Dukane Projector 8070 User Manual

Portable LCD Projector

Models 8767A, 8771, 8070

User's Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

Important Information

Safety Cautions

Precautions

Please read this manual carefully before using your Dukane Projector and keep the manual

handy for future reference.Your serial number is located on the bottom of your projector.

CAUTION

To turn off main power, be sure to remove the plug from power outlet.

The power outlet socket should be installed as near to the equipment as possible, and should be easily

accessible.

CAUTION

TO PREVENT SHOCK, DO NOT OPEN THE CABINET.

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED NEC SERVICE PERSONNEL.

This symbol warns the user that uninsulated voltage within the unit may be sufficient to cause electrical

shock. Therefore, it is dangerous to make any kind of contact with any part inside of the unit.

This symbol alerts the user that important information concerning the operation and maintenance of this

unit has been provided.

The information should be read carefully to avoid problems.

WARNING: TO PREVENT FIRE OR SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

DO NOT USETHIS UNIT’S PLUG WITH AN EXTENSION CORD OR IN AN OUTLET UNLESS ALLTHE PRONGS

CAN BE FULLY INSERTED.

DO NOT OPEN THE CABINET. THERE ARE HIGH-VOLTAGE COMPONENTS INSIDE. ALL SERVICING MUST

BE DONE BY QUALIFIED NEC SERVICE PERSONNEL.

DOC Compliance Notice (for Canada only)

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.

Acoustic Noise Information Ordinance-3. GSGV (for Germany only):

The sound pressure level is less than 70 dB (A) according to ISO 3744 or ISO 7779.

CAUTION

• Avoid displaying stationary images for a prolonged period of time.

Doing so can result in these images being temporarily sustained on the surface of the LCD panel.

If this should happen, continue to use your projector. The static background from previous images will disap-

pear.

WARNING TO CALIFORNIA RESIDENTS:

Handling the cables supplied with this product, will expose you to lead, a chemical known to the State of California

to cause birth defects or other reproductive harm. Wash hands after handling.

Download from Www.Somanuals.com. All Manuals Search And Download.

Important Information

RF Interference (for USA only)

WARNING

The Federal Communications Commission does not allow any modifications or changes to the unit EXCEPT those

specified by NEC Soluctions (America), Inc. in this manual. Failure to comply with this government regulation could

void your right to operate this equipment.This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates, uses, and can radi-

ate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that interference will not occur in a particular

installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio / TV technician for help.

For UK only: In UK, a BS approved power cable with moulded plug has a Black (five Amps) fuse installed for use with

this equipment. If a power cable is not supplied with this equipment please contact your supplier.

Important Safeguards

These safety instructions are to ensure the long life of your projector and to prevent fire and shock. Please read them

carefully and heed all warnings.

Installation

1. For best results, use your projector in a darkened room.

2. Place the projector on a flat, level surface in a dry area away from dust and moisture.

3. Do not place your projector in direct sunlight, near heaters or heat radiating appliances.

4. Exposure to direct sunlight, smoke or steam can harm internal components.

5. Handle your projector carefully. Dropping or jarring can damage internal components.

6. Do not place heavy objects on top of the projector.

7. If you wish to have the projector installed on the ceiling:

a. Do not attempt to install the projector yourself.

b. The projector must be installed by qualified technicians in order to ensure proper operation and reduce the

risk of bodily injury.

c. In addition, the ceiling must be strong enough to support the projector and the installation must be in accor-

dance with any local building codes.

d. Please consult your dealer for more information.

Download from Www.Somanuals.com. All Manuals Search And Download.

Important Information

Fire and Shock Precautions

1. Ensure that there is sufficient ventilation and that vents are unobstructed to prevent the build-up of heat inside

your projector. Allow at least 3 inches (10 cm) of space between your projector and a wall.

2. Prevent foreign objects such as paper clips and bits of paper from falling into your projector.

Do not attempt to retrieve any objects that might fall into your projector. Do not insert any metal objects such as

a wire or screwdriver into your projector. If something should fall into your projector, disconnect it immediately

and have the object removed by a qualified Dukane service personnel.

3. Do not place any liquids on top of your projector.

4. Do not look into the lens while the projector is on. Serious damage to your eyes could result.

5. Keep any items such as magnifying glass out of the light path of the projector. The light being projected from the

lens is extensive, therefore any kind of abnormal objects that can redirect light coming out of the lens, can

cause unpredictable outcome such as fire or injury to the eyes.

6. Do not cover the lens with the supplied lens cap or equivalent while the projector is on. Doing so can lead to

melting of the cap and possibly burning your hands due to the heat emitted from the light output.

7. The projector is designed to operate on a power supply of 100-240V AC 50/60 Hz. Ensure that your power

supply fits this requirement before attempting to use your projector.

8. Handle the power cable carefully and avoid excessive bending.

A damaged cord can cause electric shock or fire.

9. If the projector is not to be used for an extended period of time, disconnect the plug from the power outlet.

10. Do not touch the power plug during a thunderstorm. Doing so can cause electrical shock or fire.

11. Do not handle the power plug with wet hands.

CAUTION

• Do not try to touch the ventilation outlet on the left side (when seen from the front) as it can become heated

while the projector is turned on.

• Do no use the tilt-foot for purposes other than originally intended. Misuses such as gripping the tilt-foot or

hanging on the wall can cause damage to the projector.

• When carrying the projector by the carrying handle, make sure the two screws that attach the carrying handle

to the projector cabinet are tight.

Insufficient tightening of the two screws could result in the projector falling and causing injury.

• Do not send the projector in the soft carrying case by parcel delivery service or cargo shipment. The projector

inside the soft carrying case could be damaged.

• Select [High] in Fan mode if you continue to use the projector for consecutive days. (From the menu, select

[Advanced] → [Fan Mode] → [High].)

• Do not unplug the power cable from the wall outlet under any one of the following circumstances.

Doing so can cause damage to the projector:

While the Hour Glass icon appears.

While the cooling fans are running. (The cooling fans continue to work for 30 seconds after the projector is

turned off).

iii

Download from Www.Somanuals.com. All Manuals Search And Download.

Important Information

Lamp Replacement

•

To replace the lamp, follow all instructions provided on page 53.

Be sure to replace the lamp when the message “The lamp has reached the end of its usable life. Please

replace the lamp.” appears. If you continue to use the lamp after the lamp has reached the end of its usable

life, the lamp bulb may shatter, and pieces of glass may be scattered in the lamp case. Do not touch them as the

pieces of glass may cause injury.

If this happens, contact your Dukane dealer for lamp replacement.

•

Allow a minimum of 30 seconds to elapse after turning off the projector. Then turn off the main power switch,

disconnect the power cable and allow 60 minutes to cool the projector before replacing the lamp.

Download from Www.Somanuals.com. All Manuals Search And Download.

Table of Contents

Important Information.........................................................................i

1. Introduction ......................................................................................1

ᕡ What's in the Box? ........................................................................................................ 1

ᕢ Introduction to the Projector ......................................................................................... 2

ᕣ Part Names of the Projector ......................................................................................... 4

Attaching the Supplied Carrying Handle ................................................................ 5

Top Features ........................................................................................................... 6

Terminal Panel Features ......................................................................................... 7

ᕤ Part Names of the Remote Control .............................................................................. 8

8767A/8070 .......................................................................................................... 8

Battery Installation ........................................................................................... 10

Remote Control Precautions............................................................................ 10

Operating Range for Wireless Remote Control................................................ 10

8771 ...................................................................................................................... 11

Battery Installation ........................................................................................... 12

Remote Control Precautions............................................................................ 12

Operating Range for Wireless Remote Control................................................ 12

2. Installation and Connections.................................................... 13

ᕡ Setting Up the Screen and the Projector .................................................................... 13

Selecting a Location.............................................................................................. 13

Throw Distance and Screen Size.......................................................................... 15

ᕢ Making Connections ................................................................................................... 17

Enabling the computer’s external display.............................................................. 17

Connecting Your PC or Macintosh Computer........................................................ 17

To connect SCART output (RGB) ......................................................................... 18

Connecting an External Monitor ........................................................................... 19

Connecting Your DVD Player with Component Output .......................................... 20

Connecting Your VCR or Laser Disc Player .......................................................... 21

Connecting the Supplied Power Cable ................................................................. 22

3. Projecting an Image (Basic Operation) ................................. 23

ᕡ Turning on the Projector ............................................................................................. 23

Note on Startup Screen (Menu Language Select screen) .................................... 24

ᕢ Selecting a Source ..................................................................................................... 25

ᕣ Adjusting the Picture Size and Position ...................................................................... 27

ᕤ Correcting Keystone Distortion ................................................................................... 29

ᕥ Optimizing RGB Picture Automatically ....................................................................... 31

ᕦ Turning Up or Down Volume ....................................................................................... 31

ᕧ Turning off the Projector ............................................................................................. 32

ᕨ After Use..................................................................................................................... 32

Download from Www.Somanuals.com. All Manuals Search And Download.

Table of Contents

4. Convenient Features.................................................................... 33

ᕡ Turning Off the Image and Sound............................................................................... 33

ᕢ Freezing a Picture (8767A/8070 only) ........................................................................ 33

ᕣ Enlarging and Moving a Picture (8767A/8070 only) ................................................... 33

ᕤ Using the Remote Mouse Function (8767A/8070 only) .............................................. 34

5. Using On-Screen Menu................................................................ 35

ᕡ Using the Menus......................................................................................................... 35

ᕢ Menu Elements........................................................................................................... 37

ᕣ List of Menu Items ...................................................................................................... 38

ᕤ Menu Descriptions & Functions [Picture].................................................................... 40

ᕥ Menu Descriptions & Functions [Image] ..................................................................... 42

ᕦ Menu Descriptions & Functions [Setup] ..................................................................... 43

ᕧ Menu Descriptions & Functions [Advanced] ............................................................... 45

ᕨ Menu Descriptions & Functions [Information] ............................................................. 49

ᕩ Menu Descriptions & Functions [Default] ................................................................... 50

6. Maintenance ................................................................................... 51

ᕡ Cleaning or Replacing the Filter ................................................................................ 51

ᕢ Cleaning the Cabinet and the Lens ........................................................................... 52

ᕣ Replacing the Lamp................................................................................................... 53

7. Appendix .......................................................................................... 56

ᕡ Troubleshooting ......................................................................................................... 56

ᕢ Specifications ............................................................................................................ 59

ᕣ Cabinet Dimensions .................................................................................................. 61

ᕤ Pin Assignments of D-Sub COMPUTER Input Connector ........................................ 63

ᕥ Compatible Input Signal List ...................................................................................... 64

ᕦ PC Control Codes and Cable Connection ................................................................. 65

ᕧ Optional Presentation Remote Control Kit (PR52KIT)............................................... 67

ᕨ Troubleshooting Check List........................................................................................ 71

Download from Www.Somanuals.com. All Manuals Search And Download.

1. Introduction

ᕡ What's in the Box?

Make sure your box contains everything listed. If any pieces are missing, contact your dealer.

Please save the original box and packing materials if you ever need to ship your projector.

Projector

T O A D J .

A U

R - 2

P U T E

O M

T E R

M P U

C O

V -

T A N D

/ S

O N

V I D E

W E R

P O

A T U S

S T

L A M

S E L E C T

Power cable

C U

Soft carrying case

Lens cap

RGB signal cable

Important

Information

User's manual

Important Information

For 8767A and 8070 only

ENTER

-C

Remote control

(7N900521)

Carrying handle (24F39671)

Screw (M4

2: 24N07501)

Remote mouse receiver

(7N900561)

Batteries (AAA

Flathead screwdriver (24H51611)

For 8771 only

Remote control

(7N900551)

SELECT

SOURCE

ASPECT

PIC-M

UTE

Lithium battery (CR2032)

Download from Www.Somanuals.com. All Manuals Search And Download.

1. Introduction

ᕢ Introduction to the Projector

This section introduces you to your new Dukane Projector and describes the features and controls.

Congratulations on Your Purchase of The Dukane Projector

The 8767A/8070/8771 is one of the very best projectors available today. The this projector

enables you to project precise images up to 300 inches across (measured diagonally) from your PC or Macintosh

computer (desktop or notebook), VCR, DVD player, document camera, or a laser disc player.

You can use the projector on a tabletop or cart, you can use the projector to project images from behind the screen,

and the projector can be permanently mounted on a ceiling*¹. The remote control can be used wirelessly.

Do not attempt to mount the projector on a ceiling yourself.

The projector must be installed by qualified technicians in order to ensure proper operation and reduce the

risk of bodily injury.

In addition, the ceiling must be strong enough to support the projector and the installation must be in accor-

dance with any local building codes. Please consult your dealer for more information.

Features you'll enjoy:

•

Auto vertical keystone correction up to +/– 30 degrees

Built-in Wall Color Correction presets provide for adaptive color correction when projecting onto non-white

screen material.

•

Quick Start & Quick Shutoff

The quick start & quick shutoff function means you can set up or put away the projector without delay.

Nine seconds after turning on the power, the projector is ready to display PC or video images.

When you're finished, the fans stop in 30 seconds after turning off the power, so you can put away the projector

quickly after the conference or class.

•

Low level operation noise

Short focal length lens

130W lamp (110W Eco mode) : 8771

180W lamp (150W Eco mode) : 8767A/8070

•

Direct keys for source selection

New Color Management system

New menu design improves operation

Safety protect by Security function

Security feature prevents the projector from being used by unauthorized individuals.

Keyword prevents unauthorized individuals from changing projector settings or adjustments.

•

Exclusive Advanced intelligent pixel blending technology - an extremely accurate image

compression technology - offers a crisp image with UXGA (1600

1200) resolution*².

Supports most IBM VGA, SVGA, XGA , SXGA/UXGA, Macintosh, component signal

(YCbCr/ YPbPr) or any other RGB signals within a horizontal frequency range of 24 to 100 kHz and a

vertical frequency range of 50 to 120 Hz. This includes NTSC, PAL, PAL-N, PAL-M, PAL60, SECAM and

NTSC4.43 standard video signals.

A UXGA (1600

1200) and SXGA image (1280

1024) are on 8767A and 8771.

A UXGA (1600

1200), SXGA (1280

1024) and XGA (1024

768) image are displayed on 8070.

Download from Www.Somanuals.com. All Manuals Search And Download.

1. Introduction

NOTE: Composite video standards are as follows:

NTSC: U.S. TV standard for video in U.S. and Canada.

PAL: TV standard used in Western Europe.

PAL-N: TV standard used in Argentine, Paraguay and Uruguay.

PAL-M: TV standard used in Brazil.

PAL60: TV standard used for NTSC playback on PAL TVs.

SECAM: TV standard used in France and Eastern Europe.

NTSC4.43: TV standard used in Middle East countries.

•

You can use the supplied wireless remote control and remote mouse receiver to operate your PC mouse

wireless from across the room. The remote mouse receiver supports almost any PC using a USB connection

(8767A AND 8070).

•

You can control the projector with a PC or control system using the PC Control port.

The contemporary cabinet design is light, compact, easy to carry, and complements any office, boardroom or

auditorium.

About this user's manual

The fastest way to get started is to take your time and do everything right the first time. Take a few minutes now to

review the user's manual.This may save you time later on. At the beginning of each section of the manual you'll find an

overview. If the section doesn't apply, you can skip it.

•

IBM is a trademark or registered trademark of International Business Machines Corporation.

Mac and PowerBook are trademarks of Apple Computer, Inc., registered in the U.S. and other countries.

Windows, Windows 98, Windows Me, Windows XP or Windows 2000 are trademarks or registered trademarks

of Microsoft Corporation.

•

Other product and company names mentioned in this user’s manual may be the trademarks or registered

trademarks of their respective holders.

Download from Www.Somanuals.com. All Manuals Search And Download.

1. Introduction

ᕣ Part Names of the Projector

Front/Top

Zoom Lever

Controls

(See page 6)

(See page 28)

O M

Z O

J .

Ventilation (inlet) / Filter Cover

C U

I D

- V

(See page 51)

L E

S E

Focus Ring

(See page 28)

Z O O M

Remote sensor

(See page 10 for 8767A/8070)

(See page 12 for 8771)

C U

Built-in Security Slot ( )*

Ventilation (inlet)

Lens

Adjustable Tilt Foot Lever

(See page 27)

Lens Cap

Adjustable Tilt Foot

(See page 27)

This security slot supports the MicroSaver ® Security System. MicroSaver ® is a registered trademark of

Kensington Microware Inc. The logo is trademarked and owned by Kensington Microware Inc.

Rear

OCU

ZOOM

LECT

LAM

STATUS

WER

ON/STAND BY

IDEO

S-VIDEO

COMPUTER-1

COM

PUTER-2

AUTO

ADJ.

VIDEO IN

Monaural Speaker

L/MONO

AUDIO

S-VIDEO IN

Remote sensor

(See page 10 for 8767A/8070)

(See page 12 for 8771)

AUDIO

(1W)

COMPUTER

AUDIO OUT

AUDIO

COMPUTER OUT

COMPUTER

PC CONTROL

Ventilation (outlet)

AC IN

Heated air is exhausted from here.

AC Input

Connect the supplied power cable's two-pin plug here, and

plug the other end into an active wall outlet. (See page 22)

Terminal Panel

(See page 7)

Main Power Switch

When you plug the supplied power cable into an active wall outlet

and turn on the Main Power, the POWER indicator turns orange

and the projector is in standby mode.

(See page 23)

Download from Www.Somanuals.com. All Manuals Search And Download.

1. Introduction

Bottom

Lamp Cover

(See page 53)

Adjustable Tilt Foot

(See page 27)

Adjustable Tilt Foot Lever

(See page 27)

Adjustable Tilt Foot Lever

(See page 27)

For 8767A and 8070 only

Attaching the supplied carrying handle

You can carry the projector by attaching the supplied carrying handle securely to the projector.

To attach the supplied carrying handle, use the supplied flathead screwdriver and two screws.

Place a soft cloth on the working surface before turning the projector over to prevent scratching the top cover.

Make sure that the carrying handle is attached with correct orientation as shown below.

Flathead screwdriver

Screw

Carrying handle

CAUTION

When carrying the projector by the carrying handle, make sure the two screws that attach the carrying handle

to the projector cabinet are tight.

Download from Www.Somanuals.com. All Manuals Search And Download.

1. Introduction

Top Features

11 10 2 3 4

LAMP

STATUS

POWER

VIDEO

S-VIDEO

COMPUTER-1 COMPUTER-2

SELECT

ON/STAND BY

AUTO

ADJ.

7. COMPUTER1 and 2 Buttons

1. POWER Button (ON / STAND BY) (

)

Use this button to turn the power on and off when the

main power is supplied and the projector is in standby

mode.

To turn on the projector, press and hold this button for

a minimum of two seconds. To turn off the projector,

press this button twice.

Press this button to select an RGB source from com-

puter or component equipment connected to your

COMPUTER 1 or 2 port.

8. AUTO ADJ. Button

Use this button to adjust an RGB source for an opti-

mal picture (See page 31).

2. POWER Indicator

When this indicator is green, the projector is on;when

this indicator is orange, it is in standby mode. See the

Power Indicator section on page 56 for more details.

9. Source Indicators

When one of the COMPUTER, VIDEO or S-VIDEO

input is selected, the corresponding source indicator

lights.

3. STATUS Indicator

If this light blinks red rapidly, it indicates that an error

has occurred, the lamp cover is not attached properly

or the projector has overheated. If this light remains

orange, it indicates that you have pressed a cabinet

key while the Cabinet Button Lock is enabled. See the

Status Indicator section on page 56 for more details.

10. MENU Button

Displays the menu.

11. SELECT ̆̄̇̈ / Volume Buttons

̆̄ : Use these buttons to select the menu of the

item you wish to adjust.

̇̈ : Use these buttons to change the level of a se-

lected menu item. A press of the ̈ button ex-

ecutes the selection.When no menus appear,

these buttons work as a volume control.

When an image is magnified, the SELECT ̆̄̇̈

button moves the image.

4. LAMP Indicator

If this light blinks red rapidly, it's warning you that the

lamp has reached the end of its usable life. After this

light appears, replace the lamp as soon as possible

(See page 53). If this is lit green continually, it indi-

cates that the lamp mode is set to Eco. See the Lamp

Indicator section on page 56 for more details.

12. ENTER Button

Executes your menu selection and activates items

selected from the menu.

5. VIDEO Button

Press this button to select a video source from aVCR,

DVD player, laser disc player or document camera.

13. EXIT Button

Pressing this button will return to the previous menu.

While you are in the main menu, pressing this button

will close the menu.

6. S-VIDEO Button

Press this button to select an S-Video source from a

VCR, DVD player, laser disc player or document cam-

era.

Download from Www.Somanuals.com. All Manuals Search And Download.

1. Introduction

Terminal Panel Features

COMPUTER

AUDIO

COMPUTER

VIDEO IN

L/MONO AUDIO

S-VIDEO IN

AUDIO

AUDIO OUT

PC CONTROL

L/MONO

MONITOR OUT

1. COMPUTER 1 and 2 IN / Component Input Connector

For example, when a cable mini-plug is inserted into

the left AUDIO IN jack only, only left sound is output.

(Mini D-Sub 15 Pin)

Connect your computer or other analog RGB equip-

ment such as IBM compatible or Macintosh comput-

ers. Use the supplied RGB cable to connect to your

computer.This also serves as a component input con-

nector that allows you to connect a component video

output of component equipment such as a DVD player.

This connector also supports SCART output signal.

See page 18 for more details.

3. S-VIDEO IN Connector (Mini DIN 4 Pin)

Here is where you connect the S-Video input from an

external source like a VCR.

NOTE: S-Video provides more vivid color and higher

resolution than the traditional composite video format.

S-VIDEO AUDIO Input Jacks L/R (RCA)

COMPUTER AUDIO Input Mini Jack (Stereo Mini)

These are your left and right channel audio inputs for

stereo sound from an S-Video source.

This is where you connect the audio output from your

computer or DVD player when connected to the COM-

PUTER input.A commercially available audio cable is

required.

4. VIDEO IN Connector (RCA)

Connect aVCR, DVD player, laser disc player, or docu-

ment camera here to project video.

2. MONITOR OUT Connector (Mini D-Sub 15 Pin)

VIDEO AUDIO Input Jacks L/R (RCA)

You can use this connector to loop your computer

image to an external monitor from the RGB input

source.

These are your left and right channel audio inputs for

stereo sound from a Video source.

This connector outputs RGB signal in standby mode.

AUDIO OUT Mini Jack (Stereo Mini)

5. PC CONTROL Port (DIN 8 Pin)

You can use this jack to output sound from the cur-

rently selected source (COMPUTER, VIDEO or S-

VIDEO).Output sound level can be adjusted in accor-

dance with the sound level of the internal speaker.

Use this port to connect a PC or control system. This

enables you to control the projector using serial com-

munication protocol. If you are writing your own pro-

gram, typical PC control codes are on page 65.

Note that this cannot be used as a headphone jack.

(When audio equipment is connected, the projector

speaker is disabled.)

When a cable mini-plug is inserted into this jack, both

the right and left audio signals are not mixed, but sepa-

rate.

Download from Www.Somanuals.com. All Manuals Search And Download.

1. Introduction

ᕤ Part Names of the Remote Control

For 8767A/8070

5. PIC-MUTE Button

This button turns off the image and sound for a short

period of time. Press again to restore the image and

sound.

OFF

POWER

MAGNIFY PIC-MUTE

PAGE

6. PAGE UP/DOWN Button

Use these buttons to operate your computer with the

supplied remote mouse receiver. See page 34. You

can use these buttons to scroll the viewing area of the

window or to move to the previous or next slide in

PowerPoint on your computer.

DOWN

ENTER

7. MENU Button

Displays the menu for various settings and adjust-

ments.

EXIT

L-CLICK

MOUSE

R-CLICK

8. SELECT ̆̄̇̈ (Mouse) Button

̆̄ : Use these buttons to select the menu of the

item you wish to adjust.

VIDEO

COMPUTER AUTO ADJ.

̇̈ : Use these buttons to change the level of a se-

lected menu item. A press of the ̈ button ex-

ecutes the selection.

When an image is magnified, the SELECT ̆̄̇̈

button moves the image. See page 33.

S-VIDEO

VOLUME ASPECT

HELP

PICTURE FREEZE

9. ENTER Button

Use this button to enter your menu selection. It works

the same way as the ENTER button on the cabinet.

See page 6.

NOTE: If you are using a Macintosh computer, you can click

either the MOUSE R-CLICK or MOUSE L-CLICK button to

activate the mouse.

10. EXIT Button

It works the same way as the EXIT button on the cabi-

net. See page 6.

1. Infrared Transmitter

11. MOUSE L-CLICK Button

Direct the remote control toward the remote sensor

on the projector cabinet.

This button works as the mouse left button when the

supplied remote mouse receiver is connected with your

computer. See page 34.

2. POWER ON Button

When the main power is on, you can use this button

to turn your projector on.

12. MOUSE R-CLICK Button

This button works as the mouse right button when the

supplied remote mouse receiver is connected with your

computer. See page 34.

NOTE: To turn on the projector, press and hold the POWER

ON button for a minimum of two seconds.

13. VIDEO Button

3. POWER OFF Button

Press this button to select a video source from aVCR,

DVD player, laser disc player or document camera.

You can use this button to turn your projector off.

NOTE: To turn off the projector, press the POWER OFF

button twice.

14. S-VIDEO Button

Press this button to select an S-Video source from a

VCR.

4. MAGNIFY (+)(–) Button

Use this button to adjust the image size up to 400%.

The image is magnified about the center of the screen.

See page 33.

15. COMPUTER 1/2 Button

Press this button to select COMPUTER 1 or 2 (or Com-

ponent) input.

Download from Www.Somanuals.com. All Manuals Search And Download.

1. Introduction

OFF

POWER

MAGNIFY PIC-MUTE

PAGE

DOWN

ENTER

EXIT

L-CLICK

MOUSE

R-CLICK

VIDEO

COMPUTER AUTO ADJ.

S-VIDEO

VOLUME ASPECT

HELP

PICTURE FREEZE

16. AUTO ADJ. Button

Use this button to adjust an RGB source for an opti-

mal picture.

See page 31.

17. VOLUME (+)(–) Button

Press (+) to increase the volume and (–) to decrease

it.

18. ASPECT Button

Press this button once to display the Aspect Ratio

select menu.Keep pressing will change aspect ratios.

See page 42.

19. PICTURE Button

Press this button to display the Picture adjustement

menu to adjust Wall Color, Picture Management,

Brightness, Contrast, Sharpness, Color and Hue.See

pages 40 to 41.

20. HELP Button

Provides the information on the current signal and pro-

jector settings. See page 49.

21. FREEZE Button

This button will freeze a picture. Press again to re-

sume motion. See page 33.

Download from Www.Somanuals.com. All Manuals Search And Download.

1. Introduction

Battery Installation

1 _{Press firmly and slide the}

2 _{Remove both old batteries and}

3 _{Slip the cover back over the bat-}

teries until it snaps into place. Do

not mix different types of batter-

ies or new and old batteries.

battery cover off.

install new ones (AAA). Ensure

that you have the batteries' po-

larity (+/–) aligned correctly.

Remote Control Precautions

•

Handle the remote control carefully.

If the remote control gets wet, wipe it dry immediately.

Avoid excessive heat and humidity.

If you will not be using the remote control for a long time, remove the batteries.

Do not place the batteries upside down.

Do not use new and old batteries together, or use different types of batteries together.

Operating Range for Wireless Remote Control

Remote control

Remote sensor on projector cabinet

7m/22 feet

30°

7m/22 feet

•

The infrared signal operates by line-of-sight up to a distance of about 22 feet/7 m and within a 60-degree angle of

the remote sensor on the projector cabinet.

The projector will not respond if there are objects between the remote control and the sensor, or if strong light falls

on the sensor. Weak batteries will also prevent the remote control from properly operating the projector.

Download from Www.Somanuals.com. All Manuals Search And Download.

1. Introduction

For 8771

SELECT

SOURCE

ASPECT

PIC-MUTE

POWER

1. Infrared Transmitter

7. PIC-MUTE Button

Direct the remote control toward the remote sensor

on the projector cabinet.

This button turns off the image and sound for a short

period of time.

Press again to restore the image and sound.

2. MENU Button

Displays the menu for various settings and adjust-

ments.

8. ASPECT Button

Press this button once to display the Aspect Ratio

select menu. Keep pressing will change aspect ratios.

See page 42.

3. SELECT ̆̄̇̈ / Volume Buttons

̆̄ : Use these buttons to select the menu of the

item you wish to adjust.

9. POWER Button

̇̈ : Use these buttons to change the level of a se-

lected menu item. A press of the ̈ button ex-

ecutes the selection.When no menus appear,

these buttons work as a volume control.

Use this button to turn the power on and off when the

main power is supplied and the projector is in standby

mode.

To turn on the projector, press and hold this button for

a minimum of two seconds. To turn off the projector,

press this button once to display the confirmation

message and then press the POWER button or EN-

TER button.

4. ENTER Button

Executes your menu selection and activates items se-

lected from the menu.

5. EXIT Button

Pressing this button will return to the previous menu.

While you are in the main menu, pressing this button

will close the menu.

6. SOURCE Button

Press this button to select a video source such as a

PC, VCR or DVD player. Each time this button is

pressed, the input source will change as follows:

8771

Computer1 → Computer2 → Video → S-Video →

Computer1 → ...

Download from Www.Somanuals.com. All Manuals Search And Download.

1. Introduction

Battery Installation

1 _{Push the catch to the right}

and remove the battery

holder.

2 _{Remove the old Lithium coin cell}

3 _{Push the battery holder back into}

the remote control until you feel a

click.

and install new one (CR2032).

Ensure that the side with the

mark “+” is up.

CR2025

Remote Control Precautions

•

Handle the remote control carefully.

If the remote control gets wet, wipe it dry immediately.

Avoid excessive heat and humidity.

If you will not be using the remote control for a long time, remove the battery.

Do not place the battery upside down.

Keep the coin cell battery out of reach of children so as not to allow them to swallow the cell battery.

CAUTION

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type recommended by the manufacturer.

Dispose of used batteries according to your local regulations.

Operating Range for Wireless Remote Control

Remote control

Remote sensor on projector cabinet

7m/22 feet

30°

7m/22 feet

•

The infrared signal operates by line-of-sight up to a distance of about 22 feet/7 m and within a 60-degree angle of

the remote sensor on the projector cabinet.

The projector will not respond if there are objects between the remote control and the sensor, or if strong light falls

on the sensor.

Weak battery will also prevent the remote control from properly operating the projector.

Download from Www.Somanuals.com. All Manuals Search And Download.

2. Installation and Connections

This section describes how to set up your projector and how to connect video and audio sources.

Your projector is simple to set up and use.

But before you get started, you must first:

Set up a screen and the projector.

Connect your computer or video equip-

ment to the projector. See pages 17 to

21.

Connect the supplied power cable. See

page 22.

NOTE: Ensure that the power cable and any

other cables are disconnected before moving

the projector. When moving the projector or

when it is not in use, cover the lens with the

lens cap.

To the wall outlet.

ᕡ Setting Up the Screen and the Projector

Selecting a Location

The further your projector is from the screen or wall, the larger the image. The minimum size the image can be is

approximately 21" (0.53 m) measured diagonally when the projector is roughly 29 inches (0.73 m) from the wall or

screen. The largest the image can be is 300" (7.6 m) when the projector is about 393 inches (10 m) from the wall or

screen. Use the drawing below as a guide.

Screen Size (Unit: cm/inch

609.6(W)

457.2(H) / 240(W)

180(H)

Screen Size

300"

487.7(W)

365.8(H) / 192(W)

144(H)

240

406.4(W)

304.8(H) / 160(W)

120(H)

200

365.8(W)

274.3(H) / 144(W)

108(H)

180"

304.8(W)

228.6(H) / 120(W)

90(H)

150"

243.8(W)

182.9(H) / 96(W)

72(H)

120"

203.2(W)

152.4(H) / 80(W)

60(H)

100"

162.6(W)

121.9(H) / 64(W)

48(H)

80"

121.9(W)

91.4(H) / 48(W)

36(H)

60"

81.3(W)

61.0(H) / 32(W)

24(H)

10.0/393

61.0(W)

45.7(H) / 24(W)

18(H)

₃₀4_"0"

8.0/314

42.7(W)

32(H) / 17(W)

13(H)

21"

6.6/262

6.0/236

Lens center

5.0/196

0.7/

4.0/157

3.3/130

1.0/38

2.6/104

1.3/

2.0/78

Distance (Unit: m/inch)

Download from Www.Somanuals.com. All Manuals Search And Download.

2. Installation and Connections

Download from Www.Somanuals.com. All Manuals Search And Download.

2. Installation and Connections

Throw Distance and Screen Size

The following shows the proper relative positions of the projector and screen. Refer to the table to determine the

position of installation.

Distance Chart

Screen Width

Screen Diagonal

Screen center

Screen Height

(B)

Screen Bottom

(D)

Lens Center

B = Vertical distance between lens center and

screen center

C = Throw distance

Throw Angle (Ͱ)

D = Vertical distance between lens center and

bottom of screen (top of screen for ceiling

application)

Throw Distance (C)

α = Throw angle

NOTE: Distances may vary +/-5%.

Screen Size

Width

427

Diagonal

inch

Width

inch

120

144

160

168

192

216

240

Height

inch

Wide – Tele

inch

–– –

28 –

34 –

46 –

70 –

84 – 102

93 – 113

98 – 119

105 – 128

117 – 142

141 – 171

176 – 214

212 – 257

236 – 285

247 – 300

283 – 343

319 – 386

354 – 429

Wide – Tele

degree

–– – 9.9

Diagonal

533

635

762

Height

320

381

457

Wide – Tele

degree

–– – 9.9

inch

-30

-40

-50

-60

-90

-110

-120

-130

-140

-160

-190

-230

-280

-310

-330

-370

-420

-470

130

150

180

240

360

440

490

510

550

610

730

910

1090

1210

1270

1460

1640

1820

-1

-2

-4

-5

-6

-7

-9

––– – 730

720 – 870

870 – 1060

1170 – 1420

1770 – 2150

2130 – 2590

2370 – 2880

2490 – 3020

2670 – 3240

2970 – 3600

3580 – 4330

4480 – 5420

5380 – 6520

5980 – 7240

6280 – 7610

7190 – 8700

8090 – 9790

8990 – 10880

12.0 – 9.8

11.9 – 9.8

11.7 – 9.7

11.6 – 9.6

11.5 – 9.6

11.5 – 9.5

11.4 – 9.5

12.0 – 9.8

11.9 – 9.8

11.7 – 9.7

11.6 – 9.6

11.5 – 9.6

11.5 – 9.5

11.4 – 9.5

508

610

813

610

914

1016

1524

1829

2032

2134

2286

2540

3048

3810

4572

5080

5334

6096

6858

7620

1219

1463

1626

1707

1829

2032

2438

3048

3658

4064

4267

4877

5486

6096

1097

1219

1280

1372

1524

1829

2286

2743

3048

3200

3658

4115

4572

100

120

150

180

200

210

240

270

300

-11

-12

-13

-15

-17

-18

108

120

126

144

162

180

Download from Www.Somanuals.com. All Manuals Search And Download.

2. Installation and Connections

• Ensure that you have adequate ventilation around your

projector so heat can dissipate. Do not cover the vents

on the side or the front of the projector.

WARNING

* Installing your projector on the ceiling must be done

by a qualified technician.Contact your AV dealer for

more information.

* Do not attempt to install the projector yourself.

• Only use your projector on a solid, level surface. If the

projector falls to the ground, you can be injured and

the projector severely damaged.

• Do not use the projector where temperatures vary

greatly. The projector must be used at temperatures

between 41˚F (5˚C) and 95˚F (35˚C).

Reflecting the Image

Using a mirror to reflect your projector's image enables

you to enjoy a much larger image. Contact your

dealer if you need a mirror system. If you're using a mir-

ror system and your image is inverted, use the MENU

and SELECT buttons on your projector cabinet or your

remote control to correct the orientation. See page 44.

• Do not expose the projector to moisture, dust, or

smoke. This will harm the screen image.

Download from Www.Somanuals.com. All Manuals Search And Download.

2. Installation and Connections

ᕢ Making Connections

NOTE: When using with a notebook PC, be sure to connect between the projector and the notebook PC before turning on the

power to the notebook PC. In most cases signal cannot be output from RGB output unless the notebook PC is turned on after

connecting with the projector.

* If the screen goes blank while using your remote control, it may be the result of the computer's screen-saver or power

management software.

Enabling the computer’s external display

Displaying an image on the notebook PC’s screen does not necessarily mean it outputs a signal to the projector.

When using a PC compatible laptop, a combination of function keys will enable/disable the external display.

Usually, the combination of the ‘Fn” key along with one of the 12 function keys gets the external display to come on

or off. For example, NEC laptops use Fn + F3, while Dell laptops use Fn + F8 key combinations to toggle through

external display selections.

Connecting Your PC or Macintosh Computer

NOTE:

The COMPUTER 1 connector supports Plug & Play (DDC2).

COMPUTER 1 IN

COMPUTER 2 IN

VIDEO IN

COMPUTER

AUDIO

COMPUTER

L/MONO AUDIO

S-VIDEO IN

AUDIO

AUDIO OUT

PC CONTROL

L/MONO

MONITOR OUT

AUDIO

AC IN

RGB signal cable (supplied)

To mini D-Sub 15-pin connector on the projector. It

is recommended that you use a commercially

available distribution amplifier if connecting a

signal cable longer than the supplied one.

Audio cable

(not supplied)

PHONE

NOTE: For older Macintosh, use a

commercially available pin adapter

(not supplied) to connect to your

Mac's video port.

PHONE

IBM VGA or Compatibles (Notebook

type) or Macintosh (Notebook type)

IBM PC or Compatibles (Desktop type)

or Macintosh (Desktop type)

Connecting your PC or Macintosh computer to your projector will enable you to project your computer's screen image

for an impressive presentation.

To connect to a PC or Macintosh, simply:

1. Turn off the power to your projector and computer.

2. Use the supplied signal cable to connect your PC or Macintosh to the projector.

3. Connect the supplied power cable. See page 22.

4. Turn on the projector and the computer.

5. If the projector goes blank after a period of inactivity, it may be caused by a screen saver installed on the computer

you've connected to the projector.

Download from Www.Somanuals.com. All Manuals Search And Download.

2. Installation and Connections

NOTE: An image may not be displayed correctly when a Video or S-Video source is played back via a commercially available scan

converter.

This is because the projector will process a video signal as a computer signal at the default setting. In that case, do the following.

* When an image is displayed with the lower and upper black portion of the screen or a dark image is not displayed correctly:

Project an image to fill the screen and then press the AUTO ADJ button on the remote control or the AUTO ADJUST button on

the projector cabinet.

To connect SCART output (RGB) (Europe Operation)

Projector

COMPUTER 1 IN

VIDEO IN

COMPUTER

AUDIO

COMPUTER

L/MONO AUDIO

S-VIDEO IN

AUDIO

AUDIO OUT

PC CONTROL

L/MONO

MONITOR OUT

Video equipment such as DVD player

Female

AC IN

To COMPUTER 1 input

(COMPUTER input on VT47)

ADP-SC1

Commercially available SCART cable

Before connections: An exclusive SCART adapter (ADP-SC1) and a commercially available SCART cable are re-

quired for this connection.

NOTE: Audio signal is not available for this connection.

1. Turn off the power to the projector and your video equipment.

2. Use the ADP-SC1 SCART adapter and a commercially available SCART cable to connect the RGB input of

your projector and a SCART output (RGB) of your video equipment.

3. Connect the supplied power cable. See page 22.

4. Turn on the power to the projector and your video equipment.

5. Use the COMPUTER 1 button on the remote control to select the COMPUTER 1 input.

Use the COMPUTER button on the remote control to select the COMPUTER input on VT47.

6. Press the MENU button on the remote control to display the menu.

7. From the menu, select [Advanced] → [Signal Select] → [Computer 1 ([Computer] on VT47)] → [Scart].

SCART is a standard European audio-visual connector for TVs, VCRs and DVD players. It is also referred to as

Euro-connector.

NOTE: The ADP-SC1 SCART adapter is obtainable from your dealer in Europe. Contact your dealer in Europe for more

information.

Download from Www.Somanuals.com. All Manuals Search And Download.

2. Installation and Connections

Connecting an External Monitor

VIDEO IN

AUDIO

COMPUTER

AUDIO

COMPUTER

L/MONO

AUDIO

MONITOR OUT

S-VIDEO IN

AUDIO

AUDIO OUT

PC CONTROL

L/MONO

MONITOR OUT

AC IN

RGB signal cable (supplied)

RGB signal cable (not supplied)

You can connect a separate, external monitor to your projector to simultaneously view on a monitor the RGB analog

image you're projecting.

To do so:

1. Turn off the power to your projector, monitor and computer.

2. Use a 15-pin cable to connect your monitor to the MONITOR OUT (Mini D-Sub 15 pin) connector on your projector.

3. Connect the supplied power cable. See page 22.

4. Turn on the projector, monitor and the computer.

NOTE: Daisy chain connection is not possible.

Download from Www.Somanuals.com. All Manuals Search And Download.

2. Installation and Connections

Connecting Your DVD Player with Component Output

AUDIO

COMPUTER 1 IN

VIDEO IN

COMPUTER

AUDIO

COMPUTER

L/MONO AUDIO

S-VIDEO IN

AUDIO

AUDIO OUT

PC CONTROL

L/MONO

MONITOR OUT

AC IN

Optional 15p - to - RCA (female)

cable (ADP-CV1)

Component video RCA

cable (not supplied)

Audio Equipment

DVD player

bC Cr

AUDIO IN

Component

AUDIO OUT

Audio cable (not supplied)

You can connect your projector to a DVD player with component output or Video output. To do so, simply:

1. Turn off the power to your projector and DVD player.

2. If your DVD player has the component video (Y,Cb,Cr) output, use a commercially available component video cable

(RCA

3) and the optional 15-pin-to-RCA (female)

3 cable to connect your DVD player to the COMPUTER IN

connector on the projector.

For a DVD player without component video (Y,Cb,Cr) output, use common RCA cables (not provided) to connect a

composite VIDEO output of the DVD player to the Video Input of the projector.

3. Connect the supplied power cable. See page 22.

4. Turn on the projector and DVD player.

A component signal will be automatically displayed. If not, from the menu, select [Advanced] → [Signal Select] →

[Computer], and then place a check mark in the Component radio button.

NOTE: Refer to your DVD player's owner's manual for more information about your DVD player's video output requirements.

Download from Www.Somanuals.com. All Manuals Search And Download.

2. Installation and Connections

Connecting Your VCR or Laser Disc Player

VIDEO IN

AUDIO

VIDEO IN

L/MONO AUDIO

COMPUTER

AUDIO

COMPUTER

S-VIDEO IN

AUDIO

AUDIO OUT

PC CONTROL

L/MONO

MONITOR OUT

AUDIO

S-VIDEO IN

AC IN

S-Video cable (not supplied)

Video cable (not supplied)

Audio equipment

VCR/ Laser disc player

VIDEO S-VIDEO

VIDEO OUT

AUDIO IN

AUDIO OUT

Audio cable (not supplied)

Use an RCA or S-Video cable (not provided) to connect the video and use RCA cables (not provided) to connect

the audio from your VCR, laser disc player or document camera to your projector.

To make these connections, simply:

1. Turn off the power to the projector and VCR, laser disc player or document camera.

2. Connect one end of an RCA cable to the video output (or one end of an S-Video cable to the S-Video output

connector) on the back of your VCR or laser disc player, connect the other end to the appropriate video input

on your projector. Connect one end of a pair RCA cables (not supplied) to the audio output on the back of your

VCR or laser disc player, connect the other end to your audio equipment or to the appropriate audio input on

the projector.

Be careful to keep the right and left channel connections correct for stereo sound.

3. Connect the supplied power cable. See page 22.

4. Turn on the projector and the VCR or laser disc player.

NOTE: Refer to your VCR or laser disc player owner's manual for more information about your equipment's video output

requirements.

NOTE: An image may not be displayed correctly when a Video or S-Video source is played back in fast-forward or fast-rewind via

a scan converter.

Download from Www.Somanuals.com. All Manuals Search And Download.

2. Installation and Connections

Connecting the Supplied Power Cable

Connect the supplied power cable to the projector.

First connect the supplied power cable's two-pin plug to the AC IN of the projector, and then connect the other plug of

the supplied power cable in the wall outlet.

ZOOM

LECT

STA

-V

-1

-2

AUT

ADJ.

VIDEO IN

L/M

AUDIO

S-VIDEO IN

AUDIO

COMPUTER

AUDIO OUT

AUDIO

COMPUTER OUT

COMPUTER

PC CONTROL

To wall outlet ←

Make sure that the prongs are fully inserted into

both the AC IN and the wall outlet.

CAUTION:

Do not unplug the power cable from the wall outlet under any one of the following circumstances.

Doing so can cause damage to the projector:

•

While the Hour Glass icon appears.

•

While the cooling fans are running. The cooling fans continue to work for 30 seconds after the projector is

turned off.

Download from Www.Somanuals.com. All Manuals Search And Download.

3. Projecting an Image (Basic Operation)

This section describes how to turn on the projector and to project a picture onto the screen.

ᕡ Turning on the Projector

NOTE:

• The projector has two power switches: a main power switch and a POWER (ON/STAND BY) button.

• When plugging in or unplugging the supplied power cable, make sure that the main power switch is pushed to the off (⅜)

position. Failure to do so may cause damage to the projector.

LAMP

1. To turn on the main power to the projector, press the

STATUS

Main Power switch to the on position ( I ).

POWER

•

The POWER indicator will light orange.

See the Power Indicator section on page 56 for more

details.

LAMP

2. Press the POWER (ON/STAND BY) button on the

projector cabinet or the POWER button on the remote

control for a minimum of 2 seconds. The POWER

indicator will turn to green and the projector will

become ready to use.

STATUS

POWER

VIDEO

S-VIDEO

SELECT

ON/STAND BY

After you turn on your projector, ensure that the

computer or video source is turned on and that your

lens cap is removed.

8771

8767A8070

OFF

POWER

MAGNIFY PIC-MUTE

PAGE

SOURCE

PIC-MUTE

POWER

DOWN

NOTE: When no signal is available, a blue, black or logo screen is

displayed.

ASPECT

When the projector displays a blue or a black screen (not logo),

the Eco mode will be automatically selected in "Lamp Mode."

NOTE: If you turn on the projector immediately after the lamp is

turned off or when the temperature is high, the fans runs without

displaying an image for some time and then the projector will

display the image.

Standby

Blinking

Power On

LAMP

STATUS

POWER

STATUS

POWER

STATUS

POWER

Steady orange light

Blinking green Steady green

light light

See page 56 for more details.

Download from Www.Somanuals.com. All Manuals Search And Download.

3. Projecting an Image (Basic Operation)

Note on Startup screen (Menu Language Select screen)

When you first turn on the projector, you will get the Startup menu.This menu gives you the opportunity to select one

of the 8 menu languages.

To select a menu language, follow these steps:

1. Use the SELECT ̆ or ̄ button to select one of the 8

LAMP

languages for the menu.

STATUS

POWER

VIDEO

S-VIDEO

COMPUTER-1 COMPUTER-2

SELECT

ON/STAND BY

AUTO

ADJ.

8767A/8070

8771

OFF

POWER

MAGNIFY PIC-MUTE

PAGE

SELECT

DOWN

ENTER

EXIT

SOURCE

PIC-MUTE

LAMP

STATUS

POWER

2. Press the ENTER button to execute the selection.

VIDEO

S-VIDEO

COMPUTER-1 COMPUTER-2

SELECT

ON/STAND BY

After this has been done, you can proceed to the menu opera-

tion.

AUTO

ADJ.

If you want, you can select the menu language later. See "Lan-

guage" on pages 38 and 44.

8767A/8070

8771

OFF

POWER

MAGNIFY PIC-MUTE

PAGE

SELECT

DOWN

ENTER

EXIT

SOURCE

PIC-MUTE

NOTE: Immediately after turning on the projector, screen flicker may occur. This is not a fault. Wait 3 to 5 minutes until the lamp

lighting is stabilized.

When the Lamp mode is set to Eco, the LAMP indicator will light green.

If one of the following things happens, the projector will not turn on.

• If the internal temperature of the projector is too high, the projector detects abnormal high temperature. In this

condition the projector will not turn on to protect the internal system. If this happens, wait for the projector's internal

components to cool down.

• When the lamp reaches its end of usable life, the projector will not turn on. If this happens, replace the lamp.

• If the lamp fails to light, and if the STATUS indicator flashes on and off in a cycle of six times, wait a full minute and

then turn on the power.

Download from Www.Somanuals.com. All Manuals Search And Download.

3. Projecting an Image (Basic Operation)

ᕢ Selecting a Source

Selecting the computer or video source

LAMP

STATUS

NOTE: Turn on the computer or VCR connected to the projector.

POWER

VIDEO

S-VIDEO

COMPUTER-1 COMPUTER-2

SELECT

Using the cabinet buttons

Press any one of the COMPUTER 1/2

VIDEO and S-VIDEO buttons.

ON/STAND BY

AUTO

ADJ.

The corresponding indicator will light green.

8767A/8070

L-CLICK

R-CLICK

MOUSE

VIDEO

COMPUTER AUTO ADJ.

Using the Remote Control (8767A/8070)

Press any one of the COMPUTER 1/2, COMPONENT, VIDEO or S-

VIDEO buttons.

S-VIDEO

VOLUME ASPECT

HELP

PICTURE FREEZE

8771

Selecting from the Source List (8771)

1. Press and quickly release the SOURCE button on the remote

control.

SOURCE

ASPECT

PIC-MUTE

POWER

The Source list will be displayed.

8771

2. Press and quickly release the SOURCE button to select the

source in the Source list.

Each time the SOURCE button is pressed, the selection in the

Source list will change as follows:

8771

Computer 1 → Computer 2 → Video → S-Video → Computer 1 → ...

8771

3. Press the ENTER button to display the selected source.

NOTE: Highlighting the source for 2 seconds without pressing the ENTER

button will also display the selected source.

SOURCE

ASPECT

PIC-MUTE

POWER

Download from Www.Somanuals.com. All Manuals Search And Download.

3. Projecting an Image (Basic Operation)

Detecting the Signal Automatically

8771

Press and hold the SOURCE button for a minimum of 1 second, the

projector will search for the next available input source. Each time you

press and hold the SOURCE button for a minimum of 1 second, the

source will change as follows:

SOURCE

ASPECT

PIC-MUTE

POWER

8771

Computer 1 → Computer 2 → Video → S-Video → Computer 1 → ...

If no input signal is present, the input will be skipped.

Download from Www.Somanuals.com. All Manuals Search And Download.

3. Projecting an Image (Basic Operation)

ᕣ Adjusting the Picture Size and Position

Place your projector on a flat level surface and ensure that the projector is

square to the screen.

Lift the front edge of the projector to center the image vertically.

If the projected image does not appear square to the screen then use the

Keystone feature for proper adjustment. See page 29.

OCU

ZOO

Move the projector left to center the image horizontally on the screen.

Adjust the Tilt Foot

1. Lift the front edge of the projector.

A D J .

A U T O

2. Push up the Adjustable Tilt Foot Levers on the right and left sides

of the projector to extend the adjustable tilt feet (maximum height).

V -

I D

Adjustable Tilt

Foot Lever

Adjustable Tilt Foot

Adjustable Tilt

Foot Lever

3. Push down the Adjustable Tilt Foot Levers.

4. Lower the front of the projector to the desired height and release

the AdjustableTilt Foot Lever to lock the Adjustable tilt foot.There

is approximately 10 degrees of up and down adjustment for the

front of the projector.

C O M P U T E R - 2

C O M P U T E R - 1

S - V I D E O

V I D E O

O N / S T A N D B Y

W E R

P O

S T A T U S

L A M P

S E L E C T

Z O O M

C U

CAUTION

Do not use the tilt-foot for purposes other than originally intended. Misuses

such as gripping the tilt-foot or hanging on the wall can cause damage to the

projector.

Download from Www.Somanuals.com. All Manuals Search And Download.

3. Projecting an Image (Basic Operation)

Zoom

8767A/8070/8771

Use the ZOOM lever to finely adjust the image size on the

screen.

ZOO

NOTE: Digital Zoom can cause result in a blurry image because

zooming is made electronically.

Focus

Use the FOCUS ring to obtain the best focus.

Download from Www.Somanuals.com. All Manuals Search And Download.

3. Projecting an Image (Basic Operation)

ᕤ Correcting Keystone Distortion

Auto Keystone Correction

The Auto Keystone correction feature will correct the vertical distortion of a projected image on the screen. No special

operation required. Just put the projector on a flat surface.

Note that the vertical keystone angle can be corrected between 30 degrees upward and 30 degrees downward of

projector tilt from level.

NOTE: Auto and Manual Keystone correction angle could be less than 30 degrees depending on some kinds of signal and aspect

ratios.

NOTE: The Auto Keystone Correction feature can cause an image to be slightly blurred because the correction is made electroni-

cally.

Manual Keystone Correction

You can also correct the vertical keystone distor-

tion manually.

To do so:

1. Press the MENU button.

The menu will be displayed.

2. Turn off the Auto Keystone function.

Use the SELECT ̄ button to select

“Image” and then press the SELECT ̈

button.The “Auto Keystone” will be

displayed. Press the SELECT ̈ to select

“Off”.

3. Select the Keystone function.

Use the SELECT ̄ button to select

“Keystone”.

4. Correct the vertical distortion.

Use the SELECT ̇ or ̈ button to correct

the vertical keystone distortion.

NOTE: The Keystone Correction feature can cause

an image to be slightly blurred because the

correction is made electronically.

Download from Www.Somanuals.com. All Manuals Search And Download.

3. Projecting an Image (Basic Operation)

5. Press the MENU button to close the menu.

NOTE: You can save the changes using the Keystone Save

feature when you turn off the projector. See page 42.

Download from Www.Somanuals.com. All Manuals Search And Download.

3. Projecting an Image (Basic Operation)

ᕥ Optimizing RGB Picture Automatically

Adjusting the Image Using Auto Adjust

Optimizing an RGB image automatically.

Press the Auto Adjust button to optimize an RGB image automatically.

[Poor picture]

VIDEO

S-VIDEO

COMPUTER-1 COMPUTER-2

AUTO

ADJ.

8771

8767A/8070

[Normal picture]

L-CLICK

R-CLICK

MOUSE

VIDEO

COMPUTER AUTO ADJ.

S-VIDEO

SELECT

VOLUME ASPECT

HELP

PICTURE FREEZE

SOURCE

PIC-MUTE

Press the Auto Adjust button to fine-tune the computer image or to remove any vertical banding that might appear and

to reduce video noise, dot interference or cross talk (this is evident when part of your image appears to be shimmer-

ing). This function adjusts the clock frequencies that eliminate the horizontal banding in the image. This function also

adjusts the clock phase to reduce video noise, dot interference or cross talk. (This is evident when part of your image

appears to be shimmering.)

This adjustment may be necessary when you connect your computer for the first time.

NOTE:

Some signals may not be displayed correctly or take time.

• The Auto Adjust function does not work for component and video signal.

• If the Auto Adjust operation cannot optimize the RGB signal, try to adjust Horizontal/Vertical Position Clock and Phase

manually. See page 48.

ᕦ Turning Up or Down Volume

8767A/8070

L-CLICK

R-CLICK

Sound level from the speaker and the AU-

DIO OUT jack (Stereo mini) on the projec-

tor can be adjusted.

MOUSE

VIDEO

COMPUTER AUTO ADJ.

S-VIDEO

Increase volume

Decrease volume

VOLUME ASPECT

HELP

PICTURE FREEZE

8771

SELECT

Decrease volume

Increase volume

Download from Www.Somanuals.com. All Manuals Search And Download.

3. Projecting an Image (Basic Operation)

ᕧ Turning off the Projector

To turn off the projector:

LAMP

STATUS

First, press the POWER (ON/STAND BY) button on the

projector cabinet or the POWER OFF button on the re-

mote control. The “Power Off / Are you sure?” message

will appear.

POWER

VIDEO

S-VIDEO

COMPUTER-1 COMPUTER-2

SELECT

ON/STAND BY

AUTO

ADJ.

8767A/8070

8771

SELECT

OFF

POWER

MAGNIFY PIC-MUTE

PAGE

DOWN

SOURCE

ASPECT

PIC-MUTE

POWER

Secondly, press the ENTER button or press the POWER

(ON/STAND BY), the POWER OFF or the POWER button

again.

ENTER

EXIT

L-CLICK

R-CLICK

The power indicator will glow orange. After the projector

turns off, the cooling fans keep operating for 30 seconds

(Cooling-off time).

Power On

Fan running

Standby

Immediately after turning on the projector and displaying

an image, you cannot turn off the projector for 60 sec-

onds.

Finally, turn off the Main Power switch.The power indica-

tor will go out.

LAMP

STATUS

POWER

STATUS

POWER

STATUS

POWER

Steady green light

Blinking

orange light

Steady orange

light

CAUTION

Do not unplug the power cable from the wall outlet or do not turn off

the main power under any one of the following circumstances.Doing

so can cause damage to the projector:

• While the Hour Glass icon appears.

• While the cooling fans are running. (The cooling fans continue to

work for 30 seconds after the projector is turned off).

ᕨ After Use

Preparation: Make sure that the projector is turned off.

1. Unplug the power cable.

2. Disconnect any other cables.

3. Retract adjustable tilt feet if extended.

4. Cover the lens with the lens cap.

5. Put the projector and its accessories in the supplied soft carrying case.

Download from Www.Somanuals.com. All Manuals Search And Download.

4. Convenient Features

³ Turning off the Image and Sound

Press the PIC-MUTE button to turn off the image and sound for a short

period of time. Press again to restore the image and sound.

8767A/8070

8771

OFF

POWER

MAGNIFY PIC-MUTE

PAGE

SELECT

DOWN

ENTER

EXIT

SOURCE

PIC-MUTE

8767A/8070

· Freezing a Picture (8767A/8070 only)

S-VIDEO

VOLUME ASPECT

HELP

Press the FREEZE button to freeze a picture. Press again to resume

motion.

PICTURE FREEZE

NOTE: The optional remote control PR52 (RD-408E) allows you to use this

feature on 8771.

ᕣ Enlarging and Moving a Picture (8767A/8070 only)

You can enlarge the picture up to 400 percent.

To do so:

8767A/8070

1. Press the MAGNIFY (+) button to magnify the picture.

To move the magnified image, use the SELECT button.

OFF

POWER

MAGNIFY PIC-MUTE

PAGE

DOWN

ENTER

EXIT

LAMP

STATUS

POWER

VIDEO

S-VIDEO

COMPUTER-1 COMPUTER-2

SELECT

ON/STAND BY

AUTO

ADJ.

2. Return the image to the original size.

8767A/8070

OFF

POWER

MAGNIFY PIC-MUTE

PAGE

DOWN

ENTER

EXIT

NOTE: The optional remote control PR52 (RD-408E) allows you to use this

feature on 8771.

Download from Www.Somanuals.com. All Manuals Search And Download.

4. Convenient Features

ᕤ Using Remote Mouse Receiver (8767A/8070)

The remote mouse receiver enables you to operate your computer’s mouse functions from the remote control. It is a

great convenience for clicking through your computer-generated presentations.

Connecting the remote mouse receiver to your computer

If you wish to use the remote mouse function, connect the mouse receiver and computer.

The mouse receiver can be connected directly to the computer’s USB port (type A).

NOTE: Depending on the type of connection or OS installed on your computer, you may have to restart your computer or change

your computer settings.

Computer

Remote mouse receiver

To USB port of PC or Macintosh

When operating a computer via the remote mouse receiver

7m/22 feet

30˚

Remote sensor on the

remote mouse receiver

When connecting using the USB terminal

For PC, the mouse receiver can only be used with a Windows 98/Me/XP* or Windows 2000 operating system.

* NOTE: In Windows XP, if the mouse cursor will not move correctly, do the following:

Clear the Enhance pointer precision check box underneath the mouse speed slider in the Mouse Properties dialog box [Pointer

Options tab].

NOTE: Wait at least 5 seconds after disconnecting the mouse receiver before reconnecting it and vice versa. The computer may

not identify the mouse receiver if it is repeatedly connected and disconnected in rapid intervals.

Operating your computer’s mouse from the remote control

You can operate your computer's mouse from the remote control.

PAGE UP/DOWN Button: scrolls the viewing area of the window or to move to the previous or next slide in PowerPoint

on your computer.

̆̄̇̈ / Mouse Buttons: moves the mouse cursor on your computer.

MOUSE L-CLICK Button: works as the mouse left button.

MOUSE R-CLICK Button: works as the mouse right button.

Download from Www.Somanuals.com. All Manuals Search And Download.

5. Using On-Screen Menu

ᕡ Using the Menus

NOTE: The on-screen menu may not be displayed correctly while interlaced motion video image is projected.

1. Press the MENU button on the remote control or projector cabinet to display the Menu.

8767A/8070

8771

OFF

POWER

MAGNIFY PIC-MUTE

PAGE

SELECT

DOWN

ENTER

EXIT

SOURCE

PIC-MUTE

2. Press the SELECT ̆̄ buttons on the remote control or the projector cabinet to highlight the menu for

the item you want to adjust or set.

8767A/8070

8771

OFF

POWER

MAGNIFY PIC-MUTE

PAGE

SELECT

DOWN

ENTER

EXIT

SOURCE

PIC-MUTE

3. Press the SELECT ̈ button or the ENTER button on the remote control or the projector cabinet to select

a submenu or item.

8767A/8070

8771

OFF

POWER

MAGNIFY PIC-MUTE

PAGE

SELECT

DOWN

ENTER

EXIT

SOURCE

PIC-MUTE

Download from Www.Somanuals.com. All Manuals Search And Download.

5. Using On-Screen Menu

4. Use the SELECT ̆̄ buttons on the remote control or the projector cabinet to select the item you want

to adjust or set.

8767A/8070

8771

OFF

POWER

MAGNIFY PIC-MUTE

PAGE

SELECT

DOWN

ENTER

EXIT

SOURCE

PIC-MUTE

8767A/8070

8771

5. Adjust the level or turn the selected item on or off by using

SELECT ̇ or ̈ buttons on the remote control or the projector

cabinet.

OFF

POWER

MAGNIFY PIC-MUTE

PAGE

The on-screen slide bar will show you the amount of increase

or decrease.

SELECT

DOWN

ENTER

Changes are stored until you adjust it again.

EXIT

SOURCE

PIC-MUTE

EXIT ...................... Return to the previous menu.

6. Repeat steps 2-5 to adjust an additional item, or press the

MENU button to close the menu.

8767A/8070

8771

OFF

POWER

MAGNIFY PIC-MUTE

PAGE

SELECT

DOWN

ENTER

EXIT

SOURCE

PIC-MUTE

Download from Www.Somanuals.com. All Manuals Search And Download.

5. Using On-Screen Menu

· Menu Elements

Title

Slide bar

Highlight

Source

Off Timer remaining

time

Radio button

Solid triangle

Check mark

Tab

Thermometer symbol

Key symbol

Menu windows or dialog boxes typically have the following elements:

Title .......................................... Indicates the menu title.

Highlight................................... Indicates the selected menu or item.

Source ...................................... Indicates the currently selected source.

Remaining countdown time ..... Indicates the remaining countdown time when the Off Timer is preset.

Solid triangle ............................ Indicates further choices are available. A highlighted triangle indicates the item is active.

Tab ........................................... Indicates a group of features in a dialog box. Selecting on any tab brings its page to the front.

Radio button ............................ Use this round button to select an option in a dialog box.

Check mark .............................. Indicates the item is selected.

Slide bar ................................... Indicates settings or the direction of adjustment.

Key symbol .............................. Indicates the Cabinet Button Lock is enabled.

Thermometer symbol ............... Indicates the lamp mode is forcibly set to Eco mode because the internal temperature is too

high.

Download from Www.Somanuals.com. All Manuals Search And Download.

5. Using On-Screen Menu

» List of Menu Items

Picture

Wall Color

Off, Blackboard, Light yellow, Light green, Light blue, Sky blue, Light rose, Pink

Picture Management

Presentation, Video, Movie, Graphic, sRGB

User

Base Setting

Presentation, Video, Movie, Graphic, sRGB

Gamma Correction Dynamic, Black Detail, Natural

Brightness R,G,B

Contrast R,G,B

Brightness

Contrast

Sharpness

Color

Hue

Image

Auto Keystone

Keystone

On, Off

Keystone Save

Aspect Ratio

Cinema Position

On, Off

Normal, Wide Zoom, Cinema, Native

Setup

Off Timer

Off, 0:30, 1:00, 2:00, 3:00, 4:00, 6:00, 8:00

Normal, Eco

Lamp Mode

Language

Language-1 English, Deutsch, Français, Italiano, Español, Português, Nederlands

Language-2 Svenska, Norsk, Suomi, Cesky, Magyar, Polski, Türkçe

Language-3

, Dansk

Menu Color Select

Menu Display Time

Background

Color, Monochrome

Manual, Auto 5 sec, Auto 15sec, Auto 45 sec

Blue, Black, Logo

Orientation

Desktop Front, Ceiling Rear, Desktop Rear, Ceiling Front

On, Off

Beep

Advanced

Security

On, Off

Cabinet Button

Fan Mode

Lock, Unlock

High, Auto

Signal Select COMPUTER1* RGB/Component, RGB, Component, Scart

COMPUTER2 RGB/Component, RGB, Component

Video

Auto, NTSC3.58, NTSC4.43, PAL, PAL-M, PAL-N, PAL60, SECAM

S-Video

Page2

Power Management

Noise Reduction

Flicker Reduction

Auto Adjust

Horizontal

On, Off

Off, Normal, Fine

Vertical

Clock

Phase

Communication Speed 4800, 9600, 19200

Download from Www.Somanuals.com. All Manuals Search And Download.

5. Using On-Screen Menu

Information

Page1

Remaining Lamp Time, Lamp Hour Meter, Filter Usage, Projector Usage,

BIOS Version, Firmware Version, Data Version

Page2

Source Index, Horizontal Frequency, Vertical Frequency, Sync Polarity

Signal Type, Video Type, Sync Type, Interlace

Default

Factory Default

Current Signal

All Data

Clear Filter Usage

Clear Lamp Hour Meter

NOTE: Some menu items are not available depending on the input source.

Download from Www.Somanuals.com. All Manuals Search And Download.

5. Using On-Screen Menu

¿ Menu Descriptions & Functions [Picture]

Using the Wall Color Correction [Wall Color]

This function allows for quick adaptive color correction in applications where the screen material is not white.

The following eight options are available.

• OFF

• Blackboard

• Light green

• Sky blue

• Pink

• Light yellow

• Light blue

• Light rose

Using Picture Management [Picture Management]

This option allows you to adjust neutral tint for yellow, cyan or magenta.

There are 5 factory presets optimized for various types of images, or you can set user adjustable settings.

Presentation .......... Recommended for making a presentation using a PowerPoint file

Video ..................... Recommended for regular picture such as TV program

Movie .................... Recommended for movies

Graphic.................. Recommended for graphics

sRGB ..................... Standard color values

User ...................... User adjustable

Download from Www.Somanuals.com. All Manuals Search And Download.

5. Using On-Screen Menu

NOTE: When “sRGB”, “Graphic”, “Video” or “Movie” is selected, the brightness decreases slightly when compared to “Presenta-

tion”. This is not a malfunction.

User Adjust (when using User)

When selecting user adjustable presetting (User), the submenu will be displayed.

You can customize each gamma or color.To do so, first select “User” and press the ENTER button, and then proceed

the following steps.

Selecting Base Setting [Base Setting]

This feature allows you to use white balance or gamma values as reference data to optimize for various types of

images.You can select one of the following five settings.

• Presentation

• Movie

• Video

• Graphic

• sRGB

Selecting Gamma Correction Mode [Gamma Correction]

Each mode is recommended for :

Dynamic ................ Creates a high-contrast picture

Black Detail ........... Emphasizes detail in dark areas of the picture

Natural .................. Natural reproduction of the picture

Adjusting White Balance [Brightness RGB/Contrast RGB]

This allows you to adjust the white balance. Brightness for each color (RGB) is used to adjust the black level of the

screen; Contrast for each color (RGB) to adjust the white level of the screen.

Adjusting Brightness, Contrast, Sharpness, Color and Hue

Brightness ............. Adjusts the brightness level or the back raster intensity.

Contrast ................ Adjusts the intensity of the image according to the incoming signal.

Sharpness ............. Controls the detail of the image for Video.

Color ..................... Increases or decreases the color saturation level (not valid for RGB).

Hue........................ Varies the color level from +/– green to +/– blue. The red level is used as reference. This adjustment is only

valid for Video and Component inputs (not valid for RGB).

Download from Www.Somanuals.com. All Manuals Search And Download.

5. Using On-Screen Menu

´ Menu Descriptions & Functions [Image]

Enabling Auto Keystone [Auto Keystone]

This feature allows the projector to detect its tilt and correct vertical distortion automatically.

To turn on the Auto Keystone feature, select “On”.

Correcting Vertical Keystone Distortion Manually [Keystone]

You can correct vertical distortion manually from the menu when “Auto Keystone” is turned off.

You can save the changes using the Keystone Save feature when you turn off the projector.

Saving Vertical Keystone Correction [Keystone Save]

This option enables you to save your current keystone settings.

Saving your change once affects all sources. The changes are saved when the projector is off.

Selecting Aspect Ratio [ Aspect Ratio]

Aspect Ratio allows you to select the best Aspect mode to display your source image.You can also display the Aspect

Ratio menu by pressing the “ASPECT” button on the remote control.

Normal

Wide Zoom

Cinema

Native

When 4:3 is selected from

the source (i.e. DVD player),

the following selections will

display:

Standard

4:3 Aspect

Left and right

stretched

Left and right

stretched

Normal

Wide Zoom

Cinema

Native

When 16:9 is selected from

the source (i.e. DVD player),

the following selections will

display:

16:9 image displayed

in 4:3 mode

Left and right

stretched

Left and right stretched to

display the true aspect

Native (RGB only): Turns off the Advanced AccuBlend feature. The projector displays the current image in its true

resolution.

NOTE:

• While you are displaying an image at the projector’s native resolution or higher, “Native” is not available.

• You can adjust the image position for Cinema aspect. See “Cinema Position” for setting the image position.

Please note that using this projector for the purpose of commercial gain or the attraction of public attention in a venue such as a

coffee shop or hotel and employing compression or expansion of the screen image with a "Aspect Ratio" setting may raise

concern about the infringement of copyrights which are protected by copyright law.

Download from Www.Somanuals.com. All Manuals Search And Download.

5. Using On-Screen Menu

Adjusting the Vertical Position of Image [Cinema Position] (for Cinema only)

This feature adjusts the vertical position of the image when viewing video with Cinema aspect ratio selected.

When “Cinema” is selected in “Aspect Ratio”, the image is displayed with black borders on the top and bottom.

You can adjust the vertical position between top and bottom.

NOTE: This option is available only when “Cinema” is selected in Aspect Ratio.

² Menu Descriptions & Functions [Setup]

Using Off Timer [Off Timer]

You can set the timer so that the projector turns itself off at the preset time.

1. Use the SELECT ̆̄ to select your desired time between 30 minutes and 8 hours: Off, 0:30, 1:00, 2:00,

3:00, 4:00, 6:00 and 8:00.

2. Press the ENTER button.

3. The Off Timer starts counting down remaining time.

4. The projector turns off after the countdown is complete.

NOTE:

• To cancel the preset time, select “Off” for the preset time or turn off the power.

• When the remaining time reaches 3 minutes before the projector is turned off, the “Projector will turn off in 3 minutes”

message will be displayed on the bottom of the screen.

Selecting Lamp Mode [Lamp Mode]

This feature enables you to select two brightness modes of the lamp:

Normal and Eco modes. The lamp life can be extended by using the Eco mode.

Normal Mode ........ This is the default setting (100% Brightness).

Eco Mode .............. Select this mode to increase the lamp life (80% Brightness).

NOTE: If the projector is overheated in Normal mode, there may be a case where the Lamp mode automatically changes to Eco

mode to protect the projector. When the projector is in Eco mode, the picture brightness decreases. When the projector comes

back to normal temperature, the Lamp mode returns to Normal mode.

NOTE: Thermometer symbol indicates the lamp mode is automatically set to Eco mode because the internal temperature is too

high.

Download from Www.Somanuals.com. All Manuals Search And Download.

5. Using On-Screen Menu

Selecting Menu Language [Language]

You can choose one of 21 languages for on-screen instructions.

Selecting Menu Color [Menu Color Select]

You can choose between two color modes for menu color: color and monochrome.

Selecting Menu Display Time [Menu Display Time]

This option allows you to select how long the projector waits after the last touch of a button to turn off the menu.

The preset choices are “Manual”, “Auto 5 sec”, “Auto 15 sec”, and “Auto 45 sec”. The “Auto 45 sec” is the factory

preset.

Selecting a Color or Logo for Background [Background]

Use this feature to display a black/ blue screen or logo when no signal is available.

Selecting Projector Orientation [Orientation]

This sets your image for your type of projection. The options are:

desktop front projection, ceiling rear projection, desktop rear projection, and ceiling front projection.

Enabling Key Sound and Error Sound [Beep]

This feature turns on or off the keypad sound or alarm when a button on the cabinet and the remote control is pressed

or an error occurs.

Download from Www.Somanuals.com. All Manuals Search And Download.

5. Using On-Screen Menu

¶ Menu Descriptions & Functions [Advanced]

Security

A keyword can be set for your projector to avoid operation by an unauthorized user using the Menu. When a keyword

is set, turning on the projector will display the Keyword input screen. Unless the correct keyword is entered, the

projector cannot project an image.

To enable the Security function:

1. Select [Advanced] → [Security] and press the ̇ button to select “On”.

The [Keyword] screen will be displayed.

2. Type in a combination of the four SELECT buttons ̆̄̇̈ and press the ENTER button.

NOTE: A keyword must be four to 10 digits in length.

The [Confirm Keyword] screen will be displayed.

Download from Www.Somanuals.com. All Manuals Search And Download.

5. Using On-Screen Menu

3. Type in the same combination of SELECT buttons ̆̄̇̈ and press the ENTER button.

The confirmation screen will be displayed.

4. Select “Yes” and press the ENTER button.

The Security function has been enabled.

To disable the Security function:

1. Select [Advanced] → [Security] and press the ̈ button to select “Off”.

The Keyword confirmation screen will be displayed.

2. Type in your keyword and press the ENTER button.

When the correct keyword is entered, the Security function will be disabled.

When the Security function is enabled and the projector is turned on, the projector will display a blue

background.

To display an image at this time, press the MENU button to display the Keyword input screen.

Type in the correct keyword and press the ENTER button.The projector will display an image.

NOTE:

• The security disable mode is maintained until the main power is turned off (by setting the main power switch to “O” or

unplugging the power cable).

• If you forget your keyword, contact your dealer. Your dealer will provide you with your keyword in exchange for your request

code. Your request code is displayed in the Keyword Confirmation screen. In this example “K992-45L8-JNGJ-4XU9-1YAT-

EEA2” is a request code.

Download from Www.Somanuals.com. All Manuals Search And Download.

5. Using On-Screen Menu

Disabling the Cabinet Buttons [Cabinet Button Lock]

This option turns on or off the Cabinet Button Lock function.

NOTE:

• This Cabinet Button Lock does not affect the remote control and the PC Control functions.

• When the cabinet buttons are unlocked, pressing and holding the EXIT button for about 10 seconds will change the setting to

enable.

• Key symbol indicates the Cabinet Button Lock is enabled.

Enabling High Speed Fan Mode [Fan Mode]

This option allows you to select two modes for fan speed: High speed mode and Auto mode.

High ...................... The built-in fans run at a fixed high speed.

Auto ...................... The built-in fans automatically run at a variable speed according to the internal temperature.

When you wish to cool down the temperature inside the projector quickly, select “High”.

NOTE: Select “High” if you continue to use the projector for consecutive days.

Selecting Signal Format [Signal Select]

[Computer]

Allows you to choose “Computer” for an RGB source such as a computer, or “Component” for a component video

source such as a DVD player.Normally select “RGB/Component” and the projector automatically detects a compo-

nent signal. However there may be some component signals that the projector is unable to detect. If this is the

case, select “Component”. Select “Scart” in Computer 1 for the European Scart signal.

[Video & S-Video System Select]

This feature enables you to select composite video standards manually. Normally select “Auto”.

When you select the video standard for Video and S-Video, select the video standard from the pull-down menu.

This must be done for Video and S-Video respectively.

Download from Www.Somanuals.com. All Manuals Search And Download.

5. Using On-Screen Menu

(Advanced Page 2)

Enabling Power Management [Power Management]

When this option is on and there is no input for five minutes or more, the projector will automatically turn itself off.

Turning On Noise Reduction [Noise Reduction] (not available for Video and S-Video signals)

Reduces video noise. Select “On” to enable the Noise Reduction feature.

Turning On Flicker Reduction [Flicker Reduction]

Reduces flicker which can occur in an interlaced signal. This feature is not available for RGB and HDTV signals.

NOTE: When the Flicker Reduction is ON, jagged lines can be visible depending on the signal. In that case, select OFF.

NOTE: This feature may not be available depending on your video equipment connected to the projector.

Setting Auto Adjust [Auto Adjust]

This feature sets the Auto Adjust mode so that the RGB image can be automatically or manually adjusted for noise

and stability.You can automatically make adjustment in two ways: Normal and Fine

Off ......................... The RGB image will not be automatically adjusted.

You can manually optimize the RGB image.

Normal .................. Default setting. The RGB image will be automatically adjusted. Normally select this option.

Fine ....................... Select this option if fine adjustment is needed. It takes more time to switch to the source than when “Nor-

mal” is selected.

Adjusting Position/Clock (when Auto Adjust is off)

This allows you to manually adjust the image horizontally and vertically, and adjust Clock and Phase.

[Horizontal/Vertical]

Adjusts the image location horizontally and vertically.

This adjustment is made automatically when the Auto Adjust is turned on.

[Clock] (available for RGB and HDTV signals only)

Use this item with the “Auto Adjust off” to fine tune the computer image or to remove any vertical banding that

might appear. This function adjusts the clock frequencies that eliminate the horizontal banding in the image. This

adjustment may be necessary when you connect your computer for the first time. This adjustment is made auto-

matically when the Auto Adjust is turned on.

Download from Www.Somanuals.com. All Manuals Search And Download.

5. Using On-Screen Menu

[Phase] (available for RGB and HDTV signals only)

Use this item to adjust the clock phase or to reduce video noise, dot interference or cross talk. (This is evident

when part of your image appears to be shimmering.)

Use “Phase” only after the “Clock” is complete.

This adjustment is made automatically when the Auto Adjust is turned on.

Selecting Communication Speed [Communication Speed]

This feature sets the baud rate of the PC Control port (DIN 8 Pin). It supports data rates from 4800 to 19200 bps.

The default is 19200 bps.

Select the appropriate baud rate for your equipment to be connected (depending on the equipment, a lower baud rate

may be recommended for long cable runs).

º Menu Descriptions & Functions [Information]

Displays the status of the current signal, remaining lamp (%), lamp/filter/projector usage time (hours) and version

information. The Information has two pages. The Information included is as follows:

[Page 1]

Remaining Lamp Time (%)*

Lamp Hour Meter (H)

Filter Usage

Projector Usage

The progress indicator shows the percentage of remaining bulb life. The value informs you of the amount of

lamp usage. When the remaining lamp time reaches 0, the Remaining Lamp Time bar indicator changes

from 0% to 100 Hours and starts counting down.

If the remaining lamp time reaches 0 hours, the projector will not turn on regardless of whether the lamp

mode is set to Normal or Eco.

BIOS Version

Firmware Version

Data Version

[Page 2]

Source Index

Horizontal Frequency

Vertical Frequency

Sync Polarity

Signal Type

Video Type

Sync Type

Interlace

Download from Www.Somanuals.com. All Manuals Search And Download.

5. Using On-Screen Menu

¾ Menu Descriptions & Functions [Default]

Returning to Factory Default [Factory Default]

The Factory Default feature allows you to change adjustments and setting to the factory preset.

[Current Signal]

Resets the adjustments for the current signal to the factory preset levels.

The items that can be reset are: Brightness, Contrast, Color, Hue, Sharpness, Noise Reduction, Aspect Ratio,

Horizontal Position, Vertical Position, Clock, Phase and Picture Management.

[All Data]

Reset all the adjustments and settings for all the signals to the factory preset for source except the following:

Language, Security, Communication Speed, Remaining LampTime, Lamp Hour Meter, Filter Usage and Projector

Usage. To reset the lamp usage time, see “Clear Lamp Hour Meter” and “Clear Filter Usage”.

Resetting the Filter Usage Hours [Clear Filter Usage]

Resets the filter usage back to zero. Selecting this option displays submenu for a confirmation. Select “Yes” and press

the ENTER button.

Clearing Lamp Hour Meter [Clear Lamp Hour Meter]

Resets the lamp clock back to zero. Selecting this option displays submenu for a confirmation. Select “Yes” and press

the ENTER button.

NOTE: The projector will turn off and go into standby mode after 2100 hours (up to 3100 hours in Eco mode) of service. If this

happens, do the following while in standby condition to clear values for the Lamp Hour Meter:

For 8767A/8070 press the HELP button on the remote control for a minimum of 10 seconds.

For 8771 press and hold the POWER and the EXIT buttons on the remote control simultaneously for a minimum of 10

seconds.

When the lamp time clock is reset to zero, the LAMP indicator goes out.

Do this only after replacing the lamp.

Download from Www.Somanuals.com. All Manuals Search And Download.

6. Maintenance

This section describes the simple maintenance procedures you should follow to clean the filter and replace the lamp.

ᕡ Cleaning or Replacing the Filter

The air-filter sponge keeps dust and dirt from getting inside the projector and should be cleaned after every 100 hours

of operation (more often in dusty conditions). If the filter is dirty or clogged, your projector may overheat.

CAUTION

•

Turn off the projector, turn off the main power switch and unplug the projector before replacing the filter.

Only clean the outside of the filter cover with a vacuum cleaner.

Do not attempt to operate the projector without the filter cover.

To clean the air-filter:

Vacuum the filter-through the filter cover.

V -

O O

C U

To reset the filter usage time, from the menu, select [Default] → [Clear Filter Usage].

See also page 50 for resetting the filter usage time.

To replace the filter (sponge):

1. Remove the filter cover by pushing down on the catch of the cover until you feel it detach.

Catch

2. Gently peel off the filter (sponge) and replace it with the new one.

Download from Www.Somanuals.com. All Manuals Search And Download.

6. Maintenance

3. Reinstall the new filter cover.

NOTE: Do not wash the filter with soap and water. Soap and water will damage the filter membrane. Before replacing the filter,

remove dust and dirt from the projector cabinet. Keep out dust and dirt during filter replacement.

NOTE: When you replace the lamp, it is also wise to replace the filter. The filter comes in the same package with your replacement

lamp.

· Cleaning the Cabinet and the Lens

1. Turn off the projector before cleaning.

2. Clean the cabinet periodically with a damp cloth. If heavily soiled, use a mild detergent. Never use strong

detergents or solvents such as alcohol or thinner.

3. Use a blower or lens paper to clean the lens, and be careful not to scratch or mar the lens.

C O M P U T E R - 2

C O M P U T E R - 1

S - V I D E O

V I D E O

O N / S T A N D B Y

W E R

P O

S T A T U S

L A M P

S E L E C T

-V

-1

-2

VID

EO IN

UDIO

S-VID

EO IN

AUDIO

C U

DIO

MPUTER

DIO

COM

TER

PUTER

NTR

Download from Www.Somanuals.com. All Manuals Search And Download.

6. Maintenance

» Replacing the Lamp

After your lamp has been operating for 2000 hours (up to 3000 hours in Eco mode) or longer, the LAMP indicator in the

cabinet will blink red and the message will appear. Even though the lamp may still be working, replace it at 2000 (up to

3000 hours in Eco mode) hours to maintain optimal projector performance. After replacing the lamp, be sure to clear

the lamp hour meter. See page 50.

CAUTION

•

DO NOT TOUCH THE LAMP immediately after it has been used. It will be extremely hot. Turn the projector off,

wait 30 seconds, turn off the main power switch and then disconnect the power cable. Allow at least one hour

for the lamp to cool before handling.

•

DO NOT REMOVE ANY SCREWS except two lamp case screws.You could receive an electric shock.

Do not break the glass on the lamp housing.

Keep finger prints off the glass surface on the lamp housing. Leaving finger prints in the glass surface might

cause an unwanted shadow and poor picture quality.

•

The projector will turn off and go into stand by mode after 2100 (up to 3100 hours in Eco mode) hours of

service. If this happens, be sure to replace the lamp. If you continue to use the lamp after 2000 hours (up to

3000 hours in Eco mode) of use, the lamp bulb may shatter, and pieces of glass may be scattered in the lamp

case. Do not touch them as the pieces of glass may cause injury. If this happens, contact your NEC dealer for

lamp replacement.

To replace the lamp:

Optional lamp and tools needed for replacement:

•

Replacement lamp. 465-8767A (8767A/8070) or 465-8771 (8771).

Phillips screwdriver or equivalent

NOTE: The two lamp houses are slightly different in appearance.

The following explanation uses drawings for the lamp 465-8767A.

1. Place the projector on a soft cloth and turn it over to access the lamp cover on the bottom.

2. Use a Philips screwdriver to push and release the tab.

Push up and remove the lamp cover.

Philips

screwdriver

Catch

Download from Www.Somanuals.com. All Manuals Search And Download.

6. Maintenance

3. Loosen the two screws securing the lamp housing until the phillips screwdriver goes into a freewheeling

condition.The two screws are not removable.

Remove the lamp housing by holding it.

Interlock

NOTE: There is an interlock on this case to prevent the risk of electrical shock. Do not attempt to circumvent this interlock.

4. Insert a new lamp housing until the lamp housing is plugged into the socket.

CAUTION

Do not use a lamp other than the Dukane replacement lamp 465-8767A (8767A/8070) or 465-8771 (8771).

Order this from your Dukane dealer.

Secure it in place with the two screws.

Be sure to tighten the screws.

5. Reattach the lamp cover.

Slip the lamp cover back until it snaps into place.

Download from Www.Somanuals.com. All Manuals Search And Download.

6. Maintenance

6. Finally, select the menu → [Default] → [Clear Lamp Hour Meter] to reset the lamp usage hours.

NOTE: When the lamp exceeds 2100 hours (up to 3100 hours in Eco mode) of service, the projector cannot turn on and the menu

is not displayed. If this happens, do the following while in standby condition to clear values for the Remaining Lamp Time and the

Lamp Hour Meter:

For 8767A/8070 press the HELP button on the remote control for a minimum of 10 seconds.

For 8771 press and hold the POWER and the EXIT buttons on the remote control simultaneously for a minimum of 10

seconds.

When the lamp time clock is reset to zero, the LAMP indicator goes out.

Download from Www.Somanuals.com. All Manuals Search And Download.

7. Appendix

ᕡ Troubleshooting

This section helps you resolve problems you may encounter while setting up or using the projector.

Indicator Messages

Power Indicator

Indicator Condition

Projector Condition

The main power is off

The projector is getting ready to turn on. Wait for a moment.

Note

Off

–

Blinking light

Green

0.5 sec On,

0.5 sec Off

2.5 sec On,

0.5 sec Off

0.5 sec On,

0.5 sec Off

Off Timer is enabled.

–

Orange

The projector is cooling down.

Wait for a moment.

Steady light

Green

The projector is turned on.

The projector is in Standby.

–

Orange

Status Indicator

Indicator Condition

Off

Projector Condition

Note

Normal

–

Blinking light

Red

1 cycle (0.5 sec On, Lamp cover error or lamp housing error Replace the lamp cover or lamp

2.5 sec Off)

housing correctly.

2 cycle (0.5 sec On, Temperature error

0.5 sec Of)

The projector is overheated. Move

the projector to a cooler location.

Fans will not work correctly.

4 cycle (0.5 sec On, Fan error

0.5 sec Off)

6 cycle (0.5 sec On, Lamp error

0.5 sec Off)

Lamp fails to light. Wait a full

minute and then turn on again.

Green

Re-firing the lamp (The projector is cool- The projector is re-firing.

ing down.)

Wait for a moment.

Steady light

Orange

Cabinet button is locked

You have pressed cabinet button

when Cabinet Button is locked.

Lamp Indicator

Indicator Condition

Projector Condition

Note

Off

Normal

–

Red

Blinking light

Steady light

Lamp has reached its end of life. Lamp Replace the lamp.

replacement message will be displayed.

Lamp has been used beyond its limit. The Replace the lamp.

projector will not turn on until the lamp is

replaced.

Red

Green

Lamp mode is set to Eco mode

–

Download from Www.Somanuals.com. All Manuals Search And Download.

7. Appendix

Common Problems & Solutions (See also "Power/Status/Lamp Indicator" on page 56.)

Problem

CheckThese Items

Does not turn on

•

Check that the power cable is plugged in and that the power button on the projector cabinet or the remote

control is on. See pages 22 and 23.

•

Ensure that the lamp cover is installed correctly. See page 54.

Check to see if the projector has overheated or the lamp usage exceeds 2100 hours (up to 3100 hours : Eco

mode). If there is insufficient ventilation around the projector or if the room where you’re presenting is par-

ticularly warm, move the projector to a cooler location.

The lamp may fail to light. Wait a full minute and then turn on the power again.

The lamp has reached the end of its usable life. Replace the lamp.

•

Will turn off

No picture

•

Ensure that the Power Management is off. See page 48.

Use the VIDEO, the S-VIDEO or the COMPUTER button (the SOURCE button on 8771) on the remote

control to select your source (Computer, Video or S-Video). See page 25. If there is still no picture, press the

button again.

Ensure your cables are connected properly.

Use menus to adjust the brightness and contrast. See page 41.

Remove the lens cap.

Reset the settings or adjustments to factory preset levels using the “Default” in the Menu. See page 50.

Enter your registered keyword if the Security function is enabled. See page 45.

When using with a notebook PC, be sure to connect between the projector and the notebook PC before turning

on the power to the notebook PC. In most cases signal cannot be output from RGB output unless the notebook

PC is turned on after connecting with the projector.

* If the screen goes blank while using your remote control, it may be the result of the computer's screen-

saver or power management software.

See also the next page.

•

Picture suddenly

becomes dark

When one of the following happens, the Lamp mode automatically changes from Normal to Eco.

* When there are no signals (blue or black screen) → To return to the Normal mode, select another available

source.

* When the image is muted using the PIC-MUTE button on the remote control → Press the PIC-MUTE button

again to return to the Normal mode.

* When the room where you' re presenting is particularly warm → Move the projector to a cooler location.

Color tone or hue is

unusual

•

Check if an appropriate color is selected in "Wall Color". If so, select an appropriate option. See page 40.

Adjust "Hue" in "Picture". See page 41.

Image isn’t square to

the screen

•

Reposition the projector to improve its angle to the screen. See page 27.

Use the Keystone correction function to correct the trapezoid distortion. See page 29.

Picture is blurred

•

Adjust the focus. See page 28.

Reposition the projector to improve its angle to the screen. See page 27.

Ensure that the distance between the projector and screen is within the adjustment range of the lens. See

pages 13.

•

Condensation may form on the lens if the projector is cold, brought into a warm place and is then turned on.

Should this happen, let the projector stand until there is no condensation on the lens.

Image is scrolling

vertically, horizontally

or both

•

Use the SOURCE button on the projector cabinet or the VIDEO, the S-VIDEO or the COMPUTER button (the

SOURCE button on 8771) on the remote control to select your source (Video, S-Video or Computer).

See page 25.

•

Adjust the computer image manually with the Horizontal/Vertical in the “Advanced → Page 2”. See page 48.

Remote control does

not work

Install new batteries.

8767A/8070: AAA

2. See page 10.

8771:

Lithium coin cell (CR2032). See page 12.

•

Make sure there are no obstacles between you and the projector.

Stand within 22 feet (7 m) of the projector. pages 10 for 8767A/8070 and 12 for 8771.

Indicator is lit or

blinking

•

See the POWER/STATUS/LAMP Indicator on page 56.

Cross color in RGB

mode

•

Press the AUTO ADJUST button on the projector cabinet or the AUTO ADJ. button on the remote control. See

page 31.

When “Off” is selected in Auto Adjust, adjust the computer image manually with Clock/Phase in “Advanced →

Page 2” in the menu. See page 48.

For more information contact your dealer.

Download from Www.Somanuals.com. All Manuals Search And Download.

7. Appendix

If there is no picture, or the picture is not displayed correctly.

•

Power on process for the projector and the PC.

Be sure to connect the RGB cable between the projector and the computer before turning on the computer.

There are some notebook PCs, which do not output signal unless there is a projector or monitor connected first.

NOTE: You can check the horizontal frequency of the current signal in the projector’s menu under Information. If it reads

“0kHz”, this means there is no signal being output from the computer. See page 49 or go to next step.

•

Enabling the computer’s external display.

Displaying an image on the notebook PC’s screen does not necessarily mean it outputs a signal to the projec-

tor. When using a PC compatible laptop, a combination of function keys will enable/disable the external display.

Usually, the combination of the ‘Fn” key along with one of the 12 function keys gets the external display to come

on or off. For example, NEC laptops use Fn + F3, while Dell laptops use Fn + F8 key combinations to toggle

through external display selections.

•

Non-standard signal output from the computer

If the output signal from a notebook PC is not an industry standard, the projected image may not be displayed

correctly. Should this happen, deactivate the notebook PC’s LCD screen when the projector display is in use.

Each notebook PC has a different way of deactivate/reactivate the local LCD screens as described in the

previous step. Refer to your computer’s documentation for detailed information.

Image displayed is incorrect when using a Macintosh

When using a Macintosh with the projector, set the DIPswitch of the Mac adapter (not supplied with the projec-

tor) according to your resolution. After setting, restart your Macintosh for the changes to take affect.

For setting display modes other than those supported by your Macintosh and the projector, changing the DIP

switch on a Mac adapter may bounce an image slightly or may display nothing. Should this happen, set the DIP

switch to the 13” fixed mode and then restart your Macintosh. After that, restore the DIP switches to a

displayable mode and then restart the Macintosh again.

NOTE: A Video Adapter cable manufactured by Apple Computer is needed for a PowerBook which does not have a mini D-Sub

15-pin connector.

•

Mirroring on a PowerBook

When using the projector with a Macintosh PowerBook, output may not be set to 1024 x 768 unless “mirror-

ing” is off on your PowerBook. Refer to owner’s manual supplied with your Macintosh computer for mirroring.

Folders or icons are hidden on the Macintosh screen

Folders or icons may not be seen on the screen. Should this happen, select [View] → [Arrange] from the Apple

menu and arrange icons.

Download from Www.Somanuals.com. All Manuals Search And Download.

7. Appendix

ᕢ Specifications

This section provides technical information about the 8767A/8070/8771 Projector's performance.

Model Number

8767A/8070/8771

Optical

LCD Panel

Resolution

0.7" p-Si TFT active-matrix (with Micro Lens Array on 8767A only)

8767A/8771: 1024

768 pixels* native, up to UXGA.

8070: 800

600 pixels* native, up to UXGA with Advanced AccuBlend

Lens

8767A/8070/8771: Manual zoom and manual focus

F1.7 - 2.0 f=21.6 - 25.9 mm

Lamp

8767A/8070: 180W DC lamp (150W Eco mode)

8771: 130W DC lamp (110W Eco mode)

21 - 300 inches / 0.5 - 7.6 m

Image Size (Diagonal)

Projection Distance

Projection Angle

Keystone Correction

2.4 - 35.89 ft / 0.73 - 10.9 m

Tele: 9.5° - 9.9°/ Wide: 11.5° - 12.0°

+/- 30° Vertical (auto)

Electrical

Inputs

2 RGB/Component (D-Sub 15 Pin),

1 S-Video (DIN 4 Pin), 1 Video (RCA), 2 (L/R) RCA Audio,

1 Stereo Mini Audio, 1 PC Control (DIN 8 Pin)

Outputs

Video Compatibility

1 RGB (D-Sub 15 Pin), 1 Stereo Mini Audio (not available on VT47)

NTSC, NTSC4.43, PAL, PAL-60, PAL-N, PAL-M, SECAM,

HDTV: 1080i, 1080i/50Hz, 720p, 576p, 480p, 480i/60Hz

Horizontal: 15 kHz to 100 kHz (RGB: 24 kHz or over)

Vertical: 50 Hz to 120 Hz

Scan Rate

Video Bandwidth

RGB: 80 MHz (-3dB)

Color Reproduction

Horizontal Resolution

16.7 million colors simultaneously, Full color

NTSC / NTSC4.43/PAL/PAL-M/PAL-N/PAL60: 540 TV lines

SECAM: 300 TV lines

YCbCr: 800 TV lines

RGB: 8767A/8771: 1024 dots (H)

768 dots (V),

8070: 800 dots (H)

600 dots (V)

External Control

Sync Compatibility

Built-in Speaker

RS232, IR

Separate Sync / Composite Sync / Sync on G

1W (monaural)

* Effective pixels are more than 99.99%.

Download from Www.Somanuals.com. All Manuals Search And Download.

7. Appendix

Power Requirement

Input Current

100 - 240V AC, 50 / 60 Hz

8767A/8070: 2.7 - 1.4A (100 - 240V AC)

8771: 2.1 - 1.2A (100 - 240V AC)

Power Consumption

8767A/8070: 8W in Standby mode /

250W in Lamp Normal mode / 200W in Lamp Eco mode

8771: 8W in Standby mode /

190W in Lamp Normal mode / 155W in Lamp Eco mode

Mechanical

Installation Orientation

Dimensions

Desktop/Front, Desktop/Rear, Ceiling/Front, Ceiling/Rear

11.6" (W)

3.7" (H)

10.2" (D)

294mm (W)

93mm (H)

260mm (D)

(not including protrusions)

Net Weight

6.5 lbs / 2.9 kg

Environmental Considerations Operational Temperatures : 41° to 95°F (5° to 35°C),

20% to 80% humidity (non-condensing)

Storage Temperatures : 14° to 122°F (-10° to 50°C),

20% to 80% humidity (non-condensing)

Regulations

For United States:

UL Approved (UL 60950)

Meets FCC Class B requirements

For Canada:

UL Approved (CSA 60950)

Meets DOC Canada Class B requirements

For Australia/New Zealand:

Meets AS/NZS CISPR.22 Class B

For Europe:

Meets EMC Directive (EN55022, EN55024, EN61000-3-2, EN61000-3-3)

Meets Low Voltage Directive (EN60950, TUV GS Approved)

For additional information visit:

US : http://www.dukcorp.com/av

The specifications are subject to change without notice.

Download from Www.Somanuals.com. All Manuals Search And Download.

7. Appendix

ᕣ Cabinet Dimensions

A C I N

M O N I T O R O U T

L / M O N O

P C C O N T R O L

A U D I O O U T A U D I O

S - V I D E O I N

V I D E O I N

A U D I O L / M O N O

C O M P U T E R

I N A U D I O

C O M P U T E R I N

A D J .

A U T O

O N / S T A N D B Y

S E L E C T

C O M P U T E R - 2 C O M P U T E R - 1 S - V I D E O

V I D E O

P O W E R

S T A T U S

L A M P

Z O O M

F O C U S

294 (11.6)

71.5 (2.8)

Lens center

Unit: mm (inch)

Download from Www.Somanuals.com. All Manuals Search And Download.

7. Appendix

Download from Www.Somanuals.com. All Manuals Search And Download.

7. Appendix

ᕤ Pin Assignments of D-Sub COMPUTER Input Connector

Mini D-Sub 15 Pin Connector

Pin No. RGB Signal (Analog)

YCbCr Signal

Red

15 14 13 12 11

Green or Sync on Green

Blue

Ground

Red Ground

Green Ground

Blue Ground

Signal Level

Video signal : 0.7Vp-p (Analog)

Sync signal : TTL level

Cr Ground

Y Ground

Cb Ground

No Connection

Sync Signal Ground

SCART Sync

Bi-directional DATA (SDA)*

Horizontal Sync or Composite Sync

Vertical Sync

Data Clock*

* Only COMPUTER 1 input connector supported.

Download from Www.Somanuals.com. All Manuals Search And Download.

7. Appendix

ᕥ Compatible Input Signal List

Signal

Resolution

( Dots )

Frequency H.

( kHz )

Refresh Rate

( Hz )

59.94

NTSC

PAL

PAL60

SECAM

VESA

–

15.734

15.625

15.734

15.625

31.47

640

480

640

480

IBM

31.47

MAC

VESA

IBM

VESA

IBM

VESA

IBM

VESA

MAC

VESA

MAC

VESA

MAC

SUN

SGI

VESA

MAC

SUN

640

480

640

480

640

480

640

480

640

480

640

480

640

480

720

350

720

400

720

350

720

400

800

600

800

600

800

600

800

600

800

600

832

624

1024

768

1024

768

1024

768

1024

768

1024

768

1024

768

1152

864

1152

870

1152

900

1152

900

1280

960

1280

1024

1280

1024

1280

1024

1280

1024

1280

1024

1280

1024

1400

1050

1920

1080

–

31.47

34.97

37.86

37.5

66.67

72.81

85.01

70.09

85.04

87.85

56.25

60.32

72.19

85.06

74.55

43 Interlaced

70.07

74.93

75.03

75.06

65.95

76.05

60.02

65.18

72.01

76.11

75.03

85.02

–

60 Progressive

60 Interlace

50 Interlace

60 Progressive

59.94 Progressive

39.375

43.269

31.469

37.927

39.44

35.16

37.879

48.077

46.88

53.674

49.725

35.5

48.363

56.476

60.241

60.023

68.677

67.5

68.681

61.796

71.736

63.981

69.89

78.125

81.13

79.976

91.146

–

VESA

SXGA+

HDTV (1080p)

SDTV(576i)(625i)

SDTV(576p)(625p)

HDTV (1080i)(1125i)

HDTV (720p)(750p)

SDTV (480p)(525p)

VESA

DVD YCbCr

67.5

15.6

31.5

–

1920

1080

1920

1080

1280

720

–

1600

1200

1600

1200

1600

1200

1600

1200

–

33.75

28.125

31.47

75.0

81.25

87.5

93.75

15.734

15.625

# *

59.94 Interlaced

50 Interlaced

–

: Images in above flagged with # are compressed.

@ : Images in above flagged with @ are compressed.

: Images in above flagged with * are not supported on other models.

NOTE: Some composite sync signals may not be displayed correctly.

Signals other than those specified in the table above may not be displayed correctly. If this should happen, change

the refresh rate or resolution on your PC. Refer to Display Properties help section of your PC for procedures.

UXGA (1600

1200) is supported for separate sync signal only.

Download from Www.Somanuals.com. All Manuals Search And Download.

7. Appendix

ᕦ PC Control Codes and Cable Connection

PC Control Codes

Function

Code Data

POWER ON

02H

00H

02H

00H

02H

03H

01H

12H

13H

14H

15H

POWER OFF

01H

03H

10H

11H

12H

13H

INPUT SELECT COMPUTER 1

INPUT SELECT COMPUTER 2

INPUT SELECT VIDEO

INPUT SELECT S-VIDEO

PICTURE MUTE ON

PICTURE MUTE OFF

SOUND MUTE ON

SOUND MUTE OFF

01H

02H

06H

0BH

09H

0AH

0EH

13H

NOTE: Contact your local dealer for a full list of the PC Contorol Codes if needed.

Cable Connection

Communication Protocol

Baud rate ........................................ 19200 bps

Data length ..................................... 8 bits

Parity.............................................. No parity

Stop bit .......................................... One bit

X on/off .......................................... None

Communications procedure ........... Full duplex

NOTE: Depending on the equipment, a lower baud rate may be recommended for long cable runs.

Download from Www.Somanuals.com. All Manuals Search And Download.

7. Appendix

PC Control Connector (DIN-8P)

To RxD of PC

To GND of PC

To TxD of PC

NOTE: Pins 2, 3, 5, 6 and 8 are used inside the projector.

Download from Www.Somanuals.com. All Manuals Search And Download.

7. Appendix

¶ Optional Presentation Remote Control Kit (PR52KIT)

The PR52KIT is an optional remote control kit for operating your projector and performing your computer mouse

operations.

Package List

• RD-408E remote control unit....... 1 • AAA batteries ................... 2

• Mouse receiver............................ 1 • User's manual .................. 1

Part Names and Functions of the Remote Control

1. Infrared Transmitter/Laser Pointer

Transmits an infrared signal when any button other

than LASER is pressed.

Direct the remote control toward the remote sensor

on the projector cabinet.

Beams a laser light when the Laser button is pressed.

OFF

POWER

LASER

PAGE

MAGNIFY

POINTER

CAUTION:

DOWN

* Do not look into the laser pointer while it is on.

* Do not point the laser beam at a person.

2. Remote Jack

Not available on this model.

3. LED

Flashes when any button is pressed.

PICTURE

ASPECT

VIEWER

SLIDE

SOURCE

AUTO ADJ.

HELP

4. POWER ON Button

When the main power is on, you can use this button

to turn your projector on.

NOTE: To turn on the projector, press and hold the

POWER ON button for a minimum of two seconds.

PIC-MUTE

VOLUME

ZOOM

FOCUS

FREEZE

3D REFORM

5. POWER OFF Button

You can use this button to turn your projector off.

NOTE: To turn off the projector, press the POWER OFF

button twice.

PJ OFF MOUSE

6. MAGNIFY (+)(–) Buttons

Use these buttons to adjust the image size.

The image can be magnified about the center of the

screen up to 400%.

7. LASER Button

Press and hold this button to activate the laser pointer.

When lit, you can use the laser to draw your audience's

attention to a red dot that you can place on any ob-

ject.

Download from Www.Somanuals.com. All Manuals Search And Download.

7. Appendix

8. POINTER Button

19. AUTO ADJ. Button

Not available on this model.

Use this button to adjust an RGB source for an opti-

mal picture.

9. PAGE UP/DOWN Buttons*

Use these buttons to operate your computer with the

supplied remote mouse receiver. You can use these

buttons to scroll the viewing area of the window or to

move to the previous or next slide in PowerPoint on

your computer.

20. VIEWER Button

Not available on this model.

21. SLIDE +/- Buttons

Not available on this model.

10. MENU Button

22. PIC-MUTE Button

Displays the menu for various settings and adjust-

ments.

This button turns off the image and sound for a short

period of time. Press again to restore the image and

sound.

11. Mouse Button

In Mouse mode*, this button works as your computer

23. HELP Button

mouse.

Provides the Information screen.

In Projector mode, this button is used for projector’s

menu operation and moving the magnified image.

24. VOLUME +/– Buttons

Press (+) to increase the volume and (–) to decrease

12. ENTER Button

it.

Executes your menu selection and activates items se-

lected from the menu.

25. FOCUS +/- Buttons

Not available on this model.

13. EXIT Button

Returns to the previous menu.

While you are in the main menu, pressing this button

will close the menu.

26. ZOOM +/- Buttons

Use to finely adjust the image on the screen.

14. L-CLICK Button*

27. FREEZE Button

Works as the mouse left button when the supplied

remote mouse receiver is connected with your com-

puter.

This button will freeze a picture. Press again to re-

sume motion.

28. 3D REFORM Button

15. R-CLICK Button*

Not available on this model.

Works as the mouse right button when the supplied

remote mouse receiver is connected with your com-

puter.

29. PJ ̇ OFF ̈ MOUSE Slide Switch

Use to switch mouse button operation modes between

Mouse and Projector. Setting to OFF will disable all

the buttons on the remote control.

16. PICTURE Button

Press this button to display the Picture window. Each

time this button is pressed, the option will be changed:

Wall Color → Picture Management → Brightness →

Contrast → Sharpness → Color → Hue

*NOTE: The PAGE UP/DOWN, L-CLICK, R-CLICK and MOUSE

(as computer mouse) buttons are available only when the PJ

̇ OFF ̈ MOUSE Slide Switch is set to MOUSE.

17. SOURCE Button

Use this button to select a video source such as a

PC, VCR or DVD player.

Press and release this button quickly to display the

Source List.

Each time this button is pressed for a minimum of

ONE second, the input source will change.

If no input signal is present, the input will be skipped.

18. ASPECT Button

Press this button to display the Aspect Ratio select

screen.

Download from Www.Somanuals.com. All Manuals Search And Download.

7. Appendix

Battery Installation

1 _{Remove the battery cover.}

2 _{Remove both old batteries and}

3 _{Slip the cover back over the bat-}

teries until it snaps into place.

NOTE: Do not mix different types of

batteries or new and old batteries.

NOTE: Do not pull the battery

cover by force. Doing so can

result in it coming off.

install new ones (AAA). Ensure

that you have the batteries' po-

larity (+/ –) aligned correctly.

Operating Range for Wireless Remote Control

Remote control

Remote sensor on projector cabinet

7m/22 feet

30°

7m/22 feet

•

The infrared signal operates by line-of-sight up to a distance of about 22 feet/7 m and within a 60-degree angle of

the remote sensor on the projector cabinet.

The projector will not respond if there are objects between the remote control and the sensor, or if strong light falls

on the sensor.

Weak batteries will also prevent the remote control from properly operating the projector.

Remote Control Precautions

•

Handle the remote control carefully.

If the remote control gets wet, wipe it dry immediately.

Avoid excessive heat and humidity.

If you will not be using the remote control for a long time, remove the batteries.

Do not place the batteries upside down.

Do not use new and old batteries together, or use different types of batteries together.

Download from Www.Somanuals.com. All Manuals Search And Download.

7. Appendix

Using the Laser Pointer

You can use the laser to draw your audience's attention to a red dot that you can place on any object.

CAUTION:

• Do not look into the laser pointer while it is on.

• Do not point the laser beam at a person.

• Do not allow children to use the laser pointer.

Press and hold the LASER button to activate the laser pointer.

LASER

To disable the laser pointer, set the function switch to “Off”.

Decide whether to enable or disable laser, then set the switch as necessary using the tip of a thin ball-point pen. On

this model, the other selector switch is not used.

Laser enable/disable

switch

OFF

Not used

On: Enabled (the laser lights when the LASER button is pressed) [Factory default]

Off: Disabled (the laser does not light even when the LASER button is pressed)

Disable the laser when using in an environment in which the unit is accessible to children.

Using Remote Mouse Receiver (8767A/8070 only)

See page 34.

Download from Www.Somanuals.com. All Manuals Search And Download.

7. Appendix

º Troubleshooting Check List

Before contacting your dealer or service personnel, check the following list to be sure repairs are needed also by

referring to the “Troubleshooting” section in your user’s manual. This checklist below will help us solve your problem

more efficiently.

* Print the following pages.

Frequency of occurrence Ⅺ always Ⅺ sometimes (How often?_____________________) Ⅺ other (__________________)

Power

No power (POWER indicator does not light green) See also “Sta-

tus Indicator (STATUS)”.

Shut down during operation.

Power cable's plug is fully inserted into the wall outlet.

Lamp cover is installed correctly .

Power cable's plug is fully inserted into the wall outlet.

Main power switch is pressed to the ON position.

Lamp cover is installed correctly .

Power Management is turned off (only models with the Power

Management function).

Lamp Hour Meter (lamp operation hours) was cleared after

lamp replacement.

Sleep Timer is turned off (only models with the Sleep Timer

function ).

No power even though you press and hold the POWER button

for a minimum of 2 seconds.

Video and Audio

No image is displayed from your PC or video equipment to the

projector.

Parts of the image are lost.

Still unchanged even though you press the AUTO ADJUST but-

ton.

Still no image even though you connect the projector to the PC

first, then start the PC.

Still unchanged even though you carry out “Reset” in the

projector’s menu.

Enabling your notebook PC’s signal output to the projector.

•

A combination of function keys will enable/disable the ex-

ternal display. Usually, the combination of the “Fn” key along

with one of the 12 function keys turns the external display

on or off.

Image is shifted in the vertical or horizontal direction.

Horizontal and vertical positions are correctly adjusted on a

computer signal.

Input source's resolution and frequency are supported by the

projector.

No image (blue background, logo, no display).

Still no image even though you press the AUTO ADJUST but-

ton.

Some pixels are lost.

Image is flickering.

Still no image even though you carry out “Reset” in the

projector’s menu.

Still unchanged even though you press the AUTO ADJUST but-

ton.

Signal cable's plug is fully inserted into the input connector

Still unchanged even though you carry out “Reset” in the

projector’s menu.

A message appears on the screen.

( _____________________________________________ )

Image shows flickering or color drift on a computer signal.

Image appears blurry or out of focus.

The source connected to the projector is active and available.

Still no image even though you adjust the brightness and/or

the contrast.

Still unchanged even though you checked the signal’s resolu-

tion on PC and changed it to projector’s native resolution.

Input source's resolution and frequency are supported by the

projector.

Still unchanged even though you adjusted the focus.

No sound.

Image is too dark.

Audio cable is correctly connected to the audio input of the

projector.

Remains unchanged even though you adjust the brightness

and/or the contrast.

Image is distorted.

Still unchanged even though you adjusted the volume level.

AUDIO OUT is connected to your audio equipment (only mod-

els with the AUDIO OUT connector).

Image appears to be trapezoidal (unchanged even though you

carry out the “Keystone" or “3D Reform” adjustment).

Other

Remote control does not work.

Buttons on the projector cabinet do not work ( only models with

the Key Lock function).

No obstacles between the sensor of the projector and the re-

mote control.

Cabinet Button Lock is not turned on or is disabled in the menu.

Projector is placed near a fluorescent light that can disturb the

infrared remote controls.

Still unchanged even though you press and hold the EXIT but-

ton for a minimum of 10 seconds.

One or more remote sensors are enabled (only models with

the Remote Sensor Selection function).

Batteries are new and are not reversed in installation.

If present on the remote control, projector selector switch is

not used.

Download from Www.Somanuals.com. All Manuals Search And Download.

7. Appendix

In the space below please describe your problem in detail.

Information on application and environment where your projector is used

Projector

Installation environment

Screen size:

Model number:

inch

Serial No.:

Screen type: Ⅺ White matte Ⅺ Beads Ⅺ Polarization

Ⅺ Wide angle Ⅺ High contrast

Date of purchase:

Lamp operating time (hours):

Lamp Mode:

Throw distance:

feet/inch/m

Ⅺ Normal Ⅺ Eco

Orientation: Ⅺ Ceiling mount Ⅺ Desktop

Power outlet connection:

Information on input signal:

Horizontal synch frequency

Vertical synch frequency

Synch polarity

[

] kHz

] Hz

Ⅺ Connected directly to wall outlet

Ⅺ Connected to power cord extender or other (the num-

ber of connected equipment______________)

H Ⅺ (+) Ⅺ (–)

Ⅺ Connected to a power cord reel or other (the number

V Ⅺ (+) Ⅺ (–)

of connected equipment______________)

Synch type

Ⅺ Separate Ⅺ Composite

Ⅺ Sync on Green

Computer

STATUS Indicator:

Steady light

Manufacturer:

Ⅺ Orange Ⅺ Green

Model number:

Notebook PC Ⅺ / Desktop Ⅺ

Native resolution:

Refresh rate:

Flashing light

[

] cycles

Remote control model number:

Video adapter:

Other:

Projector

DVD player

Video equipment

Signal cable

VCR, DVD player, Video camera, Video game or other

Standard or other manufacturer’s cable?

Model number:

Distribution amplifier

Model number:

Switcher

Length:

inch/m

Manufacturer:

Model number:

Adapter

Model number:

Download from Www.Somanuals.com. All Manuals Search And Download.

Audio Visual Products

Dukane Corporation

Audio Visual Products Division

2900 Dukane Drive

Phone: (630) 762-4040

Orders: (800) 676-2485

Fax: (630) 584-5156

St. Charles, IL 60174-3395

E-mail: [email protected]

Parts & Service: (800) 676-2487

Fax: (630) 584-0984

Part # 401-8767A_8771_8070-00

Download from Www.Somanuals.com. All Manuals Search And Download.

Control4 Home Theater Server C4 HC500 E B User Manual
Cuisinart Coffeemaker DCC2400U User Manual
Delta Electronics Network Card SPBD 155E4J1RD User Manual
Duracell Battery Charger Ni MH User Manual
Dynamat TV Video Accessories 2036 User Manual
EdgeStar Beverage Dispenser KC2000SSTWIN User Manual
EVGA Computer Hardware 730I User Manual
Extron electronic Stereo Amplifier ASA 204 User Manual
Furman Sound Power Supply 16 E User Manual
Furman Sound Power Supply IT 1210 User Manual