Portable LCD Projector
Models 8755D, 8755D-RJ & 8065
USER’S MANUAL
401-8755D-01
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector
, 8755D-RJ, & 8065
8755D
User's Manual – Operating Guide
Thank you for purchasing this projector.
About this manual
Various symbols are used in this manual. The meanings of these symbols are
described below.
WARNING This symbol indicates information that, if ignored, could possibly
result in personal injury or even death due to incorrect handling.
CAUTION This symbol indicates information that, if ignored, could possibly
result in personal injury or physical damage due to incorrect
handling.
Please refer to the pages written following this symbol.
NOTE • The information in this manual is subject to change without notice.
• The manufacturer assumes no responsibility for any errors that may appear in this manual.
• The reproduction, transfer or copy of all or any part of this document is not permitted
without express written consent.
Trademark acknowledgment
• VGA and XGA are registered trademarks of International Business Machines Corporation.
• Apple and Mac are registered trademarks of Apple Computer, Inc.
• VESA and SVGA are trademarks of Video Electronics Standard Association.
• Windows is a registered trademark of Microsoft Corporation.
All other trademarks are the properties of their respective owners.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Content
Content
About this manual. . . . . . . . . . 1 EASY Menu. . . . . . . . . . . . . . . . . . 25
Aspect, Keystone, Mode, Brightness,
Contrast, Color, Tint, Sharpness,
Whisper, Mirror, Reset, Filter time,
Content . . . . . . . . . . . . . . . . . . 2
Projector features. . . . . . . . . . 3
Preparations . . . . . . . . . . . . . . 3
Language,
Go to advanced menu
About contents of package . . . . . . . 3
Fastening the lens cover . . . . . . . . . 3
PICTURE Menu. . . . . . . . . . . . . . . 27
Brightness, Contrast, Gamma,
Color temp, Color, Tint, Sharpness,
Progressive, My memory
Part names . . . . . . . . . . . . . . . 4
Projector . . . . . . . . . . . . . . . . . . . . . 4
Control buttons . . . . . . . . . . . . . . . . 6
Remote control . . . . . . . . . . . . . . . . 6
IMAGE Menu. . . . . . . . . . . . . . . . . 30
Aspect, Over scan, V. position, H. position,
H. phase, H. size, Auto adjust execute
Setting up . . . . . . . . . . . . . . . . 7
Arrangement . . . . . . . . . . . . . . . . . . 8
Adjusting the projector's elevator . . 9
Using the Security Bar. . . . . . . . . . 10
Connecting your devices. . . . . . . . .11
Connecting power supply . . . . . . . 14
INPUT Menu . . . . . . . . . . . . . . . . . 32
Color space, Component, Video format,
Frame lock, Information
SETUP Menu. . . . . . . . . . . . . . . . . 34
Keystone, Whisper, Mirror, Volume,
Audio
Remote control . . . . . . . . . . . 15
Putting batteries . . . . . . . . . . . . . . 15
Using the remote control . . . . . . . . 16
SCREEN Menu . . . . . . . . . . . . . . . 35
Language, Menu position, OSD bright.,
Blank, Start up, MyScreen,
Power on/off . . . . . . . . . . . . . 17
Turning on the power. . . . . . . . . . . 17
Turning off the power. . . . . . . . . . . 17
MyScreen lock, Message
OPTION Menu. . . . . . . . . . . . . . . . 38
Operating . . . . . . . . . . . . . . . 18
Adjusting the volume. . . . . . . . . . . 18
Temporarily muting the sound . . . . 18
Selecting an input signal . . . . . . . . 18
Searcting an input signal. . . . . . . . 19
Selecting an aspect ratio. . . . . . . . 19
Adjusting the zoom and focus . . . . 19
Using the automatic adjustment feature . 20
Adjusting the position . . . . . . . . . . 20
Correcting the keystone distortions 21
Using the magnify feature . . . . . . . 21
Freezing the screen. . . . . . . . . . . . 22
Temporarily blanking the screen . . 22
Operating the computer screen. . . 23
search, Auto off, Lamp time,
Filter time, Service
Auto
Maintenance . . . . . . . . . . . . . 40
Lamp . . . . . . . . . . . . . . . . . . . . . . . 40
Air filter . . . . . . . . . . . . . . . . . . . . . 42
Other care . . . . . . . . . . . . . . . . . . . 44
Internal clock battery replacement
(8755D-RJ only) . . . . . . . . . . . 45
Troubleshooting . . . . . . . . . . 47
Related messages. . . . . . . . . . . . . 47
Regarding the indicator lamps. . . . 48
Phenomena that may easily be
mistaken for machine defects . . . . 50
Warranty and after-service. . . 53
Specifications . . . . . . . . . . . . 53
Multifunctional settings . . . . 24
Using the menu function . . . . . . . . 24
8755D-RJ Network Functions &
Operation . . . . . . . . . . . . . . . . . . 55
Technical Information Section. . 97
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector features / Preparations
Projector features
This projector is used to project various computer signals as well as NTSC/PAL/
SECAM, Component (SD, HD) video signals onto a screen. It requires just a little
space for installation and gets a large image from short distance.
High Brightness
Newly developed 180W UHB (Ultra High Brightness) lamp gives you a higher
brightness image on a screen. The image can be still kept as bright and clean
enough for use in bright rooms.
Low Noise
WHISPER mode is available for reducing acoustic noise to realize quieter
operation. It is perfect for use in low luminance rooms where low noise is more
important than brightness.
Rich Connectivity
This projector has a variety of I/O ports. It can be easily connected to many
signal sources like PC, DVD and so on. The rich connectivity provides you
more options to make your presentation impressive.
Compact Body
Even with its many features, this projector is extremely compact and slim,
which gives you more flexibility and usability to use it where you want.
Preparations
NOTE • Keep the original packing materials for future reshipment. For
moving the projector, be sure to use the original packing materials. Use special
caution for the lens part.
Fastening the lens cover
To avoid losing the lens cover, please fasten it the lens cap to the projector using
the strap.
Strap ring
Strap
Bottom side
Strap hole
1. Fix the strap to the strap ring of the lens cover.
Put the strap into the groove on the rivet.
2.
3.
Push the rivet into the strap hole.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Part names
Part names
Projector
Control buttons ( 6)
Lamp cover ( 41)
Remote sensor ( 16)
(Lamp unit is inside.)
Speaker
Zoom knob ( 19)
Security bar ( 10)
Focus ring ( 19)
Use for attaching a
（
commercial anti-theft
chain or wire.)
Vent ( 7)
Elevator button ( 9)
Lens ( 17)
Front-Right side
Elevator foot ( 9)
Lens cover ( 3)
Filter cover ( 42)
(Air filter and intake vent
are inside.)
Bottom side
WARNING ►During use or immediately after use, do not touch around the
lamp and vents of the projector. () It could cause a burn.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Part names
Power switch ( 17)
AC inlet ( 14)
Elevator button ( 9)
Ports (See below.)
Elevator foot ( 9)
Rear-Left side
Vent ( 7)
CONTROL port ( 12)
Restart switch (*) ( 48)
AUDIO-OUT port ( 12)
RGB IN1 port ( 12)
AUDIO IN2 L/R port ( 13)
RGB IN2 /RGB OUT port ( 12)
(In the default setting, the
(Use the RGB IN OUT switch to select
RGB IN2 or RGB OUT for this port.)
RGB IN2 port: Inputs the RGB signal from
a PC.
AUDIO IN2 L/R port is the audio
port for the VIDEO, S-VIDEO
and COMPONENT VIDEO
ports, however it is possible to
RGB OUT port: When connected to a
monitor, outputs the signal input via RGB
IN1.
change the settings. 34)
COMPONENT
AUDIO IN2
R
VIDEO ports ( 13)
Y
USB port ( 12)
Y
CONTROL
RGB IN1
RGB IN2
RGB OUT
USB
CB/PB
CR/PR
AUDIO OUT
C
C
B
R
/
P
B
R
L
K
AUDIO IN1
/P
VIDEO
S-VIDEO
LINK O
ACT O
VIDEO port ( 13)
S-VIDEO port ( 13)
Ports
RGB IN OUT switch ( 12)
AUDIO IN1 port ( 12)
Use this button to select either RGB IN2
or RGB OUT for the corresponding port.
When this switch is not pushed in, RGB
IN2 is selected.
(In the default setting, the AUDIO
IN1 port is the audio port for the
RGB IN1 and RGB IN2 ports,
however, it is possible to change
When this switch is pushed in, RGB OUT
is selected.
the settings. 34)
LAN Port
RJ-45 Jack, Model 8755D-RJ Only!
Used for Ethernet input/output.
This port is used when utilizing network functions.
NOTE (*) About Restart switch: This projector is controlled by an internal
microprocessor. Under certain exceptional circumstances, the projector may not
operate correctly and the microprocessor will need to be reset. In such a case,
please push the Restart switch by using a tooth pick or similar, and before
turning on again, let the projector cool down at least 10 minutes without
operating. Only push the Restart switch in these exceptional instances.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Part names
Control buttons
LAMP indicator ( 46, 47)
TEMP indicator ( 46, 47)
Cursor buttons
POWER indicator ( 17)
▲,▼,◄,► ( 24)
STANDBY/ON button
(
17)
INPUT button ( 18)
Remote control
SEARCH button ( 19)
STANDBY/ON button ( 17)
RGB button ( 18)
AUTO button ( 20)
SEARCH
AUTO
VIDEO
RGB
VIDEO button ( 19)
BLANK button ( 22)
BLANK
ASPECT
ASPECT button ( 19)
PAGE UP button ( 23)
MAGNIFY
PAGE UP
VOLUME
MUTE
HOME
END
ON
HOME button ( 23)
VOLUME button ( 18)
PAGE DOWN
MAGNIFY
OFF
MUTE button ( 18)
ON button ( 21)
FREEZE
KEYSTONE
OFF button ( 21)
PAGE DOWN button ( 23)
END button ( 23)
KEYSTONE button ( 21)
MENU
FREEZE button ( 22)
POSITION
MENU button ( 24)
POSITION button ( 20)
ENTER
Cursor buttons
ESC button ( 24)
RESET
ESC
▲,▼,◄,► ( 24)
ENTER button ( 24)
RESET button ( 24)
Battery cover ( 15)
(on the back)
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up
Setting up
WARNING ►Place the projector in a stable position horizontally. A fall or
a turnover could cause an injury and/or damage to the projector. Using a
damaged projector could result in a fire and/or an electric shock.
• Do not place the projector on an unstable, slant or vibrant surface such as a
wobbly or inclined stand.
• Do not place the projector in the side/front/rear-up position, except when
cleaning the air filter.
►Place the projection in a cool place, and pay attention enough to ventilation.
The high temperature of the projector could cause a fire, a burn and/or
malfunction to the projector.
• Do not stop up, block and cover the projector's vents.
• Keep a space of 30 cm or more between the sides and other objects such as
walls.
• Do not place the projector on a metallic thing or anything weak in heat.
• Do not place the projector on a carpet, cushion or bedding.
• Do not place the projector in direct sunlight or near a hot object such as a
heater.
• Put nothing about lens and vents of the projector. Put nothing on the projector.
• Put nothing that is sucked or sticks to the bottom of projector. This projector
has some intake vents also on the bottom.
►Do not place the projector on the place that gets wet. Damping the projector
or inserting liquid in the projector could cause a fire, an electric shock and/or
malfunction to the projector.
• Do not place the projector in a bathroom or the outdoors.
• Put nothing containing the liquid near the projector.
CAUTION ►Avoid a smoky, humid or dusty place. Placing the projector
in such place could cause a fire, an electric shock and/or malfunction to the
projector.
• Do not place the projector near a humidifier, a smoking space or a kitchen.
►Adjust the direction of the projector to keep the light from directly hitting the
projector's remote sensor.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up
Arrangement
Refer to the illustrations and tables below to determine the screen size and projection distance.
The values shown in the table are calculated for a full size screen: TBD : 800×600,
8755D : 1024×768
(b)
(a) The screen size (diagonal)
(b) Distance from the projector to the screen (±10%)
(c) The height of the screen (±10%)
(c) up
4:3
(a)
16:9
(a)
(c) down
For the model 8065
4 : 3 screen
16 : 9 screen
(a) Screen
size
[inch (m)]
(b) Projection distance
[m (inch)]
min. max.
(c) Screen height
(b) Projection distance
(c) Screen height
[cm (inch)]
[m (inch)]
min.
[cm (inch)]
down
up
max.
down
-1 (0)
up
30 (0.8) 0.9 (36) 1.1 (43)
40 (1.0) 1.2 (48) 1.5 (57)
50 (1.3) 1.5 (60) 1.8 (72)
60 (1.5) 1.8 (72) 2.2 (87)
1.0 (39) 1.2 (47)
5
(2)
(2)
(3)
(4)
41 (16)
39 (15)
6
8
9
55 (22) 1.3 (52) 1.6 (63) -2 (-1) 51 (20)
69 (27) 1.7 (65) 2.0 (79) -2 (-1) 64 (25)
82 (32) 2.0 (79) 2.4 (94) -2 (-1) 77 (30)
96 (38) 2.3 (92) 2.8 (110) -3 (-1) 90 (35)
70 (1.8) 2.1 (84) 2.6 (101) 11 (4)
80 (2.0) 2.4 (96) 2.9 (116) 12 (5) 110 (43) 2.7 (105) 3.2 (126) -3 (-1) 103 (41)
90 (2.3) 2.8 (109) 3.3 (130) 14 (5) 123 (49) 3.0 (118) 3.6 (142) -4 (-1) 116 (46)
100 (2.5) 3.1 (121) 3.7 (145) 15 (6) 137 (54) 3.3 (132) 4.0 (158) -4 (-2) 129 (51)
120 (3.0) 3.7 (145) 4.4 (174) 18 (7) 165 (65) 4.0 (158) 4.8 (190) -5 (-2) 154 (61)
150 (3.8) 4.6 (182) 5.5 (218) 23 (9) 206 (81) 5.0 (198) 6.0 (238) -6 (-2) 193 (76)
200 (5.1) 6.2 (242) 7.4 (291) 30 (12) 274 (108) 6.7 (264) 8.1 (317) -8 (-3) 257 (101)
250 (6.4) 7.7 (303) 9.3 (364) 38 (15) 343 (135) 8.4 (330) 10.1 (397) -10 (-4) 322 (127)
300 (7.6) 9.2 (364) 11.1 (437) 46 (18) 411 (162) 10.1 (397) 12.1 (476) -12 (-5) 386 (152)
For the model 8755D & 8755D-RJ
4 : 3 screen
16 : 9 screen
(a) Screen
size
[inch (m)]
(b) Projection distance
[m (inch)]
min. max.
(c) Screen height
(b) Projection distance
[m (inch)]
min. max.
(c) Screen height
[cm (inch)]
[cm (inch)]
down
up
down
-1 (0)
up
30 (0.8) 0.9 (36) 1.1 (43)
40 (1.0) 1.2 (48) 1.5 (58)
50 (1.3) 1.5 (60) 1.8 (73)
60 (1.5) 1.8 (73) 2.2 (87)
1.0 (39) 1.2 (47)
5
(2)
(2)
(3)
(4)
41 (16)
39 (15)
6
8
9
55 (22) 1.3 (52) 1.6 (63) -2 (-1) 51 (20)
69 (27) 1.7 (66) 2.0 (79) -2 (-1) 64 (25)
82 (32) 2.0 (79) 2.4 (95) -2 (-1) 77 (30)
96 (38) 2.4 (93) 2.8 (111) -3 (-1) 90 (35)
70 (1.8) 2.2 (85) 2.6 (102) 11 (4)
80 (2.0) 2.5 (97) 3.0 (117) 12 (5) 110 (43) 2.7 (106) 3.2 (127) -3 (-1) 103 (41)
90 (2.3) 2.8 (109) 3.3 (132) 14 (5) 123 (49) 3.0 (119) 3.6 (143) -4 (-1) 116 (46)
100 (2.5) 3.1 (122) 3.7 (146) 15 (6) 137 (54) 3.4 (133) 4.0 (159) -4 (-2) 129 (51)
120 (3.0) 3.7 (146) 4.5 (176) 18 (7) 165 (65) 4.0 (159) 4.9 (192) -5 (-2) 154 (61)
150 (3.8) 4.6 (183) 5.6 (220) 23 (9) 206 (81) 5.1 (200) 6.1 (240) -6 (-2) 193 (76)
200 (5.1) 6.2 (244) 7.5 (294) 30 (12) 274 (108) 6.8 (266) 8.1 (320) -8 (-3) 257 (101)
250 (6.4) 7.8 (306) 9.3 (367) 38 (15) 343 (135) 8.5 (333) 10.2 (400) -10 (-4) 322 (127)
300 (7.6) 9.3 (367) 11.2 (441) 46 (18) 411 (162) 10.2 (400) 12.2 (480) -12 (-5) 386 (152)
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up
Adjusting the projector's elevator
CAUTION ►If you press the elevator button without holding the projector,
the projector might crash down, overturn, smash your fingers and possibly
result in malfunction. To prevent damaging the projector and injuring yourself,
always hold the projector whenever using the elevator buttons to adjust the
elevator feet.
►Do not incline the projector rightward or leftward. Also do not incline it
backward or forward exceeding 9 degrees. Exceeding these range could cause
malfunction, and could shorten the lifetime of the consumables.
►Except for inclining by the elevator feet adjustment, place the projector
horizontally.
You can use the elevator feet to make adjustments if the surface on which you
need to set the projector is uneven or if you otherwise need to adjust the angle of
projection. The adjustment range of the elevator feet is 0 to 9 degrees.
Elevator feet
Elevator button
After making sure that the projector is cool adequately, press and hold in the
elevator buttons while holding the projector.
The elevator buttons and the elevator feet are on the both sides.
1.
2.
3.
Raise or lower the projector to the desired height and release the elevator
buttons.
When you release the elevator buttons, the elevator feet will lock into position.
If necessary, you can also finely adjust the height of the projector by twisting
the elevator feet by hand.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up
Using the Security Bar
WARNING ►Do not use the security bar to prevent the projector from
falling. Dropping or knocking over the projector may cause damage or injury.
CAUTION ►The security bar is not a comprehensive theft prevention
measure. It is intended to be used as an extra theft prevention measure.
A commercial anti-theft chain or wire can be attached to the security bar on the
projector.
How to attach
1.
An anti-theft chain or wire can be
attached as shown in the illustration.
(Anti-theft chains or wires of up to
10mm in diameter can be used)
Security Bar
Anti-theft chain or wire
[sold separately]
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up
Connecting your devices
CAUTION ►Turn off all devices prior to connecting them to the projector.
Attempting to connect a live device to the projector may generate extremely
loud noises or other abnormalities that may result in malfunction and/or damage
to the device and/or projector.
►Use the accessory cable or a designated-type cable for the connection.
Some cables have to be used with core set. A too long cable may cause a
certain picture degradation. Please consult with your dealer for details. For
cables that have a core only at one end, connect the core to the projector.
►Make sure that you connect devices to the correct port. Incorrect connection
may result in malfunction and/or damage to the device and/or projector.
NOTE • Whenever attempting to connect a laptop computer to the projector, be sure
to activate the laptop’s RGB external image output (set the laptop to CRT display or to
simultaneous LCD and CRT display). For details on how this is done, please refer to the
instruction manual of the corresponding laptop computer.
• Secure the screws on the connectors and tighten.
• Some computers may have multiple display screen modes. Use of some of these
modes will not be possible with this projector.
• For some RGB signal modes, the optional Mac adapter is necessary.
• When the image resolution is changed on a computer, depending on an input,
automatic adjustment function may take some time and may not be completed. In this
case, you may not be able to see a check box to select “Yes/No” for the new resolution
on Windows. Then the resolution will go back to the original. It might be recommended
to use other CRT or LCD monitors to change the resolution.
About Plug-and-Play capability
Plug-and-Play is a system composed of the computer, its operating system and
peripheral equipment (i.e. display devices). This projector is compatible with VESA DDC
2B. Plug-and-Play can be achieved by connecting this projector to a computer is VESA
DDC (display data channel) compatible.
• Please take advantage of this function by connecting the accessory RGB cable to the
RGB IN1 port (DDC 2B compatible). Plug-and-Play may not work properly if any other
type of connection is attempted.
• Please use the standard drivers in your computer as this projector is a Plug-and-Play
monitor.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up
Examples of connection with a computer
* In the default setting, the AUDIO IN1 port is the audio port for the RGB IN1 and RGB IN2
ports. To change the settings, refer to the AUDIO item in the SETUP menu. ( 34)
RGB cable
USB cable
AUDIO IN2
R
Y
CONTROL
RGB IN1
RGB IN2
RGB OUT
USB
A
C
C
B
R
/
P
B
L
K
AUDI
RGB out Audio out RS-232C USB
/P
R
VIDEO
S-VIDEO
RS-232C cable
Stereo mini
audio cable
Use the RGB IN OUT
switch to select
RGB IN2 (RGB IN2 is
selected if the switch is
not pushed in).
Stereo mini audio cable
AUDIO IN2
R
Audio out
RGB out
Y
CONTROL
RGB IN1
RGB IN2
RGB IN2
R
USB
AUDIO OUT
C
C
B
R
/
P
B
L
K
AUDIO IN1
/P
R
VIDEO
S-VIDEO
RGB cable
Use the RGB IN OUT switch to select RGB OUT
(RGB OUT is selected if the switch is pushed in).
Connecting to a monitor (output)
AUDIO IN2
R
Y
CONTROL
RGB IN1
RGB in
RGB IN2
R
USB
AUDIO OUT
C
C
B
R
/
P
B
L
K
AUDIO IN1
/P
R
VIDEO
S-VIDEO
RGB cable
Connecting to a speaker with amplifier (output)
AUDIO IN2
R
Y
Audio in
CONTROL
RGB IN1
RGB IN2
RGB OUT
USB
AUDIO OUT
C
C
B
/
P
B
L
K
AUDIO IN1
R
/P
R
VIDEO
S-VIDEO
Stereo mini audio cable
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up
Examples of connection with a VCR/DVD player
*
In the default setting, the AUDIO IN2 L/R port is the audio port for the VIDEO, S-VIDEO
and COMPONENT VIDEO ports. To change the settings, refer to the AUDIO item in the
SETUP menu. ( 34)
Audio/Video cable
AUDIO IN2
R
Y
CONTROL
RGB IN1
Audio (R) out
RGB IN2
RGB OUT
USB
AUDIO OUT
CB/PB
L
K
AUDIO IN1
Audio (L) out
Video out
VIDEO
S-VIDEO
Audio cable
AUDIO IN2
R
Y
CONTROL
RGB IN1
Audio (R) out
RGB IN2
RGB OUT
USB
AUDIO OUT
CB/PB
CR/PR
L
K
AUDIO IN1
Audio (L) out
S-Video out
VIDEO
S
S-Video cable
Component video out
Y
Component video cable
AUDIO IN2
Y
R
CONTROL
RGB IN1
CB/PB
CR/PR
RGB IN2
RGB OUT
USB
O OUT
CB/PB
CR/PR
L
K
AUDIO IN1
VIDEO
S-VIDEO
Audio (R) out
Audio (L) out
Audio cable
8755D-RJ Only!
AUDIO IN2
R
Y
CONTROL
RGB IN1
RGB IN2
RGB OUT
USB
AUDIO OUT
C
C
B
R
/
/
P
B
L
K
AUDIO IN1
PR
LINK
ACT
VIDEO
S-VIDEO
LAN
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up
Connecting power supply
WARNING ►Please use extra caution when connecting the power cord, as
incorrect or faulty connections may result in fire and/or electrical shock.
• Only use the power cord that came with the projector. If it is damaged, contact
your dealer to newly get correct one.
• Only plug the power cord into an outlet rated for use with the power cord's
specified voltage range.
• Never modify the power cord. Never attempt to defeat the ground connection
of the three-pronged plug.
AC inlet
Connector
of the power cord
1. Connect the connector of the power cord to the AC inlet of the projector.
2. Firmly plug the power cord's plug into the outlet.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control
Remote control
Putting batteries
WARNING ►Always handle the batteries with care and use them only as
directed. Improper use may result in battery explosion, cracking or leakage,
which could result in fire, injury and/or pollution of the surrounding environment.
• Be sure to use only the batteries specified. Do not use batteries of different
types at the same time. Do not mix a new battery with used one.
•
Make sure the plus and minus terminals are correctly aligned when loading a battery.
• Keep a battery away from children and pets.
• Do not recharge, short circuit, solder or disassemble a battery.
•
•
Do not allow a battery in a fire or water. Keep batteries in a dark, cool and dry place.
If you observe a leakage of a battery, wipe out the flower and then replace a battery.
If the liquid adheres to your body or clothes, rinse well with water immediately.
Remove the battery cover.
Slide back and remove the battery cover in the direction of the arrow.
1.
Insert the batteries.
Align and insert the two AA batteries according to their plus and minus
terminals as indicated in the remote control.
2.
Close the battery cover.
Replace the battery cover in the direction of the arrow and snap it back into place.
3.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control
Using the remote control
CAUTION ►Be careful in handling the remote control.
• Do not drop or expose the remote control to physical impact.
• Do not get the remote control wet or place it on wet objects. It may result in
malfunction.
• Remove the batteries from the remote control and store them in a safe place if
you won’t be using the remote control for an extended period.
• Replace the batteries whenever the remote control starts malfunctioning.
• When strong lights (such as direct sunlight) or light from an extremely close
range (such as from an inverter fluorescent lamp), hit the projector’s remote
sensor, the remote control may cause to function. Adjust the direction of the
projector to keep the light from directly hitting the projector’s remote sensor.
The remote control works with the projector’s remote sensor.
approx. 3 meters
30º
30º
• The range of the remote sensor is 3 meters with a 60 degree range (30 degrees
to the left and right of the remote sensor).
• Also a remote signal reflected in the screen etc. may be available. If it is difficult
to send a remote signal to the sensor directly, please try to use the reflected signal.
• Since the remote control uses infrared light to send signals to the projector
(Class1 LED), be sure to use the remote control in an area free from obstacles
that could block the remote control’s output signal to the projector.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Power on/off
Power on/off
WARNING ►When the power is on, a strong light is emitted. Do not look into
the lens of projector. Also do not peep at the inside of projector through a hole.
NOTE • Turn the power on/off in right order. Please power on the projector prior
to the connected devices. Power off the projector later than the connected devices.
Turning on the power
POWER
indicator
STANDBY/ON
button
Make sure that the power cord is firmly and
correctly connected to the projector and the
1.
VIDEO
RGB
SEARCH
ASPECT
AUTO
BLANK
outlet.
MAGNIFY
HOME
PAGE UP
VOLUME
MUTE
ON
END
PAGE DOWN
OFF
Remove the lens cover, and set the power
switch to the ON position.
The power indicator will light up in steady orange.
Then wait several seconds because the buttons
may not function for these several seconds.
FREEZE
KEYSTONE
2.
POSITION
MENU
ENTER
ESC
RESET
Press the STANDBY/ON button on the projector or the remote control.
The projector lamp will light up and the POWER
3.
POWER
indicator will begin blinking in green. When the power is
completely on, the indicator will stop blinking and light in
green.
(Steady orange)
POWER
(Blinking in green)
To display the picture, select an input signal according to
POWER
(
18)
.
the section "Selecting an input signal"
(Steady green)
Turning off the power
This product is able to turn off the main power during the cooling. However, please
pay special attention to below two points when you do:
(1) Please do not turn the projector on again for at least 1 minute in this case.
Neglect could shorten the lifetime of the lamp.
(2) During use or immediately after use, do not touch around the lamp and vents
(
4
)
of the projector
It could cause a burn.
Press the STANDBY/ON button on the projector or the remote control.
The message "Power off?" will appear on the screen for approximately 5
seconds.
1.
Press the STANDBY/ON button on the projector or the
Power off?
2.
remote control again while the message appears.
The projector lamp will go off, and the POWER indicator will
begin blinking in orange.
POWER
Then the POWER indicator will stop blinking and light in
steady orange when the lamp cooling is complete.
(Blinking in orange)
POWER
Make sure that the power indicator lights in steady orange,
and set the power switch to the OFF position. The POWER
indicator will go off. Attach the lens cover.
3.
(Steady orange)
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating
Operating
Adjusting the volume
Press the VOLUME button on the remote control.
A dialog will appear on the screen to aid you in adjusting the volume.
1.
SEARCH
AUTO
VIDEO
RGB
BLANK
ASPECT
2. Use the cursor buttons ▲/▼ to adjust the volume.
MAGNIFY
HOME
PAGE UP
VOLUME
MUTE
ON
To close the dialog and complete the operation, press the
PAGE DOWN
VOLUME button again. Even if you don’t do anything, the
dialog will automatically disappear after a few seconds.
BLANK
ASPECT
MAGNIFY
AUTO
Temporarily muting the sound
HOME
END
PAGE UP
VOLUME
MUTE
ON
Press the MUTE button on the remote control.
A dialog will appear on the screen indicating that you have muted the sound.
1.
PAGE DOWN
OFF
To restore the sound, press the MUTE or VOLUME button.
FREEZE
KEYSTONE
Even if you don’t do anything, the dialog will automatically
disappear after a few seconds.
Selecting an input signal
Press the INPUT button on the projector.
Each time you press the button, the projector switches its
input port as below.
1.
RGB IN1
RGB IN2
VIDEO
S-VIDEO
COMPONENT VIDEO
● When the RGB IN2/RGB OUT port functions as an RGB out
port (the RGB IN OUT switch is pushed in), RGB IN2 cannot
be selected. In that case “RGB2/RGB OUT RGB OUT” message will be
displayed.
Press the RGB button on the remote control to select an
input port for the RGB signal.
Each time you press the button, the projector switches its RGB
input port as below.
1.
SEARCH
AUTO
VIDEO
RGB
BLANK
ASPECT
RGB IN1
RGB IN2
● If the RGB button is pushed (when switching from VIDEO to RGB signals)
when TURN ON is selected for the AUTO SEARCH item in the OPTION menu
the projector will check the RGB IN1 port first. If no input is detected at the port,
the projector will check the RGB IN2 port.
● When the RGB IN2/RGB OUT port functions as an RGB out port (the RGB IN
OUT switch is pushed in), RGB IN2 cannot be selected. In that case “RGB2/
RGB OUT RGB OUT” message will be displayed.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating
Selecting an input signal (continued)
Press the VIDEO button on the remote control to select an
input for video signal.
Each time you press the button, the projector switches its
video input port as below.
1.
SEARCH
AUTO
VIDEO
RGB
BLANK
ASPECT
COMPONENT VIDEO
S-VIDEO
VIDEO
● If the VIDEO button is pushed (when switching from RGB to VIDEO signals)
when TURN ON is selected for the AUTO SEARCH item in the OPTION menu
the projector will check the COMPONENT VIDEO port first. If no input is
detected at the port, projector will begin to check other ports in above order.
Searching an input signal
SEARCH
AU
1. Press the SEARCH button on the remote control.
VIDEO
RGB
BLANK
ASPECT
The projector will start to check its input ports in order to
find any input signals.
Then when an input is found, the projector will stop searching and display the
image. If no signal is found, the projector will return to the state selected before
the operation.
RGB IN 1
RGB IN 2
COMPONENT VIDEO
S-VIDEO
VIDEO
Selecting an aspect ratio
Press the ASPECT button on the remote control.
Each time you press the button, the projector switches the mode for aspect
ratio in turn.
1.
For an RGB signal
NORMAL 4:3
16:9
SEARCH
AUTO
VIDEO
RGB
BLANK
VOLUME
ASPECT
For a video signal/no signal
4:3 16:9 SMALL
MAGNIFY
HOME
PAGE UP
ON
● The NORMAL mode keeps the original aspect ratio of the signal.
● For an HDTV signal of 1125i (1080i) or 750p (720p) as the COMPONENT
VIDEO input, only 16:9 mode can be selected.
● Performing the automatic adjustment initializes the aspect ratio setting.
Zoom knob
Adjusting the zoom and focus
1. Use the zoom knob to adjust the screen size.
Focus ring
2. Use the focus ring to focus the picture.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating
Using the automatic adjustment feature
1. Press the AUTO button on the remote control.
SEARCH
AUTO
VIDEO
RGB
For an RGB signal
BLANK
VOLUME
ASPECT
The vertical position, the horizontal position, the clock phase
and the horizontal size will be automatically adjusted.
MAGNIFY
HOME
PAG
ON
And the aspect ratio will be automatically selected. Make sure that the
application window is set to its maximum size prior to attempting to use this
feature. A dark picture may still be incorrectly adjusted. Use a bright picture
when adjusting.
For a video signal or s-video signal
The video format best suited for the respective input signal will be selected
automatically.
This function is available only when the AUTO mode is selected to the
(
32)
VIDEO FORMAT item in the INPUT menu
. For a component video
signal, the signal type is identified automatically independently of this
function.
For a video signal, s-video signal or component video signal
The vertical position and horizontal position will be automatically adjusted.
For a component video signal
The aspect ratio will be automatically selected.
The clock phase will be automatically adjusted.
● The automatic adjustment operation requires approximately 10 seconds. Also
please note that it may not function correctly with some input.
PAGE DOWN
MUTE
END
OFF
Adjusting the position
FREEZE
KEYSTONE
Press the POSITION button on the remote control.
1.
The “POSITION” indication will appear on the screen.
MENU
POSITION
Use the cursor buttons ▲/▼/◄/► to adjust the picture
2.
position.
When you want to reset the operation, press the RESET button on the remote
control during the operation.
To complete this operation, press the POSITION button again. Even if you don’t
do anything, the dialog will automatically disappear after a few seconds.
● When this function is performed at a video signal, a certain extra such as a line
may appear outside a picture.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating
Correcting the keystone distortions
MAGNIFY
HOME
END
PAGE UP
VOLUME
MUTE
Press the KEYSTONE button on the remote control. A
1.
ON
dialog will appear on the screen to aid you in correcting the
distortion.
PAGE DOWN
OFF
FREEZE
KEYSTONE
Use the cursor buttons ▲/▼ to correct the distortion.
To close the dialog and complete this operation, press the
KEYSTONE button again. Even if you don’t do anything, the
dialog will automatically disappear after a few seconds.
2.
● The adjustable range for correction will vary among inputs. For some input, this
function may not work well.
● When V:INVERT or H&V:INVERT is selected to the MIRROR item in the
SETUP menu, if the projector screen is inclined or angled downward, this
function may not work correctly.
● When the zoom adjustment is set to the TELE (telephoto focus), this correction
may be excessive. This function should be used when the zoom adjustment is
set to the WIDE (wide-angle focus) whenever possible.
Using the magnify feature
SEARCH
AUTO
VIDEO
RGB
Press the ON button of MAGNIFY on the remote control.
The “MAGNIFY” indication will appear on the screen
1.
BLANK
VOLUME
ASPECT
MAGNIFY
(although the indication will disappear in several seconds with
no operation), and the projector will enter the MAGNIFY mode.
HOME
PAGE UP
ON
2. Use the cursor buttons ▲/▼ to adjust the zoom level.
To move the zoom area, press the POSITION button in the MAGNIFY mode,
then use the cursor buttons ▲/▼/◄/► to move the area. And to finalize the
zoom area, press the POSITION button again.
To exit the MAGNIFY mode and restore the screen to normal, press the OFF
button of MAGNIFY on the remote control.
● The projector automatically exits the MAGNIFY mode when the input signal is
changed, or when the display condition is changed.
● Although in the MAGNIFY mode, the keystone distortion condition may vary, it
will be restored when the projector exits the MAGNIFY mode.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating
Freezing the screen
MAGNIFY
HOME
END
PAGE UP
VOLUME
MUTE
Press the FREEZE button on the remote control.
1.
ON
The “FREEZE” indication will appear on the screen, and the
projector will enter the FREEZE mode.
PAGE DOWN
OFF
FREEZE
KEYSTONE
To exit the FREEZE mode and restore the screen to normal,
press the FREEZE button again.
● The projector automatically exits the FREEZE mode when the input signal
changes, or when one of the projector’s buttons or the remote control buttons
of STANDBY/ON, SEARCH, RGB, VIDEO, BLANK, AUTO, ASPECT, VOLUME,
MUTE, KEYSTONE, POSITION and MENU is pressed.
● If the projector continues projecting a still image for long time, the LCD panel
might possibly be printed. Do not leave the projector in the FREEZE mode for
too long.
Temporarily blanking the screen
Press the BLANK button on the remote control.
The blank screen will be displayed instead of the screen of
input signal. Please refer to the BLANK item in the SCREEN
1.
SEARCH
AUTO
VIDEO
RGB
BLANK
VOLUME
ASPECT
MAGNIFY
(
35).
menu
HOME
PAGE UP
To exit the blank screen and return to the input signal screen, press the
BLANK button again.
● The projector automatically returns to the input signal screen when the input
signal is changed, or when one of the projector’s buttons or the remote control
buttons is pressed.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating
Operating the computer screen
CAUTION ►Mistaken use of the mouse/keyboard control could damage
your equipment.
• While using this function, please connect only with a computer.
• Before connecting, read the manuals of the computer you will connect.
NOTE • It may not be possible to control notebook PC, and other computers with
built-in pointing device (e.g. track ball), using this remote control. In this case, before
connecting go into BIOS (system setup) and select external mouse, and disable the
pointing device. In addition, the mouse may not function if the computer does not have
the needed utility program. See your computer’s hardware manual for details.
• The USB control can be used with Windows 95 OSR 2.1 or higher. It may not be
possible to use the remote control, depending on the computer’s configurations and
mouse drivers.
• The USB control can be used only for the functions listed below. You cannot do things
like press two buttons at once (for instance, pressing two buttons at the same time to
move the mouse pointer diagonally).
• This function is not available while the lamp is warming up (the POWER indicator
flashes green), and while adjusting the volume and display, correcting for trapezoidal
distortion, zooming in on the screen, using the BLANK function, or displaying the menu
screen.
USB mouse and keyboard control
1. Connect the projector’s USB port to the computer via the mouse cable.
SEARCH
VIDEO
RGB
Available function
Remote control operation
BLANK
ASPECT
AUTO
Move pointer
Left click with mouse
Right click with mouse
Use ▲, ▼, ◄, ► buttons
Press ENTER button
Press RESET button
Press HOME button
Press END button
Press PAGE UP button
Press PAGE DOWN button
Press ESC button
MAGNIFY
HOME
END
PAGE UP
VOLUME
MUTE
ON
PAGE DOWN
OFF
FREEZE
KEYSTONE
Press keyboard’s HOME key
Press keyboard’s END key
Press keyboard’s PAGE UP key
Press keyboard’s PAGE DOWN key
Press keyboard’s ESC key
POSITION
MENU
ENTER
ESC
RESET
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Multifunctional settings
Multifunctional settings
Using the menu function
This projector has the following menus: PICTURE, IMAGE, INPUT, SETUP, SCREEN,
OPTION, and EASY MENU. EASY MENU cosists of functions often used, and the
other menus are classified into each purpose. Each of these menus is operated using
the same methods. The basic operations of these menus are as follows.
VIDEO
RGB
SEARCH
MENU button
ASPECT
AUTO
BLANK
POSITION
MENU
MAGNIFY
HOME
END
PAGE UP
VOLUME
MUTE
ON
PAGE DOWN
OFF
ENTER button
Cursor buttons
FREEZE
KEYSTONE
ENTER
POSITION
MENU
ESC
RESET
ENTER
ESC
RESET
RESET button
ꢀMENUꢀ[RGB]
ꢀꢀꢀ:SELECT
Press the MENU button on the remote control or one of
the cursor buttons on the projector.
1.
ꢀPICTURE
ꢀIMAGE
ꢀINPUT
ꢀBRIGHTNESSꢀꢀꢀꢀꢀ＋0
ꢀCONTRASTꢀꢀꢀꢀꢀꢀꢀ＋0
ꢀGAMMAꢀꢀꢀꢀꢀꢀꢀꢀDEFAULTꢀ1
ꢀCOLORꢀTEMPꢀꢀꢀMIDDLE
ꢀCOLORꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ+0
ꢀTINTꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ+0
ꢀSHARPNESSꢀꢀꢀꢀꢀꢀꢀꢀ3
ꢀPROGRESSIVEꢀꢀTURNꢀOFF
ꢀMYꢀMEMORYꢀꢀꢀꢀSAVEꢀ1
ꢀSETUP
The Advanced MENU or EASY MENU will appear.
ꢀSCREEN
ꢀOPTION
ꢀEASYꢀMENU
In the EASY MENU
If you want to change it to the Advanced MENU, select the
"Go to Advanced Menu"
2.
ꢀEASYꢀMENU
ꢀASPECTꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ4:3
KEYSTONE
MODE
BRIGHTNESS
CONTRAST
COLOR
3. Use the cursor buttons ▲/▼ to select an item to operate.
+0
NORMAL
+0
+0
+0
+0
ꢀ3
4. Use the cursor buttons◄/► to operate the item.
TINT
In the Advanced MENU
SHARPNESS
WHISPER
MIRROR
RESET
FILTERꢀTIME
LANGUAGE
NORMAL
NORMAL
Use the cursor buttons ▲/▼ to select a menu.
2.
If you want to change it to the EASY MENU, select the
ꢀꢀꢀ0h
ENGLISH
EASY MENU.
ꢀGoꢀToꢀAdvanceꢀMenu...
Then press the cursor button ► on the projector or remote
control, or the ENTER button on the remote control to select
an item. The display of the selected menu will be active.
Use the cursor buttons ▲/▼ to select an item to operate.
3.
Then press the cursor button
►
on the projector or remote control, or the ENTER button
on the remote control to progress. The operation menu of the selected item will appear.
4. Use the cursor buttons▲/▼ to operate the item.
●
When you want to reset the operation, press the RESET button on the remote control
during the operation. Note that items whose functions are performed simultaneously
with operation (ex. LANGUAGE, H PHASE, VOLUME etc.) cannot be reset.
●
In the advanced menu, when you want to return to the previous display, press the cursor
button
◄
on the projector or remote control, or the ESC button on the remote control.
Press the MENU button on the remote control again to close the menu
and complete this operation. Even if you don't do anything, the dialog will
5.
automatically disappear after about 10 seconds.
● Some functions cannot be performed when a certain input port is selected, or
when a certain input signal is displayed.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Multifunctional settings
ꢀEASYꢀMENU
EASY Menu
ꢀASPECTꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ4:3
KEYSTONE
+0
With the EASY MENU, items shown in the table below can
be performed.
MODE
NORMAL
+0
+0
+0
+0
ꢀ3
BRIGHTNESS
CONTRAST
COLOR
Select an item using the cursor buttons ▲/▼ on the
projector or remote control. Then perform it referring to the
following table.
TINT
SHARPNESS
WHISPER
MIRROR
NORMAL
NORMAL
RESET
FILTERꢀTIME
LANGUAGE
ꢀꢀꢀ0h
ENGLISH
ꢀGoꢀToꢀAdvanceꢀMenu...
Item
Description
Using the buttons ◄/► switches the mode for aspect ratio.
ASPECT
See the ASPECT item in the IMAGE menu ( 30).
Using the buttons ◄/► corrects the keystone distortion.
KEYSTONE
See the item KEYSTONE of section SETUP menu. ( 21)
Using the buttons ◄/► switches the mode of picture type. The
modes of picture type are combinations of a mode of GAMMA and
a mode of COLOR TEMP. Choose a suitable mode according to the
projected source.
NORMAL
CINEMA
DYNAMIC
NORMAL: (COLOR TEMP = MIDDLE) + (GAMMA = #1 DEFAULT)
CINEMA: (COLOR TEMP = LOW) + (GAMMA = #2 DEFAULT)
DYNAMIC: (COLOR TEMP = HIGH) + (GAMMA = #3 DEFAULT)
MODE
• When the combination of GAMMA and COLOR TEMP differs from
pre-assigned modes above, the display on the menu for the MODE
is “CUSTOM”. Please refer to the GAMMA ( 27) and COLOR
TEMP ( 28) items in the PICTURE menu.
•
When this function is performed, a certain extra such as a line may appear.
Using the buttons ◄/► adjusts the brightness.
See the item BRIGHTNESS in the PICTURE menu ( 27).
BRIGHTNESS
CONTRAST
COLOR
Using the buttons ◄/► adjusts the contrast.
See the item CONTRAST of section PICTURE menu
(
27).
Using the buttons ◄/► adjusts the strength of whole color.
See the COLOR item in the PICTURE menu ( 28).
Using the buttons ◄/► adjusts the tint.
See the TINT item in the PICTURE menu ( 28).
TINT
Using the buttons ◄/► adjusts the sharpness.
See the SHARPNESS item in the PICTURE menu
• There may be some noise when an adjustment is made. This is
not a malfunction.
(
28).
SHRPNESS
WHISPER
Using the buttons ◄/► turns off/on the whisper mode.
See the WHISPER item in the SETUP menu ( 34).
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Multifunctional settings
EASY Menu (continued)
Item
Description
Using the buttons ◄/► switches the mode for mirror status.
MIRROR
See the MIRROR item in the SETUP menu ( 34).
Performing this item resets all of the items of EASY MENU except
FILTER TIME and LANGUAGE.
A dialog is displayed for confirmation. Selecting RESET using the
button ▲ performs resetting.
RESET
Performing this item resets the filter timer which counts usage time
of the air filter.
A dialog is displayed for confirmation. Selecting RESET using the
button ▲ performs resetting.
FILTER TIME
See the FILTER TIME item in the OPTION menu ( 38).
Select the LANGUAGE item to toggle the menu language. Refer to
LANGUAGE
Go To
description of LANGUAGE in the SCREEN menu ( 35).
Select “Go To Advanced Menu” to use the menu of PICTURE,
Advanced Menu IMAGE, INPUT, SETUP, SCREEN or OPTION.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Multifunctional settings
PICTURE Menu
ꢀMENUꢀ[RGB]
ꢀꢀꢀ:SELECT
ꢀBRIGHTNESSꢀꢀꢀꢀꢀ＋0
With the PICTURE menu, the items shown in the table
below can be performed.
ꢀPICTURE
ꢀIMAGE
ꢀINPUT
ꢀCONTRASTꢀꢀꢀꢀꢀꢀꢀ＋0
ꢀGAMMAꢀꢀꢀꢀꢀꢀꢀꢀDEFAULTꢀ1
ꢀCOLORꢀTEMPꢀꢀꢀMIDDLE
ꢀCOLORꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ+0
ꢀTINTꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ+0
ꢀSHARPNESSꢀꢀꢀꢀꢀꢀꢀꢀ3
ꢀPROGRESSIVEꢀꢀTURNꢀOFF
ꢀMYꢀMEMORYꢀꢀꢀꢀSAVEꢀ1
Select an item using the cursor buttons ▲/▼ on the
projector or remote control, and press the cursor button ►
on the projector or remote control, or the ENTER button
on the remote control to execute the item. Then perform it
referring to the following table.
ꢀSETUP
ꢀSCREEN
ꢀOPTION
ꢀEASYꢀMENU
Item
Description
BRIGHTNESS
CONTRAST
Using the buttons ▲/▼ adjusts the brightness. : Light
Using the buttons ▲/▼ adjusts the contrast. : Strong
Using the buttons ▲/▼ switches the GAMMA mode.
Dark
Weak
#1 DEFAULT
#1 CUSTOM
#2 DEFAULT
#3 CUSTOM
#3 DEFAULT
#2 CUSTOM
To adjust #1 CUSTOM, #2 CUSTOM or #3 CUSTOM
Selecting a mode of CUSTOM and then
pressing the button ► or the ENTER button
displays a dialog to aid you in adjusting the
mode.
ENTER :
1
2
3
4
5
6
7
8
This function is useful when you want to
change the brightness of particular tones.
+0 +0 +0 +0 +0 +0 +0 +0
Choose an item using the buttons ◄/►, and
adjust the level using the buttons ▲/▼.
[
]
GAMMA CUSTOM 1
GAMMA
You can display a test pattern for checking the effect of your
adjustment by pressing the ENTER button.
Each time you press the ENTER button, the pattern changes as
below.
No pattern Gray scale of 9 steps
Ramp Gray scale of 15 steps
The eight equalizing bars correspond to eight tone levels of the
test pattern except the darkest in the left end. If you want to adjust
the 2nd tone from left end on the test pattern, use the equalizing
adjustment bar “1”. The darkest tone at the left end of the test
pattern cannot be controlled with any of equalizing adjustment bar.
• When this function is performed, a certain extra such as a line
may appear.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Multifunctional settings
PICTURE Menu (continued)
Item
Description
Using the buttons ▲/▼ switches the mode of color temperature.
HIGH MIDDLE LOW CUSTOM
To adjust CUSTOM
Selecting the CUSTOM and then pressing the
button ► or the ENTER button displays a dialog
to aid you in adjusting the OFFSET and/or GAIN
of the CUSTOM mode.
ENTER
:
OFFSET
G
GAIN
G
R
B
R
B
OFFSET adjustments change the color intensity
on the whole tones of the test pattern.
+0 +0 +0
+0 +0 +0
COLOR TEMP
GAIN adjustments mainly affect color intensity
on the brighter tones of the test pattern.
COLOR TEMP
Choose an item using the buttons ◄/►, and adjust the level using
the buttons ▲/▼.
You can display a test pattern for checking the effect of your
adjustment by pressing the ENTER button.
Each time you press the ENTER button, the pattern changes as
below.
No pattern Gray scale of 9 steps
Ramp Gray scale of 15 steps
• When this function is performed, a certain extra such as a line
may appear.
Using the buttons ▲/▼ adjusts the strength of whole color.
COLOR
TINT
Strong
Weak
• This item can be selected only for a video signal.
Using the buttons ▲/▼ adjusts the tint.
Green
Red
• This item can be selected only for a video signal except for
SECAM.
Using the buttons ▲/▼ adjusts the sharpness.
Strong
Weak
SHARPNESS
• There may be some noise and/or the screen may flicker for a
moment when an adjustment is made. This is not a malfunction.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Multifunctional settings
PICTURE Menu (continued)
Item
Description
Using the buttons ▲/▼ switches the progress mode.
TV FILM TURN OFF
• This function is performed only for an interlaced signal of a VIDEO
input, an S-VIDEO input or CONPONENT VODEO input of 525i
(480i) or 625i (576i) signal.
PROGRESSIVE
• When TV or FILM is selected, the screen image will be sharp.
FILM adapts to the 2-3 Pull-Down conversion system. But these
may cause a certain defect (for example, jagged line) of the picture
for a quick moving object. In such a case, please select TURN OFF,
even though the screen image may lose the sharpness.
Selecting a mode of MY MEMORY using the buttons ▲/▼ and then
pressing the button ► or the ENTER button performs each function.
LOAD1
LOAD2
LOAD3
LOAD4
SAVE4 SAVE3
SAVE2
SAVE1
This projector has 4 numbered memories for adjustment data.
Performing the LOAD1, LOAD2, LOAD3 or LOAD4 loads the data on
the memory whose number corresponds to the command’s number,
and adjusts the picture automatically depending on the data.
Performing the SAVE1, SAVE2, SAVE3 or SAVE4 saves the current
adjustment data on the memory whose number corresponds to the
command’s number.
MY MEMORY
• The current adjustment data of the items in the PICTURE menu is
stored, except for the adjustment data in the CUSTOM modes for
the GAMMA and COLOR TEMP items.
• There may be some noise and/or the screen may flicker for a
moment when data is loaded to memory. This is not a malfunction.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Multifunctional settings
IMAGE Menu
ꢀMENUꢀ[RGB]
ꢀꢀꢀ:SELECT
ꢀASPECTꢀꢀꢀꢀꢀꢀꢀꢀꢀ4:3
With the IMAGE menu, items shown in the table below can
be performed.
ꢀPICTURE
ꢀIMAGE
ꢀOVERꢀSCANꢀꢀꢀꢀꢀꢀ5
ꢀVꢀPOSITIONꢀꢀꢀꢀꢀ25
ꢀHꢀPOSITIONꢀꢀꢀꢀꢀ142
ꢀHꢀPHASEꢀꢀꢀꢀꢀꢀꢀꢀ16
ꢀHꢀSIZEꢀꢀꢀꢀꢀꢀꢀꢀꢀ1344
ꢀAUTOꢀADJUSTꢀEXECUTE
ꢀINPUT
ꢀSETUP
Select an item using the cursor buttons ▲/▼ on the
projector or remote control, and press the cursor button ►
on the projector or remote control, or the ENTER button
on the remote control to execute the item. Then perform it
referring to the following table.
ꢀSCREEN
ꢀOPTION
ꢀEASYꢀMENU
Item
Description
Using the buttons ▲/▼ switches the mode for aspect ratio.
For an RGB signal
4:3
16:9 NORMAL
For a video signal / no signal
4:3 16:9 SMALL
ASPECT
• The NORMAL mode keeps the original aspect ratio of the signal.
• For an HDTV signal of 1125i (1080i) or 750p (720p) as the
COMPONENT VIDEO input, this item can't be selected.
Using the buttons ▲/▼ adjusts the over-scan ratio.
Large (It reduces picture)
Small (It magnifies picture)
OVER SCAN
V POSITION
• This item can be selected only for a video signal.
• When this adjustment is too large, certain degradation may appear
at the frame area of the picture. In such a case, please adjust small.
Using the buttons ▲/▼ adjusts the vertical position.
Up
Down
• Over-adjusting the vertical position may cause noise to appear
on the screen. If this occurs please reset the vertical position to the
default setting. Pressing the RESET button when V POSITION is
selected will reset the V POSITION to the default setting.
Using the buttons ▲/▼ adjusts the horizontal position.
Left
Right
• Over-adjusting the horizontal position may cause noise to appear
on the screen. If this occurs please reset the horizontal position to
the default setting. Pressing the RESET button when H POSITION
is selected will reset the H POSITION to the default setting.
H POSITION
H PHASE
Using the buttons ▲/▼ adjusts the horizontal phase to eliminate
flicker.
Right
Left
• This item can be selected only for an RGB signal or a component
video signal. Note that this does not work with the input signal of
525i(480i)/625i(576i)/SCART RGB from the component video port.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Multifunctional settings
IMAGE Menu (continued)
Item
Description
Using the buttons ▲/▼ adjusts the horizontal size.
Large Small
• This item can be selected only for an RGB signal.
H SIZE
• When this adjustment is excessive, the picture may not be
displayed correctly. In such a case, please reset the adjustment
by pressing the RESET button on the remote control during this
operation.
Selecting this item performs the automatic adjustment feature.
For an RGB signal
The vertical position, the horizontal position, the clock phase and
the horizontal size will be automatically adjusted. And the aspect
ratio will be automatically selected.
Make sure that the application window is set to its maximum size
prior to attempting to use this feature. A dark picture may still be
incorrectly adjusted. Use a bright picture when adjusting.
For a video signal or s-video signal
The video format best suited for the respective input signal will be
selected automatically.
This function is available only when the AUTO mode is selected to
the VIDEO FORMAT item in the INPUT menu. For a component
video signal, the signal type is identified automatically independently
of this function.
AUTO ADJUST
EXECUTE
For a video signal, s-video signal or component video signal
The vertical position and horizontal position will be automatically
adjusted.
For a component video signal
The aspect ratio will be automatically selected.
The clock phase will be automatically adjusted.
• The automatic adjustment operation requires approximately 10
seconds. Also please note that it may not function correctly with
some input.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Multifunctional settings
INPUT Menu
ꢀMENUꢀ[RGB]
ꢀꢀꢀ:SELECT
ꢀCOLORꢀSPACEꢀꢀAUTO
ꢀCOMPONENTꢀꢀꢀꢀCOMPONENT
ꢀVIDEOꢀFORMATꢀAUTO
With the INPUT menu, the items shown in the table below
can be performed.
ꢀPICTURE
ꢀIMAGE
ꢀINPUT
ꢀFRAMEꢀLOCK
ꢀINFORMATION
TURNꢀON
ꢀSETUP
Select an item using the cursor buttons ▲/▼ on the
projector or remote control, and press the cursor button ►
on the projector or remote control, or the ENTER button
on the remote control to execute the item. Then perform it
referring to the following table.
ꢀSCREEN
ꢀOPTION
ꢀEASYꢀMENU
Item
Description
Using the buttons ▲/▼ switches the mode for color space.
AUTO RGB SMPTE240 REC709 REC601
• This item can be selected only for an RGB signal or a component
video signal (except signals of 525i(480i)/625i(576i)/SCART RGB
from the component video port).
COLOR SPACE
• The AUTO mode automatically selects the optimum mode.
• The AUTO operation may not work well at some signals. In such a
case, it might be good to select a suitable mode except AUTO.
Using the buttons ▲/▼ switches the function of COMPONENT
VIDEO port.
COMPONENT
SCART RGB
COMPONENT
When the SCART RGB is selected, the COMPONENT VIDEO port
function as a port for a SCART RGB signal input. A SCART adapter
and SCART cable realize a SCART RGB input to the projector. For
details, contact your dealer.
Using the buttons ▲/▼ switches the mode for video format.
AUTO
NTSC
PAL SECAM
N-PAL
M-PAL NTSC4.43
• This item is performed only for a video signal from the VIDEO port
or the S-VIDEO port. For a component video signal, the signal type
is identified automatically independently of this function.
VIDEO FORMAT
• The AUTO mode automatically selects the optimum mode.
• The AUTO operation may not work well for some signals. If the
picture becomes unstable (ex. an irregular picture, a color lack),
please select the mode depending on the input signal.
Using the buttons ▲/▼ turns the frame lock function on/off.
TURN ON
TURN OFF
• This item performs only at a RGB signal with vertical frequency of
50 to 72 Hz for the model TBD, or 50 to 60 Hz for the model
8755D.
FRAME LOCK
• When the TURN ON is selected, a moving picture is displayed
more smoothly.
• This function may cause a certain degradation of the picture. In
such a case, please select the TURN OFF.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Multifunctional settings
INPUT Menu (continued)
Item
Description
Selecting this item displays a dialog titled “INPUT INFORMATION”.
It shows the information about the current input.
INPUT-INFORMATION
RGB
1024x768 @60.0
FRAME LOCK
INPUT-INFORMATION
S-VIDEO
INPUT-INFORMATION
COMPONENT
576i @50
SECAM
AUTO
SCART RGB
• The “FRAME LOCK” message on the dialog means the frame lock
function is working. This function automatically works when a RGB
signal with vertical frequency of 50 to 60 Hz is input, and it displays
a moving picture more smoothly.
INFORMATION
• The “SCART RGB” message means the COMPONENT VIDEO
port is working as a SCART RGB input port. Please refer to the
COMPONENT item in this menu. ( 32)
• This item can't be selected for no signal and sync out.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Multifunctional settings
SETUP Menu
ꢀMENUꢀ[RGB]
ꢀꢀꢀ:SELECT
ꢀKEYSTONEꢀꢀꢀꢀꢀ+0
With the SETUP menu, the items shown in the table below
can be performed.
Select an item using the cursor buttons ▲/▼ on the
projector or remote control, and press the cursor button ►
on the projector or remote control, or the ENTER button
on the remote control to execute the item. Then perform it
referring to the following table.
ꢀPICTURE
ꢀIMAGE
ꢀINPUT
ꢀWHISPERꢀꢀꢀꢀꢀꢀNORMAL
ꢀMIRRORꢀꢀꢀꢀꢀꢀꢀNORMAL
ꢀVOLUMEꢀꢀꢀꢀꢀꢀꢀ16
ꢀAUDIOꢀ
ꢀSETUP
ꢀSCREEN
ꢀOPTION
ꢀEASYꢀMENU
Item
Description
Using the buttons ▲/▼ corrects the keystone distortion.
Upper in the data Lower in the data
• The adjustable range of this function will vary with the type of input
signal. At some signals, this function may not work well.
• When the V:INVERT or the H&V:INVERT is selected under the
item MIRROR, if the projector screen is inclined or if the projector is
angled downward, this function may not work correctly.
KEYSTONE
• When the zoom adjustment is set to the TELE side, this correction
may be excessive. This function should be used with zoom set to
WIDE whenever possible.
Using the buttons ▲/▼ turns off/on the whisper mode.
NORMAL
WHISPER
WHISPER
• When the WHISPER is selected, acoustic noise and screen
brightness are reduced.
Using the buttons ▲/▼ switches the mode for mirror status.
MIRROR
VOLUME
NORMAL
H:INVERT
V:INVERT H&V:INVERT
Using the buttons ▲/▼ adjusts the volume.
High Low
ꢀAUDIO
Choose an input port using the buttons ▲/▼
(1), then select the audio port to be interlocked
with the input port using the buttons ◄/► (2).
When off is selected, both of two audio ports
do not work for the input port.
ꢀꢀꢀQUIT
ꢀꢀ
ꢀRGB1
1ꢀꢀꢀ2
ꢀRGB2
ꢀCOMPONENT
ꢀS‑VIDEO
ꢀVIDEO
AUDIO
(1) RGB1
RGB2
COMPONENT
S-VIDEO
VIDEO
(2) 1
2
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Multifunctional settings
SCREEN Menu
ꢀMENUꢀ[RGB]
ꢀꢀꢀ:SELECT
With the SCREEN menu, the items shown in the table
below can be performed.
ꢀPICTURE
ꢀIMAGE
ꢀINPUT
ꢀSETUP
ꢀSCREEN
ꢀLANGUAGEꢀꢀꢀꢀꢀꢀENGLISH
ꢀMENUꢀPOSITION
ꢀOSDꢀBRIGHT.ꢀꢀꢀ5
ꢀBLANKꢀꢀꢀꢀꢀꢀꢀꢀꢀBLACK
ꢀSTARTꢀUPꢀꢀꢀꢀꢀꢀORIGINAL
ꢀMyScreen
Select an item using the cursor buttons ▲/▼ on the
projector or remote control, and press the cursor button ►
on the projector or remote control, or the ENTER button
on the remote control to execute the item. Then perform it
referring to the following table.
ꢀOPTION
ꢀEASYꢀMENU
ꢀMyScreenꢀLockꢀTURNꢀOFF
ꢀMESSAGEꢀꢀꢀꢀꢀꢀꢀTURNꢀON
Item
Description
Using the buttons ▲/▼ switches the OSD (On Screen Display)
language.
ENGLISH FRANÇAIS DEUTSCH ESPAÑOL ITALIANO
NORSK NEDERLANDS PORTUGUÊS 日本語
LANGUAGE
SVENSKA
SUOMI POLSKI TÜRKÇE
Using the buttons ◄/►/▲/▼ adjusts the menu position.
MENU POSITION To quit the operation, press the MENU button on the remote control
or keep no operation for 10 seconds.
Using the buttons ▲/▼ switches the brightness level of the OSD (On
Screen Display).
OSD BRIGHT.
BRIGHT DARK
Using the buttons ▲/▼ switches the mode for the blank screen.
The blank screen is a screen for the temporarily blanking feature
(
22). It is displayed by pressing the BLANK button on the remote
control.
MyScreen
ORIGINAL
BLUE
WHITE
BLACK
BLANK
MyScreen is a screen you can register as a desired screen. The
ORIGINAL screen is the existing standard screen. BLUE, WHITE
and BLACK are non-patterned (plain) screens in each color.
• To avoid remaining as an afterimage, the MyScreen and the
ORIGINAL screens will change to the BLACK screen after several
minutes.
• For the MyScreen, please refer to the MyScreen item ( 36).
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Multifunctional settings
SCREEN Menu (continued)
Item
Description
Using the buttons ▲/▼ switches the mode for the start-up screen.
The start-up screen is a screen displayed when no signal or an
unsuitable signal is detected.
MyScreen
ORIGINAL
TURN OFF
MyScreen is a screen you can register as a desired screen.The
ORIGINAL screen is the existing standard screen. When TURN
OFF is selected, the BLACK screen is used.
START UP
• To avoid remaining as an afterimage, the MyScreen and the
ORIGINAL screens will change to the BLANK screen after several
minutes. If also the BLANK screen is the MyScreen or ORIGINAL, it
will change to the BLACK screen.
• For the MyScreen, please refer to the item MyScreen
. For
below
the BLANK screen, please refer to the BLANK item ( 35).
This item functions for capturing the MyScreen of the blank screen
and the start-up screen. Please execute displaying the input
including the picture you want to capture.
1. Selecting this item displays a dialog titled “MyScreen”. It will ask
you if you start capturing the picture from the current screen.
Please wait for the target picture to be displayed, and press
the ENTER button on the remote control when the picture is
displayed. The picture will freeze and the frame for capturing
appears.
To stop performing, press the RESET or ESC button on the
remote control.
2. Using the buttons ◄/►/▲/▼ adjusts the frame position. Please
move the frame to the position of the picture which you want to
use.
MyScreen
The frame may not be able to be moved for some input signals.
To start registration, press the ENTER button on the remote
control.
To restore the screen and return to the previous dialog, press the
RESET or ESC button on the remote control.
Registration takes several minutes. When the registration is
completed, the registered screen and the message “MyScreen
registration is finished.” are displayed for several seconds. If the
registration failed, the message “A capturing error has occurred.
Please try again.” is displayed.
Using the buttons ▲/▼ turns on/off the MyScreen lock function.
TURN ON
TURN OFF
MyScreen Lock
When the TURN ON is selected, the item MyScreen is locked. Use
this function for protecting the current MyScreen.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Multifunctional settings
SCREEN Menu (continued)
Item
Description
Using the buttons ▲/▼ turns on/off the message function.
TURN ON TURN OFF
When the TURN ON is selected, the following message function
works.
“AUTO IN PROGRESS” while automatically adjusting
”NO INPUT IS DETECTED”
”SYNC IS OUT OF RANGE”
MESSAGE
"Searching….” while searching for the input
”Detecting….” while an input signal is detected
The indication of the input signal displayed by changing
The indication of the aspect ration displayed by changing
The indication of "FREEZE" and "II" while freezing the screen by
pressing the FREEZE button.
• When the TURN OFF is selected, please remember if the picture
is freezing. Do not mistake freezing for a malfurction ( 22).
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Multifunctional settings
OPTION Menu
ꢀMENUꢀ[RGB]
ꢀꢀꢀ:SELECT
With the OPTION menu, the items shown in the table below can
be performed.
Select an item using the cursor buttons ▲/▼ on the projector or
remote control, and press the cursor button ► on the projector
or remote control, or the ENTER button on the remote control to
execute the item, except for the items LAMP TIME and FILTER
TIME. Then perform it referring to the following table.
ꢀPICTURE
ꢀIMAGE
ꢀINPUT
ꢀAUTOꢀSEARCHꢀꢀTURNꢀOFF
ꢀAUTOꢀOFFꢀꢀꢀꢀꢀꢀ0min
ꢀLAMPꢀTIMEꢀꢀꢀꢀꢀ0h
ꢀFILTERꢀTIMEꢀꢀꢀ0h
ꢀSERVICE
ꢀSETUP
ꢀSCREEN
ꢀOPTION
ꢀEASYꢀMENU
ꢀ
Item
Description
Using the buttons ▲/▼ turns on/off the automatic signal search function.
TURN ON TURN OFF
This function works with INPUT, RGB, and VIDEO buttons.
When the TURN ON is selected, detecting no signal automatically
cycles through input ports in the following order. The search is
started from the current port. Then when an input is found, the
projector will stop searching and display the image.
AUTO SEARCH
RGB IN1 RGB IN2 COMPONENT VIDEO S-VIDEO VIDEO
•
When the RGB IN2/RGB OUT port functions as an RGB out port (the
RGB IN OUT switch is pushed in), RGB IN2 cannot be selected. In
that case “RGB2/RGB OUT RGB OUT message will be displayed.
”
Using the buttons ▲/▼ adjusts the time to count down to
automatically turn the projector off.
Long (max. 99 minutes)
Short (min. 0 minute = DISABLE)
AUTO OFF
ENABLE
AUTO OFF
DISABLE
1
0
AUTO OFF
When the time is set to 0, the projector is not turned off automatically.
When the time is set to 1 to 99, and when the passed time with no-
signal or an unsuitable signal reaches at the set time, the projector
lamp will go off and the power indicator begins blinking. Please
refer to the section “Turning off the power” ( 17).
The lamp time is the time counted after the last resetting. It is
shown in the OPTION menu as the usage time of the lamp.
Pressing the RESET button on the remote control or the button ►
of the projector displays a dialog. To reset the lamp time, select the
RESET using the button ▲.
LAMP TIME
RESET CANCEL
• Please reset the lamp time only when you have replaced the lamp,
for a suitable indication about the lamp.
• For the lamp replacement, see the section "Lamp" ( 40, 41).
The filter time is the time counted after the last resetting. It is shown
in the OPTION menu as the usage time of the air filter.
Pressing the RESET button on the remote control or the button ► of the projector
displays a dialog. To reset the filter time, select the RESET using the button ▲.
FILTER TIME
RESET CANCEL
•
Please reset the filter time only when you have cleaned or replaced
the air filter, for a suitable indication about the air filter.
• For the air filter cleaning, see the section "Air filter" ( 42).
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Multifunctional settings
OPTION Menu (continued)
Item
Description
Selecting this item displays the SERVICE menu.
Select an item using the buttons ▲/▼, and press the button ► or
the ENTER button on the remote control to execute the item.
FAN SPEED
AUTO ADJUST
GHOST
KEY LOCK
FILTER MESSAG
FACTORY RESET
FAN SPEED
Using the buttons ▲/▼ switches the rotation speed of the cooling
fans. The HIGH is the mode for use at highlands etc. Note that the
projector is noisier when the HIGH is selected.
HIGH
NORMAL
AUTO ADJUST
Using the buttons ▲/▼ enables/disables the automatic adjustment.
When DISABLE is selected, the automatic adjustment feature is
disabled, although rough adjustment is automatically performed
depending on the basic setting.
ENABLE
DISABLE
•
Depending on conditions, such as input image, signal cable to the
projector, environment around the projector, etc., the automatic adjustment
may not work correctly. In such a case, please choose DISABLE to
disable the automatic adjustment, and make adjustment manually.
GHOST
1. Select a color element of ghost using the buttons ◄/►.
2. Adjust the selected element using the buttons ▲/▼ to disappear ghost.
KEY LOCK
Using the buttons ▲/▼ turns on/off the key lock feature. When TURN ON is
selected, the buttons on the projector except the STANDBY/ON button are locked.
SERVICE
TURN ON
TURN OFF
• Please use to avoid a mischief and touching accidentally. This
function does not have any effect on the remote control.
FILTER MESSAGE
Use the ▲/▼ button to set the timer for the interval to show the
message for cleaning up the air filter.
50h
100h TURN OFF
200h
300h
After selecting “50h”, “100h”, “200h”, or “300h”, the message
“CLEAN THE AIR FILTER” will appear after the timer reaches the
interval time set by the menu. ( 38) When the “TURN OFF” is
chosen, the air filter cleaning message will not appear.
• Please check and clean the air filter periodically, even if there is no
message. If the air filter becomes to be blocked by dust or others,
the internal temperature will rise, which could cause malfunction, or
reduce the lifetime of the projector.
• It is recommended to choose “100h” in general. Please be careful
with the operating environment of the projector and the condition of
the air filter, especially when the “200h”, “300h or “TURN OFF” is
chosen.
FACTORY RESET
Selecting RESET using the button ▲ performs this function. By this function,
all the items in all of menus will collectively return to the initial setting. Note
that the items LAMP TIME, FILTER TIME and LANGUAGE are not reset.
RESET CANCEL
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Maintenance
Lamp
HIGH VOLTAGE
HIGH TEMPERATURE
HIGH PRESSURE
WARNING
►The projector uses a high-pressure mercury glass lamp. The lamp can break
with a loud bang, or burn out, if jolted or scratched, handled while hot, or worn
over time. Note that each lamp has a different lifetime, and some may burst or
burn out soon after you start using them. In addition, when the bulb bursts, it is
possible for shards of glass to fly into the lamp housing, and for gas containing
mercury to escape from the projector’s vent holes.
►About disposal of a lamp • This product contains a mercury lamp; do not
put it in a trash. Dispose of it in accordance with environmental laws.
For lamp recycling, go to www.lamprecycle.org. (in the US)
For product disposal, contact your local government agency or www.eiae.org (in
the US) or www.epsc.ca (in Canada).
For more information, call your dealer.
• If the lamp should break (it will make a loud bang when it does), unplug
the power cord from the outlet, and make sure to request a replacement
lamp from your local dealer. Note that shards of glass could damage the
inside of the projector, or cause injury during handling, so please do not
try to clean the projector or replace the lamp yourself.
Disconnect
the plug
from the
power
• If the lamp should break (it will make a loud bang when it does),
ventilate the room well, and make sure not to breathe the gas that
comes out of the projector vents, or get it in your eyes or mouth.
• Before replacing the lamp, turn the projector off and unplug the power
outlet
cord, then wait at least 45 minutes for the lamp to cool sufficiently.
Handling the lamp while hot can cause burns, as well as damaging the
lamp.
• Never unscrew except the appointed (marked by an arrow) screws.
• Do not open the lamp cover while the projector is suspended from
the ceiling. This is dangerous, since if the lamp’s bulb has broken, the
shards will fall out when the cover is opened. In addition, working in
high places is dangerous, so ask your local dealer to have the lamp
replaced even if the bulb is not broken.
• Do not use the projector with the lamp cover removed. To replace the
lamp, make sure that the screws are tightened firmly. Loose screws
could result in damage or injury.
• Use only the lamp of the specified type.
• If the lamp breaks soon after the first time it is used, it is possible
that there are electrical problems elsewhere besides the lamp. If this
happens, contact your local dealer or a service representative.
•
Handle with care: jolting or scratching could cause the lamp bulb to burst during use.
• Using the lamp for long periods of time, could cause it dark, not to light
up or to burst. When the pictures appear dark, or when the color tone
is poor, please replace the lamp as soon as possible. Do not use old
(used) lamps; this is a cause of breakage.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Lamp (continued)
A lamp has a finite product life. Using the lamp for long periods of time could
cause the pictures darker or the color tone poor. Note that each lamp has a
different lifetime, and some may burst or burn out soon after you start using them.
Preparation of a new lamp and early replacement are recommended.
To prepare a new lamp, contact your dealer and tell the lamp type number.
Type number = DT00731.
Turn the projector off, and unplug the power cord. Allow the lamp to cool for
at least 45 minutes.
1.
Prepare a new lamp.
If the projector is mounted on the ceiling, or if the lamp has broken, also ask
the dealer to replace the lamp.
2.
Lamp cover
In the case of replacement by yourself,
Loosen the lamp cover screw (marked by arrow)
3.
and then slide the lamp cover to the side to
remove it.
Loosen the 2 screws (marked by arrow) of the
lamp, and slowly pick up the lamp by the handles.
4.
Screw
Screws
Insert the new lamp, and retighten firmly the two
screws that are loosened in the previous process
to lock it in place.
5.
Slide the lamp cover back in place and firmly
fasten the lamp cover screws.
6.
Turn the projector on and reset the lamp time
using the LAMP TIME function in the OPTION
7.
( 38)
menu
.
Handle
(1) Press the MENU button to display a menu. Only
when the EASY MENU has appeared, please
perform the next step (2).
(2) Point at the “Go To Advance Menu …” in the menu
using ▼/▲ button, then press the ► button.
(3) Point at the “OPTION” in the left column of the
menu using ▼/▲ button, then press the ► button.
(4) Point at the ”LAMP TIME” using ▼/▲ button, then
press the ► button. A dialog will appear.
(5) Press the ▲ button to select “RESET” on the
dialog. It performs resetting the lamp time.
NOTE • Please reset the lamp time only when you have replaced the lamp,
for a suitable indication about the lamp.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Air filter
WARNING ►Before caring, make sure the power switch is off and the
power cable is not plugged in, then allow the projector to cool sufficiently. The
care in a high temperature state of the projector could cause an electric shock,
a burn and/or malfunction to the projector.
►Use only the air filter of the specified type. Do not use the projector with the
air filter and the filter cover removed. It could result in a fire and/or malfunction
to the projector.
►The air filter should be cleaned periodically. If the air filter becomes clogged
by dust or the like, internal temperatures rise and could cause a fire, a burn
and/or malfunction to the projector.
NOTE • Please replace the air filter when it is damaged or too soiled, and
also when you replace the lamp.
• Please reset the filter time only when you have cleaned or replaced the air
(
38)
filter, for a suitable indication about the air filter.
• The projector may display the message such as “CHECK THE AIR FLOW” or
turn off the projector, to prevent the internal heat level rising.
If the air filter becomes clogged by dust or the like, internal temperatures rise and
could cause a fire, a burn and/or malfunction to the projector. When the indicators
or a message prompts you to clean the air filter, clean the air filter as soon as
possible.
Please check and clean the air filter periodically, even if there is no message.
Please replace the air filter when it is damaged or too soiled. Preparation of a new
air filter is recommended.
To prepare a new air filter, contact your dealer and tell the air filter type number.
Type number = NJ22222
And also when you replace the lamp, please replace the air filter. An air filter of
specified type will come together with a replacement lamp for this projector.
Turn the projector off, and unplug the
power cord. Allow the lamp to cool for at
least 45 minutes.
1.
Handle
When the projector is suspended from
Filter cover
2.
the ceiling, apply the vacuum cleaner to
and around the filter cover first, to prevent
penetration of dust or the like.
While supporting the projector with one
3.
hand, use your other hand to pull the filter
cover forward in the direction of the arrow.
Remove the air filter.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Air filtre (continued)
Apply a vacuum cleaner to the air filter
and the filter cover. Please replace the air
filter when it is damaged or too soiled.
4.
Replace the air filter in its original
5.
position. Secure the air filter in place by
pressing each of the six locations.
Make sure there is no dust or dirt
remaining after the cover is in place. If any
dust or dirt remains use a vacuum cleaner
to remove it as when placing the filter
cover on the air filter.
Air filter’s
knob
Reattach the filter cover to the projector by
aligning the filter cover with the grooves
on the projector. While holding the handle,
push down on the filter cover until it locks
firmly in place.
mark
Air filter
Filter cover
Turn the projector on and reset the filter
6.
time using the FILTER TIME function in the
(
38)
.
OPTION menu
(1) Press the MENU button to display a menu. When the EASY MENU has
appeared, please skip the next step (2).
(2) Point at the “OPTION” in the left column of the menu using ▼/▲ button, then
press the ► button.
(3) Point at the “FILTER TIME” using ▼/▲ button, then press the ► button. A
dialog will appear.
(4) Press the ▲ button to select “RESET” on the dialog. It performs resetting the
lamp time.
Model 8755D-RJ Only!
Internal Clock Battery
Replacement of battery is discribed on page 45. The clock will not function
correctly when the battery is expended. A dead battery will cause the clock to
indicate wrong or stopped time.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Other care
WARNING ►Before caring, make sure the power switch is off and the
power cable is not plugged in, and then allow the projector to cool sufficiently.
The care in a high temperature state of the projector could cause a burn and/or
malfunction to the projector.
►Never try to care for the inside of the projector personally. Doing is so
dangerous.
►Avoid wetting the projector or inserting liquids in the projector. It could result
in a fire, an electric shock, and/or malfunction to the projector.
• Do not put a container containing water, cleaner or chemicals near the
projector.
• Do not use aerosols or sprays.
CAUTION ►Please take right care of the projector according to the
following. Incorrect care could cause not only an injury but adverse influence
such as discoloration, peeling paint, etc.
►Do not use cleaner or chemicals other than those listed below.
►Do not polish or wipe with hard objects.
Inside of the projector
In order to ensure the safe use of your projector, please have it cleaned and
inspected by your dealer about once every year.
Caring for the lens
If the lens is flawed, soiled or fogged, it could cause deterioration of display
quality. Please take care of the lens, being cautious of handling.
Turn the projector off, and unplug the power cord. Allow the projector to cool
sufficiently.
1.
After making sure that the projector is cool adequately, lightly wipe the lens
with a commercially available lens-cleaning wipe. Do not touch the lens
directly with your hand.
2.
Caring for the cabinet and remote control
Incorrect care could have adverse influence such as discoloration, peeling paint,
etc.
Turn the projector off, and unplug the power cord. Allow the projector to cool
sufficiently.
1.
After making sure that the projector is cool adequately, lightly wipe with gauze
or a soft cloth.
If soiling is severe, dip soft cloth in water or a neutral cleaner diluted in water,
and wipe lightly after wringing well. Then, wipe lightly with a soft, dry cloth.
2.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Replacing Internal Clock battery (8755D-RJ only!)
Consumption of the battery makes the clock not to work correctly. When the clock is wrong or it has
stopped, please replace the battery according to the following procedures.
WARNING ►Always handle the batteries with care and use them only as directed. Battery
may explode if mistreated. Do not recharge, disassemble or dispose of in fire.
And also improper use may result in cracking or leakage, which could result in fire, injury and/or
pollution of the surrounding environment.
•
Be sure to use only the batteries specified. Do not use batteries of different types at the same
time. Do not mix a new battery with used one.
Make sure the plus and minus terminals are correctly aligned when loading a battery.
If the battery is placed in the battery holder upside-down, it may be hard to remove.
•
•
•
•
•
Keep a battery away from children and pets. If swallowed consult a physician immediately for emergency treatment.
Do not short circuit or solder a battery.
Do not allow a battery in a fire or water. Keep batteries in a dark, cool and dry place.
If you observe a leakage of a battery, wipe out the flower and then replace a battery. If the liquid
adheres to your body or clothes, rinse well with water immediately.
Obey the local laws on disposing the battery.
•
Turn the projector off, and unplug the power cord. Allow the
1.
2.
3.
projector to cool sufficiently.
After making sure that the projector has cooled adequately,
slowly turn over the projector, so that the bottom is facing.
Remove the battery cover.
Turn the battery cover in the direction indicated “OPEN”
using such as coins. Then the battery cover will come up. While
removing the battery cover, pick its knob.
Battery Cover
OPEN
Take the old battery out.
Press the metal claw of the battery holder. Then the battery
will come up. Remove the battery.
4.
Knob
Metal claw
Put a new battery in.
5.
Replace battery with HITACHI MAXELL, Part No.CR2032
only. Use of another battery may present a risk of fire or
explosion.
“+” marking
Insert a new battery in the battery holder according to its minus terminal
as indicated in the battery holder, so that the side marked by
facing. And push the battery into the battery holder fully to fix.
+
is
CLOSE
Close the battery cover.
Replace the battery cover in place, then turn it in the
direction indicated “CLOSE” using such as coins, to fix.
6.
If the battery is placed in the battery holder upside-down, follow the procedure below to remove
and reload it properly.
1. Remove the battery cover as described in steps 1 through 3 above.
2. Turn the projector over again, so that the top of the projector is facing up.
3. While lifting the side of the projector closest to the lens, press the metal claw of the battery
holder. The battery will fall out of the holder, so be careful not to lose it.
4. Turn the projector over once more, so that the bottom faces up, and reload the battery correctly.
NOTE • The internal clock’s time will be reset when the battery is removed.
Please reconfigure the time via the menu or a web browser after replacing the battery.
(Please refer to page
- Network Functions: Date/Time Settings for more information.)
76
45
Download from Www.Somanuals.com. All Manuals Search And Download.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Related messages
When the unit's power is on, messages such as those shown below may be
displayed. When any such message is displayed on the screen, please follow the
instructions described below. If the same message is displayed after the remedy,
or if a message other than the following appears, please contact your dealer or
service company.
Although these messages will be automatically disappeared around several
minutes, it will be reappeared every time the power is turned on.
Message
Description
There is no input signal.
Please confirm the signal input connection, and the status
NO INPUT IS DETECTED
ON ***
of the signal source.
The horizontal or vertical wavelength of the input signal
is out of the response parameter range of this unit.
Please confirm the specs for your projector or the signal
source specs.
SYNC IS OUT OF RANGE
ON *** fH *****kHz fV *****Hz
The internal temperature is rising.
Please turn the power off, and allow the projector to cool
down at least 20 minutes. After having confirmed the
following items, please turn the power ON again.
• Is there blockage of the air passage aperture?
• Is the air filter dirty?
CHECK THE AIR FLOW
• Does the peripheral temperature exceed 35°C?
If the same indication is displayed after the remedy, please set
FAN SPEED of the SERVICE item in the OPTION menu to HIGH.
REMINDER
*** HRS PASSED AFTER THE
LAST FILTER CHECK.
FILTER MAINTENANCE IS ESSENTIAL
TO REMOVE WARNING MESSAGE,
RESET FILTER TIMER.
A note of precaution when cleaning the air filter.
Please immediately turn the power off, and clean or change
the air filter referring to the “Air Filter” section of this manual.
After you have cleaned or changed the air filter, please be
sure to reset the filter timer.
SEE MANUAL FURTHER INFO.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Regarding the indicator lamps
Lighting and flashing of the POWER indicator, the LAMP indicator, and the TEMP
indicator have the meanings as described in the table below. Please follow the
instructions within the table. If the same indication is displayed after the remedy,
or if an indication other than the following is displayed, please contact your dealer
or service company.
POWER
indicator indicator indicator
LAMP
TEMP
Description
Lighting
In Orange
Turned
off
Turned
off
The projector is in a standby state.
Please refer to the section “Power On/Off”.
Blinking
In Green
Turned
off
Turned
off
The projector is warming up.
Please wait.
Lighting
In Green
Turned
off
Turned
off
The projector is in an on state.
Ordinary operations may be performed.
Blinking
In Orange
Turned
off
Turned
off
The projector is cooling down.
Please wait.
The projector is cooling down. A certain error
has been detected.
Please wait until the POWER indicator finishes
blinking, and then perform the proper measure using
the item descriptions below.
Blinking
In Red
(discre- (discre-
tionary) tionary)
The lamp does not light, and there is a
possibility that interior portion has become
heated.
Please turn the power off, and allow the projector to
cool down at least 20 minutes. After the projector has
Lighting Turned sufficiently cooled down, please make confirmation of
Blinking
In Red
or
Lighting
In Red
In Red
off
the following items, and then turn the power on again.
• Is there blockage of the air passage aperture?
• Is the air filter dirty?
• Does the peripheral temperature exceed 35°C?
If the same indication is displayed after the remedy,
please change the lamp referring to the section “Lamp”.
The lamp cover has not been properly fixed.
Please turn the power off, and allow the projector to
cool down at least 45 minutes. After the projector has
sufficiently cooled down, please make confirmation
of the attachment state of the lamp cover. After
performing any needed maintenance, turn the power
on again. If the same indication is displayed after
the remedy, please contact your dealer or service
company.
Blinking
In Red
or
Lighting
In Red
Blinking Turned
In Red off
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Regarding the indicator lamps (continued)
POWER
indicator indicator indicator
LAMP
TEMP
Description
The cooling fan is not operating.
Please turn the power off, and allow the projector to
cool down at least 20 minutes. After the projector has
Turned Blinking sufficiently cooled down, please make confirmation
Blinking
In Red
or
Lighting
In Red
off
In Red that no foreign matter has become caught in the fan,
etc., and then turn the power on again.
If the same indication is displayed after the remedy,
please contact your dealer or service company.
There is a possibility that the interior portion
has become heated.
Please turn the power off, and allow the projector to
cool down at least 20 minutes. After the projector has
sufficiently cooled down, please make confirmation of
Blinking
In Red
or
Lighting
In Red
Turned Lighting the following items, and then turn the power on again.
off
In Red • Is there blockage of the air passage aperture?
• Is the air filter dirty?
• Does the peripheral temperature exceed 35°C?
If the same indication is displayed after the remedy,
please set FAN SPEED of the SERVICE item in the
OPTION menu to HIGH.
It is time to clean the air filter.
Please immediately turn the power off, and clean or
Lighting
In Green
Simultaneous
blinking in Red
change the air filter referring to the section “Air Filter”.
After cleaning or changing the air filter, please be sure
to reset the filter timer. After the remedy, reset the
power to ON.
NOTE • When the interior portion has become overheated, for safety
purposes, the power source is automatically turned off, and the indicator lamps
may also be turned off. In such a case, press the “” (OFF) side of the power
switch, and wait at least 45 minutes. After the projector has sufficiently cooled
down, please make confirmation of the attachment state of the lamp and lamp
cover, and then turn the power on again.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Phenomena that may be easy to be mistaken for machine defects
WARNING ►Never use the projector if abnormal operations such as
smoke, strange odor, excessive sound, damaged casing or elements or cables,
penetration of liquids or foreign matter, etc. should occur. In such cases,
immediately turn off the power switch and then disconnect the power plug from
the power outlet. After making sure that the smoke or odor has stopped, contact
your dealer or service company.
Before requesting repair, please check in
1.
accordance with the following chart. This
operation sometimes resolves your problem.
If the situation cannot be corrected,
The projector’s microprocessor may need to be
reset. Please push the Restart switch by using a cocktail stick or similar and
the projector will restart.
2.
Some setting may be wrong. Please use the FACTORY RESET function of the
3.
(
39)
to reset all settings to factory default.
SERVICE item in the OPTION menu
Then, if the problem is not removed after the remedy, please contact your dealer
or service company.
Reference
page
Phenomenon
Cases not involving a machine defect
The electrical power cord is not plugged in.
Correctly connect the power cord.
14
The power switch is not set to the on position.
17
17
Set the power switch to [ | ] (On).
The main power source has been interrupted during
operation such as by a power outage (blackout), etc.
Please turn the power off, and allow the projector to cool
down at least 2 minutes. After the projector has sufficiently
cooled down, please turn the power on again.
Power does not
come on.
Either there is no lamp and/or lamp cover, or either
of these has not been properly fixed.
Please turn the power off, and allow the projector to cool down
at least 45 minutes. After the projector has sufficiently cooled
down, please make confirmation of the attachment state of the
lamp and lamp cover, and then turn the power on again.
40, 41
The signal cables are not correctly connected.
12, 13
–
Correctly connect the connection cables.
Signal source does not correctly work.
Correctly set up the signal source device by referring to the
manual of the source device.
Neither sounds
nor pictures are
outputted.
The input changeover settings are mismatched.
Select the input signal, and correct the settings.
18
The RGB IN2 port is assigned to an RGB out while
an RGB input signal is inputted to the port.
Push the RGB IN OUT switch to switch the function of the port.
12
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Phenomena that may be easy to be mistaken for machine defects (continued)
Reference
Phenomenon
Cases not involving a machine defect
page
The signal cables are not correctly connected.
Correctly connect the audio cables.
12,13
The MUTE function is working.
Restore the sound pressing the MUTE or VOLUME button
on the remote control.
18
18
Sound does not
come out.
The volume is adjusted to an extremely low level.
Adjust the volume to a higher level using the menu function
or the remote control.
The AUDIO setting is not correct.
34
17
Correctly set the AUDIO item in the SETUP menu.
The lens cap is attached.
Remove the lens cover.
The signal cables are not correctly connected.
Correctly connect the connection cables.
12, 13
The brightness is adjusted to an extremely low level.
Adjust BRIGHTNESS to a higher level using the menu
function or the remote control.
No pictures are
displayed.
25
The computer cannot detect the projector as a plug
and play monitor.
11
22
Make sure that the computer can detect a plug and play
monitor using another plug and play monitor.
Video screen
display freezes.
The FREEZE function is working.
Press the FREEZE button to restore the screen to normal.
Color settings are not correctly adjusted.
Perform picture adjustments by changing the COLOR
TEMP, COLOR, TINT and/or COLOR SPACE settings,
using the menu functions.
25, 28,
32
Colors have a
faded- out
appearance, or
Color tone is
poor.
COLOR SPACE setting is not suitable.
Change the COLOR SPACE setting to AUTO, RGB,
SMPTE240, REC709 or REC601.
32
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Phenomena that may be easy to be mistaken for machine defects (continued)
Reference
page
Phenomenon
Cases not involving a machine defect
The brightness and/or contrast are adjusted to an
extremely low level.
Adjust BRIGHTNESS and/or CONTRAST settings to a
higher level using the menu function.
25
Pictures appear
dark.
The WHISPER function is working.
Select NORMAL for the WHISPER item in the SETUP
menu.
25
The lamp is approaching the end of its product
40, 41
lifetime.
Replace the lamp.
Either the focus and/or horizontal phase settings are
not properly adjusted.
30
44
Adjust the focus using the focus ring, and/or H PHASE
using the menu function.
Pictures appear
blurry.
The lens is dirty or misty.
Clean the lens referring to the section “Caring for the lens”.
NOTE • Although bright spots or dark spots may appear on the screen, this
is a unique characteristic of liquid crystal displays, and it does not constitute or
imply a machine defect.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty And After-Service
Warranty and after-service
If a problem occurs with the equipment, first refer to the “Troubleshooting” and run
through the suggested checks. If this does not resolve the problem, please contact your
dealer or service company. They will tell you what warranty condition is applied.
Specifications
Specifications
NOTE • These specifications are subject to change without notice.
Item
Specification
Product name
Liquid crystal projector
1.5 cm (0.6 type)
Panel size
Liquid
Crystal
panel
Drive system TFT active matrix
8065: 480,000 pixels (800 horizontal x 600 vertical)
Pixels
8755D: 786,432 pixels (1024 horizontal x 768 vertical)
Lens
Zoom lens F=1.7 ~ 1.9 f=18.9 ~ 22.6 mm
Lamp
180W UHB
Speaker
1W x 1
Power Supply
AC100-120V/3.1A, AC220-240V/1.7A
290W
Power Consumption
Temperature range
5 ~ 35°C (Operating)
306 (W) x 86 (H) x 249 (D) mm
(Not including protruding parts)
• Please refer to the following figure.
Size
Weight (mass)
3.0 kg
RGB input:
Video input:
RGB IN1..D-sub 15pin mini x1 COMPONENT VIDEO
RGB IN2 /OUT
(Y, CB/PB, CR/PR)...... RCA x3
D-sub 15pin mini ................x1 S-Video ................................ 1
(select RGB IN2 or RGB OUT) Video .................................... 1
Ports
Audio input:
Communication port:
AUDIO 1.......... Stereo mini x1 CONTROL............D-sub 9pin x1
AUDIO 2..................... RCA x2 USB....................... USB(B) x1
8755D-RJ
Audio output:
LAN . . . . . . . . . . . . . . . RJ-45 x 1
AUDIO OUT ... Stereo mini x1
Lamp
DT00731
Optional
Air filter
parts
NJ22222
Others
• Please consult your dealer.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Specifications (continued)
S - V I D E O
V I D E O
R
B
P
/
R
C
A U D I O I N 1
K
L
P /
B
C
T
2
R G B O U
R G B I N
1
A U D I O O U T
C O N T R O L
B
U S
R G B I N
R Y
A U D I O I N 2
306 mm
54
Download from Www.Somanuals.com. All Manuals Search And Download.
P8r7oje5c5toDr -RJ only
Network Functions
This section is only intended to explain Network Functions.
Contents
Network Menu .......................................................................
56
Network Functions ............................................................... 59
Settings ................................................................................ 64
Projector Control .................................................................. 79
Failure & Warning Alerts via E-mail..................................... 83
Projector Management via SNMP......................................... 85
Controlling the Projector via Scheduling............................. 86
e-Shot (Still Image Transfer) Display ................................... 89
Command Control via the Network...................................... 91
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Multifunctional settings
NETWORK Menu
8755D-RJ only! (LAN)
ꢀMENUꢀ[RGB]
:SELECT
Select [Network] from the main menu to access the following
functions.
ꢀ
DHCP
ꢀ
TURNꢀOFF
ꢀPICTURE
ꢀIMAGE
ꢀINPUT
ꢀ
ꢀ
IPꢀADDRESS
SUBNETꢀMASK
ꢀDEFAULTꢀGATEWAY
DATEꢀANDꢀTIME
ꢀSETUP
ꢀ
ꢀSCREEN
ꢀOPTION
ꢀNETWORK
ꢀEASYꢀMENU
ꢀTIMEꢀDIFFERENCE
ꢀe‑SHOT
ꢀ
INFORMATION
NOTE • The factory default setting for DHCP is “TURN ON”. There is no need to set
up [DHCP], [IP ADDRESS], [SUBNET MASK] or [DEFAULT GATEWAY] if your network
has DHCP enabled. ( User’s Manual - Network Functions)
• If you are not utilizing SNTP ( User’s Manual - Network Functions), then you must
set the DATE AND TIME during the initial installation. Please refer to the item DATE AND
TIME on the following list.
NOTE Consult with your network administrator before connecting to an existing
access point on your network. Incorrect network settings on this projector may cause
trouble on the network.
Item
Operation
DHCP TURN ON/TURN OFF:
DHCP
DHCP
TURNꢀON
TURNꢀOFF
Use the ▲/▼ buttons to turn DHCP on/off
TURN ON TURN OFF
(Dynamic Host
Configuration
Protocol)
Select TURN OFF when the network does not have DHCP
enabled.
Entering the IP ADDRESS :
192. 168. 1. 254
IPꢀADDRESS
Use the ▲/▼/◄/► buttons to enter the IP
ADDRESS. This function can only be used
when DHCP is set to “TURN OFF”.
IP ADDRESS
~Note~
The IP ADDRESS is the number that identifies this projector on the
network. You cannot have two devices with the same IP ADDRESS
on the same network.
Entering the SUBNET MASK :
Use the buttons ▲/▼/◄/► to enter the
255. 255. 255.
0
SUBNETꢀMASK
SUBNET MASK same SUBNET MASK used by your PC.
This function can only be used when DHCP
is set to “TURN OFF”.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Multifunctional settings
NETWORK Menu (continued)
Item
Operation
Entering the DEFAULT GATEWAY :
0. 0. 0.
0
Use the ▲/▼/◄/► buttons to enter the DEFAULT
GATEWAY (therouter or PC that forwardstraffic to a
destination outside of the subnet of the transmitting
device) address.This function can only be used
when DHCP is set to “TURN OFF”.
DEFAULTꢀGATEWAY
DEFAULT
GATEWAY
Entering DATE AND TIME :
Use the ▲/▼/◄/► buttons to enter the Year (last two digits),
Month, Date, Hour and Minute.
~Note~
DATE AND TIME
The projector will override this setting and retrieve DATE AND TIME
information from the Timeserver when SNTP is enabled. See [Date/
Time Settings] in [User’s Manual - Network Functions: Configuring
and Controlling the Projector via a Web Browser] for SNTP settings.
Entering the TIME DIFFERENCE :
Use the ◄/► buttons to enter the
TIME DIFFERENCE.
TIMEꢀDIFFERENCE
TIME
DIFFERENCE
Set the same TIME DIFFERENCE
as the one set on your PC. If unsure,
consult your network administrator.
Use the ▲ button to return to the menu
after setting the TIME DIFFERENCE.
GMTꢀ00:00
e-SHOT display :
Use the ▲/▼ buttons to select an item and the ► or ENTER
buttons to display the image.
Image1
Image2
e‑SHOT
IMAGE‑1
IMAGE‑2
IMAGE‑3
IMAGE‑4
Image3
Image4
Once an image is displayed, you can
use the ▲/▼ buttons to page through
the images. Use the ◄ or ESC buttons
to return to the menu.
e-SHOT
Pressing the RESET button on the
remote control while an image is being
IMAGE‑1
displayed will display the RESET menu.
The displayed image can be deleted
ꢀe‑SHOT
from the RESET menu using the
ENTER button on the remote control or
the INPUT button on the projector.
ꢀꢀRESETꢀ:ꢀIMAGE‑1
ꢀ,ꢀ+ꢀ:NOꢀꢀꢀ,ꢀꢀ:YES
ESC ENTER
If you do not wish to delete the image use the ESC button on the remote
control or push the
◄
and INPUT buttons on the projector at the same time.
~Note~
•
•
Items with no image stored cannot be selected.
Images can be changed using the ▲/▼ buttons while the image data downloads.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Multifunctional settings
NETWORK Menu (continued)
Item
Operation
INFORMATION display :
Use the ► or ENTER buttons to view
network information and confirm settings.
NETWORK‑INFORMATION
NAME
IPꢀADDRESSꢀꢀꢀꢀꢀꢀꢀ192.168.1.254
SUBNETMASKꢀꢀꢀꢀꢀꢀꢀ255.255.255.0
DEFAULTꢀGATEWAYꢀꢀ0.0.0.0
MACꢀADDRESS
00:00:87:56:AC:7C
DATEꢀANDꢀTIMEꢀꢀꢀꢀꢀ2ꢀ0ꢀ0ꢀ0ꢀ/ꢀ1ꢀ/ꢀ1ꢀ 8:15
TIMEꢀDIFFERENCEꢀꢀGMTꢀ00:00
INFORMATION
~Note~
• Only the first 16 characters of the projector name are displayed.
• The battery for the built in clock may be dead if the clock loses
time even when the DATE AND TIME have been set correctly.
Replace the battery by following the instructions on replacing the
battery. ( 47)
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Network Functions
Network Functions
8755D-RJ only
This projector is equipped with the following network functions.
Configuring and Controlling the Projector via a Web Browser
You can change the settings of or control the projector via a network by using a
web browser from a PC that is connected to the same network.
4)
Failure & Warning Alerts via E-mail
The projector can automatically send an alert to specified e-mail addresses when
the projector requires maintenance or has encountered an error.
Projector Management via SNMP
This projector is SNMP (Simple Network Management Protocol) compliant,
allowing you to monitor it from a remote location using SNMP software. In
addition, the projector is able to send failure & warning alerts to a specified PC.
Controlling the Projector via Scheduling
You can schedule the projector to perform various functions according to the
DATE and TIME.
Still Image Transfer
The projector can display still images that are transferred via the network.
Projector Control via RS-232C via the Network
The projector can be controlled using RS-232C commands over a network.
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Network Functions Notes:
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Network Functions
Before using the network functions…
To use the network functions of this projector, the projector must be configured to
suit your network. Consult with your network administrator before connecting the
projector to your network. Incorrect network configuration of this projector may
cause problems on your network.
Connect to the Gateway (The router/PC that forwards traffic to a destination
outside of the subnet of the transmitting device) from the network terminal on the
projector using a CAT-5 cable and configure the following settings.
If using a network with DHCP enabled:
The projector’s network settings can be configured automatically. when [DHCP]
on the network menu is set to [TURN ON]. Please refer to DHCP in network
menu. (User's Manual - Operating Guide : NETWORK Menu) If a fixed / static IP
address is required, please configure your projector according to the steps in the
following section.
If using a network system that does not have DHCP enabled or if
using a fixed IP address on a network system equipped with DHCP
enabled:
Configure the following settings on the network menu.
(User's Manual - Operating Guide : NETWORK Menu)
1. [DHCP]: Disable DHCP (Set [DHCP] to [TURN OFF]).
[IP ADDRESS]: Enter an appropriate IP address for the projector to connect
to your network.
2.
[SUBNET MASK]: Enter an appropriate SUBNETMASK for the projector to
connect to your network.
3.
[DEFAULT GATEWAY]: Enter an appropriate Gateway (the router/PC that
forwards traffic to a destination outside of the subnet of the transmitting
device) address for the projector to connect to your network.
4.
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Configuring and controlling the projector via a web browser
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Network Functions
Configuring and controlling the projector via a web browser (Continued)
When configuring or controlling the projector via a web browser, an ID and
password are required. There are two types of IDs, Administrator IDs and User
IDs. The following chart describes the differences between user and administrator
IDs.
Item
Description
Administrator ID User ID
Displays the projector’s current
network configuration settings.
Network Information
√
√
√
√
√
√
√
√
Displays and configures network
settings.
Network Settings
Port Settings
N/A
N/A
N/A
N/A
N/A
N/A
Displays and configures
communication port settings.
Displays and configures e-mail
addressing settings.
Mail Settings
Displays and configures failure &
warning alerts.
Alert Settings
Displays and configures schedule
settings.
Schedule Settings
Date/Time Settings
Displays and configures the date and
time settings.
Displays and configures passwords
and other security settings.
Security Settings
Projector Control
Projector Status
√
√
√
N/A
√
Controls the projector.
Displays and configures the current
projector status.
√
Restarts the projector’s network
connection.
Network Restart
√
N/A
Below are the factory default settings for administrator IDs, user IDs and
passwords.
Item
Administrator ID
User ID
ID
Password
<blank>
Administrator
User
<blank>
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings
Settings
Refer to the following for configuring or controlling the projector via a web browser.
Example: If the IP address of the projector is set to 192.168.1.10:
Fig. 1
1) Enter
[https://192.168.1.10] into the
address bar of the web browser and
the screen in Fig. 1 will be displayed.
2) Enter your ID and password and click
[Logon].
If the logon is successful either the Fig.2 or Fig.3 screen will be displayed.
Fig. 2 (Logon with administrator ID)
Fig. 3 (Logon with user ID)
3) Click the desired operation or configuration item on the main menu located on
the left-hand side of the screen (Fig. 2 or Fig. 3).
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings
Network Information
All screen images displayed in this manual are
screens of a logon using an administrator ID.
Any administrator only functions will not be
displayed when using a user ID. Refer to the
descriptions in each table.
Displays the projector’s current network configuration settings.
Item
Description
Displays the DHCP configuration settings.
Displays the current IP address.
Displays the Subnet Mask.
DHCP
IP Address
Subnet Mask
Default Gateway
MAC Address
Displays the Default Gateway.
Displays the MAC address.
Displays the network firmware time stamp. This information is only
displayed when logged on using an administrator ID.
Firmware Date
Displays the network firmware version number. This information is
only displayed when logged on using an administrator ID.
Firmware Version
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings
Network Settings
Displays and configures network settings.
Item
Description
Configures network settings.
IP Configuration
DHCP ON
Enables DHCP.
Disables DHCP.
DHCP OFF
IP Address
Configures the IP address when DHCP is disabled.
Configures the Subnet Mask when DHCP is disabled.
Configures the Default Gateway when DHCP is disabled.
Configures the Projector name.
Subnet Mask
Default Gateway
Projector Name
SysLocation
Configures the location to be referred to when using SNMP.
Configures the contact information to be referred to when
using SNMP.
SysContact
Click the [Apply] button to save the settings.
NOTE • The new configuration settings are activated after restarting the
network connection. When the configuration settings are changed, you must
restart the network connection. You can restart the network connection by
clicking [Network Restart] on the main menu.
• If you connect the projector to an existing network, consult a network
administrator before setting server addresses.
66
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings
Port Settings
Displays and configures communication port settings.
Item
Description
Network Control Port1
(Port:23)
Configures command control port 1 (Port:23).
Port open
Click the [Enable] check box to use port 23.
Click the [Enable] check box when authentication is required
for this port.
Authentication
Network Control Port2
(Port:9715)
Configures command control port 2 (Port:9715).
Port open
Click the [Enable] check box to use port 9715.
Click the [Enable] check box when authentication is required
for this port.
Authentication
Image Transfer Port
(Port:9716)
Configures the image transfer port (Port:9716).
Port open
Click the [Enable] check box to use port 9716.
Click the [Enable] check box when authentication is required
for this port.
Authentication
SNMP Port
Port open
Configures the SNMP port.
Click the [Enable] check box to use SNMP.
Configures the destination of the SNMP Trap in IP format.
Configures the SMTP port.
Trap address
SMTP Port
Port open
Click the [Enable] check box to use the e-mail function.
Click the [Apply] button to save the settings.
NOTE • The new configuration settings are activated after restarting the
network connection. The network connection must be restarted when the
configuration settings are changed. The network connection can be restarted
using [Network Restart] on the main menu.dresses.
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings
Mail Settings
Displays and configures e-mail addressing settings.
Item
Description
Click the [Enable] check box to use the e-mail function.
Configure the conditions for sending email under [Alert
Settings].
Send Mail
SMTP Server IP Address Configures the address of the mail server in IP format.
Configures the sender e-mail address.
The length of the sender e-mail address can be up to 255
alphanumeric characters.
Sender E-mail address
Configures the e-mail address of up to five recipients. You
can also specify [TO] or [CC] for each address. The length of
the recipient e-mail address can be up to 255 alphanumeric
characters.
Recipient E-mail address
Click the [Apply] button to save the settings.
NOTE • You can confirm whether the mail settings work correctly using the
[Send Test Mail] button.
• If you connect the projector to an existing network, consult a network
administrator before setting server addresses.
68
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings
Alert Settings
Displays and configures failure & warning alerts.
Item
Description
Configures Cover Error alert settings.
Cover Error
Click the [Enable] check box to enable SNMP Trap alerts for
this item.
SNMP Trap
Click the [Enable] check box to enable e-mail alerts for this
item.
Send Mail
Configures the subject line of the e-mail to be sent.
The length of the subject line can be up to 255 alphanumeric
characters.
Mail Subject
Configures the text of the e-mail to be sent.
The length of the text can be up to 1024 alphanumeric
characters.
Mail Text
Fan Error
Configures Fan Error alert settings.
Click the [Enable] check box to enable SNMP Trap alerts for
this item.
SNMP Trap
Click the [Enable] check box to enable e-mail alerts for this
item.
Send Mail
Configures the subject line of the e-mail to be sent.
The length of the subject line can be up to 255 alphanumeric
characters.
Mail Subject
Configures the text of the e- mail to be sent.
The length of the text can be up to 1024 alphanumeric
characters.
Mail Text
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings
Alert Settings (Continued)
Item
Description
Lamp Error
Configures Lamp Error alert settings.
Click the [Enable] check box to enable SNMP Trap alerts for
this item.
SNMP Trap
Click the [Enable] check box to enable e-mail alerts for this
item.
Send Mail
Configures the subject line of the e-mail to be sent.
The length of the subject line can be up to 255 alphanumeric
characters.
Mail Subject
Configures the text of the e-mail to be sent.
The length of the text can be up to 1024 alphanumeric
characters.
Mail Text
Temp Error
Configures Temp Error alert settings.
Click the [Enable] check box to enable SNMP Trap alerts for
this item.
SNMP Trap
Send Mail
Click the [Enable] check box to enable e-mail alerts for this
item.
Configures the subject line of the e-mail to be sent.
The length of the subject line can be up to 255 alphanumeric
characters.
Mail Subject
Mail Text
Configures the text of the e-mail to be sent.
The length of the text can be up to 1024 alphanumeric
characters.
Air Flow Error
SNMP Trap
Configures Air Flow Error alert settings.
Click the [Enable] check box to enable SNMP Trap alerts for
this item.
Click the [Enable] check box to enable e-mail alerts for this
item.
Send Mail
Configures the subject line of the e-mail to be sent.
The length of the subject line can be up to 255 alphanumeric
characters.
Mail Subject
Configures the text of the e-mail to be sent.
The length of the text can be up to 1024 alphanumeric
characters.
Mail Text
70
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings
Alert Settings (Continued)
Item
Description
Configures Lamp Time Error alert settings.
Lamp Time Error
Click the [Enable] check box to enable SNMP Trap alerts for
this item.
SNMP Trap
Click the [Enable] check box to enable e-mail alerts for this
item.
Send Mail
Configures the subject line of the e-mail to be sent.
The length of the subject line can be up to 255 alphanumeric
characters.
Mail Subject
Configures the text of the e-mail to be sent.
The length of the text can be up to 1024 alphanumeric
characters.
Mail Text
Cool Error
SNMP Trap
Configures Cool Error alert settings.
Click the [Enable] check box to enable SNMP Trap alerts for
this item.
Click the [Enable] check box to enable e-mail alerts for this
item.
Send Mail
Configures the subject line of the e-mail to be sent.
The length of the subject line can be up to 255 alphanumeric
characters.
Mail Subject
Configures the text of the e-mail to be sent.
The length of the text can be up to 1024 alphanumeric
characters.
Mail Text
Filter Error
SNMP Trap
Configures Filter Error alert settings.
Click the [Enable] check box to enable SNMP Trap alerts for
this item.
Click the [Enable] check box to enable e-mail alerts for this
item.
Send Mail
Configures the subject line of the e-mail to be sent.
The length of the subject line can be up to 255 alphanumeric
characters.
Mail Subject
Configures the text of the e-mail to be sent.
The length of the text can be up to 1024 alphanumeric
characters.
Mail Text
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings
Alert Settings (Continued)
Item
Description
Other Error
Configures Other Error alert settings.
Click the [Enable] check box to enable SNMP Trap alerts for
this item.
SNMP Trap
Click the [Enable] check box to enable e-mail alerts for this
item.
Send Mail
Configures the subject line of the e-mail to be sent.
The length of the subject line can be up to 255 alphanumeric
characters.
Mail Subject
Configures the text of the e-mail to be sent.
The length of the text can be up to 1024 alphanumeric
characters.
Mail Text
Schedule Execution Error Configures Schedule Execution Error alert settings.
Click the [Enable] check box to enable SNMP Trap alerts for
this item.
SNMP Trap
Click the [Enable] check box to enable e-mail alerts for this
item.
Send Mail
Configures the subject line of the e-mail to be sent.
The length of the subject line can be up to 255 alphanumeric
characters.
Mail Subject
Mail Text
Configures the text of the e-mail to be sent.
The length of the text can be up to 1024 alphanumeric
characters.
Lamp Time Alarm
SNMP Trap
Configures Lamp Time Alarm alert settings.
Click the [Enable] check box to enable SNMP Trap alerts for
this item.
Click the [Enable] check box to enable e-mail alerts for this
item.
Send Mail
Configures the subject line of the e-mail to be sent.
The length of the subject line can be up to 255 alphanumeric
characters.
Mail Subject
Configures the text of the e-mail to be sent.
The length of the text can be up to 1024 alphanumeric
characters.
Mail Text
72
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings
Alert Settings (Continued)
Item
Description
Configures Filter Time Alarm alert settings.
Filter Time Alarm
Click the [Enable] check box to enable SNMP Trap alerts for
this item.
SNMP Trap
Click the [Enable] check box to enable e-mail alerts for this
item.
Send Mail
Configures the subject line of the e-mail to be sent.
The length of the subject line can be up to 255 alphanumeric
characters.
Mail Subject
Configures the text of the e-mail to be sent.
The length of the text can be up to 1024 alphanumeric
characters.
Mail Text
“CHANGE THE LAMP” is Configures alert settings for when “CHANGE THE LAMP” is
displayed
displayed.
Click the [Enable] check box to enable SNMP Trap alerts for
this item.
SNMP Trap
Click the [Enable] check box to enable e-mail alerts for this
item.
Send Mail
Configures the subject line of the e-mail to be sent.
The length of the subject line can be up to 255 alphanumeric
characters.
Mail Subject
Configures the text of the e-mail to be sent.
The length of the text can be up to 1024 alphanumeric
characters.
Mail Text
Cold Start
Configures Cold Start alert settings.
Click the [Enable] check box to enable SNMP Trap alerts for
this item.
SNMP Trap
Authentication Failure
SNMP Trap
Configures Authentication Failure alert settings.
Click the [Enable] check box to enable SNMP Trap alerts for
this item.
Click the [Apply] button to save the settings.
73
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings
Schedule Settings
Displays and configures schedule settings.
Item
Description
Daily
Schedule
Schedule List
Sunday
Configures the daily schedule.
Click the [Enable] check box to enable daily scheduling.
Displays the current daily schedule.
Configures the Sunday schedule.
Schedule
Click the [Enable] check box to enable Sunday scheduling.
Displays the current Sunday schedule.
Schedule List
Monday
Configures the Monday schedule.
Schedule
Click the [Enable] check box to enable Monday scheduling.
Displays the current Monday schedule.
Schedule List
Tuesday
Configures the Tuesday schedule.
Schedule
Click the [Enable] check box to enable Tuesday scheduling.
Displays the current Tuesday schedule.
Schedule List
Wednesday
Configures the Wednesday schedule.
Schedule
Click the [Enable] check box to enable Wednesday scheduling.
Displays the current Wednesday schedule.
Configures the Thursday schedule.
Schedule List
Thursday
Schedule
Click the [Enable] check box to enable Thursday scheduling.
Displays the current Thursday schedule.
Schedule List
Friday
Configures the Friday schedule.
Schedule
Click the [Enable] check box to enable Friday scheduling.
Displays the current Friday schedule.
Schedule List
Saturday
Configures the Saturday schedule.
Schedule
Click the [Enable] check box to enable Saturday scheduling.
Displays the current Saturday schedule.
Schedule List
74
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings
Schedule Setting (Continued)
Item
Description
Configures the specific date (No.1) schedule.
Specific date No1
Click the [Enable] check box to enable specific date (No.1)
scheduling.
Schedule
Month/Day
Schedule List
Configures the Month and date.
Displays the current specific date (No.1) schedule.
Configures the specific date (No.2) schedule.
Specific date No.2
Click the [Enable] check box to enable specific date (No.2)
scheduling.
Schedule
Month/Day
Schedule List
Configures the Month and date.
Displays the current specific date (No.2) schedule.
Configures the specific date (No.3) schedule.
Specific date No.3
Click the [Enable] check box to enable specific date (No.3)
scheduling.
Schedule
Month/Day
Schedule List
Configures the Month and date.
Displays the current specific date (No.3) schedule.
Configures the specific date (No.4) schedule.
Specific date No.4
Click the [Enable] check box to enable specific date (No.4)
scheduling.
Schedule
Month/Day
Schedule List
Configures the Month and date.
Displays the current specific date (No.4) schedule.
Configures the specific date (No.5) schedule.
Specific date No.5
Click the [Enable] check box to enable specific date (No.5)
scheduling.
Schedule
Month/Day
Set the Month and date.
Schedule List
Displays the current specific date (No.5) schedule.
Click the [Apply] button to save the settings.
75
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings
Schedule Setting (Continued)
To add additional functions and events click the [Add] button and set the following
items.
Item
Description
Time
Configures the time to execute commands.
Configures the commands to be executed.
Configures the parameters for power control.
Command
Power Parameter
Input Source
Parameter
Configures the parameters for input switching.
Display Image
Parameter
Configures the parameters for display of transfer image data.
Click the [Register] button to add new commands to the Schedule List.
Click the [Delete] button to delete commands from the Schedule list.
Date/Time Settings
Displays and configures the date and time settings.
Item
Current Date
Description
Configures the current date in Year/Month/Day format.
Configures the current time in Hour:Minute:Second format.
Current Time
76
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings
Date/Time Settings (Continued)
Item
Description
Click the [ON] check box to enable daylight savings time and
set the following items.
Daylight Savings Time
Start
Configures the date and time daylight savings time begins.
Configures the month daylight savings time begins (1~12).
Month
Configures the week of the month daylight savings time
begins (First, 2, 3, 4, Last).
Week
Day
Configures the day of the week daylight savings time begins
(Sun, Mon, Tue, Wed, Thu, Fri, Sat).
Hour
Minute
End
Configures the hour daylight savings time begins (0 ~ 23).
Configures the minute daylight savings time begins (0 ~ 59).
Configures the date and time daylight savings time ends.
Configures the month daylight savings time ends (1 ~ 12).
Month
Configures the week of the month daylight savings time ends
(First, 2, 3, 4, Last).
Week
Day
Configures the day of the week daylight savings time ends
(Sun, Mon, Tue, Wed, Thu, Fri, Sat).
Hour
Configures the hour daylight savings time ends (0 ~ 23).
Configures the minute daylight savings time ends (0 ~ 59).
Minute
Configures the time difference (hours:minutes).
Set the same time difference as the one set on your PC. If
unsure, consult your network administrator.
Time difference
Click the [ON] check box to retrieve Date and Time
information from the SNTP server and set the following items.
SNTP
SNTP Server IP Address Configures the SNTP server address in IP format.
Configures the interval at which to retrieve Date and Time
information from the SNTP server. (hours:minutes).
Cycle
Click the [Apply] button to save the settings.
NOTE • The new configuration settings are activated after restarting the network connection.
The network connection must be restarted when the configuration settings are changed, The
network connection can be restarted using [Network Restart] on the main menu.
• If you connect the projector to an existing network, consult a network
administrator before setting server addresses.
• To enable the SNTP function, the time difference must be set.
• The projector will retrieve DATE and TIME information from the Timeserver
and override time settings when SNTP is enabled.
• The Internal Clock’s time may not remain accurate. Using SNTP is
recommended to maintain accurate time.
77
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings
Security Settings
Displays and configures passwords and other security settings.
Item
Description
Administrator authority Configures the Administrator ID and Password.
Configures the Administrator ID.
The length of the text can be up to 32 alphanumeric
characters.
Administrator ID
Configures the Administrator Password.
The length of the text can be up to 255 alphanumeric
characters.
Administrator
Password
Re-enter Administrator
Password
Re-enter the above password for verification.
User authority
Configures the User ID and Password.
Configures the User ID.
The length of the text can be up to 32 alphanumeric
characters.
User ID
Configures the User Password.
The length of the text can be up to 255 alphanumeric
characters.
User Password
Re-enter User
Password
Used to re-enter the above password for verification.
Configures the Authentication Password for the command
control.
Network Control
Configures the Authentication Password.
The length of the text can be up to 16 alphanumeric
characters.
Authentication
Password
Re-enter Authentication
Password
Used to re-enter the above password for verification.
Configures the community name if SNMP is used.
SNMP
Configures the community name.
The length of the text can be up to 64 alphanumeric
characters.
Community Name
Click the [Apply] button to save the settings.
NOTE • The new configuration settings are activated after restarting the
network connection. The network connection must be restarted when the
configuration settings are changed. The network connection can be restarted
using [Network Restart] on the main menu.
78
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector Control
Projector Control
Projector Control
The items shown in the table below can be
performed using the [Projector Control] menu.
Select an item using the up and down arrow keys
on the PC.
Most of the items have a submenu.
Refer to the table below for details.
Controls the projector.
Item
Main
Description
Power
Turns the power On/Off.
Input Source
Picture Mode
Blank On/Off
Mute
Selects the input source.
Selects the Picture Mode setting.
Turns Blank On/Off.
Turns Mute On/Off.
Freeze
Selects the Freeze setting.
Controls the Magnify setting.
Magnify
Picture
Brightness
Contrast
Adjusts the Brightness setting.
Adjusts the Contrast setting.
Selects the Gamma setting.
Selects the Color Temp setting.
Adjusts the Color setting.
Gamma
Color Temp
Color
Tint
Adjusts the Tint setting.
Sharpness
Progressive
MyMemory Recall
MyMemory Save
Adjusts the Sharpness setting.
Selects the Progressive setting.
Recalls the MyMemory data.
Saves the MyMemory data.
79
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector Control
Projector Control (Continued)
Item
Description
Image
Aspect
Selects the Aspect setting.
Selects the Over Scan setting.
Over Scan
V Position
H Position
H Phase
Adjusts the V Position.
Adjusts the H Position.
Adjusts the H Phase.
Adjusts the H Size.
H Size
Auto Adjust
Performs Auto Adjustment.
Input
Color Space
Component
Video Format
Frame Lock
Selects the Color Space.
Selects the Component terminal setting.
Selects the Video Format setting.
Enables/Disables Frame Lock.
Setup
Keystone
Adjusts the Keystone setting.
Whisper
Selects the Fan speed. (Normal or Whisper)
Selects the Mirror status.
Mirror
Volume
Adjusts the Volume setting.
Audio-RGB1
Audio-RGB2
Audio-Video
Audio-S-Video
Audio-Component
Assigns the Audio-RGB1 input terminal.
Assigns the Audio-RGB2 input terminal.
Assigns the Audio-Video input terminal.
Assigns the Audio-S-Video input terminal.
Assigns the Audio-Component input terminal.
Screen
Language
Selects the Language for the OSD.
Adjusts the vertical Menu Position.
Adjusts the horizontal Menu Position.
Adjusts the OSD Brightness level.
Selects the Blank mode.
Menu Position V
Menu Position H
OSD Bright.
Blank
Startup
Selects the Startup screen mode.
Turns MyScreen Lock On/Off.
MyScreen Lock
Message
Turns the Message function On/Off.
80
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector Control
Projector Control (Continued)
Item
Description
Option
Auto Search
Turns the Automatic signal search function On/Off.
Configures the timer to shut off the projector when no signal
is detected.
Auto Power off
Auto Adjust Enable
Enables/Disables Auto Adjustment.
Projector Status
Displays and configures the current projector status.
Item
Error Status
Description
Displays the current error status
Lamp Time
Filter Time
Power Status
Input Status
Blank On/Off
Mute
Displays the usage time for the current lamp.
Displays the usage time for the current filter.
Displays the current power status.
Displays the current input signal source.
Displays the Blank On/Off status.
Displays the current Mute On/Off status.
Displays the current Freeze On/Off status.
Displays the current RGB2 terminal In/Out setting.
Freeze
RGB2 Status
81
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector Control
Network Restart
Restarts the projector’s network connection.
Item
Description
Restarts the projector’s network connection in order to
activate new configuration settings.
Restart
NOTE • Restarting requires you to re-log on in order to further control or
configure the projector via a web browser.
Logoff
When logoff is clicked, the logon screen is displayed.
82
Download from Www.Somanuals.com. All Manuals Search And Download.
Failure & Warning Alerts via E-mail
Failure & Warning Alerts via E-mail
The projector can automatically send an alert to specified e-mail addresses when
the projector requires maintenance or has encountered an error.
NOTE • Up to five e-mail addresses can be specified.
• The projector may be not able to send e-mail if the projector suddenly loses
power.
Mail Settings
To use the projector’s e-mail function please configure the following items via a
web browser.
Example: If the IP address of the projector is set to 192.168.1.10:
1) Enter [https://192.168.1.10] into the address bar of the web browser.
2) Enter the Administrator ID and Password and click [Logon].
3) Click [Port Settings] on the main menu.
4) Click the [Enable] check box to open the SMTP Port.
5) Click the [Apply] button to save the settings.
NOTE • A Network Restart is required after the SMTP Port configuration
settings have changed. Click [Network Restart] and configure the following
items.
6) Click [Mail Settings] and configure each item. Refer to the [Mail Settings]
item in [Configuring and Controlling the Projector via a Web Browser] for
further information.
7) Click the [Apply] button to save the settings.
NOTE • Click the [Send Test Mail] button in [Mail Settings] to confirm
that the e-mail settings are correct. The following mail will be delivered to the
specified addresses.
Subject line : Test Mail
Text : Send Test Mail
<Projector name>
Date
<Testing date>
Time
<Testing time>
IP Address
<Projector IP address>
MAC Address <Projector MAC address>
83
Download from Www.Somanuals.com. All Manuals Search And Download.
Failure & Warning Alerts via E-mail
Mail Settings (Continued)
8) Configure the Failure/Warning Alerts via E-mail settings. Click [Alert Settings]
on the main menu.
9) Select and configure each alert item. Refer to [Alert Settings] in [Configuring
and Controlling the Projector via a Web Browser] for further information.
10) Click the [Apply] button to save the settings.
Failure/Warning e-mails are formatted as follows:
Subject line : <Mail title>
<Projector name>
Text
: <Mail text>
Date
<Failure/Warning date>
<Failure/Warning time>
<Projector IP address>
Time
IP Address
MAC Address <Projector MAC address>
84
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector management via SNMP
Projector management via SNMP
When SNMP is enabled, the projector is able to send Failure/Warning Alerts to a
specified PC.
NOTE • It is recommended that SNMP functions be carried out by a network
administrator.
• SNMP management software must be installed on the computer to monitor
the projector via SNMP.
SNMP settings
Configure the following items via a web browser to use SNMP.
Example: If the IP address of the projector is set to 192.168.1.10:
1) Enter [https://192.168.1.10] into the address bar of the web browser.
2) Enter the Administrator ID and Password and click [Logon].
3) Click [Port Settings] on the main menu.
4) Click the [Enable] check box to open the SNMP Port.
Set the IP address to send the SNMP Trap to when a Failure/Warning occurs.
NOTE • A Network Restart is required after the SNMP Trap configuration
settings have been changed. Click [Network Restart] and configure the
following items.
5) Click [Security Settings] on the main menu.
6) Click [SNMP] and set the Community Name on the screen that is displayed.
NOTE • A Network Restart is required after the Community Name has been
changed.
• Click [Network Restart] and configure the following items.
7) Configure the settings for Trap transmission of Failures/Warnings. Click
[Alert Settings] on the main menu and select the Failure/Warning item to be
configured.
8) Click the [Enable] check box to send out the SNMP trap for Failures/Warnings.
Clear the [Enable] check box when SNMP trap transmission is not required.
9) Click the [Apply] button to save the settings.
85
Download from Www.Somanuals.com. All Manuals Search And Download.
Controlling the Projector via Scheduling
Controlling the Projector via Scheduling
The projector can be automatically controlled via scheduling.
NOTE • You can schedule the following control events: Power ON/OFF, Input
Source and Transferred Image Display.
• There are 3 types of Scheduling, 1) daily 2) day of the week 3) specific date.
• The priority for scheduled events is as follows 1) specific date 2) day of the
week 3) daily.
• Up to five specific dates are available for scheduled events. Priority is given to
those with the lower numbers when more than one event has been scheduled
for the same date and time (e.g., ‘Specific day No. 1’ has priority over ‘Specific
day No. 2’ and so on.
• Be sure to set the date and time before enabling scheduled events.
86
Download from Www.Somanuals.com. All Manuals Search And Download.
Controlling the Projector via Scheduling
Date/Time Settings
The Date/Time setting can be adjusted via a web browser.
Example: If the IP address of the projector is set to 192.168.1.10:
1) Enter [https://192.168.1.10] into the address bar of the web browser.
Enter the Administrator ID and Password and click [Logon].
2) Click [Date/Time Settings] on the main menu and configure each item.
Refer to the [Date/Time Settings] item in [Configuring and Controlling the
Projector via a Web Browser] for further information.
3) Click the [Apply] button to save the settings.
NOTE • A Network Restart is required after the Daylight Savings Time or
SNTP configuration settings have been changed.
• The battery for the built in clock may be dead if the clock loses time even
when the DATE and TIME have been set correctly. Replace the battery by
following the instructions on replacing the battery.
(User's Manual - Operating Guide : Replacing Internal Clock battery)
• The Internal Clock’s time may not remain accurate. Using SNTP is
recommended to maintain accurate time.
87
Download from Www.Somanuals.com. All Manuals Search And Download.
Controlling the Projector via Scheduling
Schedule Settings
Schedule settings can be configured from a web browser.
Example: If the IP address of the projector is set to 192.168.1.10:
1) Enter [https://192.168.1.10] into the address bar of the web browser.
2) Enter the Administrator ID and Password and click [Logon].
3) Click [Schedule Settings] on the main menu and select the required schedule
item.
4) Click the [Enable] check box to enable scheduling.
5) Enter the Date (Month/Day) for specific date scheduling.
6) Click [Add] and set the hour, command and parameters and click [Add This
Schedule] when you want to add a command.
7) Click the [Delete] button when you want to delete a schedule.
8) Click the [Apply] button to save the settings.
There are three types of scheduling.
1) Daily: Perform the specified operation at a specified time every day.
2) Sunday ~ Saturday: Perform the specified operation at the specified time on a
specified day of the week.
3) Specific Date: Perform the specified operation on the specified date and time.
NOTE • In Standby mode the power indicator will flash green for approx. 3
seconds when at least 1 “Power ON” schedule is saved.
• When the schedule function is used, the power cord must be connected to
the projector and the outlet and the power switch must be turned on, [ | ]. The
schedule function does not work when the power switch is turned off, [] or
the breaker in a room is tripped. The power indicator will lights orange or green
when the projector gets is receiving the power.
88
Download from Www.Somanuals.com. All Manuals Search And Download.
e-Shot (Still Image Transfer) Display
e-Shot (Still Image Transfer) Display
The projector can display a still image that is transferred via the network.
Communication Port
The following port is used for e-Shot.
TCP #9716
)
NOTE • e-Shot is not available via communication ports which are used for
the command control (TCP #23 and TCP #9716).
e-Shot (Still Image Transfer) Settings
Configure the following items from a web browser when e-Shot is used.
Example: If the IP address of the projector is set to 192.168.1.10:
1) Enter [https://192.168.1.10] into the address bar of the web browser.
2) Enter the Administrator ID and Password and
click [Logon].
3) Click [Port settings] on the main menu.
4) Click the [Enable] check box to open the
[Image Transfer Port (Port: 9716)]. Click the
[Enable] check box for the [Authentication]
setting when authentication is required,
otherwise clear the check box.
5) Click the [Apply] button to save the settings.
89
Download from Www.Somanuals.com. All Manuals Search And Download.
e-Shot (Still Image Transfer) Display
e-Shot (Still Image Transfer) Settings (Continued)
When the authentication setting is enabled, the following settings are required.
6) Click [Security Settings] on the main menu.
7) Select [Network Control] and enter the desired authentication password. *
see Note1
8) Click the [Apply] button to save the settings. * see Note2
NOTE1 • The Authentication Password will be the same for [Network Control
Port1 (Port: 23)], [Network Control Port2 (Port: 9715)], and [Image Transfer
Port (Port: 9716)].
NOTE2 • The new configuration settings are activated after restarting the
network. Restart the network connection when any configuration settings are
changed. The network connection can be restarted using [Network Restart] on
the main menu.
e-Shot (Still Image Transfer) Transmission
e-Shot transmission requires an exclusive application for your PC. You can
download it from the Hitachi web site. Refer to the manual for the application for
instructions.
90
Download from Www.Somanuals.com. All Manuals Search And Download.
Command Control via the Network
Command Control via the Network
You can configure and control the projector via the network using RS-232C
commands.
Communication Port
The following two ports are assigned for the command control.
TCP #23
TCP #9715
NOTE • Command control is not available via communication port (TCP
#9716) that is used for the e-Shot transmission function.
Command Control Settings
Configure the following items from a web browser when command control is used.
Example: If the IP address of the projector is set to 192.168.1.10:
1) Enter [https://192.168.1.10] into the address bar of the web browser.
2) Enter the Administrator ID and Password and click [Logon].
3) Click [Port settings] on the main menu.
4) Click the [Enable] check box to open [Network Control Port (Port: 23)] to use
TCP #23. Click the [Enable] check box for the [Authentication] setting when
authentication is required, otherwise clear the check box.
5) Click the [Enable] check box to open [Network Control Port (Port: 9715)] to
use TCP #9715. Click the [Enable] check box for the [Authentication] setting
when authentication is required, otherwise clear the check box.
6) Click the [Apply] button to save the settings.
91
Download from Www.Somanuals.com. All Manuals Search And Download.
Command Control via the Network
Command Control Settings (Continued)
When the authentication setting is enabled, the following settings are required.
(
7) Click [Security Settings] on the main menu.
8) Click [Network Control] and enter the desired authentication password. * See
Note1.
9) Click the [Apply] button to save the settings. * See Note2.
NOTE1 • The Authentication Password will be the same for [Network Control
Port1 (Port: 23)], [Network Control Port2 (Port: 9715)], and [Image Transfer
Port (Port: 9716)].
NOTE2 • The new configuration settings are activated after restarting the
network. Restart the network when any configuration settings are changed.
The network connection can be restarted using [Network Restart] on the main
menu.
92
Download from Www.Somanuals.com. All Manuals Search And Download.
Command Control via the Network
Command format
Command formats differ among the different communication ports.
TCP #23
You can use the RS-232C commands without any changes. The reply data format
is the same as the RS-232C commands. However, the following reply will be sent
back in the event of authentication failure when authentication is enabled.
<Reply in the event of an authentication error>
Reply
Error code
0x04 0x00
0x1F
TCP #9715
Send Data format
The following formatting is added to the header (0x02), Data length (0x0D),
Checksum (1byte) and Connection ID (1 byte) of the RS-232C commands.
Data
length
Connection
Header
RS-232Ccommand
Checksum
ID
0x02
0x0D
13 bytes
1 byte
1 byte
Header
Data length
RS-232C commands → RS-232C commands that start with 0xBE 0xEF (13 bytes)
→ 0x02, Fixed
→ RS-232C commands byte length (0x0D, Fixed)
Check Sum
→ This is the value to make zero on the addition of the lower
8 bits from the header to the checksum.
→ Random value from 0 to 255 (This value is attached to
the reply data)
Connection ID
93
Download from Www.Somanuals.com. All Manuals Search And Download.
Command Control via the Network
Reply Data format
The connection ID (the data is same as the connection ID data on the sending
data format) is attached to the RS-232C commands reply data.
<ACK reply>
Connection
Reply
ID
0x06
1 byte
<NAK reply>
Connection
ID
Reply
0x15
1 byte
<Error reply>
Connection
ID
Reply
0x1C
Error code
2 bytes
1 byte
<Data reply>
Connection
ID
Reply
Data
0x1D
2 bytes
1 byte
<Projector busy reply>
Connection
ID
Reply
Status code
2 bytes
0x1F
1 byte
<Authentication error reply>
Authentication
Reply
Connection
ID
Error code
0x1F
0x04
0x00
1 byte
94
Download from Www.Somanuals.com. All Manuals Search And Download.
Command Control via the Network
Automatic Connection Break
The TCP connection will be automatically disconnected after there is no
communication for 30 seconds after being established.
Authentication
The projector does not accept commands without authentication success
when authentication is enabled. The projector uses a challenge response type
authentication with an MD5 (Message Digest 5) algorithm.
When the projector is using a LAN, a random eight bytes will be returned if
authentication is enabled. Bind this received 8 bytes and the authentication
password and digest this data with the MD5 algorithm and add this in front of the
commands to send.
Following is a sample if the authentication password is set to “password” and the
random eight bytes are “a572f60c”.
1) Select the projector.
2) Receive the random eight bytes “a572f60c” from the projector.
3) Bind the random eight bytes “a572f60c” and the authentication password
“password” and it becomes “a572f60cpassword”.
4) Digest this bind “a572f60cpassword” with MD5 algorithm.
It will be “e3d97429adffa11bce1f7275813d4bde”.
5) Add this “e3d97429adffa11bce1f7275813d4bde” in front of the commands and
send the data.
Send “e3d97429adffa11bce1f7275813d4bde”+command.
6) When the sending data is correct, the command will be performed and the
reply data will be returned. Otherwise, an authentication error will be returned.
95
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes:
96
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector
, 8755D-RJ, & 8065
8755D
User's Manual – Operating Guide
Technical
Example of computer signal
Resolution (H x V) H. frequency (kHz) V. frequency (Hz)
Rating
Signal mode
720 x 400
640 x 480
640 x 480
640 x 480
640 x 480
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
832 x 624
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1152 x 864
1280 x 960
1280 x 1024
1280 x 1024
1280 x 1024
1600 x 1200
37.9
31.5
37.9
37.5
43.3
35.2
37.9
48.1
46.9
53.7
49.7
48.4
56.5
60.0
68.7
67.5
60.0
64.0
80.0
91.1
75.0
85.0
59.9
72.8
75.0
85.0
56.3
60.3
72.2
75.0
85.1
74.5
60.0
70.1
75.0
85.0
75.0
60.0
60.0
75.0
85.0
60.0
VESA
VESA
VESA
VESA
VESA
VESA
VESA
VESA
VESA
VESA
TEXT
VGA (60Hz)
VGA (72Hz)
VGA (75Hz)
VGA (85Hz)
SVGA (56Hz)
SVGA (60Hz)
SVGA (72Hz)
SVGA (75Hz)
SVGA (85Hz)
Mac 16” mode
XGA (60Hz)
XGA (70Hz)
XGA (75Hz)
XGA (85Hz)
SXGA (75Hz)
SXGA (60Hz)
SXGA (60Hz)
SXGA (75Hz)
SXGA (85Hz)
UXGA (60Hz)
VESA
VESA
VESA
VESA
VESA
VESA
VESA
VESA
VESA
VESA
NOTE • Be sure to check jack type, signal level, timing and resolution
before connecting this projector to a computer.
• Some computers may have multiple display screen modes. Use of some of
these modes will not be possible with this projector.
• Depending on the input signal, full-size display may not be possible in some
cases. Refer to the number of display pixels above.
• Although the projector can display signals with resolution up to UXGA
(1600x1200), the signal will be converted to the projector’s panel resolution
before being displayed. The best display performance will be achieved if the
resolutions of the input signal and projector panel are identical.
• Automatically adjustment may not function correctly with some input signals.
• The image may not be displayed correctly when the input sync signal is a
composite sync or a sync on G.
97
Download from Www.Somanuals.com. All Manuals Search And Download.
Example of computer signal
Initial set signals
The following signals are used for the initial settings. The signal timing of some
computer models may be different. In such case, adjust the items V POSITION
and H POSITION in the IMAGE menu.
Back porch (B)
Front porch (D)
Back porch (b)
Front porch (d)
Display interval (C)
Display interval (c)
Data
Data
V. Sync.
H. Sync.
Sync (A)
Sync (a)
Horizontal signal timing (μs)
Vertical signal timing (lines)
Computer/
Computer/
Signal
Signal
(A)
2.0
3.8
1.3
2.0
1.6
(B)
(C)
(D)
(a)
3
2
3
3
3
2
4
6
3
3
3
6
6
3
3
(b)
42
33
28
16
25
22
23
23
21
27
39
29
29
28
36
(c)
(d)
1
10
9
1
1
1
1
37
1
1
TEXT
3.0 20.3 1.0
1.9 25.4 0.6
4.1 20.3 0.8
3.8 20.3 0.5
2.2 17.8 1.6
3.6 22.2 0.7
2.2 20.0 1.0
1.3 16.0 1.1
3.2 16.2 0.3
2.7 14.2 0.6
3.9 14.5 0.6
2.5 15.8 0.4
1.9 13.7 0.3
2.2 13.0 0.2
2.2 10.8 0.5
TEXT
400
480
480
480
480
600
600
600
600
600
624
768
768
768
768
VGA (60Hz)
VGA (72Hz)
VGA (75Hz)
VGA (85Hz)
VGA (60Hz)
VGA (72Hz)
VGA (75Hz)
VGA (85Hz)
SVGA (56Hz)
SVGA (60Hz)
SVGA (72Hz)
SVGA (75Hz)
SVGA (85Hz)
Mac 16" mode
XGA (60Hz)
XGA (70Hz)
XGA (75Hz)
XGA (85Hz)
SVGA (56Hz) 2.0
SVGA (60Hz) 3.2
SVGA (72Hz) 2.4
SVGA (75Hz) 1.6
SVGA (85Hz) 1.1
Mac 16" mode 1.1
1
3
3
1
XGA (60Hz)
XGA (70Hz)
XGA (75Hz)
XGA (85Hz)
2.1
1.8
1.2
1.0
1
1152 x 864
(75Hz)
1280 x 960
(60Hz)
1280 x 1024
(60Hz)
1280 x 1024
(75Hz)
1280 x 1024
(85Hz)
1600 x 1200
(60Hz)
1152 x 864
(75Hz)
1280 x 960
(60Hz)
1280 x 1024
(60Hz)
1280 x 1024
(75Hz)
1280 x 1024
(85Hz)
1600 x 1200
(60Hz)
1.2
1.0
1.0
1.1
1.0
1.2
2.4 10.7 0.6
3
3
3
3
3
3
32
36
864
960
1
1
1
1
1
1
2.9
2.3
1.8
1.4
1.9
11.9
11.9
9.5
0.9
0.4
0.1
0.4
0.4
38 1024
38 1024
44 1024
46 1200
8.1
9.9
98
Download from Www.Somanuals.com. All Manuals Search And Download.
Connection to the ports
Connection to the ports
RGB IN OUT switch
When this switch is not pushed
in, RGB IN2 is selected.
A
B
AUDIO IN2
R
Y
When this switch is pushed in,
RGB OUT is selected.
CONTROL
RGB IN1
RGB IN2
RGB OUT
USB
AUDIO OUT
CB/PB
CR/PR
L
K
AUDIO IN1
VIDEO
S-VIDEO
Note: 8755D-RJ has a LAN port RJ-45.
A
B
RGB IN1, RGB IN2, RGB OUT
5
4
3
2
1
D-sub 15pin mini shrink jack
10
9
8
7
6
15 14 13 12 11
• Video signal: RGB separate, Analog, 0.7Vp-p,
75Ω terminated (positive)
• H/V. sync. Signal: TTL level (positive/negative)
• Composite sync. Signal: TTL level
At RGB signal
At component video signal
Pin
1
Signal
Pin
1
Signal
CR/PR
Video Red
2
3
Video Green
Video Blue
2
3
Y
CB/PB
4
5
(No connection)
Ground
4
5
(No connection)
Ground
6
7
8
9
Ground Red
Ground Green
Ground Blue
(No connection)
6
7
8
9
10
11
CR/PR Ground
Y Ground
CB/PB Ground
(No connection)
Ground
10 Ground
11 (No connection)
A
12
B
(No connection)
: SDA (DDC data),
15
13 H. sync / Composite sync.
14 V. sync.
B
Except when set to RGB
OUT
*
A
15
B
: SCL (DDC clock),
99
Download from Www.Somanuals.com. All Manuals Search And Download.
Connection to the ports
AUDIO IN2
R
Y
C
D
CONTROL
RGB IN1
RGB IN2
RGB OUT
USB
AUDIO OUT
C
B
R
/
P
B
R
L
K
AUDIO IN1
E C
/P
G
F
VIDEO
S-VIDEO
C
D
E
COMPONENT VIDEO Y,
C
B/PB
,
C
R/PR
RCA jack x3
• System: 525i(480i), 525p(480p), 625i(576i), 750p(720p), 1125i(1080i)
Port
Y
Signal
Component video Y, 1.0±0.1Vp-p, 75Ω terminator with composite
B
C
B/P Component video CB/PB, 0.7±0.1Vp-p, 75Ω terminator
R
R
C /P Component video CR/PR, 0.7±0.1Vp-p, 75Ω terminator
F
S-VIDEO
1
2
Mini DIN 4pin jack
3
4
Pin
Signal
Color signal 0.286Vp-p (NTSC, burst), 75Ω terminator
Color signal 0.300Vp-p (PAL/SECAM, burst) 75Ω terminator
Brightness signal, 1.0Vp-p, 75Ω terminator
Ground
Ground
1
2
3
4
G
VIDEO
RCA jack
• System: NTSC, PAL, SECAM, PAL-M, PAL-N, NTSC4.43, PAL60
• 1.0±0.1Vp-p, 75Ω terminator
100
Download from Www.Somanuals.com. All Manuals Search And Download.
Connection to the ports
L
K
M
AUDIO IN2
R
Y
I
CONTROL
H
RGB IN1
RGB IN2
RGB OUT
USB
J
AUDIO OUT
CB/PB
CR/PR
L
K
AUDIO IN1
N
VIDEO
LINK
ACT
LAN
S-VIDEO
H
I J
Ø3.5 stereo mini jack),
AUDIO 1-IN (
AUDIO 2 L/R (RCA jack)
• 200mVrms(max.) 35kΩ termination
K
Ø3.5 stereo mini jack)
AUDIO OUT (
• 200mVrms(max.) 1kΩ output impedance
Pin
Signal
L
USB
4
1
3
2
1
2
3
4
+5V
USB B type jack
- Data
+ Data
Ground
M
CONTROL
D-sub 9pin plug
9
8
7
6
5
4
3
2
1
• About the details of RS-232C communication, please refer to the following page.
Pin
1
Signal
(No connection)
Pin
4
Signal
(No connection)
Ground
Pin
7
Signal
RTS
CTS
2
3
RD
TD
5
6
8
9
(No connection)
(No connection)
LAN Port
RJ-45 Jack, Model 8755D-RJ Only!
N
Used for Ethernet input/output.
This port is used when utilizing network functions.
101
Download from Www.Somanuals.com. All Manuals Search And Download.
RS-232C Communication
RS-232C Communication
1
2
3
4
5
1
2
3
4
5
6
6
8
8
7
9
7
9
CONTROL port
of the projector
RS-232C cable (Cross)
RS-232C port
of the computer
- (1)
RD (2)
TD (3)
- (4)
(1) CD
(2) RD
(3) TD
(4) DTR
(5) GND
(6) DSR
(7) RTS
(8) DTS
(9) RI
GND (5)
- (6)
RTS (7)
CTS (8)
- (9)
Connecting the cable
1. Turn off the projector and the computer.
Connect the CONTROL port of the projector with a RS-232C port of
the computer by a RS-232C cable (cross). Use the cable that fulfills the
specification shown in the previous page.
2.
Turn the computer on, and after the computer has started up turn the
projector on.
3.
Communications setting
19200bps, 8N1
1. Protocol
Consist of header (7 bytes) + command data (6 bytes).
2. Header
BE + EF + 03 + 06 + 00 + CRC_low + CRC_high
CRC_low : Lower byte of CRC flag for command data
CRC_high : Upper byte of CRC flag for command data
3. Command data
Command data chart
byte_0
byte_1
byte_2
byte_3
high
byte_4
Setting code
low
byte_5
high
Action
Type
low
high
low
Action (byte_0 - 1)
Action
Classification
Content
1
2
SET
GET
Change setting to desired value.
Read projector internal setup value.
4
5
INCREMENT Increment setup value by 1.
DECREMENT Decrement setup value by 1.
6
EXECUTE
Run a command.
102
Download from Www.Somanuals.com. All Manuals Search And Download.
RS-232C Communication (continued)
Requesting projector status (Get command)
(1) Send the request code Header + Command data (‘02H’+‘00H’+ type (2 bytes)+
‘00H’ +‘00H’) from the computer to the projector.
(2) The projector returns the response code ‘1DH’+ data (2 bytes) to the computer.
Changing the projector settings (Set command)
(1) Send the setting code Header + Command data (‘01H’+‘00H’+ type (2 bytes) +
setting code (2 bytes)) from the computer to the projector.
(2) The projector changes the setting based on the above setting code.
(3) The projector returns the response code ‘06H’ to the computer.
Using the projector default settings (Reset Command)
(1) The computer sends the default setting code Header + Command data (‘06H’+
‘00H’ + type (2 bytes) +‘00H’+‘00H’) to the projector.
(2) The projector changes the specified setting to the default value.
(3) The projector returns the response code ‘06H’ to the computer.
Increasing the projector setting value (Increment command)
(1) The computer sends the increment code Header + Command data (‘04H’+
‘00H’+ type (2 bytes) +‘00H’+‘00H’) to the projector.
(2) The projector in creases the setting value on the above setting code.
(3) The projector returns the response code ‘06H’ to the computer.
Decreasing the projector setting value (Decrement command)
(1) The computer sends the decrement code Header + Command data (‘05H’+
‘00H’+ type (2 bytes) +‘00H’ + ‘00H’) to the projector.
(2) The projector decreases the setting value on the above setting code.
(3) The projector returns the response code ‘06H’ to the computer.
When the projector cannot understand the received command
When the projector cannot understand the received command, the error code ‘15H’
is sent back to the computer.
Sometimes the projector cannot properly receive the command. In such a
case, the command is not executed and the error code ‘15H’ is sent back to the
computer. If this error code is returned, send the same command again.
When the projector cannot execute the received command.
When the projector cannot execute the received command, the error code ‘1cH’
+ ‘xxxxH’ is sent back to the computer. When the data length is greater than
indicated by the data length code, the projector ignore the excess data code.
Conversely when the data length is shorter than indicated by the data length
code, an error code will be returned to the computer.
NOTE • Operation cannot be guaranteed when the projector receives an undefined
command or data.
• Provide an interval of at least 40ms between the response code and any other code.
• The projector outputs test data when the power supply is switched ON, and when the
lamp is lit. Ignore this data.
• Commands are not accepted during warm-up.
103
Download from Www.Somanuals.com. All Manuals Search And Download.
RS-232C Communication (continued)
Command Data
Names
Power
Operation Type
Header
CRC
Action
Type
Setting Code
Set
Turn off
Turn on
Get
BE EF
BE EF
BE EF
03
03
03
06 00
06 00
06 00
2A D3
BA D2
19 D3
01 00
01 00
02 00
00 60
00 60
00 60
00 00
01 00
00 00
(Example return)
00 00
01 00
(On)
06 00
02 00
(Cool down)
(Off)
RGB2 Status
Input Source
Get
BE EF
00 00
(RGB IN2)
BE EF
03
F1 D8
02 00
21 20
00 00
01 00
(RGB OUT)
06 00
Set
RGB IN 1
RGB IN 2
VIDEO
03
03
03
03
03
03
03
FE D2
3E D0
6E D3
9E D3
AE D1
CD D2
D9 D8
01 00
01 00
01 00
01 00
01 00
02 00
02 00
00 20
00 20
00 20
00 20
00 20
00 20
20 60
00 00
04 00
01 00
02 00
05 00
00 00
00 00
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
06 00
06 00
06 00
06 00
06 00
06 00
S-VIDEO
COMPONENT
Get
Error Status
Get
(Example return)
00 00
01 00
(Cover error)
05 00
02 00
(Fan error)
06 00
03 00
(Lamp error)
07 00
(Normal)
04 00
(Temp error)
08 00
(Air flow error)
09 00
(Lamp time error)
10 00
(Cool error)
(Filter error) (Filter missing error)(Inner Sencer error)
BRIGHTNESS
Get
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
03
03
03
03
03
03
03
03
03
03
03
03
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
89 D2
EF D2
3E D3
58 D3
FD D3
9B D3
4A D2
A4 D2
23 F6
B3 F7
E3 F4
10 F6
02 00
04 00
05 00
06 00
02 00
04 00
05 00
06 00
01 00
01 00
01 00
02 00
03 20
00 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00
01 00
04 00
00 00
Increment
Decrement
Execute
Get
03 20
03 20
00 70
04 20
04 20
04 20
01 70
BA 30
BA 30
BA 30
BA 30
BRIGHTNESS Reset
CONTRAST
Increment
Decrement
Execute
NORMAL
CINEMA
DYNAMIC
Get
CONTRAST Reset
MODE
Set
Set
(Example return)
00 00
01 00
04 00
10 00
(Normal)
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
(Cinema) (Dynamic) (Custom)
GAMMA
#1 DEFAULT
#1 CUSTOM
#2 DEFAULT
#2 CUSTOM
#3 DEFAULT
#3 CUSTOM
Get
03
03
03
03
03
03
03
06 00
06 00
06 00
06 00
06 00
06 00
06 00
07 E9
07 FD
97 E8
97 FC
67 E8
67 FC
F4 F0
01 00
01 00
01 00
01 00
01 00
01 00
02 00
A1 30
A1 30
A1 30
A1 30
A1 30
A1 30
A1 30
20 00
10 00
21 00
11 00
22 00
12 00
00 00
104
Download from Www.Somanuals.com. All Manuals Search And Download.
RS-232C Communication (continued)
Command Data
Names
Operation Type
Header
CRC
Action
Type
Setting Code
User Gamma Pattern Set
Off
9 step gray scale
15 steps gray scale
Ramp
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
FB FA
6B FB
9B FB
0B FA
C8 FA
08 FE
6E FE
BF FF
F4 FF
92 FF
43 FE
B0 FF
D6 FF
07 FE
4C FE
2A FE
FB FF
38 FF
5E FF
8F FE
C4 FE
A2 FE
73 FF
80 FE
E6 FE
37 FF
7C FF
1A FF
CB FE
01 00
01 00
01 00
01 00
02 00
02 00
04 00
05 00
02 00
04 00
05 00
02 00
04 00
05 00
02 00
04 00
05 00
02 00
04 00
05 00
02 00
04 00
05 00
02 00
04 00
05 00
02 00
04 00
05 00
80 30
80 30
80 30
80 30
80 30
90 30
90 30
90 30
91 30
91 30
91 30
92 30
92 30
92 30
93 30
93 30
93 30
94 30
94 30
94 30
95 30
95 30
95 30
96 30
96 30
96 30
97 30
97 30
97 30
00 00
01 00
02 00
03 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00
Get
User Gamma Point 1
User Gamma Point 2
User Gamma Point 3
User Gamma Point 4
User Gamma Point 5
User Gamma Point 6
User Gamma Point 7
User Gamma Point 8
Get
Increment
Decrement
Get
Increment
Decrement
Get
Increment
Decrement
Get
Increment
Decrement
Get
Increment
Decrement
Get
Increment
Decrement
Get
Increment
Decrement
Get
Increment
Decrement
COLOR TEMP
Set
LOW
MIDDLE
HIGH
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
03
03
03
03
03
03
03
03
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
6B F4
9B F4
0B F5
3B F8
C8 F5
34 F4
52 F4
83 F5
01 00
01 00
01 00
01 00
02 00
02 00
04 00
05 00
B0 30
B0 30
B0 30
B0 30
B0 30
B1 30
B1 30
B1 30
01 00
02 00
03 00
10 00
00 00
00 00
00 00
00 00
CUSTOM
Get
COLOR TEMP GAIN R
Get
Increment
Decrement
105
Download from Www.Somanuals.com. All Manuals Search And Download.
RS-232C Communication (continued)
Command Data
Names
Operation Type
Header
CRC
Action
Type
Setting Code
COLOR TEMP GAIN G
Get
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
70 F4
16 F4
C7 F5
8C F5
EA F5
3B F4
04 F5
62 F5
B3 F4
40 F5
26 F5
F7 F4
BC F4
DA F4
0B F5
02 00
04 00
05 00
02 00
04 00
05 00
02 00
04 00
05 00
02 00
04 00
05 00
02 00
04 00
05 00
B2 30
B2 30
B2 30
B3 30
B3 30
B3 30
B5 30
B5 30
B5 30
B6 30
B6 30
B6 30
B7 30
B7 30
B7 30
00 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00
Increment
Decrement
Get
COLOR TEMP GAIN B
Increment
Decrement
Get
COLOR TEMP
OFFSET R
Increment
Decrement
Get
COLOR TEMP
OFFSET G
Increment
Decrement
Get
COLOR TEMP
OFFSET B
Increment
Decrement
COLOR
Get
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
B5 72
D3 72
02 73
80 D0
49 73
2F 73
FE 72
7C D1
F1 72
97 72
46 73
C4 D0
4A 72
DA 73
2A 73
79 72
0E D7
9E D6
6E D6
FE D7
F2 D6
62 D7
92 D7
02 D6
02 00
04 00
05 00
06 00
02 00
04 00
05 00
06 00
02 00
04 00
05 00
06 00
01 00
01 00
01 00
02 00
01 00
01 00
01 00
01 00
01 00
01 00
01 00
01 00
02 22
02 22
02 22
0A 70
03 22
03 22
03 22
0B 70
01 22
01 22
01 22
09 70
07 22
07 22
07 22
07 22
14 20
14 20
14 20
14 20
15 20
15 20
15 20
15 20
00 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00
01 00
02 00
00 00
00 00
01 00
02 00
03 00
00 00
01 00
02 00
03 00
Increment
Decrement
COLOR Reset
TINT
Execute
Get
Increment
Decrement
TINT Reset
Execute
SHARPNESS
Get
Increment
Decrement
SHARPNESS Reset
PROGRESSIVE
Execute
Set
TURN OFF
TV
FILM
Get
1
MY MEMORY Load Set
MY MEMORY Save Set
2
3
4
1
2
3
4
106
Download from Www.Somanuals.com. All Manuals Search And Download.
RS-232C Communication (continued)
Command Data
Names
Operation Type
Header
CRC
Action
Type
Setting Code
ASPECT
Set
4:3
16:9
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
9E D0
0E D1
FE D1
5E DD
AD D0
91 70
F7 70
26 71
EC D9
0D 83
6B 83
BA 82
E0 D2
F1 82
97 82
46 83
1C D3
49 83
2F 83
FE 82
B5 82
D3 82
02 83
68 D2
91 D0
0E 72
01 00
01 00
01 00
01 00
02 00
02 00
04 00
05 00
06 00
02 00
04 00
05 00
06 00
02 00
04 00
05 00
06 00
02 00
04 00
05 00
02 00
04 00
05 00
06 00
06 00
01 00
01 00
01 00
01 00
01 00
02 00
01 00
01 00
02 00
01 00
01 00
01 00
01 00
01 00
01 00
01 00
02 00
01 00
01 00
02 00
08 20
08 20
08 20
08 20
08 20
09 22
09 22
09 22
27 70
00 21
00 21
00 21
02 70
01 21
01 21
01 21
03 70
03 21
03 21
03 21
02 21
02 21
02 21
04 70
0A 20
04 22
04 22
04 22
04 22
04 22
04 22
17 20
17 20
17 20
00 22
00 22
00 22
00 22
00 22
00 22
00 22
00 22
14 30
14 30
14 30
00 00
01 00
02 00
10 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00
01 00
02 00
03 00
04 00
00 00
00 00
01 00
00 00
0A 00
04 00
05 00
09 00
02 00
08 00
07 00
00 00
00 00
01 00
00 00
SMALL
NORMAL
Get
OVER SCAN
Get
Increment
Decrement
Execute
Get
OVER SCAN Reset
V POSITION
Increment
Decrement
Execute
Get
V POSITION Reset
H POSITION
Increment
Decrement
Execute
Get
H POSITION Reset
H PHASE
Increment
Decrement
Get
H SIZE
Increment
Decrement
Execute
Execute
AUTO
H SIZE Reset
AUTO ADJUST
COLOR SPACE
Set
RGB
9E 73
6E 73
FE 72
CE 70
3D 72
4A D7
DA D6
79 D7
9E 75
FE 71
6E 70
6E 75
5E 72
FE 74
0E 71
0D 73
CB D6
5B D7
F8 D6
SMPTE240
REC709
REC601
Get
COMPONENT
Set
Set
COMPONENT
SCART RGB
Get
VIDEO FORMAT
AUTO
NTSC
PAL
SECAM
NTSC4.43
M-PAL
N-PAL
Get
FRAME LOCK
Set
TURN OFF
TURN ON
Get
107
Download from Www.Somanuals.com. All Manuals Search And Download.
RS-232C Communication (continued)
Command Data
Names
Operation Type
Header
CRC
Action
Type
Setting Code
KEYSTONE V
Get
Increment
Decrement
Execute
NORMAL
WHISPER
Get
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
B9 D3
DF D3
0E D2
08 D0
3B 23
AB 22
08 23
C7 D2
57 D3
A7 D3
37 D2
F4 D2
31 D3
57 D3
86 D2
FE DD
6E DC
9E DC
CD DD
CE DC
5E DD
AE DD
FD DC
02 DC
92 DD
62 DD
31 DC
46 DC
D6 DD
26 DD
75 DC
32 DD
A2 DC
52 DC
01 DD
02 00
04 00
05 00
06 00
01 00
01 00
02 00
01 00
01 00
01 00
01 00
02 00
02 00
04 00
05 00
01 00
01 00
01 00
02 00
01 00
01 00
01 00
02 00
01 00
01 00
01 00
02 00
01 00
01 00
01 00
02 00
01 00
01 00
01 00
02 00
07 20
07 20
07 20
0C 70
00 33
00 33
00 33
01 30
01 30
01 30
01 30
01 30
01 20
01 20
01 20
30 20
30 20
30 20
30 20
34 20
34 20
34 20
34 20
31 20
31 20
31 20
31 20
32 20
32 20
32 20
32 20
35 20
35 20
35 20
35 20
00 00
00 00
00 00
00 00
00 00
01 00
00 00
00 00
01 00
02 00
03 00
00 00
00 00
00 00
00 00
00 00
01 00
02 00
00 00
00 00
01 00
02 00
00 00
00 00
01 00
02 00
00 00
00 00
01 00
02 00
00 00
00 00
01 00
02 00
00 00
KEYSTONE V Reset
WHISPER
Set
Set
MIRROR
NORMAL
H:INVERT
V:INVERT
H&V:INVERT
Get
VOLUME
Get
Increment
Decrement
TURN OFF
Audio1
AUDIO - RGB1
Set
Set
Set
Set
Audio2
Get
AUDIO - RGB2
AUDIO - Video
AUDIO - S-Video
TURN OFF
Audio1
Audio2
Get
TURN OFF
Audio1
Audio2
Get
TURN OFF
Audio1
Audio2
Get
AUDIO - Component Set
TURN OFF
Audio1
Audio2
Get
108
Download from Www.Somanuals.com. All Manuals Search And Download.
RS-232C Communication (continued)
Command Data
Names
MUTE
Operation Type
Header
CRC
Action
Type
Setting Code
Set
Set
TURN OFF
TURN ON
Get
BE EF
BE EF
BE EF
03
03
03
06 00
06 00
06 00
46 D3
D6 D2
75 D3
01 00
01 00
02 00
02 20
02 20
02 20
00 00
01 00
00 00
LANGUAGE
ENGLISH
FRANÇAIS
DEUTSCH
ESPAÑOL
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
F7 D3
67 D2
97 D2
07 D3
37 D1
A7 D0
57 D0
C7 D1
37 D4
A7 D5
37 DE
57 D5
C7 D4
F7 D6
67 D7
97 D7
07 D6
C4 D3
04 D7
62 D7
B3 D6
DC C6
01 00
01 00
01 00
01 00
01 00
01 00
01 00
01 00
01 00
01 00
01 00
01 00
01 00
01 00
01 00
01 00
01 00
02 00
02 00
04 00
05 00
06 00
05 30
05 30
05 30
05 30
05 30
05 30
05 30
05 30
05 30
05 30
05 30
05 30
05 30
05 30
05 30
05 30
05 30
05 30
15 30
15 30
15 30
43 70
00 00
01 00
02 00
03 00
04 00
05 00
06 00
07 00
08 00
09 00
10 00
0A 00
0B 00
0C 00
0D 00
0E 00
0F 00
00 00
00 00
00 00
00 00
00 00
ITALIANO
NORSK
NEDERLANDS
PORTUGUÊS
SVENSKA
PУCCKИЙ
SUOMI
POLSKI
TÜRKÇE
Get
MENU POSITION H
Get
Increment
Decrement
Execute
MENU POSITION H
Reset
MENU POSITION V
Get
BE EF
BE EF
BE EF
BE EF
03
03
03
03
06 00
06 00
06 00
06 00
40 D7
26 D7
F7 D6
A8 C7
02 00
04 00
05 00
06 00
16 30
16 30
16 30
44 70
00 00
00 00
00 00
00 00
Increment
Decrement
Execute
MENU POSITION V
Reset
109
Download from Www.Somanuals.com. All Manuals Search And Download.
RS-232C Communication (continued)
Command Data
Names
Operation Type
Header
CRC
Action
Type
Setting Code
OSD BRIGHT.
Get
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
A8 D5
CE D5
1F D4
FB CA
FB E2
CB D3
6B D0
9B D0
08 D3
FB D8
6B D9
C8 D8
CB CB
0B D2
9B D3
38 D2
3B EF
AB EE
08 EF
8F D6
1F D7
BC D6
02 00
04 00
05 00
01 00
01 00
01 00
01 00
01 00
02 00
01 00
01 00
02 00
01 00
01 00
01 00
02 00
01 00
01 00
02 00
01 00
01 00
02 00
18 30
18 30
18 30
00 30
00 30
00 30
00 30
00 30
00 30
20 30
20 30
20 30
04 30
04 30
04 30
04 30
C0 30
C0 30
C0 30
17 30
17 30
17 30
00 00
00 00
00 00
20 00
40 00
03 00
05 00
06 00
00 00
00 00
01 00
00 00
20 00
00 00
01 00
00 00
00 00
01 00
00 00
00 00
01 00
00 00
Increment
Decrement
My Screen
ORIGINAL
BLUE
BLANK
Set
WHITE
BLACK
Get
BLANK On/Off
START UP
Set
Set
TURN OFF
TURN ON
Get
My Screen
ORIGINAL
TURN OFF
Get
My Screen LOCK
Message
Set
Set
TURN OFF
TURN ON
Get
TURN OFF
TURN ON
Get
AUTO SEARCH
Set
TURN OFF
TURN ON
Get
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
BE EF
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
06 00
B6 D6
26 D7
85 D6
08 86
6E 86
BF 87
C2 FF
58 DC
C2 F0
98 C6
7C D2
1A D2
CB D3
83 D2
13 D3
B0 D2
01 00
01 00
02 00
02 00
04 00
05 00
02 00
06 00
02 00
06 00
02 00
04 00
05 00
01 00
01 00
02 00
16 20
16 20
16 20
10 31
10 31
10 31
90 10
30 70
A0 10
40 70
07 30
07 30
07 30
02 30
02 30
02 30
00 00
01 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00
00 00
01 00
00 00
AUTO POWER OFF
Get
Increment
Decrement
Get
LAMP TIME
LAMP TIME Reset
FILTER TIME
Execute
Get
FILER TIME Reset
MAGNIFY
Execute
Get
Increment
Decrement
NORMAL
FREEZE
Get
FREEZE
Set
110
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Audio Visual Products
2900 Dukane Drive
St. Charles, Illinois 60174
www.dukcorp.com/av
Toll-free: 800-676-2487
Fax: 630-584-5156
e-mail: [email protected]
#401-8755D-01
Download from Www.Somanuals.com. All Manuals Search And Download.
|