Liquid Crystal Projector
Model 8768
USER'S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Information
RF Interference
WARNING
The Federal Communications Commission does not allow any modifications or changes to the unit EXCEPT those
specified by Soluctions (America), Inc. in this manual. Failure to comply with this government regulation could
void your right to operate this equipment.This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses, and can radi-
ate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio / TV technician for help.
In UK, a BS approved power cable with moulded plug has a Black (five Amps) fuse installed for use with this equip-
ment. If a power cable is not supplied with this equipment please contact your supplier.
Important Safeguards
These safety instructions are to ensure the long life of your projector and to prevent fire and shock. Please read them
carefully and heed all warnings.
Installation
1. For best results, use your projector in a darkened room.
2. Place the projector on a flat, level surface in a dry area away from dust and moisture.
3. Do not place your projector in direct sunlight, near heaters or heat radiating appliances.
4. Exposure to direct sunlight, smoke or steam can harm internal components.
5. Handle your projector carefully. Dropping or jarring can damage internal components.
6. Do not place heavy objects on top of the projector.
7. If you wish to have the projector installed on the ceiling:
a. Do not attempt to install the projector yourself.
b. The projector must be installed by qualified technicians in order to ensure proper operation and reduce the
risk of bodily injury.
c. In addition, the ceiling must be strong enough to support the projector and the installation must be in accor-
dance with any local building codes.
d. Please consult your dealer for more information.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Information
Fire and Shock Precautions
1. Ensure that there is sufficient ventilation and that vents are unobstructed to prevent the build-up of heat inside
your projector. Allow at least 4 inches (10 cm) of space between your projector and a wall.
2. Prevent foreign objects such as paper clips and bits of paper from falling into your projector.
Do not attempt to retrieve any objects that might fall into your projector.
Do not insert any metal objects such as a wire or screwdriver into your projector. If something should fall into
your projector, disconnect it immediately and have the object removed by a qualified service personnel.
3. Do not place any liquids on top of your projector.
4. Do not look into the lens while the projector is on. Serious damage to your eyes could result.
5. Keep any items such as magnifying glass out of the light path of the projector. The light being projected from the
lens is extensive, therefore any kind of abnormal objects that can redirect light coming out of the lens, can
cause unpredictable outcome such as fire or injury to the eyes.
6. Do not cover the lens with the supplied lens cap or equivalent while the projector is on. Doing so can lead to
melting of the cap and possibly burning your hands due to the heat emitted from the light output.
7. The projector is designed to operate on a power supply of 100--240 V 50/60 Hz AC. Ensure that your power
supply fits this requirement before attempting to use your projector.
8. Handle the power cable carefully and avoid excessive bending.
A damaged cord can cause electric shock or fire.
9. If the projector is not to be used for an extended period of time, disconnect the plug from the power outlet.
10. Do not touch the power plug during a thunderstorm. Doing so can cause electrical shock or fire.
CAUTION
• Do not try to touch the ventilation outlet on the left side (when seen from the front) as it can become heated
while the projector is turned on.
• Do not use the tilt-foot for purposes other than originally intended.
Misuses such as gripping the tilt-foot or hanging on the wall can cause damage to the projector.
• Do not send the soft carrying case by parcel delivery service or cargo shipment. The projector inside the soft
carrying case could be damaged. (However, it is possible to use it as a carriercase on board.)
• Enable High-Speed Fan mode if you continue to use the projector for consecutive days. (From the menu,
select [Setup] → [Page 4] → [Fan Mode].)
• Do not unplug the power cable from the wall outlet under any one of the following circumstances.
Doing so can cause damage to the projector:
*
*
While the Hour Glass icon appears.
While the cooling fans are running. (The cooling fans continue to work for 10 seconds after the projector is
turned off).
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Information
Lamp Replacement
•
•
To replace the lamp, follow all instructions provided on page 107.
Be sure to replace the lamp when the message “The lamp has reached the end of its usable life.
Please replace the lamp.” appears. If you continue to use the lamp after the lamp has reached the end of
its usable life, the lamp bulb may shatter, and pieces of glass may be scattered in the lamp case. Do not touch
them as the pieces of glass may cause injury.
If this happens, contact your dealer for lamp replacement.
•
Allow a minimum of 10 seconds to elapse after turning off the projector.
Then turn off the main power switch, disconnect the power cable and allow 60 minutes to cool the projector
before replacing the lamp.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Important Information........................................................................2
1. Introduction ......................................................................................8
ᕡ What's in the Box? ........................................................................................................ 9
ᕢ Introduction to the Projector ....................................................................................... 10
ᕣ Part Names of the Projector ....................................................................................... 12
Carrying the Projector ........................................................................................... 13
Top Features ......................................................................................................... 14
Terminal Panel Features ....................................................................................... 15
ᕤ Remote Control Features ........................................................................................... 17
2. Installation and Connections.................................................... 20
ᕡ Setting Up the Screen and the Projector .................................................................... 21
Selecting a Location.............................................................................................. 21
Throw Distance and Screen Size.......................................................................... 22
ᕢ Making Connections ................................................................................................... 23
Enabling the computer’s external display.............................................................. 23
Connecting Your PC or Macintosh Computer........................................................ 23
To connect SCART output (RGB) ......................................................................... 24
Connecting an External Monitor ........................................................................... 25
Connecting Your DVD Player with Component Output .......................................... 26
Connecting Your VCR or Laser Disc Player .......................................................... 27
Connecting the Supplied Power Cable ................................................................. 28
3. Projecting an Image (Basic Operation) ................................. 29
ᕡ Turning on the Projector ............................................................................................. 30
ᕢ Selecting a Source ..................................................................................................... 32
ᕣ Adjusting the Picture Size and Position ...................................................................... 33
ᕤ Correcting Keystone Distortion ................................................................................... 35
ᕥ Optimizing RGB Picture Automatically ....................................................................... 37
ᕦ Turning Up or Down Volume ....................................................................................... 37
ᕧ Turning off the Projector ............................................................................................. 38
ᕨ After Use..................................................................................................................... 38
4. Convenient Features.................................................................... 39
ᕡ Switching Operation Mode between Computer and Projector.................................... 40
ᕢ Turning Off the Image and Sound............................................................................... 40
ᕣ Freezing a Picture....................................................................................................... 40
ᕤ Using the Pointer ........................................................................................................ 41
ᕥ Enlarging and Moving a Picture.................................................................................. 41
ᕦ Getting the On-line Help ............................................................................................. 42
ᕧ Using a USB Mouse ................................................................................................... 42
ᕨ Using the Remote Mouse Function ............................................................................ 43
ᕩ Correcting Horizontal and Vertical Keystone Distortion (Cornerstone)....................... 44
µ Making Freehand Drawings on a Projected Image (ChalkBoard) .............................. 47
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
¸
Storing Images Displayed on the Projector on the PC card or USB Memory (Capture) .......... 48
¹ Preventing the Unauthorized Use of the Projector ..................................................... 49
Ƹ Using a USB Memory Device or USB Memory Card Reader..................................... 54
5. Using the Viewer........................................................................... 55
ᕡ Making the Most out of the Viewer Function............................................................... 56
ᕢ Operating the Viewer Function from the Projector...................................................... 58
» Changing Background Logo ....................................................................................... 64
6. Using Dynamic Image Utility 2.0 on the supplied CD-ROM ................... 65
ᕡ End User License Agreement.................................................................................... 66
ᕢ Introduction................................................................................................................ 67
ᕣ Operating Environment.............................................................................................. 68
ᕤ Equipment Connections and Settings ....................................................................... 69
ᕥ Software Installation .................................................................................................. 69
ᕦ Starting/Exiting the Software ..................................................................................... 70
ᕧ Troubleshooting ......................................................................................................... 72
7. Using On-Screen Menu................................................................ 73
ᕡ Using the Menus......................................................................................................... 74
ᕢ Menu tree ................................................................................................................... 75
ᕣ Menu Elements........................................................................................................... 77
ᕤ Menu Descriptions & Functions [Adjust]..................................................................... 78
ᕥ Menu Descriptions & Functions [Image]..................................................................... 82
ᕦ Menu Descriptions & Functions [Setup] ..................................................................... 85
ᕧ Menu Descriptions & Functions [Information] ........................................................... 100
ᕨ Menu Descriptions & Functions [Reset] ................................................................... 101
ᕩ Entry List .................................................................................................................. 102
8. Maintenance ................................................................................. 104
ᕡ Cleaning the Filters.................................................................................................. 105
ᕢ Cleaning the Cabinet ............................................................................................... 105
ᕣ Cleaning the Lens.................................................................................................... 106
ᕤ Replacing the Lamp and Filters............................................................................... 107
9. Appendix ........................................................................................ 110
ᕡ Troubleshooting ....................................................................................................... 111
ᕢ Specifications .......................................................................................................... 114
ᕣ Cabinet Dimensions ................................................................................................ 116
ᕤ Pin Assignments of D-Sub COMPUTER 1/2 Input Connector ................................ 117
ᕥ Compatible Input Signal List .................................................................................... 118
ᕦ PC Control Codes and Cable Connection ............................................................... 119
ᕧ Using Software Keyboard ........................................................................................ 120
7
Download from Www.Somanuals.com. All Manuals Search And Download.
1
Introduction
ᕡ What's in the Box? ....................................................... 9
ᕢ Introduction to the Projector ...................................... 10
ᕣ Part Names of the Projector ...................................... 12
Carrying the Projector .......................................................................................... 13
Top Features......................................................................................................... 14
Terminal Panel Features....................................................................................... 15
ᕤ Remote Control Features .......................................... 17
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Introduction
ᕡ What's in the Box?
Make sure your box contains everything listed. If any pieces are missing, contact your dealer.
Please save the original box and packing materials if you ever need to ship your VT770 Projector.
P
C
R E T N E
C
A
Lens cap
R
D
C
A
N
C
S
E
E
L
E
L
C
T
3
D
R
M
E
E
F
O
N
U
R
M
O
S
N
O
U
R
S
/
T
A
C
E
N
D
B
Y
A
U
T
O
P
O
A
D
W
S
J
E
T
U
S
R
A
L
T
A
T
U
M
S
P
Z O O M
O
F
F
F
O
C
U
S
V
ID
E
O
S-
P
O
VID
W
E
E
R
O
COMPUTER
1
2
O
N
AUTO ADJ.
COMPONENT
S
E
L
EC
T
P
J
3D-R
EF
O
R
M
ASPECT
SOURCE
POINTER
V
O
L
U
M
E
VIEWER
MAGNIFY
SLIDE
PICTURE
PIC-MUTE
FREEZ
HELP
Remote control
Batteries (AA ꢀ 2)
Projector
Power cable
USB cable
RGB signal cable
Soft carrying case
User's Manual
9
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Introduction
ᕢ Introduction to the Projector
This section introduces you to the 8768 Projector and describes key features and controls.
Congratulations on Your Purchase of the VT770 Projector
The 8768 is a sophisticated three panel LCD XGA projector that produces an enhanced display in less than an 8-
pound (4kg) design. With the 8768 you will be able to project images up to 300” (measured diagonally). Enjoy crisp
and sharp large screen display from your DVD player, VCR, satellite hookup, HDTV source, PC, Workstation or
Macintosh computer (desktop or notebook) and images from your digital camera PC Card, compact flash memory or
USB storage device. The 8768 provides for enhanced security options to help deter projector theft and provides for
full projector control through RS232 support. With input and output flexibility, long lamp life and a full function remote,
the 8768 lets you enjoy larger than life viewing from a compact and easy to setup and use projector.
Features you’ll enjoy on the VT770:
•
•
Automatic vertical keystone correction for fast and easy application setup
Built-in Wall Color Correction presets provide for adaptive color correction when projecting onto non-white
screen material.
•
3D Reform™ enhanced image technology for increased projector versatility that provides for horizontal, vertical
and diagonal keystone correction (allows for positioning the projector in off center locations in the room and still
get aligned images)
•
•
USB memory or PC card interfaces provide for computerless presentations
Enhanced smart security settings for password protection, control panel lock, menu lock and PC card protection
key to help prevent unauthorized access, adjustments and theft deterrence
•
•
•
•
UXGA compatible, XGA native resolution
Variable audio out control of external amplified speakers via the projector
Extensive user adjustable picture and color management settings
Core technologies – Advanced Image Processing for highest
quality of display and ease of use
•
•
•
Display 16:9 or 4:3 aspect ratio information and fill the screen
HDTV (1080i, 720p) and SDTV (480p, 480i) compatibility
Digital photo viewer to display larger than life images from your digital cameras PC card, compact flash card or
USB storage device
•
•
•
Easy set up, use and operation
Manual zoom and manual focus lens
Whisper Mode lamp technology for increased lamp life, reduced energy consumption and overall total cost of
ownership savings
•
•
Wireless remote control operation
External control via RS232
10
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Introduction
•
•
8768 has exclusive intelligent pixel blending technology which provides for extremely accurate
image compression and HDTV (1920x1080 and 1280x720) display resolution*.
Supports most IBM VGA, SVGA, XGA, Macintosh, component signal (YCbCr/YPbPr) or other RGB signals
within a horizontal frequency range of 15 to 100 kHz and a vertical frequency range of 50 to 120 Hz. This
includes NTSC, NTSC4.43, PAL, PAL-M, PAL-N, PAL60 and SECAM standard video signals
NOTE: Composite video standards are as follows:
NTSC: U.S. TV standard for video in U.S. and Canada.
PAL: TV standard used in Western Europe.
PAL-N: TV standard used in Argentine, Paraguay and Uruguay.
PAL-M: TV standard used in Brazil.
PAL60: TV standard used for NTSC playback on PAL TVs.
SECAM: TV standard used in France and Eastern Europe.
NTSC4.43: TV standard used in Middle East countries.
*1 Do not attempt to mount the projector on the ceiling yourself. To ensure proper operation and reduce the risk
of bodily injury a qualified technician must install the projector. In addition, the ceiling must be strong enough
to support the projector and the installation must be in accordance with any local building codes. Please
consult your dealer for more information.
*2 HDTV 1080i (1920 ꢀ 1080) and HDTV 720 p (1280 ꢀ 720) are displayed.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Introduction
ᕣ Part Names of the Projector
Controls
(See page 14)
Lamp Cover
(See page 107)
Zoom lever
E T N E
R
P C C A R
D
C
A
N
C
S E L E C T
E
L
(See page 34)
3 D R E F O R M
M
E
N
U
O
S O U R C E
N
S
/
T
A
N
D
B
Y
A U
T
O
P O W E R
S T A T U S
L A M P
A
D
J U
S
T
Z
O
O
M
F
O
C
U
S
Focus ring
(See page 34)
Lamp Cover Screw
Lens
Ventilation (outlet)
Heated air exhausted from
here.
Lens cap
Carrying Handle
Remote sensor
(See page 97)
Adjustable Tilt Foot
(See page 33)
Adjustable Tilt Foot Button
(See page 33)
Built-in Security Slot ( )*
Stereo Speaker
S
U
C
O
F
ZOOM
r
r
T
LAMP
STATUS
POWER
S
U
J
b
D
A
C
O
T
T
Y
U
N
A
E
I
O
Y
N
R
R
B
O
O
P
D
M
O
N
A
C
T
/S
N
N
O
SOURCE
O
/M
L
U
N
IO
E
D
U
A
M
3D REFORM
O
O
E
I
D
N
T
IO
O
C
D
V
-
/
M
E
U
S
L
A
L
E
E
S
C
O
E
I
D
N
OUSE)
A
C
V
1
2
USB(M
R
E
T
U
P
Remote sensor
(See page 97)
M
O
C
R
E
E
N
T
PC CARD
IO
D
U
A
USB(CO
IO
D
D
R
U
A
A
C
C
P
R
E
T
U
P
T
U
M
O
O
R
C
O
IT
N
O
M
L
O
R
T
N
O
C
C
P
IN
C
A
Ventilation (inlet) / Filter Cover
AC Input
Terminal Panel
(See page 15)
Main Power Switch
Connect the supplied power cable's
two-pin plug here, and plug the
other end into an active wall outlet.
(See page 28)
When you plug the supplied power
cable into an active wall outlet and
turn on the Main Power switch, the
POWER indicator turns orange and
the projector is in standby mode.
(See page 30)
*
This security slot supports the MicroSaver ® Security System. MicroSaver ® is a registered trademark of
Kensington Microware Inc. The logo is trademarked and owned by Kensington Microware Inc.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Introduction
Carrying the Projector
Always carry your projector by the handle.
Ensure that the power cable and any other cables con-
necting to video sources are disconnected before mov-
ing the projector.
F
O
C
U
S
Z O O M
When moving the projector or when it is not in use, cover
the lens with the lens cap.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Introduction
Top Features
9
8
5
6 4
SELECT
SOURCE
AUTO ADJUST
LAMP
STATUS
POWER
3
3D REFORM
ON/STAND BY
PC CARD
10 12 11
7
1 2
6. AUTO ADJ. Button
1. POWER Button (ON / STAND BY) (
)
Use this button to adjust Position-H/V and Pixel Clock/
Phase for an optimal picture (See page 37). Available
for the RGB signal only.
Use this button to turn the power on and off when the
main power is supplied.
To turn on or off the projector, press and hold this but-
ton for a minimum of two seconds.
7. 3D REFORM Button
Press this button to enter 3D Reform mode to correct
the keystone (trapezoidal) distortion, and make the
image square. See pages 35 and 44.
2. POWER Indicator
When this indicator is green, the projector is on;when
this indicator is orange, it is in standby mode. See the
Power Indicator section on page 111 for more details.
8. MENU Button
Displays the menu.
3. STATUS Indicator
If this light blinks red rapidly, it indicates that an error
has occurred, the lamp cover is not attached properly
or the projector has overheated.
If this light remains orange, it indicates that you have
pressed a cabinet button while the Cabinet Button is
locked. See the Status Indicator section on page 111
for more details.
9. SELECT ̆̄̇̈ / Volume Buttons
̆̄ : Use these buttons to select the menu of the
item you wish to adjust.
̇̈ : Use these buttons to change the level of a se-
lected menu item.
A press of the ̈ button executes the selec-
tion. When no menus appear, these buttons
work as a volume control.
4. LAMP Indicator
When an image is magnified, the SELECT ̆̄̇̈
button moves the image.
If this light blinks red rapidly, it's warning you that the
lamp has reached the end of its usable life. After this
light appears, replace the lamp as soon as possible
(See page 107). If this is lit green continually, it indi-
cates that the lamp mode is set to Eco. See the Lamp
Indicator section on page 111 for more details.
10. ENTER Button
Executes your menu selection and activates items
selected from the menu.
11. CANCEL Button
5. SOURCE Button
Pressing this button will return to the previous menu.
While you are in the main menu, pressing this button
will close the menu.
Use this button to select a video source such as a PC,
VCR, DVD player or Viewer (PC card).
Press and release this button quickly to display the
Source List.
12. PC CARD Access Indicator
Each time this button is pressed for a minimum of ONE
second, the input source will change as follows:
Computer1 → Computer2 → Component → Video →
S-Video → Viewer → Entry List → Computer1 → ...
If no input signal is present, the input will be skipped.
Lights while accessing a PC card.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Introduction
Terminal Panel Features
3
1
4
COMPONENT
PC CARD
USB(MOUSE)
AUDIO
Y
Cb/Pb
Cr/Pr
USB(COMPUTER)
AUDIO
L/MONO
MONITOR OUT
PC CONTROL
COMPUTER 1
AUDIO
S-VIDEO
R
R
AUDIO
L/MONO
VIDEO
COMPUTER 2
AUDIO
2
5
1. COMPUTER 1 Input Connector (Mini D-Sub 15 Pin)
AUDIO OUT Mini Jack (Stereo Mini)
Connect your computer or other analog RGB equip-
ment such as IBM compatible or Macintosh comput-
ers. Use the supplied RGB cable to connect to your
computer.
You can use this jack to output sound from the cur-
rently selected source (COMPUTER 1/2, COMPO-
NENT, VIDEO or S-VIDEO). The current or last dis-
played source's audio will be sent to the audio output
even in Idle mode.
COMPUTER 1 AUDIO Input Mini Jack (Stereo Mini)
Output sound level (volume, bass/treble and mute)
can be adjusted in accordance with the sound level
of the internal speaker.
This is where you connect the audio output from your
computer when connected to the COMPUTER 1 in-
put. A commercially available audio cable is required.
Output sound level (volume, bass/treble and mute)
cannot be adjusted in Idle mode.
2. COMPUTER 2 Input Connector (Mini D-Sub 15 Pin)
Note that this cannot be used as a headphone jack.
Connect your computer or other analog RGB equip-
ment such as IBM compatible or Macintosh comput-
ers. Use the supplied RGB cable to connect to your
computer.
(When audio equipment is connected, the projector
speaker is disabled.)
This connector also supports SCART output signal.
The SCART cable is sold separately.
See page 24 for more details.
4. COMPONENT (Y, Cb/Pb, Cr/Pr) Input Connectors
(RCA)
Connect component video outputs (Y/Cb/Cr,Y/Pb/Pr)
of the external equipment such as DVD player.
NOTE: The COMPUTER 2 Input does not support Plug &
Play.
NOTE: The “Y” connector accepts Video signal.
COMPONENT AUDIO Input Jacks R/L (RCA)
COMPUTER 2 AUDIO Input Mini Jack (Stereo Mini)
These are your left and right channel audio inputs for
stereo sound from your DVD player or component
equipment connected to COMPONENT Input Connec-
tors.
This is where you connect the audio output from your
computer when connected to the COMPUTER 2 in-
put. A commercially available audio cable is required.
3. MONITOR OUT Connector (Mini D-Sub 15 Pin)
5. VIDEO Input Connector (RCA)
You can use this connector to loop your computer
image to an external monitor from the COMPUTER
1/2 or component video input source.
Connect aVCR, DVD player, laser disc player, or docu-
ment camera here to project video.
VIDEO/S-VIDEO AUDIO Input Jacks R/L (RCA)
This connector also outputs a COMPUTER signal
or component signal in Idle mode.
These are your left and right channel audio inputs for
stereo sound from a Video or S-Video source.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Introduction
Terminal Panel Features
10
11
8 7
COMPONENT
PC CARD
USB(MOUSE)
Y
Cb/Pb
Cr/Pr
USB(COMPUTER)
AUDIO
L/MONO
MONITOR OUT
AUDIO
COMPUTER 1
COMPUTER 2
AUDIO
S-VIDEO
R
R
AUDIO
L/MONO
VIDEO
PC CONTROL
AUDIO
9
6
6. S-VIDEO Input Connector (Mini DIN 4 Pin)
9. PC CONTROL Port (D-Sub 9 Pin)
Here is where you connect the S-Video input from an
external source like a VCR.
Use this port to connect your PC to control your pro-
jector via a serial cable.This enables you to use your
PC and serial communication protocol to control the
projector. A commercially available RS232C cross
cable is required to use this port.You can also control
the projector by using Dynamic Image Utility 2.0 in-
cluded on the supplied CD-ROM.
NOTE: S-Video provides more vivid color and higher
resolution than the traditional composite video format.
7. USB (MOUSE) Port (Type A)
Connect a commercially available USB mouse. You
can operate the menu or Viewer with the USB mouse
via this port.
To do so you must first have Dynamic Image Utility
2.0 installed on your PC. If you are writing your own
program, typical PC control codes are on page 119.
8. USB (COMPUTER) Port (Type B)
10. PC CARD Slot
Connect this port to the USB port (type A) of your PC
using the supplied USB cable. You can operate your
computer's mouse functions from the remote control.
Insert a PC card here.
11. PC CARD Eject Button
Press to partially eject a PC card partially.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Introduction
ᕤ Part Names of the Remote Control
5. VIDEO Button
1
2
Press this button to select a video source from aVCR,
DVD player, laser disc player or document camera.
OFF
ON
POWER
4
5
3
9
AUTO ADJ.
COMPONENT
VIDEO
S-VIDEO
6. S-VIDEO Button
COMPUTER
1
2
Press this button to select an S-Video source from a
VCR.
6
7
11
10
8
7. COMPUTER 1 Button
Press this button to select COMPUTER 1 input.
SELECT
12
14
8. COMPUTER 2 Button
Press this button to select COMPUTER 2 input.
13
9. AUTO ADJ. Button
PJ
Use this button to adjust an RGB source for an opti-
mal picture. See page 37.
3D REFORM
SOURCE
10. COMPONENT Button
ASPECT POINTER VIEWER
Press this button to select a video source from com-
ponent equipment connected to your COMPONENT
input.
SLIDE
VOLUME MAGNIFY
PICTURE
PIC-MUTE
FREEZE
HELP
11. MENU Button
Displays the menu for various settings and adjust-
ments.
12. SELECT ̆̄̇̈ (Mouse) Button
When you are in the Computer mode, these buttons
work as a computer mouse.
When you are in the Projector mode, which is indi-
cated by lighting the PJ button. See page 40.
NOTE: If you are using a Macintosh computer, you can click
either the CANCEL (right-click) or ENTER (left-click) button to
activate the mouse.
̆̄ : Use these buttons to select the menu of the
item you wish to adjust.
1. Infrared Transmitter
Direct the remote control toward the remote sensor
on the projector cabinet.
̇̈ : Use these buttons to change the level of a se-
lected menu item. A press of the ̈ button ex-
ecutes the selection.When no menus appear,
these buttons work as a volume control.
When an image is magnified, the SELECT ̆̄̇̈
button moves the image.
2. LED
Flashes when any button is pressed.
3. POWER ON Button
When the main power is on, you can use this button
to turn your projector on.
13. ENTER (Left Click) Button
When you are in the Computer mode, this button works
as the mouse left button.When this button is pressed
and held for a minimum of 2 seconds, the drag mode
is set. When you are in the Projector mode, which is
indicated by lighting the PJ button: Use this button to
enter your menu selection. It works the same way as
the ENTER button on the cabinet. See page 40.
NOTE: To turn on the projector, press and hold the POWER ON
button for a minimum of two seconds.
4. POWER OFF Button
You can use this button to turn your projector off.
NOTE: To turn off the projector, press and hold the POWER
OFF button for a minimum of two seconds.
14. CANCEL (Right Click) Button
When you are in the Computer mode, this button works
as the mouse right button. When you are in the Pro-
jector mode, which is indicated by lighting the PJ but-
ton: It works the same way as the CANCEL button on
the cabinet. See page 40.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Introduction
18. ASPECT Button
OFF
ON
Press this button to display the Aspect Ratio select
screen. See page 82.
POWER
AUTO ADJ.
COMPONENT
VIDEO
S-VIDEO
COMPUTER
1
2
19. POINTER Button
Press this button to display one of the nine pointers;
press again to hide the pointer. You can move your
pointer icon to the area you want on the screen using
the SELECT ̆̄̇̈ button. See page 41.
SELECT
20. VOLUME (+)(–) Button
Press (+) to increase the volume and (–) to decrease
it.
PJ
15
NOTE: The default is the Computer mode, which allows you to
use the SELECT, CANCEL, and ENTER buttons as your computer
mouse. When the POWER ON/OFF, MENU, 3D REFORM, AS-
PECT, POINTER, HELP, MAGNIFY, VIEWER or PICTURE button
is pressed, the PJ button lights red to indicate that you are in the
Projector mode. If no buttons are pressed within 60 seconds,
the light goes out and the Projector mode is canceled.
3D REFORM
SOURCE
16
17
24
ASPECT POINTER VIEWER
18
19
20
SLIDE
VOLUME MAGNIFY
25
21
26
27
PICTURE
PIC-MUTE
FREEZE
HELP
22
23
21. MAGNIFY (+)(–) Button
Use this button to adjust the image size up to 400%.
The image is magnified about the center of the screen.
See page 41.
22. PICTURE Button
15. PJ Button
Press this button to display the Picture window. Each
time this button is pressed, the option will be changed.
See page 78.
Press this button to switch the SELECT, CANCEL, and
ENTER buttons between the Projector mode (lit red)
and the Computer mode.
Press this button or any one of the POWER ON/OFF,
MENU, 3D REFORM, ASPECT, POINTER, HELP,
MAGNIFY, VIEWER or PICTURE buttons to switch to
the Projector mode and the PJ button lights red. To
switch back to the Computer mode, press the PJ but-
ton again. See page 40.
23. PIC-MUTE Button
This button turns off the image and sound for a short
period of time.
Press again to restore the image and sound.
24. VIEWER Button
Press this button to select the Viewer source.
16. 3D REFORM Button
Press this button to enter 3D Reform to correct the
keystone (trapezoidal) distortion, and make the im-
age square. See pages 35 and 44.
25. SLIDE (+)(–) Button
Press (+) to select the next folder or slide and (–) to
select the previous folder or slide. See page 58.
17. SOURCE Button
26. FREEZE Button
Use this button to select a video source such as a PC,
VCR, DVD player or Viewer (PC card).
Press and release this button quickly to display the
Source List.
Each time this button is pressed for a minimum of ONE
second, the input source will change as follows:
This button will freeze a picture. Press again to re-
sume motion.
27. HELP Button
Provides suitable HELP information.
Computer1 → Computer2 → Component → Video →
S-Video → Viewer → Entry List → Computer1 → ...
If no input signal is present, the input will be skipped.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Introduction
Battery Installation
1 Remove the battery cover.
2 Remove both old batteries and in-
3 Slip the cover back over the bat-
teries until it snaps into place. Do
not mix different types of batter-
ies or new and old batteries.
stall new ones (AA). Ensure that
you have the batteries' polarity (+/
-) aligned correctly.
Note on Remote Control Operation
If you press and hold the SELECT ̆̄̇̈ button while installing new batteries, the remote control may fail to work
properly.
Should this happen, remove the batteries and then install them again without touching the SELECT button.
Remote Control Precautions
•
•
•
•
•
•
Handle the remote control carefully.
If the remote control gets wet, wipe it dry immediately.
Avoid excessive heat and humidity.
If you will not be using the remote control for a long time, remove the batteries.
Do not place the batteries upside down.
Do not use new and old batteries together, or use different types of batteries together.
Operating Range for Wireless Remote Control
Remote sensor on projector cabinet
7m/22 feet
7m/22 feet
30°
30°
Remote control
30°
30°
•
•
The infrared signal operates by line-of-sight up to a distance of about 22 feet/7 m and within a 60-degree angle of
the remote sensor on the projector cabinet.
The projector will not respond if there are objects between the remote control and the sensor, or if strong light falls
on the sensor.
Weak batteries will also prevent the remote control from properly operating the projector.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Installation and Connections
ᕡ Setting Up the Screen and the Projector ................... 21
Selecting a Location ............................................................................................. 21
Throw Distance and Screen Size ......................................................................... 22
ᕢ Making Connections .................................................. 23
Enabling the computer’s external display ............................................................. 23
Connecting Your PC or Macintosh Computer ....................................................... 23
To connect SCART output (RGB) ......................................................................... 24
Connecting an External Monitor ........................................................................... 25
Connecting Your DVD Player with Component Output ......................................... 26
Connecting Your VCR or Laser Disc Player .......................................................... 27
Connecting the Supplied Power Cable ................................................................. 28
20
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Installation and Connections
This section describes how to set up your projector and how to connect PCs, video and audio sources.
Your projector is simple to set up and use.
But before you get started, you must first:
1
z
x
Set up a screen and the projector.
Connect your computer or video equip-
ment to the projector. See pages 23 -
27.
T
JUS
AD
TO
AU
D
B
Y
AN
/ST
ON
U
M
E
N
E
NC
E
N
T
E
R
I
C
c
Connect the supplied power cable. See
page 28.
3
2
NOTE: Ensure that the power cable and any
other cables are disconnected before moving
the projector. When moving the projector or
when it is not in use, cover the lens with the
lens cap.
To the wall outlet.
ᕡ Setting Up the Screen and the Projector
Selecting a Location
The further your projector is from the screen or wall, the larger the image. The minimum size the image can be is
approximately 25" (0.64 m) measured diagonally when the projector is roughly 31.5 inches (0.8 m) from the wall or
screen.The largest the image can be is 300" (7.6 m) when the projector is about 393.7 inches (10 m) from the wall or
screen. Use the drawing below as a guide.
Screen size (Unit: cm/inch)
609.6 (W) ꢀ 457.2 (H) / 240 (W) ꢀ 180 (H)
Screen size
300"
487.7 (W) ꢀ 365.8 (H) / 192 (W) ꢀ 144 (H)
240"
406.4 (W) ꢀ 304.8 (H) / 160 (W) ꢀ 120 (H)
200"
365.8 (W) ꢀ 274.3 (H) / 144 (W) ꢀ 108 (H)
180"
304.8 (W) ꢀ 228.6 (H) / 120 (W) ꢀ 90 (H)
150"
243.8 (W) ꢀ 182.9 (H) / 96 (W) ꢀ 72 (H)
120"
203.2 (W) ꢀ 152.4 (H) / 80 (W) ꢀ 60 (H)
100"
162.6 (W) ꢀ 122.0 (H) / 64 (W) ꢀ 48 (H)
80"
121.9 (W) ꢀ 91.4 (H) / 48 (W) ꢀ 36 (H)
60"
81.3 (W) ꢀ 61.0 (H) / 32 (W) ꢀ 24 (H)
10.0/393.7
40"
61.0 (W) ꢀ 45.7 (H) / 24 (W) ꢀ 15 (H)
8.0/315.0
30"
50.8 (W) ꢀ 38.1 (H) / 20 (W) ꢀ 15 (H)
25"
6.7/263.8
6.0/236.
0.8
31.5
1.0
39.4
5.0/196.9
4.0/157.5
Lens center
1.3
51.
3.3/129.9
2.6/102.
2.0/78.
Distance (Unit: m/inch)
21
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Installation and Connections
Throw Distance and Screen Size
The following shows the proper relative positions of the projector and screen. Refer to the table to determine the
position of installation.
Distance Chart
Screen Width
Screen Diagonal
Screen center
Screen Height
(B)
Screen Bottom
(D)
Lens Center
B = Vertical distance between lens center and
screen center
C = Throw distance
D = Vertical distance between lens center and
bottom of screen (top of screen for ceiling
application)
Throw Angle (Ͱ)
α = Throw angle
Throw Distance (C)
NOTE: Distances may vary +/-5%.
Screen Size
B
C
D
α
Screen Size
B
C
D
α
Diagonal
inch
25
30
40
60
67
72
80
Width
inch
20.0
24.0
32.0
48.0
54.0
58.0
64.0
67.0
72.0
80.0
96.0
120.0
144.0
160.0
176.0
192.0
208.0
224.0
240.0
Height
inch
15.0
18.0
24.0
36.0
40.0
43.0
48.0
50.0
54.0
60.0
72.0
Wide – Tele
inch
Wide – Tele
degree
Diagonal
mm
635
Width
mm
508
610
813
Height
mm
381
457
610
Wide – Tele
mm
Wide – Tele
degree
inch
-2.0
-2.0
-2.0
-4.0
-4.0
-4.0
-5.0
-5.0
-5.0
-6.0
-7.0
-9.0
-11.0
-12.0
-13.0
-14.0
-16.0
-17.0
-18.0
mm
-38
-46
-61
-91
inch
6.0
7.0
mm
152
183
244
366
408
439
488
512
549
610
732
914
1097
1219
1341
1463
1585
1707
1829
28.0
34.0
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
34.0
41.0
56.0
710
860
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
870
1050
1420
2160
2410
2600
2890
3040
3260
3620
4360
5460
6560
7290
8030
8760
9490
12.1
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
9.9
12.1
12.0
11.8
11.7
11.6
11.6
11.6
11.6
11.6
11.5
11.5
11.5
11.5
11.4
11.4
11.4
11.4
11.4
11.4
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
9.9
9.9
9.7
9.6
9.6
9.6
9.6
9.6
9.6
9.6
9.5
9.5
9.5
9.5
9.5
9.5
9.5
9.5
9.5
762
12.0
11.8
11.7
11.6
11.6
11.6
11.6
11.6
11.5
11.5
11.5
11.5
11.4
11.4
11.4
11.4
11.4
11.4
9.9
9.7
9.6
9.6
9.6
9.6
9.6
9.6
9.6
9.5
9.5
9.5
9.5
9.5
9.5
9.5
9.5
9.5
10.0
14.0
16.0
17.0
19.0
20.0
22.0
24.0
29.0
36.0
43.0
48.0
53.0
58.0
62.0
67.0
72.0
46.0
70.0
1016
1524
1702
1829
2032
2134
2286
2540
3048
3810
4572
5080
5588
6096
6604
7112
7620
1170
1770
1990
2140
2380
2500
2680
2990
3590
4500
5410
6020
6630
7230
7840
85.0
1219
1361
1463
1626
1707
1829
2032
2438
3048
3658
4064
4470
4877
5283
5690
6096
914
-102
-110
-122
-128
-137
-152
-183
-229
-274
-305
-335
-366
-396
-427
-457
78.0
84.0
94.0
98.0
95.0
1021
1097
1219
1280
1372
1524
1829
2286
2743
3048
3353
3658
3962
4267
4572
102.0
114.0
120.0
128.0
143.0
172.0
215.0
258.0
287.0
316.0
345.0
374.0
403.0
431.0
84
90
106.0
118.0
141.0
177.0
213.0
237.0
261.0
285.0
309.0
333.0
356.0
100
120
150
180
200
220
240
260
280
300
90.0
108.0
120.0
132.0
144.0
156.0
168.0
180.0
8450 - 10230
9050 - 10960
• Ensure that you have adequate ventilation around your
projector so heat can dissipate. Do not cover the vents
on the side of the projector.
WARNING
* Installing your projector on the ceiling must be done
by a qualified technician.Contact your NEC dealer for
more information.
* Do not attempt to install the projector yourself.
• Only use your projector on a solid, level surface. If the
projector falls to the ground, you can be injured and
the projector severely damaged.
• Do not use the projector where temperatures vary
greatly. The projector must be used at temperatures
between 32°F (0°C) and 95°F (35°C).
Reflecting the Image
Using a mirror to reflect your projector's image enables
you to enjoy a much larger image. Contact your NEC
dealer if you need a mirror. If you're using a mirror and
your image is inverted, use the MENU and SELECT
buttons on your projector cabinet or your remote control
to correct the orientation. See page 86.
• Do not expose the projector to moisture, dust, or
smoke. This will harm the screen image.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Installation and Connections
ᕢ Making Connections
NOTE: When using with a notebook PC, be sure to connect between the projector and the notebook PC before turning on the
power to the notebook PC. In most cases signal cannot be output from RGB output unless the notebook PC is turned on after
connecting with the projector.
* If the screen goes blank while using your remote control, it may be the result of the computer's screen-saver or power
management software.
* If you accidentally hit the POWER button on the remote control, wait 60 seconds and then press the POWER button again to
resume.
Enabling the computer’s external display
Displaying an image on the notebook PC’s screen does not necessarily mean it outputs a signal to the projector.
When using a PC compatible laptop, a combination of function keys will enable/disable the external display.
Usually, the combination of the ‘Fn” key along with one of the 12 function keys gets the external display to come on
or off. For example, NEC laptops use Fn + F3, while Dell laptops use Fn + F8 key combinations to toggle through
external display selections.
Connecting Your PC or Macintosh Computer
AUDIO
COMPUTER 1
NOTE: The COMPUTER 1 connector
supports Plug & Play (DDC2).
COMPNENT
PC CARD
USB(MOUSE)
Y
Cb/Pb
Cr/Pr
USB(COMPUTER)
COMPUTER
COMPUTER
1
2
AUDIO
S-VIDO
COMPUTER 2
AUDIO
AUDIO
L/MONO
VIDEO
R
PC CONTROL
AUDIO
AC IN
RGB signal cable (supplied)
To mini D-Sub 15-pin connector on the
projector. It is recommended that you
use a commercially available distribu-
tion amplifier if connecting a signal
cable longer than the supplied one.
Audio cable (not supplied)
IBM PC or Compatibles (Desktop type)
or Macintosh (Desktop type)
PHONE
NOTE: For older Macintosh,
use a commercially available
pin adapter (not supplied) to
connect to your Mac's video
port.
PHONE
IBM VGA or Compatibles (Notebook
type) or Macintosh (Notebook type)
Connecting your PC or Macintosh computer to your projector will enable you to project your computer's screen image
for an impressive presentation.
To connect to a PC or Macintosh, simply:
1. Turn off the power to your projector and computer.
2. Use the supplied signal cable to connect your PC or Macintosh to the projector.
3. Connect the supplied power cable. See page 28.
4. Turn on the projector and the computer.
5. If the projector goes blank after a period of inactivity, it may be caused by a screen saver installed on the computer
you've connected to the projector.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Installation and Connections
NOTE: The 8768 is not compatible with video decoded outputs of special ISS-6020 and ISS-6010 switchers.
NOTE: An image may not be displayed correctly when a Video or S-Video source is played back via a commercially available scan
converter.
This is because the projector will process a video signal as a computer signal at the default setting. In that case, do the following.
* When an image is displayed with the lower and upper black portion of the screen or a dark image is not displayed correctly:
Project an image to fill the screen and then press the AUTO ADJ button on the remote control or the AUTO ADJUST button on
the projector cabinet.
* When noise appears on the sides of the screen:
Use the Overscan feature to display the image correctly.
Be sure to change the Overscan to 0% before pressing the AUTO ADJ or AUTO ADJUST button, otherwise an image may be
displayed with its sides cut off.
To connect SCART output (RGB)
Projector
COMPONENT
Y
PC CARD
USB(MOUSE)
Cb/Pb
Cr/Pr
USB(COMPUTER)
AUDIO
L/MONO
COMPUTER
COMPUTER
1
2
AUDIO
S-VIDEO
R
R
COMPUTER 2
AUDIO
L/MONO
VIDEO
PC CONTROL
AUDIO
Video equipment such as DVD player
AC IN
Female
To COMPUTER 2 input
ADP-SC1
Commercially available SCART cable
Before connections: An exclusive SCART adapter (ADP-SC1) and a commercially available SCART cable are re-
quired for this connection.
NOTE: Audio signal is not available for this connection.
1. Turn off the power to the projector and your video equipment.
2. Use the NEC ADP-SC1 SCART adapter and a commercially available SCART cable to connect the RGB input of
your projector and a SCART output (RGB) of your video equipment.
3. Connect the supplied power cable. See page 28.
4. Turn on the power to the projector and your video equipment.
5. Use the COMPUTER 2 button on the remote control to select the COMPUTER 2 input.
6. Press the MENU button on the remote control to display the menu.
7. From the menu, select [Setup] → [Page3] → [Signal Select] → [Computer 2] → [Scart].
SCART is a standard European audio-visual connector for TVs, VCRs and DVD players. It is also referred to as
Euro-connector.
NOTE: The ADP-SC1 SCART adapter is obtainable from your NEC dealer in Europe. Contact your NEC dealer in Europe for more
information.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Installation and Connections
Connecting an External Monitor
MONITOR OUT
COMPONENT
Y
PC CARD
USB(MOUSE)
AUDIO
Cb/Pb
Cr/Pr
UB(COMPUTER)
MONITOUT
AUDIO
L/MONO
COMPTER
COMPTER
1
2
AUDIO
S-VIDEO
R
R
AUDIO
L/MONO
VIDEO
PC COROL
AUDIO
AC IN
RGB signal cable (supplied)
RGB signal cable (not supplied)
You can connect a separate, external monitor to your projector to simultaneously view on a monitor the RGB analog
image you're projecting.
To do so:
1. Turn off the power to your projector, monitor and computer.
2. Use a 15-pin cable to connect your monitor to the MONITOR OUT (Mini D-Sub 15 pin) connector on your projector.
3. Connect the supplied power cable. See page 28.
4. Turn on the projector, monitor and the computer.
NOTE:
• The MONITOR OUT connector outputs RGB signal during Idle mode. When the projector goes into standby mode, the image on
an external monitor disappears for a moment.
• When the projector is in the standby mode, the image may not be correctly displayed while the cooling fans are running
immediately after turning on or off the power.
• Daisy chain connection is not possible.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Installation and Connections
Connecting Your DVD Player with Component Output
COMPONENT
Component video RCAꢀ3
COMPONENT
Y
PC CARD
USB(MOUSE)
Cb/Pb
Cr/Pr
USB(COMPUTER)
cable (not supplied)
AUDIO
L/MONO
MONITOR OUT
AUDIO
COMPUTER
1
AUDIO
S-VIDEO
R
R
AUDIO
L/MONO
NOTE: The "Y" connector accepts
a Video signal. A Video signal
will be automatically displayed. If
not, from the menu, select
[Setup] → [Page 3] → [Signal
Select] → [Component] →
[Video].
VIDEO
PC CONTROL
COMPUTER
2
AUD
AUDIO
AC IN
Audio Equipment
DVD player
L
R
Y
Cb Cr
AUDIO IN
AUDIO OUT
Component
L
R
Audio cable (not supplied)
You can connect your projector to a DVD player with component output or Video output. To do so, simply:
NOTE: For a DVD player without component video (Y,Cb,Cr/Y, Pb, Pr) output, use an S-Video cable (not provided) to connect an
S-Video output of the DVD player to the S-VIDEO input of the projector.
1. Turn off the power to your projector and DVD player.
2. If your DVD player has the component video (Y,Cb,Cr/Y, Pb, Pr) output, use a commercially available component
video cable (RCAꢀ3) to connect your DVD player to the COMPONENT input connectors on the projector.
Use an audio cable (not supplied) to connect the audio from your DVD player to your audio equipment (if your DVD
player has this capability). Be careful to keep your right and left channel connections correct for stereo sound.
3. Connect the supplied power cable. See page 28.
4. Turn on the projector and DVD player.
NOTE: Refer to your DVD player's owner's manual for more information about your DVD player's video output requirements.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Installation and Connections
Connecting Your VCR or Laser Disc Player
VIDEO
S-VIDEO
COMPONT
Y
PC CARD
USB(MOUSE)
AUDIO
Cb/Pb
Cr/Pr
USB(COMPUTER)
AUDIO
MONITOR OUT
COMPUTER
1
AUDIO
S-VIDEO
L/MONO
R
R
AUDIO
L/MONO
VIDEO
PC CONTROL
COMPUTER
2
AUDIO
AC IN
S-Video cable (not supplied)
Video cable (not supplied)
Audio equipment
VCR/ Laser disc player
L
R
S-VIDEO VIDEO
VIDEO OUT
AUDIO IN
AUDIO OUT
L
R
Audio cable (not supplied)
Use an RCA or S-Video cable (not provided) to connect the video and use RCA cables (not provided) to connect
the audio from your VCR, laser disc player or document camera to your projector.
To make these connections, simply:
1. Turn off the power to the projector and VCR, laser disc player or document camera.
2. Connect one end of an RCA cable to the video output (or one end of an S-Video cable to the S-Video output
connector) on the back of your VCR or laser disc player, connect the other end to the appropriate video input
on your projector. Connect one end of a pair RCA cables (not supplied) to the audio output on the back of your
VCR or laser disc player, connect the other end to your audio equipment or to the appropriate audio input on
the projector.
Be careful to keep the right and left channel connections correct for stereo sound.
3. Connect the supplied power cable. See page 28.
4. Turn on the projector and the VCR or laser disc player.
NOTE: Refer to your VCR or laser disc player owner's manual for more information about your equipment's video output
requirements.
NOTE: An image may not be displayed correctly when a Video or S-Video source is played back in fast-forward or fast-rewind via
a scan converter.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Installation and Connections
Connecting the Supplied Power Cable
Connect the supplied power cable to the projector.
First connect the supplied power cable's two-pin plug to the AC IN of the projector, and then connect the other plug of
the supplied power cable in the wall outlet.
S
U
C
O
F
M
O
O
Z
Pr
Pr
T
LAMP
STATUS
POWER
S
JU
D
A
/Pb
O
T
U
A
Y
R
R
Y
B
DIO
L/MONO
DIO
L/MONO
D
AN
COMPONENT
/ST
N
O
SOURCE
U
N
E
M
3D REFORM
T
C
E
VIDEO
L
E
E
S
C
SE)
U
O
N
A
C
B(M
US
R
TER)
COMPUTER
2
E
E
N
T
PC CARD
PU
M
O
(C
B
S
U
AUDIO
PC CARD
MONITOR O
PC CONTROL
IN
C
A
→ To wall outlet
Make sure that the prongs are fully
inserted into both the AC IN and the
wall outlet.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Projecting an Image
(Basic Operation)
ᕡ Turning on the Projector............................................. 30
ᕢ Selecting a Source .................................................... 32
ᕣ Adjusting the Picture Size and Position ..................... 33
ᕤ Correcting Keystone Distortion .................................. 35
ᕥ Optimizing RGB Picture Automatically ...................... 37
ᕦ Turning Up or Down Volume ...................................... 37
ᕧ Turning off the Projector............................................. 38
ᕨ After Use.................................................................... 38
29
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Projecting an Image (Basic Operation)
This section describes how to turn on the projector and to project a picture onto the screen.
ᕡ Turning on the Projector
NOTE:
• The projector has two power switches: a main power switch and a POWER (ON/STAND BY) button (POWER ON and OFF on the
remote control).
• When plugging in or unplugging the supplied power cable, make sure that the main power switch is pushed to the off (ꢁ)
position. Failure to do so may cause damage to the projector.
To turn on the main power to the projector, press
the Main Power switch to the on position ( I ).
r
LAMP
STATUS
POWER
OFF
ON
After you turn on your projector, ensure that the
computer or video source is turned on and that your
lens cap is removed.
POWER
AUTDJ.
C
VIDEO
COMPUTER
SELECT
SOURCE
AUTO ADJUST
ON/SND BY
1
2
S-VIDEO
LAMP
STATUS
POWER
3D REFORM
Only after you press the POWER (ON/STAND BY)
button on the projector cabinet or POWER ON but-
ton on the remote control for a minimum of 2 sec-
onds will the power indicator turn to green and the
projector become ready to use.
PC CARD
SELECT
L
NOTE: When no signal is available, a blue, black or logo screen is displayed.
When the projector displays a blue or a black screen (not logo), the Eco mode will be automatically selected in "Lamp Mode."
30
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Projecting an Image (Basic Operation)
Note on Startup screen (Menu Language Select screen)
When you first turn on the projector, you will get the Startup screen.This screen gives you the opportunity to select one
of the 19 menu languages.
To select a menu language, follow these steps:
1. Use the SELECT ̆ or ̄ button to select one of the
19 languages for the menu.
OFF
ON
POWER
AUTO ADJ.
COMPONENT
VIDEO
S-VIDEO
COMPUTER
1
2
SELECT
SOURCE
AUTO ADJUST
ON/STAND BY
LAMP
STATUS
POWER
3D REFORM
SELECT
L
E
T
C
N
R
2. Press the ENTER button to execute the
selection.
OFF
ON
POWER
AUTO ADJ.
COMPONENT
VIDEO
S-VIDEO
COMPUTER
SELECT
1
2
SOURCE
AUTO ADJUST
ON/STAND BY
LAMP
STATUS
POWER
3D REFORM
After this has been done, you can proceed to the menu
operation.
PC CARD
SELECT
If you want, you can select the menu language later.
See "Language" on page 86.
E
L
E
T
C
N
R
NOTE: Immediately after turning on the projector, screen flicker may occur. This is not a fault. Wait 3 to 5 minutes until the lamp
lighting is stabilized.
When the Lamp mode is set to Eco, the Lamp indicator will light green.
If one of the following things happens, the projector will not turn on.
• If the internal temperature of the projector is too high, the projector detects abnormal high temperature. In this
condition the projector will not turn on to protect the internal system. If this happens, wait for the projector's internal
components to cool down.
• When the lamp reaches its end of usable life, the projector will not turn on. If this happens, replace the lamp. See
page 107.
• If the lamp fails to light, and if the STATUS indicator flashes on and off in a cycle of six times, wait a full minute and
then turn on the power.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Projecting an Image (Basic Operation)
ᕢ Selecting a Source
Selecting the computer or video source
Using the Remote Control
Press any one of the COMPUTER 1/2, COMPONENT,VIDEO,
S-VIDEO or VIEWER buttons.
OFF
ON
POWER
AUTO ADJ.
COMPONENT
VIDEO
S-VIDEO
SELECT
COMPUTER
SOUE
AUTO ADJUST
ON/STAND BY
1
2
LAMP
STATUS
POWER
3D RE
Selecting from Source List
PC CARD
Press and quickly release the SOURCE button on the projec-
tor cabinet to display the Source list. Each time the SOURCE
button is pressed, the input source will change as follows:
"Computer 1/2", "Component" (DVD player), "Video" (VCR or
laser disc player), “S-Video" or "Viewer" (slides on a PC card).
To display the selected source, press the ENTER button.
SELECT
L
T
PJ
Detecting the Signal Automatically
PJ
Press and hold the SOURCE button for a minimum of 1 sec-
ond, the projector will search for the next available input
source. Each time you press and hold the SOURCE button
for a minimum of 1 second, the input source will change as
follows:
SELECT
3D REFORM
SOURCE
SOUE
AUTO ADJUST
ON/STAND BY
LAMP
STATUS
POWER
ASPECT POINTER VIER
3D RE
VOLUME MAGNIFY
PC CARD
PICTURE
PIC-MUTE
FREEZE
HELP
Computer1 → Computer2 → Component →Video → S-Video
→ Viewer → Computer1 → ...
If no input signal is present, the input will be skipped. When
the input source you wish to project is displayed, release the
button.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Projecting an Image (Basic Operation)
ᕣ Adjusting the Picture Size and Position
Place your projector on a flat level surface and ensure that the projector is
square to the screen.
Lift the front edge of the projector to center the image vertically.
If the projected image does not appear square to the screen then use the
Keystone feature for proper adjustment. See pages 35 and 44.
Rotate the projector's front right or left (to the right in this example) to center
the image horizontally on the screen.
Adjust the Tilt Foot
Adjustable Tilt
Foot Button
1. Lift the front edge of the projector.
1
2
R
E
T U
T A
2. Push up and hold the AdjustableTilt Foot Button on the front of the
projector to extend the adjustable tilt feet (maximum height: 30mm/
1.2”).
S
W
O
P
P
Y
B
S
L A M
D
N
A
T
S
/
N
O
T
S
U
M
J
D
R
A
O
F O
E
T
U
R
A
3 D
C E
R
R D
A
U
O
C
S
C
P
L
E C N
A
C
R
E
T
T
C
E
N
L
E
S
U
N
E
M
ZO
O
M
F
O
C
U
S
3. Lower the front of the projector to the desired height.
Adjustable Tilt Foot
4. Release the Adjustable Tilt Foot Button to lock the Adjustable tilt
foot.
There is approximately 10 degrees of up and down adjustment for
the front of the projector.
P O W E R
S T A T U S
L A M P
/ S T A N D B Y
O N
S T
J U
A U T O A D
3 D R E F O R M
S O U R C E
P C C A R D
L
E C N
A
C
3
R
E
T
N
S E L E C T
Adjusting the height of a projected image or changing projection
angle will run the Auto Keystone correction function to quickly
correct the vertical distortion.The "Keystone" screen will be dis-
played.
U
N
E
M
ZO
O
M
FOCUS
For operating the "Keystone" screen, see "ᕤ Correcting Vertical
4
Keystone Distortion" on page 35.
NOTE: Your "Keystone" correction data can be reset by pressing and holding the 3D
REFORM button for a minimum of 2 seconds.
CAUTION
Do not use the tilt-foot for purposes other than originally intended.
Misuses such as gripping the tilt-foot or hanging on the wall can cause dam-
age to the projector.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Projecting an Image (Basic Operation)
Zoom
Use the ZOOM lever to finely adjust the image size on the screen.
You can use the ZOOM lever to enlarge or reduce an image size.
FO
CU
S
Z
O
O
M
Focus
Use the FOCUS ring to obtain the best focus.
F
O
C
U
S
ZOOM
34
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Projecting an Image (Basic Operation)
ᕤ Correcting Keystone Distortion
Auto Keystone Correction
The Auto Keystone correction feature will correct vertical distortion of a projected image on the screen. No special
operation required. Just put the projector on a flat surface.
Manual Keystone Correction
You can also correct keystone distortion manually.
To do so:
1. Extend the Adjustable Tilt Foot to adjust the height of a projected
image. See page 33.
The Keystone screen will be displayed on the screen.
•
If the Keystone screen disappears, press the MENU button or
ENTER button once to display the Keystone screen again.
Projected area
Screen frame
2. Align the left (or right) side of the screen with the left (or right)
side of the projected image.
•
•
Use the shorter side of the projected image as the base.
In the right example, use the left side as the base.
NOTE: When "Manual" is selected in "Keystone" from the menu, project an image
adjusting projector position so that the screen is smaller than the area of the
projected image. See page 87 for selecting "Manual" in "Keystone".
Align left side
3. Use the SELECT ̇ or ̈ button to select “Horizontal”.
Perform the keystone correction.
4. If the right and left sides of the projected image are not parallel to
each other, use the SELECT ̄ button to select “Vertical” and use
the SELECT ̇̈ button.
Fine adjust so that both sides are parallel to each other.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Projecting an Image (Basic Operation)
5. Repeat steps 3 and 4 to correct keystone distortion.
6. After completing Keystone correction, press the ENTER button.
The Keystone screen will disappear.
• To perform Keystone correction again, press the 3D REFORM button
to display the Keystone screen and repeat above steps 1 to 6.
NOTE:
• Turning on the projector will reset the previous correction setting values if the projection angle is changed from the last use.
If the projection angle is the same as in the last use, the previous correction setting values are retained in the memory.
To use the previous correction setting values after changing projection angle, select "Manual" in "Keystone" from the menu. See
page 87.
To return the 3D Reform correction setting values to the factory preset, press and hold the 3D REFORM button for a minimum
of 2 seconds.
• Each time the 3D REFORM button is pressed, the item will change as follows: Keystone → Cornerstone → None → Keystone
→ ...
For information on “Cornerstone”, see “Correcting Horizontal and Vertical Keystone Distortion (Cornerstone) on page 44.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Projecting an Image (Basic Operation)
ᕥ Optimizing RGB Picture Automatically
Adjusting the Image Using Auto Adjust
Optimizing an RGB image automatically.
Press the Auto Adjust button to optimize an RGB image automatically.
[Poor picture]
OFF
ON
POWER
AUTO ADJ.
COMENT
VIDEO
S-VIDEO
COMPUTER
1
2
SELECT
SOURCE
AUTO JUST
ON/S
LAMP
STATUS
POWER
3D REFORM
PC CARD
SELECT
[Normal picture]
Press the Auto Adjust button to fine-tune the computer image or to remove any vertical band-
ing that might appear and to reduce video noise, dot interference or cross talk (this is evident
when part of your image appears to be shimmering). This function adjusts the clock frequen-
cies that eliminate the horizontal banding in the image. This function also adjusts the clock
phase to reduce video noise, dot interference or cross talk. (This is evident when part of your
image appears to be shimmering.)
This adjustment may be necessary when you connect your computer for the first time.
NOTE:
• Some signals may not be displayed correctly or take time.
• The Auto Adjust function does not work for component and video signals.
• If the Auto Adjust operation cannot optimize the RGB signal, try to adjust Clock and Phase manually.
See page 84.
ᕦ Turning Up or Down Volume
PJ
Sound level from the speaker and the AUDIO OUT
jack (Stereo mini) on the projector can be adjusted.
3D REFORM
SOURCE
ASPECT POINTER VIEWER
Increase volume
Decrease volume
VOLUME MAGNIFY
SLIDE
PICTRE
PI
FREEZE
HELP
37
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Projecting an Image (Basic Operation)
ᕧ Turning off the Projector
To turn off the projector:
First, press the POWER (ON/STAND BY) button on the projec-
tor cabinet or the POWER OFF button on the remote control for
a minimum of two seconds.
OFF
ON
POWER
AUTO ADJ.
COMPONENT
VO
COMPUTER
SELECT
SOURCE
AUTO ADJUST
ON/SND BY
1
2
LAMP
STATUS
POWER
3D REFORM
PC CARD
The power indicator will glow orange. After the projector turns
off, the cooling fans keep operating for 10 seconds (Cooling-off
time).
SELECT
L
Secondly, turn off the Main Power switch. The power indicator
will go out.
Finally unplug the power cable.
/r
CAUTION
Do not unplug the power cable from the wall outlet or do not turn off
the main power under any one of the following circumstances.
Doing so can cause damage to the projector:
• While the Hour Glass icon appears.
• While the cooling fans are running. (The cooling fans continue to
work for 10 seconds after the projector is turned off).
ᕨ After Use
Preparation: Make sure that the projector is not turned on.
1. Unplug the power cable.
2. Disconnect any other cables.
3. Retract adjustable tilt feet if extended.
4. Cover the lens with the lens cap.
5. Put the projector and its accessories in the supplied soft carrying case.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Convenient Features
ᕡ Switching Operation Mode between
Computer and Projector ........................................ 40
ᕢ Turning Off the Image and Sound.............................. 40
ᕣ Freezing a Picture...................................................... 40
ᕤ Using the Pointer ....................................................... 41
ᕥ Enlarging and Moving a Picture................................. 41
ᕦ Getting the On-line Help ............................................ 42
ᕧ Using a USB Mouse .................................................. 42
ᕨ Using the Remote Mouse Function ........................... 43
ᕩ Correcting Horizontal and Vertical Keystone
Distortion (Cornerstone) ........................................ 44
µ Making Freehand Drawings
on a Projected Image (ChalkBoard) ...................... 47
¸ Storing Images Displayed on the Projector
on the PC card or USB Memory (Capture) ............ 48
¹ Preventing the Unauthorized Use of the Projector .... 49
Ƹ Using a USB Memory Device or
USB Memory Card Reader.................................... 54
39
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Convenient Features
ᕡ Switching Operation Mode between Computer and Projector
The three shaded buttons shown on the drawing work as a computer mouse in the Computer mode.
In the Computer mode the PJ button is not lit.
Works as a mouse for your computer.
Works as the SELECT button on the projector.
OFF
ON
OFF
ON
POWER
POWER
AUTO ADJ.
COMPONENT
VIDEO
S-VIDEO
AUTO ADJ.
COMPUTER
VIDEO
S-VIDEO
COMPUTER
1
2
1
2
COMPONENT
Works as a right-click button
for your computer.
Works as the CANCEL
button on the projector.
SELECT
SELECT
PJ
PJ
Not lit
Lit red
3D REFORM
SOURCE
3D REFORM
SOURCE
ASPECT POINTER VIEWER
ASPECT POINTER VIEWER
Works as the ENTER
button on the projector.
VOLUME MAGNIFY
SLIDE
VOLUME MAGNIFY
SLIDE
Works as a left-click
button for your com-
puter.
PICTURE
PIC-MUTE
FREEZE
HELP
PICTURE
PIC-MUTE
FREEZE
HELP
•
•
•
When the MENU button is pressed, the PJ button lights red to indicate that you are in the Projector mode,
which allows the projector menu operation using the three buttons.
If no buttons are pressed within 60 seconds, the PJ button's light goes out to indicate that you are in the
Computer mode. To enable the projector menu operation again, press the PJ button to light red.
When the PJ button is lit, if you want to use the mouse function immediately, press the PJ button to return to the
Computer mode (not lit).
During Computer mode
In Computer mode, by pressing the ENTER button for 2 seconds or more then releasing, the drag mode is set and the
drag operation can be performed simply by pressing the SELECT ̆̄̇̈ (mouse) button.To drop the item, press the
ENTER (left click) button again or press the CANCEL (right click) button.
PJ
ᕢ Turning Off the Image and Sound
Press the PIC-MUTE button to turn off the image and sound for a short period of time. Press
again to restore the image and sound.
3D REFORM
SOURCE
ASPECT POINTER VIEWER
VOLUME MAGNIFY
SLIDE
NOTE: When a picture is muted, the Eco mode will be automatically selected in "Lamp Mode."
PICTURE
PIC-MUTE
FREEZE
HELP
ᕣ Freezing a Picture
Press the FREEZE button to freeze a picture. Press again to resume motion.
PJ
3D REFORM
SOURCE
ASPECT POINTER VIEWER
NOTE: Pressing the FREEZE button will display the Capture menu that allows you to capture a freezed
image. See page 48 for more information.
VOLUME MAGNIFY
SLIDE
PICTURE
PIC-MUTE
FREEZE
HP
40
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Convenient Features
ᕤ Using the Pointer
You can use one of nine pointers to draw your
audience's attention to the portion of a projected im-
age you want.
3D REFORM
SOURCE
ASPECT POINTER VIEWER
VOLUME MAIFY
SLIDE
PICTURE
PIC-MUTE
FREEZE
HELP
NOTE: You can select one pointer from the menu. See page
99.
Press the POINTER button to display the pointer.
Press the Pointer button to
display the pointer.
Use the SELECT button to move the pointer.
Press the POINTER buton again. The pointer will dis-
appear.
OFF
ON
POWER
AUTO ADJ.
COMPONENT
VIDEO
S-VIDEO
COMPUTER
1
2
SELECT
T
R
Use the Select button to move
the pointer.
ᕥ Enlarging and Moving a Pic-
ture
3D REFORM
SOURCE
ASPECT POINTER VIEWER
VOLUME MAFY
SLIDE
You can enlarge the area you want up to 400 percent.
PICTURE
PIC-MUTE
FREEZE
HELP
To do so:
1. Press the POINTER button to display the
pointer.
2. Move the pointer to the area you want to
enlarge.
OFF
ON
POWER
AUTO ADJ.
COMPONENT
VIDEO
COMPUTER
1
2
S-VIDEO
SELECT
L
3D REFORM
SOURCE
3. Enlarge the selected area.
ASPECT POINTER VIEWER
VOLUME MAGNIFY
SLIDE
When the MAGNIFY (+) button is pressed, the
image is magnified and the magnify icon will
be displayed. To magnify the selected area,
use the SELECT ̆̄̇̈ button to move the
magnify icon and press the MAGNIFY (+)
button.
PICTURE
PIC-MUTE
EZE
HELP
4. Return the image to the original size.
3D REFORM
SOURCE
ASPECT POINTER VIEWER
Press the MAGNIFY (-) button until the
magnify icon changes to the pointer.
VOLUME MAGNIFY
SLIDE
PICTURE
PIC-MUTE
FREEZE
LP
41
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Convenient Features
OFF
ON
PJ
ᕦ Getting the On-line Help
You get the contents about Help.
POWER
AUTO ADJ.
COMPONENT
VIDEO
S-VIDEO
COMPUTER
1
2
3D REFORM
SOURCE
ASPECT POINTER VIEWER
VOLUME MAGNIFY
SLIDE
SELECT
PICTURE
PIC-MUTE
FREEZE
HELP
Display Help
Exit Help
ᕧ Using a USB Mouse
USB(MOUSE)
Using a USB mouse gives you a smooth operation. A commercially
available USB mouse can be used.
COMPONENT
Y
PC CARD
USB(MUSE)
Cb/Pb
Cr/Pr
USB(COMPUTER)
MONITOR OUT
AUDIO
UDIO
COMPUTER
1
AUDIO
S-VIDEO
L/MONO
R
R
AUDIO
L/MONO
VIDEO
PC CONTROL
COMPUTER
2
AUDIO
AC IN
NOTE: There may be some brands of a USB mouse that the projector does
not support.
Operate the Menus using the USB mouse
Mouse Cursor
When connecting a USB mouse to the projector, you get a mouse cursor on the screen.
Unless you use your USB mouse within 10 seconds, the mouse cursor disappears.
Menu Display
Clicking with the right mouse button displays the menu.
To close the menu, click anywhere in the background.
Source List Display
Click with the left button anywhere on the screen except on the menu to display the Source list.
Adjusting and Setting Display
You can select a menu item and click with the left mouse button to make adjustments and settings.
Examples
Click (or press and hold) the left mouse button ̇ or ̈ to adjust the brightness. Or click and drag the left mouse
button on the slide bar horizontally to adjust it.
To save the adjustments, click . The display is closed.
•
Click
with the left mouse button to display a description of the selected menu item.
•
•
Click and drag the title bar with the left mouse button to move the adjustment or setting dialog box.
Use the right mouse button (right-click) on the adjustment or setting dialog box to return to the previous
screen with storing changes.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Convenient Features
ᕨ Using the Remote Mouse Function
The built-in remote mouse function enables you to operate your computer's mouse functions from the remote control
(Computer mode).
It is very convenient for clicking through your computer-generated presentations. To return to the projector operation
mode (Projector mode), press the PJ button (lit red).
Connecting to your computer for the remote mouse function
If you wish to use the remote mouse function, use the supplied USB cable to connect the USB port (COMPUTER) of
the projector and the USB port (type A) of your computer.
NOTE: Depending on the type of connection or OS installed on your computer, you may have to restart your computer or change
your computer settings.
When using the USB Port
The remote mouse function can only be used with a Windows 98, Win-
dows Me, Windows XP, Windows 2000 or Mac OS operating system.
USB(COMPUTER)
COMPONENT
PC CARD
USB(MOUSE)
AUDIO
Y
Cb/Pb
Cr/Pr
USB(COMUTER)
MONITOR UT
AUDIO
L/MONO
COMPUTER
1
AUDIO
S-VIDEO
R
R
AUDIO
L/MONO
VIDEO
PC CONTL
COMPUTER
2
AUDIO
NOTE: Wait at least 5 seconds after disconnecting the USB cable before
reconnecting it and vice versa. The computer may not identify the built-in mouse
receiver if it is repeatedly connected and disconnected in rapid intervals.
AC IN
43
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Convenient Features
ᕩ Correcting Horizontal and Vertical Keystone Distortion (Cor-
nerstone)
Use the 3D Reform feature to correct keystone (trapezoidal) distortion to make the top or bottom and the left or right
side of the screen longer or shorter so that the projected image is rectangular.
Cornerstone
1. Press and hold the 3D REFORM button for a minimum of 2 seconds to reset current adjustments.
Current adjusments for “Keystone” or “Cornerstone” will be cleared.
2. Project an image so that the screen is smaller than the area of the raster.
3. Pick up any one of the corners and align the corner of the screen with the one of the image.
Projected image
The drawing shows the
upper right corner.
Screen
4. Press the 3D REFORM button on the remote control twice.
The Cornerstone adjustment screen is displayed.
5. Use the SELECT ̆̄̇̈ button to select one icon which points in the direction you wish to move the
projected image frame.
6. Press the ENTER button.
7. Use the SELECT ̆̄̇̈ button to move the projected image frame as shown on the example.
Screen
44
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Convenient Features
8. Press the ENTER button.
Screen
9. Use the SELECT ̆̄̇̈ button to select another icon which points in the direction.
On the Cornerstone adjustment screen, select “Exit” or press the CANCEL button on the remote control.
Screen
The confirmation screen is displayed.
10.Press the SELECT ̇ or ̈ button to highlight the [OK] and press the ENTER button.
This completes the keystone correction.
Selecting “Cancel” will return to the adjustment screen without saving changes (Step 3).
Selecting "Reset" will return to the factory default.
Selecting "Undo" will exit without saving changes.
NOTE: To return the 3D Reform correction setting values to the factory default, press and hold the 3D REFORM button for a
minimum of 2 seconds.
NOTE: During 3D Reform adjustment, "Aspect Ratio" and "Screen" may not be available. Should this happen, first reset the 3D
Reform data and then do each setting. Second repeat the 3D Reform adjustment. Changing Aspect Ratio and/or Screen setting
can limit 3D Reform in its adjustable range.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Convenient Features
The adjustable ranges for 3D Reform are as follows:
Horizontal
Vertical
Cornerstone
Keystone
Max. +/– 35° approx.
Max. +/– 27° approx.
Max. + 56° approx.
– 30° approx.
* The following are conditions under which the maximum angle is achived:
• Image (100") is projected in Wide (Zoom lever)
• Resolution is XGA
Higher resolution than XGA narrows the adjustable range.
• Menu items should be set as follows:
Aspect Ratio ........... 4:3
Screen Type ........... 4:3
• Horizontal and Vertical are adjusted separately.
A combination of both adjustments narrows the adjustable range.
• When "4:3 Fill" is selected in Aspect Ratio, "Cornerstone" and "Horizontal Keystone" are not available.
NOTE:
• If the Cornerstone screen is unavailable (grayed), press and hold the 3D REFORM button for a minimum of 2 seconds to reset
the current correction data. The Cornerstone function becomes available.
• Turning on the projector will reset the previous correction setting values if the projection angle is changed from the last use.
If the projection angle is the same as in the last use, the previous correction setting values are retained in the memory.
To use the previous correction setting values after changing projection angle, select "Manual" in "Keystone" from the menu. See
page 87.
NOTE: The 3D Reform feature can cause an image to be slightly blurred because the correction is made electronically.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Convenient Features
µ Making Freehand Drawings on a Projected Image
(ChalkBoard)
The ChalkBoard feature allows you to write and draw messages on a projected image.
NOTE: The ChalkBoard feature is available only when a USB three-button mouse is used.
To display or hide the ChalkBoard tool bar, click the middle button on your mouse.
The tool bar contains the following icons.
ᕨ
ᕢ
ᕣ
ᕤ
ᕥ
ᕦ
ᕧ
ᕡ
ᕡ Drag ................. Drags to move the tool bar.
ᕢ Pen ................... Left-click and drag to draw. Left-click or right-click the pen icon to display the pen palette containing four
lines of different thickness from which you can select a line you prefer by left-clicking.
ᕣ Color ................ Selects a color. Left-click to display the color palette from which you can select a color you prefer by left-
clicking.
ᕤ Capture............. Left-click to capture a drawing on the ChalkBoard screen and save it to your PC-card inserted into the PC
card slot of the projector.
ᕥ Eraser ............... Left-click and drag to erase part of a drawing. Left-click or right-click the eraser icon to display the eraser
palette containing four eraser of different thickness from which you can select an eraser you prefer by left-
clicking.
ᕦ Clear ................. Left-click to clear the drawing completely from the ChalkBoard screen.
ᕧ Hide.................. Hides the tool bar by left-clicking. Right-clicking anywhere on the screen displays the ChalkBoard tool bar
again.
ᕨ Exit ................... Clears the complete drawing and exits the ChalkBoard.
NOTE:
• The menu is not available while you display the ChalkBoard screen.
• Selecting another source or switching slides in the Viewer clears a drawing completely.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Convenient Features
¸ Storing Images Displayed on the Projector on the PC card or
USB memory (Capture)
The Capture features allows you to capture an image from a source that is currently being displayed. The image is
saved as JPEG in the PC card or USB memory.
NOTE:
• Unless a PC card or USB memory is inserted into the PC Card slot or USB (MOUSE) port of the projector, the Capture feature is
not available.
• The "Card Error" display means that the free space of the PC card or USB memory is insufficient for saving images. Make more
space available on the card by erasing unwanted images with your PC. The number of images that can be captured depends on
the size of the PC card.
• Be sure not to turn off the power or remove the PC card or USB memory while capturing an image. Doing so could cause a
loss of the data in the PC card or USB memory or damage to the card itself.
Preparations:
Insert the PC card into the PC card slot or USB (MOUSE) port of the projector.
Insert the PC card so that the end with the insertion direction arrow on the top goes in first.
* Press the eject button to eject the card.
1. Project the image you wish to store on the projector.
2. Press the FREEZE button on the remote contorol.
3. Press the MENU button to display the Capture menu.
Capture.................. Captures an image and save it as a JPEG file in a PC card or USB memory.
Drive...................... Select the PC Card or USB memory. You can capture an image and save it to your PC card or USB memory.
Exit ........................ Exits the Capture function. Another option to exit the Capture function is to press MENU or CANCEL button
on the remote control or projector cabinet.
NOTE:
Captured images with higher resolution than the projector's native resolution cannot be displayed correctly.
• File size of the captured image varies depending on the resolution of an input signal.
• An hourglass indicating that an image is being captured appears on the projector's display. Do not eject the PC card or turn off
the projector's power while this icon is displayed. Doing so will damage the PC card data. If the PC card data is damaged, use a
computer to repair the data.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Convenient Features
¹ Preventing the Unauthorized Use of the Projector
Assigning a keyword prevents the projector from being used by unauthorized individuals.
Assigning a Keyword for the first time
1. Press the MENU button.
The menu will be displayed.
2. Press the SELECT ̈ button twice to highlight the Setup submenu and press the ENTER button.
The page tab “1” will be highlighted.
3. Press the SELECT ̈ button once to highlight the page tab “2”.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Convenient Features
4. Press the SELECT ̄ button four times to highlight “Security”.
5. Press the ENTER button to display the Security screen.
6. Press the ENTER ̄ button once to highlight the Keyword entry box and press the ENTER button.
The Software keyboard will be displayed.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Convenient Features
7. Enter an alphanumeric keyword using the Software keyboard
For example, to enter “1234”, follow the steps 7-1 to 7-4 below.
NOTE:
• Please make a note of your keyword.
• Do not use spaces (SP) in your keyword.
7-1. Highlight the number “1” and press the ENTER button.
The number “1” will be displayed in the Keyword entry box.
7-2. Press the SELECT ̈ button once to highlight “2” and press the ENTER button.
The number “12” will be displayed in the Keyword entry box.
7-3. For “3” and “4”, use the same procedure as step 7-2.
The number “1234” will be displayed in the Keyword entry box.
7-4. Press the SELECT ̄ button to highlight “OK” and press the ENTER button.
The Software keyboard will disappear.
8. Press the SELECT ̆ button once to highlight “Disable” and press the SELECT ̇ button to highlight
“Enable”.
9. Press the SELECT ̄ button to highlight “OK” and press the ENTER button.
The confirmation screen will be displayed.
10.Press the ENTER button.
The Security Function is now enabled.
NOTE: A PC card can be used as a protect key. You can skip the keyword entry by inserting a registered PC card when turning on
the projector. See page 91.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Convenient Features
Checking If Security is enabled
Turn off the projector and turn it back on to check if the Security function is enabled.
1. Press and hold the POWER (ON/STANDBY) button for a minimum of two seconds.
The lamp lights off and the POWER indicator flashes orange. Please wait until the POWER indicator changes
from flashing to steady light.
2. When the POWER indicator lights steady orange, push the Main POWER switch to the off position (O).
The projector will turn off.
3. Push the Main POWER switch to the on position (I).
The POWER indicator lights orange. The projector is in standby condition.
4. Press and hold the POWER (ON/STANDBY) button for a minimum of two seconds.
The projector will turn on. The “Projector is locked! Enter your keyword.” message will be displayed at the bottom
of the screen.
5. Press the MENU button.
The on-screen menu will be displayed.
6. Press the SELECT ̈ button to highlight “Setup” and press the ENTER button.
The page tab “1” will be highlighted.
7. Press the SELECT ̈ button once to highlight the page tab “2”.
8. Press the SELECT ̄ button four times to highlight “Security” and press the ENTER button.
The Keyword entry screen will be displayed
9. Press the ENTER button.
The Software keyboard will be displayed.
10. Use the same procedures as steps 1 to 7 described in the “Assigning a Keyword for the first time”
section to enter “1234”.
Each time one number is entered, an “*” (asterisk) will appear. Keyword appears as asterisks so the real keyword
is hidden.
11. After entering your keyword, highlight “OK” and press the ENTER button.
The Software keyboard will disappear. This will allow you to operate the projector.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Convenient Features
Disabling the Security
1. Press the MENU button.
The on-screen menu will be displayed.
2. Press the SELECT ̈ button to highlight “Setup” and press the ENTER button.
The page tab “1” will be highlighted.
3. Press the SELECT ̈ button once to highlight the page tab “2”.
4. Press the SELECT ̄ button four times to highlight “Security” and press the ENTER button.
The Keyword entry screen will be displayed
5. Press the ENTER button.
The Software keyboard will be displayed.
6. Use the same procedures as steps 1 to 7 described in the “Assigning a Keyword for the first time”
section to enter “1234”.
Each time one number is entered, an “*” (asterisk) will appear. Keyword appears as asterisks so the real keyword
is hidden.
7. After entering your keyword, highlight “OK” and press the ENTER button.
The Software keyboard will disappear. The Security screen will be displayed.
8. Highlight “Enable” and press the SELECT ̈ button to highlight “Disable”.
9. Press the SELECT ̄ button to highlight “OK” and press the ENTER button.
The Security Function is now disabled.
NOTE: To enable the Security again, enter your keyword again. Make sure that your keyword is correct.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Convenient Features
Ƹ
Using a USB Memory Device or USB Memory Card Reader
The projector is compatible with either a USB memory device or
USB memory card reader which supports the viewer and security
features.
•
•
•
To use a USB memory device or USB memory card reader,
connect the device to the USB (MOUSE) port (type A).
Select one of the drive icons for your USB memory in a pane
on the left side of the Viewer window.
To use a USB memory device as a Protect key for Security
function, select one from the Drive icons in the Security setting
screen. See page 91.
COMPONENT
USB(MOUSE)
PC CARD
Y
Cb/Pb
Cr/Pr
USB(COMPUTER)
MONITOR OUT
AUDIO
L/MONO
AUDIO
COMPUTER
COMPUTER
1
2
AUDIO
S-VIDEO
R
R
AUDIO
L/MONO
VIDEO
PC CONTROL
AUDIO
AC IN
NOTE:
• Some USB memory devices (brands) or USB memory card readers may not work.
• You cannot use a USB memory device and a USB memory card reader when connecting a USB mouse to the projector.
• Do not do the following while the USB memory device or USB memory card reader’s access indicator is lit or flashing (while
data is being accessed.) Doing so can damage your USB memory device or USB memory card in the reader. Back up your data
in case it will need to be restored.
* Pulling out the USB memory device or USB memory card reader from the USB port of the projector.
* Pulling out the memory card from the USB memory card reader
* Turning off the main power switch or unplugging the power cable.
• The drive for ”USB 1-4” is displayed only when the USB memory device or USB memory card reader is connected to the
projector. The drive for “USB 1-4” may be displayed differently from the one in the USB memory card reader.
• Some USB memory devices (brands) or USB memory cards cannot be used as Protect key for the projector’s Security
function.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Using the Viewer
ᕡ Making the Most out of the Viewer Function.............. 56
ᕢ Operating the Viewer Function from the Projector..... 58
» Changing Background Logo ...................................... 64
55
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Using the Viewer
ᕡ Making the Most out of the Viewer Function
Features
You can view presentation data, capture and play images on the projector.A PC card is used to view presentation data
prepared on the computer and to capture and play images projected with the projector.
The Viewer feature allows you to view slides stored on a PC memory card (referred to as PC card in this manual) or
USB memory on the projector. Even if no computer is available, presentations can be conducted simply with the
projector.This feature is convenient for holding presentations at meetings and in offices, as well as for playing images
taken on digital cameras.
NOTE:
• To use the Viewer, first you need to create presentation materials on your PC (JPEG, BMP, Index* files).
For creating presentation materials using the Dynamic Image Utility 2.0.
* “Index” file is a file created using the Dynamic Image Utility 2.0 contained on the supplied NEC Projector User Supportware
CD-ROM.
See “Using Dynamic Image Utility 2.0 on the supplied CD-ROM” for installing the Dynamic Image Utility 2.0 on your
computer.
Easy to use
•
•
•
•
Presentations can be started immediately simply by inserting a PC card or USB memory (not supplied)
Easy slide switching
Remote control operation
Jumping to a list of slides or any specific slide
High quality images
•
•
•
High resolution up to 1024 x 768 dots
24-bit full color playback
Viewing of digital camera images
Simple utility software (for computer)
•
•
•
*
Dynamic Image Utility 2.0 operable on Windows 98/Me/XP/2000
Slides can be created by capturing the currently displayed image
Control screen for displaying lists of slides and editing
Microsoft, Windows and PowerPoint are registered trademarks of Microsoft Corporation.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Using the Viewer
Inserting and Removing a PC Card
NOTE:
• Do not try to force the PC card into the slot.
• A dummy card is inserted into the PC CARD slot at the time of shipment. First remove the dummy card before use.
Inserting the PC Card
M
E
N
U
PC card (not supplied)
SELECT
N
T
E
R
•
Hold the PC card horizontally and insert it slowly into the
PC card slot with its top facing up.
C
A
N
C
E
P
C
S
C
O
A
U
R
R
C
D
E
3
D
A
R
U
T
E
O
F
A
O
R
D
J
M
U
S
T
O
N
/S
T
A
N
D
L
A
B
S
M
P
Y
T
A
P
T
O
U
W
S
P
E
R
C
C
A
RD
U
S
B
(C
O
M
P
U
TE
U
R
S
B
)
(M
O
U
S
E
)
M
O
NIT
O
R
O
U
T
L
AU
D
C
O
IO
M
P
P
O
C
C
N
E
O
N
N
T
T
C
C
R
O
O
M
P
UT
Y
C
E
R
1
2
b/
A
A
U
D
D
C
IO
r/P
r
O
M
S
P
-V
ID
U
TE
E
R
O
L
A
O
/M
/M
U
O
D
N
U
IO
V
ID
R
R
E
O
L
A
U
O
D
N
O
Eject button
M
E
Removing the PC Card
N
U
S
E
L
E
N
C
T
T
E
R
C
NOTE: Do not eject the PC card while its data is being accessed.
A
N
C
E
PC CARD
SOURCE
3D REFORM
AUTO
ADJUST
ON/STAND BY
LAMP
STATUS
POWER
Press the eject button twice. The PC card pops out a little. Grasp the
edges of the PC card and pull it out.
P
C
C
A
R
D
USB(CR)
USB(MOUS
M
P
O
N
IT
O
R
O
U
T
A
U
D
C
O
IO
M
P
C
O
C
N
E
O
N
N
T
T
C
R
O
O
M
L
P
U
Y
C
T
E
R
1
2
b
/
A
A
U
D
C
IO
r/P
C
O
M
S
P
-V
U
ID
T
E
E
O
R
L
A
/M
U
O
D
N
O
U
D
IO
V
ID
R
R
E
O
L
A
U
/M
O
D
N
O
Direction for Inserting the PC Card
The PC card has a top and bottom and must be inserted into the PC card slot in a specific direction. It cannot be
inserted backwards or upside-down.Attempting to force it into the slot in the wrong direction may break the internal pin
and damage the card slot. Refer to the PC card's operating instructions for the proper direction of insertion.
PC Card Type
The PC Card slot accepts PCMCIA Type II only.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Using the Viewer
ᕢ Operating the Viewer Function from the Projector (playback)
This section describes the operation for showing slides created using the Viewer function with the projector. It is also
possible to make slides directly from the images projected with the projector.
Projecting slides (Viewer)
Preparation: Use the Capture feature to store JPEG or BMP files in a PC card or USB memory inserted into the
projector’s slot. Or store JPEG or BMP files in a PC card or USB memory inserted into your PC.
1. Insert a PC card into the PC card slot of the projector.
2. Press the VIEWER button on the remote control or select the “Viewer” from the source list.
An image stored in the PC card will be displayed.
3. Press the MENU button to display the Viewer menu.
The Viewer menu will appear when you press the MENU button on the remote control or the projector cabinet.
The Viewer menu includes the following commands:
Play ................... Plays back automatically or manually depending on the setting in Option. This allows you to move on to the
next slide when "Manual Play" is selected in the “Play Mode”.
Stop................... This allows you to stop Auto Play while you are playing back and to resume playing from the selected slide
or folder when "Auto Play" is selected in the “Play Mode”.
Thumbnails........ Displays a list of thumbnails of JPEG or BMP files stored in the PC card inserted into the projector.
Delete ................ Deletes a captured slide(s) or all the captured slides in the Capture - specific folder.
Logo .................. Replace the default background logo with another logo in JPEG or BMP format.
Option................ Displays the Viewer setting options.
Source Select .... Displays the Source list.
4. Select “Play” and then press the ENTER button to display the first slide or to start playing slides auto-
matically.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Using the Viewer
Viewer Window Elements
Thumbnail/file name
Number of files
Highlight
?
Slot 1
_CAP_
_RESTORE
RECYCLED
3 Files
List of folders
0000.jpg
0001.jpg
0002.jpg
Scroll bar
Cursor (orange)
Information
1/3 0000.jpg
60KB
select : ENTER folder : CANCEL
Highlight .................................. Indicates the selected folder or drive.
List of folders .......................... Indicates folders contained on a PC card or USB memory.
Information.............................. Indicates information of the selected file or folder
Folder: folder name, creation date, creation time
File: slide number/number of displayable slides in a folder, file name, creation date, creation time,
file size
Number of files ........................ Indicates number of displayable slides in the selected folder. The maximum number of images
recognized as slides within one directory is 128.
Thumbnail/file name ................ Indicates thumbnails and names contained in a folder.
Cursor ..................................... Indicates the selected slide.
Scroll bar ................................. Uses to view folders or files not visible in the window.
59
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Using the Viewer
Setting Option for Viewer
Play Mode:
Manual .................. Views a slide manually when the Viewer source is selected.
Auto ...................... Plays back slides automatically when the Viewer source is selected.
Interval:
Specifies interval time between 5 and 300 seconds.
Start:
Specifies start screen when the Viewer source is selected.
Show Thumbnails:
Selecting the Viewer source will display a list of thumbnails of JPEG or BMP files stored in the PC card or USB
memory when “On” is selected.
“Off”
?
Slot 1
_CAP_
_RESTORE
RECYCLED
3 Files
0000.jpg
0001.bmp
0002.jpg
“On”
?
Slot 1
3 Files
_CAP_
_RESTORE
RECYCLED
0000.jpg
0001.jpg
0002.jpg
1/3 0000.jpg
60KB
select : ENTER folder : CANCEL
1/3 0000.jpg
60KB
select : ENTER folder : CANCEL
NOTE: If no memory card is inserted in the PC CARD slot, there is no signal, and a black, blue or logo background is displayed,
depending on the setting. Playback is stopped when ̇̈ button on the cabinet or remote control is pressed in Auto Play mode.
60
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Using the Viewer
Switching to Slides Directly from Other Input Modes
With this function it is possible to switch directly to a slide when the picture of a VCR or computer is being projected.
Example: When conducting presentations using a combination of slides and moving pictures from a VCR, etc., it is
possible to switch from a Viewer slide to the video picture then back to the Viewer slide simply by using the Viewer
button.
NOTE: Even if you switch the current Viewer source to another source, the current slide is retained. When you return back to the
Viewer, you will get the slide that has been retained.
Viewing Digital Images
Digital images can be played with the Viewer if the following conditions are met:
•
•
If the image can be stored on an MS-DOS format PC card.
If the image can be stored in a format supported by the Viewer. With the Viewer, images on the card are
searched for in directories and images in JPEG or BMP format are recognized as slides. Searchable directories
are directories within two steps from the root directory, and searchable images are images within the first 12
files in the directory. Only file and slide switching are possible.
NOTE: The maximum number of images recognized as slides within one directory is 128.
61
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Using the Viewer
Deleting Captured Images
Using the Delete command on the Viewer menu allows you to delete captured images.
To delete captured images:
Preparation: Make sure that the PC card is inserted into the PC card slot of the projector.
1. Press the VIEWER button on the remote control to display an image.
2. Press the MENU button to display the Viewer menu.
3. Use the ̄ button to select “Thumbnails” and then press the ENTER button.
The Thumbnail screen will be displayed.
?
Slot 1
_CAP_
_RESTORE
RECYCLED
3 Files
0000.jpg
0001.jpg
0002.jpg
1/3 0000.jpg
60KB
select : ENTER folder : CANCEL
NOTE: To change highlight from the Thumbnails screen (pane on the right) to a directory tree (pane on the left) , press the
CANCEL button. To return highlight to the Thumbnails screen, press the ENTER button.
4. Use the ̆̄̇̈ buttons to select an image you wish to delete.
5. Press the MENU button to display the Viewer menu.
6. Use the ̄ button to select “Delete” and then press the ENTER button.
A confirmation message will be displayed.
7. Use the ̇ button to select “OK” and then press the ENTER button.
62
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Using the Viewer
This completes deleting.
To delete all the captured images:
1. Repeat steps 1 to 3 in the above described procedure.
2. Press the CANCEL button to select the “__CAP__” folder in the directory (pane on the left).
?
Slot 1
__CAP__
_RESTORE
RECYCLED
3 Files
0000.jpg
0001.jpg
0002.jpg
1/3 0000.jpg
60KB
select : ENTER
3. Press the MENU button to display the Viewer menu.
4. Use the ̄ button to select “Delete” and then press the ENTER button.
A confirmation message will be displayed.
5. Use the ̇ button to select “OK” and then press the ENTER button.
This completes deleting.
NOTE: The vacant "__CAP__" folder stays even after you delete all the captured images.
63
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Using the Viewer
ᕣ Changing Background Logo
You can change the default background logo using the Viewer feature.
NOTE: File size must be 256KB or less. Other file formats than JPEG and BMP are not available.
Preparation:
Use the Capture feature to store JPEG or BMP files in a PC card inserted into the projector’s slot. Or store JPEG
or BMP files in a PC card inserted into your PC’s slot and insert the PC card into the projector’s slot.
1. Press the VIEWER button on the remote control to display an image.
2. Press the MENU button to display the Viewer menu.
3. Use the ̄ button to select “Thumbnails” and then press the ENTER button.
The Thumbnail screen will be displayed.
?
Slot 1
_CAP_
_RESTORE
RECYCLED
3 Files
0000.jpg
0001.jpg
0002.jpg
1/3 0000.jpg
60KB
select : ENTER folder : CANCEL
NOTE: To change highlight from the Thumbnails screen (right window) to a directory tree (left window) , press the CANCEL
button. To return highlight to the Thumbnails screen, press the ENTER button.
4. Use ̆̄̇̈ button to select a JPEG or BMP file (slide) for your background logo.
5. Press the MENU button to display the Viewer menu.
6. Use the ̄ button to select "Logo" and then press the ENTER button.
A confirmation dialog box will be displayed.
7. Use the ̇ button to select “OK” and press the ENTER button.This completes changing a logo for the
background.
*
Once you have changed the background from the NEC logo to another, you cannot return the logo to back-
ground even by using “Reset”.
64
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Using Dynamic Image Utility 2.0
on the supplied CD-ROM
(English version only)
ᕡ End User License Agreement................................... 66
ᕢ Introduction............................................................... 67
ᕣ Operating Environment............................................. 68
ᕤ Equipment Connections and Settings ...................... 69
ᕥ Software Installation ................................................. 69
ᕦ Starting/Exiting the Software .................................... 70
ᕧ Troubleshooting ........................................................ 72
65
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Using Dynamic Image Utility 2.0 on the supplied CD-ROM
Be sure to read this before installing and using the accompanying software.
ᕡ END USER LICENSE AGREEMENT
PLEASE READ THIS SOFTWARE LICENSE AGREEMENT ("LICENSE") CAREFULLY BEFORE INSTALLING THE
SOFTWARE. IT PROVIDES THE TERMS OF THIS LICENSE.
WHILE INSTALLINGTHE SOFTWARE, THIS SOFTWARE LICENSE AGREEMENTWILL BE DISPLAYED.BY CLICK-
ING ON THE "Yes" BUTTON, YOU ARE CONSENTING TO BE BOUND BY THIS AGREEMENT. FOLLOW THE
DIRECTIONS ON THE SCREEN AND COMPLETE THE INSTALLATION PROCESS.
IFYOU DO NOT AGREE TO ALL OF THE TERMS OF THIS AGREEMENT, CLICK THE "No" BUTTON.THE INSTAL-
LATION PROCESS WILL NOT CONTINUE.
Viewtechnology,Ltd.("NECVT") grants you ("User") a license to use the PROJECTOR USER SUPPORTWARE
("Software") provided with this End User License Agreement ("EULA"). User assumes responsibility for the selection,
adoption use and the result of use of the Software to achieve its intended result.
1.Term
1) EULA will become effective upon User's agreement to the terms of EULA and shall remain in force until User
terminates it by returning or destroying the Software and its related documents.
2) Notwithstanding the foregoing NECVT may terminate EULA at any time upon User failing to abide by any terms
of EULA.Upon the termination of the EULA by NECVT, the license granted to User shall be terminated automati-
cally. User agrees to destroy the Software together with all copies of it upon such termination.
2. License
User use the Software on personal computers only for operating NECVT's projector supplied with the Software or
other projector to be specified by NECVT("Projector")
3. Replication, modification and merger of the Software
1) User may make copies of the Software and related documentation to the extent necessary for using the Projec-
tor. User agrees to reproduce the NECVT's copyright notice and other notice on any such copies.
2) User may not use, copy, modify, or otherwise dispose of the Software, except as expressly permitted in EULA.
3) No provision in EULA shall be construed to assign and/or transfer any intellectual property right in the Software
to User.
4.Transfer of the Software
1) User may transfer the Software to any third party, provided always that:
a) User must transfer, with the Software, to such third party EULA and all the related
documentation with all copies thereof, and must not retain any copy thereof.
b) Such third party has agreed to the terms and conditions of EULA.
2) Except as otherwise expressly permitted above, User may not sublicense, assign, transfer or otherwise dispose
of the license for the Software.
5. Reverse Engineering
User may not reverse engineer, decompile, and/or disassemble the Software, except and only to the extent that such
activity is expressly permitted by applicable law notwithstanding this limitation.
6. Limitations of Warranty
1) Except as expressly specified herein, the Software is provided "as is" without warranty of any kind, including but
not limited to implied warranties for fitness for a particular purpose, merchantability, title and non-infringement of
any third party rights.
2) If User finds a material defect, which effects to the proper operation of the Software, in the media of the Soft-
ware, NECVT will replace such defective media at no charge, if such media is returned to distributor from which
such User purchased it within 1 month from such purchase and if NECVT determines that such defect is due to
NECVT.
66
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Using Dynamic Image Utility 2.0 on the supplied CD-ROM
7. Limitations of Liability
In no event shall NECVT be responsible for any indirect, consequential or special damages or lost profits even if
NECVT has been advised of the possibility of such damages, and/or for any claim for compensation or damage by any
third party to User.
8. Others
1) The validity, interpretation, construction and performance of EULA shall be governed by the laws of Japan.
2) User shall not export the Software to any country to which such export would be prohibited by any applicable
laws.
ᕢ Introduction
Thank you for your purchase of the 8768 portable projector (hereafter referred to as "unit" or "projector").
This projector is connected to a personal computer or other equipment and clearly projects text or graphics to a
screen.
This projector is supplied with convenient software that allows presentations to be made more simply and effectively.
This guide gives an overview and describes the use of the accompanying software (contained in the CD-ROM that is
supplied with this projector). Look over this guide in conjunction with the Help functions of the software programs.
Contents of the Supplied CD-ROM
The supplied CD-ROM contains the following software programs:
• Dynamic Image Utility 2.0
• Viewer PPT Converter 2.0
• Image Express Utility 1.0 (not available on this model)
Please see the Help functions of the software programs for information about their functions and operation.
What Can Be Accomplished with the Supplied Software
Dynamic Image Utility 2.0
•
•
•
Converts PowerPoint files, JPEG images, and other files and creates slides that can be displayed with the viewer
function of the projector.
Captures portions of the image from the screens of word processors, spreadsheets, browsers, and other pro-
grams for use in presentations.
By saving the created slides on a flash memory card (*) and inserting the card into the PC Card slot of the
projector, the slides can be projected to the screen without connecting a personal computer.
* Please purchase a commercially available PCMCIA Type 2 (ATA specification) flash memory card.
•
The connection of personal computers and projectors by means of connection with serial cable (*) allows the
following uses.
* A network connection is not abailable on this model.
(1) Images and slides can be sent from the personal computer to the projector and then projected to the screen.
When using Microsoft PowerPoint 2000/2002, slides can be sent synchronized with the slide show page feed.
(2) A personal computer can be used to switch the projector power on/off, control the adjustment of image
quality and other settings, and to display the remaining lamp life.
Viewer PPT Converter 2.0
•
Converts files created with Microsoft PowerPoint 95/97/2000/2002 to an independent index format with a simple
operation to enable direct playback with the viewer function of the projector.
•
When using Microsoft PowerPoint 2000/2002, Viewer PPT Converter 2.0 can be started from PowerPoint (by
means of add-in registration to PowerPoint).
67
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Using Dynamic Image Utility 2.0 on the supplied CD-ROM
Image Express Utility 1.0 (not available on this model)
•
Using a network environment, this program enables the screen image displayed by the personal computer to be
sent to the projector and then projected to a screen.
•
Two methods are available for sending the screen image to the projector. "Continuous Transmit" automatically
sends the screen image of the personal computer at a fixed interval. "Single Frame Transmit" sends the screen
image by clicking the screen button (or pressing a key).
Information about Upgrading this Software
Please see the service page for NEC projectors (http://www.nec-pj.com/) for information about software upgrades of
NEC Projector User Supportware (i.e., Dynamic Image Utility and Viewer PPT Converter).
ᕣ Operating Environment
Supported Equipment
IBM PC/AT compatible computers
• CD-ROM drive a requirement (at time of installation)
Pentium MMX processor or higher a requirement
Pentium III 800 MHz or higher recommended
For Windows XP
CPU
Memory
• 128 MB or more a requirement
• 192 MB or more recommended
For other operating systems
• 64 MB or more a requirement
• 128 MB or more recommended
t More memory may be necessary when other applications are run at the same time.
Windows 98
Supported OS
Windows 98 Second Edition
Windows Me
Windows 2000 Professional
Windows XP Home Edition
Windows XP Professional/Windows XP Tablet PC Edition
* Microsoft Internet Explorer 5.01 or higher is required for the aforementioned environments.
* Does not support Windows power-saving function.
1024 dots x 768 lines recommended
High Color (15 bit, 16 bit)
Resolution
Screen Colors
True Color (24 bit, 32 bit)
68
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Using Dynamic Image Utility 2.0 on the supplied CD-ROM
ᕤ Equipment Connections and Settings
When Making Connections with Serial Cable
What Can Be Accomplished
• Using Dynamic Image Utility 2.0, a picture or slide can be sent to the projector and then projected to a screen.
• Using the projector control function of Dynamic Image Utility 2.0 allows operations to be performed from the per-
sonal computer which include switching the projector power on/off, signal selection, and adjustment of the picture
quality.
[For Connections with Serial Cable]
Equipment to Be Prepared
• Projector (This unit)
• Personal computer
• Serial cable not included with the projector (Optional CA03D is available)
Connection at the Projector Side
Plug the serial cable into the PC CONTROL connector. (“Terminal Panel Features” and “PC Control Connector” on
pages 16 and 119)
Connection at the Personal Computer Side
Plug the serial cable into the (RS-232C) serial connector.
ᕥ Software Installation
NOTE
• Windows 98 operations will be described in examples given here.
• When using Windows 2000, please perform software installation/uninstalling with "Administrators" authority. When using Win-
dows XP, perform with "Computer Administrator" authority.
Dynamic Image Utility 2.0 Installation
Dynamic Image Utility 2.0 andViewer PPT Converter 2.0 will all be installed together.The various programs cannot be
installed individually.
Preparation:
Start Windows.
If Windows has already been started, please exit all running application software. The installation may not be com-
pleted properly unless all software has been exited.
1.Place the supplied CD-ROM in the CD-ROM drive.
The "Startup" screen will appear.
Reference
Should the "Startup" screen not appear...
1) Click [Start].
2) Click [Run (R)]. The [Run] screen will appear.
3) Enter the CD-ROM drive name (e.g., "Q: \") and then "SETUP.EXE" to [Open (O)].
4) Click [OK]. The "Startup" screen will appear.
69
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Using Dynamic Image Utility 2.0 on the supplied CD-ROM
2.Click "Please read this first" and read the Readme about Dynamic Image Utility 2.0.
3.Click "Installing the Dynamic Image Utility 2.0".
The “Welcome” screen will appear.
4.Click [Next >] at the "Welcome" screen.
The "End User License Agreement" screen will appear.
Please carefully read the contents of the "End User License Agreement".
5.If you agree, click [Yes].
If you do not agree, please click [No] and exit the installer.
6.Now, follow the operations described in the screen messages.
To cancel the installation of the supplied software part way through the installation, click [Cancel] and follow the
instructions of the dialog box.
Please remove the CD-ROM from the CD-ROM drive when the installation is completed.
Uninstalling
Dynamic Image Utility 2.0 and Viewer PPT Converter 2.0 will all be uninstalled together.The various programs cannot
be uninstalled individually.
1.Click [Start].
2.Click [Settings] → [Control Panel].
The "Control Panel" screen will be displayed.
3.Double click [Add/Remove Programs].
The "Add/Remove Programs Properties" screen will appear.
4.Click "Dynamic Image Utility 2.0" from the list.
5.Click [Add/Remove. . . ].
The "Confirm File Deletion" screen will appear.
6.Check the message and click [Yes].
7.Now, follow the operations described in the screen messages.
When the uninstall procedure is completed, there will be a return to the "Add/Remove Programs Properties" screen.
8.Click [OK].
There will be a return to the "Control Panel" screen
ᕦ Starting/Exiting the Software
Dynamic Image Utility 2.0
Start the Software
Preparation:
Install the software on the personal computer from the supplied CD-ROM. (Page 69)
The software cannot be started from the supplied CD-ROM.
From the [Start] menu click [Program] → [NEC Projector User Supportware] → [Dynamic Image Utility 2.0].
Dynamic Image Utility 2.0 will start.
Reference
• By selecting a PowerPoint file with Dynamic Image Utility 2.0 and clicking [Tools] → [Converting PowerPoint file], the
function equivalent to Viewer PPT Converter 2.0 can be executed.
70
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Using Dynamic Image Utility 2.0 on the supplied CD-ROM
Display Help
Preparation:
Please start Dynamic Image Utility 2.0.
1.Click [Help].
The [Help] menu will appear.
2.Click [Help].
The [Help] screen will appear.
Exit the Software
1.Click [File].
The [File] menu will appear.
2.Click [Exit].
Dynamic Image Utility 2.0 will close.
Viewer PPT Converter 2.0
Start the Software
Preparation:
(1) Check that Microsoft PowerPoint has been installed.Viewer PPT Converter 2.0 cannot be used unless PowerPoint
has been installed.
(2) Install the software on the personal computer from the supplied CD-ROM. (Page 69)
The software cannot be started from the supplied CD-ROM.
1.From the [Start] menu click [Program] → [Projector User Supportware] → [Viewer PPT Converter 2.0].
Dynamic Image Utility 2.0 will start.
Reference
•
A function equivalent to Viewer PPT Converter 2.0 can also be executed from the Dynamic Image Utility 2.0
[Tools] → [Converting PowerPoint file] menu.
•
Viewer PPT Converter 2.0 can also be started from the Microsoft PowerPoint 2000/2002 [Tools] → [Projec-
tor User Supportware] → [Output Viewer] menu.
Display Help
Preparation:
Please start Viewer PPT Converter 2.0.
1.Click [Help].
The [Help] menu will appear.
Exit the Software
1.Click [Exit].
Viewer PPT Converter 2.0 will close.
71
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Using Dynamic Image Utility 2.0 on the supplied CD-ROM
ᕧ Troubleshooting
In this section, the software names have been abbreviated as follows:
Dynamic Image Utility 2.0 to DIU 2.0 and Viewer PPT Converter 2.0 to PPTC 2.0.
<Problem> Installation does not complete normally.
Countermeasures
Check Points
When using Windows 2000, did you log on with "Administra-
tors" authority? When using Windows XP, did you log on with
"Computer Administrator" authority?
When using Windows 2000 or Windows XP, log on with the
authority described at the left and then install.
Has Microsoft PowerPoint 2000/2002 been installed on the
personal computer to which this projector software is being
installed?
When this projector software is installed on a personal
computer that does not have PowerPoint 2000/2002 installed,
a message to the effect of "Error in the automatic registration of
PPTViewer2.dll" will appear part way through the installation.
When the message described at the left appears part way
through the installation, add-in registration will not be made to
PowerPoint; however, the installation of this projector software
will be completed normally.
To have add-in registration made to PowerPoint, please install
this projector software to a personal computer on which
PowerPoint 2000/2002 has been installed.
<Problem> Viewer PPT Converter 2.0 does not function. (PPTC 2.0)
Countermeasures
Check Points
Has Microsoft PowerPoint been installed on the personal
computer?
Install PowerPoint on the personal computer. Or, install Viewer
PPT Converter 2.0 on a personal computer on which
PowerPoint has been installed.
<Problem> When using the projector control function, the projector power does not switch on. (DIU 2.0)
Check Points
Countermeasures
Are the personal computer and the projector connected by a
serial cable?
Connect the personal computer and the projector with an serial
cable.
<Problem> You want to delete the PowerPoint add-in registration. (PPTC 2.0)
Countermeasures
Check Points
Installing this projector software when Microsoft PowerPoint
2000/2002 has already been installed on the personal
computer, will result in the automatic registration of the add-in
to PowerPoint.
Please see the PowerPoint Help function for the method of
deleting PowerPoint add-in registrations.
The PowerPoint add-in registration will not be deleted even
when this projector software is uninstalled.
72
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Using On-Screen Menu
ᕡ Using the Menus........................................................ 74
ᕢ Menu tree .................................................................. 75
ᕣ Menu Elements.......................................................... 77
ᕤ Menu Descriptions & Functions [Adjust].................... 78
ᕥ Menu Descriptions & Functions [Image].................... 82
ᕦ Menu Descriptions & Functions [Setup] .................... 85
ᕧ Menu Descriptions & Functions [Information] .......... 100
ᕨ Menu Descriptions & Functions [Reset] .................. 101
ᕩ Entry List ................................................................. 102
73
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Using On-Screen Menu
ᕡ Using the Menus
1. Press the MENU button on the remote control or the projector cabinet to display the menu.
Submenu window
Submenu
Main menu
Currently available
buttons
The Picture menu will be displayed (factory preset).
NOTE: The commands such as ̇̈, ENTER, CANCEL in the gray bar show available buttons for your operation.
2. Press the SELECT ̇̈ buttons on the remote control the projector cabinet to display the submenu.
3. Press the ENTER button on the remote control or the projector cabinet to highlight the top item or the
first tab.
4. Use the SELECT ̆̄ buttons on the remote control or the projector cabinet to select the item you want
to adjust or set.
You can use the SELECT ̇̈ buttons on the remote control or the projector cabinet to select the tab you
want.
NOTE: You can select a tab only when the tab color is orange.
5. Press the ENTER button on the remote control or the projector cabinet to display the submenu window.
NOTE: You can also display a submenu window by pressing the SELECT ̈ button.
6. Adjust the level or turn the selected item on or off by using the SELECT ̆̄̇̈ buttons on the remote
control or the projector cabinet.
7. Press the ENTER button or the CANCEL button on the remote control or the projector cabinet.
Changes are stored until you adjust it again.
ENTER ................... Stores changes.
CANCEL................. Returns to the previous screen without storing changes.
8. Repeat steps 2 -7 to adjust an additional item, or press the CANCEL button on the remote control or the
projector cabinet to quit the menu display.
74
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Using On-Screen Menu
ᕢ Menu tree
Menu
Item
Adjust
Picture
Brightness
Contrast
Color
Manual/Auto
Hue
Sharpness
Signal Type
Preset
RGB, Component
1 to 5
Detail Settings Reference
Presentation, Video, Movie,
Graphic, sRGB
Gamma Correction
Dynamic, Natural, Black Detail
5000, 6500, 7200, 7800, 8500, 9300
Brightness RGB, Contrast RGB
Red, Green, Blue,
Color Temperature
White Balance
Color Correction
Cyan,Magenta,Yellow
Wall Color
Noise Reduction
Color Matrix
Y/C Delay
3D Y/C Separation
Vertical Enhancer
I/P Converter
Bass
Off, Blackboard, Light yellow, Light green, Light blue, Sky blue, Light rose, Pink
Video
Low, Medium, High
HDTV, SDTV
0 to 15
Motion Control On/Off On: Still, Normal, Movie
Off, 1, 2, 3
Deinterlace(Auto/Still), Interlace
-15 to +15
Sound
Treble
-15 to +15
Image
Setup
Aspect Ratio
Pixel Adjust
Position
4:3
4:3, Letterbox, Wide Screen, Crop
4:3 Window, Letterbox, Wide Screen, 4:3 Fill
16:9
Clock
Phase
Horizontal
Vertical
Overscan
Page 1
0%, 5%, 10%
Screen
Screen Type
Position
4:3, 16:9
Orientation
Desktop Front, Ceiling Rear, Desktop Rear, Ceiling Front
Language[icon]
Lamp Mode
Keystone
19 languages
Normal,Eco
Auto, Manual
Menu Display Time
Cabinet Button
Sleep Timer
Password
Manual, Auto 5 sec, Auto 15 sec, Auto 45 sec
Page 2
Unlock, Lock
Off, 0:30, 1:00, 2:00, 4:00, 8:00, 12:00, 16:00
Logo
Security
Keyword
Use Protect Key
Drive
Read
Register
Delete
Background
Blue, Black, Logo
75
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Using On-Screen Menu
ᕢ Menu tree
Menu
Item
Setup
Page 3
Signal Select
Computer1
Computer2
Component
RGB/Component, RGB, Component
RGB/Component, RGB, Component, Scart
Auto, Component, Video
Color System
Component (Video) Auto, NTSC3.58, NTSC4.43, PAL, PAL-M, PAL-N, PAL60, SECAM
Video
Auto, NTSC3.58, NTSC4.43, PAL, PAL-M, PAL-N, PAL60, SECAM
Auto, NTSC3.58, NTSC4.43, PAL, PAL-M, PAL-N, PAL60, SECAM
S-Video
OUT Terminal
Last, Computer1, Computer2, Component
Off, S2
S-Video Mode Select
Display Select
Source
On, Off
On, Off
Message
Menu Color
Color, Monochrome
On, Off
Page 4
Power Management
Power Off Confirmation On, Off
Fan Mode
Auto, High Speed
Standby Mode
Auto Start
Power-saving Mode, Idle Mode
On, Off
Remote Sensor
Front
Back
On, Off
On, Off
Page 5
Filter Usage
Lamp Hour
Communication Speed
Pointer
Clear Filter Usage Meter
Clear Lamp Hour Meter
4800, 9600, 19200, 38400
Pointer 1 to 9
Mouse
Pointer
Pointer 1 to 9
Button
Right Hand, Left Hand
Fast, Medium, Slow
Sensitivity
Information
Page 1
Page 2
Source Name
Input Terminal
Entry No.
Horizontal Frequency
Vertical Frequency
Signal Type
Video Type
Sync Type
Interlace
Sync Polarity
Remaining Lamp Time
Lamp Hour Meter
Filter Usage
Page 3
Page 4
Projector Usage
Version
BIOS, Firmware, Data
Reset
Current Signal, All Data, All Data (Including Entry List)
76
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Using On-Screen Menu
ᕣ Menu Elements
Help button
Highlight
Tab
Solid triangle
Slide bar
Close button
Radio button
Check box
Cancel button
OK button
Menu windows or dialog boxes typically have the following elements:
Highlight................ Indicates the selected menu or item.
Solid triangle ......... Indicates further choices are available. A highlighted triangle indicates the item is active.
Tab ........................ Indicates a group of features in a dialog box. Selecting on any tab brings its page to the front.
Radio button ......... Use this round button to select an option in a dialog box.
Check box ............. Place a checkmark in the square box to turn the option On.
Slide bar ................ Indicates settings or the direction of adjustment.
OK button .............. Press to confirm your setting. You will return to the previous menu.
Cancel button ........ Press to cancel your setting. You will return to the previous menu.
Close button .......... Click to close the window with saving changes. (USB mouse only)
Help button ........... Indicates that help about that feature is available (USB mouse only). Press the HELP button on the remote
control to display help.
77
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Using On-Screen Menu
ᕤ Menu Descriptions & Functions [Adjust]
Picture
[Brightness]
Adjusts the brightness level or the back raster intensity.
[Contrast]
Adjusts the intensity of the image according to the incoming signal.
You have two options: Manual/Auto.
[Color]
Increases or decreases the color saturation level (not valid for RGB).
[Hue]
Varies the color level from +/- green to +/-blue. The red level is used as reference. This adjustment is only valid for
Video, Component and TV standard inputs (not valid for RGB).
[Sharpness]
Controls the detail of the image for Video (Not valid for RGB).
Selecting Signal Type [Signal Type]
Select either the computer signal type or the component signal type.
RGB....................... Computer signal
Component............ Component signals such as Y/Cb/Cr, Y/Pb/Pr
NOTE: This feature is available on the computer signal only. If you do not get a better picture even when you set "Signal Select" to
"Component" in Setup, set this to "Component".
78
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Using On-Screen Menu
[Preset]
This option allows you to adjust neutral tint for yellow, cyan or magenta. There are 5 factory presets optimized for
various types of images, you can set user adjustable settings.
Detail Settings
This will provide you with three pages of menus that provide more detailed settings.
[Page1]
Selecting Reference Setting [Reference]
This feature allows you to use color correction or gamma values as reference data to optimize for various types of
images. You can select one of the following five settings.
Presentation ...... Recommended for presentations from a computer.
Video ................. Recommended for standard video such as a TV program.
Movie ................ Recommended for film based video such as a movie (DVD or HDTV).
Graphic .............. Recommended for viewing accurate colors in graphics.
sRGB ................. Standard color values.
Selecting Gamma Correction Mode [Gamma Correction]
Each mode is recommended for:
Dynamic ............ Creates a high-contrast picture.
Natural............... Natural reproduction of the picture.
Black Detail........ Emphasizes detail in dark areas of the picture.
Adjusting Color Temperature [Color Temperature]
This feature adjusts the color temperature using the slide bar. The range is between 5000K and 9300K.
NOTE:
* When "Presentation" is selected in "Reference", this function is not available.
* When "White Balance" settings has been changed, the color temperature value on screen does not reflect the real color
temperature.
[Page 2]
Adjusting White Balance [White Balance]
This allows you to adjust the white balance. Brightness for each color (RGB) is used to adjust the black level of the
screen; Contrast for each color (RGB) to adjust the white level of the screen.
[Page 3]
Selecting Color Correction [Color Correction]
Adjusts red, green, blue, yellow, magenta and cyan each independently to correct the tint on whole screen.
79
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Using On-Screen Menu
Using the Wall Color Correction [Wall Color]
[Interface to be determined]
This function allows for quick adaptive color correction in applications where the screen material is not white.
The following eight options are available.
• OFF
• Blackboard
• Light green
• Sky blue
• Pink
• Light yellow
• Light blue
• Light rose
Video Adjustment
Selecting Noise Reduction Level [Noise Reduction]
(not available for COMPUTER1/2 and Viewer; available for TV standard inputs)
Select one of the three levels for reducing video noise: Low, Medium or High.
NOTE: The lower the Noise Reduction level, the better the image quality by way of higher video bandwidth.
Selecting Color Matrix [Color Matrix]
Select an appropriate color matrix for your input signal, either HDTV or SDTV.
AdjustingY/C Delay Level [Y/C Delay]
Adjusts Y/C delay level.
80
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Using On-Screen Menu
Turning On/Off 3 Dimension Separation [3DY/C Separation]
This function turns on or off the 3 dimensional separation feature.
When "On" is selected, the following three options are available from the pull-down list.
Still ........................ Select this option for a still image.
Normal .................. The projector automatically makes the appropriate settings for a detected source.
Movie .................... Select this option for a moving image.
NOTE: This feature is available for NTSC3.58 of Video signal only.
Setting Vertical Edges [Vertical Enhancer]
This function enhances the vertical edges around objects in the image.
NOTE: This function is not available for an RGB and Component signal.
Selecting Interlace or Deinterlace [I/P Converter]
This function allows you to select between "Interlace" and "Deinterlace".
Deinterlace (Auto) ....... The projector automatically determines a still or moving image to display a clear picture. If selecting
"Deinterlace (Auto)" causes excess jitter or artifacts, select "Interlace".
Deinterlace (Still)......... Select when a still image is displayed. When this option is selected for a moving image, jitter or artifacts
can be seen.
Interlace ...................... Select when a moving image is displayed. This will eliminate jitter and artifacts in a moving image.
81
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Using On-Screen Menu
Controlling Bass and Treble [Sound]
You can adjust the bass and treble level of the projector speakers and AUDIO OUT (Stereo Mini Jack).
ᕥ Menu Descriptions & Functions [Image]
[Page 1]
Selecting Aspect Ratio [Aspect Ratio] (not available for Viewer)
Screen Type 4:3
Screen Type 16:9
Aspect Ratio allows you to select the best Aspect mode to display your source image.
When screen type 4:3 is selected for the source, the following selections will display:
4:3 ......................... Standard 4:3 aspect
Letter Box.............. Reduced to display the true aspect with black borders on top and bottom
Wide Screen .......... Left & Right stretched with black borders on top and bottom
Crop ...................... Left & Right stretched. Left & Right sides cut. Available for 4:3 only.
82
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Using On-Screen Menu
When screen type 16:9 is selected for the source, the following selections will display:
4:3 Window ........... Reduced to display the true aspect with black borders on right and left
Letter Box.............. Standard 16:9 aspect
Wide Screen .......... Left and right stretched to display the true aspect
4:3 Fill ................... Stretched to display in 16:9 aspect ratio
NOTE: You can adjust image positions vertically for source with black borders. See page 85 for setting
image positions.
Copyright
Please note that using this projector for the purpose of commercial gain or the attraction of public
attention in a venue such as a coffee shop or hotel and employing compression or expansion of the
screen image with a "Aspect Ratio" or "Screen" setting may raise concern about the infringement of
copyrights which are protected by copyright law.
NOTE: During 3D Reform adjustment, "Aspect Ratio" may not be available.
Should this happen, first reset the 3D Reform data and then do setting again. Second repeat the 3D
Reform adjustment.
Changing the aspect ratio can limit 3D Reform in its adjustable range.
Input
Signal
Screen
Type
4:3
4:3
Squeeze
Letterbox
Wide Screen
4:3 Screen
Crop
Letterbox
Letterbox
16:9 Screen
Wide Screen
4:3 Window
4:3 Fill
83
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Using On-Screen Menu
Adjusting Clock and Phase [Pixel Adjust]
This allows you to manually adjust Clock and Phase.
Clock
Use this item to fine tune the computer image or to remove any vertical banding that might appear. This function
adjusts the clock frequencies that eliminate the horizontal banding in the image.
This adjustment may be necessary when you connect your computer for the first time.
Phase
Use this item to adjust the clock phase or to reduce video noise, dot interference or cross talk. (This is evident
when part of your image appears to be shimmering.)
Use "Phase" only after the "Clock" is complete.
Adjusting Horizontal/Vertical Position [Position]
Adjusts the image location horizontally and vertically.
Selecting Overscan Percentage [Overscan]
Select overscan percentage (0%, 5% and 10%) for signal.
NOTE: When "4:3 Fill" or "Crop" is selected in "Aspect Ratio", this feature is not available.
84
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Using On-Screen Menu
ᕦ Menu Descriptions & Functions [Setup]
Setup [Page1]
Selecting Aspect Ratio and Position for Screen [Screen]
Screen Type
Select one of three options: 4:3 Screen or 16:9 Screen for the screen to be used. See also "Aspect Ratio" on
pages 82 and 83.
Position
This feature adjusts the vertical position of the image when viewing video with an aspect ratio selected.
When some aspect ratios are selected in Image, the image is displayed with black borders on the top and bottom.
You can adjust the vertical position between top and bottom.
NOTE: This option is available only when "16:9" is selected in Screen Type.
NOTE: During 3D Reform adjustment, "Screen Type" and "Screen Position" may not be available. To make available, first reset the
3D Reform data and then do settings again. Secondly repeat the 3D Reform adjustment. Changing "Screen Type" and "Screen
Position" can limit 3D Reform in its adjustable range.
85
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Using On-Screen Menu
Selecting Projector Orientation [Orientation]
This reorients your image for your type of projection.The options are: desktop front projection, ceiling rear projection,
desktop rear projection, and ceiling front projection.
NOTE: Selecting one of the other options than “Desktop Front” will force the “Keystone” mode to be “Manual".
Selecting Menu Language [Language]
You can choose one of 19 languages for on-screen instructions.
Setting Lamp Mode to Normal or Eco [Lamp Mode]
This feature enables you to select two brightness modes of the lamp: Normal and Eco modes. The lamp life can be
extended up to 3000 hours by using the Eco mode. Selecting Eco mode decreases fan noise compared to in Normal
mode.
Normal Mode ........ This is the default setting (100% Brightness).
Eco Mode .............. Select this mode to increase the lamp life (76% Brightness).
NOTE: If the projector is overheated in Normal mode, there may be a case where the Lamp mode automatically changes to Eco
mode to protect the projector. When the projector is in Eco mode, the picture becomes slightly darker. When the projector comes
back to normal temperature, the Lamp mode returns to Normal mode.
NOTE: When a picture is muted or there are no signals (blue or black screen), the Eco mode will be automatically selected in
"Lamp Mode."
86
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Using On-Screen Menu
Selecting Keystone Mode [Keystone]
This feature allows you to correct keystone distortion manually or automatically.
Auto ...................... This feature allows the projector to detect its tilt and correct vertical distortion automatically.
Manual .................. You can correct vertical distortion manually from the menu.
Changes will be saved even when you turn off the projector.
Selecting Menu Display Time [Menu Display Time]
This option allows you to select how long the projector waits after the last touch of a button to turn off the menu. The
preset choices are "Manual", "Auto 5 sec", "Auto 15 sec", and "Auto 45 sec". The "Auto 45 sec" is the factory preset.
Manual .................. The menu can be turned off manually.
Auto 5 sec ............. The menu will automatically be turned off in 5 seconds if no buttons are pressed within 5 seconds.
Auto 15 sec ........... The menu will automatically be turned off in 15 seconds if no buttons are pressed within 15 seconds.
Auto 45 sec ........... The menu will automatically be turned off in 45 seconds if no buttons are pressed within 45 seconds.
87
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Using On-Screen Menu
Setup [Page2]
Disabling the Cabinet Buttons [Cabinet Button]
This option turns on or off the Cabinet Button Lock function.
NOTE:
• This Cabinet Button Lock does not affect the remote control functions.
• When the cabinet buttons are locked, pressing and holding the CANCEL button for about 10 seconds will change the setting to
unlock.
Using Sleep Timer [Sleep Timer]
1. Select your desired time between 30 minutes and 16 hours: Off, 0:30, 1:00, 2:00, 4:00, 8:00, 12:00, 16:00.
2. Press the ENTER button on the remote control.
3. The remaining time starts counting down.
4. The projector will turn off after the countdown is complete.
NOTE:
• To cancel the preset time, set "Off" for the preset time or turn off the power.
• When the remaining time reaches 3 minutes before the projector is turned off, the "Projector will turn off in 3 minutes"
message will be displayed on the bottom of the screen.
88
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Using On-Screen Menu
Setting a Password [Password (Logo)]
A password can be set for your projector to avoid operation by an unauthorized person.
When a password is set, doing any one of the following two operations will display the Password input screen.
•
•
Changing the background
Changing the logo data in a PC card
Entry:
To assign your password:
NOTE: Up to 15 alphanumeric characters can be assigned.
1. Type a password.
Highlight "Entry" and press the ENTER button.
The "Enter the Password" screen will be displayed.
Make sure that is highlighted and then press the ENTER button.
The Software keyboard appears. Use the Software keyboard to type a password and then highlight "OK"
on the “Enter the Password” screen and press the ENTER button.
The [Confirm Password] screen will be displayed.
2. Type the same password again. Highlight "OK" on the “Enter the Password” screen and press the
ENTER button.
Your password will be assigned.
Delete:
To delete your password:
1. Highlight [Delete] and press the ENTER button.The "Current Password" screen will be displayed.
2. Use the Software keyboard to type your password. Highlight "OK" on the “Current Password” screen and
then press the ENTER button.
Your password will be deleted.
89
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Using On-Screen Menu
Security
The Security function enables you to protect your projector so that the projector will not project a signal unless you
enter a keyword.There is also an option to lock the projector by using a registered PC card as a protect key. Once you
have registered your PC card as a protect key, you are required to insert the registered PC card into the PC card slot
of the projector each time you turn on the projector.You can enable the Security function by using a keyword only.
Enable/Disable....... This turns the Security function on or off.
Keyword ................ Enter an appropriate keyword when you use the Security function. (Up to 10 characters can be used.) The
Security function is available only when your keyword is entered.
Use Protect key ..... Check this box to lock your projector when using a PC card. To use a keyword without a PC card, do not
check this box.
Drive...................... Switches between PC Card slot and USB port (type A).
Read ...................... Reads data from a PC card.
Register ................. Registers data from the PC card. The Security function is not available unless at least one PC card is
registered. (if the “Use Protect key” check box is selected) Up to 5 PC cards can be registered.
Delete .................... Deletes data of a registered PC card.
To set up a keyword to enable the Security function without using a registered PC card.
1. Use the SELECT ̆̄ button to select “Keyword” and use the software keyboard to enter a keyword.
NOTE: Please make a note of your keyword.
2. Use the SELECT ̆̄ button to select “Enable” and use the SELECT ̆̄ button to select “OK”, then the
Security function will be enabled.
An “Are you sure?” message will appear. Use the SELECT ̇̈ button to select “OK” and press the
ENTER button.
The Security function takes effect.
90
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Using On-Screen Menu
To register a PC card as a protect key.
1. Insert a PC card into the PC card slot of the projector.
2. Use the SELECT ̆̄ button to select "Use Protect Key" and press the ENTER button.
3. Use the SELECT ̆̄ button to select "Read" and press the ENTER button.
Data of the PC card will be read into the projector.
4. Use the SELECT ̆̄ button to select "Register" and press the ENTER button.
Downloaded data will be registered and be displayed in the list window.
5. Use the SELECT ̆̄ button to select "Keyword" and use the software keyboard to enter a keyword.
NOTE: To use a PC card as a protect key, you must also set up a keyword. Please make a note of your keyword.
This completes registration of your PC card.
To enable Security, use the SELECT ̆̄ button to select "Enable" and use the SELECT ̆̄ button to select "OK" and
"Security function will be enabled.An “Are you sure?" message will appear. Use the SELECT ̇̈ button and press the
ENTER button.
The Security function takes effect.
To turn on the projector when Security is enabled (when using your keyword only).
1. Press and hold the POWER button for a minimum of two seconds.
The projector will be turned on and display a message to the effect that the projector is security-pro-
tected.
2. Select [Setup] → [Page 2] → [Security] from the menu and press the ENTER button.
The Release Code input screen will be displayed.
3. Enter your keyword in the Release Code input screen.
You can view the projected image.
NOTE: Do not forget your keyword. However, if you forget your keyword, NEC or your dealer will provide you with your Release
Code. See more information at the end of this section.
To turn on the projector when Security is enabled (when using PC card as a protect key).
1. Insert your registered PC card into the PC card slot.
2. Press and hold the POWER button for a minimum of two seconds.
The projector will turn on and then recognize the PC card. Once the image has been projected, it will
stay on without the PC card.
•
•
The security disable mode is maintained until the main power is turned off (by setting the main power switch
to "O" or unplugging the power cord). In the following cases you will be asked to check the protect key or input
the keyword:
(1)When "OK" is selected at an image for which security is set and the power is turned off then back on
(2)When the main power is turned off then back on while the security function is enabled
(3)When you attempt to display an image for which security is set while the security function is enabled
Blanks (spaces) cannot be used in the Keyword section.
91
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Using On-Screen Menu
To delete PC card data you registered.
1. Use the SELECT ̆̄ button to select "Delete" and use the SELECT ̇ button to select the list window.
2. Use the SELECT ̆̄ button to select the PC card data you wish to delete.
3. Press the SELECT ̈ button to select "Delete" and press the ENTER button.
The PC card data will be deleted.
If you've lost your registered PC card, proceed as follows:
NOTE: NEC or your dealer will provide you with your Release Code in exchange for your registered keyword and Request Code.
See more information at the end of this section.
1. Press and hold the POWER button for a minimum of two seconds.
The projector will be turned on and display a message to the effect that the projector is security-pro-
tected.
2. Select [Setup] → [Page 2] → [Security] from the menu and press the ENTER button.
The Release Code input screen will be displayed as well as your Request Code (24 alphanumeric
characters).
3. Enter your Release Code in the Release Code Input screen.
The projector will turn on.
* If the projector is turned on by entering the Release Code, your Security will be disabled.
NOTE:
• Some types of PC cards cannot be registered as your protect key.
• It is recommended that you register two or more PC cards in case you lose or damage your registered PC card.
• Formatting your registered PC card will disable your protect key function.
NOTE:
For additional information visit:
US : http://www.necvisualsystems.com
Europe : http://www.nec-europe.com/
Global : http://www.nec-pj.com/
Selecting a Color or Logo for Background [Background]
Use this feature to display a blue/black screen or logo when no signal is available.The default background is blue.You
can change the logo screen using the Viewer feature. See pages 64.
NOTE: When the projector displays a blue or a black screen, the Eco mode will be automatically selected in "Lamp Mode."
92
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Using On-Screen Menu
Setup [Page3]
Selecting Signal Format [Signal Select]
Computer 1/2
Allows you to set "Computer 1" and "Computer 2" to automatically detect an incoming RGB or component source
such as a computer or DVD player. However there may be some RGB and component signals that the projector is
unable to detect. In this case, select "RGB" or "Component".
Select "Scart" in COMPUTER 2 for the European Scart signal.
Component
Normally select "Auto" and the projector automatically detects an incoming signal. However there may be some
component signals that the projector is unable to detect.
If this is the case, select "Component".
NOTE: When using the "Y" connector of the COMPONENT connectors to display a Video signal, select "Video".
Selecting Color System [Color System]
This feature enables you to select composite video standards automatically or manually.
Normally select "Auto" and the projector will automatically detect the video standard.
In the case where the projector has difficulty detecting the video standard, select the appropriate video standard from
the menu.
93
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Using On-Screen Menu
Setting MONITOR OUT Connector [OUT Terminal]
This option allows you to determine which RGB or component source is output from the MONITOR OUT connector
during Idle mode.
Last ....................... The signal from the last COMPUTER1 or 2, or COMPONENT input will be output to the MONITOR OUT
connector.
COMPUTER 1, 2 .... The signal from the COMPUTER1 or 2 input will be output to the MONITOR OUT connector.
COMPONENT ........ The signal from the COMPONENT input will be output to the MONITOR OUT connector.
Selecting S-Video Mode [S-Video Mode Select]
This feature is used to select the S-Video signal detection mode. This allows identifying of the S-Video signals with
different aspect ratio (16:9 and 4:3).
Off ......................... Does not identify any S-video signal.
S2.......................... Identifies the 16:9 or 4:3 signal.
Turning On / Off Source Display and Message [Display Select]
Source
This option turns on or off input name display such as Computer 1/2, Video, and No Input to be displayed in the top
right corner of the screen.
Message
This option turns on and off messages for lamp life warning, 3-minute before power off time, “Please clean filter”
and “Please wait a moment”.
94
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Using On-Screen Menu
Selecting Menu Color [Menu Color Select]
You can choose between two color modes for menu color: color and monochrome.
Setup [Page4]
Enabling Power Management [Power Management]
When this option is on and there is no input for five minutes or more, the projector will automatically turn itself off.
95
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Using On-Screen Menu
Enabling Power Off Confirmation [Power Off Confirmation]
This option determines whether a confirmation dialog for turning off the projector will appear or not.
NOTE: When the confirmation message is displayed, you must be in the Projector mode to operate your projector using the
remote control. If not, press the PJ button on the remote control to change your projector to the Projector mode. The button
lights to indicate that you are in the Projector mode.
Enabling High Speed Fan Mode [Fan Mode]
This option allows you to select two modes for fan speed: Auto mode and High speed mode.
Auto ...................... The built-in fans automatically run at a variable speed according to the internal temperature.
High Speed............ The built-in fans run at a fixed high speed.
When you wish to cool down the temperature inside the projector quickly, select “High Speed”.
NOTE: Select High speed mode if you continue to use the projector for consecutive days.
96
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Using On-Screen Menu
Enabling Standby Mode [Standby Mode]
The projector has two standby modes: Idle mode and Power-saving mode.
Power-saving mode is the mode that allows you to put the projector in the standby condition which consumes less
power than the Idle mode. The projector is preset for Idle mode at the factory.
NOTE:
•
•
The MONITOR OUT function is not available during Power-saving mode.
Control through the PC Control connector is not available during Power-saving mode. For PC control of the projector it is
recommended to leave the projector in Idle mode.
Enabling Auto Start [Auto Start]
Turns the projector on automatically when the power cable is inserted into an active power outlet and the main power
switch is turned on. This eliminates the need to always use the "Power" button on the remote control or projector
cabinet.
[Remote Sensor]
This option determines which remote sensor on the projector is enabled.
Selecting “On” indicates that the selected remote sensor can accept the infrared signal from the supplied remote
control.
97
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Using On-Screen Menu
Setup [Page5]
Resetting the Filter Usage Hours [Filter Usage]
Resets the filter usage back to zero. Pressing the Clear button displays a confirmation dialog box. To reset the filter
usage hours, press "OK".
Clearing Lamp Hour Meter [Lamp Hour]
Resets the lamp clock back to zero. Pressing the Clear button displays a confirmation dialog box. To reset the lamp
usage hour, press "OK".
NOTE: The projector will turn off and go into standby mode after 2100 hours (up to 3100 hours in Eco mode) of service. In this
condition you cannot clear the lamp hour meter on the menu. If this happens, press the "HELP" button on the remote control for
ten seconds to reset the lamp clock back to zero. Do this only after replacing the lamp.
98
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Using On-Screen Menu
Selecting Communication Speed [Communication]
This feature sets the baud rate of the PC Control port (D-Sub 9 Pin). It supports data rates from 4800 to 38400 bps.
The default is 38400 bps. Select the appropriate baud rate for your equipment to be connected (depending on the
equipment, a lower baud rate may be recommended for long cable runs).
Selecting Projecting Pointer Icon [Pointer]
This enables you to select from nine different Pointer icons for the "Pointer" button on your remote control.
After moving your Pointer icon to the area you want on the screen, press the MAGNIFY button on the remote control
to enlarge the selected area on the screen. See page 41 for more details.
NOTE: There may be cases where the Pointer function is not available (ex. A non-interlace signal at 15kHz such as video game.)
Setting Mouse Pointer, Button and Sensitivity [Mouse]
This option lets you to change your USB mouse settings.The mouse settings feature is available for USB mouse only.
Choose the settings you want:
Mouse Pointer ....... Pointer 1 - 9
Mouse Button........ "Right Hand" or "Left Hand"
Mouse Sensitivity .. "Fast", "Medium" or "Slow"
99
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Using On-Screen Menu
ᕧ Menu Descriptions & Functions [Information]
Displays the status of the current signal, the lamp and the projector usage hours. This dialog box has four pages.
The information included are as follows:
[Page 1] Source Name
Input Terminal
Entry No.
Horizontal Frequency
Vertical Frequency
[Page 2] Signal Type
Video Type
Sync Type
Interlace
Sync Polarity
[Page 3] Remaining Lamp Time (%)
Lamp Hour Meter (H)
Filter Usage (H)
Projector Usage (H)
NOTE: The progress indicator shows the percentage of remaining bulb life. The value informs you of the amount of
lamp and projector usage respectively.
[Page 4] Version (BIOS, Firmware, Data)
Remaining Lamp Time Display
When the remaining lamp time reaches 0, the Remaining LampTime bar indicator changes from 0% to 100 Hours and
starts counting down. If the remaining lamp time reaches 0 hours, the projector will not turn on regardless of whether
the lamp mode is set to Normal or Eco.
100
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Using On-Screen Menu
ᕨ Menu Descriptions & Functions [Reset]
Returning to Factory Default
The Reset feature allows you to change adjustments and settings to the factory preset for sources by the following
methods:
Current Signal
Resets the adjustments for the current signal to the factory preset levels.
All the items in “Adjust (except “Wall Color”) and “Image" can be reset.
All Data
Reset all the adjustments and settings for all the signals to the factory preset except Remaining Lamp Time, Lamp
Hour Meter, Filter Usage, Projector Usage, Communication, Language, Background, Entry List, Standby Mode,
Security and Password (Logo).
(To reset the lamp usage time, see “Clear Lamp Hour Meter” on page 98)
All Data (Including Entry List)
Reset all the adjustments and settings for all the signals to the factory preset except Remaining Lamp Time, Lamp
Hour Meter, Filter Usage, Projector Usage, Communication, Language, Background, Entry List, Standby Mode,
Security and Password (Logo).
Also deletes all the signals in the Entry List and returns to the factory preset.
NOTE: Locked signals in Entry List cannot be reset.
101
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Using On-Screen Menu
ᕩ Entry List
Displaying the Entry List
Press the SOURCE button to display the list of the entry signals. Use the SELECT ̆̄ buttons on your remote control
or the projector cabinet to select the signal and press the ENTER button on the remote control or the projector cabinet
to display the Entry Edit Command screen.
Entering the Currently Projected Signal into the Entry List
1. Display the Entry List.
2. Use the SELECT ̆ or ̄ button on your remote control or the projector cabinet to select any number and
press the ENTER button on the remote control or the projector cabinet to display the Entry Edit Com-
mand screen.
3. Use the SELECT ̇ or ̈ button to select "Store" and press the ENTER button.
Using the Entry List
Making any adjustments to the current picture will automatically register its adjustments to the Entry List. The regis-
tered signal can be loaded any time from the Entry List.
NOTE: Up to 100 presets can be registered except settings on the Picture.
102
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Using On-Screen Menu
Entry Edit Command
You can edit signals on the Entry List.
Load ...................... Enables you to select a signal from the list.
Store ..................... Enables you to store the currently projected signal.
Cut ........................ Enables you to remove a selected signal from the list and place it on the "clipboard" in the projector.
Copy ...................... Enables you to copy a selected signal from the list and place it on the "clipboard" in the projector.
Paste ..................... Enables you to paste the signal placed on the "clipboard" to any other line of the list. To do this, select "Paste"
and then select the line number you want to paste to. Last press ENTER.
Edit ........................ Enables you to change source names.
Source Name:
Enter a signal name. Up to 18 alphanumeric characters can be used.
Input Terminal:
Change the input terminal. Video and S-Video are available for composite signal. Component and Computer
are available for component signal.
Lock:
Set so that the selected signal cannot be deleted when "All Delete" is executed.
Skip:
Set so that the selected signal will be skipped during auto search.
When complete, select OK and press ENTER. To exit without storing setting, select Cancel. Select "Source
Name" and press ENTER to display the Source Name Edit window. You can change source name on this
window. Press ̄ to display the software keyboard, which you can enter alphanumeric characters. See page
120 for the key function of the software keyboard.
All Delete ............... This feature enables you to delete all the registered signals in the Entry List.
The following buttons are not available for the currently projecting signals:
1) The Cut and Paste buttons on the Entry Edit Command screen
2) The Input Terminal button on the Entry Edit screen
NOTE: When all the signals in the Entry List are deleted, the currently projected signal will be also deleted except locked signals.
103
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Maintenance
ᕡ Cleaning the Filters................................................. 105
ᕢ Cleaning the Cabinet .............................................. 105
ᕣ Cleaning the Lens................................................... 106
ᕤ Replacing the Lamp and Filters.............................. 107
104
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Maintenance
This section describes the simple maintenance procedures you should follow to clean the filter and replace the lamp.
ᕡ Cleaning the Filters
The air-filter sponge keeps dust and dirt from getting inside the projector and should be cleaned after every 100 hours
of operation (more often in dusty conditions). If the filters are dirty or clogged, your projector may overheat.
CAUTION
•
•
Turn off the projector, turn off the main power switch and unplug the projector before cleaning the filters.
Only clean the outside of the filter cover with a vacuum cleaner.
1. Vacuum the filter from the outside.
R
E
O W
T U S
T A
L A M
P
P
Y
S
D
B
T A N
N / S
O
T
S
J U
M
D
R
A
T O
E F O
R
A U
3 D
E
C
D
U R
A R
C
S O
P C
L
E C
N
A
C
R
E
T
T
N
S E L E C
U
N
E
M
ZOOM
F
O
C
U
S
2. Reset the filter usage time.
To reset the filter usage time, from the menu, select [Setup] → [Page 5] → [Filter Usage] → [Clear Filter Usage Meter]
and then press “Clear”.
See also page 98 for resetting the filter usage time.
ᕢ Cleaning the Cabinet
CAUTION
Turn off the projector, turn off the main power switch and unplug the projector before cleaning the cabinet.
S
U
C
O
F
ZOOM
r
LAMP
STATUS
POWER
ST
ADJU
b
T
Y
N
E
AUTO
N
IO
R
R
O
C
BY
P
M
O
C
/STAND
N
O
O
SOURCE
ON
/M
L
U
N
E
M
3D REFORM
O
O
E
N
IO
ID
D
U
-V
S
L
/M
A
A
E
SELECT
C
O
E
N
ID
V
A
C
1
2
USB(MOUSE)
R
E
T
P
M
O
C
R
E
E
N
T
PC CARD
IO
D
U
USB(COMPUT
IO
D
D
R
U
A
A
C
C
P
R
E
T
U
P
T
U
M
O
R
C
O
IT
N
O
M
L
O
R
T
N
O
C
C
P
IN
C
A
Clean the cabinet periodically with a damp cloth. If heavily soiled, use a mild detergent. Never use strong
detergents or solvents such as alcohol or thinner.
105
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Maintenance
ᕣ Cleaning the Lens
CAUTION
Turn off the projector, turn off the main power switch and unplug the projector before cleaning lens.
P O W E R
S T A T U S
L A M P
O N / S T A N D B Y
A U T O A D J U S T
3 D R E F O R M
S O U R C E
P C C A R D
L
E C
N
A
C
R
E
T
T
C
E
N
L
E
S
U
N
E
M
Z
O
O
M
FOCUS
Use a blower or lens paper to clean the lens, and be careful not to scratch the lens.
106
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Maintenance
ᕤ Replacing the Lamp and Filters
After your lamp has been operating for 2000 hours (up to 3000 hours in Eco mode) or longer, the LAMP indicator in the
cabinet will blink red and the message will appear. Even though the lamp may still be working, replace it at 2000 (up to
3000 hours in Eco mode) hours to maintain optimal projector performance.
CAUTION
•
DO NOT TOUCH THE LAMP immediately after it has been used.
It will be extremely hot. Turn the projector off, wait 10 seconds, turn off the main power switch and then discon-
nect the power cable. Allow at least one hour for the lamp to cool before handling.
•
•
DO NOT REMOVE ANY SCREWS except the lamp cover screw and two lamp case screws.You could receive
an electric shock.
The projector will turn off and go into stand by mode after 2100 (up to 3100 hours in Eco mode) hours of
service. If this happens, be sure to replace the lamp. If you continue to use the lamp after 2000 hours (up to
3000 hours in Eco mode) of use, the lamp bulb may shatter, and pieces of glass may be scattered in the lamp
case. Do not touch them as the pieces of glass may cause injury. If this happens, contact your dealer for
lamp replacement.
To replace the lamp:
1. Loosen the lamp cover screw until the screwdriver goes into a free-wheeling condition and remove the
lamp cover.The lamp cover screw is not removable.
Catch
D
D
J
U
JUST
S
T
LAMP
LAMP
STATUS
S
TATUS
W
W
ER
ER
1
2
COMPONENT
COMPONENT
Y
R
R
1
2
ER
ER
1
2
Cb/
Cb/
AUDIO
S-VIDEO
AUDIO
S-VIDEO
Cr/P
Cr/P
/ONAOUDI
L/MONAOUDIO
L/ONAOUDIO
L/MONAOUDIO
AUDIO
AUDIO
VIDEO
R
R
VIDEO
R
R
2. Loosen the two screws securing the lamp housing until the screw-driver goes into a freewheeling
condition.The two screws are not removable.
Remove the lamp housing by pulling out the handle.
NOTE: There is an interlock on this case to prevent the risk of electrical shock. Do not attempt to circumvent this interlock.
Interlock
D
JU
D
S
JUST
L
T
L
A
S
M
P
T
A
M
A
S
T
T
P
U
A
W
S
T
E
U
S
R
W
E
R
C
O
M
C
P
O
M
O
N
P
E
O
N
N
T
E
N
T
E
R
Y
C
1
2
E
R
1
2
b
/P
b
/P
A
A
U
D
C
r/P
A
A
IO
U
D
IO
C
r
/P
S
r
-V
ID
S
E
-V
ID
R
O
E
E
O
R
L
A
U
/M
O
O
D
L
A
O
N
I
/M
U
O
U
O
O
D
D
N
I
IO
U
D
V
IO
ID
R
R
E
V
ID
O
R
R
E
O
L
A
U
O
/M
D
L
A
O
I
N
/M
U
D
N
107
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Maintenance
3. Insert a new lamp housing until the lamp housing is plugged into the socket.
CAUTION
Do not use a lamp other than the authorized replacement lamp.
Order this from your dealer.
Secure it in place with the two screws.
Be sure to tighten the screws.
J
U
D
S
T
JUST
L
A
S
M
P
T
LAMP
STATUS
A
T
U
S
W
O
E
R
WER
COMPO
AUDIO
COMPONENT
NENT
R
R
1
2
Y
ER
1
2
Cb/P
Cb/P
Cr/P
AUDIO
S-VIDEO
Cr/P
S-VIDEO
ER
L
/
M
A
U
D
I
O
ON
O
/ONAOUDIO
L/ONAOUDI
AUDIO
AUDIO
VID
EO
R
R
VIDEO
R
R
L
/
M
A
U
D
ON
I
O
4. Reattach the lamp cover.
Tighten the lamp cover screw.
Be sure to tighten the screw.
Allow about 0.4"
(1 cm) of space.
J
D
JUST
UST
LA
L
A
S
M
P
S
M
P
TA
T
A
T
T
U
S
U
W
W
S
ER
E
R
C
C
O
M
O
M
P
P
O
N
O
N
E
N
E
N
T
T
Y
C
Y
E
R
R
R
1
2
1
2
C
b
/
b
/P
A
A
A
A
U
U
D
D
IO
C
r/P
IO
C
r/P
r
S
S
-V
ID
-V
ID
E
O
E
E
R
O
L
/M
A
U
L
A
O
/M
U
O
D
O
O
D
N
O
N
I
U
U
D
D
IO
IO
V
V
ID
R
R
ID
R
R
E
E
O
O
L
A
U
L
A
O
/M
/M
U
D
D
O
I
N
O
N
5. After you install a new lamp, select the menu → [Setup] → [Page 5] → [Lamp Hour] → [Clear Lamp Hour
Meter], and then press “Clear” to clear the lamp usage hours.
NOTE: When the lamp exceeds 2100 hours (up to 3100 hours in Eco mode) of service, the projector cannot turn on and the menu
is not displayed. If this happens, press the Help button on the remote control for a minimum of 10 seconds while in standby
mode. When the lamp time clock is reset to zero, the LAMP indicator goes out.
108
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Maintenance
Replacing the Filters
NOTE: Do not wash the filter with soap and water. Soap and water will damage the filter membrane. Before replacing the filter,
remove dust and dirt from the projector cabinet. Keep out dust and dirt during filter replacement.
NOTE: When you replace the lamp, it is also wise to replace the filters. The filters come in the same package with your replace-
ment lamp.
CAUTION
•Turn off the projector, turn off the main power switch and unplug the projector before replacing the filters.
• Do not attempt to operate the projector without the two filter covers.
To replace the filters (sponge)
1. Remove the filter by pushing on the catch and pull it.
Catch
2. Gently peel off the filter (sponge) and replace it with the new one.
3. Reinstall the new filter cover.
The two filter covers are interchangeable.
To reset the filter usage time, from the menu, select [Setup] → [Page 5] → [Filter Usage] → [Clear Filter Usage Meter].
See also page 98 for resetting the filter usage time.
109
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Appendix
ᕡ Troubleshooting ...................................................... 111
ᕢ Specifications ......................................................... 114
ᕣ Cabinet Dimensions ............................................... 116
ᕤ Pin Assignments of D-Sub COMPUTER 1/2 Input
Connector............................................................. 117
ᕥ Compatible Input Signal List ................................... 118
ᕦ PC Control Codes and Cable Connection .............. 119
ᕧ Using Software Keyboard ....................................... 120
110
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Appendix
ᕡ Troubleshooting
This section helps you resolve problems you may encounter while setting up or using the projector.
Indicator Messages
Power Indicator
Indicator Condition
Projector Condition
The main power is off
The projector is getting ready to turn on. Wait for a moment.
Note
Off
–
Blinking light
Steady light
Green
0.5 sec On,
0.5 sec Off
0.5 sec On,
0.5 sec Off
Orange
The projector is cooling down.
Wait for a moment.
Green
The projector is turned on.
–
–
Orange
The projector is in Power-saving or Idle.
Status Indicator
Indicator Condition
Off
Projector Condition
Note
Normal
–
Blinking light
Red
1 cycle (0.5 sec On, Lamp cover error
2.5 sec Off)
Replace the lamp cover correctly.
2 cycle (0.5 sec On, Temperature error
0.5 sec Of)
The projector is overheated. Move
the projector to a cooler location.
Power unit will not work correctly.
3 cycle (0.5 sec On, Power error
0.5 sec Off)
4 cycle (0.5 sec On, Fan error
0.5 sec Off)
Fans will not work correctly.
6 cycle (0.5 sec On, Lamp error
0.5 sec Off)
Lamp fails to light. Wait a full
minute and then turn on again.
The projector is re-firing.
You have pressed cabinet button
when Cabinet Button is locked.
–
Green
Re-firing the lamp
Steady light
Orange
Cabinet button is locked
Green
Idle condition
Lamp Indicator
Indicator Condition
Projector Condition
Note
Off
Normal
–
Red
Blinking light
Steady light
Lamp has reached its end of life. Lamp Replace the lamp.
replacement message will be displayed.
Lamp has been used beyond its limit. The Replace the lamp.
projector will not turn on until the lamp is
replaced.
Red
Green
Lamp mode is set to Eco mode
–
111
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Appendix
Common Problems & Solutions (See also "Power/Status/Lamp Indicator" on page 111.)
Problem
CheckThese Items
Does not turn on
•
Check that the power cable is plugged in and that the power button on the projector cabinet or the remote
control is on. See pages 28 and 30.
•
•
Ensure that the lamp cover is installed correctly. See page 108.
Check to see if the projector has overheated or the lamp usage exceeds 2100 hours (up to 3100 hours : Eco
mode). If there is insufficient ventilation around the projector or if the room where you’re presenting is par-
ticularly warm, move the projector to a cooler location.
The lamp may fail to light. Wait a full minute and then turn on the power again.
The lamp has reached the end of its usable life. Replace the lamp.
•
•
Will turn off
No picture
•
•
Ensure that the Power Management is off. See page 95.
Use the SOURCE button on the projector cabinet or the VIDEO, the S-VIDEO, the COMPONENT, the COM-
PUTER 1/2 or the VIEWER button on the remote control to select your source (Computer 1/2, Component,
Video, S-Video or Viewer). See page 32.
•
•
•
•
•
•
Ensure your cables are connected properly.
Use menus to adjust the brightness and contrast. See page 78.
Remove the lens cap.
Reset the settings or adjustments to factory preset levels using the Reset in the Menu. See page 101.
Enter your registered keyword if the Security function is enabled. See page 49.
When using with a notebook PC, be sure to connect between the projector and the notebook PC before turning
on the power to the notebook PC. In most cases signal cannot be output from RGB output unless the notebook
PC is turned on after connecting with the projector.
* If the screen goes blank while using your remote control, it may be the result of the computer's screen-
saver or power management software.
* If you accidentally hit the POWER button on the remote control, wait 60 seconds and then press the POWER
button again to resume.
•
•
See also the next page.
Picture suddenly
becomes dark
When one of the following happens, the Lamp mode automatically changes from Normal to Eco.
* When there are no signals (blue or black screen) → To return to the Normal mode, select another available
source.
* When the image is muted using the PIC-MUTE button on the remote control → Press the PIC-MUTE button
again to return to the Normal mode.
* When the room where you' re presenting is particularly warm → Move the projector to a cooler location.
Color tone or hue is
unusual
•
•
Check if an appropriate color is selected in "Wall Color". If so, select an appropriate option. See page 80.
Adjust "Hue" in "Picture". See page 78.
Image isn’t square to
the screen
•
•
Reposition the projector to improve its angle to the screen. See page 33.
Use the 3DReform function to correct the trapezoid distortion. See page 35.
Picture is blurred
•
•
•
Adjust the focus. See page 34.
Reposition the projector to improve its angle to the screen. See page 33.
Ensure that the distance between the projector and screen is within the adjustment range of the lens. See page
22.
•
•
•
Condensation may form on the lens if the projector is cold, brought into a warm place and is then turned on.
Should this happen, let the projector stand until there is no condensation on the lens.
Image is scrolling
vertically, horizontally
or both
Use the SOURCE button on the projector cabinet or the VIDEO, the S-VIDEO, the COMPONENT, the COM-
PUTER 1/2 or the VIEWER button on the remote control to select your source (Video, S-Video, Component,
Computer or Viewer). See page 32.
Adjust the computer image manually with the Pixel Adjust/Position in the Image. See page 84.
Remote control does
not work
•
•
•
•
Install new batteries. See page 19.
Make sure there are no obstacles between you and the projector.
Stand within 22 feet (7 m) of the projector. See page 19.
Check if one or more remote sensors are enabled. Select [Setup] → [Page 4] → [Remote Sensor] from the
menu. See page 97.
•
Make sure that you are in the Projector mode and the PJ button lights in red. If not, press the PJ button. See
page 40.
Indicator is lit or
blinking
•
See the POWER/STATUS/LAMP Indicator on page 111.
Cross color in RGB
mode
•
•
Press the AUTO ADJUST button on the projector cabinet or the AUTO ADJ. button on the remote control. See
page 37.
Adjust the computer image manually with the Pixel Adjust/Position in the Image. See page 84.
For more information contact your dealer.
112
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Appendix
If there is no picture, or the picture is not displayed correctly.
•
Power on process for the projector and the PC.
Be sure to connect the RGB cable between the projector and the computer before turning on the computer.
There are some notebook PCs, which do not output signal unless there is a projectors or monitor connected
first.
NOTE: You can check the horizontal frequency of the current signal in the projector’s menu under ‘Menu → Help → Informa-
tion. If it reads “0kHz”, this means there is no signal being output from the computer. See page 100 or go to next step.
•
Enabling the computer’s external display.
Displaying an image on the notebook PC’s screen does not necessarily mean it outputs a signal to the projec-
tor. When using a PC compatible laptop, a combination of function keys will enable/disable the external display.
Usually, the combination of the ‘Fn” key along with one of the 12 function keys gets the external display to come
on or off. For example, laptops use Fn + F3, while Dell laptops use Fn + F8 key combinations to toggle
through external display selections.
•
•
Non-standard signal output from the computer
If the output signal from a notebook PC is not an industry standard, the projected image may not be displayed
correctly. Should this happen, deactivate the notebook PC’s LCD screen when the projector display is in use.
Each notebook PC has a different way of deactivate/reactivate the local LCD screens as described in the
previous step. Refer to your computer’s documentation for detailed information.
Image displayed is incorrect when using a Macintosh
When using a Macintosh with the projector, set the DIPswitch of the Mac adapter (not supplied with the projec-
tor) according to your resolution. After setting, restart your Macintosh for the changes to take affect.
For setting display modes other than those supported by your Macintosh and the projector, changing the DIP
switch on a Mac adapter may bounce an image slightly or may display nothing. Should this happen, set the DIP
switch to the 13” fixed mode and then restart your Macintosh. After that, restore the DIP switches to a
displayable mode and then restart the Macintosh again.
NOTE: A Video Adapter cable manufactured by Apple Computer is needed for a PowerBook which does not have a mini D-Sub
15-pin connector.
•
•
Mirroring on a PowerBook
*
When using the projector with a Macintosh PowerBook, output may not be set to 1024 x 768 unless “mirror-
ing” is off on your PowerBook. Refer to owner’s manual supplied with your Macintosh computer for mirroring.
Folders or icons are hidden on the Macintosh screen
Folders or icons may not be seen on the screen. Should this happen, select [View] ->[Arrange] from the Apple
menu and arrange icons.
113
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Appendix
ᕢ Specifications
Model Number
8768
Optical
LCD Panel
Resolution
Lens
0.8" p-Si TFT active-matrix with Micro Lens Array
1024 ꢀ 768 pixels* native, up to UXGA with Advanced AccuBlend
Manual zoom and focus:
F1.7 - 2.0
f=24.0 - 28.8mm
Lamp
200W (152W Eco mode)
Image Size
Projection Distance
Projection Angle
25 - 300 inches (0.6 - 7.6 m) diagonal
2.38 - 35.8 ft / 0.7 (Wide) - 11 m (Tele)
Tele : 9.5° - 9.9° Wide : 11.4° - 12.1°
Electrical
Inputs
2 RGB (D-Sub 15 Pin), 1 Component (RCAꢀ3 [YCbCr]),
1 S-Video (DIN 4 Pin), 1 Video (RCA), 2 Stereo Mini Audio,
2 (L/R) RCA Audio, 1 PC Control (D-Sub 9 Pin)
1 RGB (D-Sub 15 Pin), 1 Stereo Mini Audio
1 A Type, 1 B Type
Outputs
USB Port
PC Card
1 Slot
Video Compatibility
NTSC, NTSC4.43, PAL, PAL-60, PAL-N, PAL-M, SECAM, HDTV:1080i,
1080i/50Hz, 720p, 576p, 480p, 480i, 576i/50Hz
Horizontal: 15 kHz to 100 kHz (RGB: 24 kHz or over)
Vertical: 50 Hz to 120 Hz
Scan Rate
Video Bandwidth
RGB: 80 MHz (-3dB)
Color Reproduction
Horizontal Resolution
16.7 million colors simultaneously, Full color
NTSC / NTSC4.43/PAL/PAL-M/PAL-N/PAL60: 540 TV lines
SECAM: 300 TV lines
RGB: 1024 dots (H) ꢀ 768 dots (V)
RS232, IR
Separate Sync / Composite Sync / Sync on G
5W ꢀ 2
100 - 240V AC, 50 / 60 Hz
3.2A (100 - 240V AC)
External Control
Sync Compatibility
Built-in Speaker
Power Requirement
Input Current
Power Consumption
9W in Idle mode / 6W in Power-saving mode /
280W in Lamp Normal mode /
225W in Lamp Eco mode
114
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Appendix
Mechanical
Installation Orientation
Dimensions
Desktop/Front, Desktop/Rear, Ceiling/Front, Ceiling/Rear
13.4" (W) ꢀ 3.8" (H) ꢀ 9.6" (D)
340mm (W) ꢀ 97mm (H) ꢀ 245mm (D)
(not including protrusions)
Net Weight
7.9 lbs / 3.6 kg
Environmental Considerations Operational Temperatures : 32° to 95°F (0° to 35°C),
20% to 80% humidity (non-condensing)
Storage Temperatures :14° to 122°F (-10° to 50°C), 20% to 80% humidity
(non-condensing)
Regulations
UL Approved (UL 60950, CSA 60950)
Meets DOC Canada Class B requirements
Meets FCC Class B requirements
Meets AS/NZS Cispr. 22: Class B
Meets EMC Directive (EN55022, EN55024, EN61000-3-2,
EN61000-3-3)
Meets Low Voltage Directive (EN60950, TUV GS Approved)
* Effective pixels are more than 99.99%.
The specifications are subject to change without notice.
115
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Appendix
ᕣ Cabinet Dimensions
A U D I O
C O M P U T E R
C O M P U T E R
2
1
P C C O N T R O L
R
R
L / M O N O V I D E O
L / M O N O
A U D I O
S - V I D E O
A U D I O
A U D I O
M O N I T O R O U T
U S B ( C O M P U T E R )
A U D I O
r / P C r
b / P b
Y
C
U S B ( M O U S E )
P C C A R D
C O M P O N E N T
107 (4.2")
97 (3.8")
P C C A R D
O N / S T A N D B Y 3 D R E F O R M
A U T O A D J U S T S O U R C E
P O W E R
S T A T U S
L A M P
S E L E C T
Z O O M
F O C U S
340 (13.4")
Lens center
83 (3.27")
Lens center
Unit: mm (inch)
116
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Appendix
ᕤ Pin Assignments of D-Sub COMPUTER 1/2 Input Connector
Mini D-Sub 15 Pin Connector
Pin No. RGB Signal (Analog)
5
4
3
2
1
1
2
3
Red
10
9
8
7
6
Green or Sync on Green
Blue
15 14 13 12 11
4
5
6
7
Ground
Ground
Red Ground
Green Ground
Blue Ground
Signal Level
Video signal : 0.7Vp-p (Analog)
Sync signal : TTL level
8
9
No Connection
Sync Signal Ground
SCART Sync*1
Bi-directional DATA (SDA)*2
Horizontal Sync or Composite Sync
Vertical Sync
10
11
12
13
14
15
Data Clock
*1 COMPUTER 2 input only
*2 COMPUTER 1 input only
117
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Appendix
ᕥ Compatible Input Signal List
Signal
Resolution
Frequency H.
( kHz )
15.734
15.625
15.734
15.625
31.47
31.47
31.47
34.97
35
Refresh Rate
( Hz )
60
50
60
50
59.94
60
60
66.67
66.67
72.81
75
75
85.01
70.09
85.04
87.85
87.85
56.25
60.32
72.19
75
85.06
74.55
43 Interlaced
60
70.07
74.93
75.03
85
75
75.06
65.95
76.05
60
60.02
65.18
72.01
76.11
75.03
85.02
–
60 Progressive
50
50
60 Interlaced
50 Interlaced
60 Progressive
59.94 Progressive
60
65
70
75
( Dots )
NTSC
PAL
PAL60
SECAM
VESA
IBM
MAC
MAC
MAC
VESA
VESA
IBM
VESA
IBM
VESA
IBM
IBM
VESA
VESA
VESA
VESA
VESA
MAC
VESA
VESA
VESA
MAC
VESA
VESA
VESA
MAC
SUN
SGI
VESA
VESA
MAC
HP
SUN
VESA
VESA
SXGA+
HDTV (1080p)
SDTV(576i)(625i)
SDTV(576p)(625p)
–
–
–
–
640 ꢀ 480
640 ꢀ 480
640 ꢀ 480
640 ꢀ 480
640 ꢀ 480
640 ꢀ 480
640 ꢀ 480
640 ꢀ 480
640 ꢀ 480
720 ꢀ 350
720 ꢀ 400
720 ꢀ 350
720 ꢀ 400
800 ꢀ 600
800 ꢀ 600
800 ꢀ 600
800 ꢀ 600
800 ꢀ 600
832 ꢀ 624
1024 ꢀ 768
1024 ꢀ 768
1024 ꢀ 768
1024 ꢀ 768
1024 ꢀ 768
1024 ꢀ 768
1152 ꢀ 864
1152 ꢀ 870
1152 ꢀ 900
1152 ꢀ 900
1280 ꢀ 960
1280 ꢀ 1024
1280 ꢀ 1024
1280 ꢀ 1024
1280 ꢀ 1024
1280 ꢀ 1024
1280 ꢀ 1024
1400 ꢀ 1050
1920 ꢀ 1080
–
37.86
37.5
39.375
43.269
31.469
37.927
39.44
39.44
35.16
37.879
48.077
46.88
53.674
49.725
35.5
48.363
56.476
60.241
60.023
68.677
67.5
68.681
61.796
71.736
60
63.981
69.89
78.125
81.13
79.976
91.146
–
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
67.5
15.6
31.5
–
HDTV (1080i)(1125i) 1920 ꢀ 1080
HDTV (1080i)(1125i) 1920 ꢀ 1080
HDTV (720p)(750p) 1280 ꢀ 720
33.75
28.125
45
31.47
75.0
81.25
87.5
93.75
15.734
15.625
SDTV (480p)(525p)
VESA
VESA
VESA
VESA
–
1600 ꢀ 1200
1600 ꢀ 1200
1600 ꢀ 1200
1600 ꢀ 1200
–
DVD YCbCr
DVD YCbCr
59.94 Interlaced
50 Interlaced
–
#: Images in above flagged with # are compressed with Advanced AccuBlend.
NOTE: Some composite sync signals may not be displayed correctly.
Signals other than those specified in the table above may not be displayed correctly. If this should happen, change the refresh
rate or resolution on your PC. Refer to Display Properties help section of your PC for procedures.
UXGA (1600 ꢀ 1200) is supported for separate sync signal only.
118
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Appendix
ᕦ PC Control Codes and Cable Connection
PC Control Codes
Function
Code Data
POWER ON
02H
02H
02H
02H
02H
02H
02H
02H
02H
02H
02H
02H
02H
02H
00H
00H
00H
00H
00H
00H
00H
00H
00H
00H
00H
00H
00H
00H
00H
00H
00H
00H
00H
00H
00H
00H
00H
00H
00H
00H
00H
00H
00H
00H
00H
02H
02H
02H
02H
02H
02H
00H
00H
00H
00H
00H
00H
02H
03H
01H
01H
01H
01H
01H
01H
12H
13H
14H
15H
16H
17H
POWER OFF
01H
03H
03H
03H
03H
03H
03H
10H
11H
12H
13H
14H
15H
INPUT SELECT COMPUTER 1
INPUT SELECT COMPUTER 2
INPUT SELECT VIDEO
INPUT SELECT S-VIDEO
INPUT COMPONENT
INPUT SELECT VIEWER
PICTURE MUTE ON
PICTURE MUTE OFF
SOUND MUTE ON
01H
02H
06H
0BH
1AH
1FH
09H
0AH
0EH
13H
22H
27H
SOUND MUTE OFF
ON SCREEN MUTE ON
ON SCREEN MUTE OFF
NOTE: Contact your local dealer for a full list of PC Control Codes if needed.
Cable Connection
Communication Protocol
Baud rate ........................................ 38400 bps
Data length ..................................... 8 bits
Parity.............................................. No parity
Stop bit .......................................... One bit
X on/off .......................................... None
Communications procedure ........... Full duplex
NOTE: Depending on the equipment, a lower baud rate may be recommended for long cable runs.
PC Control Connector (D-SUB 9P)
To TxD of PC
To RxD of PC
To GND of PC
1
2
3
4
5
6
7
8
9
NOTE: Pins 1, 4, 6 and 9 are no used.
To RTS of PC
To CTS of PC
NOTE: Jumper “Request to Send” and “Clear to Send”
together on both ends of the cable to simplify cable
connection.
119
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Appendix
ᕧ Using Software Keyboard
1 to 0 and Characters
.............................. Use to type in password or keyword.
MODE .................... Selects one of three modes for alphabet and special characters.
SP ......................... Inserts a space
BS ......................... Deletes one character backward
̇ .......................... Returns to the previous
̈ .......................... Advances to the next
OK ......................... Executes the selection
Cancel ................... Cancels the selection
NOTE: You can drag the Software keyboard on the screen by clicking and holding any part on the keyboard except buttons.
120
Download from Www.Somanuals.com. All Manuals Search And Download.
DUKANE CORPORATION
TWO-YEAR LIMITED WARRANTY
This Dukane projector is warranted to the original purchaser for a period of two (2) years from
the original purchase date – in normal operating conditions – against defects in material and
workmanship . DUKANE CORPORATION EXPRESSLY DISCLAIMS ALL OTHER
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
DURING THE WARRANTY PERIOD, DUKANE CORPORATION’S LIABILITY FOR ANY
DEFECTIVE PRODUCT (except for the lamp, which is subject to whatever warranties the
manufacturer may provide) IS LIMITED TO THE REPAIR OR REPLACEMENT OF
PRODUCT AT DUKANE CORPORATION’S OPTION. REPLACEMENT PRODUCTS MAY
BE NEW OR USED (used units will not exceed hours of defective unit). The following are not
covered by the limited warranty and Dukane Corporation shall not be liable for:
1. Any product which is not distributed in the U.S.A. or Canada by Dukane Corporation or an
authorized dealer.
2. Normal decrease in lamp light output over time.
3. Damage, deterioration or malfunction resulting from:
·
Accident, misuse, abuse, neglect, improper ventilation, fire, dust, smoke, water, lighting
or other acts of nature, unauthorized product modification, or failure to follow
instructions supplied with the product (including proper maintenance of air filters).
Repair or attempted repair by anyone other than a Dukane Corporation authorized service
center.
·
·
·
·
·
Any shipment of product (claims must be presented to the carrier).
Removal or installation of the product.
Any other causes which do not relate to a product defect.
Use of the product beyond normal operating conditions. Normal operating conditions are
defined as product use not in excess of 8 hours per day and 260 days per year.
4. Cartons, carry cases, shipping cases, batteries, or any accessories used in connection with the
product.
5. Service required as a result of third party components.
6. Product used as commercial rental units
Dukane corporation will pay labor and material expenses for covered items, but Dukane
Corporation will not pay for the following:
1. Removal or installation charges.
2. Cost of technical adjustment, set-up, maintenance, or adjustment of user controls.
3. Payment of shipping and related charges incurred in returning the product for warranty
repair.
Dukane Corporation disclaims all liability for incidental or consequential damage of any kind,
including all damages arising out of any interruptions in operation of the product and all damages
to software.
No person, firm, or representative is authorized to assume any obligation or to make any warranty
on behalf of the Dukane Corporation other than as stated above.
11595-B-04
Download from Www.Somanuals.com. All Manuals Search And Download.
Audio Visual Products
Dukane Corporation
Audio Visual Products Division
2900 Dukane Drive
St. Charles, IL 60174-3395
E-mail: [email protected]
Phone: (630) 762-4040
Orders: (800) 676-2485
Information: (800) 676-2486
Fax: (630) 584-5156
Parts & Service: (800) 676-2487
Fax: (630) 584-0984
401-8768-00
Download from Www.Somanuals.com. All Manuals Search And Download.
|