Portable LCD Projector
Model 8777
USER’S MANUAL
401-8777-00
Download from Www.Somanuals.com. All Manuals Search And Download.
• IBM is a trademark or registered trademark of International Business Machines Corporation.
• Macintosh, Mac OS X and PowerBook are trademarks of Apple Computer, Inc., registered in the U.S. and other
countries.
• Windows, Windows 98, Windows Me, Windows XP or Windows 2000 are trademarks or registered trademarks of
Microsoft Corporation.
• Other product and company names mentioned in this user's manual may be the trademarks or registered trade-
marks of their respective holders.
NOTES
(1) The contents of this user’s manual may not be reprinted in part or whole without permission.
(2) The contents of this user’s manual are subject to change without notice.
(3) Great care has been taken in the preparation of this user’s manual; however, should you notice any questionable
points, errors or omissions, please contact us.
(4) Notwithstanding article (3), Dukane will not be responsible for any claims on loss of profit or other matters deemed
to result from using the Projector.
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Information
Safety Cautions
Precautions
Please read this manual carefully before using your projector and keep the manual handy for future reference.
Your serial number is located on the bottom of your projector. Record it here:
CAUTION
To turn off main power, be sure to remove the plug from power outlet.
The power outlet socket should be installed as near to the equipment as possible, and should be easily
accessible.
CAUTION
TO PREVENT SHOCK, DO NOT OPEN THE CABINET.
THERE ARE HIGH-VOLTAGE COMPONENTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol warns the user that uninsulated voltage within the unit may be sufficient to cause electrical
shock. Therefore, it is dangerous to make any kind of contact with any part inside of the unit.
This symbol alerts the user that important information concerning the operation and maintenance of this
unit has been provided.
The information should be read carefully to avoid problems.
WARNING: TO PREVENT FIRE OR SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
DO NOT USE THIS UNIT’S PLUG WITHAN EXTENSION CORD OR INAN OUTLET UNLESSALLTHE PRONGS
CAN BE FULLY INSERTED.
DOC Compliance Notice (for Canada only)
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
Machine Noise Information Regulation - 3. GPSGV,
The highest sound pressure level is less than 70 dB (A) in accordance with EN ISO 7779.
CAUTION
Avoid displaying stationary images for a prolonged period of time.
Doing so can result in these images being temporarily sustained on the surface of the LCD panel.
If this should happen, continue to use your projector. The static background from previous images will
disappear.
Disposing of your used product
EU-wide legislation as implemented in each Member State requires that used electrical and electronic
products carrying the mark (left) must be disposed of separately from normal household waste. This
includes projectors and their electrical accessories or lamps. When you dispose of such products, please
follow the guidance of your local authority and/or ask the shop where you purchased the product.
After collecting the used products, they are reused and recycled in a proper way. This effort will help us
reduce the wastes as well as the negative impact such as mercury contained in a lamp to the human
health and the environment at the minimum level.
The mark on the electrical and electronic products only applies to the current European Union Member
States.
i
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Information
WARNING TO CALIFORNIA RESIDENTS:
Handling the cables supplied with this product will expose you to lead, a chemical known to the State of California
to cause birth defects or other reproductive harm. WASH HANDS AFTER HANDLING.
RF Interference (for USA only)
WARNING
The Federal Communications Commission does not allow any modifications or changes to the unit EXCEPT those
specified by Dukane Corporation in this manual. Failure to comply with this government regulation could
void your right to operate this equipment. This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses, and can radi-
ate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio / TV technician for help.
For UK only: In UK, a BS approved power cable with moulded plug has a Black (five Amps) fuse installed for use with
this equipment. If a power cable is not supplied with this equipment please contact your supplier.
Important Safeguards
These safety instructions are to ensure the long life of your projector and to prevent fire and shock. Please read them
carefully and heed all warnings.
Installation
• Do not place the projector in the following conditions:
- on an unstable cart, stand, or table.
- near water, baths, or damp rooms.
- in direct sunlight, near heaters, or heat radiating appliances.
- in a dusty, smoky or steamy environment.
- on a sheet of paper or cloth, rugs or carpets.
• If you wish to have the projector installed on the ceiling:
- Do not attempt to install the projector yourself.
- The projector must be installed by qualified technicians in order to ensure proper operation and reduce the
risk of bodily injury.
- In addition, the ceiling must be strong enough to support the projector and the installation must be in accor-
dance with any local building codes.
- Please consult your dealer for more information.
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Information
Place the projector in a horizontal position
The tilt angle of the projector should not exceed 10 degrees, nor should the projector be installed in any way other
than the desktop and ceiling mount, otherwise lamp life could decrease dramatically.
10°�
Fire and Shock Precautions
• Ensure that there is sufficient ventilation and that vents are unobstructed to prevent the build-up of heat inside your
projector. Allow at least 4 inches (10cm) of space between your projector and a wall.
• Do not try to touch the ventilation outlet on the left front (when seen from the front) as it can become heated while
the projector is turned on and immediately after the projector is turned off.
• Prevent foreign objects such as paper clips and bits of paper from falling into your projector. Do not attempt to
retrieve any objects that might fall into your projector. Do not insert any metal objects such as a wire or screwdriver
into your projector. If something should fall into your projector, disconnect it immediately and have the object removed
by a qualified service personnel.
• Do not place any objects on top of the projector.
• Do not touch the power plug during a thunderstorm. Doing so can cause electrical shock or fire.
• The projector is designed to operate on a power supply of 100-240V AC 50/60 Hz. Ensure that your power supply
fits this requirement before attempting to use your projector.
• Do not look into the lens while the projector is on. Serious damage to your eyes could result.
• Keep any items such as magnifying glass out of the light path of the projector. The light being projected from the
lens is extensive, therefore any kind of abnormal objects that can redirect light coming out of the lens, can cause
unpredictable outcome such as fire or injury to the eyes.
• Do not cover the lens with the black lens cap or equivalent while the projector is on. Doing so can lead to melting of
the cap and possibly burning your hands due to the heat emitted from the light output.
• Do not place any objects, which are easily affected by heat, in front of the projector lens or a projector exhaust vent.
Doing so could lead to the object melting or getting your hands burned from the heat that is emitted from the light
output and exhaust.
• Handle the power cable carefully. A damaged or frayed power cable can cause electric shock or fire.
- Do not use any power cables than the supplied one.
- Do not bend or tug the power cable excessively.
- Do not place the power cable under the projector, or any heavy object.
- Do not cover the power cable with other soft materials such as rugs.
- Do not heat the power cable.
- Do not handle the power plug with wet hands.
• Turn off the projector, unplug the power cable and have the object removed by a qualified service personnel
under the following conditions:
- When the power cable or plug is damaged or frayed.
- If liquid has been spilled into the projector, or if it has been exposed to rain or water.
- If the projector does not operate normally when you follow the instructions described in this user's manual.
- If the projector has been dropped or the cabinet has been damaged.
- If the projector exhibits a distinct change in performance, indicating a need for service.
- If the projector is not to be used for an extended period of time.
• Disconnect the power cable and any other cables before carrying the projector.
• Turn off the projector and unplug the power cable before cleaning the cabinet or replacing the lamp.
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Information
CAUTION
• Do not use the tilt-foot for purposes other than originally intended. Misuses such as gripping the tilt-foot or
hanging on the wall can cause damage to the projector.
• Do not send the projector in the soft case by parcel delivery service or cargo shipment. The projector inside
the soft case could be damaged.
• When carrying the projector by the carrying handle, make sure the two screws that attach the carrying handle
to the projector cabinet are tight.
Insufficient tightening of the two screws could result in the projector falling and causing injury.
• Select [High] in Fan mode if you continue to use the projector for consecutive days. (From the menu, select
[Setup] → [Options] → [Fan Mode] → [High].)
• Do not turn off the AC power by pressing the main power switch or by unplugging the power cable when the
projector is powered on.
• Do not turn off theAC power for 60 seconds after the lamp is turned on and while the POWER indicator is blinking
green. Doing so could cause premature lamp failure.
Remote Control Precautions
•
•
•
•
•
•
•
•
Handle the remote control carefully.
If the remote control gets wet, wipe it dry immediately.
Avoid excessive heat and humidity.
Do not heat, take apart, or throw batteries into fire.
If you will not be using the remote control for a long time, remove the batteries.
Ensure that you have the batteries’ polarity (+/-) aligned correctly.
Do not use new and old batteries together, or use different types of batteries together.
Dispose of used batteries according to your local regulations.
Lamp Replacement
•
•
Be sure to replace the lamp when the message [The lamp has reached the end of its usable life. Please
replace the lamp.] appears. If you continue to use the lamp after the lamp has reached the end of its usable
life, the lamp bulb may shatter, and pieces of glass may be scattered in the lamp case. Do not touch them as
the pieces of glass may cause injury.
If this happens, contact your dealer for lamp replacement.
A Lamp Characteristic
The projector has a high-pressure mercury lamp as a light source.
A lamp has a characteristic that its brightness gradually decreases with age. Also repeatedly turning the lamp on
and off will increase the possibility of its lower brightness.
CAUTION:
When removing the lamp from a ceiling-mounted projector, make sure that no one is under the projector. Glass
fragments could fall if the lamp has been burned out.
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Important Information ----------------------------------------------------------- i
1. Introduction ---------------------------------------------------------------------- 1
ᕡ What's in the Box? --------------------------------------------------------------------------------- 1
ᕢ Introduction to the Projector --------------------------------------------------------------------- 2
ᕣ Part Names of the Projector --------------------------------------------------------------------- 3
Attaching the supplied carrying handle ------------------------------------------------- 4
Top Features-------------------------------------------------------------------------------------- 5
Terminal Panel Features----------------------------------------------------------------------- 6
ᕤ Part Names of the Remote Control ------------------------------------------------------------ 7
Battery Installation ------------------------------------------------------------------------------ 8
Remote Control Precautions ----------------------------------------------------------------- 8
Operating Range for Wireless Remote Control------------------------------------------ 8
2. Installation and Connections ------------------------------------------- 9
ᕡ Setting Up the Screen and the Projector ----------------------------------------------------- 9
Selecting a Location
---------------------------------------------------------------- 9
Throw Distance and Screen Size ----------------------------------------------------------11
ᕢ Making Connections ----------------------------------------------------------------------------- 13
Enabling the computer’s external display ----------------------------------------------- 13
Connecting Your PC or Macintosh Computer ------------------------------------------ 13
When Viewing a DVI Digital Signal ------------------------------------------------------- 14
Using Two Analog COMPUTER Inputs Simultaneously ----------------------------- 15
Connecting an External Monitor ----------------------------------------------------------- 16
Connecting Your DVD Player with Component Output ------------------------------ 17
Connecting Your VCR or Laser Disc Player -------------------------------------------- 18
Connecting the Supplied Power Cable -------------------------------------------------- 19
3. Projecting an Image (Basic Operation)-------------------------- 20
ᕡ Turning on the Projector ------------------------------------------------------------------------ 20
Note on Startup screen (Menu Language Select screen)--------------------------- 21
ᕢ Selecting a Source ------------------------------------------------------------------------------- 22
ᕣ Adjusting the Picture Size and Position----------------------------------------------------- 23
ᕤ Correcting Keystone Distortion --------------------------------------------------------------- 25
ᕥ Optimizing RGB Picture Automatically ------------------------------------------------------ 27
ᕦ Turning Up or Down Volume------------------------------------------------------------------- 27
ᕧ Turning off the Projector ------------------------------------------------------------------------ 28
ᕨ After Use -------------------------------------------------------------------------------------------- 29
v
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
4. Convenient Features ------------------------------------------------------ 30
ᕡ Turning off the Image and Sound ------------------------------------------------------------ 30
ᕢ Freezing a Picture-------------------------------------------------------------------------------- 30
ᕣ Enlarging a Picture------------------------------------------------------------------------------- 30
ᕤ Changing Lamp Mode--------------------------------------------------------------------------- 31
ᕥ Preventing the Unauthorized Use of the Projector--------------------------------------- 31
ᕦ Using the Optional Remote Mouse Receiver (NP01MR) ------------------------------ 34
5. Using On-Screen Menu --------------------------------------------------- 36
ᕡ Using the Menus---------------------------------------------------------------------------------- 36
ᕢ Menu Elements ----------------------------------------------------------------------------------- 38
ᕣ List of Menu Items-------------------------------------------------------------------------------- 39
ᕤ Menu Descriptions & Functions [Picture]--------------------------------------------------- 41
ᕥ Menu Descriptions & Functions [Image Options] ---------------------------------------- 42
ᕦ Menu Descriptions & Functions [Setup] ---------------------------------------------------- 44
ᕧ Menu Descriptions & Functions [Information] --------------------------------------------- 48
ᕨ Menu Descriptions & Functions [Reset] ---------------------------------------------------- 49
6. Maintenance ------------------------------------------------------------------- 50
ᕡ Cleaning or Replacing the Filters------------------------------------------------------------- 50
ᕢ Cleaning the Cabinet and the Lens ---------------------------------------------------------- 51
ᕣ Replacing the Lamp ----------------------------------------------------------------------------- 52
7. Appendix ------------------------------------------------------------------------- 55
ᕡ Troubleshooting ----------------------------------------------------------------------------------- 55
ᕢ Specifications-------------------------------------------------------------------------------------- 58
ᕣ Cabinet Dimensions ----------------------------------------------------------------------------- 61
ᕤ Pin Assignments of D-Sub COMPUTER Input Connector ----------------------------- 62
ᕥ Compatible Input Signal List------------------------------------------------------------------- 63
ᕦ PC Control Codes and Cable Connection ------------------------------------------------- 64
ᕧ Troubleshooting Check List -------------------------------------------------------------------- 66
vi
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Introduction
ᕡ What's in the Box?
Make sure your box contains everything listed. If any pieces are missing, contact your dealer.
Please save the original box and packing materials if you ever need to ship your projector.
Projector
J
.
D
O
T
A
A
U
E
C
T
I
X E
R
U
O
S
Y
B
D
N
A
T
T
S
/
C
N
O
E
E
L
S
R
E
T
U
N
N
E
E
M
R
E
W
S
O
P
U
T
A
T
S
P
M
A
L
M
O
Z O
C
U S
F
O
Lens cap
(24FT9641)
Soft case
(24BS7582)
O
F
F
M
A
G
N
IF
P
O
Y
W
P
E
R
IC
-
O
N
M
U
T
E
M
P
A
E
N
G
E
U
U
P
D
O
W
N
ENTER
L
-
C
L
IC
K
V
ID
E
X
E
O
M
IT
O
S
U
S
-V
ID
C
O
M
E
R
-
E
P
C
L
U
O
T
1
E
IC
K
V
R
O
P
A
U
L
U
T
O
M
E
A
D
2
J
.
A
L
S
A
M
P
E
P
M
C
T
O
D
E
IC
T
H
E
U
R
L
P
E
F
R
E
E
Z
E
Power cable
(US: 7N080220)
(EU: 7N080015)
VGA signal cable
Remote control
(7N900731)
Batteries (AAAꢀ2)
For North America only
Registration card
Limited warranty
For Europe only
Guarantee policy
Quick Setup Guide
Important Information
CD-ROM
User’s manual
Carrying handle (24FT9651)
Screw (M4ꢀ2: 24V00411)
DVI to VGA adapter (7N960231)
1
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Introduction
ᕢ Introduction to the Projector
This section introduces you to your new projector and describes the features and controls.
Congratulations on Your Purchase of the Projector
This projector is one of the very best projectors available today. The projector enables you to project precise images
up to 300 inches across (measured diagonally) from your PC or Macintosh computer (desktop or notebook), VCR,
DVD player, document camera, or a laser disc player.
You can use the projector on a tabletop or cart, you can use the projector to project images from behind the screen,
and the projector can be permanently mounted on a ceiling*1. The remote control can be used wirelessly.
1
*
Do not attempt to mount the projector on a ceiling yourself.
The projector must be installed by qualified technicians in order to ensure proper operation and reduce the
risk of bodily injury.
In addition, the ceiling must be strong enough to support the projector and the installation must be in accor-
dance with any local building codes. Please consult your dealer for more information.
Features you'll enjoy:
•
•
Auto vertical keystone correction up to +/– 30 degrees
Built-in Wall Color Correction presets provide for adaptive color correction when projecting onto non-white
screen material
•
Quick start & quick cool down
Eight seconds after turning on the power, the projector is ready to display PC or video images.
Powering down; The fans stop 30 seconds after turning off the power from the remote control or cabinet control
panel. The projector can be put away immediately after the projector is powered down.
Also, the main power of the projector can be turned off by pressing the main power switch or unplugging the
power cable even during the cool down period after the projector is turned off.
•
•
•
•
•
•
•
•
•
•
•
•
•
DVI input connector (DVI-I 29 Pin) with HDCP compatible
HDTV (1080i, 720p) and SDTV (576p, 480p) compatibility
Color Management system
Short focal length lens
Display popular wide screen and full screen aspect ratios – 16:9 and 4:3
Built-in speaker for an integrated audio solution
High resolution display - up to UXGA compatible, XGA native resolution.
Multiple video mode selections (depending on your source)
Security feature prevents unauthorized individuals from displaying images.
You can control the projector with a PC or control system using the PC Control port.
Easy set up and operation
The contemporary cabinet design is light, compact and complements any office, boardroom Auditorium.
You can use the supplied wireless remote control and the optional remote mouse receiver to operate your PC
mouse from across the room. The optional remote mouse receiver (NP01MR) supports almost any PC using a
USB connection.
About this user's manual
The fastest way to get started is to take your time and do everything right the first time. Take a few minutes now to
review the user's manual. This may save you time later on. At the beginning of each section of the manual you'll find
an overview. If the section doesn't apply, you can skip it.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Introduction
ᕣ Part Names of the Projector
Front/Top
Zoom lever
Digital Zoom Button)
Controls
M
O
O
Z
D
J .
A
A
U T O
S
U
C
O
F
E
C
T
I
X
R
U
E
O
S
B
Y
T
A N D
/ S
T
C
N
O
E
L
E
S
R
T
N
U
N
E
E
M
R
E
W
O
S
P
U
T
A
T
S
P
M
A
L
Ventilation (inlet) / Filter Cover
Two filters
Remote sensor
M
O
O
Z
S
U
C
O
F
Focus Ring
Built-in Security Slot ( )*
Lens
Lens Cap
*
This security slot supports the MicroSaver ® Security System. MicroSaver ® is a registered trademark of
Kensington Microware Inc. The logo is trademarked and owned by Kensington Microware Inc.
Rear
L
S
E
A
M
E
L
E
P
N
S
R
C
T
T
A
T
T
E
P
U
O
R
W
E
IT
EX
O
N
/
S
T
A
N
D
B
Y
S
O
U
R
C
E
A
U
T
O
A
D
J
.
Terminal Panel
Remote sensor
Monaural Speaker
(5W)
Ventilation (outlet)
Heated air is exhausted from here.
AC Input
Connect the supplied power cable's two-pin plug here, and
Main Power Switch
When you plug the supplied power cable into an active wall outlet
and turn on the Main Power, the POWER indicator turns orange
and the projector is in standby mode.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Introduction
Bottom
Rear Foot (Left / Right)
Adjustable Tilt Foot
Adjustable Tilt Foot Button
Lamp Cover
Attaching the supplied carrying handle
You can carry the projector by attaching the supplied carrying handle securely to the projector.
To attach the supplied carrying handle, use a Phillips-head screwdriver and the supplied two screws.
Place a soft cloth on the working surface before turning the projector over to prevent scratching the top cover.
Make sure that the carrying handle is attached with correct orientation as shown below.
Screw
Phillips-head screwdriver
(not supplied)
Carrying handle
CAUTION
When carrying the projector by the carrying handle, make sure the two screws that attach the carrying handle
to the projector cabinet are tight.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Introduction
Terminal Panel Features
5
8
9
2
1
S-VIDEO
IN
PC CTRL
COMPUTER
2
(DVI-I) IN
AUDIO IN
COMPUTER
1
IN
L
8777
MONITOR OUT (COMP 1)
AUDIO OUT
R
VIDEO IN
AUDIO IN
6 7
3
4
1. COMPUTER 1 IN/ Component Input Connector
(Mini D-Sub 15 Pin)
4. MONITOR OUT Connector (Mini D-Sub 15 Pin)
5. S-VIDEO IN Connector (Mini DIN 4 Pin)
Use this port to connect a PC or control system.
This enables you to control the projector using serial
communication protocol. If you are writing your own
6
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Introduction
ᕤ Part Names of the Remote Control
1
OFF
ON
POWER
3
2
MAGNIFY PIC-MUTE
PAGE
UP
4
7
6
5
8
DOWN
MENU
ENTER
EXIT
10
12
9
L-CLICK
MOUSE
R-CLICK
AUTO ADJ.
LAMP MODE
HELP
11
13
VIDEO
C
O
MPUTER
1
16
15
18
S-VIDEO
2
14
19
17
VOLUME ASPECT
21
PICTURE FREEZE
22
20
12. MOUSE R-CLICK Button*
13. VIDEO Button
1. Infrared Transmitter
14. S-VIDEO Button
2. POWER ON Button
15. COMPUTER 1/2 Button
( page 22)
3. POWER OFF Button
4. MAGNIFY (+)(–) Button
16. AUTO ADJ. Button
5. PIC-MUTE Button
17. VOLUME (+)(–) Button
6. PAGE UP/DOWN Button*
19. ASPECT Button
7. MENU Button
20. PICTURE Button
8. SELECT ꢀꢁꢂꢃ Button
9. ENTER Button
21. HELP Button
10. EXIT Button
11. MOUSE L-CLICK Button*
22. FREEZE Button
* The PAGE UP/DOWN, MOUSE L-CLICK and MOUSE R-CLICK buttons work only when the optional remote mouse
receiver is connected with your computer.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Introduction
Battery Installation
1 Press firmly and slide the
2 Install new batteries (AAA).
3 Slip the cover back over the bat-
teries until it snaps into place. Do
not mix different types of batter-
ies or new and old batteries.
battery cover off.
Ensure that you have the
batteries' polarity (+/–) aligned
correctly.
Remote Control Precautions
•
•
•
•
•
•
•
•
Handle the remote control carefully.
If the remote control gets wet, wipe it dry immediately.
Avoid excessive heat and humidity.
Do not heat, take apart, or throw batteries into fire.
If you will not be using the remote control for a long time, remove the batteries.
Ensure that you have the batteries’ polarity (+/-) aligned correctly.
Do not use new and old batteries together, or use different types of batteries together.
Dispose of used batteries according to your local regulations.
Operating Range for Wireless Remote Control
Remote sensor on projector cabinet
7m/22feet
Remote control
30°
( )
30°
*
30°
30°
7m/22feet
•
•
The infrared signal operates by line-of-sight up to a distance of about 22 feet/7 m and within a 60-degree angle of
the remote sensor on the projector cabinet.
The projector will not respond if there are objects between the remote control and the sensor, or if strong light falls
on the sensor. Weak batteries will also prevent the remote control from properly operating the projector.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Installation and Connections
This section describes how to set up your projector and how to connect video and audio sources.
Your projector is simple to set up and use. But before you get started, you must first:
1
2
Set up a screen and the projector.
Connectyourcomputerorvideoequipment
to the projector.
L
A
M
E
S
E
L
E
S
R
T
A
P
T
N
C
T
P
O
W
T
U
S
R E
E
E
T
O
N
/S
T
A
N
D
B
Y
S
O
U
R
C
E
A
U
T
O
A
D
J
.
3
Connect the supplied power cable.
NOTE: Ensure that the power cable and any
other cables are disconnected before moving
the projector. When moving the projector or
when it is not in use, cover the lens with the
lens cap.
ᕡ Setting Up the Screen and the Projector
Selecting a Location
The further your projector is from the screen or wall, the larger the image. The minimum size the image can be is
approximately 21" (0.53 m) measured diagonally when the projector is roughly 38 inches (1.0 m) from the wall or
screen. The largest the image can be is 300" (7.6 m) when the projector is about 389 inches (9.9 m) from the wall or
screen.
Screen Size (Unit: cm/inch)
609.6(W)ꢀ457.2(H) / 240(W)ꢀ180(H)
Screen Size
300"
487.7(W)ꢀ365.8(H) / 192(W)ꢀ144(H)
240
"
406.4(W)ꢀ304.8(H) / 160(W)ꢀ120(H)
200
365.8(W)ꢀ274.3(H) / 144(W)ꢀ108(H)
"
180"
304.8(W)ꢀ228.6(H) / 120(W)ꢀ90(H)
150"
243.8(W)ꢀ182.9(H) / 96(W)ꢀ72(H)
120"
203.2(W)ꢀ152.4(H) / 80(W)ꢀ60(H)
100"
162.6(W)ꢀ121.9(H) / 64(W)ꢀ48(H)
80"
121.9(W)ꢀ91.4(H) / 48(W)ꢀ36(H)
60"
81.3(W)ꢀ61.0(H) / 32(W)ꢀ24(H)
9.9/389
61.0(W)ꢀ45.7(H) / 24(W)ꢀ18(H)
304" 0"
7.9/311
42.7(W)ꢀ32(H) / 17(W)ꢀ13(H)
21"
6.6/259
5.9/233
Lens center
)
h
4.9/194
c
L
S
A
M
P
N
E
S
E
L
E
C
T
P
O
W
E
R
T
A
T
U
R
E
T
0.7/
29
O
N
/
T
A
E
X
N
D
B
Y
S
O
U
R
C
E
A
U
T
O
A
D
J
.
/in
it: m
3.9/155
3.3/129
1.0/38
2.6/103
1.3/
51
2.0/77
n
(U
e
c
n
ta
is
D
TIP:
•
•
•
The distances are indicated by intermediate values between tele and wide. Use as a rule of thumb.
The Zoom lever adjusts the image size +/-10%
9
Download from Www.Somanuals.com. All Manuals Search And Download.
This page intentionally left blank.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Installation and Connections
Throw Distance and Screen Size
The following shows the proper relative positions of the projector and screen. Refer to the table to determine the
position of installation.
Distance Chart
C
B = Vertical distance between lens center and
screen center
C = Throw distance
D = Vertical distance between lens center and
Screen center
screen bottom (top of screen for ceiling
application)
α = Throw angle
B
Lens center
α
D
NOTE: Distances may vary +/-5%.
Screen bottom
Projector bottom
8777
Screen Size
Width
C
α
B
D
Diagonal
inch mm
Height
inch
13
15
18
24
36
43
48
50
54
60
72
90
108
120
126
144
162
180
wide
tele
wide
degree
-
tele
degree
8.6
8.6
8.5
8.4
8.4
8.4
8.4
8.4
8.4
8.3
8.3
8.3
8.3
8.3
8.3
8.3
8.3
8.3
inch
mm
mm
320
381
457
610
914
1097
1219
1280
1372
1524
1829
2286
2743
3048
3200
3658
4115
4572
inch
4
5
6
8
mm
110
130
160
210
310
380
420
440
470
520
630
790
940
1050
1100
1260
1410
1570
inch
-
mm
-
720
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
inch
29
34
41
56
84
101
112
118
126
141
169
211
254
282
296
339
381
424
mm
730
inch
-2
-2
-3
-4
-6
-7
-8
-8
-8
mm
-50
-60
-70
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
21
25
533
635
17
20
427
508
28
34
46
70
84
870
1050
1410
2130
2560
2850
2990
3210
3570
4290
5370
6450
7170
7530
8610
9690
10770
10.3
10.2
10.1
10.1
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
9.9
30
762
24
610
870
1170
1770
2130
2370
2490
2670
2970
3570
4470
5370
5970
6270
7170
8070
8970
40
60
72
80
84
90
100
120
150
180
200
210
240
270
300
1016
1524
1829
2032
2134
2286
2540
3048
3810
4572
5080
5334
6096
6858
7620
32
813
-100
-140
-170
-190
-200
-210
-240
-290
-360
-430
-480
-500
-570
-640
-710
48
58
64
67
72
80
96
120
144
160
168
192
216
240
1219
1463
1626
1707
1829
2032
2438
3048
3658
4064
4267
4877
5486
6096
12
15
17
17
19
21
25
31
37
41
43
50
56
62
93
98
105
117
141
176
211
235
247
282
318
353
-9
-11
-14
-17
-19
-20
-23
-25
-28
9.9
9.9
11
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Installation and Connections
WARNING
Reflecting the Image
* Installing your projector on the ceiling must be done
by a qualified technician. Contact your dealer
for more information.
* Do not attempt to install the projector yourself.
• Only use your projector on a solid, level surface. If the
projector falls to the ground, you can be injured and
the projector severely damaged.
Using a mirror to reflect your projector’s image enables
you to enjoy a much larger image when a smaller space
is required. Contact your dealer if you need a mirror
system. If you're using a mirror system and your image
is inverted, use the MENU and SELECT buttons on your
projector cabinet or your remote control to correct the
• Do not use the projector where temperatures vary
greatly. The projector must be used at temperatures
between 41˚F (5˚C) and 104˚F (40˚C) (Eco mode
selected automatically at 95˚F to 104˚F/35˚C to 40˚C).
• Do not expose the projector to moisture, dust, or
smoke. This will harm the screen image.
• Ensure that you have adequate ventilation around your
projector so heat can dissipate. Do not cover the vents
on the side or the front of the projector.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Installation and Connections
ᕢ Making Connections
NOTE: When using with a notebook PC, be sure to connect the projector and notebook PC while the projector is in standby mode
and before turning on the power to the notebook PC.
In most cases the output signal from the notebook PC is not turned on unless connected to the projector before being powered
up.
* If the screen goes blank while using your remote control, it may be the result of the computer's screen-saver or power
management software.
Enabling the computer’s external display
Displaying an image on the notebook PC’s screen does not necessarily mean it outputs a signal to the projector.
When using a PC compatible laptop, a combination of function keys will enable/disable the external display.
Usually, the combination of the ‘Fn” key along with one of the 12 function keys gets the external display to come on or
off. For example, NEC laptops use Fn + F3, while Dell laptops use Fn + F8 key combinations to toggle through
external display selections.
Connecting Your PC or Macintosh Computer
COMPUTER 1 IN
S-VIDEO
IN
PC CTRL
COMPUTER
2
(DVI-I) IN
AUDIO IN
COMPUTER
1
IN
L
MONITOR COMP 1)
AUDUT
VIDEO IN
AUDIO IN
Audio cable (not supplied)
VGA signal cable (supplied)
To mini D-Sub 15-pin connector on the projector. It is
recommended that you use a commercially available
distribution amplifier if connecting a signal cable longer
than the cable supplied.
NOTE: For older Macintosh, use a commercially available
pin adapter (not supplied) to connect to your Mac's
video port.
PHONE
IBM VGA or Compatibles (Notebook
type) or Macintosh (Notebook type)
NOTE: The projector is not compatible with video decoded outputs of either the ISS-6020 and ISS-6010 switchers.
NOTE: An image may not be displayed correctly when a Video or S-Video source is played back via a commercially available scan
converter.
This is because the projector will process a video signal as a computer signal at the default setting. In that case, do the following.
* When an image is displayed with the lower and upper black portion of the screen or a dark image is not displayed correctly:
Project an image to fill the screen and then press the AUTO ADJ. button on the remote control or the projector cabinet.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Installation and Connections
When Viewing a DVI Digital Signal
To project a DVI digital signal, be sure to connect the PC and the projector using a DVI cable (not supplied) before
turning on your PC or projector. Turn on the projector first and select Computer 2 (Digital) from the source menu
before turning on your PC.
Failure to do so may not activate the digital output of the graphics card resulting in no picture being displayed. Should
this happen, restart your PC.
Do not disconnect the DVI cable while the projector is running. If the signal cable has been disconnected and then re-
connected, an image may not be correctly displayed. Should this happen, restart your PC.
NOTE:
• Use a DVI cable or the one compliant with DDWG (Digital Display Working Group) DVI (Digital Visual Interface) revision 1.0
standard. The DVI cable should be within 5 m (196") long. Both single and dual types of DVI cable can be used.
• The DVI (DIGITAL) connector accepts VGA (640x480), SVGA (800x600), 1152x864, XGA (1024x768) and SXGA (1280x1024 @
up to 60Hz).
AUDIO IN
COMPUTER 2 (DVI-I) IN
S-VIDEO
IN
PC CTRL
COMPUTER
2
(DVI-I) IN
AUDIO IN
AUDUT
COMPUTER
1
IN
L
MONITOR OUT (COMP 1)
R
VIDEO IN
AUDIO IN
IBM PC or Compatibles (Desktop type)
or Macintosh (Desktop type)
DVI cable (not supplied)
PHONE
Audio cable (not supplied)
14
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Installation and Connections
Using Two Analog COMPUTER Inputs Simultaneously
If you need to use two analog COMPUTER inputs simultaneously, connect a VGA signal cable as shown below.
COMPUTER 1 IN
COMPUTER 2 (DVI-I) IN
S-VIDEO
IN
PC CTRL
COMPUTER
2
(DVI-I) IN
AUDIO IN
AUDIO OUT
COMPUTER
1
IN
L
MONITOR OUT (COMP 1)
R
VIDEO IN
AUDIO IN
IBM PC or Compatibles (Desktop
type) or Macintosh (Desktop type)
VGA signal cable
(supplied)
DVI to VGA adapter
(supplied)
VGA signal cable (not
supplied)
IBM PC or Compatibles (Notebook type)
or Macintosh (Notebook type)
NOTE: When the DVI to VGA adapter is not to be used for an extended period of time, remove it from the projector. Failure to do
so may cause damage to the connector of the projector.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Installation and Connections
Connecting an External Monitor
AUDIO OUT
MONITOR OUT
S-VIDEO
IN
PC CTRL
COMPUTER
2
(DVI-I) IN
AUDIO IN
AUDIO OUT
COMPUTER
1
I
L
MONITOR OUT (COMP 1)
R
VIDEO IN
AUDIO IN
VGA signal cable (supplied)
AUDIO
IN
VGA signal cable (not supplied)
You can connect a separate, external monitor to your projector to simultaneously view on a monitor the RGB analog
image you're projecting.
NOTE:
• Daisy chain connection is not possible.
• The signal from the COMPUTER 2 IN connector cannot be output from the MONITOR OUT connector.
• When the DVI Digital signal is selected, no signals will be output from the MONITOR OUT connector.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Installation and Connections
Connecting Your DVD Player with Component Output
AUDIO IN
COMPUTER 1 IN
S-VIDEO
IN
PC CTRL
COMPUTER
2
(DVI-I) IN
AUDIO IN
AUDIO OUT
COMPUTER
1
IN
L
MONITOR COMP 1)
R
VIDEO IN
AUDIO IN
15-pin - to - RCA (female) ꢀ3 cable
adapter (ADP-CV1E)
Audio Equipment
AUDIO IN
Component video RCAꢀ3
L
R
cable (not supplied)
DVD player
L
R
Y
Cb Cr
Audio cable (not supplied)
AUDIO OUT
Component
A component signal will be automatically displayed. If not, from the menu, select [Setup] → [Options] → [Signal
Select] → [Computer 1], and then place a check mark in the Component radio button.
NOTE: Refer to your DVD player's owner's manual for more information about your DVD player's video output requirements.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Installation and Connections
Connecting Your VCR or Laser Disc Player
AUDIO IN
S-VIDEO IN
S-VIDEO
IN
PC CTRL
COMPUTER
2
(DVI-I) IN
AUDIO IN
COMPUTER
1
IN
L
MONITOR OUT (COMP 1)
AUDIO OUT
R
VIDEO IN
AUDIO IN
VIDEO IN
S-Video cable (not supplied)
Video cable (not supplied)
Audio equipment
VCR/ Laser disc player
L
R
S-VIDEO VIDEO
VIDEO OUT
AUDIO IN
AUDIO OUT
L
R
Audio cable (not supplied)
NOTE: The AUDIO IN L/MONO and R jacks (RCA) are shared between the Video and S-Video inputs.
NOTE: Refer to your VCR or laser disc player owner's manual for more information about your equipment's video output
requirements.
NOTE: An image may not be displayed correctly when a Video or S-Video source is played back in fast-forward or fast-rewind via
a scan converter.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Installation and Connections
Connecting the Supplied Power Cable
Connect the supplied power cable to the projector.
First connect the supplied power cable's two-pin plug to the AC IN of the projector, and then connect the other plug of
the supplied power cable in the wall outlet.
LAMP
STATUS
SELECT
E
N
T
E
POWER
R
IT
X
E
O
N
/
S
T
A
N
D
B
Y
S
O
U
R
C
E
A
U
T
O
A
D
J
.
To wall outlet ←
Make sure that the prongs are fully inserted into both
the AC IN and the wall outlet.
CAUTION:
Do not try to touch the ventilation outlet on the left front (when seen from the front) as it can become heated while
the projector is turned on and immediately after the projector is turned off.
CAUTION:
Do not turn off the AC power by pressing the main power switch or by unplugging the power cable when the
projector is powered on. Doing so can cause damage to the projector.
TIP: The projector can be turned off (by either the main power switch or by unplugging the power cable)
during its cool down period after it is turned off using the remote control or via the power button on the control panel.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Projecting an Image (Basic Operation)
This section describes how to turn on the projector and to project a picture onto the screen.
ᕡ Turning on the Projector
NOTE:
• The projector has two power switches: a main power switch and a POWER (ON/STAND BY) button (POWER ON and OFF on the
remote control).
• When plugging in or unplugging the supplied power cable, make sure that the main power switch is pushed to the off (ꢀ)
position. Failure to do so may cause damage to the projector.
LAMP
1. To turn on the main power to the projector, press the
STATUS
Main Power switch to the on position ( I ).
POWER
L
S
S
E
A
E
M
L
E
S
R
P
N
C
T
T
T
A
T
E
P
U
O
R
W
E
The POWER indicator will light orange.
IT
EX
O
N
/
S
T
A
N
D
B
Y
S
O
U
R
C
E
A
U
T
O
A
D
J
.
2. Remove the lens cap
MENU
3. Press the POWER (ON/STAND BY) button on the
projector cabinet or the POWER ON button on the
remote control for 1 second.
SELECT
LAMP
The POWER indicator will turn to green and the
projector will become ready to use.
STATUS
POWER
After you turn on your projector, ensure that the
computer or video source is turned on and that your
lens cap is removed.
ON/STNBY
SOURCE
AUTO ADJ.
OFF
ON
POWER
MAGNIFY PIC-MUTE
PE
NOTE: When no signal is available, a blue screen is displayed at
the factory default.
DOWN
MENU
When the projector displays a blue, black, or logo screen, the
projector will automatically switch to the Eco mode.
The projector will return to the Normal mode once a signal is
connected.
Standby
Blinking
Power On
NOTE: If you turn on the projector immediately after the lamp is
turned off or when the temperature is high, the fans run without
displaying an image for some time and then the projector will
display the image.
LAMP
LAMP
LAMP
STATUS
STATUS
POWER
STATUS
POWER
POWER
Steady orange light
Blinking green Steady green
light light
CAUTION:
The projector cannot be turned off for 60 seconds after the
lamp is turned on and while the POWER indicator is blinking
green. Doing so could cause premature lamp failure.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Projecting an Image (Basic Operation)
Note on Startup screen (Menu Language Select screen)
When you first turn on the projector, you will get the Startup menu. This menu gives you the opportunity to select one
of the 8 menu languages.
To select a menu language, follow these steps:
1. Use the SELECT ꢀ or ꢁ button to select one of the 8
languages from the menu.
MENU
OFF
ON
POWER
MAGNIFY PIC-MUTE
PAGE
UP
SELECT
2
1
DOWN
LAMP
STATUS
POWER
MENU
1
2
ENTER
EXIT
ON/STAND BY
SOURCE
AUTO ADJ.
2. Press the ENTER button to execute the selection.
After this has been done, you can proceed to the menu op-
eration.
If you want, you can select the menu language later.
NOTE: Immediately after turning on the projector, screen flicker may occur. This is normal. Wait 3 to 5 minutes until the lamp
lighting is stabilized.
When the Lamp mode is set to Eco, the LAMP indicator will light green.
If one of the following things happens, the projector will not turn on.
• If the internal temperature of the projector is too high, the projector detects abnormal high temperature. In this
condition the projector will not turn on to protect the internal system. If this happens, wait for the projector's internal
components to cool down.
• When the lamp reaches its end of usable life, the projector will not turn on. If this happens, replace the lamp.
• If the lamp fails to light, and if the STATUS indicator flashes on and off in a cycle of six times, wait a full minute and
then turn on the power.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Projecting an Image (Basic Operation)
ᕢ Selecting a Source
Selecting the computer or video source
NOTE: Turn on the computer or video source equipment connected to the projector.
Selecting from Source List
MENU
Press and quickly release the SOURCE button on the projector cabinet
to display the Source list. Each time the SOURCE button is pressed, the
input source will change as follows: “Computer 1”, “Computer 2 (Digital /
Analog)” ”Video” (VCR or laser disc player), “S-Video”,
SELECT
LAMP
STATUS
POWER
To display the selected source, allow 1 second to elapse.
ON/STAND BY
SO
AUTO ADJ.
MENU
Detecting the Signal Automatically
Press and hold the SOURCE button for a minimum of 2 seconds, the
projector will search for the next available input source. Each time you
press and hold the SOURCE button for a minimum of 2 seconds, the
input source will change as follows:
SELECT
LAMP
STATUS
POWER
ON/STAND BY
SO
AUTO ADJ.
Computer1 → Computer2 (Digital) → Computer2 (Analog) → Video →
S-Video → Computer1 → ...
TIP:
If no input signal is present, the input will be skipped.
L-CLICK
R-CLICK
Using the Remote Control
Press any one of the COMPUTER 1/2, VIDEO, S-VIDEO buttons.
MOUSE
VIDEO
COMPUTER
1
S-VIDEO
LAMP MODE
2
VOME ASPECT
HELP
URE FREEZE
TIP: The COMPUTER 2 button on the remote control toggles the Computer 2
source between [Computer 2 (Digital)] and [Computer 2 (Analog)].
Selecting Default Source
You can set a source as the default source so that it will be displayed
each time the projector is turned on.
1. Select [Setup] → [Options] → [Default Source Select] from the
menu.
The [Default Source Select] screen will be displayed.
2. Select a source as the default source, and press the ENTER
button.
3. Press the EXIT button a few times to close the menu.
4. Restart the projector.
The source you selected in step 2 will be projected.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Projecting an Image (Basic Operation)
ᕣ Adjusting the Picture Size and Position
Place your projector on a flat level surface and ensure that the projector is
square to the screen.
Lift the front edge of the projector to center the image vertically.
*
If the projected image does not appear square to the screen then use the
L
S
A
S
E
L
M
P
N
E
E
C
S
R
T
T
T
A
T
E
P
O
U
R
W
E
E
X
IT
O
N
/
S
T
A
N
D
B
Y
S
O
U
R
C
E
A
U
T
O
A
D
J
.
Move the projector left to center the image horizontally on the screen.
L
S
A
S
E
L
M
P
N
E
E
C
S
R
T
T
E
T
A
T
U
P
O
R
W
E
E
X
IT
O
N
/
S
T
A
N
D
B
Y
S
O
U
R
C
E
A
U
T
O
A
D
J
.
Adjust the Tilt Foot
1. Lift the front edge of the projector.
Adjustable Tilt
Foot Button
CAUTION:
Do not try to touch the ventilation outlet during Tilt Foot adjustment as it can
become heated while the projector is turned on and during its cool down
period after it is turned off.
1
P
U
S
H
2. Push and hold the Adjustable Tilt Foot Button on the front of the
projector to extend the adjustable tilt foot.
2
3. Lower the front of the projector to the desired height.
Adjustable Tilt Foot
4. Release the Adjustable Tilt Foot Button to lock the Adjustable tilt
foot.
There is approximately 10 degrees (up) of adjustment for the front of the
projector.
The rear foot height can be adjusted up to 0.4 inch/10 mm.
Rotate the rear foot to the desired height in order to square the image on
the projection surface, but the vertical distance from the bottom to the
desk or floor should be 0.4 inch /10mm to make the projector horizontal
on the flat surface.
4
3
E
N
T
E
R
NOTE: Rotating the rear foot too much may cause the foot to come out of the
projector.
S
-V
IN
ID
E
O
L
P
C
C
T
R
L
C
O
M
P
U
T
V
E
ID
R
E
2
O
(D
V
IN
I-
I)
IN
A
U
A
U
I
D
IO
IN
C
O
M
P
U
T
E
R
1
IN
AUDIO OUT
CAUTION:
M
O
N
IT
O
R
O
U
T
(C
O
M
P
1
)
Up
• Do not use the tilt-foot for purposes other than originally intended.
Misuses such as using the tilt foot to carry or hang (from the wall or ceiling)
the projector can cause damage to the projector.
Down
Up
Down
23
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Projecting an Image (Basic Operation)
Zoom
Use the ZOOM lever to adjust the image size on the screen.
.
J
D
A
O
T
U
A
E
C
T
I
X E
R
O U
S
Y
B
D
N
A
T
S
/
C
T
L
N
O
E
E
S
T
R
U
N
E
M
E
P
O W E R
S
T A T U S
L
A M P
O O M
S
U
C
O
F
Focus
Use the FOCUS ring to obtain the best focus.
.
J
D
A
O
T
U
A
E
C
T
I
X
R
U
E
O
S
Y
B
D
N
A
S T
/
N
O
S
E L E C T
E
U
N
E
M
E
T
R
E
W
O
S
P
U
T
A
T
S
P
M
A
L
S
U
C
O
F
24
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Projecting an Image (Basic Operation)
ᕤ Correcting Keystone Distortion
Correcting Keystone Distortion
If the screen is tilted vertically, keystone distortion becomes large. Proceed with the following
steps to correct keystone distortion
NOTE: The Keystone correction can cause an image to be slightly blurred because the correction is made electronically.
NOTE: The Keystone correction range can be made narrower, depending on a signal or its aspect ratio selection.
Adjusting with buttons on the cabinet
1. Press the SELECT ꢀ or ꢁ button with no menus displayed
The keystone bar will be displayed.
2. Use the SELECT ꢀ or ꢁ to correct the keystone distortion.
The keystone bar will be closed after a period of time.
NOTE: When the menu is displayed, the above operation is not available. When the menu is displayed, press the MENU button to
close the menu and start the Keystone correction.
From the menu, select [Setup] → [General] → [Keystone]. The changes can be saved with [Keystone Save]. (→page 44)
Adjusting with the Remote Control
1. Press the MENU button.
The menu will be displayed.
2. Press the SELECT ꢁ button to select [Setup] and press the ENTER button.
3. Press the SELECT ꢁ button to select [Keystone].
4. Press the SELECT ꢂ or ꢃ button.
Adjust so that the image is rectangular.
5. Press the MENU button.
The menu will be closed.
NOTE: The Keystone correction can cause an image to be slightly blurred because the correction is made electronically.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Projecting an Image (Basic Operation)
Adjusting with the Auto Keystone Function
The Auto Keystone correction feature will correct the vertical distortion of a projected image on the screen. No special
operation required. Just put the projector on a flat surface.
TIP: Even when the menu setting for [Auto Keystone] is turned on, [Keystone] can be adjusted manually.
To turn on [Auto Keystone], proceed the following steps.
1. Press the MENU button
The menu will be displayed.
2. Press the SELECT ꢁ button to select [Setup] and press the ENTER button.
The [General] tab will be highlighted.
3. Press the SELECT ꢁ button.
The [Auto Keystone] will be highlighted.
4. Press the SELECT ꢂ or ꢃ button to select [On].
5. Press the MENU button.
The menu will be closed.
NOTE:
•
•
•
Vertical distortions between offset angles of +/- 30 degrees can be corrected.
The Auto Keystone correction will take effect in 2 seconds after changing the projection angle during projection.
The left and right (horizontal) keystone correction is not available.
Place the projector so that the lens surface is parallel to the screen.
The rear feet of the projector can be adjusted to level the projector.
NOTE:
•
Auto and Manual Keystone correction angle could be less than 30 degrees depending on the signal and/or aspect ratios.
•
Using keystone correction can cause the image to be slightly blurred because the correction is made electronically.
NOTE:
•
When the menu is displayed, the Keystone Correction operation is not available by using the buttons on the projector cabinet.
When the menu is displayed, press the EXIT button to close the menu and then perform the Keystone correction.
From the menu, select [Setup] → [General] → [Keystone]. The changes can be saved with [Keystone Save].
•
TIP: If you have one of the following conditions, the projector’s Auto Keystone may not be performed correctly.
• The screen is tilted
• The room temperature is too high or too low
• The optical zoom is maximized or minimized
26
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Projecting an Image (Basic Operation)
ᕥ Optimizing RGB Picture Automatically
Adjusting the Image Using Auto Adjust
Optimizing an RGB image automatically.
Press the AUTO ADJ. button to optimize an RGB image automatically.
This adjustment may be necessary when you connect your computer for the first time.
[Poor picture]
MENU
L-CLICK
R-CLICK
MOUSE
VIDEO
COMPUTER
1
SELECT
S-VIDEO
LAMODE
2
VOLUME ASPECT
LAMP
STATUS
POWER
PICTURE FREEZE
ON/STAND BY
SOURCE
AUTO
[Normal picture]
NOTE:
Some signals may take time to display or may not be displayed correctly.
• The Auto Adjust function does not work for component, video, and DVI digital signals.
• If the Auto Adjust operation cannot optimize the RGB signal, try to adjust Horizontal/Vertical Position, Clock and Phase
ᕦ Turning Up or Down Volume
L-CLICK
R-CLICK
Sound level from the speaker can be adjusted.
MOUSE
VIDEO
COMPUTER
1
S-VIDEO
LAMP MODE
2
Increase volume
Decrease volume
VOLUME ASPECT
HELP
PICTURE FREEZE
TIP: When no menus appear, the SELECT ꢀ and ꢁ buttons on the projector cabinet work as a volume control.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Projecting an Image (Basic Operation)
ᕧ Turning off the Projector
To turn off the projector:
MENU
OFF
ON
1. First, press the POWER (ON/STAND BY) button on
the projector cabinet or the POWER OFF button on
the remote control. The [Power Off / Are you sure?]
message will appear.
POWER
MAGY PIC-MUTE
PAGE
UP
SELECT
DOWN
LAMP
STATUS
POWER
MENU
ENTER
ON
SOURCE
AUTO ADJ.
EXIT
Power On
Fan running
Standby
2. Secondly, press the ENTER button or press the
POWER (ON/STAND BY) or the POWER OFF button
again.
LAMP
LAMP
LAMP
STATUS
POWER
STATUS
POWER
STATUS
POWER
The power indicator will glow orange. After the
projector turns off, the cooling fans keep operating
for 30 seconds (Cool-down time).
Steady green light
Blinking
orange light
Steady orange
light
Immediately after turning on the projector and
displaying an image, you cannot turn off the
projector for 60 seconds.
L
S
E
A
E
M
L
E
C
T
S
R
P
N
T
T
A
T
E
P
U
S
O
R
W
E
IT
EX
O
N
/
S
T
A
N
D
B
Y
S
O
U
R
C
E
A
U
T
O
A
D
J
.
3. Finally, turn off the Main Power switch. The power
indicator will go out.
TIP: The main power of the projector can be turned off by pressing
the main power switch or by unplugging the power cable even
during the cool down period after the projector is turned off.
NOTE: Do not turn off the main power within 10 seconds of making
adjustment or setting changes and closing the menu.
Doing so can cause loss of adjustments and settings.
CAUTION:
Parts of the projector will become heated during operation. Use caution when picking up the projector immediately
after it has been operating.
CAUTION:
• The projector cannot be turned off for 60 seconds after the lamp is turned on and while the POWER indicator is
blinking green. Doing so could cause premature lamp failure.
• Do not turn off the AC power by pressing the main power switch or by unplugging the power cable when the
projector is powered on. Doing so can cause damage to the projector.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Projecting an Image (Basic Operation)
ᕨ After Use
Preparation: Make sure that the projector is turned off.
1. Unplug the power cable.
2. Disconnect any other cables.
3. Retract adjustable tilt feet if extended.
4. Cover the lens with the lens cap.
5. Put the projector and accessories in the supplied soft case.
Place the projector in the soft case with the lens facing upward as shown below. This is to prevent the lens from
damage.
Insert the projector with the lens
facing upward
N
O
D
N
A
T
S
/
Y
B
E
C
R
U
O
S
T
U
A
D
A
O
O
P
.
J
W
R E
T
A
T
A
R
T
E
S
U
C
O
F
Z
E
E
T
L
.
A
A
O
S
R
T
O
E
Y
D
S
N
NOTE: When placing the projector in the soft case, retract the tilt feet and the rear feet. Failure to do so may case damage to the
projector.
CAUTION:
Use caution when putting the projector in the soft case immediately after the projector has been operating. The
projector cabinet is hot.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Convenient Features
³ Turning off the Image and Sound
Press the PIC-MUTE button to turn off the image and sound for a short
period of time. Press again to restore the image and sound.
OFF
ON
POWER
MAGNIFY PIC-MUTE
PAGE
UP
OWN
MENU
ENTER
NOTE:
Sound from the AUDIO OUT jack (Stereo mini) on thecan be turned off.
EXIT
· Freezing a Picture
Press the FREEZE button to freeze a picture. Press again to resume
motion.
1
S-VIDEO
LAMP MODE
HELP
2
VOLUME ASPECT
PICTURE FREEZE
ᕣ Enlarging a Picture
You can enlarge the picture up to four times.
NOTE: The maximum magnification may be less than four times depending on
the signal.
To do so:
1. Press the MAGNIFY (+) button to magnify the picture.
To move the magnified image, use the SELECT ꢀ,ꢁ,ꢂ or
ꢃbutton.
OFF
ON
POWER
MAGNIFY PIC-MUTE
PAGE
UP
DOWN
ME
ENTER
EXIT
OFF
ON
POWER
MAGNIFY PIC-MUTE
PAGE
UP
DOWN
MENU
ENTER
EXIT
2. Press the MAGNIFY (-) button to return the image to the
original size.
OFF
ON
POWER
MAGNIFY PIC-MUTE
PAGE
UP
DOWN
M
ENTER
EXIT
30
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Convenient Features
ᕤ Changing Lamp Mode
This feature enables you to select two brightness modes of the lamp:
Normal and Eco modes. The lamp life can be extended by using the Eco mode.
Lamp Mode
Description
Status of LAMP indicator
LAMP
Normal Mode
This is the default setting (100% Off
Brightness).
STATUS
POWER
Eco Mode
Select this mode to increase the
lamp life (approx. 80% Brightness).
*approx. 75% Brightness: VT695
Steady Green light
LAMP
STATUS
POWER
To change to the [Eco] mode, do the following:
1. Press the LAMP MODE button on the remote control to display [Lamp Mode] screen.
2. Use the SELECT ꢀ or ꢁ button to select [Eco] mode.
3. Press the ENTER button.
To change from [Eco] to [Normal], Go back to Step 2 and select [Normal]. Repeat Step 3.
NOTE:
•
The Lamp Mode can be changed by using the menu.
Select [Setup] → [General] → [Lamp Mode].
•
•
The lamp life remaining and lamp hours used can be checked in [Usage Time]. Select [Information] →[Usage Time].
If the projector is overheated in Normal mode, there may be a case where the Lamp mode automatically changes to Eco mode
to protect the projector. When the projector is in Eco mode, the picture brightness decreases. When the projector comes back
to normal temperature, the Lamp mode returns to Normal mode.
Thermometer symbol [ ] indicates the lamp mode is automatically set to Eco mode because the internal temperature is too
high.
ᕥ Preventing the Unauthorized Use of the Projector
To enable the Security function:
1. Press the MENU button.
The menu will be displayed.
2. Use the SELECT ꢀ or ꢁ button to select [Setup] and press the ENTER button.
3. Use the SELECT ꢂ or ꢃ button to select [Installation].
4. Use the SELECT ꢀ or ꢁ button to select [Security] and press the SELECT ꢃ button.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Convenient Features
5. Use the SELECT ꢀ or ꢁ button to select [On] and press the ENTER button.
The [Security Keyword] screen will be displayed.
6. Type in a combination of the four SELECT buttons ꢀꢁꢂꢃ and press the ENTER button.
NOTE: A keyword must be 4 to 10 digits in length. Please make a note of your keyword.
The [Confirm Keyword] screen will be displayed.
NOTE:
Do not forget your keyword. However, if you forget your keyword, or your dealer will provide you with your Release
7. Type in the same combination of SELECT button ꢀꢁꢂꢃ and press the ENTER button.
The confirmation screen will be displayed.
8. Select [Yes] and press the ENTER button.
The Security function has been enabled.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Convenient Features
To turn on the projector when Security is enabled:
1. Press the Main Power Switch to the On position (I).
2. Press and hold the POWER ON or the ON/STAND BY button for a minimum of 1 second.
The projector will be turned on and display a message to the effect that the projector is security-protected.
3. Press the MENU button.
The Security Keyword screen will be displayed.
4. Enter your keyword in the Security Keyword screen and press the ENTER button.
You can view the projected image.
NOTE: The security disable mode is maintained until the main power is turned off (by setting the main power switch to "O" or
unplugging the power cord).
To disable the Security function:
1. Press the MENU button.
The menu will be displayed.
2. Use the SELECT ꢀ or ꢁ button to select [Setup] and press the ENTER button.
3. Use the SELECT ꢂ or ꢃ button to select [Installation].
4. Use the SELECT ꢀ or ꢁ button to select [Security] and press the SELECT ꢃ button.
5. Use the SELECT ꢀ or ꢁ button to select [Off] and press the ENTER button.
The keyword confirmation screen will be displayed.
6. Type in your keyword and press the ENTER button.
When the correct keyword is entered, the Security function will be disabled.
NOTE:
•
If you forget your keyword, contact your dealer. Your dealer will provide you with your keyword in exchange for your request
code. Your request code is displayed in the Keyword Confirmation screen. In this example [NB52-YGK8-2VD6-K585-JNE6-
EYA8] is a request code.
•
The [Security] setting cannot be cancelled by using the [Reset] of the menu.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Convenient Features
ᕦ Using the Optional Remote Mouse Receiver (NP01MR)
The optional remote mouse receiver enables you to operate your computer’s mouse functions from the remote control.
It is a great convenience for clicking through your computer-generated presentations.
Connecting the remote mouse receiver to your computer
If you wish to use the remote mouse function, connect the mouse receiver and computer.
The mouse receiver can be connected directly to the computer’s USB port (type A).
NOTE: Depending on the type of connection or OS installed on your computer, you may have to restart your computer or change
your computer settings.
Computer
Remote mouse receiver
To USB port of PC or Macintosh
When operating a computer via the remote mouse receiver
7m/22 feet
30˚
30˚
Remote sensor on the
remote mouse receiver
When connecting using the USB terminal
For PC, the mouse receiver can only be used with a Windows 98/Me/XP*, Windows 2000 or Mac OS X 10.0.0 or later
operating system.
* NOTE: In SP1 or older version of Windows XP, if the mouse cursor will not move correctly, do the following:
Clear the Enhance pointer precision check box underneath the mouse speed slider in the Mouse Properties dialog box [Pointer
Options tab].
NOTE: Wait at least 5 seconds after disconnecting the mouse receiver before reconnecting it and vice versa. The computer may
not identify the mouse receiver if it is repeatedly connected and disconnected in rapid intervals.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Convenient Features
Operating your computer’s mouse from the remote control
You can operate your computer's mouse from the remote control.
PAGE UP/DOWN Button: scrolls the viewing area of the window or to move to the previous or next slide in PowerPoint
on your computer.
SELECTꢀꢁꢂꢃ Buttons: moves the mouse cursor on your computer.
MOUSE L-CLICK Button: works as the mouse left button.
MOUSE R-CLICK Button: works as the mouse right button.
About Drag Mode:
By pressing the MOUSE L-CLICK or R-CLICK button for 2 or 3 seconds then releasing, the drag mode is set and the
drag operation can be performed simply by pressing the SELECT ꢀꢁꢂꢃ button. To drop the item, press the MOUSE
L-CLICK (or R-CLICK) button. To cancel it, press the MOUSE R-CLICK (or L-CLICK) button.
NOTE: When you operate the computer using the SELECT ꢀꢁꢂ or ꢃ button with the menu displayed, both the menu and the
mouse pointer will be affected. Close the menu and perform the mouse operation.
TIP: You can change the Pointer speed on the Mouse Properties dialog box on the Windows. For more information, see the user
documentation or online help supplied with your computer.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Using On-Screen Menu
ᕡ Using the Menus
NOTE: The on-screen menu may not be displayed correctly while interlaced motion video image is projected.
1. Press the MENU button on the remote control or projector cabinet to display the Menu.
OFF
ON
POWER
MAGNIFY PIC-MUTE
PAGE
UP
DOWN
MENU
ENTER
EXIT
2. Press the SELECT ꢀ or ꢁ button on the remote control or the projector cabinet to highlight the menu for
the item you want to adjust or set.
OFF
ON
POWER
MAGNIFY PIC-MUTE
PAGE
UP
DOWN
MENU
ENTER
EXIT
3. Press the SELECT ꢃ button or the ENTER button on the remote control or the projector cabinet to select
a submenu or item.
OFF
ON
POWER
MAGNIFY PIC-MUTE
PAGE
UP
DOWN
MENU
ENTER
T
36
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Using On-Screen Menu
4. Use the SELECT ꢀ or ꢁ button on the remote control or the
projector cabinet to select the item you want to adjust or set.
5. Adjusting the level of a selected item or selecting an item.
Slide bar
Solid triangle
OFF
ON
POWER
MAGNIFY PIC-MUTE
PAGE
UP
DOWN
MENU
ENTER
Radio button
OFF
ON
POWER
MAGNIFY PIC-MUTE
PAGE
UP
DOWN
MENU
ENTER
EXIT
For Adjusting items (Slide bar)
Slide bar .......... Indicates settings or the direction of adjustment.
• Use the SELECT ꢂꢃ buttons to adjust the item.
OFF
ON
For Selecting items (Solid triangle)
POWER
MAGNIFY PIC-MUTE
PAGE
UP
Solid triangle .... Indicates further choices are available. A highlighted
triangle indicates the item is active.
(1) Use the SELECT ꢃ button to select the item.
(2) Use the SELECT ꢀꢁ buttons to highlight the item you want to set.
(3) Press the ENTER button. The selected item will be displayed.
DOWN
MENU
ENTER
EXIT
For Selecting items (Radio button)
Radio button .... Use this round button to select an option in a dialog
box.
• Use the SELECT ꢀꢁ buttons to select the item.
Changes are stored until you adjust it again.
Press the EXIT button to return to the previous screen.
OFF
ON
POWER
MAGNIFY PIC-MUTE
PAGE
UP
6. Repeat steps 2-5 to adjust an additional item, or press the
MENU button to close the menu.
DOWN
MENU
ENTER
EXIT
37
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Using On-Screen Menu
· Menu Elements
Title
Slide bar
Highlight
Source
Off Timer remaining
time
Radio button
Solid triangle
Check mark
Tab
Thermometer symbol
Key Lock symbol
Menu windows or dialog boxes typically have the following elements:
Title .......................................... Indicates the menu title.
Highlight................................... Indicates the selected menu or item.
Source ...................................... Indicates the currently selected source.
Off Timer remaining time ......... Indicates the remaining countdown time when the Off Timer is preset.
Solid triangle ............................ Indicates further choices are available. A highlighted triangle indicates the item is active.
Tab ........................................... Indicates a group of features in a dialog box. Selecting on any tab brings its page to the front.
Radio button ............................ Use this round button to select an option in a dialog box.
Check mark .............................. Indicates the item is selected.
Slide bar ................................... Indicates settings or the direction of adjustment.
Key Lock symbol ...................... Indicates the Control Panel Lock is enabled.
Thermometer symbol ............... Indicates the lamp mode is forcibly set to Eco mode because the internal temperature is too
high.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Using On-Screen Menu
» List of Menu Items
Some menu items are not available depending on the input source.
Resettable
Picture
Default
*
Item
Yes
Preset
1 to 6
Detail Settings General
Reference
High-Bright, Presentation, Video, Movie, Graphic, sRGB
Dynamic, Natural, Black Detail
6500, 7800, 8500, 9300
Yes
Yes
Yes
Gamma Correction
Color Temperature
White Balance
Contrast RGB, Brightness RGB
Contrast
Yes
Yes
Yes
Yes
Yes
Brightness
Sharpness
Color
Hue
Reset
Resettable
Yes
Image Options
Default
*
Item
Aspect Ratio
Cinema Position
Horizontal
Vertical
Clock
Phase
Normal, Wide Zoom, Cinema, Native
Yes
Yes
Yes
Yes
Yes
Yes
*
*
*
*
*
Video Filter
Off, Less, More
Setup
Default
Item
Resettable
Yes
General
Auto Keystone (VT695/VT595 only) Off
Off, On
Keystone
Keystone Save
Wall Color
Yes
Yes
Yes
Off
Off
Off, On
Off, Blackboard, Blackboard(Gray), Light yellow,
Light green, Light blue, Sky blue, Light rose, Pink
Normal, Eco
English, Deutsch, Français, Italiano, Español,
Português, Nederlands, Svenska, Norsk, Suomi,
Lamp Mode
Language
Normal
English
Yes
–
, Magyar, Polski, Türkçe,
,
,
,
,
,
, Dansk
Beep
Orientation
On
Off, On
Yes
Yes
Installation
Desktop Front Desktop Front, Ceiling Rear, Desktop Rear,
Ceiling Front
Communication Speed
Control Panel Lock
Security
Menu Color Select
Menu Display Time
Background
Off Timer
Auto Adjust
Auto Start
Power Management
Fan Mode
19200
Off
Off
4800, 9600, 19200
Off, On
Off, On
–
Yes
–
Color
Color, Monochrome
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Auto 45 sec Manual, Auto 5 sec, Auto 15sec, Auto 45 sec
Blue
Off
Normal
Off
Off
Blue, Black, Logo
Off, 0:30, 1:00, 2:00, 4:00, 8:00, 12:00, 16:00
Off, Normal, Fine
Off, On
Off, 0:05, 0:10, 0:20, 0:30
Auto, High
Options
Auto
Last
Default Source Select
Last, Auto, Computer, Computer 1, Computer
2(Digital), Computer 2 (Analog), Video, S-Video
• Computer 1, Computer 2 (Digital), Computer 2
(Analog):
*
The asterisk (*) indicates that the default setting varies depending on the signal.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Using On-Screen Menu
Signal Select
Computer 1(VT695/VT595) RGB/Component RGB/Component, RGB, Component
Computer 2 (Analog) (VT695/VT595) RGB/Component RGB/Component, RGB, Component
Computer(VT590/VT490/VT59/VT49) RGB/Component RGB/Component, RGB, Component
Yes
Yes
Yes
Yes
Video
Auto
Auto
On
Auto, NTSC3.58, NTSC4.43, PAL, PAL-M,
PAL-N, PAL60, SECAM
S-Video
Auto, NTSC3.58, NTSC4.43, PAL, PAL-M,
PAL-N, PAL60, SECAM
Yes
Yes
Deinterlace
Off, On
Information
Item
Usage Time
Lamp Life Remaining
Lamp Hours Used
Filter Hours Used
Source index
Horizontal Frequency
Vertical Frequency
Signal Type
Source
RGB, Component, Video, S-Video, HDTV, Digital
Video Type
Sync Type
NTSC, NTSC3.58, NTSC4.43, PAL, PAL-M, PAL-N, PAL60, SECAM
Separate Sync, Composite Sync, Sync on Green, Sync on Video
Sync Polarity
Scan Type
Interlace, Non-interlace
Version
Product
Serial Number
Firmware
Data
Reset
Item
Current Signal
All Data
Clear Lamp Hours
Clear Filter Hours
40
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Using On-Screen Menu
¿ Menu Descriptions & Functions [Picture]
Preset
When selecting user adjustable [Preset], the submenu will be displayed.
You can customize each gamma or color. To do so, first select [Preset] and press the ENTER button, then proceed
using the following steps.
Detail Settings
Selecting Reference Setting [Reference]
This option allows you to adjust neutral tint for yellow, cyan or magenta. There are six factory presets optimized for
various types of images, you can set user adjustable settings.
High-Bright............ Recommended for the use in a brightly lit room.
Presentation .......... Recommended for making a presentation using a PowerPoint file.
Video ..................... Recommended for standard video such as a TV program.
Movie .................... Recommended for film based video such as a movie (DVD or HDTV).
Graphic.................. Recommended for viewing accurate colors in graphics.
sRGB ..................... Standard color values.
Selecting Gamma Correction Mode [Gamma Correction]
Each mode is recommended for:
Dynamic ................ Creates a high-contrast picture.
Natural .................. Natural reproduction of the picture.
Black Detail ........... Emphasizes detail in dark areas of the picture.
Adjusting Color Temperature [Color Temperature]
This option allows you to select the color temperature of your choice.
NOTE: When [High-Bright] or [Presentation] is selected in [Reference], [Color Temperature] is not available.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Using On-Screen Menu
Adjusting White Balance [White Balance]
This allows you to adjust the white balance. Contrast for each color (RGB) to adjust the white level of the screen;
Brightness for each color (RGB) is used to adjust the black level of the screen.
Adjusting Contrast, Brightness, Sharpness, Color and Hue
You can adjust contrast, brightness, sharpness, color and hue.
Contrast ................ Adjusts the intensity of the image according to the incoming signal (White level of the image).
Brightness ............. Adjusts the brightness level or the black level of the image.
Sharpness ............. Controls the detail of the image for Video (not valid for RGB).
Color ..................... Increases or decreases the color saturation level (not valid for RGB).
Hue........................ Varies the color level from +/- green to +/-blue. The red level is used as reference. This adjustment is only
valid for Video and Component inputs (not valid for RGB).
Reset
The settings and adjustments for [Picture] will be returned to the factory settings with the exception of the following;
Preset numbers and [Reference] within the [Preset] screen.
The settings and adjustments under [Detail Settings] within the [Preset] screen that are not currently selected will not be reset.
´ Menu Descriptions & Functions [Image Options]
Selecting Aspect Ratio [Aspect Ratio]
Aspect Ratio allows you to select the best Aspect mode to display your source image.
You can also display the Aspect Ratio menu by pressing the ASPECT button on the remote control.
Normal
Wide Zoom
Cinema
Native
When 4:3 is selected from
the source (i.e. DVD player),
the following selections will
display:
Standard
4:3 Aspect
Left and right
stretched
Left and right
stretched
Normal
Wide Zoom
Cinema
When 16:9 is selected from
the source (i.e. DVD player),
the following selections will
display:
16:9 image displayed
in 4:3 mode
Left and right
stretched
Left and right stretched to
display the true aspect
Native (RGB only): Turns off the scaling feature. The projector displays the current image in its true resolution.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Using On-Screen Menu
NOTE:
• When you are displaying an RGB image with a higher resolution than the projector’s native resolution, the image will be
displayed in the projector’s native resolution. In this case [Native] is not available from the menu.
Only when displaying an RGB image with a lower resolution than the projector's native resolution, will the image be able to be
displayed in its true resolution [Native].
• When Computer 2 (Digital) is selected, some options of Aspect Ratio are not available depending on the signal.
• You can adjust the image position for Cinema aspect. See [Cinema Position] for setting the image position.
Copyright
Please note that using this projector for the purpose of commercial gain or the attraction of public attention in a venue such as a
coffee shop or hotel and employing compression or expansion of the screen image with a [Aspect Ratio] setting may raise concern
about the infringement of copyrights which are protected by copyright law.
Adjusting the Vertical Position of Image [Cinema Position] (for Cinema only)
This feature adjusts the vertical position of the image when viewing video with Cinema aspect ratio selected.
When [Cinema] is selected in [Aspect Ratio], the image is displayed with black borders on the top and bottom.
You can adjust the vertical position from the top to the bottom of the black area.
NOTE: This option is available only when [Cinema] is selected in [Aspect Ratio].
Adjusting Horizontal/Vertical Position, Clock and Phase [Horizontal/Vertical/Clock/Phase]
(available for RGB signal only)
You can adjust the image manually for position and stability; [Horizontal], [Vertical], [Clock] and [Phase].
[Horizontal/Vertical]
Adjusts the image location horizontally and vertically.
[Clock]
Use this item to fine tune the computer image or to remove any vertical banding that might appear. This function
adjusts the clock frequencies that eliminate the horizontal banding in the image. This adjustment may be neces-
sary when you connect your computer for the first time.
[Phase]
Use this item to adjust the clock phase or to reduce video noise, dot interference or cross talk. (This is evident
when part of your image appears to be shimmering.)
Use [Phase] only after the [Clock] is complete.
NOTE:
A projected image may not be displayed correctly during adjustment of [Clock] or [Phase]. This is normal.
NOTE: The [Horizontal] and [Vertical] options can be adjusted for component signals.
Selecting Video Filter Level [Video Filter] (not available for Digital RGB, Video and S-Video)
Select one of the three levels for reducing video noise: Off, Less or More.
Off ......................... The low-pass filter is turned off.
Less ...................... The low-pass filter is applied partially.
More...................... The low-pass filter is applied fully.
NOTE:
• Selecting [Off] will give best image quality by way of higher bandwidth. Selecting [Less] will soften the image and selecting
[More] will soften the image more.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Using On-Screen Menu
² Menu Descriptions & Functions [Setup]
[General]
8777
Enabling Auto Keystone [Auto Keystone]
This feature allows the projector to detect its tilt and correct vertical distortion automatically.
To turn on the Auto Keystone feature, select [On].
Correcting Vertical Keystone Distortion Manually [Keystone]
You can correct vertical distortion manually.
Saving Vertical Keystone Correction [Keystone Save]
This option enables you to save your current keystone settings.
Off ......................... Does not save current keystone correction settings
On ......................... Saves current keystone correction settings
Saving your change once affects all sources. The changes are saved when the projector is off.
NOTE: When [Auto Keystone] is set to [On], [Keystone Save] is not available. Next time you turn on the power, the Auto Keystone
function will work and the data stored with [Keystone Save] will be invalid.
Selecting Wall Color Correction Mode [Wall Color]
This function allows for quick adaptive color correction in applications where the screen material is not white.
The following nine options are available: Off, Blackboard, Blackboard (Gray), Light yellow, Light green, Light blue, Sky
blue, Light rose and Pink.
Selecting Lamp Mode [Lamp Mode]
This feature enables you to select two brightness modes of the lamp: Normal and Eco modes. The lamp life can be
extended by using the Eco mode.
Normal Mode ........ This is the Default setting (100% Brightness).
Eco Mode .............. Select this mode to increase the lamp life (approx. 75% Brightness).
Selecting Menu Language [Language]
You can choose one of 21 languages for the on-screen menu.
Enabling Key Sound and Error Sound [Beep]
This feature turns on or off the keypad sound or alarm when a button on the cabinet and the remote control is pressed
or an error occurs.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Using On-Screen Menu
[Installation]
Selecting Projector Orientation [Orientation]
This sets your image for your type of projection application. The options are:
desktop front projection, ceiling rear projection, desktop rear projection, and ceiling front projection.
Desktop front
Ceiling rear
Desktop rear
Ceiling front
Selecting Communication Speed [Communication Speed]
This feature sets the baud rate of the PC Control port (Mini DIN 8 Pin). It supports data rates from 4800 to 19200 bps.
The default is 19200 bps.
Select the appropriate baud rate for your equipment to be connected (depending on the equipment, a lower baud rate
may be recommended for long cable runs).
Your selected communication speed will not be affected even when [Reset] is done from the menu.
Disabling the Cabinet Buttons [Control Panel Lock]
This option turns on or off the Key Lock function for cabinet buttons.
NOTE:
• The Control Panel Lock setting will not affect the remote control or PC Control Functions.
• When the cabinet buttons are disabled, pressing and holding the EXIT button on the projector cabinet for about 10 seconds will
change the setting to enable.
• The Key Lock icon will be displayed at the bottom right of the menu when Control Panel Lock is enabled.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Using On-Screen Menu
Enabling Security [Security]
This feature turns on or off the Security function.
Selecting Menu Color [Menu Color Select]
You can choose between two color modes for menu color: color and monochrome.
Selecting Menu Display Time [Menu Display Time]
This option allows you to select how long the projector waits after the last touch of a button to turn off the menu.
The preset choices are [Manual], [Auto 5 sec], [Auto 15 sec], and [Auto 45 sec].
Selecting a Color for Background [Background]
Use this feature to display a blue, black or logo when no signal is available.
[Options]
Setting Off Timer [Off Timer]
You can use the Off Timer feature to turn off the projector automatically at a preset time.
Eight preset times can be selected: Off, 0:30, 1:00, 2:00, 4:00, 8:00, 12:00 and 16:00.
Setting Auto Adjust [Auto Adjust]
This feature sets the Auto Adjust mode so that the RGB image can be automatically or manually adjusted for noise
and stability. You can automatically make adjustment in two ways: Normal and Fine
Off ......................... The RGB image will not be automatically adjusted.
You can manually optimize the RGB image.
Normal .................. Default setting. The RGB image will be automatically adjusted. Normally select this option.
Fine ....................... Select this option if fine adjustment is needed. It takes more time to switch to the source than when [Normal]
is selected.
Enabling Auto Start [Auto Start]
Turns the projector on automatically when the power cable is inserted into an active power outlet. This eliminates the
need to always use the POWER button on the remote control or projector cabinet.
To use the Auto Start function, you must first press the main power switch to the position “On” (I) before plugging the
power cable.
Enabling Power Management [Power Management]
When this option is selected you can enable the projector to automatically turn off (at the selected time: 5 min., 10
min., 20 min., 30 min.) if there is no signal received by any input.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Using On-Screen Menu
Enabling Fan Speed Mode [Fan Mode]
This option allows you to select two modes for fan speed: Auto mode and High speed mode.
Auto ...................... The built-in fans automatically run at a variable speed according to the internal temperature.
High ...................... The built-in fans run at a fixed high speed.
When you wish to cool down the temperature inside the projector quickly, select [High].
NOTE: It is recommended that you select High speed mode if you continue to use the projector for consecutive days.
Selecting Default Source [Default Source Select]
You can set the projector to default to any one of its inputs each time the projector is turned on.
Last ....................... Sets the projector to default to the previous or last active input each time the projector is turned on.
Auto ...................... Searches for an active source in order of Computer 1 → Computer 2 (Digital) → Computer 2 (Analog) →
Video → S-Video → Computer 1 and displays the first found source.
Computer 1 ........... Displays the RGB source from the COMPUTER 1 IN connector every time the projector is started up.
Computer 2 (Digital) ... Displays the DVI digital source from the COMPUTER 2 IN connector every time the projector is started up.
Computer 2 (Analog) .. Displays the RGB source from the COMPUTER 2 IN connector every time the projector is started up.
Video ..................... Displays the Video source from the VIDEO IN connector every time the projector is started up.
S-Video ................. Displays the Video source from the S-VIDEO IN connector every time the projector is started up.
Selecting Signal Format [Signal Select
[Computer 1],[Computer 2 (Analog)]
Allows you to choose, [Computer 1], or [Computer 2 (Analog)] for an RGB source such as a computer, or
[Component] for a component video source such as a DVD player. Normally select [RGB/Component] and the projec-
tor automatically detects a component signal. However there may be some component signals that the projector is
unable to detect. If this is the case, select [Component].
[Video & S-Video System Select]
This feature enables you to select composite video standards automatically or manually.
Normally select [Auto] and the projector will automatically detect the video standard.
In the case where the projector has difficulty detecting the video standard, select the appropriate video standard from
the menu.
This must be done for Video and S-Video respectively.
Enabling the deinterlace [Deinterlace]
Turns on or off the deinterlace function for a telecine signal.
On ......................... Default standard setting.
Off ......................... Select this option if there is any jitter or artifacts in video.
NOTE: This feature is not available for RGB, 480p, 576p and HDTV signals.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Using On-Screen Menu
¶ Menu Descriptions & Functions [Information]
Displays the status of the current signal and lamp usage. This item has three pages. The information included is as
follows:
[Usage Time]
[Lamp Life Remaining] (%)*
[Lamp Hours Used] (H)
[Filter Hours Used] (H)
*
The progress indicator shows the percentage of remaining bulb life.
The value informs you of the amount of lamp usage. When the remaining lamp time reaches 0, the Remaining
Lamp Time bar indicator changes from 0% to 100 Hours and starts counting down.
If the remaining lamp time reaches 0 hours, the projector will not turn on regardless of whether the lamp mode
is set to Normal or Eco.
Lamp life(H)
Model
Replacement lamp
Normal
Eco
456-8777
2000
3000
8777
[Source]
[Source Index]
[Vertical Frequency]
[Video Type]
[Horizontal Frequency]
[Signal Type]
[Sync Type]
[Sync Polarity]
[Scan Type]
48
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Using On-Screen Menu
[Version]
[Product]
[Serial Number]
[Firmware] Version
[Data] Version
ᕨ Menu Descriptions & Functions [Reset]
Returning to Factory Default [Reset]
The Factory Default feature allows you to change adjustments and settings to the factory preset for a (all) source (s)
except the following:
[Current Signal]
Resets the adjustments for the current signal to the factory preset levels.
The items that can be reset are: [Preset], [Contrast], [Brightness], [Color], [Hue], [Sharpness], [Aspect Ratio],
[Horizontal], [Vertical], [Clock], [Phase] and [Video Filter].
[All Data]
Reset all the adjustments and settings for all the signals to the factory preset.
All items can be reset except [Language], [Communication Speed], [Security], [Lamp Life Remaining], [Lamp
Hours Used] and [Filter Hours Used].
To reset the lamp usage time, see “Clearing Lamp Hour Meter [Clear Lamp Hours] below”.
Clearing Lamp Hour Meter [Clear Lamp Hours]
Resets the lamp clock back to zero. Selecting this option displays submenu for a confirmation. Select [Yes] and press the
ENTER button.
NOTE: Elapsed time of the lamp use will not be affected even when [Reset] is done from the menu.
NOTE: The projector will turn off and go into standby mode after 2100* hours (up to 3100* hours in Eco mode) of service. If this
happens, press the HELP button on the remote control for ten seconds to reset the lamp clock back to zero. Do this only after
replacing the lamp.
Clearing the Filter Usage Hours [Clear Filter Hours]
Resets the filter usage back to zero. Selecting this option displays submenu for a confirmation. Select [Yes] and press the
ENTER button.
NOTE: Elapsed time of the filter use will not be affected even when [Reset] is done from the menu.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Maintenance
This section describes the simple maintenance procedures you should follow to clean the filters and replace the lamp.
ᕡ Cleaning or Replacing the Filters
The air-filter sponge keeps dust and dirt from getting inside the projector and should be cleaned after every 100 hours
of operation (more often in dusty conditions). If the filter is dirty or clogged, your projector may overheat.
CAUTION
•
•
•
Turn off the projector, turn off the main power switch and unplug the projector before replacing the filters.
Only clean the outside of the filter cover with a vacuum cleaner.
Do not attempt to operate the projector without the filter cover.
To clean the air-filter:
Vacuum the filter-through the filter cover.
.
J
D
A
O
T
U
A
E
C
T I
X
R
U
E
O
S
Y
B
D
N
A
T
T
S
/
C
N
O
E
L
E
S
R
E
T
U
N
N
E
E
M
R
E
W
S
O
P
U
T
A
T
S
P
M
A
L
M
O
O
Z
S
U
C
O
F
To replace the filter (sponge):
1. Remove the filter cover by pushing down on the catch of the cover until you feel it detach.
NOTE: The 8777 hastwo filters;
Catch
2. Gently peel off the filter (sponge) and replace it with the new one.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Maintenance
3. Reinstall the new filter cover.
4. Clear the filter hours used.
To reset the filter usage time, from the menu, select [Reset] → [Clear Filter Hours].
NOTE: Do not wash the filter with soap and water. Soap and water will damage the filter membrane. Before replacing the filter,
remove dust and dirt from the projector cabinet. Keep out dust and dirt during filter replacement.
NOTE: When you replace the lamp, it is also wise to replace the filter. The filter comes in the same package with your replacement
lamp.
· Cleaning the Cabinet and the Lens
1. Turn off the projector before cleaning.
2. Clean the cabinet periodically with a damp cloth. If heavily soiled, use a mild detergent. Never use
strong detergents or solvents such as alcohol or thinner.
3. Use a blower or lens paper to clean the lens, and be careful not to scratch or mar the lens.
.
J
D
A
O
T
U
A
E
C
T
I
X E
R
U
O
S
Y
B
D
N
A
L
S
T
A
E
T
S
/
M
E
L
C
N
O
S
R
P
N
E
C
E
L
T
T
T
E
S
A
T
E
R
P
U
S
O
R
E
T
W
E
U
N
N
E
E
M
R
E
W
S
O
P
U
IT
T
EX
A
T
S
O
P
N
M
A
/
S
L
T
A
N
D
B
Y
S
O
U
R
C
E
A
U
T
O
A
D
J
.
M
O
O
Z
F
O C U S
51
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Maintenance
» Replacing the Lamp
After your lamp has been operating for 2000 hours (up to 3000*1 hours in Eco mode) or longer, the LAMP indicator in
the cabinet will blink red and the message [The lamp has reached the end of its usable life. Please replace the
lamp.] *1 will appear. Even though the lamp may still be working, replace it at 2000*1 (up to 3000*1 hours in Eco mode)
hours to maintain optimal projector performance. After replacing the lamp, be sure to clear the lamp hour meter.
CAUTION
•
DO NOT TOUCH THE LAMP immediately after it has been used. It will be extremely hot. Turn the projector off,
wait 30 seconds, turn off the main power switch and then disconnect the power cable. Allow at least one hour
for the lamp to cool before handling.
•
•
DO NOT REMOVE ANY SCREWS except two lamp case screws. You could receive an electric shock.
Do not break the glass on the lamp housing.
Keep finger prints off the glass surface on the lamp housing. Leaving finger prints on the glass surface might
cause an unwanted shadow and poor picture quality.
•
The projector will turn off and go into standby mode after 2100*1 (up to 3100*1 hours in Eco mode) hours of service.
If this happens, be sure to replace the lamp. If you continue to use the lamp after 2000*1 hours (up to 3000*1 hours
in Eco mode) of use, the lamp bulb may shatter, and pieces of glass may be scattered in the lamp case. Do not
touch them as the pieces of glass may cause injury. If this happens, contact your dealer for lamp
replacement.
1 NOTE: This message will be displayed under the following conditions:
*
• for one minute after the projector has been powered on
• when the POWER ON/STAND BY button on the projector cabinet or the POWER OFF button on the remote control is pressed
To turn off the message, press any button on the projector cabinet or the remote control.
To replace the lamp:
Optional lamp and tools needed for replacement:
•
Replacement lamp 456-8777
1.Place the projector on a soft cloth and turn it over to access the lamp cover on the bottom.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Maintenance
2. Remove the lamp cover.
(1)Press firmly and slide the lamp cover by 1 cm (0.4”)
• Do not force to pull the lamp cover
(2)Push to release two catches on both sides and slide the lamp cover off.
1
3
2
1
3. Remove the lamp housing.
(1)Loosen the two screws securing the lamp housing until the phillips screwdriver goes into a freewheeling
condition. The two screws are not removable.
(2)Remove the lamp housing by holding it.
Interlock
NOTE: There is an interlock on this case to prevent the risk of electrical shock. Do not attempt to circumvent this interlock.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Maintenance
4. Install a new lamp housing.
(1)Insert a new lamp housing until the lamp housing is plugged into the socket.
CAUTION
Do not use a lamp other than the replacement lamp 456-8777.
Order this from your dealer.
(2)Secure it in place with the two screws.
Be sure to tighten the screws.
5. Reattach the lamp cover.
(1)Place the lamp cover, aligning it with the guiding line.
(2)Slide the lamp cover back until it snaps into place.
6. Connect the supplied power cable, turn on the Main Power switch and turn on the projector.
7. Finally, select the menu → [Reset] → [Clear Lamp Hours] to reset the lamp usage hours.
NOTE: When the lamp exceeds 2100* hours (up to 3100* hours in Eco mode) of service, the projector cannot turn on and the
menu is not displayed.
If this happens, press the HELP button on the remote control for ten seconds to reset the lamp clock back to zero.
When the lamp time clock is reset to zero, the LAMP indicator goes out.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Appendix
ᕡ Troubleshooting
This section helps you resolve problems you may encounter while setting up or using the projector.
Indicator Messages
Power Indicator
Indicator Condition
Projector Condition
The main power is off
The projector is getting ready to turn on. Wait for a moment.
Note
Off
–
Blinking light
Steady light
Green
0.5 sec On,
0.5 sec Off
2.5 sec On,
0.5 sec Off
0.5 sec On,
0.5 sec Off
Off Timer is enabled.
–
Orange
The projector is cooling down.
Wait for a moment.
Green
The projector is turned on.
The projector is in Standby.
–
–
Orange
Status Indicator
Indicator Condition
Off
Projector Condition
Note
Normal
–
Blinking light
Red
1 cycle (0.5 sec On, Lamp cover error or lamp housing error Replace the lamp cover or lamp
2.5 sec Off)
housing correctly.
2 cycle (0.5 sec On, Temperature error
0.5 sec Off)
The projector is overheated. Move
the projector to a cooler location.
Fans will not work correctly.
4 cycle (0.5 sec On, Fan error
0.5 sec Off)
6 cycle (0.5 sec On, Lamp error
0.5 sec Off)
Lamp fails to light. Wait a full
minute and then turn on again.
Green
Re-firing the lamp (The projector is cool- The projector is re-firing.
ing down.)
Wait for a moment.
Steady light
Orange
Cabinet button is locked
You have pressed cabinet button
when Cabinet Button is locked.
Lamp Indicator
Indicator Condition
Projector Condition
Note
Off
Normal
–
Blinking light
Steady light
Red
Lamp has reached its end of life. Lamp Replace the lamp.
replacement message will be displayed.
Lamp has been used beyond its limit. The Replace the lamp.
projector will not turn on until the lamp is
replaced.
Red
Green
Lamp mode is set to Eco mode
–
Over-Temperature Protection
If the temperature inside the projector rises too high, the over-temperature protector will automatically turn off the
lamp with the STATUS indicator blinking (2-cycle On and Off.)
Should this happen, do the following:
• Unplug the power cable after the cooling fans stop.
• Move the projector to a cooler location if the room where you are presenting is particularly too warm.
• Clean the ventilation holes if they are clogged with dust.
• Wait about 60 minutes until the inside of the projector becomes cool enough.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Appendix
Problem
Check These Items
Does not turn on
•
Check that the power cable is plugged in and that the power button on the projector cabinet or the remote
•
•
room where you are presenting is particularly warm, move the projector to a cooler location.
Check to see if the lamp usage exceeds 2100* hours (up to 3100* hours : Eco mode). If so, replace the lamp.
•
•
•
•
The lamp may fail to light. Wait a full minute and then turn on the power again.
Will turn off
No picture
Use the COMPUTER, the VIDEO or the S-VIDEO button on the remote control to select your source (Computer,
Remove the lens cap.
•
•
•
•
•
•
Reset the settings or adjustments to factory preset levels using the [Reset] in the Menu. (→ page 49)
the power to the notebook PC.
In most cases the output signal from the notebook PC is not turned on unless connected to the projector
before being powered up.
* If the screen goes blank while using your remote control, it may be the result of the computer's screen-
saver or power management software.
•
•
See also the next page.
Picture suddenly
becomes dark
When one of the following happens, the Lamp mode automatically changes from Normal to Eco.
* When there are no signals → To return to the Normal mode, select another available source.
* When the room where you' re presenting is particularly warm → Move the projector to a cooler location, or
set [Fan Mode] to [High].
Color tone or hue is
unusual
•
•
Check if an appropriate color is selected in [Wall Color]. If so, select an appropriate option. (→ page 44)
Image isn’t square to
the screen
•
•
Picture is blurred
•
•
•
•
Should this happen, let the projector stand until there is no condensation on the lens.
Image is scrolling
vertically, horizontally
or both
•
•
Use the COMPUTER, the VIDEO or the S-VIDEO button on the remote control to select your source (Computer,
•
•
•
Remote control does
not work
Indicator is lit or
blinking
•
Cross color in RGB
mode
•
•
For more information contact your dealer.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Appendix
If there is no picture, or the picture is not displayed correctly.
•
Power on process for the projector and the PC.
Be sure to connect the projector and notebook PC while the projector is in standby mode and before turning on
the power to the notebook PC.
In most cases the output signal from the notebook PC is not turned on unless connected to the projector before
being powered up.
NOTE: You can check the horizontal frequency of the current signal in the projector’s menu under Information. If it reads
“0kHz”, this means there is no signal being output from the computer. (→ page 48 or go to next step)
•
Enabling the computer’s external display.
Displaying an image on the notebook PC’s screen does not necessarily mean it outputs a signal to the projec-
tor. When using a PC compatible laptop, a combination of function keys will enable/disable the external display.
Usually, the combination of the ‘Fn” key along with one of the 12 function keys gets the external display to come
on or off. For example, NEC laptops use Fn + F3, while Dell laptops use Fn + F8 key combinations to toggle
through external display selections.
•
•
Non-standard signal output from the computer
If the output signal from a notebook PC is not an industry standard, the projected image may not be displayed
correctly. Should this happen, deactivate the notebook PC’s LCD screen when the projector display is in use.
Each notebook PC has a different way of deactivate/reactivate the local LCD screens as described in the
previous step. Refer to your computer’s documentation for detailed information.
Image displayed is incorrect when using a Macintosh
When using a Macintosh with the projector, set the DIPswitch of the Mac adapter (not supplied with the projec-
tor) according to your resolution. After setting, restart your Macintosh for the changes to take affect.
For setting display modes other than those supported by your Macintosh and the projector, changing the DIP
switch on a Mac adapter may bounce an image slightly or may display nothing. Should this happen, set the DIP
switch to the 13” fixed mode and then restart your Macintosh. After that, restore the DIP switches to a
displayable mode and then restart the Macintosh again.
NOTE: A Video Adapter cable manufactured by Apple Computer is needed for a PowerBook which does not have a mini D-Sub
15-pin connector.
•
•
Mirroring on a PowerBook
*
When using the projector with a Macintosh PowerBook, output may not be set to 1024 x 768 unless “mirror-
ing” is off on your PowerBook. Refer to owner’s manual supplied with your Macintosh computer for mirroring.
Folders or icons are hidden on the Macintosh screen
Folders or icons may not be seen on the screen. Should this happen, select [View] → [Arrange] from the Apple
menu and arrange icons.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Appendix
ᕢ Specifications
This section provides technical information about the 8777 projector's performance.
Model Number
8777
Optical
LCD Panel
0.63" p-Si TFT active-matrix with Micro Lens Array
Resolution
Lens
1024 ꢀ768 pixels* native, up to UXGA with
Advanced AccuBlend
Manual zoom and manual focus
F1.7 - 2.0 f=18.9 - 22.7 mm
Lamp
200 W DC lamp (150W Eco mode)
Light Output**
2500 lumens (approx. 75% in Eco mode)
Contrast Ratio
Image Size (Diagonal)
600: 1 (full white: full black)
21 - 300 inches / 0.5 - 7.6 m
Projection Distance
28" - 424" / 0,7 - 10,7 m
Projection Angle
Tele: 8.3° - 8.6°/ Wide: 9.9° − 10.3°
Keystone Correction
+/- 30° Vertical (Auto Keystone on VT695/VT595 only)
Electrical
Inputs
1RGB/Component(D-Sub15Pin), 1RGB(Digital/Analog)(DVI-I
29 Pin, HDCP*** supported), 1 S-Video (DIN 4 Pin), 1 Video (RCA), 1 (L/R)
RCAAudio, 1 Stereo Mini Audio, 1 PC Control (DIN 8 Pin)
Outputs
Video Compatibility
1 RGB (D-Sub 15 Pin), 1 Stereo Mini Audio
NTSC, NTSC4.43, PAL, PAL-60, PAL-N, PAL-M, SECAM,
HDTV: 1080i, 1080i/50Hz, 720p, 576p, 480p, 480i/60Hz
Horizontal: 15 kHz to 100 kHz (RGB: 24 kHz or over)
Vertical: 50 Hz to 120 Hz
Scan Rate
Video Bandwidth
RGB: 80 MHz (-3dB)
Color Reproduction
Horizontal Resolution
16.7 million colors simultaneously, Full color
NTSC / NTSC4.43/PAL/PAL-M/PAL-N/PAL60: 540 TV lines
SECAM: 300 TV lines
1024 dots (H) x 768 dots (V).
RGB:
External Control
RS232, IR
58
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Appendix
Separate Sync / Composite Sync / Sync on Green / Sync on Video
Sync Compatibility
Built-in Speaker
5W (monaural)
Power Requirement
Input Current
100 - 240V AC, 50 / 60 Hz
3.1 - 1.3A
Power Consumption
9W in Standby mode /
285W in Lamp Normal mode / 220W in Lamp Eco mode
Mechanical
Installation Orientation
Dimensions
Desktop/Front, Desktop/Rear, Ceiling/Front, Ceiling/Rear
12.2" (W)ꢀ4.4" (H)ꢀ10.2" (D)
309mm (W)ꢀ112mm (H)ꢀ258mm (D)
(not including protrusions)
Weight
approx. 6.6 lbs / 3.0 kg
Environmental Considerations Operational Temperatures : 41° to 104°F (5° to 40°C),
(Eco mode selected automatically at 95°F to 104°F/35°C to 40°C)
20% to 80% humidity (non-condensing)
Storage Temperatures : 14° to 122°F (-10° to 50°C),
20% to 80% humidity (non-condensing)
*
Effective pixels are more than 99.99%.
** This is the light output value (lumens) when the [Preset] mode is set to [High-Bright]. If any other mode
is selected as the [Preset] mode, the light output value may drop slightly.
*** What is HDCP/HDCP technology?
HDCP is an acronym for High-bandwidth Digital Content Protection. High bandwidth Digital Content
Protection (HDCP) is a system for preventing illegal copying of video data sent over a Digital Visual
Interface (DVI).
If you are unable to view material via the DVI input, this does not necessarily mean the projector
is not functioning properly. With the implementation of HDCP, there may be cases in which
certain content is protected with HDCP and might not be displayed due to the decision/intention of the
HDCP community (Digital Content Protection, LLC).
59
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Appendix
Regulations
For United States:
UL Approved (UL 60950 - 1)
Meets FCC Class B requirements
For Canada:
UL Approved (CSA 60950 - 1)
Meets DOC Canada Class B requirements
For Australia/New Zealand:
Meets AS/NZS CISPR.22 Class B
For Europe:
Meets EMC Directive (EN55022, EN55024, EN61000-3-2, EN61000-3-3)
Meets Low Voltage Directive (EN60950 - 1, TÜV GS Approved)
For additional information visit:
For information on our optional accessories, visit our website or see our brochure.
The specifications are subject to change without notice.
60
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Appendix
ᕣ Cabinet Dimensions 8777
A U D I O I N
V I D E O I N
R
A U D I O O U T
M O N I T O R O U T ( C O M P 1 )
I N
A U D I O I N
L
C O M P U T E R
1
I N
C O M P U T E R
2
( D V I - I ) I N
P C C T R L
S - V I D E O
R
E
T
N
E
E
X
T
I
A U T O A D J S . O U R C E
O N / S T A N D B Y
P O W E R
S T A T U S
L A M P
S E L E C T
M E N U
Z O O M
F O C U S
Lens center
83 (3.3")
308.7 (12.2")
71.35 (2.8")
Lens center
PUSH
Unit: mm (inch)
61
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Appendix
ᕤ Pin Assignments of D-Sub COMPUTER Input Connector
Mini D-Sub 15 Pin Connector
Pin No. RGB Signal (Analog)
YCbCr Signal
11 12 13 14 15
6
7
8
9
10
1
2
3
Red
Cr
Y
Cb
1
2
3
4
5
Green or Sync on Green
Blue
4
5
6
7
Ground
Ground
Red Ground
Green Ground
Blue Ground
Signal Level
Video signal : 0.7Vp-p (Analog)
Sync signal : TTL level
Cr Ground
Y Ground
Cb Ground
8
9
No Connection
Sync Signal Ground
No Connection
Bi-directional DATA (SDA)*
Horizontal Sync or Composite Sync
Vertical Sync
10
11
12
13
14
15
Data Clock*
* Only COMPUTER 1 input connector supported.
62
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Appendix
ᕥ Compatible Input Signal List
Horizontal: 15KHz to 100KHz (RGB: 24KHz or over)
Vertical: 50Hz to 120Hz
Signal
Resolution
( Dots )
Frequency H.
( kHz )
15.73
15.63
15.73
Refresh Rate
( Hz )
59.94
50.00
60.00
50.00
59.94
59.95
66.67
72.81
75.00
75.00
85.01
70.08
87.85
87.85
56.25
60.32
72.19
75.00
85.06
74.55
60.00
70.07
74.93
75.03
85.00
75.00
75.06
60.00
75.00
85.00
60.02
NTSC
PAL
PAL60
SECAM
VESA
IBM
–
–
–
–
15.63
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
640 ꢀ 480
640 ꢀ 480
640 ꢀ 480
640 ꢀ 480
640 ꢀ 480
640 ꢀ 480
640 ꢀ 480
720 ꢀ 350
720 ꢀ 350
720 ꢀ 400
800 ꢀ 600
800 ꢀ 600
800 ꢀ 600
800 ꢀ 600
800 ꢀ 600
832 ꢀ 624
1024 ꢀ 768
1024 ꢀ 768
1024 ꢀ 768
1024 ꢀ 768
1024 ꢀ 768
1152 ꢀ 864
1152 ꢀ 870
1280 ꢀ 960
1280 ꢀ 960
1280 ꢀ 960
1280 ꢀ 1024
1280 ꢀ 1024
1280 ꢀ 1024
1280 ꢀ 1024
1280 ꢀ 1024
1400 ꢀ 1050
1600 ꢀ 1200
1600 ꢀ 1200
1600 ꢀ 1200
1600 ꢀ 1200
–
31.47
31.48
35.00
37.86
37.50
39.38
43.27
31.47
39.44
39.44
35.16
37.88
48.08
46.88
53.67
49.72
48.36
56.48
60.24
60.02
68.68
67.50
68.68
60.00
75.00
85.94
63.98
64.30
69.87
79.98
91.15
63.98
75.00
81.25
87.50
93.75
15.63
31.25
33.75
28.13
45.00
31.47
15.73
15.63
MAC
VESA
VESA
IBM
VESA
IBM
IBM
IBM
VESA
VESA
VESA
VESA
VESA
MAC
VESA
VESA
MAC
VESA
VESA
VESA
MAC
@ D
@ D
@ D
@ D
@ D
@ D
@ D #
@ D #
@ D #
VESA
@
@
#
#
@ D #
@ D #
VESA
MAC
MAC
VESA
VESA
VESA
VESA
VESA
60.38
65.18
75.02
85.02
60.02
60.00
65.00
70.00
@
@
@
@
@
@
@
@
#
#
#
#
#
#
#
#
VESA
VESA
75.00
SDTV(576i)
SDTV(576p)
HDTV (1080i)
HDTV (1080i)
HDTV (720p)
SDTV (480p)
DVD YCbCr
DVD YCbCr
50.00 Interlace
50.00 Progressive
60.00 Interlace
50.00 Interlace
60.00 Progressive
59.94 Progressive
59.94 Interlaced
50.00 Interlaced
D
–
@ D #
@ D #
@ D #
D
1920 ꢀ 1080
1920 ꢀ 1080
1280 ꢀ 720
–
–
–
#
: Images in above flagged with # are compressed with Advanced AccuBlend.
: Images in above flagged with “D” are supported by the DVI digital signals.
D
NOTE: Some composite sync signals may not be displayed correctly.
Signals other than those specified in the table above may not be displayed correctly. If this should happen, change
the refresh rate or resolution on your PC. Refer to Display Properties help section of your PC for procedures.
UXGA (1600ꢀ1200) is supported for separate sync signal only.
63
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Appendix
ᕦ PC Control Codes and Cable Connection
PC Control Codes
Function
Code Data
POWER ON
02H
02H
02H
00H
00H
00H
00H
00H
00H
00H
00H
00H
00H
00H
00H
00H
00H
00H
00H
00H
00H
00H
00H
00H
00H
00H
00H
00H
02H
02H
02H
02H
02H
00H
00H
00H
00H
02H
03H
01H
01H
01H
01H
01H
12H
13H
14H
15H
POWER OFF
01H
03H
03H
03H
03H
03H
10H
11H
12H
13H
INPUT SELECT COMPUTER 1
01H
1AH
02H
06H
0BH
09H
22H
0AH
0EH
13H
INPUT SELECT COMPUTER 2 (Digital) 02H
INPUT SELECT COMPUTER 2 (Analog) 02H
INPUT SELECT VIDEO
INPUT SELECT S-VIDEO
PICTURE MUTE ON
PICTURE MUTE OFF
SOUND MUTE ON
02H
02H
02H
02H
02H
02H
SOUND MUTE OFF
NOTE: Contact your local dealer for a full list of the PC Control Codes if needed.
Cable Connection
Communication Protocol
Baud rate ........................................ 19200 bps
Data length ..................................... 8 bits
Parity.............................................. No parity
Stop bit .......................................... One bit
X on/off .......................................... None
Communications procedure ........... Full duplex
NOTE: Depending on the equipment, a lower baud rate may be recommended for long cable runs.
64
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Appendix
ᕧ Troubleshooting Check List
Before contacting your dealer or service personnel, check the following list to be sure repairs are needed also by
referring to the “Troubleshooting” section in your user’s manual. This checklist below will help us solve your problem
more efficiently.
* Print this page and the next page for your check.
Frequency of occurrence ꢀ always ꢀ sometimes (How often?_____________________) ꢀ other (__________________)
Power
No power (POWER indicator does not light green) See also “Sta-
tus Indicator (STATUS)”.
Shut down during operation.
Power cable's plug is fully inserted into the wall outlet.
Lamp cover is installed correctly .
Power Management is turned off (only models with the Power
Management function).
Power cable's plug is fully inserted into the wall outlet.
Main power switch is pressed to the ON position.
Lamp cover is installed correctly .
Lamp Hours Used (lamp operation hours) was cleared after
lamp replacement.
Off Timer is turned off (only models with the Off Timer function ).
No power even though you press and hold the POWER button
for 1 second.
Video and Audio
No image is displayed from your PC or video equipment to the
projector.
Parts of the image are lost.
Still unchanged even though you press the AUTO ADJUST but-
ton.
Still unchanged even though you carry out [Reset] in the
projector’s menu.
Still no image even though you connect the projector to the PC
first, then start the PC.
Enabling your notebook PC’s signal output to the projector.
•
A combination of function keys will enable/disable the ex-
ternal display. Usually, the combination of the “Fn” key along
with one of the 12 function keys turns the external display
on or off.
Image is shifted in the vertical or horizontal direction.
Horizontal and vertical positions are correctly adjusted on a
computer signal.
Input source's resolution and frequency are supported by the
projector.
No image (blue or black background, no display).
Still no image even though you press the AUTO ADJUST but-
ton.
Still no image even though you carry out [Reset] in the
projector’s menu.
Signal cable's plug is fully inserted into the input connector
A message appears on the screen.
( _____________________________________________ )
The source connected to the projector is active and available.
Still no image even though you adjust the brightness and/or
the contrast.
Input source's resolution and frequency are supported by the
projector.
Some pixels are lost.
Image is flickering.
Still unchanged even though you press the AUTO ADJUST but-
ton.
Still unchanged even though you carry out [Reset] in the
projector’s menu.
Image shows flickering or color drift on a computer signal.
Image appears blurry or out of focus.
Still unchanged even though you checked the signal’s resolu-
tion on PC and changed it to projector’s native resolution.
Still unchanged even though you adjusted the focus.
No sound.
Image is too dark.
Audio cable is correctly connected to the audio input of the
projector.
Still unchanged even though you adjusted the volume level.
Remains unchanged even though you adjust the brightness
and/or the contrast.
Image is distorted.
AUDIO OUT is connected to your audio equipment (only mod-
els with the AUDIO OUT connector).
Image appears to be trapezoidal (unchanged even though you
carry out the [Keystone] adjustment).
Other
Remote control does not work.
Buttons on the projector cabinet do not work ( only models with
the Key Lock function).
No obstacles between the sensor of the projector and the re-
mote control.
Control Panel Lock is not turned on or is disabled in the menu.
Projector is placed near a fluorescent light that can disturb the
infrared remote controls.
Still unchanged even though you press and hold the EXIT but-
ton for a minimum of 10 seconds.
Batteries are new and are not reversed in installation.
66
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Appendix
In the space below please describe your problem in detail.
Information on application and environment where your projector is used
Projector
Installation environment
Screen size:
Model number:
inch
Serial No.:
Screen type: ꢀ White matte ꢀ Beads ꢀ Polarization
ꢀ Wide angle ꢀ High contrast
Date of purchase:
Lamp operating time (hours):
Lamp Mode:
Throw distance:
feet/inch/m
ꢀ Normal ꢀ Eco
Orientation: ꢀ Ceiling mount ꢀ Desktop
Power outlet connection:
Information on input signal:
Horizontal synch frequency
Vertical synch frequency
Synch polarity
[
[
] kHz
] Hz
ꢀ Connected directly to wall outlet
ꢀ Connected to power cord extender or other (the num-
ber of connected equipment______________)
H ꢀ (+) ꢀ (–)
ꢀ Connected to a power cord reel or other (the number
V ꢀ (+) ꢀ (–)
of connected equipment______________)
Synch type
ꢀ Separate ꢀ Composite
ꢀ Sync on Green
Computer
STATUS Indicator:
Steady light
Manufacturer:
ꢀ Orange ꢀ Green
Model number:
Notebook PC ꢀ / Desktop ꢀ
Native resolution:
Refresh rate:
Flashing light
[
] cycles
Remote control model number:
Video adapter:
Other:
PC
Projector
DVD player
Video equipment
Signal cable
VCR, DVD player, Video camera, Video game or other
Standard or other manufacturer’s cable?
Model number:
Distribution amplifier
Model number:
Switcher
Length:
inch/m
Manufacturer:
Model number:
Model number:
Adapter
Model number:
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Audio Visual Products
2900 Dukane Drive
St. Charles, Illinois 60174
Toll-free: 800-676-2487
Fax: 630-584-5156
e-mail: [email protected]
#401-8777-00
Download from Www.Somanuals.com. All Manuals Search And Download.
|