ............. Arrival/off-course/anchor.
Graphic symbols for
waypoints or event
marker icons:................. 42.
Routes:............................. 100, up to 100 waypoints per route.
Plot Trails:...................... 10 savable; up to 10,000 points per trail.
Zoom range:.................... 40 ranges; 0.02 to 4,000 miles.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE:
The above memory capacities refer only to the IntelliMap 640c's on-
board memory. The amount of GPS data you can record and save for
recall later is limited only by the number and size of MMC cards you
have.
NOTICE!
The storage temperature range for your IntelliMap 640c is from -4
degrees to +167 degrees Fahrenheit (-20 degrees to +75 degrees
Celsius). Extended storage in temperatures higher or lower than
specified will damage the liquid crystal display in your unit. This
type of damage is not covered by the warranty. For more informa-
tion, contact the factory's Customer Service Department; phone
numbers are listed on the last page of this manual.
How GPS Works
You'll navigate faster and easier if you understand how the IntelliMap
640c scans the sky to tell you where you are on the earth – and, where
you're going. But if you already have a working understanding of GPS
receivers and the GPS navigation system, skip on ahead to Section 2,
Installation & Accessories on page 11. If you're new to GPS, read on.
You can later impress your friends with your new-found knowledge.
First, think of your unit as a small but powerful computer. But don't
worry — we made it easy to use, so you don't need to be a computer ex-
pert to find your way! The IntelliMap 640c includes a keypad and a
screen with menus so you can tell it what to do. The screen also lets the
unit show your location on a moving map, as well as point the way to
your destination.
This gimbal-mounted IntelliMap 640c uses an external an-
tenna/receiver module, which makes the whole system work something
like your car radio. But instead of your favorite dance tunes, this re-
ceiver tunes in to a couple of dozen GPS satellites circling the earth. It
will also listen in to the WAAS satellites in orbit, but more about that
in the upcoming segment introducing you to GPS and WAAS.
Your unit listens to signals from as many satellites as it can "see" above
the horizon, eliminates the weakest signals, then computes its location
in relation to those satellites. Once the IntelliMap 640c figures its lati-
tude and longitude, it plots that position on the moving map shown on
the screen. The whole process takes place several times a second!
The performance doesn't stop there. Stored in the permanent memory
of each unit is a basic background map of the entire world. We lock it in
here at the factory — you can't change or erase this map.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
The background map is suitable for many navigation chores, but for
maximum accuracy and much more detail, you need our optional map-
making software, MapCreate 6, or one of our special plug-and-play
mapping cards. Some unit features — such as searching for businesses
and addresses — won't work without a custom MapCreate map. There
is so much detail in our background map and even more in MapCreate
that we'll describe their contents and differences in Section 3, Basic
GPS Operations, on page 36.
Another portion of the IntelliMap 640c's onboard memory is devoted to
recording GPS navigation information, which includes waypoints, event
marker icons, trails and routes. This lets you look back the way you came.
Think of this data storage like the hard drive memory in a computer or a
tape in a cassette tape recorder. You can save several different GPS data
files, erase 'em and record new ones, over and over again. Like any com-
puter file, these GPS Data Files (file format *.usr) can be shared be-
tween Eagle GPS or sonar/GPS units or even personal computers.
This IntelliMap 640c has one more thing in common with a personal
computer. Just as computers have a floppy disk drive for storing and ex-
changing files, the unit has a slot for an MMC (MultiMedia Card) or SD
card (Secure Digital card) flash memory card. These solid-state memory
devices are about the size of a postage stamp, but can hold data ranging
from 8 MB to 2 GB in size. (Compare that to a floppy disk's 1.44 MB ca-
pacity!) This unit uses all that MMC space for two key GPS purposes.
First, you can backup your onboard GPS Data Files by copying them to
the MMC. Since the MMC is removable (like a floppy disk or a cassette
tape), you can store these GPS Data Files on a personal computer
equipped with an MMC card reader. Or store them on a pocketful of
MMCs, if you don't have a computer. Our MapCreate mapping software
can save, edit or create its own GPS Data Files, which can be copied to the
MMC and then loaded from the MMC into the unit's memory. No matter
where they come from, GPS Data Files must be loaded from the MMC
into memory before the IntelliMap 640c can use them.
The other key GPS use for MMCs is storage of special high-detail, cus-
tom maps, which you can produce on your computer with our MapCre-
ate software. These MapCreate custom maps contain much greater de-
tail than the basic background map. These Custom Map Files (file
format *.lcm) can also be shared between Eagle GPS or sonar/GPS
units and personal computers.
This unit automatically reads Custom Map Files directly from the
MMC or SD card. To use a custom map, all you need to do is slide an
MMC containing a map into the IntelliMap 640c.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction to GPS and WAAS
Well, now you know the basics of how the unit does its work. You might
be ready to jump ahead to Section 2, Installation & Accessories, on page
11, so you can mount your IntelliMap 640c and plug in the power. Or
you might want to see how our text formatting makes the manual tuto-
rials easy to skim. If that's the case, move on to "How to Use This Man-
ual" on page 8. But, if you want to understand the current state of sat-
ellite navigation, look over this segment describing how GPS and its
new companion WAAS work together to get you where you're going.
The Global Positioning System (GPS) was launched July 17, 1995 by
the United States Department of Defense. It was designed as a 24-
hour-a-day, 365-days-a-year, all weather global navigation system for
the armed forces of the U.S. and its allies. Civilian use was also avail-
able at first, but it was less accurate because the military scrambled
the signal somewhat, using a process called Selective Availability (SA).
GPS proved so useful for civilian navigation that the federal govern-
ment discontinued SA on May 2, 2000, after the military developed
other methods to deny GPS service to enemy forces. Reliable accuracy
for civilian users jumped from 100 meters (330 feet) under SA to the
present level of 10 to 20 meters (about 30 to 60 feet.)
Twenty-four satellites orbit 10,900 nautical miles above the Earth, passing
overhead twice daily. A series of ground stations with precisely surveyed
locations controls the satellites and monitors their exact locations in the
sky. Each satellite broadcasts a low-power signal that identifies the satel-
lite and its position above the earth. Three of these satellites are spares,
unused until needed. The rest virtually guarantee that at least four satel-
lites are in view nearly anywhere on Earth at all times.
A minimum of three satellites are required to determine a 2D fix.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
The system requires signal reception from three satellites in order to
determine a position. This is called a 2D fix. It takes four satellites to
determine both position and elevation (your height above sea level —
also called altitude). This is called a 3D fix.
Remember, the unit must have a clear view of the satellites in order to
receive their signals. Unlike radio or television signals, GPS works at
very high frequencies. These signals can be easily blocked by trees,
buildings, an automobile roof, even your body.
Like most GPS receivers, this unit doesn’t have a compass or any other
navigation aid built inside. It relies solely on the signals from the sat-
ellites to calculate a position. Speed, direction of travel, and distance
are all calculated from position information. Therefore, in order for the
IntelliMap 640c to determine direction of travel, you must be moving
and the faster, the better. This is not to say that it won’t work at
walking or trolling speeds — it will. There will be more "wandering" of
the data shown on the display.
GPS alone is plenty accurate for route navigation, but the U.S. Federal
Aviation Administration has special aircraft navigation needs that go
beyond basic GPS. Consequently, the FAA has developed a program to
boost GPS performance with its Wide Area Augmentation System
(WAAS). The FAA commissioned the system on July 11, 2003.
WAAS is designed to increase GPS accuracy to within 7.6 meters verti-
cally and horizontally, but according to the FAA, it consistently comes
within 1-2 meters horizontally and 2-3 meters vertically. It does this by
broadcasting correction signals on GPS frequencies. Your unit auto-
matically receives both GPS and WAAS signals.
There are, however, some fringe areas of the U.S., including parts of
Alaska, that do not yet receive robust WAAS coverage. Continued
WAAS development is planned to extend WAAS coverage in the years
to come.
WAAS boosts the accuracy of land GPS navigation, but the system is
designed for aircraft. The satellites are in a fixed orbit around the
Equator, so they appear very low in the sky to someone on the ground
in North America. Aircraft and vessels on open water can get consis-
tently good WAAS reception, but terrain, foliage or even large man-
made structures can sometimes block the WAAS signal from ground
receivers.
You'll find that using your GPS receiver is both easy and amazingly
accurate. It’s easily the most accurate method of electronic navigation
available to the general public today. Remember that this receiver is
7
Download from Www.Somanuals.com. All Manuals Search And Download.
only a tool. Always have another method of navigation available, such
as a map or chart and a compass.
Also remember that this unit will always show navigation information
in the shortest line from your present position to a waypoint, regardless
of terrain! It only calculates position, it can’t know what’s between you
and your destination, for example. It’s up to you to safely navigate
around obstacles, no matter how you’re using this product.
How to use this manual: typographical conventions
Many instructions are listed as numbered steps. The keypad and arrow
"keystrokes" appear as boldface type. So, if you're in a real hurry (or
just need a reminder), you can skim the instructions and pick out what
menu command to use by finding the boldface command text. The fol-
lowing paragraphs explain how to interpret the text formatting for
those commands and other instructions:
Arrow Keys
The arrow keys control the movement of dotted cross-hair lines on your
mapping screen called the cursor. The arrow keys help you move
around the menus so you can execute different commands. They are
represented by symbols like these, which denote the down arrow key,
the up arrow, the left arrow and the right arrow: ↓ ↑ ← →.
Keyboard
The other keys perform a variety of functions. When the text refers to a
key to press, the key is shown in bold, sans serif type. For example, the
"Enter/Icons" key is shown as ENT and the "Menu" key is shown as
MENU.
Menu Commands
a menu command or a menu option will appear in small capital letters,
in a bold sans serif type like this: ROUTE PLANNING. These indicate that
you are to select this command or option from a menu or take an action
of some kind with the menu item. Text that you may need to enter or
file names you need to select are show in italic type, such as trail name.
Instructions = Menu Sequences
Most functions you perform with this unit are described as a sequence
of key strokes and selecting menu commands. We've written them in a
condensed manner for quick and easy reading.
For example, instructions for navigating a trail would look like this:
1. From the Map Page, press MENU|MENU|↓ to MY TRAILS|ENT.
2. Press ↓ to Trail 1|ENT|→|↓ to NAVIGATE|ENT.
3. You are asked to wait while it converts the trail into a route.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
4. The wait message disappears and the IntelliMap 640c begins show-
ing navigation information along the trail. Now, begin moving and fol-
low your IntelliMap 640c.
Translated into complete English, step 1 above would mean: "Start on
the Map Page. Press the Menu key twice. Next, repeatedly press (or
press and hold) the down arrow key to scroll down the menu and select
(highlight) the My Trails menu command. Finally, press the Enter key."
Step 2 would mean: "Press the down arrow key repeatedly to scroll to
the trail named Trail 1, and press Enter. Next, press the right arrow
key and then the down arrow key to highlight the Navigate command,
then press Enter."
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2:
Installation & Accessories
Preparations
You can install the GPS system in some other order if you prefer, but
we recommend this installation sequence:
Caution:
You should read over this entire installation section before drill-
ing any holes in your vehicle or vessel!
1. Determine the approximate location for the GPS unit, so you can
plan how and where to route the cables for the antenna and power.
This will help you make sure you have enough cable length for the de-
sired configuration.
2. Determine the approximate location for the GPS antenna module
and its cable route.
4. Determine the location of your battery or other power connection,
along with the power cable route.
6. Install the GPS antenna and route the antenna cable to the GPS
unit.
7. Install the power cable and route it to the GPS unit.
8. Mount the GPS unit.
GPS Antenna/Receiver Module Installation
The IntelliMap 640c package includes the EGC-12w GPS module. This
device contains the IntelliMap 640c's external antenna and receiver for
GPS and WAAS signals. The antenna/receiver module comes with a 25-
foot extension cable. This module can be mounted on a flat surface,
pole, or an optional magnet is available for temporary mounting on any
ferrous surface.
EGC-12w Module, bottom view (left) and top view (right).
11
Download from Www.Somanuals.com. All Manuals Search And Download.
You need to select an antenna installation location that has a clear, un-
obstructed view of the sky. After the module is installed, route the cable
to the unit, plug it in the center socket on the back and your system is
ready to use. See the module's instruction sheet, publication part num-
ber 988-0148-371, for complete installation directions.
In an automobile, you may achieve good results by placing the external
antenna on the top of the dash or at the base of the windshield. A piece
of the rubber non-skid shelf liner material available in recreational ve-
hicle supply stores will help hold the antenna in place. This may not
work well if you have a cab-over design pickup truck camper or motor
home. If dashboard reception is poor, relocate the antenna module
elsewhere on the vehicle for a clearer view of the sky.
Power Connections
The IntelliMap 640c works from a 12-volt battery system. For the best
results, attach the power cable directly to the battery. You can attach
the power cable to an accessory or power buss, but you might have
problems with electrical interference. Therefore, it's safer to go ahead
and attach the power cable directly to the battery.
CAUTION:
When using the unit in a saltwater environment, we strongly rec-
ommend that you shut off the power supply to the power cable when
the unit is not in use. When the unit is turned off but still connected
to a power supply, electrolysis can occur in the power cable plug.
This may result in corrosion of the plug body along with the electri-
cal contacts in the cable and the unit's power socket.
In saltwater environments we recommend you connect the power
cable to the auxiliary power switch included in most boat designs.
If that results in electrical interference, or if such a switch is not
available, we recommend connecting direct to the battery and in-
stalling an inline switch. This will let you shut off power to the
power cable when the unit is not in use. When you are not using
the unit, you should always shut off power to the power cable, es-
pecially when the power cable is disconnected from the unit.
If possible, keep the power cable away from other boat wiring, espe-
cially the engine's wires. This will provide the best isolation from elec-
trical noise. If the cable is not long enough, splice #18 gauge wire onto
it. The power cable has two wires, red and black. Red is the positive
lead, black is negative or ground. Make sure to attach the in-line fuse
holder to the red lead as close to the power source as possible.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
For example, if you have to extend the power cable to the battery or
power buss, attach one end of the fuse holder directly to the battery or
power buss. This will protect both the unit and the power cable in the
event of a short. It uses a 3-amp fuse.
To unit
Optional power off switch for
saltwater installations
Red wire with
3 amp fuse
Black wire
12 volt
battery
Power connections for the IntelliMap 640c GPS unit.
WARNING:
This product must be independently fused with the en-
closed 3-amp fuse (or equivalent), even if you connect to
a fused accessory or power buss.
If a malfunction happens inside the unit, extensive dam-
age can occur if the enclosed fuse is not used. As with all
electrical devices, this unit could be damaged to a point
that it is not repairable and could even cause harm to the
user when not properly fused.
CAUTION:
Failure to use the enclosed 3-amp fuse will void your warranty! For
a replacement, use a type 3AG 3-amp fuse.
This unit has reverse polarity protection. No damage will occur if the
power wires are reversed. However, the unit will not work until the
wires are attached correctly.
An optional 8-foot, CA-4 external power cable with a cigarette lighter
adapter is available from Eagle.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear view of unit
Power Connector
GPS Connector
NMEA 0183
Com Port
Power cable
3-amp fuse
Com port
data wires
(three)
GPS antenna
module
12-volt battery
Cable connections.
NMEA Cable Connections
NMEA is a standard communications format for marine electronic
equipment. For example, an autopilot can connect to the NMEA inter-
face on the IntelliMap 640c and receive positioning information. The
IntelliMap 640c can exchange information with any device that trans-
mits or receives NMEA 0183 data.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
However, a communications cable is not available for the unit at this time.
If you need to create a NMEA 0183 connection consult customer service.
Service contact information can be found in the back of this manual.
NMEA Wiring
To exchange NMEA data, the IntelliMap 640c has one NMEA 0183 ver-
sion 2.0 communication port. Com port one (Com-1) can be used to re-
ceive NMEA format GPS data. The com port can also transmit NMEA
format GPS data to another device.
A data cable should contain three wires. Com-1 uses the yellow wire to
transmit, the orange wire to receive and the shield wire for signal
ground.
Orange (Receive)
NMEA Transmit
Com-1 to
IntelliMap 640c
To Other
GPS Receiver
Ground
Shield (Ground)
Com-1 wiring to receive NMEA position information
from some other GPS receiver.
Yellow (Transmit)
Shield (Ground)
NMEA Receive
Ground
To Other
Device
Com-1 to
IntelliMap 640c
Com-1 wiring to transmit NMEA position information
to another NMEA-compatible device.
Mounting the Unit: Bracket, In-Dash or Portable
You can install the IntelliMap 640c on the top of a dash with the sup-
plied gimbal bracket. It can also be installed in the dash or mounted on
a portable power supply.
If you use the supplied bracket, you may be interested in an optional
R-A-M bracket mounting system. This converts the unit's gimbal bracket
to a swivel mount, which can be used on the dash. R-A-M offers permanent
mounts and temporary mounts suitable for many vehicle types. See your
Eagle dealer or visit the LEI web site (www.lei-extras.com) for the latest
options; accessory ordering information is on the inside back cover of this
manual. For a complete look at the many mounting options, visit the RAM
web site at www.ram-mount.com.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional R-A-M mounting system.
Bracket Installation
Mount the IntelliMap 640c in any convenient location, provided there is
clearance behind the unit when it's tilted for the best viewing angle.
You should also make sure there is enough room behind the IntelliMap
640c to attach the power and GPS antenna/receiver module cables. A
drawing on the next page shows the dimensions of a gimbal-mounted
IntelliMap 640c.
Holes in the bracket's base allow wood screw or through-bolt mounting.
You may need to place a piece of plywood on the back side of thin fiber-
glass panels to reinforce the panel and secure the mounting hardware.
Front
Install the gimbal bracket. Orient the bracket so the arms slope
toward the front of your unit.
Drill a 1-inch (25.4 mm) hole in the dash for the power and antenna
cables. The best location for this hole is immediately under the gimbal
bracket location.
This way, the bracket can be installed so that it covers the hole, holds
the cables in position and results in a neat installation. Some custom-
ers, however, prefer to mount the bracket to the side of the cable hole
— it's a matter of personal preference.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
72.9
[2.87]
23.4
[0.92]
173.9
[6.85]
137.9
[5.43]
157.9
[6.22]
56.9
[2.24]
Millimeter
[Inch]
Front view (left) and side view (right) showing dimensions of the
IntelliMap 640c when mounted on gimbal bracket.
After drilling the hole, pass the antenna connector up through the hole
from under the dash. Pass the power cable's bare-wire end down
though the hole from the top.
If you wish, you can fill in the hole around the cables with a good marine
sealant compound. Some marine dealers stock cable hole covers to con-
ceal the opening. No matter what type of installation you prefer, be sure
to leave enough slack in the cables to allow tilting or swiveling the Intel-
liMap 640c. If you choose to fill in the hole, be sure to position the cables
against the rear edge of the hole as you apply the fill material.
Before positioning the bracket, be sure to hold the cables against the
rear edge of the hole. Then, slide the bracket over the hole and butt the
rear of the bracket base firmly against the cables, thus pinning them in
place against the side of the hole. Finally, fasten the bracket to the
dash. Attach the unit to the gimbal bracket using the supplied gimbal
knobs and washers.
In-Dash Installation
You can mount the IntelliMap 640c in the dash with an optional FM-5
In-Dash Adapter Kit. The kit includes mounting hardware, a template
for cutting the hole and an instruction sheet, part 988-0147-43.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
146.5
[5.76]
Top
R 7.9
[0.31]
In-Dash
Template
113.5
[4.46]
Millimeters
[Inches]
ALWAYS VERIFY DIMENSIONS
In-dash mounting template for the IntelliMap 640c, showing
dimensions. NOTE: The figure above is not printed to scale. a scaled
template (FM-5 In-Dash Adapter Kit instructions) is available for free
download from our web site, www.eaglegps.com.
Portable Installation
Like many Eagle products, the IntelliMap 640c is capable of portable
operation by using an optional portable power pack (PPP). The power
pack expands the uses for your GPS unit. The PPP makes it easy to
transfer your unit from a boat to a car, recreational vehicle, airplane or
other vehicle without drilling and mounting a second bracket. You can
use your unit in your own car or boat, then take it along when riding in
a friend's vehicle that's not equipped with GPS.
Most LEI portable power packs can be used with eight "D" cell alkaline
batteries. Some use an optional sealed, rechargeable battery. For in-
formation on the PPP for your unit, see the accessory ordering informa-
tion inside the back cover of this manual.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
"D" cell battery
Installing batteries in a typical portal power pack.
MMC or SD Card Memory Card Installation
Your IntelliMap 640c uses a MultiMedia Card to store information,
such as custom maps, waypoints, trails and other GPS data.
NOTE:
Throughout this manual, we will use the term MMC, but just re-
member that your unit can use an MMC or SD card to store data.
Both of these solid-state flash memory devices are about the size of a
postage stamp. An SD card is slightly thicker than an MMC. As this
manual went to press, MMCs and SD cards were available in various
storage capacities up to 2 gigabytes.
Additional MMC cards are available from LEI Extras, see ordering in-
formation inside the back cover of this manual. MMCs and SD cards
are also available at many camera and consumer electronics stores.
The MMC slot is located in a compartment on the front of the case. The
compartment door is located at the lower right corner. The following
figure shows a close-up with the door opened.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
MMC groove for card removal
Thumb
screw
Insert card face up,
this way
Memory card compartment with a 16 MB MMC card installed.
To remove an MMC
1. Open the card compartment door by unscrewing the thumb screw.
The screw should only be finger tight. If it was over-tightened, use a
thumbnail, a coin or a screwdriver to open the door.
2. Just press a finger against the label of the MMC and drag it from the
slot.
3. Close the compartment door and fasten the thumb screw finger tight.
To add an MMC or SD Card
1. Open the card compartment door.
2. Grasp the bottom of the MMC and push the top of the card into the
slot. Once the card is started, use your fingernails to slide it the rest of
the way to the left, until it is firmly seated in the slot.
3. Close the compartment door and fasten the thumb screw finger tight.
Other Accessories
Other accessories include MMC cards, MMC card readers and MapCre-
ate™ 6 custom mapping software for your computer. MMC card readers
are available in USB and parallel port versions.
If these accessories are not available from your dealer, see the acces-
sory ordering information on the inside back cover of this manual.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
MapCreate™ 6 CD-ROM (left) and MMC card reader for USB ports on
the right.
Now that you have your IntelliMap 640c installed, move on to Section
3, Basic GPS Operations. There, we'll present a series of step-by-step
tutorials to teach you the basics of GPS navigation.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 3:
Basic GPS Operations
This section addresses the unit's most basic GPS operations. The tuto-
rials presented in Sec. 3 follow a chronological order. Sec. 4, Advanced
GPS Operations, will discuss other more advanced functions and utili-
ties. Material in Sec. 4 is arranged in alphabetical order.
Before you turn on the unit and find where you are, it's a good idea to
learn about the different keys, the three Page screens and how they all
work together. BUT, if you just can't wait to get outside, turn to the
one-page Quick Reference on page 36.
Keyboard
4
9
7
6
1
8
2
3
5
MMC slot access door
IntelliMap 640c GPS unit Map Page, keyboard and access door for the
MMC slot.
1. PWR/LIGHT (Power & Light) – The PWR key turns the unit on and
off and activates the backlight.
2. PAGES – Pressing this and the ← → arrow keys (4) switches the
unit between the three different page screens. (Satellite Status Page,
Navigation Page and Map Page.) Each page represents one of the unit's
major operation modes.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
3. MENU – Press this key to show the menus and submenus, which
allow you to select a command or adjust a feature. This also accesses
search functions for streets, intersections, addresses and highway exits.
4. ARROW KEYS – These keys are used to navigate through the
menus, make menu selections and move the map cursor.
5. ENT/ICONS (Enter & Icons) – This key allows you to save data, ac-
cept values or execute menu commands. It is also used to create event
marker icons.
6. EXIT – The Exit key lets you return to the previous screen, clear
data or erase a menu.
7. WPT – (Waypoint) The Waypoint key is used to save and recall way-
points, search for waypoints and access the waypoint list. It also
launches the Point-of-Interest (POI) search menus and is involved in
some navigation functions.
8. ZOUT – (Zoom Out) – This key lets you zoom the screen out. This
lets you see a larger geographic area on the map. Less detail is seen as
you zoom out.
9. ZIN – (Zoom In) – This key lets you zoom the screen in. Zooming in
lets you see greater detail in a smaller geographic area on the map.
Power/lights on and off
To turn on the unit, press PWR. As the unit powers up, the Map Page is
displayed first. (To switch to another page, press PAGES|← or → to
Page Name|EXIT.)
To turn on the backlight, press PWR again. The unit has three backlight
levels to select from. Repeatedly pressing PWR will cycle through the
backlight settings and turn off the backlight.
Turn off the unit by pressing and holding the PWR key for 3 seconds.
Main Menu
The unit has a Main Menu, which contains some function commands and
some setup option commands. The tutorial lessons in this section will
deal only with functions, the basic commands that make the unit do
something. The GPS will work fine for these lessons right out of the box
with the factory default settings. But, if you want to learn about the
various options, see Sec. 5, System Setup and GPS Setup Options.
You can access the Main Menu from any of the three Page screens by
pressing MENU|MENU. To clear the menu screen and return to the page
display, press EXIT.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Main Menu.
The Main Menu commands and their functions are:
Screen command: changes the contrast or brightness of the display
screen.
Sounds command: enables or disables the sounds for key strokes and
alarms and sets the alarm style.
Transparency command: adjust the level of transparency for menus.
Alarms command: turns GPS alarms on or off and changes alarm
thresholds.
Route Planning command: used to plan, view or navigate a route.
My Trails command: shows, hides, creates and deletes plot trails. Also
used to navigate or backtrack a trail.
Cancel Navigation command: turns off the various navigation com-
mands. Used to stop navigating after you have reached your destina-
tion waypoint, Point of Interest or map cursor location; or after you
reach the end of a route or trail.
GPS Setup command: sets various GPS receiver options.
System Setup command: sets general configuration options.
Sun/Moon Calculations command: finds the rising and setting time
of the sun and the moon.
Trip Calculator command: shows trip status and statistics.
Timers command: controls the up timer, down timer and alarm clock
settings.
Browse MMC Files command: this allows you to view the installed
MMC card and the files it contains.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Pages
The unit has three Page displays that represent the three major oper-
ating modes. They are the Satellite Status Page, the Navigation Page
and Map Page. They are accessed by pressing the PAGES key, then us-
ing → or ← to select a Page. Exit the Pages Menu by pressing EXIT.
Pages Menu showing Map display options.
Satellite Status Page
The Satellite Status Page, shown in the following images, provides de-
tailed information on the status of the unit's satellite lock-on and posi-
tion acquisition. To get to the Satellite Status Page: Press the PAGES
key, then use → or ← to select STATUS. Leave the Pages Menu by press-
ing EXIT.
No matter what Page you are on, a flashing current position indica-
tor/question mark symbol and flashing GPS data displays indicate that
satellite lock has been lost and there is no position confirmed. The Sat-
ellite Status Page shows you the quality and accuracy of the current
satellite lock-on and position calculation.
WARNING:
Do not begin navigating with this unit until the numbers
have stopped flashing!
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Satellite Status Page. The first figure (left) indicates unit has not locked
on to any satellites and does not have a fix on its position. The second
figure (right) shows satellite lock-on with a 3D position acquired (lati-
tude, longitude and altitude), and WAAS reception.
This screen shows a graphical view of the satellites that are in view. Each
satellite is shown on the circular chart relative to your position. The point in
the center of the chart is directly overhead. The small inner ring represents
45° above the horizon and the large ring represents the horizon. North is at
the top of the screen. You can use this to see which satellites are obstructed
by obstacles in your immediate area if the unit is facing north.
The GPS receiver is tracking satellites that are in bold type. The re-
ceiver hasn't locked onto a satellite if the number is grayed out, there-
fore it isn't being used to solve the position.
Beneath the circular graph are the bar graphs, one for each satellite in
view. Since the unit has twelve channels, it can dedicate one channel
per visible satellite. The taller the bar on the graph, the better the unit
is receiving the signals from the satellite.
NOTE:
One of the data display options for the Satellite Status page is "Po-
sition Error" (horizontal position error), which can appear in one of
the page's data boxes. Position Error will show you the expected er-
ror from a benchmark location. In other words, if the Position Error
box shows 50 feet, then the position shown by the unit is estimated
to be within 50 feet of the actual location.
It also gives you an indicator of the fix quality the unit currently has.
The smaller the position error number, the better (and more accu-
rate) the fix is. If the position error flashes dashes, then the unit
hasn't locked onto the satellites, and the number shown isn't valid.
For details, see Customize Page Displays, on page 76.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
The Satellite Status Page has its own menu, which is used for setting
various options. Options and setup are discussed in Sec. 5. To access
the Satellite Status Page Menu, from the Status Page, press MENU.
Navigation Page
This screen has a compass rose that not only shows your direction of
travel, but also the direction to a recalled waypoint. To get to the Navi-
gation Page: Press PAGES|→ or ← to NAVIGATION|EXIT.
The navigation screen looks like the one below when you're not navi-
gating to a waypoint or following a route or trail. Your position is
shown by an arrow in the center of the screen. Your trail history, or
path you've just taken, is depicted by the line extending from the arrow.
The arrow pointing down at the top of the compass rose indicates the cur-
rent track (direction of travel) you are taking.
Track or compass heading indicator, showing direction of travel
Compass
rose
Trail line
Navigation
information
displays in
customizable
data boxes
Present
position
arrow
Traveling north and recording a trail on the Navigation page. The
page looks like this when the unit is not navigating to a waypoint, fol-
lowing a route or backtracking a trail.
When navigating to a waypoint, the Navigation screen looks like the
following figure. Your ground speed, track, distance and bearing to
waypoint, and course are all shown digitally on this screen.
NOTE:
Remember, when the Speed, Track and Position information dis-
plays are flashing, satellite lock has not been achieved and no posi-
tion fix has been determined. A question mark will also flash on the
present position arrow in the center of the compass rose.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Speed is the velocity you are making over the ground. If you prefer, you
can customize the Speed data box to display Closing Speed instead.
Closing Speed is also known as velocity made good. It's the speed that
you're making toward the waypoint. For instructions, see the Custom-
ize Page Displays entry in Sec. 5.
Track is the heading, or the current direction you are actually travel-
ing. Bearing is the direction of a line-of-sight from your present position
to the destination. No matter what direction you are steering, the
Bearing window shows the compass direction straight to the destina-
tion from your location at the moment. Distance shows how far it is to
the waypoint you're navigating toward.
The Off Course window shows the current cross track error. This shows
the distance you are off-course to the side of the desired course line. The
course line is an imaginary line drawn from your position when you
started navigating to the destination waypoint. The course line is shown on
the Navigation Page screen and the Map Page screen as a dotted line.
Heading arrow
Red course line
Magenta
trail line
Bearing
arrow
Cross track
error range
(off course
indicator)
Navigation
information
displays
Destination
name
in data boxes
Navigation Page, going to a waypoint while creating a new trail.
The cross track error range is shown on the compass rose as a wide,
white, corridor enclosing the course line. The outer edges of this white
corridor represent lines that show the current cross track error range.
The default for the cross track error range is 0.20 miles.
If the present position symbol touches the right cross track error line,
then you are 0.20 miles to the right of the desired course. You need to
29
Download from Www.Somanuals.com. All Manuals Search And Download.
steer left to return to the desired course. You can use the ZIN or ZOUT
keys to change the cross track error range.
Travel Time is the time that it will take to reach your destination at
your present closing speed. You can also customize the time data box to
show Arrival Time instead. Arrival Time is the local time it will be
when you arrive at the destination, based upon your present closing
speed and track.
In the preceding figure, the driver is headed northwest (a 307º track)
toward a waypoint 307º (bearing) away. The cross track error range
(white corridor) is 0.20 miles either side of the course. The driver is
headed toward trail waypoint 002, which is 5.65 miles away. Traveling
at a speed of 70 mph, the driver will arrive at the waypoint in 3 min-
utes, 24 seconds.
The Navigation Page has its own menu, which is used for some ad-
vanced functions and for setting various options. To access the Naviga-
tion Page Menu, from the Navigation Page, press MENU.
Map Page
The Map Page screens show your course and track from a "bird's-eye"
view. By default, this unit shows the map with north always at the top
of the screen. (This can be changed. See the topic Map Orientation, in
Sec. 5.) If you're navigating to a waypoint, the map also shows your
starting location, present position, course line and destination. You
don't have to navigate to a waypoint, however, to use the map.
Map Page is the default screen that appears when you turn on the unit.
To get to the Map Page from another page: Press PAGES|→ or ← to
MAP|EXIT. When the Map Page is displayed, a screen similar to the fig-
ures on the next page appears.
The arrow in the center of the screen is your present position. It points
in the direction you're traveling. The solid line extending from the back
of the arrow is your plot trail, or path you've taken.
The map zoom range is the distance across the screen. This number
shows in the lower left corner of the screen. In the first of the following
example figures, the range is 4,000 miles from the left edge of the map
to the right edge of the map.
The Zoom In and Zoom Out keys zoom the map to enlarge or reduce its
coverage area and the amount of mapping detail shown. There are 40
available map zoom ranges, from 0.02 miles to 4,000 miles.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Map Page opening screen (left). Map zoomed to 100 miles (center). Map
zoomed to 10 miles (right). Over Zoomed, listed at the top of the map
screen (right) means you have reached the detail limits in an area cov-
ered only by the basic background map. Zooming in any closer will
reveal no more map details because a high-detail custom map has not
been loaded on the MMC for this area.
If you are using only the factory-loaded background map, the maximum
zoom range for showing additional map detail is 15 miles. You can con-
tinue to zoom in closer, but the map will be enlarged without revealing
more map detail, except for a few major city streets. Load your own
high-detail custom map made with MapCreate or a pre-made Free-
domMap from LEI and you can zoom in to 0.02 miles with massive
amounts of accurate map detail.
Map Pages with high-detail MapCreate map of an urban area loaded on
the MMC. Arterial streets are visible at the 4-mile zoom range (left).
Numerous dots representing Points of Interest are visible at the 2-mile
range (center). Map zoomed into 0.4-mile range (right) .You can see an
interstate highway with an exit, major and minor streets as well as
Point of Interest icons.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Background map vs. MapCreate map content
The background map includes low-detail maps of the whole world (con-
taining cities, major lakes, major rivers, political boundaries) and me-
dium-detail maps of the United States.
The medium-detail U.S. maps contain: all incorporated cities; shaded
metropolitan areas; county boundaries; shaded public lands (such as
national forests and parks); some major city streets; Interstate, U.S.
and state highways; Interstate highway exits and exit services informa-
tion; large- and medium-sized lakes and streams; and more than 60,000
navigation aids and 10,000 wrecks and obstructions in U.S. coastal and
Great Lakes waters
MapCreate custom maps include massive amounts of information not
found in the background map. MapCreate maps contain the searchable
Points of Interest database, all the minor roads and streets, all the
landmark features (such as summits, schools, radio towers, etc.); more
rivers, streams, smaller lakes and ponds and their names.
What is more important is the large scale map detail that allows your
GPS unit to show a higher level of position accuracy. For example, the
background map would show you the general outline and approximate
shape of a coastline or water body, but the higher detail in MapCreate
shows the shoreline completely and accurately (finer detail). Many
smaller islands would not be included in the background map, but are,
of course, in MapCreate.
NOTE:
Available through LEI Extras − look inside back cover for accessory
ordering information − FreedomMaps are pre-made maps that con-
tain all of the same information available in a custom MapCreate
map, without any of the work of preparation.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Major Street
Interstate
Cursor line
Minor
Streets
POI
Pop-up
POI
Marker
School
POI
Restaurant
POI
Position, distance
and bearing data
Zoom Range
When the map is zoomed out far enough, most POIs appear as square
dots (left). As you zoom in closer, the symbols become readable icons.
In the 0.2-mile zoom example (right), the cursor has selected the Cupps
Café POI, which triggers a pop-up box with the POI name
Tip:
In some urban areas, businesses are so close to one another that
their POI icons crowd each other on the screen. You can reduce
screen clutter and make streets and other map features easier to
see by turning off the display of POIs you're not watching for. (To
see how, check the text on Map Detail Category Selection, page 81.
It shows how to use the Map Categories Drawn menu to turn indi-
vidual POI displays off and on.) Even though their display is turned
off, you can still search for POIs and their icons will pop-up when
your unit finds them for you.
The Map Page has its own menu, which is used for several functions
and for setting various options. To access the Map Page Menu, from the
Map Page, press MENU.
The Pages Menu also offers several map display options under the Map
Page category. To access them, press PAGES|← or → to MAP|↓ to Op-
tion|EXIT.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Digital Data map page option.
In pages that have two major windows you can toggle back and forth
between the two windows by pressing PAGES|PAGES. This allows you
to change the active map. Only when a map is active are you able to
make adjustments to it.
Pages Menu (left) with Two Map option selected.
Map Page (right) with two map windows.
Resize Window command
Resize Window is another feature for pages that has two major windows.
You can change the relative size of the windows, as well as the layout,
switching between horizontal and vertical.
1. From any two-window display, press MENU|↓ to RESIZE WINDOW|ENT.
2. Four flashing arrows appear along the centerline dividing the two
windows. Press an arrow key perpendicular to the centerline to adjust
34
Download from Www.Somanuals.com. All Manuals Search And Download.
the window widths. Press an arrow key parallel to the centerline to
switch between horizontal and vertical layout.
On the Map with Sonar page, you can only change size, not switch lay-
out. It is always two vertical windows. Press EXIT to clear the four
flashing arrows.
Fig. 1.
Fig. 3.
Fig. 4.
Fig. 2.
(From left to right) Fig. 1. Resize Window command on the GPS Page
menu. Fig. 2. Two Maps page display with four flashing arrows on the
dividing centerline. Fig. 3. The centerline has been moved down to en-
large the top map, which is now zoomed in to 40 miles. Fig. 4. Pressing
→ has switched the page layout from horizontal to vertical.
3. To change the window size again or revert back to the original dis-
play, just follow the steps above. Most dual-window displays use half
the screen for each window by default. You can also use the Reset Op-
tions command to revert to the factory default.
The following page contains a 12-step quick reference for the most basic
GPS operations. If you don't want to carry the manual with you as you
practice with the unit, you might consider photocopying this quick ref-
erence page and tucking it into your pocket.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic GPS Quick Reference
Start outdoors, with a clear view of the open sky. As you practice, try
navigating to a location at least a few blocks away. While you're learning,
navigation in too small an area will constantly trigger arrival alarms.
1. Connect the unit to electric power and the antenna module. Make sure
the MMC is in. (See complete installation details beginning on page 19.)
2. To turn on the unit, press and release PWR key.
3. Opening screen displays map of North America at 4,000 mile zoom
range. Rotate through the three main Page screens (Map Page, Satel-
lite Status Page and Navigation Page) by pressing PAGES|← or → to
select Page Name|EXIT. Switch Pages to display Satellite Status Page.
4. Wait while unit locates satellites and calculates current position. Process
is visible on Satellite Page. This takes about a minutes or less under clear
sky conditions (unobstructed by terrain or structures.) When position is
acquired, unit sounds a tone and displays a "position acquired" message.
The present position arrow and information shown in data boxes or as
overlay data will stop flashing.
5. With position acquired, press PAGES key to display Map Page, which
shows a bird's eye view of the earth. You can move around the map by:
Zoom in closer to see greater detail: press ZIN (zoom in key.)
Zoom out to see more area, less detail: press ZOUT (zoom out key.)
Scroll map north, south, east or west using arrow keys ↑ ↓ → ← .
To stop scrolling and return to current position on map, press EXIT key.
6. Set a waypoint (Wpt 001) at your current position so you can navigate
back here: press WPT|WPT. Waypoint symbol and "001" appears.
7. Zoom/scroll map to find a nearby object or location to go to. Use ar-
row keys to center cursor cross-hair over the map object or location.
8. Navigate to the selected destination: press MENU|ENT|EXIT. Follow red
course line on Map Page or compass bearing arrow on Navigation Page.
9. At destination, Arrival Alarm goes off; to clear it, press EXIT. Cancel
navigation: press MENU|MENU|↓ to CANCEL NAVIGATION|ENT|← to YES|ENT.
10. Return to Wpt 1 by Navigate To Waypoint or Backtrack Trail. To
Waypoint: press WPT|ENT|ENT. Use ↑ or ↓ to select Wpt 001, press
ENT|ENT; follow navigation displays. Trail: press MENU|MENU|↓ to MY
TRAILS|ENT. Press ↓ to Trail 1|ENT|↓ to DELETE TRAIL|→ to NAVIGATE|ENT.
Press → to REVERSE ROUTE|ENT|← to NAVIGATE ROUTE|ENT. (If arrival
alarm sounds, press EXIT.) Follow navigation displays.
11. Back home, Arrival Alarm goes off; press EXIT. Cancel navigation:
press MENU|MENU|↓ to CANCEL NAVIGATION|ENT|← to YES|ENT.
12. To turn off the unit, press and hold PWR key for three seconds.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Find Your Current Position
Finding your current position is as simple as turning the unit on. Un-
der clear sky conditions, the unit automatically searches for satellites
and calculates its position in approximately one minute or less.
NOTE:
"Clear sky" means open sky, unobstructed by terrain, dense foliage
or structures. Clouds do not restrict GPS signal reception.
If for some reason satellite acquisition takes longer, you may be inside
a structure or vehicle or in terrain that is blocking signal reception. To
correct this, be sure you are positioned so that the unit's antenna mod-
ule has as clear a view of the sky as possible, then turn the unit off and
back on again.
Moving Around the Map: Zoom & Cursor Arrow Keys
The map is presented from a bird's eye view perspective. The current
zoom range shows in the lower left corner of the screen.
1. Press the ZIN key (zoom in) to move in closer and see greater detail in
a smaller geographic area.
2. Press the ZOUT key (zoom out) to move farther away and see less map
detail, but a larger geographic area.
When you are traveling, the map will automatically move as you move.
This keeps your current location roughly centered on the screen.
You can manually pan or scroll the map northward, southward, east-
ward or westward by using the arrow keys, which launch the cross-hair
map cursor. This allows you to look at map places other than your cur-
rent position. To clear the cursor, press EXIT, which jumps the map
back to the current position or the last known position.
Tip:
Use the cursor to determine the distance from your current position
(or last known position, when working indoors) to any map object or
location. Use the arrow keys to position the cursor over the object
or place. The distance, measured in a straight line, appears in the
popup data box. Press EXIT to clear the cursor.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Distance
measured
by cursor
Pop-up
name box
Selected wreck
Cursor line
Cursor
line
The selected wreck (the Empress) to the southeast is 40 miles away.
Selecting Any Map Item with the Cursor
1. Use the zoom keys and the arrow keys to move around the map and
find the item you wish to select.
2. Use the arrow keys and center the cursor cross-hair on the desired ob-
ject. On most items, a pop-up box will give the name of the selected item.
Tip:
This unit has a Cursor Undo feature that lets you instantly return
to the previous location you were looking at without scrolling. Use
the cursor (arrow keys) to scroll the map to some far away location
or waypoint. Press EXIT to clear the cursor and jump back to your
current position on the map. When you want to take another peek
at that distant place, just press EXIT again. You can use this trick to
toggle between your current position and your destination without
a lot of scrolling.
Searching
Now that you have seen how the unit can find where you are, let's
search for something somewhere else. Searching is one of the most
powerful features in the Eagle GPS product line.
In this example, we will look for the nearest fast-food restaurant. For
more information on different types of searches, refer to Sec. 6, Searching.
NOTE:
This example requires the Point of Interest (POI) database included
with a high detail MapCreate 6 custom map.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
After the unit has acquired a position:
1. Press WPT|↓ to POI-RESTAURANTS.
2. You could search the entire restaurant category, but in this example
we will narrow our search. Press → to FAST FOOD CHAINS|ENT|ENT.
3. The unit says it is calculating, then a list of restaurants appears,
with the closest at the top of the list, and the farthest at the bottom of
the list. The nearest is highlighted.
Find Waypoint Menu (left). Category Selection menu (center). List of
the nearest restaurants (right).
4. If you wish, you could scroll ↑ or ↓ here to select another restaurant,
but for now we will just accept the nearest one. Press ENT.
POI information screen on fast food restaurant nearest this position.
Screen shows name, street address, phone number, latitude/longitude,
distance to restaurant and its compass bearing. Go To command high-
lighted (left). Find On Map command highlighted (right).
39
Download from Www.Somanuals.com. All Manuals Search And Download.
5. The POI information screen appears. (This is how you can use this
unit as a business phone directory!) If you wanted to navigate there,
you could press Enter, since the Go To waypoint command is high-
lighted. But we just want to see it on the map, so press → to FIND ON
MAP|ENT.
6. The unit's map appears, with the cross-hair cursor highlighting the
restaurant' s POI symbol. A pop-up data box shows the POI's name. A
data box at the bottom of the screen displays the location's latitude and
longitude, distance and bearing.
Finding Waypoint screen showing
the result of a restaurant search.
7. To clear the search and return to the last page displayed, press EXIT
repeatedly. Before you completely exit out of the Search menus, you can
go looking for another place.
NOTE:
Search works from mapping and POI data loaded in the unit. If
you do not have a high-detailed custom map (containing POI data)
for the area you are searching loaded on the MMC, you may not
find anything.
Set a Waypoint
A waypoint is an electronic address based on the latitude and longi-
tude of a position on the earth. A waypoint represents a location, spot,
or destination that can be stored in memory, then be recalled and used
later on for navigation purposes.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
You can create a waypoint at the cursor position on the map, or at your
current position while you are navigating. You can create a waypoint at
any location by manually entering the position's latitude and longitude.
You can copy waypoints from your unit to your personal computer with
MapCreate software. When you want to repeat a trip, these archived
waypoints can be reloaded into your GPS unit.
To create and save a Waypoint:
These first two techniques use the Quick Save method, the fastest and
easiest way to create a waypoint.
Create Waypoint at Current Position
While you are traveling, press WPT|WPT. The waypoint is saved and
automatically given a name with a sequential number, such as "way-
point 003." The waypoint symbol and number appear on the map.
NOTE:
The Quick Save method uses the default waypoint symbol until you
edit an existing waypoint and change its symbol. (Edit Waypoint
Symbol is described in Sec. 4.) After you have changed a waypoint
symbol the unit will remember the one you chose and use it the next
time you "quick save" a waypoint. To revert back to the default
symbol, edit a waypoint and choose the original symbol, or use the
Reset Options command (described in Sec. 5).
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 1.
Step 2.
Step 4.
Step 3.
Sequence for setting a waypoint. Step 1: while traveling, press WPT to
call up Find Waypoint screen (seen in Step 2) and set a point. Step 3: a
message says the waypoint has been saved. Step 4: vehicle continues
on its way; number waypoint symbol is visible on map.
Create Waypoint on Map
1. Use the arrow keys to move the cursor to the place where you want
to make a waypoint.
2. Press WPT|WPT. The waypoint is saved and automatically given a
name with a sequential number, such as "waypoint 001." The waypoint
symbol and number appear on the map.
Create Waypoint by Entering a Position
1. Press WPT|↑ to MY WAYPOINTS|→ to NEW|ENT.
2. Press ↓ to ENTERED POSITION|ENT|→ to CREATE|ENT.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Press → to LATITUDE|ENT. Enter the latitude by pressing ↑ or ↓ to
change the first character, then press → to the next character and re-
peat until the latitude is correct. Press ENT.
4. Press ↓ to LONGITUDE|ENT. Enter the longitude by pressing ↑ or ↓ to
change the first character, then press → to the next character and repeat
until the longitude is correct. Press ENT, then EXIT|EXIT to return to the
previous page display. The waypoint is saved and automatically given a
name with a sequential number, such as "waypoint 001." The waypoint
symbol and number appear on the map and in the waypoint list.
Navigate To a Waypoint
You can select any waypoint visible on the Map Page with the cursor,
then use the Navigate to Cursor command (we will describe how later
in this section.) You can avoid scrolling the map to pick your waypoint
if you use the Find Waypoint commands.
1. Press WPT|↑ to MY WAYPOINTS|ENT. To look up the nearest waypoint,
press ↓ to NEAREST | ENT. To look by name — and scroll through the en-
tire waypoint list — press ↓|ENT. For this example, let's look by name.
2. If your waypoint list is a long one, you can spell out the waypoint name
in the FIND BY NAME box. Press ↑ or ↓ to change the first character, then
press → to move the cursor to the next character and repeat until the
name is correct, then press ENT to jump to the list below.
3. If the list is short, you can jump directly to the FIND IN LIST box by
pressing ENT. Use ↑ or ↓ to select the waypoint name, press ENT and the
waypoint information screen appears with the GO TO command selected.
4. To begin navigating to the waypoint, press ENT.
Course line
(red)
Trail line
(magenta)
Off course
range, set at
0.20 mile
Destination
name
Navigating to waypoint 002 and leaving a trail
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Set Man Overboard (MOB) Waypoint
One of boating's most terrifying events is having a friend or family
member fall overboard. This unit has a man overboard feature that
shows navigation data to the location where the feature was activated.
To activate it, press the ZOUT and ZIN keys at the same time. Your posi-
tion at the time these keys are pressed is used as the man overboard
position.
Caution:
Saving a new Man Overboard waypoint will overwrite and erase
the previous Man Overboard waypoint.
Navigate Back to MOB Waypoint
Find your way back to the accident position with the Navigation Page
or Map Page. When MOB is activated, the Navigation Page automati-
cally shows the compass rose with its bearing arrow pointing toward
the man overboard position, and the destination name says Going To
Man Overboard. The Map Page displays a Man Overboard waypoint,
represented by a human figure, and the steering arrow points where to
steer to reach that position.
Navigating to Man Overboard: Man Overboard activated message
(left). The Navigation Page is shown (center). Going to Man Overboard
position on Map Page (right).
The man overboard position is also stored in the waypoint list for future
reference. It can be edited the same as any other waypoint. This pre-
vents the inadvertent loss of the current Man Overboard position.
To cancel navigation to MOB, press MENU|MENU|↓ to CANCEL
NAVIGATION|ENT|← to YES|ENT. The unit stops showing navigation infor-
mation.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Navigate to Cursor Position on Map
The GO TO CURSOR command navigates to the current cursor position on
the map. It is a quick way to navigate to anything you can see on the
map display.
1. Use the cursor with the zoom in and zoom out keys to move around
the map until you find a location you want to go to.
2. Center the cursor over the location to select it. See the example in
the following figure. Many map items such as waypoints, Points of In-
terest, towns, etc. can be selected, and appear highlighted with a pop-
up box. Other features, such as a river or a street intersection will not
appear highlighted, but the cursor will take you to those locations just
the same.
The cursor crosshairs are centered on Oologah, Oklahoma.
3. Press MENU|ENT and the unit will begin navigating to the cursor lo-
cation.
The Map Page will display a red line from your current position to the cur-
sor position. The Navigation Page displays a compass rose showing naviga-
tion information to your destination. See the following examples.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Active
symbol
Course
Line
The 60-mile zoom figure (left) shows the red course line connecting the
current position to the destination. The Navigation Page (right) will also
show navigation information.
To stop navigating to the cursor, use the Cancel Navigation command.
Press MENU|MENU|↓ to CANCEL NAVIGATION|ENT|← to YES|ENT. The unit
stops showing navigation information.
Navigate to a Point of Interest
For POIs that are in view on the map, you can easily use the Navigate
to Cursor command above; just use the cursor to select the POI.
The other method involves searching for POIs with the Find Waypoint
command, launched with the WPT key. (See the searching example ear-
lier in this section, or turn to Sec. 6, Searching, for detailed instructions
on POI searches.)
After you have looked up an item with the Find Waypoint command,
use ← or → to make sure the GO TO command is highlighted at the bot-
tom of the screen, then press ENT. The unit begins showing navigation
information to the item.
To cancel navigation, press MENU|MENU|↓ to CANCEL NAVIGATION|ENT|←
to YES|ENT. The unit stops showing navigation information.
Creating and Saving a Trail
A trail, or plot trail, is a string of position points plotted by the unit as you
travel. It's a travel history, a record of the path you have taken. Trails are
useful for repeating a journey along the same track. They are particularly
handy when you are trying to retrace your trip and go back the way you
came. On the screen, trails are represented by a solid line extending from
the back of the current position arrow. The default color is light magenta.
The unit is set at the factory to automatically create and record a trail
while the unit is turned on. The unit will continue recording the trail
46
Download from Www.Somanuals.com. All Manuals Search And Download.
until the length reaches the maximum trail point setting (default is
2,000, but the unit can record trails 9,999 points long). When the point
limit is reached, the unit begins recording the trail over itself.
With the default auto setting, this unit creates a trail by placing a dot
(trail point) on the screen every time you change directions. The methods
used for creating a trail and the trail update rate can both be adjusted or
even turned off. See Sec. 5 for Trail Options.
To preserve a trail from point A to point B, you must "turn off" the trail
by making it inactive before heading to point C or even back to point A.
When the current trail is set inactive, the unit automatically creates
and begins recording a new trail.
To Save a Trail
1. Press MENU|MENU|↓ to MY TRAILS|ENT.
Visible
Active
symbol
symbol
Sequence for saving a trail and beginning a new one. My Trails com-
mand (left). The Trails Menu (center). The arrow to the right of Trail 3
indicates the trail is active and the check to the left indicates the trail
is visible on the map display. The third figure (right) shows the Edit
Trail menu, with the Name command selected.
2. Press ↓ to the Active Trail Name|ENT.
3. Press ↓ → to ACTIVE|ENT. This unchecks the Active option.
4. To return to the previous page, press EXIT repeatedly. As you leave
the Edit Trail menu, a new trail starts with a new sequential number.
You can save and recall up to 10 different plot trails, which can be cop-
ied to your MMC for archiving or for transfer to your MapCreate soft-
ware.
You can save and recall up to 10 different plot trails, which can also be
copied to your MMC for archiving or for transfer to your MapCreate
software.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Tip:
Another quick way to stop recording one trail and begin a new one
is to use the New Trail command. Press MENU|MENU|↓ to MY
TRAILS|ENT|ENT.
Caution:
You also have the option of completely turning off trail record-
ing, under the trail Options command. However, if the Update
Active Trail option is left turned off, it will cancel the automatic
trail creation feature.
Displaying a Saved Trail
The active trail is automatically displayed on the map with the factory
default settings. You can selectively turn trail display off and on for any
saved or active trail. In the Saved Trails List, visible trails have a check
mark in front of the trail name.
To turn off trail display:
1. Press MENU|MENU|↓ to MY TRAILS|ENT.
2. Press ↓ to enter the Saved Trail list, then use ↑ or ↓ to select the de-
sired Trail Name|ENT.
3. Press ↓ → to VISIBLE|ENT. To return to the previous page, press EXIT
repeatdly. Repeat the steps above to turn on the trail display.
To turn on trail display:
1. Press MENU|MENU|↓ to MY TRAILS|ENT.
2. Press ↓ to enter the Saved Trail list, then use ↑ or ↓ to select the de-
sired Trail Name|ENT.
3. Press ↓ → to VISIBLE|ENT. To return to the previous page, press EXIT
repeatedly.
Navigating Trails
There are three methods for following a trail: visual trailing, navigating
a trail (forward) and backtracking a trail (backward). Try each method
to see which you prefer.
Visual trailing is the simplest method. It uses only the Map Page and
requires no menu commands at all. The technique works the same if
you are running a trail forward (from start to end) or backward (from
end to start.) However, visual trailing provides no navigation informa-
tion during the trip, such as the time to your destination.
The other two methods provide a full range of navigation data and work
with both the Map Page and Navigation Page. The only difference be-
48
Download from Www.Somanuals.com. All Manuals Search And Download.
tween them is "navigating a trail" follows a trail forward (from start to
end) while "backtracking" follows a trail in reverse (from end to start.)
When hiking at walking speed with a hand-held GPS, we often just use
visual back trailing because it is a bit better at following each little
turn on a foot path. At faster speeds, such as the highway or on the wa-
ter, the Navigate Trail and Backtrack Trail commands are handy.
Visual Trailing
1. On the Map Page, zoom (ZIN or ZOUT) so your trail is visible.
2. Begin moving and watch the Map Page. Walk or steer so your cur-
rent position arrow traces along the trail you have just made.
Tip:
Generally, when using this method, the smaller the zoom range, the
more accurately you will be able to steer along the trail.
Navigate a Trail
The following figures illustrate the menu sequence for navigating a trail.
1. Press MENU|MENU|↓ to MY TRAILS|ENT.
2. Press ↓ to enter the Saved Trail list, then use ↑ or ↓ to select the de-
sired Trail Name|ENT.
3. Press ↓ → to NAVIGATE|ENT. Press ↓|NAVIGATE| ENT.
The unit begins showing navigation information along the trail.
NOTE:
If you are already located at or near the beginning of your trail, the
arrival alarm will go off as soon as you hit Enter. Just press EXIT to
clear the alarm and proceed.
5. Now, begin moving and follow your unit.
6. When you reach your destination, be sure to cancel your navigation:
press MENU|MENU|↓ to CANCEL NAVIGATION|ENT. A confirmation message
will appear. Press ←|ENT.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 1.
Figure 2.
Figure 4.
Figure 3.
Navigate a trail menu sequence: Fig. 1, My Trails command. Fig. 2,
Trails Menu. Fig. 3, Edit Trail Menu. Fig. 4, Edit Route Menu with
Navigate Route command highlighted for Trail 2. A trail is always con-
verted to a route when you navigate the trail.
On the Map Page, the trail you are navigating is represented by a ma-
genta line when the visible trail option is on. The course you are follow-
ing is represented by a red line. The magenta trail line overlays the red
course line. To see the red course line, you much turn off the visible trail
option. The Navigation Page will show only the red course line, unless
you are recording a new trail. The bearing arrow on the compass rose
points to the next waypoint on the trail.
As you travel, the arrival alarm will go off when you near a trail way-
point, and the bearing arrow on the compass rose will swing around
and point to the next trail waypoint. Press EXIT to clear the alarm.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
North ꢀ
Present
position
arrow
Magenta
trail line
Trail point
Navigate trail: Driver (left) is heading southeast straight toward trail
point 3. Driver (right) has reached point 3 and has turned southwest to
follow the trail.
Track or compass heading indicator
Bearing arrow
Trail
waypoint
symbol
Red course
line made
from trail
Magenta new
trail
Cross track
error range
(off course
indicator)
Arrival
alarm
Navigate trail, navigation page (compass rose) views: Driver is heading
north straight toward trail point 3 (left). Bearing arrow shows the
bearing to the trail point is 355 degrees. Driver has reached trail point
3 (right), causing the Arrival alarm to go off. The unit now shows
navigation information to point 4, which is 1.42 miles away.
Navigate a Back Trail
1. Press MENU|MENU|↓ to MY TRAILS|ENT.
2. Press ↓ to enter the Saved Trail list, then use ↑ or ↓ to select the de-
sired Trail Name|ENT.
3. Press ↓ → to NAVIGATE|ENT.
4. Press ↓ → to REVERSE ROUTE|ENT|← to NAVIGATE|ENT. The unit shows
navigation information along the trail, in reverse.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE:
If you are already located at or near the end of your trail, the arri-
val alarm will go off as soon as you hit Enter. Just press EXIT to
clear the alarm and proceed.
5. Now, begin moving and allow the unit to guide you.
6. When you reach your destination, be sure to cancel your navigation.
Press MENU|MENU|↓ to CANCEL NAVIGATION|ENT. A confirmation message
will appear. Press ←|ENT.
Transfer Custom Maps and GPS Data Files
Custom Maps:
Custom maps work only from the MMC card or SD card. When a card
containing a Custom Map File is loaded into the unit, the unit auto-
matically loads the map into memory when the unit is turned on.
Instructions for copying Custom Map Files to an MMC are contained in
the instruction manual for your MMC card reader and MapCreate 6
software. For instructions on inserting an MMC into the unit, see Sec.
2, Installation/Accessories.
GPS Data files:
GPS Data Files contain waypoints, routes, trails and event marker
icons. Instructions for copying GPS Data Files between your computer
and an MMC are contained in the instruction manual for your MMC
card reader and MapCreate 6 software.
You must enter which way you want to transfer data, from an MMC
card to the unit (load) or from the unit to an MMC card (save).
GPS data automatically recorded in the unit's internal memory must be
saved to the MMC (as a GPS Data File) in order to store it on your per-
sonal computer. GPS Data Files stored on an MMC must be copied from
the card to the unit's internal memory before the unit can read them.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Insert the MMC into your unit. Press MENU|MENU|↓ to SYSTEM
SETUP|ENT|↓ to TRANSFER MY DATA|ENT.
2. The Transfer My Data menu includes a message which tells you if an
MMC is present or not. If no MMC is present, you must first insert a
card into the unit in order to activate the Load or Save commands.
To transfer data from the unit to the MMC: press ENT (for SAVE.)
To transfer data from the MMC to the unit: press → to LOAD|ENT.
3. Saving to MMC: To accept the default name "Data" for the GPS
Data File, press ↓ to SAVE DATA|ENT. If you wish to rename the file (as
shown in the following figures), press ENT to activate the selection box.
Press ↑ or ↓ to change the first character, then press → to the next
character and repeat until the name is correct. Then, press ENT|↓ to
SAVE DATA|ENT.
The unit will display first a progress then a completion message when
the data transfer is finished. To return to the Page view, repeatedly
press EXIT.
These figures (from left) show the menu sequence for naming and sav-
ing a GPS Data File from the unit's memory to an MMC.
4. Loading to unit memory: There may be more than one GPS Data
File (*.USR) on the card. To select a file, press ENT to activate the selec-
tion box, use ↓ or ↑ to highlight the file, then press ENT to accept the
selection. Next, press ↓ to LOAD DATA|ENT. The unit will display a com-
pletion message when the data transfer is finished. To return to the
Page view, press EXIT repeatedly.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 2.
Figure 1.
Figure 3.
Figure 4.
These figures show the menu sequence for loading a GPS Data File
from an MMC into the unit's memory.
Cancel Navigation
You can turn off any of the navigation commands after you reach your
destination or at any other time by using the Cancel Navigation com-
mand. Press MENU|MENU|↓ to CANCEL NAVIGATION|ENT|← to YES|ENT.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4:
Advanced GPS Operations
Find Distance From Current Position To Another Location
1. While on the Map Page press MENU|↓ to FIND DISTANCE|ENT.
2. Center your cursor over the position you want to find the distance to.
A rubber band line appears, connecting your current position to the
cursor's location. The distance along that line will appear in a pop-up
box. The box also shows the bearing to the point you're measuring to.
3. Press EXIT|EXIT to return to regular operation.
The distance (left) from the boat's current position to the cove is 5.78
miles. The distance (right) from Houston to New Orleans is 316.9 miles.
Find Distance From Point to Point
You can also measure distance between two other points on the map.
1. While on the Map Page press: MENU|↓ to FIND DISTANCE|ENT.
2. Center your cursor over the first position. A rubber band line ap-
pears, connecting your current position to the cursor's location. Press
ENT to set the first point, and the rubber band line disappears.
3. Move the cursor to the second position. The rubber band line reap-
pears, connecting the first point you set to the cursor. The distance
along that line will appear in the pop-up box.
4. Press EXIT|EXIT to return to regular operation
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Icons
Icons are graphic symbols used to mark some location, personal point of
interest or event. They can be placed on the map screen, saved and re-
called later for navigation purposes. These are sometimes referred to as
event marker icons. This unit has 42 different symbols you can pick
from when creating an icon.
Icons are similar to waypoints, but they do not store as much informa-
tion (like names) as waypoints do. You can't use a menu to navigate to
icons as you can with waypoints. But, you can use the map cursor and
navigate to any icon on the map.
You can create an icon at the cursor position on the map, or at your
current position while you are navigating.
Create Icon on Map
1. Use the arrow keys to move the cursor to the place where you want
to make an icon.
2. Press ENT and the screen displays the Select Icon Symbol menu.
3. Select the desired icon symbol and press ENT. The icon appears on
the map. Press EXIT to clear the cursor.
Cursor selects icon location (left). Select Icon Symbol menu (center).
Boat Ramp icon on map (right). (Cursor has been moved for clarity.)
Create Icon at Current Position
1. While you are traveling, press ENT and the screen shows a "Select
Icon Symbol" menu.
2. Press ← or ↑ or → or ↓ to select your icon symbol, then press ENT.
The icon appears on the map.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Delete an Icon
You can delete all the icons at one time, you can delete all icons repre-
sented by a particular symbol, or you can use the cursor to delete a se-
lected icon from the map.
Delete icons menu.
1. Press MENU|↓ to DELETE MY ICONS|ENT.
2. Press ↓ to DELETE ALL ICONS, DELETE BY SYMBOL or DELETE FROM MAP and
press ENT.
3. The Delete All Icons confirmation message will appear. Press ← to
YES|ENT. All icons will be deleted from the map.
The Delete by Symbol command will launch the Select Symbol menu.
Select the desired icon symbol to delete and press ENT. A message ap-
pears saying all icons with the selected symbol have been deleted.
The Delete From Map command will prompt you to move the cursor
over an icon to select it. After selecting the icon, press ENT and it disap-
pears from the map.
Navigate to an Icon
To execute the Navigate to Cursor command, use the cursor to select
the desired icon on the map.
1. Center cursor crosshairs on an icon.
2. To navigate to the icon press MENU|ENT|EXIT. Follow course line on
the Map Page or the compass bearing arrow on the Navigation Page.
Routes
A route is a series of waypoints linked together in an ordered sequence
used to mark a course of travel. You can visualize a route as a string of
beads. The beads represent waypoints and the string represents the
57
Download from Www.Somanuals.com. All Manuals Search And Download.
course of travel connecting waypoint to waypoint. The course from one
waypoint to the next is a leg. Routes are composed of one or more legs.
The legs of all GPS routes are based on straight lines between way-
points. A route allows you to navigate through several waypoints with-
out having to reprogram the unit after arriving at each waypoint. Once
programmed into the GPS unit, a route provides the option of navigat-
ing forward through the route waypoints or in reverse order. You can
even begin navigating in the middle of a route.
Create and Save a Route
You have the option of creating and editing a route in the unit, or you
can make a route on your computer with our MapCreate 6 software.
PC-created Routes
MapCreate is the easiest method for preparing a route, because your
PC's larger screen, keyboard and mouse are easier to manipulate than
the unit. To load a MapCreate route into the unit, follow instructions in
MapCreate's manual for creating a route and saving it as part of a GPS
Data File (file format *.usr). Copy the GPS Data File to an MMC and
insert the MMC in the unit. (See Sec. 2 for instructions on installing
MMCs. To load the GPS Data File into the unit's memory, see the entry
on Transfer Custom Maps & GPS Data Files in Sec. 3, Basic GPS Opera-
tions.)
Routes Created in the Unit
You can create a route by selecting existing waypoints from the way-
point list or you can set a series of route waypoints on the map with
cursor arrows and the Enter key. In this example, we'll create a route
from the map.
1. From the NAVIGATION PAGE, press MENU|ENT or from the MAP PAGE,
press MENU|MENU|↓ to ROUTE PLANNING|ENT.
Route Planning (left) command on Main Menu.
Route List menu at right.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Press ↑ to NEW ROUTE, then press ENT. To add to an existing route,
press ↓ or ↑ to route name|ENT.
Edit Route menu (left). Edit Route Waypoints menu (right)
with Add From Map command selected.
3. Press ↓ to END OF ROUTE|ENT|↓ to ADD FROM MAP|ENT. The Map Page
appears with the cursor showing.
4. Use the Zoom and arrow keys to move the map and cursor until the
cursor is centered on the spot where you want your route to begin.
5. To set the first route waypoint press ENT. In the example below, we
moved to the entrance of the cove where our boat was docked.
1.
2.
3.
Route creation sequence (from left): Fig. 1. Set route waypoint (1) at
the cove entrance. Fig. 2. Move cursor northeast to set point (2) at
channel entrance. Fig. 3. With point (2) set, move cursor southeast to
mark channel exit with waypoint (3). In figures 2 and 3, notice the
rubber band line extending from the previously set waypoint to the
cursor. This line will become the course for the route
59
Download from Www.Somanuals.com. All Manuals Search And Download.
4.
5.
6.
Route creation sequence, continued: Fig. 4. Point (3) set at channel mouth.
Fig. 5. Waypoint (4) set further south along the beach, at a recognizable
landmark. The route will end with waypoint 5 at an oil platform. Fig. 6.
Press EXIT to save the route and you return to this screen.
6. Move the cursor to the next point in the route, a spot where you need
to turn or change direction, and press ENT to set the next waypoint.
7. Repeat step six until the route reaches your destination.
8. To save your route, press EXIT. The unit reverts to the Edit Route
screen, with the route automatically named "Route 1" and stored in the
unit's internal memory.
You can edit the route and run other commands, but if you are finished
with the route for now, return to the last page displayed by
pressing EXIT repeatedly.
NOTE:
When adding waypoints to an existing route, the inserted way-
points will appear in the route in front of the waypoint you have
selected in the Edit Route menu. To insert waypoints at the end of
the route, make sure to select (ROUTE END) before adding them.
Delete a Route
1. From the NAVIGATION PAGE, press MENU|ENT or from the MAP PAGE
press MENU|MENU|↓ to ROUTE PLANNING|ENT.
2. Press ↓ to route name|ENT.
3.Highlight DELETE|ENT|← to YES|ENT.
Tip:
You can also delete all routes at once:
1. From the NAVIGATION PAGE, press MENU|ENT or from the MAP PAGE
press MENU|MENU|↓ to ROUTE PLANNING|ENT.
2. Press → to DELETE ALL|ENT|← to YES|ENT.
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Edit a Route Name
1. From the NAVIGATION PAGE, press MENU|ENT or from the MAP PAGE
press MENU|MENU|↓ to ROUTE PLANNING|ENT.
2. Press ↓ to route name|ENT|→ to EDIT ROUTE NAME|ENT.
3. Press ↑ or ↓ to change the first character, then press → to move the
cursor to the next character and repeat until the name is correct, then
press
ENT.
Return to the previous page by pressing
EXIT|EXIT|EXIT|EXIT.
Edit Route Waypoints
You can edit the route by adding and removing waypoints.
1. From the NAVIGATION PAGE, press MENU|ENT or from the MAP PAGE
press MENU|MENU|↓ to ROUTE PLANNING|ENT.
2. Press ↓ to route name|ENT|↓ to Route Waypoints List. Use ↓ and ↑
to select a waypoint, then press ENT.
Edit Route Waypoints menu.
3. Use ↓ and ↑ to select a command from the Edit Route Waypoints
menu and press ENT. Add From Map lets you insert a waypoint in the
route by clicking on a map location with the cursor. Add Waypoint calls
up the Waypoint List so you can insert a waypoint from the list. Re-
move Waypoint will delete the waypoint from the route. View Waypoint
will show you where the selected waypoint is on the map.
NOTE:
When adding waypoints to a route, the inserted waypoints will ap-
pear in the route in front of the waypoint you have selected. To in-
sert waypoints at the end of the route, select (ROUTE END) before
adding them.
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Navigate a Route
1. From the NAVIGATION PAGE, press MENU|ENT or from the MAP PAGE,
press MENU|MENU|↓ to ROUTE PLANNING|ENT.
Route Planning command (left) on Main Menu. Routes menu (center)
with Edit Route menu at right. Navigate Route command is selected.
2. Press ↓ to select saved route name|ENT. Highlight NAVIGATE and press
ENT.
3. Upon arrival at your destination, cancel navigation. Press
MENU|MENU|↓ to CANCEL NAVIGATION|ENT|← to YES|ENT.
The following figures show what the Navigation Page and Map Page
look like while navigating a route.
Navigate a Route in Reverse
Here's how you run a route backward, from the end waypoint to the
beginning waypoint:
1. From the NAVIGATION PAGE, press MENU|ENT or from the MAP PAGE,
press MENU|MENU|↓ to ROUTE PLANNING|ENT.
2. Press ↓ to saved route name|ENT. Highlight REVERSE | ENT|← to
NAVIGATE |ENT.
3. Upon arrival at your destination, cancel navigation:
Press MENU|MENU|↓ to CANCEL NAVIGATION|ENT|← to YES|ENT.
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Edit Route screen showing Route 1 with waypoints set to normal
navigation (left). Reverse command has been executed (center) revers-
ing the order of waypoints on the route. Pressing Navigate (right) will
allow you to navigate the route from the end to the beginning.
Trails
Delete a Trail
This is the command used to erase or delete
a
trail.
Press MENU|MENU|↓ to MY TRAILS|ENT|↓ to trail name|ENT|→ to
DELETE TRAIL|ENT|← to YES|ENT.
To Delete all trails at once
1. Press MENU|MENU|↓ to MY TRAILS|ENT.
2. Press → to DELETE ALL|ENT|← to YES|ENT.
Edit a Trail Name
To edit a trail name press MENU|MENU|↓ to MY TRAILS|ENT|↓ to trail
name|ENT|ENT. Press ↑ or ↓ to change the first character, then press
→ to the next character and repeat until the name is correct. Press ENT
then EXIT repeatedly to return to the previous page.
Tip:
You can quickly call up the Edit Trail menu by selecting a trail on
the map with the cursor. move the cursor over a trail and a pop-up
box appears. Press WPT and the Edit Trail menu opens.
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Trail selected with map cursor (left). The box at the bottom of the
screen shows distance and bearing from current position to the se-
lected point on the trail. The Edit Trail menu (right).
Edit a Trail Color
To edit a trail color press MENU|MENU|↓ to MY TRAILS|ENT|↓ to trail
name|ENT|↓ to COLOR|ENT. Press ↑ or ↓ to select a color style, then
press ENT. Press EXIT repeatedly to return to the previous page.
Edit a Trail Pattern
To edit a trail pattern press MENU|MENU|↓ to MY TRAILS|ENT|↓ to trail
name|ENT|↓ to PATTERN|ENT. Press ↑ or ↓ to change the first character,
then press → to the next character and repeat until the pattern is cor-
rect. Press ENT. To get back to the main page press EXIT repeatedly.
Edit Trail Menu (left) with Pattern option selected. Edited trail with
dotted line pattern is shown at right.
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Utilities
Utilities are useful tools for traveling or for outdoor activities.
Alarm Clock
To get to the alarm clock menu press MENU|MENU|↓ to TIMERS|ENT|↓
to ALARM CLOCK|ENT.
Sun/Moon Rise & Set Calculator
To get to the Sun/Moon menu press MENU|MENU|↓ to SUN/MOON
CALCULATIONS|ENT.
Trip Calculator
To get to the Calculator menu press MENU|MENU|↓ to TRIP
CALCULATOR|ENT.
Trip Down Timer
To get to the Down Timer menu press MENU|MENU|↓ to TIMERS|ENT|↓
to DOWN TIMER|ENT.
Trip Up Timer
To get to the Up Timer menu press MENU|MENU|↓ to TIMERS|ENT|ENT.
Waypoints
Delete a Waypoint
To delete a waypoint from the waypoint list press WPT|↑ to MY
WAYPOINTS|ENT|↓ to Name|ENT. Press ↑ or ↓ to select the desired char-
acter then press → to choose the next character. After the desired
waypoint is highlighted in the list, press ENT|ENT. Use ↓ to select
DELETE WAYPOINT then press |ENT|← to YES|ENT. To return to the main
page display, press EXIT repeatedly.
Delete a Waypoint from the map
1. Use the arrow keys to select the waypoint with the cursor.
2. Press WPT to view the WAYPOINT INFORMANTION screen, then ↓ to DELETE
WAYPOINT|ENT|← to YES|ENT. To return to the main page display, press
EXIT repeatedly.
To delete all waypoints at one time press MENU|MENU|↓ to SYSTEM
SETUP|ENT|↓ to DELETE ALL MY WAYPOINTS|ENT|← to YES|ENT. To return
to the previous page, press EXIT|EXIT.
Edit a Waypoint
To edit waypoint name:
1. Press WPT|↑ to MY WAYPOINTS|ENT|↓ to name|ENT. Choose desired
waypoint from the list by using ↑ or ↓ to select first character, then
press → to choose the next character. After the desired waypoint is
65
Download from Www.Somanuals.com. All Manuals Search And Download.
highlighted in the list, press ENT|ENT to access waypoint information
screen.
2. Use ↓ to select EDIT WAYPOINT, then press ENT|ENT. Press ↑ or ↓ to
change the first character, then press → to the next character and re-
peat until the name is correct. Press ENT. To get back to the main page
display, press EXIT repeatedly.
Waypoint Symbol
To edit waypoint symbol:
1. Press WPT|↑ to MY WAYPOINTS|ENT|↓ to name|ENT. Select waypoint
from the list then press ENT|ENT. Use ↓ to select EDIT WAYPOINT.
Press|ENT|↓ to CHOOSE SYMBOL|ENT.
2. Select the desired symbol and press ENT. To get back to the main
page display, press EXIT repeatedly.
Waypoint Position
To edit waypoint position:
1. Press WPT|↑ to MY WAYPOINTS|ENT|↓ to name|ENT. Select the desired
waypoint and press ENT|ENT. Press ↓ to EDIT WAYPOINT|ENT.
2. Latitude: press → to LATITUDE|ENT. Press ↑ or ↓ to change the first
character, then press → to the next character and repeat until the lati-
tude is correct. Press EXIT.
3. Longitude: press ↓ to LONGITUDE|ENT. Press ↑ or ↓ to change the first
character, then press → to the next character and repeat until the lon-
gitude is correct. Press EXIT. To return to the main page display press
EXIT repeatedly.
Selecting a Waypoint
To select a waypoint on the map center the cursor crosshairs on the
waypoint. A red border will appear around the waypoint.
Set a Waypoint by Average Position
A waypoint set by average position is created after several position
readings have been averaged. This boosts waypoint position accuracy
by helping to eliminate errors caused by atmospheric conditions and
other factors.
1. Press WPT|↑ to MY WAYPOINTS|→ to NEW|ENT.
2. Press ↓ or ↑ to AVERAGE POSITION|ENT|press → to CREATE|ENT.
3. Wait while the unit takes points to average for the position. The greater
the number of points, the greater the accuracy. When the desired number
of points accumulates, press ENT to create and save the waypoint.
66
Download from Www.Somanuals.com. All Manuals Search And Download.
4. The Edit Waypoint menu appears. Press EXIT repeatedly to get back
to the main page display.
Set a Waypoint by Projecting a Position
This feature creates a waypoint at a location a specific distance and
bearing from a reference position. The reference position can be a way-
point, map feature or Point of Interest.
1. Press WPT|↑ to MY WAYPOINTS|→ to NEW|ENT.
2. Press ↓ to PROJECTED POSITION|ENT|→ to CREATE|ENT.
3. Press CHOOSE REFERENCE|ENT. Use ↑ and ↓ to select a waypoint, map
feature or Point of Interest. When a selection has been made press ENT.
Press →, ↑ or ↓ to choose a subcategory, then press ENT. Highlight
NAME|ENT. Spell out the name of the desired reference point in the Find
By Name box or press ENT to the find the point in the list below. After
you have selected a point, press ENT. That will launch the waypoint in-
formation window. Highlight SET REFERENCE and press ENT.
4. Press ← ↓ to DISTANCE|ENT. Press ↑ or ↓ to change the first character,
then press → to the next character and repeat until the distance is cor-
rect. Press ENT.
5. Press ↓ to BEARING|ENT. Press ↑ or ↓ to change the first character,
then press → to the next character and repeat until the bearing is cor-
rect. Press ENT.
6. Press ↑ to PROJECT|ENT. The Edit Waypoint menu appears. Press
EXIT|EXIT to get back to the main page display or press EXIT|ENT to
navigate to the new waypoint.
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
68
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5:
System & GPS Setup Options
Alarms
This unit has three GPS alarms: Arrival Alarm, Off Course Alarm and
Anchor Alarm — the only one of the three set to Off by default.
You can set an arrival alarm to flash a warning message and sound a
tone when you cross a preset distance from a waypoint. For example, if
you have the arrival alarm set to .1 mile, the alarm will flash a mes-
sage when you come within .1 mile of your destination.
The off course alarm warns you when your track drifts too far to the
right or left of the course line to your destination. For example, if the
alarm is set to .1 mile, then the alarm flashes a message if you drift .1
miles or more to the right or left of the course line.
The anchor alarm is triggered when you drift outside of a preset radius.
If you are anchored and your boat moves more than .1 miles, the alarm
will flash a message and sound a tone.
Alarms command (left) with Alarm menu at right.
To change alarm settings:
1. Press MENU|MENU|↓ to ALARMS|ENT|ENT.
2. Scroll ↓ or ↑ to select the desired category, then press ENT to turn on
(check) or turn off (uncheck) the desired alarm.
3. To change distance settings, scroll ↓ or ↑ to select the desired cate-
gory, then press → |ENT to activate the distance dialog box. Press ↑ or
↓ to change the first character, then press → to the next character and
69
Download from Www.Somanuals.com. All Manuals Search And Download.
repeat until you are satisfied with the distance setting. If you want to
enable the other alarms, repeat steps 2 and 3.
4. Press EXIT repeatedly to get back to the main page display.
IMPORTANT ALARM NOTES:
Anchor Alarm - The anchor alarm may be triggered even when
you're sitting still. This typically happens when using small − less
than .05 mile − anchor alarm ranges.
Arrival Alarm - If the arrival alarm distance is set to a small num-
ber, the unit may not show navigation data to the next waypoint af-
ter you arrive at the first one. That occurs when you are not able to
come close enough to the first waypoint to trip the arrival alarm.
Check MMC Files and Storage Space
To check MMC Files:
Press MENU|MENU|↓ to BROWSE FILES|ENT. Press ↓ to MMC CARD
INFO|ENT to see the free space on the card.
Main Menu (left) with MMC File Browser at right.
Communications Port Configuration
The unit has one NMEA 0183 version 2.0 compatible communication
port, or com port for short. The Com Port Menu, accessed from the Sys-
tem Setup Menu, allows you to configure the communications port to
send or receive data to another electronic device. The com port can be
used for NMEA or SiRF Binary data transfer.
To set Com Port Configuration:
1. Press MENU|MENU|↓ to SYSTEM SETUP|ENT.
2. Press ↓ to COMMUNICATIONS PORT|ENT.
70
Download from Www.Somanuals.com. All Manuals Search And Download.
Menus for changing Com Port settings.
For connectors and wiring information for another device, see page 15.
For assistance in configuring the unit to communicate with another
device, consult the factory. Customer service phone numbers are in the
back of this manual. Also see the entry below for Configure NMEA.
Configure NMEA
You can configure the unit to use specific NMEA sentences.
1. Press MENU|MENU|↓ to SYSTEM SETUP|ENT.
2. Press ↓ to COMMUNICATIONS PORT|ENT|↓ to CONFIGURE NMEA 0183|ENT.
3. A menu appears showing the prefixes of the available NMEA sen-
tences. A check mark next to a prefix means the prefix is in use. Use ↑
↓, ← → to select a prefix, then press ENT to turn it on or off.
NOTE:
The names of the NMEA sentences are abbreviated in this menu.
These are the functions of the various selectable prefixes:
•
GLL transmits latitude and longitude of present position, time
of position fix, and status.
•
•
•
•
RMC and RMB transmits navigation information messages.
APB transmits autopilot information.
GGA transmits time, position, and fix related data.
GSA and GSV transmits fix mode, DOP values, and satellites in
view information.
•
•
•
DBT transmits the depth below the transducer.
DPT transmits the depth
MTW transmits the water temperature.
71
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
VLW transmits the distance traveled through water as meas-
ured by the paddle wheel.
VHW transmits the water speed as measured by the paddle
wheel.
4. When the desired prefixes are checked or unchecked, press
EXIT|EXIT|EXIT|EXIT to return to the previous page.
Coordinate System Selection
The Coordinate System Menu lets you select the coordinate system to
use when displaying and entering position coordinates.
Menus for changing coordinate system.
To get to Coordinate System Selection:
1. Press MENU|MENU|↓ to GPS SETUP|ENT.
2. Press ↓ to COORDINATE SYSTEM|ENT.
This unit can show a position in degrees (36.14952°); degrees, minutes
and thousandths of a minute (36° 28.700'); or degrees, minutes, seconds
and tenths of a second (36° 28' 40.9"). It can also show position in: UTM
(Universal Transverse Mercator) projection; MGRS (Standard); MGRS
(Standard + 10); Map Fix; Loran TD; British, Irish, Finnish, German,
New Zealand, Swedish, Swiss, Taiwan and Greek grid systems.
UTM's are marked on USGS topographic charts. This system divides
the Earth into 60 zones, each 6 degrees wide in longitude. British,
Irish, Finnish, German, New Zealand, Swedish, Swiss, Taiwan, and
Greek grid systems are the national coordinate system used only in
their respective countries. In order to use these grid systems, you must
be in the respective country. This unit will pick the matching datum for
you when you select the grid. See the entry on Map Datum Selection for
more information.
72
Download from Www.Somanuals.com. All Manuals Search And Download.
The Military Grid Reference System (MGRS) uses two grid lettering
schemes, which are referred to as standard and standard + 10 MGRS
on this unit. Your position and datum in use determines which one to
use. If you use standard and your position is off significantly try the
alternate.
NOTE:
When the position format is changed, it affects the way all positions
are shown on all screens. This includes waypoints.
To change the coordinate system, press ENT while COORDINATE SYSTEM is
highlighted. Use ↑ ↓ to highlight the desired format. Press ENT to select
it.
To setup Loran TD:
NOTE:
If the Loran TD conversion is chosen, you must enter the local Lo-
ran chain identification for the master and slaves. Do this by se-
lecting "Setup Loran TD" at the bottom of the "Coordinate System"
menu and select the ID. Press EXIT to erase this menu.
Setup Loran TD highlighted (left) and Configure Loran TD menu
shown at right.
Map Fix
Map Fix is used with charts or maps. This system asks for a reference
position in latitude/longitude, which you take from a marked location
on the map. It then shows the present position as distance on the map
from that reference point.
For example, if it shows a distance of UP 4.00" and LEFT 0.50", you
then measure up four inches and to the left a half-inch from the refer-
ence point on the map to find your location.
73
Download from Www.Somanuals.com. All Manuals Search And Download.
To configure a map fix:
To use this format, you need to follow these steps in order. Take a map
of the area and determine a reference latitude/longitude.
NOTE:
In order for this system to work, the latitude/longitude lines must
be parallel with the edge of the map. USGS maps are parallel, oth-
ers may not be. Also, this works better with smaller scale maps,
such as 1:24000.
The reference position can be anywhere on the map, but the closer it is
to your location, the smaller the numbers you will be working with.
Once you have decided on a reference position, you can save it as a way-
point. See the waypoint section for information on saving a waypoint.
Save the reference position as a waypoint. Exit the waypoint screens.
1. Press MENU|MENU|↓ to GPS SETUP|ENT.
2. Press ↓ to COORDINATE SYSTEM|ENT.
3. Press ↓ to SETUP MAP FIX|ENT.
The far right figure will appear and MAP SCALE is highlighted. Press ENT
and enter the map's scale. This is generally at the bottom of the paper
map. It's shown as a ratio, like 1:24000. Press EXIT and the unit returns
to the Configure Map Fix screen.
Configure a map fix so the unit can find your position
on a printed chart or topographical map.
Press → to SELECT ORIGIN|ENT to bring up the waypoint and POI list.
Select the waypoint (or a landmark of POI) you saved the reference
point under and press ENT|ENT. Spell out the name of the waypoint,
landmark or POI in the Find By Name box or press ENT to select the
item from the list below. Highlight the waypoint, landmark or POI and
press ENT. The unit displays a waypoint information screen with the
74
Download from Www.Somanuals.com. All Manuals Search And Download.
command SET AS ORIGIN selected. Press ENT and the unit returns to the
Configure Map Fix menu. Finally, press EXIT to close this menu. Now
press ↑ to COORD SYSTEM|ENT, select MAP FIX from the list and press ENT.
Press EXIT repeatedly to get back to the main page display where all
position information now is shown as a distance from the reference
point you chose.
Customize Page Displays
The Satellite Status, Navigation, Map and Sonar pages all have custom-
izable options. These options control what information is viewable on each
page.
Customize Satellite Status Page
While on the Satellite Status Page, press MENU|↓ to CUSTOMIZE|ENT.
The digital data box at the top of the screen will begin to flash.
1. Press ENT if you want to change the data in that box or use ↓ ↑ to
select a different data box to customize.
2. With the desired data box highlighted and flashing, press ENT to ac-
cess the Data Viewer menu. It has five Data Categories: GPS Data,
Navigation, Trip Calculator, Time and Sonar Data.
Customize selected on the Satellite Status Page menu (left). After
choosing a digital data box to customize, the Data Viewer menu will
appear (center). Notice none of the data category internal menus are
visible, denoted by the "+" next to each category. Position Error has
been selected from the GPS Data category (right).
3. Use ↑ ↓ to select a data category, which will have either a "+" or "-" in
front of it. If the desired category is flanked by a "+", a list of data op-
tions will appear when you highlight the category and press ENT.
4. After opening the category, use ↑ ↓ to select the desired data option
and press ENT to turn it on (check) or turn it off (uncheck) and press
EXIT.
5. Use ↑ ↓ to change the data in another digital data box or press EXIT
to return to normal operation.
75
Download from Www.Somanuals.com. All Manuals Search And Download.
GPS Simulator
The GPS simulator simulates real world navigation. It is a great way to
practice using your unit. You can set the starting location by entering
latitude/longitude or from a stored waypoint, map place or POI location.
You can steer the position arrow and change speed on the map by using
the arrow keys — STEER WITH ARROWS command — or by setting the track
and speed in the dialog boxes provided on the simulator menu screen.
To get to the GPS Simulator:
1. Press MENU|MENU|↓ to GPS SETUP|ENT.
2. Press ↓ to GPS SIMULATOR|ENT. The GPS Simulator Menu appears.
GPS Setup Menu (left). GPS Simulator menu (center).
Map Page showing Steer with Arrows dialog boxes (right). The trav-
eler is following a track of 144º at a speed of 71 miles per hour.
Choose the desired settings, then turn on the simulator by highlighting
the GPS SIMULATOR ON box and pressing ENT. Press EXIT repeatedly to get
back to the main page display. A message and tone appear periodically
to remind you the simulator is on. To turn off the simulator, repeat the
steps above or turn off the unit.
If you selected the Steer with Arrows command and want to remove the
dialog boxes from the screen, press EXIT. That will clear the track and
speed boxes without disrupting the simulation and allow you to use the
map cursor.
Simulating Trail or Route Navigation
In Simulator mode, your unit can automatically follow a trail or route
without manual steering if you use these steps:
1. From the Map Page, go to the simulator menu. Pick a STARTING
POSITION at or near the beginning of your trail/route. Enter an approxi-
76
Download from Www.Somanuals.com. All Manuals Search And Download.
mate TRACK (shown in compass degrees) that will point you toward the
start of the trail/route.
2. Set SPEED to zero. Select STEER WITH ARROWS command and press ENT,
which turns on the simulator and returns you to the Map Page.
3. Begin navigating along the trail/route. (If you are close enough to the
first waypoint, the arrival alarm will usually go off as soon as naviga-
tion begins. Press EXIT to clear the alarm.) When navigation starts,
press ↑ to increase speed to the desired setting.
4. Press EXIT to turn off the steering and speed boxes. The unit will now
automatically steer along the trail or route. When you arrive at your
destination, cancel navigation.
Tip:
You can pick any spot on the map to begin a simulation by using
the Initialize GPS command. It allows you to move the position ar-
row to any location on the map. The command is detailed below.
Initialize GPS
In simulator mode, the Initialize GPS command makes the unit operate
as if it is sitting someplace other than its actual location. So you and
your unit could be located in Kansas City, but practice navigating in the
ocean off Islamorada, Florida.
NOTE:
Remember: if you want to run a simulation in a place other than
your current location, you first must Initialize the GPS, then turn
on the GPS Simulator.
1. Press MENU|MENU|↓ to GPS SETUP|ENT|ENT.
2. A message appears, telling you to move the cursor near the desired
location and press ENT. When the message automatically clears, follow
the message instructions.
3. In a moment, your present position marker arrow appears on the
map in the location you selected with the cursor. The unit will consider
that spot as its last known position until changed by either a live satel-
lite lock-on or a new simulator location.
Map Auto Zoom
This receiver has an auto zoom feature that eliminates a lot of the but-
ton pushing common with other brands of GPS receivers. It works in
conjunction with the navigation features.
Start navigating to a waypoint. Then, with the auto zoom mode on, the
unit zooms out until the entire course shows, from the present position
77
Download from Www.Somanuals.com. All Manuals Search And Download.
to the destination waypoint. As you travel toward the destination, the
unit automatically zooms in — one zoom range at a time — keeping
your current position and the destination on the screen.
To turn this feature on from the MAP PAGE, press MENU|↓ to AUTO
ZOOM|ENT|EXIT. Repeat these steps to turn it off.
Map Data
From the Map Data menu, you can turn off the map — which will turn
the map into a GPS plotter — turn on or off pop-up map info boxes,
draw map boundaries and fill water areas with white. You also can
turn on or off Map Overlays, like range rings and latitude and longi-
tude grid lines.
From the Map Page, you can access the Map Data menu by pressing
MENU|↓ to MAP DATA|ENT.
Map Data Menus
Earth Map Detail
From the Map Data menu, highlight EARTH MAP DETAIL and press ENT.
Select the desired level of map detail from four options: Off, Low, Me-
dium or High. After the option is set, press EXIT.
Pop-up Map Information
From the Map Page, press MENU|↓ to MAP DATA|ENT. Press ↓ to POPUP
MAP INFORMATION. With the option highlighted, press ENT to check it (turn
on) and uncheck it (turn off.) After the option is set, press EXIT|EXIT to
return to the page display.
Map Boundaries
From the Map Page, press MENU|↓ to MAP DATA|ENT. Press ↓ to DRAW
MAP BOUNDARIES. With the option highlighted, press ENT to check it (turn
on) and uncheck it (turn off.) After the option is set, press EXIT|EXIT to
return to the page display.
78
Download from Www.Somanuals.com. All Manuals Search And Download.
Fill Water With White
From the Map Page, press MENU|↓ to MAP DATA|ENT. Press ↓ to FILL
WATER WITH WHITE. With the option highlighted, press ENT to check it
(turn on) and uncheck it (turn off.) After the option is set, press
EXIT|EXIT to return to the page display.
Map Overlays (Range Rings; Lat/Long Grid)
The map screen can be customized with four range rings and/or grids
that divide the map into equal segments of latitude and longitude.
Range rings are handy for visually estimating distances on the map. The
ring diameters are based on the current zoom range. At a 100-mile zoom,
the screen will show two rings with your current position in the center.
The large ring touching the left and right sides of the screen is 100 miles
in diameter (same as the zoom range). The second smaller ring is 50
miles in diameter (always 1/2 the zoom range).
The distance from your current position to the smaller ring (the ring's
radius) is 25 miles (always 1/4 the zoom range). With the map cursor,
you can scroll over to see the third and fourth rings. In this example,
the distance to the third ring is 75 miles and distance to the fourth ring
is 100 miles from your current position.
To set range rings: From the Map Data menu, highlight RANGE RINGS
and press ENT to turn them on (check) or turn them off (uncheck). After
the option is set, press EXIT.
To set Lat/Long Grid: From the Map Data menu, highlight LAT/LON
GRID LINES and press ENT to turn them on (check) or turn them off (un-
check). After the option is set, press EXIT repeatedly to get back to the
main page display.
Map Datum Selection
Maps and charts are based on a survey of an area covered by a map or
chart. These surveys are called Datums. Maps created using different
datums will show the same latitude/longitude in slightly different loca-
tions.
All datums have a name. The GPS system is based on the WGS-84 da-
tum, which covers the entire world. Other datums may cover the entire
world or just a small portion of it. By default, your position is shown
with the WGS-84 datum. It, however, can show your position using any
of 191 different datums.
To change the Datum:
1. Press MENU|MENU|↓ to GPS SETUP|ENT|↓ to DATUM SELECTION|ENT.
2. Select the desired datum and press ENT.
79
Download from Www.Somanuals.com. All Manuals Search And Download.
3. To return to the main page display, press EXIT|EXIT.
A list of the datums used by this unit is in the back of this manual.
GPS Setup Menu (left) Map Datum Menu at right.
Map Detail Category Drawn
This menu determines what mapping features are shown on the screen.
This includes, waypoints, trails, icons, cities and highways, etc. You can
turn on or off any of these items, customizing the map to your needs.
To get to Map Categories Drawn:
1. From the Map Page, press MENU|↓ to MAP CATEGORIES DRAWN|ENT.
2. Scroll through the list of categories. Press ENT to turn on (check) or
turn off (uncheck) a category. When a category is on, press → to jump to
the subcategory window. Press ENT to turn on or off subcategories.
3. Press EXIT|EXIT to get back to the main page display.
Map Menu (left). Map Categories Drawn Menu (right).
80
Download from Www.Somanuals.com. All Manuals Search And Download.
Map Orientation
By default, this receiver shows the map with north always at the top of
the screen. This is the way most maps and charts are printed on paper.
In Track Up mode, map shows "N" and arrow to indicate north.
Map orientation shown in north up (left) and track up (right).
This is fine if you are always traveling north. What you see to your left
and right corresponds with the left and ride sides of the map. But if you
travel any other direction, the map does not line up with your view.
To correct this problem track-up mode rotates the map as you turn. So
what you see on the left side of the screen should always be to your left
and so on.
Another option is course-up mode, which keeps the map at the same
orientation as the initial bearing to the waypoint. When either track-up
or course-up modes are on, an "N" shows on the map screen to keep you
aware of which direction is north.
To change map orientation from the Map Page, press MENU|↓ to MAP
ORIENTATION|ENT. Use ↑ ↓ to select the desired mode, then press ENT.
Press EXIT|EXIT to return to the page display.
81
Download from Www.Somanuals.com. All Manuals Search And Download.
Map Menu (left). Map Orientation menu with
the North Up selected (right).
NOTE:
In North Up and Course Up, the present position arrow appears in
the center of the map page. In Track Up, the position arrow appears
centered in the lower third of the page.
NauticPath USA Marine Charts
Your unit can display NauticPath electronic charts on MMCs. They
work just like a MapCreate custom map on a MMC.
Nautical Chart Notes
NauticPath charts contain notes or chart information, represented by cir-
cle-i Chart Note icons on the map display. An example is shown in the
following figure.
NauticPath chart showing Chart Note icon selected by cursor (left).
Note information screen (right).
82
Download from Www.Somanuals.com. All Manuals Search And Download.
To view Chart Note information:
1. Use the arrow keys to move the cursor over a Chart Note icon. When
it's selected, a pop-up name box appears.
2. Press WPT to display the Note Information screen.
3. To scroll through the Chart Note screen, use ↑ ↓ arrow keys to read
the information. To return to the main page display, press EXIT repeat-
edly.
Entrance to Aransas Pass on a NauticPath chart with 8-nautical mile
zoom (left). Remaining images (left to right): same position at 4-
nautical mile, 1-nautical mile and 0.3- nautical mile zoom ranges.
Port Information
NauticPath charts contain Port Services information, represented by
anchor icons on the map display. These icons will appear when you are
zoomed in to a 4-nautical mile range. An example is displayed in the
following figures.
To view Port Services information:
1. Use the arrow keys to move the cursor over a Port Services icon.
When it is selected, a pop-up name box appears.
2. Press WPT to display the Port Services Information screen.The Port
Services information screen for a NauticPath chart contains all the
service information in one window.
3. To scroll through the service information window, use ↑ ↓ to see the
types of services available. To return to the main page display, press
EXIT repeatedly.
83
Download from Www.Somanuals.com. All Manuals Search And Download.
Port Services
icon
Pop-up
name box
NauticPath chart showing Port Services icon selected by cursor. When
first highlighted, the Pop-Up name box appears.
Tidal Current Information
NauticPath charts contain Tidal Current information,
represented at large zoom ranges by a box icon with
the letter "C." These icons will appear when you are
zoomed in to a 6-mile range. The icon stands for a
Tidal Current Station location. An example is displayed on the right.
When you zoom in to a sufficiently small zoom range (0.8 nautical
mile), the icon becomes an animated arrow showing tidal current ve-
locity and direction for the selected tidal station at the present time.
At larger zoom ranges, you can select the boxed "C" icon and it becomes
an animated arrow with a pop-up name box (the name box disappears
after a few seconds). Examples are displayed in the following figures.
To view Tidal Current information:
1. Use the arrow keys to move the cursor over a Tidal Current Station
icon. When it is selected, a pop-up name box appears.
2. Press WPT to display the Tidal Current Information screen.
84
Download from Www.Somanuals.com. All Manuals Search And Download.
Tidal Current
Station icon in
animated mode
Cursor
lines
NauticPath chart showing Tidal Current Station icon selected by cur-
sor (left). Icon animates automatically at .08-mile zoom range (right).
Current Time Line
Velocity
Scale
Slack Water Line
Tide Tables
Current Information screen.
The Tidal Current Information screen displays daily tidal current data
for this station on this date at the present time. The graph at the top of
the screen is an approximate view of the flood and ebb pattern for the
day, from midnight (MN), to noon (NN) to midnight (MN). The velocity
scale at the top left side of the graph changes dynamically based upon
the maximum velocity of the current for that day.
Slack water, the period of little or no current, is represented by the
Slack Water Line (SWL). The flood appears above the SWL and the ebb
appears below the SWL. You can look up tidal current data for other
dates by changing the month, day and year selection boxes.
85
Download from Www.Somanuals.com. All Manuals Search And Download.
To select another date:
1. Use ← → to highlight month, day or year, then press ENT.
2. Use ↑ ↓ to select the desired month, day or year and press ENT.
To clear the information screen, press EXIT.
Tide Information
NauticPath charts contain Tidal Information,
represented at large zoom ranges by a box icon with
the letter "T." These icons will appear when you are
zoomed in to a 6-mile range. The icon stands for a
Tidal Station location. An example is displayed at right.
When you zoom in to a sufficiently small zoom range (0.8 nautical
mile), the icon becomes an animated gauge showing a rising or falling
tidal height for the selected station at the present time. At larger zoom
ranges, you can select the boxed "T" icon and it becomes an animated
gauge with a pop-up name box. The name box disappears seconds.
Tide Station
icon in ani-
mated mode
Cursor
lines
NauticPath chart showing Tide Station icon selected by cursor (left).
Icon animates automatically without selection at the 0.8-mile zoom
range (right). In the example above, the tide is at 0.9 feet and falling,
as shown by the down arrow at the top of the icon.
To view tide information:
1. Use the arrow keys to move the cursor over a tide station icon. When
it is selected, a pop-up name box appears.
2. Press WPT to display the Tide Information screen.
86
Download from Www.Somanuals.com. All Manuals Search And Download.
Current Time Line
Height
Scale
MLLW
Line
Tide
Table
Tide Information screen.
The Tide Information screen displays daily tidal data for this station on
this date at the present time. The graph at the top of the screen is an
approximate view of the tidal range pattern for the day, from midnight
(MN) to noon (NN) to midnight (MN). The dotted line across the graph
is the Mean Lower Low Water line (MLLW).
The height scale on the top right side of the graph changes, based upon
the maximum range of the tide for that day. The MLLW line also ad-
justs its position as the height scale changes.
You can look up tidal data for other dates by changing the month, day
and year selection boxes. To select another date:
1. Use ← → to highlight month, day or year, then press ENT.
2. Use ↑ ↓ to select the desired month, day or year and press ENT.
To clear the information screen, press EXIT.
Navionics Charts
Your unit can also display Navionics electronic charts on MMCs. Like
NauticPath, Navionics charts contain tide and port service information.
NOTE:
The primary operational difference between a NauticPath chart
and a Navionics chart is the way the chart data is set up for dis-
play. NauticPath charts are ready for display as soon as they are
inserted into the unit. Navionics charts must be inserted into the
unit, then selected as a Map Choice option in the Map Data menu.
To display a Navionics chart:
1. Install the Navionics MMC in the memory card compartment and
turn on the unit. (For full card install instructions, see Sec. 2.)
87
Download from Www.Somanuals.com. All Manuals Search And Download.
2. From the Map Page, press MENU|↓ to MAP DATA|ENT|↓ to MAP
CHOICE|ENT. Select the Map Name, then press ENT|EXIT|EXIT.
South Chesapeake Navionics selected from Map Choice menu (right).
WARNING:
You should never format the MMC containing your
Navionics chart. Formatting the MMC will permanently
erase the chart from the card.
Overlay Data
On any Page display but Status you can float additional data of your
own choosing in your display window. For example, if you left your
watch at home, you could add the local time to your display. Or, if you
wanted to see details about your route and trip, you could show your
bearing, course, average speed and trip distance.
The various data available from your unit are divided into categories in
the Overlay Data menu. These categories include GPS Data, Naviga-
tion, Trip Calculator and Time.
You can select items from any of these categories for display, in any
combination — the category divisions are there only to help you sort
through the information.
88
Download from Www.Somanuals.com. All Manuals Search And Download.
Overlay Data, with "Navigation," "Trip Calculator"
and "Time" categories expanded.
To overlay information on your screen:
1. While on the Navigation Page or a Map Page, press MENU|↓ to
OVERLAY DATA|ENT.
2. You'll see a list of the overlay data currently shown, if any. Select
(ENTER TO ADD) and press ENT. The data viewer shows information cate-
gories with "+" or "–" symbols next to each category name. A category
with a "+" next to it is expandable, meaning its contents are currently
hidden.
Selecting the category name and pressing ENT will show the category's
contents, so you can choose items within it. An expanded category (one
with a "–" next to its name) can be collapsed to hide its contents, and
make more room on your screen. Just select the category name and
press ENT.
3. Expand any categories that might contain information you want to
display. Then press ↓ or ↑ to select a display option.
4. With the option highlighted, press ENT to check it (turn on) and un-
check it (turn off). As you turn categories on, data will float in your dis-
play window. Every Page display has a maximum number of items you
can float on your display using the Overlay Data command.
5. After all options are set, press EXIT|EXIT to return to the page display.
89
Download from Www.Somanuals.com. All Manuals Search And Download.
From Overlay Data Shown (left) press ENT to see Data Viewer (center).
Select a category and press ENT; then select information to float on
screen and press ENT (right).
To remove overlaid data:
1. While on the Page that shows the item or items you want to remove,
press MENU|↓ to OVERLAY DATA|ENT.
2. You'll see a list of the overlay data currently displayed. Select the
item you want to remove from your display and press ENT|ENT to re-
move the data. To remove another item, select the item and press
ENT|ENT.
3. When you have finished removing all the items you want from the
screen, press EXIT to return to the page display.
Overlay Data Shown, with Date option selected (left). Press ENT to ac-
cess REMOVE option (center). Press ENT again to remove item and return
to Overlay Data Shown (right).
To move overlaid data:
You may find it useful to rearrange data that is floating in your display
window.
90
Download from Www.Somanuals.com. All Manuals Search And Download.
1. From one of the Map Pages, press MENU|↓ to OVERLAY DATA|ENT.
2. You'll see a list of the overlay data currently displayed. Select the
item you want to move and press ENT|→ to MOVE|ENT.
3. The data begins to flash on your screen. Use any combination of →,
←, ↑ and ↓ to move the data to a new location on the screen.
4. When satisfied, press EXIT|EXIT.
NOTE:
The Customize command and the Overlay Data command both use
the same information categories. The difference between the two
commands is that Customize changes only the data boxes on your
display, and Overlay Data floats information anywhere on the
screen. See Customize Page Displays, on page 75, for information
on customizing data boxes.
Pop-up Help
Help is available for virtually all of the menu labels on this unit. By
highlighting a menu item and leaving it highlighted for a few seconds, a
"pop-up" message appears that describes the function of the menu item.
This feature is on by default.
To set up Popup Help: Press MENU|MENU|↓ to SYSTEM SETUP|ENT|↓
to POPUP HELP. With the option highlighted, press ENT to check it (turn
on) and uncheck it (turn off.) After the option is set, press EXIT|EXIT to
return to the page display.
System Setup Menu (left) with Pop-up Help command highlighted. At
right, this example shows the Pop-up Help message for the Initialize
GPS command, located on the Status Page menu.
91
Download from Www.Somanuals.com. All Manuals Search And Download.
Reset Options
To reset all features to their factory defaults:
1. Press MENU|MENU|↓ to SYSTEM SETUP|ENT|↓ to RESET OPTIONS|ENT|←
to YES|ENT.
NOTE:
Reset Options does not erase any waypoints, routes, icons or plot trails.
System Menu with Reset Options command selected.
Require WAAS
You can choose to have WAAS signals automatically factored into every
position reading. The default setting, Off, uses WAAS automatically,
but does not require it to yield a position.
To Require WAAS:
1. Press MENU|MENU|↓ to GPS SETUP|ENT|↓ to REQUIRE WAAS|ENT.
2. To return to the main page display, press EXIT|EXIT.
3. Repeat Step 1 to turn off WAAS requirement.
Require WAAS command on the GPS Setup Menu.
92
Download from Www.Somanuals.com. All Manuals Search And Download.
Screen Contrast and Brightness
To access the Screen menu, press MENU|MENU|ENT.
The CONTRAST slider bar is already selected. Press ← → to adjust the
contrast.
To adjust the display's brightness:
Press ↓ to BRIGHTNESS. Use ← → to adjust the brightness of the display.
Screen Command (left). Screen menu with Contrast selected (center).
Normal highlighted on Display Mode menu (right).
To adjust the screen's display mode:
Press ↓ to DISPLAY MODE|ENT. Press ↑ ↓ to select mode|EXIT.
Set Language
This unit's menus are available in 10 languages: English, French, Ger-
man, Spanish, Italian, Danish, Swedish, Russian, Dutch and Finnish.
To select a different language:
1. Press MENU|MENU|↓ to SYSTEM SETUP|ENT.
2. Press ↓ to SET LANGUAGE|ENT.
3. Use ↓ ↑ to select a different language and press ENT. Menus now ap-
pear in the language you selected.
Set Local Time
To access the Set Local Time menu, you must first acquire your posi-
tion, then press MENU|MENU|↓ to SYSTEM SETUP|ENT|↓ to SET LOCAL
TIME|ENT.
To set Local Time: Press ENT. Use ↑ ↓ to change the first character,
then press → to move the cursor to the next character. Repeat until the
time is correct and press ENT.
93
Download from Www.Somanuals.com. All Manuals Search And Download.
To set the Month: Press ↓ to MONTH|ENT. Use ↑ ↓ to select the month
and press ENT.
To set the Day: Press ↓ → to DAY|ENT. Press ↑ ↓ to select the day and
press ENT.
To set the Year: Press ↓ → to YEAR|ENT. Press ↑ ↓ to select the year
and press ENT.
To set Time Format: Press ↓ to TIME FORMAT, highlight an option and
press ENT to turn it on or off.
To set Date Format: Press ↓ → to DATE FORMAT, highlight an option
and press ENT to turn it on or off.
The last field in this menu is CONFIG DST. This feature sets up the unit
to automatically adjust with the time change resulting from Daylight
Saving Time. You may select which set of rules matches DST in your
region or just accept the default. You should only have to configure DST
once.
Once you have each field set the way you want, press EXIT repeatedly to
get back to the main page display.
Show WAAS Alarm
When the signal is available, your unit will automatically use WAAS to
boost the accuracy of a position fix. When the WAAS signal is lost or
acquired, a message appears. Since the U.S. government is still devel-
oping the WAAS system, it is not unusual for a GPS/WAAS receiver to
frequently lose and reacquire its lock on a WAAS satellite. That can
result in the alarm repeatedly going off. If you want, turn off the WAAS
Acquired/Lost alarm without affecting how the unit uses WAAS.
To turn off WAAS alarm:
1. Press MENU|MENU|↓ to GPS SETUP|ENT|↓ to SHOW WAAS ALARM.
2. Press ENT to turn it on (check) or turn it off (uncheck). After the op-
tion is set, press EXIT|EXIT to return to the page display.
3. To turn the alarm on again, repeat Steps 1 and 2.
Software Version Information
From time to time, Eagle updates the operating system software in
some of its products. These software upgrades are usually offered to
customers as free downloads from our web site, www.eaglegps.com.
These upgrades make the unit perform better or introduce a new fea-
ture or function. You can find out what software version is running in
your unit by using the Software Information command.
94
Download from Www.Somanuals.com. All Manuals Search And Download.
Main Menu (left) with Software Information command selected.
The Software Information screen is shown at right.
1. Press MENU|MENU|↓ to SYSTEM SETUP|ENT|↓ to SOFTWARE
INFORMATION|ENT.
2. Read the information displayed on the screen.
3. To return to the last page displayed, press EXIT|EXIT|EXIT.
Sounds and Alarm Sound Styles
Sounds triggered by key strokes and alarms can be adjusted:
You first press MENU|MENU|↓ to SOUNDS|ENT.
Sounds command, left. At right, the Sounds menu.
Once in the Sounds menu:
To set Key Press Sounds: With the option highlighted, press ENT to
check it (turn on) and uncheck it (turn off.) After the option is set, press
EXIT|EXIT to return to the page display.
95
Download from Www.Somanuals.com. All Manuals Search And Download.
To set Alarm Sounds: Press ↓ to ALARM SOUNDS. With the option high-
lighted, press ENT to check it (turn on) and uncheck it (turn off.) After
the option is set, press EXIT|EXIT to return to the page display.
To set Alarm Volume: Press ↓ to VOLUME. Press → or ← to move the
bar. The left end of the scale is low volume; the right end is high volume.
After the option is set, press EXIT|EXIT to return to the page display.
To set Alarm Style: Press ↓ to ALARM STYLE|ENT. Press ↑ or ↓ to
change the style, then press ENT. After the option is set, press
EXIT|EXIT to return to the page display.
Track Smoothing
This is a factory setting on the GPS Setup menu that should always be
left on. When stopped or traveling at slow speeds, like walking or troll-
ing, Track Smoothing prevents wandering of trails, the steering arrow,
compass rose and a map in track-up mode.
Track Smoothing option, turned on.
Trail Options
There are several options you can use with trails. Some affect all trails,
other options can be applied to a particular trail. You can change the
way trails are updated, display or hide trails, create a new trail, delete
a trail, etc.
General Trail Options
To access the Trails Menu press MENU|MENU|↓ to MY TRAILS|ENT.
96
Download from Www.Somanuals.com. All Manuals Search And Download.
Main Menu (left). Trails Menu (center). Trail Options (right).
Delete All Trails
From the Trails Menu, press → to DELETE ALL|ENT|← to YES|ENT.
Update Trail Option
This menu lets you change the way the trail updates occur.
From the Trails Menu, press → to TRAIL OPTIONS|ENT. With UPDATE ACTIVE
TRAIL highlighted, press ENT to turn it on (check) or turn it off (uncheck).
WARNING:
If you uncheck the Update Trail option, automatic trail
creation and recording will be turned off. You must turn
it back on to record trails. The default setting is on.
Update Trail Criteria
The options are automatic, time or distance. When it is in the default
mode, the unit does not update the plot trail while you are traveling in
a straight line. Once you deviate from a straight line, the unit drops a
plot point onto the trail. This conserves plot trail points. If a plot trail
uses all the available points allotted to it, the beginning points are
taken away and placed at the end of the trail.
From the Trails Menu, press → to OPTIONS|ENT. Select one of the three
Update Criteria options — Auto, Time or Distance — and press ENT.
Trail Update Rate
A trail updated by time has a range of 1 to 9999 seconds. The default is
3 seconds. The range for updating a trail by distance is 0.01
mile/nm/km to 9.99 mile/nm/km. The default is 0.10 mi.
When time or distance are chosen as the update criteria for a trail, a
dialog box will appear, allowing you to input the desired update rate or
distance. Select the dialog box and press ENT. Use ↑ ↓ to change the
first character, then press → to the next character and repeat until the
entry is correct. Press EXIT to return to the Trail Options Menu.
97
Download from Www.Somanuals.com. All Manuals Search And Download.
Update Rate setting (left) and Update Distance setting (right).
Trail Name highlighted (left). Edit Trail menu (center). Trails menu
with New Trail highlighted (right).
Specific Trail Options
Delete Trail
From the Trails Menu, press ↓ to trail name|ENT. The Edit Trail menu
appears. Press → to DELETE TRAIL|ENT|← to YES|ENT.
New Trail
To manually start a new trail, in the Trails Menu, highlight NEW TRAIL is
highlighted and press ENT.
Trail Visibility and Other Trail Options
The name, maximum number of points in the trail, activity and visibil-
ity are all changed on the Edit Trail menu screen. The Active setting
determines whether the unit is recording new points for a trail. Related
trail functions are discussed in further detail under the Trails topic in
Sec. 7, Advanced GPS Operations.
98
Download from Www.Somanuals.com. All Manuals Search And Download.
Transparency set to 0 percent (left), 50 percent (center)
and 100 percent (right).
Transparency
Use the transparency menu to adjust the transparency of menu win-
dows. A high transparency setting allows you to continue monitoring
the screen's display while working with a menu. A low transparency
usually will make menu text easier to read, at the cost of watching your
display.
To adjust Transparency level:
Press MENU|MENU|↓ to TRANSPARENCY|ENT. The TRANSPARENCY slider bar
appears. Press ↑ or ↓ to adjust the level of transparency. Press EXIT
when it is set at the desired level.
Units of Measure selected on System Setup menu (left).
Units of Measure Menu (right).
99
Download from Www.Somanuals.com. All Manuals Search And Download.
Units of Measure
This menu sets the speed, distance, depth, temperature and heading
units.
To change the units:
Press MENU|MENU|↓ to SYSTEM SETUP|ENT|ENT.
To set Units of Measure: Select a category you would like to change.
Highlight the desired unit of measure option under the category and
press ENT. Repeat those steps for each category that has a unit of
measure option you would like to change. After all options are set, press
EXIT repeatedly to return to the main page display.
Units of Measure selected on System Setup menu (left).
Units of Measure Menu (right).
100
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 6: Searching
NOTE:
The background map loaded in your unit lets you to search for U.S.
Interstate Highway exits and exit services, as well as some land
features, including cities and lakes. For a full set of searchable land
features, including landmarks, streets, addresses and Points of In-
terest, you must load your own high-detail custom map produced
with our MapCreate 6 software. For a complete description of what
detail is found in the background map and custom MapCreate
maps, see page 32. (Remember, our pre-made FreedomMaps con-
tain all the same detail found in custom-made MapCreate maps.)
This unit's varied search functions all begin with either the Find Way-
point menu or the Map Page menu. Press WPT and the Find Waypoint
menu appears for waypoints and Points of Interest (POI). From the
Map Page, press MENU and the Map Page menu appears for streets,
addresses and highway exits.
Find Waypoint menu (left) and Map Page menu at right.
IMPORTANT NOTES:
The search commands let you look up items by name or search for
the item nearest to you. When you search, the unit looks for items
in the vicinity of your current position. If you are using the unit in-
doors, in simulator mode or otherwise haven't locked on to satel-
lites, the unit looks near the last known position.
To search in some other location, use the arrow keys to center the
map cursor where you want to look. When the cursor is active, the
unit always begins searching at the cursor location.
101
Download from Www.Somanuals.com. All Manuals Search And Download.
In search results, the distance and bearing to the selected item will
be calculated from the current position. In the case of a cursor
search, the search results show distance and bearing from the cur-
sor, but an individual waypoint's information screen shows distance
and bearing from the current (or last known) position.
Find Addresses
1. From the Map Page, press MENU|↓ to FIND ADDRESS|ENT.
2. Press ENT to search in the Address field.
3. To enter an address number, press ↑ or ↓ to change the first
number, then press → to move the cursor to the next number and re-
peat until the number is correct, then press ENT.
Find Address Menu (left) and Find By Name at right.
4. To enter a street name, press ↓ to STREET|ENT. You can spell out
the name in the street selection box. Press ↑ or ↓ to change the first
letter, then press → to move the cursor to the next letter and repeat
until the name is correct, then press ENT|ENT.
5. To enter a city name, press ↓ to CITY|ENT. You will be asked if you
want to find addresses only within a particular city. This option is de-
signed so you can limit an address search to a single city if necessary
(see the following note).
If you select yes, there are two options: A. You can spell out the city
name in the top selection box. Press ↑ or ↓ to change the first letter, then
press → to move the cursor to the next letter and repeat until the name
102
Download from Www.Somanuals.com. All Manuals Search And Download.
is correct, then press ENT|ENT. B. Jump down to the lower selection list
by pressing ENT, then press ↓ or ↑ to select a city name from the list,
then press ENT. The city name you selected is now in the city field.
NOTE:
We recommend that you do not enter a city name unless the list you
are given is too large when searching without it. This unit can ac-
tually search quicker without a city listed save time by not entering
a city name.
Find City field (left), Search in particular city only option (center)and
Find City by name at right.
6. When the necessary search fields are filled in, press ↓ to FIND
ADDRESS|ENT. Your unit asks you to wait while it searches for the ad-
dress. If an address is not in the database, a message appears saying
the address could not be found.
7. The unit will display a list of addresses. If the address you are look-
ing for is highlighted at the top of the list, press ENT. If not, use ↓ and ↑
to select the correct address from the list, then press ENT. The Map
Page will then appear with the location selected by the cursor.
8. To navigate to the address, press MENU|ENT|EXIT and the unit will
begin showing navigation information to the address pointed out by the
cursor. If you are only looking up an address (not navigating), just
press EXIT to return to the previous page.
Tip:
If the address also happens to be an item in the Point of Interest
database, you can look up the item's phone number in the Waypoint
Information list. With the address location selected by the cursor on
the map, press WPT. The POI's Waypoint Information window ap-
pears, with the Go To Waypoint command highlighted. If you want
to go ahead and navigate to the POI address, just press ENT|EXIT.
103
Download from Www.Somanuals.com. All Manuals Search And Download.
Find Any Item Selected by Map Cursor
On the Map Page, with a POI or map feature selected by the cursor
press WPT. To return to the previous page, press EXIT.
Map Page (left) showing location of the address on the map, high-
lighted by cursor. The address (right) is a business in the POI data-
base, so you can display the POI information window, then navigate to
it.
NOTE:
Since the Go To waypoint command is highlighted, you can navi-
gate to the selected POI by pressing ENT|EXIT while in the POI
Waypoint Information screen.
Find Interstate Highway Exits
1. From the Map Page, press MENU|↓ to HIGHWAY EXITS|ENT, which calls
up the Find Exit menu.
Find Highway Exits command (left) and Find Exit menu at right.
104
Download from Www.Somanuals.com. All Manuals Search And Download.
2. First, select a highway name by pressing ENT, which calls up the
Find By Name menu. There are two highway search options. First, you
can spell out the highway name in the top selection box. Press ↑ or ↓
to change the first letter, then press → to move the cursor to the next
letter and repeat until the name is correct, then press ENT|ENT. Or you
can jump down to the lower selection list by pressing ENT, then press ↓
or ↑ to select a highway from the list, then press ENT.
Find By Name menu.
3. Once you have selected a highway name you can then select an exit.
Press ↓ to switch to the Exit List, then press ↓ or ↑ until you highlight
the exit, then press ENT.
Find Exit menu, with an exit selected in the Exit List.
105
Download from Www.Somanuals.com. All Manuals Search And Download.
4. In the Exit Information screen you have two choices. Press ENT to
navigate or "go to" the exit or press →|ENT to find the exit on the map.
"Go To Exit" option (left) and "Find On Map" option at right.
Tip:
You can also look up additional information on the Exit Services lo-
cated near this exit. Press ↓ to SERVICES|press ↓ or ↑ to select Serv-
ice Name|ENT.
Exit Information screen (left) general location
and amenities information at right.
Find Map Places or Points of Interest (POI)
1. Press WPT, press ↓ or ↑ to select a category, then press ENT. To nar-
row your search, press → or ← to select a subcategory before pressing
ENT. You will have two options; search by Name and search by Nearest.
106
Download from Www.Somanuals.com. All Manuals Search And Download.
Find Waypoint menu with Lodging POI category selected.
2. To search by nearest POI select NEAREST and press ENT. The Find BY
menu will show a "calculating" screen, then a list of the nearest POI's
will appear. Press ↓ or ↑ to the selected POI and press ENT to call up
the POI's Waypoint Information screen.
Find Waypoint menu (left) with category POI-Lodging and subcate-
gory for Bed & Breakfast highlighted. Find By screen (center) and cal-
culated results for Find By Nearest results shown at right.
3. To search for a POI by name select NAME|ENT. This will give you two
options. You can spell out the POI in the top selection box. Press ↑ or ↓
to change the first letter, then press → to move the cursor to the next
letter and repeat until the name is correct, then press ENT|ENT. Or
press ↓ down to the Find In List screen by pressing ENT, then press ↓ or
↑ to select a POI from the list, then press ENT to call up the POI's Way-
point Information screen.
107
Download from Www.Somanuals.com. All Manuals Search And Download.
A list of Find by Nearest (left) and Waypoint Information menu at
right.
4. When the POI's Waypoint Information screen is displayed, you can
choose "Go To Waypoint" or "Find On Map" by pressing ↓ or ↑ |ENT.
Find Streets or Intersections
Find a Street
1. From the Map Page, press MENU|↓ to FIND STREETS|ENT and the Find
Streets Menu appears.
Find Streets command (left) with Find Streets menu at right.
2. You must first fill in a street name in the First Street dialog box.
Press ENT to display the Find By Name menu. You have two search op-
tions. You can spell out the street in the top selection box. Press ↑ or ↓
108
Download from Www.Somanuals.com. All Manuals Search And Download.
to change the first letter, then press → to move the cursor to the next
letter and repeat until the name is correct, then press ENT|ENT. Or you
can jump down to the lower box and pick a street from the selection list.
Press ENT, then press ↓ or ↑ to select a street from the list and press
ENT.
Find Street By Name menu. Spell out name in
the top box or select from the list in the lower box.
3. The Find Streets menu reappears with the street you're searching for
in the First Street box. To search for that street, press ↓ to FIND FIRST
STREET|ENT. A message appears asking you to wait while the unit finds
the street. When the Streets Found list appears, press ↑ or ↓ to select the
street you are searching for and press ENT.
Map Page showing results of a street search.
The cursor points to the located street.
109
Download from Www.Somanuals.com. All Manuals Search And Download.
If you want to navigate to the found street at the cursor location, just
press MENU|ENT|EXIT.
Find an Intersection
You must enter one street in the First Street dialog box and enter the
next street in the Second Street dialog box.
1. From the Map Page, press MENU|↓ to FIND STREETS|ENT and the Find
Streets Menu appears.
2. You must fill in a street name in the First Street dialog box. Press ENT
to display the Find By Name menu. There are two options. You can spell
out the street in the top selection box. Press ↑ or ↓ to change the first
letter, then press → to move the cursor to the next letter and repeat until
the name is correct, then press ENT|ENT. The second option is to jump
down to the lower box and pick a street from the selection list. Press
ENT, then press ↓ or ↑ to select a street from the list and press ENT.
3. The Find Streets menu reappears with the street you're searching for
in the First Street box.
4. Now fill in the second street. Press ↓ to SECOND STREET|ENT and the
Find By Name menu appears again. Just like before, there are two op-
tions You can spell out the second street in the top selection box. Press
↑ or ↓ to change the first letter, then press → to move the cursor to the
next letter and repeat until the name is correct, then press ENT|ENT.
The second option is to jump down to the lower box and pick the second
street from the selection list. Press ENT, then press ↓ or ↑ to select a
street from the list and press ENT.
5. The Find Streets menu reappears with the first and second street
dialog boxes filled in. In this example, we selected I-44 as our second
street. You could now use similar techniques to select a city or Zip code,
but your search will probably be faster if you leave those boxes blank.
You can specify a city and/or Zip code later on to narrow the search if
the resulting list is too long.
110
Download from Www.Somanuals.com. All Manuals Search And Download.
Find Intersection command highlighted on the left and the Find First
Street command highlighted at right.
6. To search for the intersection of the two streets, press ↓ to FIND
INTERSECTION|ENT. A message appears asking you to wait while the unit
finds the intersection. When the Intersections Found list appears, press
↑ or ↓ to select the intersection you are searching for and press ENT.
7. The Map Page appears, with the cursor pointing to the found inter-
section. The intersection in our example is shown below.
Map Page showing results of an intersection search.
The cursor points to the located intersection.
If you want to navigate to the found intersection, just press
MENU|ENT|EXIT.
111
Download from Www.Somanuals.com. All Manuals Search And Download.
Find Waypoints
1. Press WPT|↑ to MY WAYPOINTS|ENT.
2. When searching for the nearest waypoint, press ENT. If searching for
the waypoint by name, highlight NAME then ENT. (To search by name,
jump to step 5.)
Find By Nearest command (left). Find by Name command (center).
List of the nearest waypoints (right).
3. When you are searching for the nearest waypoint, a list of waypoints
appears with the closest location highlighted at the top of the list and
the one furthest from you at the bottom of the list.
4. To see location information on the closest waypoint, press ENT and the
Waypoint Information screen appears.
A. To navigate to the waypoint, press ENT. The Go To Waypoint
command is already highlighted. The unit will show navigation in-
formation to the waypoint.
B. To find the waypoint, press ↓ to FIND ON MAP|ENT. The Map Page
appears with the cursor highlighting the found waypoint.
To clear these menus and return to the previous page, press EXIT re-
peatedly.
5. If you are looking by name, there are two options. You can spell out
the name in the top selection box. Press ↑ or ↓ to change the first letter,
then press → to move the cursor to the next letter and repeat until the
name is correct, then press ENT|ENT. Or you can jump down to the
lower selection list by pressing ENT, then press ↓ or ↑ to select a way-
point from the list, then press ENT. The waypoint information screen
appears.
112
Download from Www.Somanuals.com. All Manuals Search And Download.
Find By Name menu (left). Waypoint Information screen (center). The
cursor crosshairs are centered on the desired waypoint (right).
A. To navigate to the waypoint, press ENT. The Go To Waypoint
command is already highlighted. The unit will show navigation in-
formation to the waypoint.
B. To find the waypoint, press ↓ to FIND ON MAP|ENT. The Map Page
appears with the cursor crosshairs centered on the found waypoint.
113
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
114
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 7: Supplemental Material
Datums Used by This Unit
WGS 1984
Default
Zaire, Zambia and
Zimbabwe
Australian Geodetic
1984 - Australia &
Tasmania
Adindan
Mean for Ethiopia,
Sudan
Arc 1950 - Botswana
Arc 1950 - Burundi
Arc 1950 - Lesotho
Arc 1950 - Malawi
Arc 1950 - Swaziland
Arc 1950 - Zaire
Ayabelle Lighthouse -
Djibouti
Adindan
Burkina Faso
Bellevue (IGN) -
Efate & Erromango
Islands
Adindan
Cameroon
Bermuda 1957 -
Bermuda
Adindan
Ethiopia
Bissau - Guinea-
Bissau
Bogota Observatory -
Colombia
Arc 1950 - Zambia
Arc 1950 - Zimbabwe
Adindan
Mali
Adindan
Senegal
Arc 1960 - Mean for
Kenya, Tanzania
Bukit Rimpah - Indo-
nesia (Bangka & Be-
litung Islands)
Adindan
Sudan
Ascension Island
1958 - Ascension
Island
Camp Area Astro -
Antarctica (McMurdo
Camp Area)
Afgooye
Somalia
Astro Beacon E 1945
- Iwo Jima
Campo Inchauspe -
Argentina
Ain el Abd 1970
Bahrain
Astro DOS 71/4 - St.
Helena Island
Canton Astro 1966 -
Phoenix Islands
Ain el Abd 1970
Saudi Arabia
Astro Tern Island
(FRIG) 1961 - Tern
Island
Cape - South Africa
Anna 1 Astro 1965
Cocos Islands
Cape Canaveral -
Bahamas, Florida
Astronomical Station
1952 - Marcus Island
Antigua Island Astro
1943; Antigua (Lee-
ward Islands)
Carthage - Tunisia
Switzerland
Australian Geodetic
1966 - Australia &
Tasmania
Arc 1950; Mean for
Botswana, Lesotho,
Malawi, Swaziland,
Chatham Island Astro
1971; New Zealand
(Chatham Island)
115
Download from Www.Somanuals.com. All Manuals Search And Download.
Chua Astro
Paraguay
European 1950
England, Channel
Islands, Ireland,
Scotland, Shetland
Islands
L.C. 5 Astro 1961
Cayman Brac Island
Corrego Alegre
Brazil
Leigon
Ghana
Dabola
Guinea
European 1950
Finland, Norway
Liberia 1964
Liberia
Djakarta (Batavia)
Indonesia (Sumatra)
European 1950
Greece
Luzon
Philippines (Exclud-
ing Mindanao)
DOS 1968
New Georgia Islands
(Gizo Island)
European 1950
Iran
Luzon
Philippines (Min-
danao)
European 1950
Italy (Sardinia)
Easter Island 1967
Easter Island
Mahe 1971
Mahe Island
European 1950
(Sicily)
European 1950
Mean for Austria,
Belgium, Denmark,
Finland, France,
European 1950
Malta
Massawa
Ethiopia (Eritrea)
West Germany, Gi-
braltar, Greece, Italy,
Luxembourg, Neth-
erlands, Norway,
Portugal, Spain,
Ireland 1965
Ireland
Merchich
Morocco
ISTS 061 Astro 1968
South Georgia Is-
lands
Midway Astro 1961
Midway Islands
Sweden, Switzerland
Minna
European 1950
Mean for Austria,
Denmark, France,
West Germany,
Netherlands, Swit-
zerland
ISTS 073 Astro 1969
Diego Garcia
Cameroon
Minna
Nigeria
Johnston Island 1961
Johnston Island
Montserrat Island
Kandawala
Sri Lanka
Astro 1958; Montser-
rat (Leeward Islands)
European 1950
Mean for Iraq, Israel,
Jordan, Lebanon,
Kuwait, Saudi Arabia,
Syria
Kerguelen Island
1949
Kerguelen Island
M’Poraloko
Gabon, Nahrwan,
Oman (Masirah Is-
land)
European 1950
Cyprus
Kertau 1948
West Malaysia &
Singapore
Nahrwan
Saudi Arabia
European 1950
Egypt
Kusaie Astro 1951
Caroline Islands
Nahrwan
United Arab Emirates
116
Download from Www.Somanuals.com. All Manuals Search And Download.
Naparima BWI
Trinidad & Tobago
North American 1927
Canada (Alberta,
British Columbia)
Old Hawaiian
Mean for Hawaii,
Kauai, Maui, Oahu
North American 1927
Mean for Antigua,
Barbados, Barbuda,
Caicos Islands,
North American 1927
Canada (Manitoba,
Ontario)
Old Hawaiian
Hawaii
Cuba, Dominican
Republic, Grand
Cayman, Jamaica,
Turks Islands
Old Hawaiian
Kauai
North American 1927
Canada (New
Brunswick, New-
foundland, Nova
Scotia, Quebec)
Old Hawaiian
Maui
North American 1927
Mean for Belize,
Costa Rica, El Sal-
vador, Guatemala,
Honduras, Nicaragua
Old Hawaiian
Oahu
North American 1927
Canada (Northwest
Territories, Sas-
katchewan)
Oman
Oman
North American 1927
Mean for Canada
North American 1927
Canada (Yukon)
Ordinance Survey
Great Britain 1936 -
Mean for England,
Isle of Man, Scotland,
Shetland Islands,
Wales
North American 1927
Mean for CONUS
(Continental United
States)
North American 1927
Canal Zone
North American 1927
Mean for CONUS
(East of Mississippi
River) including Lou-
isiana, Missouri, Min-
nesota
North American 1927
Cuba
Ordinance Survey
Great Britain 1936 -
England
North American 1927
Greenland (Hayes
Peninsula)
Ordinance Survey
Great Britain 1936 -
England, Isle of Man,
Wales
North American 1927
Mean for CONUS
(West of Mississippi
River)
North American 1927
Mexico
North American 1983
Alaska, Canada,
CONUS
Ordinance Survey
Great Britain 1936 -
Scotland, Shetland
Islands
North American 1927
Alaska
North American 1983
Central America,
Mexico
North American 1927
Bahamas (Except
San Salvador Island)
Ordinance Survey
Great Britain 1936 -
Wales
Observaorio Metereo
1939; Azores (Corvo
& Flores Islands)
North American 1927
Bahamas (San Sal-
vador Island)
Pico de las Nieves
Canary Islands
Old Egyptian 1907
Egypt
Pitcairn Astro 1967
Pitcairn Island
117
Download from Www.Somanuals.com. All Manuals Search And Download.
Point 58
Sweden
Tokyo
Mean for Japan, Ko-
rea, Okinawa
South American 1969
Chile
Santo (DOS)
1965 Espirito Santo
Island
South American 1969
Colombia
Tokyo
Japan
South American 1969
Ecuador
Tokyo
Korea
Sao Braz
Azores (Sao Miguel,
Santa Maria Islands)
South American 1969
Ecuador (Baltra, Ga-
lapagos)
Tokyo
Sapper Hill 1943
Okinawa
East Falkland Island
South American 1969
Guyana
Tristan Astro 1968
Tristan da Cunha
Schwarzeck
Nambia
South American 1969
Paraguay
South American 1969
Peru
Viti Levu 1916
Fiji (Viti Levu Island)
Selvagem Grande
Salvage Islands
Wake
SGS 85
Soviet Geodetic
System 1985
South American 1969
Trinidad & Tobago
Eniwetok 1960
Marshall Islands
South American 1969
Mean for Argentina,
Bolivia, Brazil, Chile,
Colombia, Ecuador,
Guyana, Paraguay,
Peru, Trinidad & To-
bago, and Venezuela
South American 1969
Venezuela
Wake Island Astro
1952
Wake Atoll
South Asia
Singapore
WGS 1972
Global Definition
Tananarive Obser-
vatory 1925; Mada-
gascar
South American 1969
Argentina
Yacare
Uruguay
South American 1969
Bolivia
Timbalai 1948
Brunei, East Malay-
sia (Sabah, Sarawak)
Zanderij
Suriname
South American 1969
Brazil
118
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC Compliance
This device complies with Part 15 of the U.S. Federal Communi-
cations Commission (FCC) Rules. Operation is subject to the fol-
lowing two conditions: (1) this device may not cause harmful in-
terference, and (2) this device must accept any interference re-
ceived, including interference that may cause undesired opera-
tion.
Changes or modifications not expressly approved by the manu-
facturer could void the user's authority to operate the equip-
ment.
Note:
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable pro-
tection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the in-
structions, may cause harmful interference to radio communica-
tions. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of
the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
Consult the factory customer service department for help.
119
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
120
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
121
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
122
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
123
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
124
Download from Www.Somanuals.com. All Manuals Search And Download.
EAGLE DATABASES LICENSE AGREEMENT
THIS IS a LEGAL AGREEMENT BETWEEN THE END-USER WHO FIRST
PURCHASES THIS PRODUCT AS a CONSUMER ITEM FOR PERSONAL,
FAMILY, OR HOUSEHOLD USE ("YOU") AND EAGLE ELECTRONICS, a
DIVISION OF LEI, THE MANUFACTURER OF THIS PRODUCT ("WE",
"OUR", OR "US"). USING THE PRODUCT ACCOMPANIED BY THIS
LICENSE AGREEMENT CONSTITUTES ACCEPTANCE OF THESE TERMS
AND CONDITIONS. IF YOU DO NOT ACCEPT ALL TERMS AND
CONDITIONS, PROMPTLY RETURN THE PRODUCT WITHIN 30 DAYS OF
PURCHASE. PLEASE RETURN USING THE ENCLOSED UPS SHIPPING
LABEL AND INCLUDE: PROOF OF PURCHASE, NAME, ADDRESS, AND
PHONE NUMBER. YOUR PURCHASE PRICE AND ANY APPLICABLE
TAXES WILL BE REFUNDED. PLEASE ALLOW 4-6 WEEKS TO PROCESS
YOUR REFUND.
1. This License Agreement applies to the one or more databases that
your product may contain. We refer to these singly as a "Database"
and together as the "Databases." Your product may thus include the
"WBS Database" which contains worldwide background surface
mapping data, the "SmartMap Database" which contains inland
mapping data, or other Databases.
2. The Databases that your product may contain are licensed, not sold.
We grant to you the nonexclusive, nonassignable right to use these
Databases for supplemental navigation reference purposes, but only
as long as you comply with the terms and conditions of this License
Agreement. We reserve the right to terminate this license if you vio-
late any aspect of this License Agreement. You are responsible for
using official government charts and prudent navigation for safe
travel.
3. The Databases housed in your product are protected by the copy-
right notices appearing on the product or its screen(s). You may
NOT modify, adapt, translate, reverse engineer, decompile, disas-
semble, rent, lease, or resell any Database, and you may NOT create
derivative works based upon any Database or its contents.. Any un-
authorized reproduction, use, or transfer of a Database may be a
crime and may subject you to damages and attorney fees.
4. This License Agreement will terminate immediately without prior
notice from us if you fail to comply with or violate any of the provi-
sions of this Agreement. Upon termination, you will promptly return
all products containing one or more Databases to us.
5. Prices and programs are subject to change without notice.
6. This License Agreement shall be governed by the laws of the State of
Oklahoma and comprises the complete and exclusive understanding
between you and us concerning the above subject matter.
125
Download from Www.Somanuals.com. All Manuals Search And Download.
DATABASES LIMITED WARRANTY
"We", "our", or "us" refers to Eagle Electronics, a division of LEI, the manufac-
turer of this product. "You" or "your" refers to the first person who purchases
the product as a consumer item for personal, family, or household use. The Da-
tabases Limited Warranty applies to the one or more databases that your prod-
uct may contain. We refer to each of these as a "Database" or together as the
"Databases." Your product may thus include the "WBS Database" which con-
tains worldwide background surface mapping data, the "SmartMap Database"
which contains inland mapping data, or other Databases.
We warrant to you that we have accurately compiled, processed, and repro-
duced the portions of the source material on which the Databases are based.
However, we are under no obligation to provide updates to the Databases, and
the data contained in the Databases may be incomplete when compared to the
source material. WE MAKE NO EXPRESS OR IMPLIED WARRANTY OF
ANY KIND ABOUT THE ACCURACY OF THE SOURCE MATERIAL ITSELF,
INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR a PARTICULAR PURPOSE.
If there is a defect in any Database, your exclusive remedy shall be, at our op-
tion, either a refund of the price you paid for the product containing the defec-
tive Database or a replacement of such product. WE WILL NOT UNDER ANY
CIRCUMSTANCES BE LIABLE TO ANYONE FOR ANY SPECIAL,
CONSEQUENTIAL, INCIDENTAL, OR OTHER INDIRECT DAMAGE OF
ANY KIND.
Some states do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitations or exclusions may not apply to you.
This warranty does NOT apply in the following circumstances: (1) when the
product has been serviced or repaired by anyone other than us, (2) when the
product has been connected, installed, combined, altered, adjusted, or handled
in a manner other than according to the instructions furnished with the prod-
uct, (3) when any serial number has been effaced, altered, or removed, or (4)
when any defect, problem, loss, or damage has resulted from any accident, mis-
use, negligence, or carelessness, or from any failure to provide reasonable and
necessary maintenance in accordance with the instructions of the owner’s man-
ual for the product.
We reserve the right to make changes or improvements in our products from
time to time without incurring the obligation to install such improvements or
changes on equipment or items previously manufactured.
This warranty gives you specific legal rights and you may also have other rights
which may vary from state to state.
Your remedies under this warranty will be available so long as you can show in
a reasonable manner that the defect occurred within one (1) year from the date
of your original purchase, and we must receive your warranty claim no later
than 30 days after such 1-year period expires. Your claim must be substanti-
ated by a dated sales receipt or sales slip.
126
Download from Www.Somanuals.com. All Manuals Search And Download.
EAGLE ELECTRONICS
FULL ONE-YEAR WARRANTY
"We," "our," or "us" refers to EAGLE ELECTRONICS, a division of LEI, the manufac-
turer of this product. "You" or "your" refers to the first person who purchases this product
as a consumer item for personal, family, or household use.
We warrant this product against defects or malfunctions in materials and workmanship,
and against failure to conform to this product's written specifications, all for one (1) year
from the date of original purchase by you. WE MAKE NO OTHER EXPRESS
WARRANTY OR REPRESENTATION OF ANY KIND WHATSOEVER CONCERNING
THIS PRODUCT. Your remedies under this warranty will be available so long as you can
show in a reasonable manner that any defect or malfunction in materials or workman-
ship, or any non-conformity with the product's written specifications, occurred within one
year from the date of your original purchase, which must be substantiated by a dated
sales receipt or sales slip. Any such defect, malfunction, or non-conformity which occurs
within one year from your original purchase date will either be repaired without charge
or be replaced with a new product identical or reasonably equivalent to this product, at
our option, within a reasonable time after our receipt of the product. If such defect, mal-
function, or non-conformity remains after a reasonable number of attempts to repair by
us, you may elect to obtain without charge a replacement of the product or a refund for
the product. THIS REPAIR, OR REPLACEMENT OR REFUND (AS JUST DESCRIBED)
IS THE EXCLUSIVE REMEDY AVAILABLE TO YOU AGAINST US FOR ANY
DEFECT, MALFUNCTION, OR NON-CONFORMITY CONCERNING THE PRODUCT
OR FOR ANY LOSS OR DAMAGE RESULTING FROM ANY OTHER CAUSE
WHATSOEVER. WE WILL NOT UNDER ANY CIRCUMSTANCES BE LIABLE TO
ANYONE FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR OTHER
INDIRECT DAMAGE OF ANY KIND.
Some states do not allow the exclusion or limitation of incidental or consequential dam-
ages, so the above limitations or exclusions may not apply to you.
This warranty does NOT apply in the following circumstances: (1) when the product has
been serviced or repaired by anyone other than us; (2) when the product has been con-
nected, installed, combined, altered, adjusted, or handled in a manner other than ac-
cording to the instructions furnished with the product; (3) when any serial number has
been effaced, altered, or removed; or (4) when any defect, problem, loss, or damage has
resulted from any accident, misuse, negligence, or carelessness, or from any failure to
provide reasonable and necessary maintenance in accordance with the instructions of the
owner's manual for the product.
We reserve the right to make changes or improvements in our products from time to time
without incurring the obligation to install such improvements or changes on equipment
or items previously manufactured.
This warranty gives you specific legal rights and you may also have other rights which
may vary from state to state.
REMINDER: You must retain the sales slip or sales receipt proving the date of your
original purchase in case warranty service is ever required.
EAGLE ELECTRONICS
PO BOX 669, CATOOSA, OK 74015
(800) 324-1354
127
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Obtain Service…
…in the USA:
We back your investment in quality products with quick, expert service
and genuine Eagle replacement parts. If you're in the United States
and you have technical, return or repair questions, please contact the
Factory Customer Service Department. Before any product can be re-
turned, you must call customer service to determine if a return is nec-
essary. Many times, customer service can resolve your problem over the
phone without sending your product to the factory. To call us, use the
following toll-free number:
800-324-1354
8 a.m. to 5 p.m. Central Standard Time, M-F
Eagle Electronics may find it necessary to change or end our shipping
policies, regulations, and special offers at any time. We reserve the right
to do so without notice.
…in Canada:
If you're in Canada and you have technical, return or repair questions,
please contact the Factory Customer Service Department. Before any
product can be returned, you must call customer service to determine if
a return is necessary. Many times, customer service can resolve your
problem over the phone without sending your product to the factory. To
call us, use the following toll-free number:
800-661-3983
905-629-1614 (not toll-free)
8 a.m. to 5 p.m. Eastern Standard Time, M-F
…outside Canada and the USA:
If you have technical, return or repair questions, contact the dealer in
the country where you purchased your unit. To locate an Eagle dealer
near you, visit our web site at www.eaglegps.com or consult your tele-
phone directory for listings.
128
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessory Ordering Information
for all countries
To order Eagle accessories such as power cables or MMC cards,
please contact:
1) Your local marine dealer or consumer electronics store. Most quality dealers
that handle marine electronic equipment or other consumer electronics should be
able to assist you with these items.
To locate an Eagle dealer near you visit our web site at www.eaglegps.com or
consult your telephone directory for listings.
2) U.S. customers: LEI Extras Inc., PO Box 129, Catoosa, OK 74015-0129
Call 1-800-324-0045 or visit our web site www.lei-extras.com.
3) Canadian customers can write:
Lowrance/Eagle Canada, 919 Matheson Blvd. E. Mississauga, Ontario L4W2R7
or fax 905-629-3118.
Shipping Information
If it becomes necessary to send a product for repair or replacement, you must
first receive a return authorization number from Customer Service. Products
shipped without a return authorization will not be accepted. When shipping, we
recommend you do the following:
1. Please do not ship the knobs or mounting bracket with your unit.
2. If you are sending a check for repair, please place your check in an envelope
and tape it to the unit.
3. For proper testing, include a brief note with the product describing the
problem. Be sure to include your name, return shipping address and a daytime
telephone number. An e-mail address is optional but useful.
4. Pack the unit in a suitable size box with packing material to prevent any
damage during shipping.
5. Write the Return Authorization (RA) number on the outside of the box
underneath your return address.
6. For your security, you may want to insure the package through your
shipping courier. Eagle does not assume responsibility for goods lost or
damaged in transit.
Download from Www.Somanuals.com. All Manuals Search And Download.
Visit our web site:
www.eaglesonar.com
Eagle Pub. 988-0143-881
Printed in USA 121905
Copyright © 2005
All Rights Reserved
LEI-Eagle
Download from Www.Somanuals.com. All Manuals Search And Download.
|