LCD Data Video Projector
User’s Manual
MODEL 8789H
Information in this Guide may change due to product improvements. To obtain the latest
and look at the specific model SUPPORT or DOWNLOADS section.
DUKANE CORP AV SERVICE DEPT
2900 Dukane Drive
St Charles, IL 60174
800-676-2487 / 630-762-4032
Fax 630-584-5156
403-8789H-GENERAL-00
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector
8789H
User's Manual (concise)
Thank you for purchasing this projector.
Please read through this manual before using this product, in order to use safely
and utilize well the product.
WARNING ►Before using this product, be sure to read all manuals for this
product. See “Using the CD manual” ( 15) to read the manuals in the CD.
After reading them, store them in a safe place for future reference.
►Heed all the warnings and cautions in the manuals or on the product.
►Follow all the instructions in the manuals or on the product.
NOTE • In this manual, unless any comments are accompanied, “the
manuals” means all the documents provided with this product, and “the product”
means this projector and all the accessories came with the projector.
Contents
First of all............................................ 2 Connecting power supply................... 8
Entries and graphical symbols explanation......2
Turning on the power.......................... 8
Adjusting the projector's elevator ....... 9
Important safety instruction ..............................2
Regulatory notices.............................. 3 Displaying the picture....................... 10
About Electro-Magnetic Interference................3
Turning off the power........................ 11
Replacing the lamp........................... 12
About Waste Electrical and Electronic Equipment...4
Contents of package........................... 4 Cleaning and replacing the air filter.. 14
Preparations....................................... 5 Using the CD manual ....................... 15
Loading batteries into the remote control.........5
Specifications ................................... 16
Arrangement....................................... 6 Troubleshooting
Connecting your devices.................... 7
- Warranty and after-service........... 17
1
Download from Www.Somanuals.com. All Manuals Search And Download.
First of all
Entries and graphical symbols explanation
The following entries and graphical symbols are used for the manuals and the
product as follows, for safety purpose. Please know their meanings beforehand,
and heed them.
WARNING This entry warns of a risk of serious personal injury or even death.
CAUTION This entry warns of a risk of personal injury or physical damage.
NOTICE This entry notices of fear of causing trouble.
Important safety instruction
The followings are important instructions for safely using the product. Be sure to
follow them always when handling the product. The manufacturer assumes no
responsibility for any damage caused by mishandling that is beyond normal usage
defined in these manuals of this projector.
WARNING ►Never use the product in or after an abnormality (ex. giving
off smoke, smelling strange, took a liquid or an object inside, broken, etc.) If an
abnormality should occur, unplug the projector urgently.
►Situate the product away from children and pets.
►Do not use the product when there is fear of a thunderbolt.
►Unplug the projector from the power outlet if the projector is not used for the
time being.
►Do not open or remove any portion of the product, unless the manuals direct
it. For internal maintenance, leave it to your dealer or their service personnel.
►Use only the accessories specified or recommended by the manufacturer.
►Modify neither the projector nor accessories.
►Let neither any things nor any liquids enter to the inside of the product.
►Do not wet the product.
►Do not place the projector where any oils, such as cooking or machine oil,
are used. Oil may harm the product, resulting in malfunction, or falling from the
mounted position.
►Apply neither a shock nor pressure to this product.
- Do not place the product on an unstable place such as the uneven surface or
the leaned table.
- Do not place the product unstably. Place the projector so that it does not
protrude from the surface where the projector is placed on.
- Remove all the attachments including the power cord and cables, from the
projector when carrying the projector.
►Do not look into the lens and the openings on the projector, while the lamp is
on.
►Do not approach the lamp cover and the exhaust vents, while the projection
lamp is on. Also after the lamp goes out, do not approach them for a while, since
too hot.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Regulatory notices
About Electro-Magnetic Interference
In CANADA
This Class B digital apparatus complies with Canadian ICES-003.
In the US, and other places where the FCC regulations are applicable
Declaration of Conformity
Trade name
Model Number
HITACHI / Dukane
CPX8 / 8789H
Responsible Party Hitachi America, Ltd.
Address
900 Hitachi way, Chula Vista, CA 91914-3556 U.S.A.
Telephone Number +1 -800-225-1741
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.This equipment has
been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
INSTRUCTIONS TO USERS: This equipment complies with the requirements of
FCC (Federal Communication Commission) equipment provided that the following
conditions are met. Some cables have to be used with the core set. Use the
accessory cable or a designated-type cable for the connection. For cables that
have a core only at one end, connect the core to the projector.
CAUTION: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Regulatory notices (continued)
About Waste Electrical and Electronic Equipment
The mark is in compliance with the Waste Electrical and Electronic
Equipment Directive 2002/96/EC (WEEE).
The mark indicates the requirement NOT to dispose the equipment
including any spent or discarded batteries or accumulators as unsorted
municipal waste, but use the return and collection systems available.
If the batteries or accumulators included with this equipment, display
the chemical symbol Hg, Cd, or Pb, then it means that the battery has a
heavy metal content of more than 0.0005% Mercury or more than, 0.002%
Cadmium, or more than 0.004% Lead.
Contents of package
Your projector should come with the items
MY SOURCE/
VIDEO COMPUTER DOC.CAMERA
(1)
(4)
(5)
ASPECT
AUTO SEARCH BLANK
MAGNIFY FREEZE
ON
PAGE
UP
VOLUME
㧗
shown below. Check that all the items are
included. Require of your dealer immediately if
any items are missing.
DOWN
OFF
KEYSTONE
MY BUTTON
MUTE
MENU
1
2
POSITION
ENTER
ESC
RESET
(1) Remote control with two AA batteries
(2) Power cord
(3) Computer cable
(4) Lens cover
(5) User’s manuals (Book x1, CD x1)
(6) Security label
(2)
(3)
(6)
(7)
(7) Soft case
NOTE • Keep the original packing materials for future reshipment. Be sure
to use the original packing materials when moving the projector. Use special
caution for the lens.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparations
Loading batteries into the remote control
Please insert the batteries into the remote control before using it. If the remote
control starts to malfunction, try to replace the batteries. If you will not use the
remote control for long period, remove the batteries from the remote control and
store them in a safe place.
1
2
3
Holding the hook part of the battery
cover, remove it.
1.
2.
Align and insert the two AA batteries
(HITACHI MAXELL, Part No.LR6 or R6P)
according to their plus and minus terminals
as indicated in the remote control.
Replace the battery cover in the direction of the arrow and snap it back into
place.
3.
WARNING ►Always handle the batteries with care and use them only as
directed. Improper use may result in battery explosion, cracking or leakage,
which could result in fire, injury and/or pollution of the surrounding environment.
• Be sure to use only the batteries specified. Do not use batteries of different
types at the same time. Do not mix a new battery with used one.
•
Make sure the plus and minus terminals are correctly aligned when loading a battery.
• Keep a battery away from children and pets.
• Do not recharge, short circuit, solder or disassemble a battery.
•
•
Do not place a battery in a fire or water. Keep batteries in a dark, cool and dry place.
If you observe battery leakage, wipe out the leakage and then replace a battery.
If the leakage adheres to your body or clothes, rinse well with water immediately.
•
Obey the local laws on disposing the battery.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Arrangement
Refer to the illustrations and tables below to determine screen size and projection distance.
The values shown in the table are calculated for a full size screen: 1024 x 768
a
b
Screen size (diagonal)
Projection distance (±10%, from the projector's end)
c1 c2
,
Screen height (±10%)
On a horizontal surface
Suspended from the ceiling
•
Keep a space of 30 cm or more between the sides of the
projector and other objects such as walls. Do not place or
attach anything that would block the lens or vent holes.
• For the case of installation in a special state such
as ceiling mount, the specified mounting accessories
(
16) and service may be required. Before installing
the projector, consult your dealer about your installation.
4 : 3 screen
16 : 9 screen
a
b
b
c1
Screen
height
c2
Screen
height
c1
Screen
height
c2
Screen
height
Screen size
(diagonal)
Projection distance
Projection distance
min. max.
min. max.
type
(inch)
m
m
inch
m
inch cm inch cm inch
m
inch
m
inch cm inch cm inch
30 0.8 0.7 29 0.9 35
40 1.0 1.0 39 1.2 47
50 1.3 1.3 49 1.5 60
60 1.5 1.5 60 1.8 72
70 1.8 1.8 70 2.1 84
39
52
65
78
91
15
21
26
31
36
7
3
3
4
5
6
7
8
9
0.8 33 1.0 39
1.1 44 1.3 53
1.4 55 1.7 66
1.7 66 2.0 80
2.0 77 2.4 93
36
49
61
73
85
14
19
24
29
34
38
1
1
1
2
2
2
3
3
4
4
6
7
9
0
0
1
1
1
1
1
1
1
2
2
3
4
9
11
13
15
17
20
22
26
33
80 2.0 2.0 80 2.5 97 105 41
90 2.3 2.3 90 2.8 109 118 46
100 2.5 2.6 101 3.1 121 131 51
120 3.0 3.1 121 3.7 146 157 62
150 3.8 3.9 152 4.6 183 196 77
2.2 88 2.7 106 97
2.5 100 3.0 120 109 43
2.8 111 3.4 133 122 48
10 3.4 133 4.1 160 146 57
13 4.2 167 5.1 200 182 72
17 5.6 222 6.8 267 243 96
21 7.1 278 8.5 334 304 120
26 8.5 334 10.2 401 365 144
200 5.1 5.2 203 6.2 244 261 103 44
250 6.4 6.5 254 7.8 305 327 129 54
300 7.6 7.8 305 9.3 367 392 154 65
WARNING ►Install the projector in a stable horizontal position.
Place the projector in a cool place, and ensure that there is sufficient ventilation.
►Do not place the projector anyplace where it may get wet.
►
►Do not place the projector where any oils, such as cooking or machine oil, are used.
►
Use only the mounting accessories the manufacturer specified, and leave installing
and removing the projector with the mounting accessories to the service personnel.
► Read and keep the user's manual of the mounting accessories used.
CAUTION ►Avoid placing the projector in smoky, humid or dusty place.
►Position the projector to prevent light from directly hitting the projector’s remote sensor.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting your devices
Be sure to read the manuals for devices before connecting them to the projector.
Make sure that all the devices are suitable to be connected with this product, and
prepare the cables required to connect. Please refer to the following illustrations
to connect them. To input component video signal to COMPUTER IN port, please
see the “Operating Guide” in the CD.
Monitor
PC
RGB IN
AUDIO OUT
RGB OUT
AUDIO OUT
RS-232C
Speakers
(with an
amplifier)
Y
CB/PB CR/PR
L
R
L
R
L
R
VIDEO OUT
HDMI
S-VIDEO OUT
AUDIO OUT
AUDIO OUT
AUDIO OUT
COMPONENT VIDEO OUT
L
R
AUDIO IN
VCR/DVD/Blu-ray Disc player
WARNING ►Do not disassemble or modify the projector and accessories.
►Be careful not to damage the cables, and do not use damaged cables.
CAUTION ►Turn off all devices and unplug their power cords prior to
connecting them to projector. Connecting a live device to the projector may
generate extremely loud noises or other abnormalities that may result in
malfunction or damage to the device and the projector.
►Use appropriate accessory or designated cables. Ask your dealer about non-
accessory cables which may be required a specific length or a ferrite core by
the regulations. For cables with a core only at one end, connect the end with
the core to the projector.
►Make sure that devices are connected to the correct ports. An incorrect
connection may result in malfunction or damage to the device and the projector.
NOTICE ►Use the cables with straight plugs, not L-shaped ones, as the input
ports of the projector are recessed.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting power supply
Put the connector of the power cord into the
AC IN (AC inlet) of the projector.
1.
Firmly plug the power cord’s plug into the
outlet. In a couple of seconds after the
power supply connection, the POWER indicator
2.
will light up in steady orange.
Please remember that when the DIRECT POWER ON
function activated, the connection of the power supply
make the projector turn on.
AC IN
Power cord
WARNING ►Please use extra caution when connecting the power cord, as
incorrect or faulty connections may result in fire and/or electrical shock.
• Only use the power cord that came with the projector. If it is damaged, consult
your dealer to get a new one.
• Only plug the power cord into an outlet whose voltage is matched to the power
cord. The power outlet should be close to the projector and easily accessible.
Remove the power cord for complete separation.
• Never modify the power cord.
This product is also designed for IT power systems with a phase-to-
phase voltage of 220 to 240 V.
NOTICE ►
Turning on the power
Make sure that the power cord is firmly
STANDBY/ON button
POWER indicator
1.
and correctly connected to the projector
and the outlet.
Make sure that the POWER indicator is
steady orange. Then remove the lens cover.
2.
Press the STANDBY/ON button on the
projector or the remote control.
The projection lamp will light up and the
POWER indicator will begin blinking in green.
When the power is completely on, the indicator
will stop blinking and light in steady green.
3.
MY SOURCE/
VIDEO COMPUTER DOC.CAMERA
ASPECT
AUTO SEARCH BLANK
M
A
G
N
I
F
Y
F
R
E
E
Z
E
PAGE
UP
VOLUME
ON
＋
DOWN
OFF
ー
KEYSTONE
MY BUTTON
1
MUTE
2
POSITION
MENU
ENTER
ESC
RESET
WARNING ►A strong light is emitted when the projector’s power is on. Do
not look into the lens of the projector or look inside of the projector through any
of the projector’s openings.
NOTE • Please power on the projector prior to the connected devices.
• The projector has the DIRECT POWER ON function, which can make the
projector automatically turn on. For more information, please see the “Operating
Guide” in the CD.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the projector's elevator
When the place to put the projector is slightly uneven to
the left or right, use the elevator feet to place the projector
horizontally.
12°
Using the feet can also tilt the projector in order to project
at a suitable angle to the screen, elevating the front side of the projector within 12
degrees.
This projector has 2 elevator feet and 2 elevator knobs. An elevator foot is
adjustable while pulling up the elevator knob on the same side as it.
1. Holding the projector, pull the elevator knobs up to loose the elevator feet.
2. Position the front side of the projector to the desired height.
3. Release the elevator knobs in order to lock the elevator feet.
After making sure that the elevator feet are locked, put the projector down
gently.
4.
If necessary, the elevator feet can be manually twisted to make more precise
adjustments. Hold the projector when twisting the feet.
5.
1
5
To loose an elevator foot, pull up the
elevator knob on the same side as it.
To finely adjust, twist the foot.
CAUTION ►Do not handle the elevator buttons without holding the
projector, since the projector may drop down.
►Do not tilt the projector other than elevating its front within 12 degrees using
the adjuster feet. A tilt of the projector exceeding the restriction could cause
malfunction or shortening the lifetime of consumables, or the projector itself.
NOTE • The projector may make a rattling sound when tilted, moved or
shaken, since a flap to control the air flow inside of the projector has moved. Be
aware that this is not a failure or malfunction.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Displaying the picture
Activate your signal source. Turn the signal
1.
MY SOURCE/
VIDEO COMPUTER DOC.CAMERA
source on, and make it send the signal to
the projector.
ASPECT
AUTO SEARCH BLANK
MAGNIFY FREEZE
PAGE
UP
VOLUME
ON
㧗
VOLUME+ button
VOLUME- button
MUTE button
DOWN
OFF
Use the VOLUME + / VOLUME - buttons
to adjust the volume.
To have the projector silent, press the MUTE
KEYSTONE
MY BUTTON
MUTE
MENU
1
2
2.
POSITION
ENTER
button on the remote control.
ESC
RESET
Press the INPUT button on the projector.
3.
Each time you press the button, the
projector switches its input port in turn.
You can also use the remote control to select
an input signal. Press the VIDEO button for
selecting an input signal from the HDMI,
S-VIDEO or VIDEO port, or the COMPUTER
button for selecting an input signal from the
COMPUTER IN port.
INPUT button
Press the ASPECT button on the remote
4.
VIDEO button
MY SOURCE/
VIDEO COMPUTER DOC.CAMERA
control. Each time you press the button,
the projector switches the mode for aspect
ratio in turn.
ASPECT
AUTO SEARCH BLANK
COMPUTER button
ASPECT button
MAGNIFY FREEZE
ON
PAGE
UP
VOLUME
㧗
DOWN
OFF
KEYSTONE
MY BUTTON
MUTE
MENU
1
2
Use the zoom ring to adjust the screen
5.
size.
POSITION
6. Use the focus ring to focus the picture.
ENTER
ESC
RESET
Zoom ring
Focus ring
CAUTION ►If you wish to have a blank screen while the projector's lamp
is on, use the BLANK function. (See the "Operating Guide" in the CD.) Any
other method of blocking the projection light, such as attaching something to
the lens or placing something in front of the lens, may cause the damage to the
projector.
NOTE • The ASPECT button does not work when no proper signal is inputted.
• For the details of how to adjust the picture, please see the “Operating Guide”
in the CD.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Turning off the power
STANDBY/ON button
POWER indicator
Press the STANDBY/ON button on the
1.
projector or the remote control.
The message “Power off?” will appear on
the screen for about 5 seconds.
Press the STANDBY/ON button again
while the message appears.
2.
MY SOURCE/
VIDEO COMPUTER DOC.CAMERA
The projector lamp will go off, and the
POWER indicator will begin blinking in
orange. Then the POWER indicator will
stop blinking and light in steady orange
when the lamp cooling is complete.
ASPECT
AUTO SEARCH BLANK
MAGNIFY FREEZE
ON
PAGE
UP
VOLUME
＋
DOWN
OFF
ー
KEYSTONE
MY BUTTON
1
MUTE
2
POSITION
MENU
ENTER
ESC
RESET
Attach the lens cover, after the POWER
indicator turns in steady orange.
3.
Do not turn the projector on for about 10 minutes or more after turning it off. Also,
do not turn the projector off shortly after turning it on. Such operations might cause
the lamp to malfunction or shorten the lifetime of some parts including the lamp.
WARNING ►Do not touch around the lamp cover and the exhaust vents
during use or just after use, since it is too hot.
►Remove the power cord for complete separation. The power outlet should be
close to the projector and easily accessible.
NOTE • Please power off the projector after any connected devices are
powered off.
• This projector has the AUTO POWER OFF function that can make the
projector turn off automatically. For more information, please see the “Operating
Guide” in the CD.
• When you attach or remove the lens cover, move it vertically up and down
while keeping the knob to the right as illustrated in the figure.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing the lamp
A lamp has finite product life. Using the lamp for long periods of time could cause
the pictures darker or the color tone poor. Note that each lamp has a different
lifetime, and some may burst or burn out soon after you start using them.
Preparation of a new lamp and early replacement are recommended. To prepare
a new lamp, make contact with your dealer and tell the lamp type number.
Type number : 456-8789H
Lamp cover
Turn the projector off, and unplug the power cord.
Allow the projector to cool for at least 45 minutes.
1.
Prepare a new lamp. If the projector is mounted on
2.
a ceiling, or if the lamp has broken, also ask the
dealer to replace the lamp.
In case of replacement by yourself, follow the
following procedure.
3
Loosen the screw (marked by arrow) of the lamp
3.
cover and then slide and lift the lamp cover to the
side to remove it.
Loosen the 2 screws (marked by arrow) of the
lamp, and slowly pick up the lamp by the handle.
Never loosen any other screws.
4.
㧠
㧡
Insert the new lamp, and retighten firmly the
2 screws of the lamp that are loosened in the
previous process to lock it in place.
5.
Handle
While putting the interlocking parts of the lamp
6.
cover and the projector together, slide the lamp
cover back in place. Then firmly fasten the screw of
the lamp cover.
6
Turn the projector on and reset the lamp time
using the LAMP TIME item in the OPTION menu.
7.
(1) Press the MENU button to display a menu.
(2) Point at the ADVANCED MENU in the menu using the
▼/▲ button, then press the ► button.
(3) Point at the OPTION in the left column of the menu using
the ▼/▲button, then press the ► button.
(4) Point at the LAMP TIME using the ▼/▲ button, then
press the ► button. A dialog will appear.
►
(5) Press the button to select “OK” on the dialog. It performs resetting the lamp time.
CAUTION ►Do not touch any inner space of the projector, while the lamp
is taken out.
NOTE • Please reset the lamp time only when you have replaced the lamp,
for a suitable indication about the lamp.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing the lamp (continued)
HIGH VOLTAGE
HIGH TEMPERATURE
HIGH PRESSURE
WARNING ►The projector uses a high-pressure mercury glass lamp. The lamp
can break with a loud bang, or burn out, if jolted or scratched, handled while hot, or
worn over time. Note that each lamp has a different lifetime, and some may burst or
burn out soon after you start using them. In addition, if the bulb bursts, it is possible
for shards of glass to fly into the lamp housing, and for gas containing mercury and
dust containing fine particles of glass to escape from the projector’s vent holes.
►About disposal of a lamp: This product contains a mercury lamp; do not put
it in a trash. Dispose of it in accordance with environmental laws.
• For lamp recycling, go to www.lamprecycle.org (in the US).
• For product disposal, consult your local government agency or www.eiae.org
For more information, ask your dealer.
• If the lamp should break (it will make a loud bang when it does),
unplug the power cord from the outlet, and make sure to request a
replacement lamp from your local dealer. Note that shards of glass
could damage the projector’s internals, or cause injury during handling,
so please do not try to clean the projector or replace the lamp yourself.
Disconnect
•
If the lamp should break (it will make a loud bang when it does), ventilate the
the plug
from the
power
room well, and make sure not to inhale the gas or fine particles that come out
from the projector's vent holes, and not to get them into your eyes or mouth.
• Before replacing the lamp, turn the projector off and unplug the power
cord, then wait at least 45 minutes for the lamp to cool sufficiently.
Handling the lamp while hot can cause burns, as well as damaging the lamp.
outlet
• Never unscrew except the appointed (marked by an arrow) screws.
• Do not open the lamp cover while the projector is suspended from
a ceiling. This is dangerous, since if the lamp’s bulb has broken, the
shards will fall out when the cover is opened. In addition, working in
high places is dangerous, so ask your local dealer to have the lamp
replaced even if the bulb is not broken.
• Do not use the projector with the lamp cover removed. At the lamp
replacing, make sure that the screws are screwed in firmly. Loose
screws could result in damage or injury.
• Use only the lamp of the specified type. Use of a lamp that does not
meet the lamp specifications for this model could cause a fire, damage or
shorten the life of this product.
• If the lamp breaks soon after the first time it is used, it is possible
that there are electrical problems elsewhere besides the lamp. If this
happens, consult your local dealer or a service representative.
•
Handle with care: jolting or scratching could cause the lamp bulb to burst during use.
• Using the lamp for long periods of time, could cause it dark, not to light
up or to burst. When the pictures appear dark, or when the color tone
is poor, please replace the lamp as soon as possible. Do not use old
(used) lamps; this is a cause of breakage.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and replacing the air filter
Please check and clean the air filter periodically. When the indicators or a message
prompts you to clean the air filter, comply with it as soon as possible. The air filter has two
kinds of filters inside. Replace the filters when they are damaged or too soiled. To prepare
the new filters, make contact with your dealer and tell the following type number.
Type number : UX36761 (Filter set)
When you replace the lamp, please replace the air filter. An air
2
filter of specified type will come together with a replacement
lamp for this projector.
Turn the projector off, and unplug the power cord. Allow the
projector to sufficiently cool down.
Use a vacuum cleaner on and around the filter cover.
1.
2.
3.
4.
Filter cover
3
Pick and pull up the filter cover knobs to take it off.
Use a vacuum cleaner for the filter vent of the projector.
Filter cover knobs
Take the fine meshed filter out while holding the filtercover.
4
5.
6.
It is recommended to leave the coarse meshedfilter in the
filter cover as it is.
Use a vacuum cleaner on both sides of the fine meshed
filter while holding it so it will not be sucked in. Use a
vacuum cleaner for the inside of the filter cover to clean
up the coarse meshed filter. If the filters are damaged or
heavily soiled, replace them with new ones.
Put the fine meshed filter on the coarse meshed one,
turning its stitched side up.
Intake vent
7
7.
8.
9.
Put the filter unit back into the projector.
Turn the projector on and reset the filter time using the
FILTER TIME item in the EASY MENU.
Filter (coarse meshed)
Filter (fine meshed)
(1) Press the MENU button to display a menu.
(2) Point at the FILTER TIME using the ▼/▲ button, then
press the ► button. A dialog will appear.
Stitched
side
(3) Press the ► button to select “OK” on the dialog. It
performs resetting the filter time.
WARNING ►Before taking care of the air filter, make sure the power cable
is not plugged in, then allow the projector to cool sufficiently.
►
Use only the air filter of the specified type. Do not use the projector without the
air filter or the filter cover. It could result in a fire or malfunction to the projector
Clean the air filter periodically. If the air filter becomes clogged by dust or the like,
.
►
internal temperatures rise and could cause a fire, a burn or malfunction to the projector.
NOTE • Please reset the filter time only when you have cleaned or replaced
the air filter, for a suitable indication about the air filter.
• The projector may display the message such as “CHECK THE AIR FLOW” or
turn off the projector, to prevent the internal heat level rising.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the CD manual
The other manuals for this product are written into the included CD-ROM titled
“User’s Manual (detailed)”. Before using the CD-ROM, please read the following
to ensure the proper use.
System requirements
The system for using the CD-ROM requires the following.
Windows®:
OS:Microsoft® Windows® 98, Windows® 98SE,
Windows NT®4.0, Windows® Me,
Windows® 2000/Windows® XP or later
CPU:Pentium® processor 133MHz / Memory:32MB or more
OS:Mac OS® 10.2 or later
Macintosh®:
CPU:PowerPC® / Memory:32MB or more
CD-ROM drive: 4x CD-ROM drive
Display:
Applications:
256 color / 640x480 dots resolution
Microsoft® Internet Explorer®4.0 and
Adobe® Acrobat® Reader® 4.0 or later
How to use the CD
1. Insert CD into PC’s CD-ROM drive.
Windows®:
In a while, Web browser automatically starts. Start up
window comes up.
(1) Double-click on the “Projectors” icon appeared on the
desktop screen.
Macintosh®:
(2) When “main.html” file is clicked, Web browser will start
and Initial window will appear.
2. Click the model name of your projector first, and then click language you want
from the displayed list. The User’s manual (detailed) will open.
CAUTION ►Only use the CD-ROM in a computer CD drive. The CD-
ROM is designed for PC use only. NEVER INSERT THE CD-ROM INTO A
NON-COMPUTER CD PLAYER! Inserting the CD-ROM into an incompatible
CD drive may produce a loud noise, which in turn MAY RESULT IN EAR AND
SPEAKER DAMAGE!
• After using CD-ROM, please put it into CD case and keep it. Please keep
the CD neither in direct sunlight nor in a high temperature and high humidity
environment.
NOTE • The information in the CD-ROM is subject to change without notice.
• No responsibility is taken for any obstacle and defect to hardware and
software of your PC as a result of the use of the CD-ROM.
• All or Any part of the information in the CD-ROM must not be copied,
reproduced or republished without notice to our company.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Item
Specification
Product name
Liquid Crystal Panel
Lamp
Liquid crystal projector
786,432 pixels (1024 horizontal x 768 vertical)
200 W UHB
Speaker
1 W
Power supply
Power consumption
Temperature range
AC 100-120 V/2.9 A, AC 220-240 V/1.4 A
AC 100-120 V/290 W, AC 220-240 V/270 W
5 ~ 35 °C (Operating)
306 (W) x 77 (H) x 221 (D) mm
* Not including protruding parts. Please refer to the following figure.
Size
Weight (mass)
approx. 2.2 kg
Computer input port
Video input port
COMPUTER IN
S-VIDEO ..............mini DIN 4 pin x1
....................... D-sub 15 pin mini x1 VIDEO.................................RCA x1
Computer output port
Audio input/output port
Ports
MONITOR OUT
AUDIO IN1 ............... Stereo mini x1
....................... D-sub 15 pin mini x1 AUDIO IN2 ............... Stereo mini x1
HDMI input port AUDIO OUT ............. Stereo mini x1
HDMI ............... HDMI connector x1 Others
CONTROL................D-sub 9 pin x1
Lamp: 456-8789H
Filter set: UX36761
Laser remote control: RC-R008
Optional parts
* For more information, please consult your dealer.
306
[unit: mm]
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting - Warranty and after-service
If an abnormal operation (such as smoke, strange odor or excessive sound)
should occur, stop using the projector immediately. Otherwise if a problem occurs
with the projector, first refer to the “Troubleshooting” of the “Operating Guide” in
the CD and run through the suggested checks.
If this does not resolve the problem, please consult your dealer or service
company. They will tell you what warranty condition is applied.
Please check the following web address where you may find the latest information
for this projector.
NOTE • The information in this manual is subject to change without notice.
• The manufacturer assumes no responsibility for any errors that may appear in
this manual.
• The reproduction, transfer or copy of all or any part of this document is not
permitted without express written consent.
Trademark acknowledgment
• Mac®, Macintosh® and Mac OS® are registered trademarks of Apple Inc.
• Pentium® is a registered trademark of Intel Corp.
• Adobe® and Acrobat®, Reader® are registered trademarks of Adobe Systems
Incorporated.
• Microsoft®, Internet explorer®, Windows®, Windows NT® and Windows Vista®
are registered trademarks of Microsoft Corporation in the U.S. and/or other
countries.
• PowerPC® is a registered trademark of International Business Machines
Corporation.
• HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks
or registered trademarks of HDMI Licensing LLC in the United States and other
countries.
• Blu-ray DiscTM and Blu-rayTM are trademarks of Blu-ray Disc Association.
All other trademarks are the properties of their respective owners.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
DUKANE CORP AV SERVICE DEPT
2900 Dukane Drive
St Charles, IL 60174
800-676-2487 / 630-762-4032
Fax 630-584-5156
403-8789H-GENERAL-00
Download from Www.Somanuals.com. All Manuals Search And Download.
|