19" LED TV
DX-19E310NA15
WE ARE GOING GREEN!
A copy of your User Guide is not provided in the box but is available
online.
Enter your model number in the box under
Manual, Firmware, Drivers & Product Information,
then click Search.
You can also find additional troubleshooting information
IMPORTANT INFORMATION
Before using your new product, please read these instructions to prevent any damage.
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Important safety instructions
DX-19E310NA15
Lightning
For added protection for your device receiver during a lightning
storm, or when it is left unattended and unused for long periods of
time, unplug it from the power outlet and disconnect any antenna or
cable system. This helps prevent property damage and personal injury
from lightning and power line surges.
Important safety instructions
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Power lines
An outside antenna system should not be located in the vicinity of
overhead power lines or other electric light or power circuits, or where
it can fall into such power lines or circuits. When installing an outside
antenna system, extreme care should be taken to keep from touching
such power lines or circuits as contact with them might be fatal.
This symbol indicates that
dangerous voltage constituting a
risk of electric shock is present
within your TV. This label is located
on the back of your TV.
Handling the LCD panel
•
Your TV’s screen is made of glass. Do not drop your TV or hit, jolt,
or press hard against the LCD panel. If the screen breaks, be
careful of broken glass.
If the LCD panel is broken, make absolutely sure that you do not
touch the liquid in the panel. This may cause skin inflammation.
If the liquid gets in your mouth, immediately gargle, rinse, and
consult with your doctor. Also, if the liquid gets in your eyes or
touches your skin, consult with your doctor after rinsing for at
least 15 minutes or longer in clean water.
This symbol indicates that there
are important operating and
maintenance instructions in the
literature accompanying your TV.
•
•
1
2
3
4
5
6
7
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with a dry cloth.
Do not block any ventilation openings. Install in accordance with
the manufacturer's instructions.
Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers) that
produce heat.
Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades with one
wider than the other. A grounding type plug has two blades and a
third grounding prong. The wide blade or the third prong are
provided for your safety. If the provided plug does not fit into your
outlet, consult an electrician for replacement of the obsolete
outlet.
Replacement parts
When replacement parts are required, make sure that the service
technician uses replacement parts specified by the manufacturer that
have the same characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock, personal injury, or other
hazards.
8
Safety check
After completing any service or repair to this device, ask the service
technician to perform routine safety checks to determine that your TV
is in correct operating condition.
9
Power source
Operate your TV only from the type of power source indicated on the
marking label. If you are not sure of the type of power supplied to your
home, consult an electrician or your local power company.
10 Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
Cautions
11 Only use attachments/accessories specified by the manufacturer.
Damage requiring service
12 Use only with a cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid
injury from tip-over.
Unplug this TV from the power outlet and refer servicing to qualified
service personnel under the following conditions:
•
•
•
•
When the power supply cord or plug is damaged or frayed.
If liquid has been spilled or objects have fallen into your TV.
If your TV has been exposed to rain or water.
If your TV does not operate normally by following the operating
instructions. Adjust only those controls that are covered by the
operating instructions because incorrect adjustment of other
controls may result in damage and will often require extensive
work by a qualified technician to restore your TV to its normal
operation.
13 Unplug this apparatus during lightning storms or when unused
for long periods of time.
14 Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way, such
as power-supply cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has
been dropped.
•
•
If your TV has been dropped or damaged in any way.
When your TV exhibits a distinct change in performance.
15 The wall plug is the disconnecting device. The plug must remain
Outdoor antenna grounding
readily operable.
If an outside antenna or cable system is connected to your TV, make
sure that the antenna or cable system is grounded to provide some
protection against voltage surges and built-up static charges. Article
810 of the National Electrical Code, ANSI/NFPA No. 70, provides
information with respect to correct grounding of the mast and
supporting structure, grounding of the lead-in wire to an antenna
discharge unit, size of grounding conductors, location of the
antenna-discharge unit, connection to grounding electrodes, and
requirements for the grounding electrode.
16 Remote control batteries should not be exposed to excessive heat
such as sunshine, fire, or the like.
17 The apparatus should not be exposed to dripping or splashing,
and no objects filled with liquids, such as vases, should be placed
on the apparatus.
Warnings
Electric shock hazard
To reduce the risk of fire or electric shock, do not remove any cover or
expose the device to rain or moisture. No user-serviceable parts are
inside. Refer servicing to qualified service technicians.
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Troubleshooting
DX-19E310NA15
Antenna lead-in wire
Grounding clamp
Problem
No power
Solution
1
2
3
4
5
•
•
•
Make sure that the power cord is correctly connected to your TV
and a power outlet.
1
2
Unplug the power cord, wait 60 seconds, then plug the cord back
in and turn on your TV.
Antenna discharge unit
Grounding conductors
Ground clamps
Other devices (for example, surround sound receiver, external
speakers, fans, or hair dryers) may be interfering with your TV.
Try turning off one device at a time to determine which device is
causing interference. After you have determined which device is
causing interference, move it further from the TV to eliminate
the interference.
3
4
5
6
Power service grounding
electrode system
6
7
7
“No signal” error
message is displayed
Electric service equipment
•
•
•
Press INPUT and make sure that you have selected the correct
input for the device or service you are trying to use.
If you are using a cable or satellite box, use the remote that came
with that box to change channels.
Make sure that you have the correct input selected to view
channels from the cable or satellite box.
Note to CATV system installer
Article 820 of the National Electrical Code, ANSI/NFPA No. 40 provides
guidance for correct grounding. Specifically, it states that the cable
ground must be connected to the grounding system of the building
as close to the point of cable entry as practical.
After Auto Channel
Search, there are no
channels
•
Reception can vary by channel depending on the broadcast
power level of a given station. Contact your cable or satellite TV
provider.
Condensation
•
•
Make sure that the antenna or cable/satellite TV is connected
securely to your TV.
Moisture will form on the TV if the TV is brought from cool
surroundings into a warm room or if the temperature of the room rises
suddenly. When this happens, the TV's performance may be impaired.
To prevent this, let the TV stand in its new surroundings for about an
hour before switching it on, or make sure that the room temperature
rises gradually.
Condensation may also form during the summer if the TV is exposed
to the breeze from an air conditioner. In such cases, change the
location of the TV.
Try replacing the cable between the antenna/cable or
cable/satellite box and your TV.
One or more channels
do not display.
•
•
Make sure that the channels are not blocked. See “Setting
parental control levels” in the online User Guide.
Make sure that the channels are not hidden. The channel may
have been deleted from the channel list. You can tune to the
channel by pressing the number buttons or you can add the
channel back to the channel list. See “Hiding channels” in the
online User Guide.
Mobile telephone warning
To avoid interference with your TV picture and sound, operating
problems, or even damage, keep your cordless and cellular telephones
away from the TV.
•
•
•
If you are using a cable or satellite box, use the remote that came
with that box to change channels.
Make sure that you have the correct input selected to view
channels from the cable or satellite box.
End of life directives
If you are using an antenna, the digital channel signal may be
low. To check the digital channel signal strength, see “Checking
the digital signal strength” in the online User Guide.
Your TV contains tin-lead solder. Disposal of this material may be
regulated for environmental reasons. Your TV also contains material
that can be recycled and reused.
Password is lost.
•
•
•
Enter 9999 to access parental controls, then set a new password.
See “Setting or changing the password” in the online User Guide.
Non-active pixels
The LCD panel contains almost 3 million thin film transistors, which
provide exceptionally sharp video quality. Occasionally, a few
non-active pixels may appear on the screen as a fixed blue, green, or
red point. These non-active pixels do not adversely affect the
performance of your TV, and are not considered defects.
Some settings cannot
be accessed.
If a setting is grayed, the setting is not available in the current
video input mode.
TV cabinet creaks.
When the TV is in use, the temperature rises naturally and may
cause the cabinet to expand or contract which can cause a
creaking noise. This is not a malfunction.
Troubleshooting
Control buttons do
not work
•
•
Make sure that the Button Lock option is set to Off. See
“Locking control buttons” in the online User Guide.
Unplug the power cord, wait a few seconds, then plug the cord
back in and turn on your TV.
Warning
Do not try to repair your TV yourself. Contact
authorized service personnel.
TV keeps turning off
•
Make sure that the sleep timer is not turned on. See “Setting the
sleep timer” in the online User Guide.
Problem
Solution
Remote control does
not work.
Notes
•
•
•
Make sure that the power cord is correctly connected to your TV
•
If the problem is not solved by using these
troubleshooting instructions, turn off your TV,
then turn it on again.
Additional troubleshooting information is in
your online User Guide. Go to
and a power outlet.
Make sure that there are no obstructions between the remote
control and the remote control sensor on the front of the TV.
Point the remote control directly at the remote control sensor on
your TV. For the location of the remote control sensor, see
“Front” in the online User Guide.
Make sure that the batteries are installed correctly. See
“Installing remote control batteries” in the online User Guide.
Replace dead batteries with new batteries. See “Installing
remote control batteries” in the online User Guide.
•
www.dynexproducts.com, click Support &
Service, enter your model number in the box
under Manual, Firmware, Drivers & Product
Information, then click Search.
•
•
Trouble programming
your existing
universal remote
control.
•
•
•
•
See instructions and a table of common codes in “Programming
a different universal remote control” in the online User Guide.
Codes are subject to change. For up to date codes, go to
Replace dead batteries with new batteries. Refer to the User
Guide that accompanied your universal remote control.
Refer to the User Guide that accompanied your universal remote
control and contact the manufacturer if problems persist.
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Specifications
DX-19E310NA15
Audio
Specifications
Number: 2
Watts per channel: 2.5W
Specifications are subject to change without notice.
Dimensions and weight
Speakers
Power
17.8 × 13.5 × 2 in. (45.2 × 34.2 × 5.2 cm)
On: 30W
Standby: <1W
Without stand
With stand
4.5 lbs. (2.2 kg)
Power consumption
17.8 × 13.5 × 6.4 in. (45.2 × 34.3 × 16.3 cm)
5.3 lbs. (2.4 kg)
Power input
DC 12V, 2.5A
Miscellaneous
Screen
OSD languages
INlink
English, French, Spanish
Screen size measured
diagonally
18.5 in.
No
Game Mode
No
Display type
LED
60Hz
ENERGY STAR qualified
Internet connectable
TV base screws
V-Chip (version 2.0)
Sleep timer
Channel labeling
No
Panel 60 Hz vs.120 Hz
Display resolution
Panel resolution
Aspect ratio
No
720p
M4 type (8 mm length) (4 pcs)
1366 (H) × 768 (V)
16:9
Yes
Yes
Yes
Contrast ratio
(typical)–panel
500:1
Dynamic contrast ratio–
list value
TV brightness (minimum)
cd/m2
VESA mount (mm)
(horizontal × vertical)
VESA mount screws
20,000:1
100 × 100
M4 type
140 nits
Comb filter
3d y/c digital
Note
Response time
Horizontal viewing angle
Vertical viewing angle
5 ms
90°
The length of the wall-mount screws vary
depending on the wall-mount bracket you
purchased. See the instructions that came with
the wall-mount bracket for screw lengths.
65°
Display resolutions/VGA scan rates
Legal notices
HDMI suggested resolutions
Component video suggested
resolutions
720p, 480p, 480i
720p, 480p, 480i
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Tuner
Analog
Digital
NTSC
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
ATSC, 8-VSB, Clear-QAM
Inputs
2 (side)
E-EDID compliant
HDCP compliant
HDMI
Component video
Composite video
1 (back)
1 (back)
•
•
•
Reorient or relocate the receiving antenna.
Shared with component Y
Yes
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Shared audio (component
and composite)
PC/VGA
•
Consult the dealer or an experienced radio/TV technician for help.
No
No
Warning
3.5mm PC audio input
Changes or modifications not expressly approved by the party responsible for
1 (side)
HDMI1 (DVI) jack
Supports Video Only
compliance could void the user's authority to operate the equipment.
DVI
Cables
Connections to this device must be made with shielded cables with metallic
RF/EMI connector hoods to maintain compliance with FCC Rules and
Regulations.
1 (side)
USB
Supports JPEG and firmware upgrade
Antenna/Cable
1 (back)
Canadian Notice
CAN ICES-3 (B)/NMB-3(B)
Outputs
Standard Television Receiving Apparatus — Appareil de réception télévision
Video
No
ordinaire, Canada BETS-7 / NTMR-7
Analog audio/Headphone
Digital audio
WiFi
1 (side)
IC Statement
1 (coaxial) (side)
This device complies with Industry Canada licence—exempt RSS standard(s).
No
No
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
Ethernet
This equipment complies with IC radiation exposure limits set forth for an
uncontrolled environment.
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Legal notices
DX-19E310NA15
HDMI
Open Source
The terms HDMI and HDMI High-Definition
Font name: Arimo
Multimedia Interface, and the HDMI Logo are
trademarks or registered trademarks of HDMI
Licensing LLC in the United States and other countries.
Version 1.23
Copyright 2013 Steve Matteson
Licensed under the Apache License, Version 2.0 (the “License”); you may not
use this file except in compliance with the License. You may obtain a copy of
Unless required by applicable law or agreed to in writing, software distributed
under the License is distributed on an “AS IS” BASIS, WITHOUT WARRANTIES OR
CONDITIONS OF ANY KIND, either express or implied. See the License for the
specific language governing permissions and limitations under the License.
Dolby Laboratories
Manufactured under license from Dolby
Laboratories. Dolby and the double-D symbol are
trademarks of Dolby Laboratories.
If you require additional information please call the Dynex support line at
1-800-305-2204.
Download from Www.Somanuals.com. All Manuals Search And Download.
7
One-year limited warranty - Dynex Televisions
DX-19E310NA15
•
•
Failures or Damage caused by any contact including but not limited to
liquids, gels or pastes.
One-year limited warranty -
Dynex Televisions
Definitions:
Up to three (3) pixel failures (dots that are dark or incorrectly illuminated)
grouped in an area smaller than one tenth (1/10) of the display size or up
to five (5) pixel failures throughout the display. (Pixel based displays may
contain a limited number of pixels that may not function normally.)
Problems with delay in motion or action of video images while playing
first-person style video games.
•
REPAIR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS YOUR
EXCLUSIVE REMEDY FOR BREACH OF WARRANTY. DYNEX SHALL NOT BE LIABLE
FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR THE BREACH OF
ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT, INCLUDING, BUT
NOT LIMITED TO, LOST DATA, LOSS OF USE OF YOUR PRODUCT, LOST BUSINESS
OR LOST PROFITS. DYNEX PRODUCTS MAKES NO OTHER EXPRESS WARRANTIES
WITH RESPECT TO THE PRODUCT, ALL EXPRESS AND IMPLIED WARRANTIES
FOR THE PRODUCT, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED
WARRANTIES OF AND CONDITIONS OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE WARRANTY PERIOD
SET FORTH ABOVE AND NO WARRANTIES, WHETHER EXPRESS OR IMPLIED,
WILL APPLY AFTER THE WARRANTY PERIOD. SOME STATES, PROVINCES AND
JURISDICTIONS DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED
WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU. THIS
WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE
OTHER RIGHTS, WHICH VARY FROM STATE TO STATE OR PROVINCE TO
PROVINCE.
Contact Dynex:
For customer service please call:
US & Canada 1-800-305-2204
DYNEX is a trademark of Best Buy and its affiliated companies.
Registered in some countries.
Dynex Products ("Dynex") warrants to you, the original purchaser of this new
Dynex-branded television ("Product"), that the Product shall be free of defects
in the original manufacturer of the material or workmanship for a period of one
(1) year from the date of your purchase of the Product ("Warranty Period"). For
this warranty to apply, your Product must be purchased in the United States or
Canada from a Best Buy or Future Shop authorized dealer of Dynex brand
products only that are packaged with this warranty statement.
How long does the coverage last?
The Warranty Period lasts for 1 year (365 days) from the date you purchased the
Product. Your purchase date is printed on the receipt you received with the
Product.
What does this warranty cover?
During the Warranty Period, if the original manufacture of the material or
workmanship of the Product is determined to be defective by an authorized
Dynex repair center or store personnel, Dynex will (at its sole option): (1) repair
the Product with new or rebuilt parts; or (2) replace the Product at no charge
with new or rebuilt comparable products or parts. Products and parts replaced
under this warranty become the property of Dynex and are not returned to
you. If service of Products or parts are required after the Warranty Period
expires, you must pay all labor and parts charges. This warranty lasts as long as
you own your Dynex Product during the Warranty Period. Warranty coverage
terminates if you sell or otherwise transfer the Product.
Distributed by Best Buy Purchasing, LLC
7601 Penn Ave South, Richfield, MN 55423 U.S.A.
©2014 Best Buy. All rights reserved.
Made in China
How to obtain warranty service?
If you purchased the Product at a Best Buy or Future Shop retail store location
and your television Product has a screen size of less than 42 inches, please take
your original receipt and the Product to any Best Buy or Future Shop store.
Make sure that you place the Product in its original packaging or packaging
that provides the same amount of protection as the original packaging. If you
purchased the Product from a Best Buy or Future Shop online web site, mail
your original receipt and the Product to the address listed on the web site.
Make sure that you put the Product in its original packaging or packaging that
provides the same amount of protection as the original packaging.
To obtain in-home warranty service for a television with a screen 42 inches or
larger, in the United States call 1-888-BESTBUY, Canada call 1-866-BESTBUY for
Future Shop call 1-800-663-2275. Call agents will diagnose and correct the
issue over the phone or will have an Dynex-approved repair technician
dispatched to your home.
Where is the warranty valid?
This warranty is valid only in the United States and Canada at Best Buy or
Future Shop branded retail stores or websites to the original purchaser of the
product in the county where the original purchase was made.
What does the warranty not cover?
This warranty does not cover:
•
•
•
•
•
•
•
•
•
•
Customer instruction/education
Installation
Set up adjustments
Cosmetic damage
Damage due to acts of God, such as power surges
Accident(s)
Misuse, unintentional or intentional
Abuse, unintentional or intentional
Negligence
Commercial purposes/use, including but not limited to use in a place of
business or in communal areas of a multiple dwelling condominium or
apartment complex, or otherwise used in a place of other than a private
home.
•
•
Modification of any part of the Product, including the antenna
Plasma display panel damaged by static (non-moving) images applied for
lengthy periods (burn-in).
•
•
•
Damage due to incorrect operation or maintenance
Connection to an incorrect voltage or power supply
Outages, static or other problems with over-the-air reception of television
broadcast signals.
•
Attempted repair by any person not authorized by Dynex to service the
Product
•
•
•
Products sold "as is" or "with all faults"
Consumables, including but not limited to batteries (i.e. AA, AAA, C etc.)
Products where the factory applied serial number has been altered or
removed
•
Loss or Theft of this product or any part of the product
Download from Www.Somanuals.com. All Manuals Search And Download.
US and Canada Market - (800) 305-2204
Distributed by Best Buy Purchasing, LLC
7601 Penn Ave. South, Richfield, MN 55423 U.S.A.
© 2014 BBY Solutions, Inc. All rights reserved.
DYNEX is a trademark of BBY Solutions, Inc. Registered in some countries. All other products and
brand names are trademarks of their respective owners.
Made in China
V1 14-0559
ENGLISH
Download from Www.Somanuals.com. All Manuals Search And Download.
|