Dixon Lawn Mower ZTR 361 User Manual

;
.
.
Date: 9/88  
TECHNICAL DATA BROCHURE- ZTR 361  
IMPORTANT - READ OPERATOR'S MANUAL BEFORE OPERATING OR MAKING ADJUSTMENTS  
Seat Adjustment  
Loosen bolts on sliding brackets under each side of the seat, slide seat forward or backward  
to desired position, tighten bolts. Do not operate the mower with bracket bolts in "loose"  
position.  
Mower Blade Operation  
1. To start mower blades, pull up slightly on blade drive switch handle and move it  
forward to the "ON" position.  
2. To stop mower blades, move switch handle to the "OFF" position.  
Body Removal  
1. Disconnect throttle cable from engine.  
2. Disconnect wiring loom from the body by turning threaded collar on the connector in a  
counterclockwise direction. This connector is located at the left rear of the body.  
3. Remove four control lever bolts and remove upper control levers (P/N 9079 & 9080).  
4. Remove the two acorn nuts on the body floor and release latches on the rear of body  
near each side.  
.
5. Place height adjustment lever in the vertical position. Carefully lift body from chassis.  
6. For assembly, reverse above procedure.  
Safety Checks - "IMPORTANT"  
1. After reassembly of body onto chassis and while seated on the mower, attempt to start engine  
with mower deck engaged. The engine should not start. If the engine does start, return mower  
to an Authorized Dixon Dealer for adjustment or repair.  
2. Disengage mower deck and start engine with the operator in a normal seated position on  
the mower. Engage mower deck and remove weight from the seat. The engine should stop. If  
the engine continues to run when the operator rises from seat, return mower to an  
Authorized Dixon Dealer for adjustment or repair.  
Parking Brake Adjustment  
1. Remove body as described above.  
2. Tighten nut on brake rod (P/N 2533), located in front of the transaxle on each side, just  
enough to prevent brake from slipping when engaged. CAUTION: Over tightening may cause  
premature wear on the brake band (P/N 5085).  
Mower Deck Drive Belt Adjustment  
No adjustment necessary The spring loaded idler pulley maintains proper tension throughout  
belt life.  
Removing Mower Deck  
1. Remove deck drive belt by pulling spring loaded idler pulley away from belt and remove  
belt from electric clutch.  
2. Remove the clevis pins (P/N 3072) from the L -rods at rear of deck and slide free from  
slots.  
3. Remove the clevis pin (P/N 3072) from the lift linkage at the front of deck.  
4. Remove cotter pin from shaft (P/N 1332) located at front of mower deck on sli de plates  
welded at battery box. Slide shaft free.  
5. Raise front of mower chassis and roll mower free of mower deck assembly.  
6. To install deck, reverse above procedure.  
Removing Mower Blade  
1. Secure mower blade (P/N 1324) from turning.  
2. Observe blade position when removing.  
3. Remove blade bolt (P/N 3268), lock washer (P/N 3065) and blade washer (P/N 6113).  
4. To reinstall, reverse above procedure.  
WARNING: Sharp edges on blade can cause injury! Caution should be exercised when  
service is required on the blade.  
P/N 8111  
Box 1569  
Coffeyville, Kansas 67337-0945  
(316)251-2000  
Airport Industrial Park  
Download from Www.Somanuals.com. All Manuals Search And Download.  
-
o
Q)  
02  
n
TRANSAXLE ASSEMBLY (MODEL ZTR 361)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
-
a
G)  
t
n
MOWER DECK (MODEL 361)  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Code Alarm Remote Starter SRT 9000 User Manual
Cooper Lighting Indoor Furnishings 1449 User Manual
Cooper Lighting Indoor Furnishings Combo Edge User Manual
Craftsman Lawn Mower 91738841 User Manual
Crate Amplifiers Musical Instrument Amplifier GT15 15R User Manual
Earthquake Sound Stereo Amplifier XJ 300 FR User Manual
EverFocus Flat Panel Television EN 7542H User Manual
Faber Ventilation Hood Inca Pro 30 User Manual
Fundex Games Games 0728 User Manual
Gefen Stereo Receiver EXT HDMI13IR FO 141 User Manual